A.O. Smith 100233988 ProLine® 50 gal Natural Gas Conventional Water Heater Installation manual

Add to my manuals
36 Pages

advertisement

A.O. Smith 100233988 ProLine® 50 gal Natural Gas Conventional Water Heater Installation manual | Manualzz
Installa on Instruc ons and
Use & Care Guide
Residential Gas
Water Heater
Residen al Atmospheric Gas Water Heater
with the Flammable Vapor Igni on Resistant Safety System
Read this manual and the labels on the water heater before you install,
operate, or service it. If you have difficulty following the direc ons, or
aren’t sure you can safely and properly do any of this work yourself:
• Call our Technical Assistance Hotline at 1-800-527-1953. We can help you with installa on, opera ons, troubleshoo ng, or maintenance. Before you call, write down
the model and serial number from the water heater’s data plate.
Incorrect installa on, opera on, or service can damage the water heater, your house
and other property, and present risks including fire, scalding, electric shock, and
explosion, causing serious injury or death.
Table of Contents Page
IMPORTANT SAFETY INFORMATION ............................................. 3
GETTING STARTED ........................................................................ 7
INSTALLATION ............................................................................. 14
OPERATION ................................................................................. 23
TROUBLESHOOTING ................................................................... 25
MAINTENANCE ........................................................................... 28
NOTES ......................................................................................... 31
REPAIR PARTS ............................................................................. 35
WARNING: If the informa on in
these instruc ons is not followed
exactly, a fire or explosion may
result causing property damage,
personal injury or death.
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instruc ons.
• If you cannot reach your gas supplier, call the fire department.
Installa on and service must be performed by a qualified installer, service
agency or the gas supplier.
LOW LEAD
CONTENT
Keep this manual in the pocket on heater for future reference whenever maintenance, adjustment or service is required.
Retain your original receipt as proof of purchase.
100263112
January 2015
COMPLETED INSTALLATION TYPICAL
Vent
pipe
Cold water
shut off
Expansion
tank
(Connect to
cold water
supply)
Hot
water
line
Cold
water
line
Dra hood
T&P
relief
valve
T&P
discharge
pipe
Gas supply
shut off
Drain valve
Gas supply
Drain pan
discharge
pipe
Gas control
valve/thermostat
Sediment Trap
Metal drain pan
Read and follow all safety messages and instruc ons in
this manual.
This is the safety alert symbol. It is used to alert you to
poten al physical injury hazards. Obey all safety messages that follow this symbol to avoid possible property
damage, serious injury or death. Do not remove any
permanent instruc ons, labels, or the data plate from either the outside of
the water heater or on the inside of the access panels. Keep this manual
near the water heater.
Important informa on to keep
Fill out this sec on and keep this
manual in the pocket of the water
heater for reference.
Date Installed:
Model number:
Serial number:
DANGER
DANGER indicates hazardous situaon that, if not avoided, will result
in death or serious injury.
WARNING
WARNING indicates a hazardous
situa on that, if not avoided, could
result in death or serious injury.
CAUTION
CAUTION indicates a hazardous
situa on that, if not avoided, could
result in minor or moderate injury.
NOTICE
Maintenance performed:*
Date:
NOTICE indicates prac ces not
related to physical injury.
WARNING! If the informa on in these instruc ons is not followed exactly,
a fire or explosion may result causing property damage, personal injury or
death. Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
An odorant is added by the gas supplier to the gas used by this water heater.
This odorant may fade over an extended period of me. Do not depend upon
this odorant as an indica on of leaking gas. We recommend installing a fuel gas
and carbon monoxide detector.
The California Safe Drinking Water and Toxic Enforcement Act requires the
Governor of California to publish a list of substances known to the State of
California to cause cancer, birth defects, or other reproduc ve harm, and
requires businesses to warn of poten al exposure to such substances.
WARNING! This product contains a chemical known to the State of California
to cause cancer, birth defects, or other reproduc ve harm.
This water heater can cause low-level exposure to some of the substances
included in the act.
*Drain and flush tank and remove and
inspect anode rod a er first six months
of opera on and at least annually
therea er. Operate the Temperature
and Pressure Relief Valve (T&P) annually and inspect T&P valve every 2-4
years (see the label on the T&P valve for
maintenance schedule). See the Maintenance sec on for more informa on
about maintaining this water heater.
Residen al Standard Gas Water Heater Use and Care Guide • 3
SAFETY
IMPORTANT SAFETY INFORMATION
SAFETY
IMPORTANT SAFETY INFORMATION
T
o reduce the risk of property
damage, serious injury or death,
read and follow the precau ons below,
all labels on the water heater, and
the safety messages and instruc ons
throughout this manual.
RISKS DURING
INSTALLATION AND
MAINTENANCE
Li ing Risk
WARNING! The
water heater is heavy.
Follow these precauons to reduce the
risk of property damage, injuries from
li ing or impact injuries from dropping
the water heater.
•
Use at least two people to li the
water heater.
•
Be sure you both have a good grip
before li ing.
•
Use an appliance dolly or hand
truck to move the water heater.
Gas Pressure
WARNING! The gas supply pressure
must not exceed the maximum supply
pressure as stated on the water
heater’s data plate. The minimum
supply pressure is for the purpose of
input adjustment. L.P. gas supply
pressure must not exceed 13” water
column. Have a qualified person
(licensed plumber, gas company
personnel, or authorized service
technician) check for proper L.P. gas
pressure. L.P. gas pressures exceeding
13” water column can result in serious
injury or death from explosion or fire.
Table 1
RISKS DURING
OPERATION
Scalding Risk
This water heater
can make water hot
enough to cause severe burns instantly,
resul ng in severe injury or death.
•
•
Explosion Risk
WARNING! Read the water heater’s
data plate to determine the type of
gas required. Failure to follow these
instruc ons can result in serious injury
or death from explosion, fire or
carbon monoxide poisoning.
•
Do not connect a natural gas water
heater to an L.P. gas supply.
•
Do not connect an L.P. gas water
heater to a natural gas supply.
•
Use a new CSA approved gas
supply line.
•
Install a shut-off valve on the gas
supply line.
•
Feel water before bathing or
showering.
To reduce the risk of scalding,
install Thermosta c Mixing Valves
(temperature limi ng valves) at
each point-of-use. These valves
automa cally mix hot and cold
water to limit the temperature at
the tap. Follow manufacturer’s
instruc ons for installa on and
adjustment of the valves.
The gas control valve on this water
heater has been factory set to its
lowest se ng to reduce the risk
of scalding. Higher temperatures
increase the risk of scalding, but
even at 120°F, hot water can scald.
If you choose a higher temperature se ng, Thermosta c Mixing
Valves located at each point-of-use
are par cularly important to help
avoid scalding.
4 • Residen al Standard Gas Water Heater Use and Care Guide
Temperature
Time to Produce
a Serious Burn
120°F (49°C)
More than 5 minutes
125°F (52°C)
1½ to 2 minutes
130°F (54°C)
About 30 seconds
135°F (57°C)
About 10 seconds
140°F (60°C)
Less than 5 seconds
145°F (63°C)
Less than 3 seconds
150°F (66°C)
About 1½ seconds
155°F (68°C)
About 1 second
For informa on about changing the
factory temperature se ng, refer to
the “Adjus ng the Temperature” secon in this manual .
Even if you set the water heater’s gas
control valve to a low se ng, higher
water temperatures may occur in certain circumstances:
•
•
•
•
In some cases, repeated small draws
of water can cause the hot and cold
water in the tank to “stack” in layers.
If this happens, the water can be as
much as thirty degrees ho er than
the gas control valve se ng. This
temperature varia on is the result
of your usage pa ern and is not a
malfunc on.
Water temperature will be ho er if
someone adjusted the gas control
valve to a higher se ng.
Problems with the gas control valve
or other malfunc ons may result in
higher than expected water temperatures.
If the water heater is in a hot environment, the water in the tank can
become as hot as the surrounding
air, regardless of the temperature
se ng.
•
•
If the water supplied to the water
heater is pre-heated (for example,
by a solar system) the temperature
in the tank may be higher than the
water heater’s temperature se ng.
Should overhea ng occur or the
burner fail to shut off, turn off the
manual gas supply valve to the water
heater and call a qualified person.
To reduce the risk of unusually hot water reaching the fixtures in the house,
install Thermosta c Mixing Valves at
each point-of-use.
If anyone in your home is at par cular
risk of scalding (for example, the elderly, children, or people with disabili es)
or if there is a local code or state law
requiring a certain water temperature
at the hot water tap, these precau ons
are par cularly important.
According to a na onal standard (ASSE
1070) and many local plumbing codes,
the water heater’s gas control valve
should not be used as the sole means
to regulate water temperature and
avoid scalds.
Properly adjusted Thermosta c Mixing
Valves installed at each point-of-use allow you to set the tank temperature to
a higher se ng without increasing risk
of scalds. A higher temperature se ng
allows the tank to provide much more
hot water and can help provide proper
water temperatures for appliances such
as dishwashers and washing machines.
Higher tank temperatures (140°F)
also kill bacteria that cause a condion known as “smelly water” and can
reduce the levels of bacteria that cause
water-borne diseases.
Water Contamina on Risk
Do not use chemicals that could contaminate the potable water supply. Do
not use piping that has been treated
with chromates, boiler seal, or other
chemicals.
Fire Risk
This water heater is
equipped with a Flammable Vapor Igni on
Resistance (FVIR) system.
FVIR is designed to reduce the risk of
flammable vapor-related fires. FVIR
makes this product more sensi ve to
installa on errors or improper installaon environments. The FVIR system will
not prevent a possible fire/explosion if
the igniter is depressed and flammable
vapors have accumulated in the combuson chamber with the pilot light off.
Do not a empt to light this appliance,
or depress the igniter bu on, if you
suspect flammable vapor have accumulated inside or outside the appliance.
Immediately call a qualified person to
inspect the appliance. Water heaters
subjected to a flammable vapors incident will show a discolora on on the
flame arrestor and require replacement
of the en re water heater. Improper
installa on or an inadequate air supply
can also cause the FVIR system to disable the water heater.
WARNING! This water heater has a
rese able thermal switch installed as
part of the FVIR system. Do not
a empt to disable or modify this
feature in any way. Doing so can lead
to fire, explosion or excessive and
abnormal produc on of carbon
monoxide.
To reduce the risk of a fire that could
result in property damage, or serious
injury or death:
•
•
Do not store things that can burn
easily such as paper or clothes next
to the water heater.
Do not store or use gasoline or other
flammable substances in the vicinity
of this or any other appliance.
•
Keep the water heater from becoming wet. Immediately shut the water
heater off and have it inspected by a
qualified person if you find that the
wiring, thermostat(s) or surrounding insula on have been exposed
to water in any way (e.g., leaks from
plumbing, leaks from the water
heater itself can damage property
and could cause a fire risk). If the
water heater is subjected to flood
condi ons or the thermostat(s) have
been submerged in water, the en re
water heater must be replaced.
•
Replace the water heater’s viewport
if glass is missing or damaged. Repair
the combus on chamber door seals
if damaged.
Explosion Risk
High temperatures and
pressures in the water
heater tank can cause an explosion resul ng in property damage, serious injury or death. A new Temperature and
Pressure (T&P) Relief Valve is included
with your water heater to reduce risk
of explosion by discharging hot water.
Addi onal temperature and pressure
protec ve equipment may be required
by local codes.
A na onally recognized tes ng laboratory maintains periodic inspec on
of the valve produc on process and
cer fies that it meets the requirements
for Relief Valves for Hot Water Supply
Systems, ANSI Z21.22. The T&P Relief
Valve’s relief pressure must not exceed
the working pressure ra ng of the water heater as stated on the ra ng plate.
Maintain the T&P Relief Valve properly.
Follow the maintenance instruc ons
provided by the manufacturer of the
T&P Relief Valve (label a ached to T&P
Relief Valve). An explosion could occur
Residen al Standard Gas Water Heater Use and Care Guide • 5
SAFETY
IMPORTANT SAFETY INFORMATION
SAFETY
IMPORTANT SAFETY INFORMATION
if the T&P Relief Valve or discharge
pipe is blocked. Do not cap or plug the
T&P Relief Valve or discharge pipe.
instruc ons. When the installa on is
complete, check the vent’s dra using
the instruc ons on pages 23-24.
Fire and Explosion Risk if Hot Water is
Not Used for Two Weeks or More.
•
Install a fuel gas and carbon monoxide detector in the living areas
of your home.
CAUTION! Hydrogen gas builds up
in a hot water system when it is not
used for a long period (two weeks or
more). Hydrogen gas is extremely
flammable. If the hot water system
has not been used for two weeks or
more, open a hot water faucet for
several minutes at the kitchen sink
before using any electrical appliances
connected to the hot water system. If
hydrogen is present there will
probably be an unusual sound such as
“air” escaping through the pipe as hot
water begins to flow. Do not smoke or
have an open flame or other igni on
source near the faucet while it is
open.
•
Do not install this water heater in
a mobile home or manufactured
housing.
•
Failure to follow these instrucons can result in serious injury
or death from carbon monoxide
poisoning.
Installa on Accessories
Figure 1 - Gas Water Heater Hook-Up Kit
Burn Risk
This water heater’s venting system can become
hot enough to burn. Do not touch the
ven ng system while water heater is
on, or un l the water heater is turned
off and the ven ng allowed to cool.
Carbon Monoxide Risk
WARNING! This water heater
operates by burning gas. Carbon
monoxide is a colorless, odorless, gas
that is a by-product of burning of fuels
such as coal, wood, charcoal, oil,
kerosene, propane, and natural gas.
Breathing excessive and abnormal
amounts of carbon monoxide can
cause carbon monoxide poisoning,
resul ng in serious injury or death.
This water heater must be supplied
with adequate combus on air and
must be properly
vented to the
outdoors. Have a
qualified person
(licensed plumber,
authorized gas
company personnel, or authorized
service technician) install the ven ng
system using these installa on
6 • Residen al Standard Gas Water Heater Use and Care Guide
Figure 2 - Install a Pressure Reducing Valve set
to 50 to 60 PSI.
GETTING STARTED
This water heater is designcer fied by CSA Interna onal
as a Category I, non-direct
vented water heater which takes its
combus on air either from the installaon area or from air ducted to the unit
from the outside. This water heater
must be installed according to all local
and state codes or, in the absence of
local and state codes, the “Na onal
Fuel Gas Code”, ANSI Z223.1(NFPA
54)-current edi on. This is available
from the following:
2
CSA America, Inc.
8501 East Pleasant Valley Road
Cleveland, OH 44131
Na onal Fire Protec on Associa on
1 Ba erymarch Park
Quincy, MA 02269
Check with local code officials about
codes governing this installa on. Have
your installa on inspected by a code
official to ensure the installa on meets
all local codes.
NOTICE: If you lack the necessary skills
required to properly install this water
heater, or you have difficulty following the instruc ons, you should not
proceed but have a qualified person
perform the installa on of this water
heater.
Massachuse s code requires this water
heater to be installed in accordance
with Massachuse s 248-CMR 2.00 and
248-CMR 5.00: State Plumbing Code.
Other local and state authori es may
have similar requirements or other
codes applicable to the installa on of
this water heater.
3
Before you start, be sure you
have the following tools and
supplies:
•
Common plumbing tools (depending on what type of water pipes
you have).
• Teflon® tape or pipe joint compound approved for potable water.
• For homes with copper pipes, you
may purchase a Gas Water Heater
Hook-Up Kit (available at your local
plumbing supplier) with compression fi ngs that don’t require
soldering. This kit includes two 12”
flex water lines, two compression
fi ngs, an 18” flexible gas line, two
nipples, and Teflon® tape.
• For homes with plas c pipe, use
threaded connectors suitable for
the specific type of plas c pipe
used: CPVC or PEX (cross-linked
polyethylene). Do not use PVC
pipe.
• Non-corrosive gas leak detec on
solu on made from hand dishwashing soap mixed with water (1
part soap to 15 parts water) or children’s soap bubbles and a small,
so -bristled brush.
• An appliance dolly or hand truck to
move the water heater.
Recommended Accessories:
•
•
•
•
•
•
A metal drain pan.
Automa c water leak detec on
and shut-off device.
Pressure Reducing Valve.
Thermal Expansion Tank.
Thermosta c Mixing Valves at each
point-of-use.
Fuel gas and carbon monoxide
detector.
Combus on and
Ven la on Air Supply
Before installing the water heater, you
must determine the amount of air
needed to supply this water heater
and any other gas appliances in the
same area and provide adequate air for
combus on and ven la on. Consult a
qualified person if you’re unsure of the
proper way to supply air to your water
heater.
WARNING! This gas water heater
requires an adequate source of clean
air for combus on and ven la on.
Without sufficient air, your water
heater will have frequent pilot outages
and may emit excessive and abnormal
amounts of carbon monoxide.
Before beginning:
Calculate total BTU/HR ra ng of all appliances.
To calculate the combus on air and
ven la on required, add up the total
BTU/HR ra ngs of all gas burning appliances (e.g., water heaters, furnaces,
clothes dryers) in the same area.
Your water heater’s BTU/HR ra ng is on
the data plate, located next to the gas
control valve/thermostat. The BTU/HR
ra ngs should be on the other appliances’ data plates. If you have trouble
determining the BTU/HR ra ngs,
contact the manufacturer or have a
qualified person determine the ven laon requirements. NOTICE: If you are
replacing your old water heater with
one that has a higher BTU/HR ra ng,
the amount of ven la on required may
be greater.
Residen al Standard Gas Water Heater Use and Care Guide • 7
GETTING STARTED
Review all of the instruc ons
before you begin work.
Improper installa on can
damage the water heater, your home
and other property, and can present
risks of serious injury or death.
1
GETTING STARTED
Example:
GETTING STARTED
Gas Burning Appliance
BTU/HR Ra ng
Gas Water Heater
40,000
Furnace
75,000
Dryer
20,000
Total
135,000
Your Appliances:
Gas Burning Appliance
BTU/HR Ra ng
Gas Water Heater
Total
Table 2 provides examples of minimum
square footage (area) required for
various BTU/HR totals. Areas used for
storage or which contain large objects
containing less air than is assumed for
the room sizes in Table 2 – see Op on
A for more specific calcula ons.
Op on A: Installa on without
outside ven la on (not recommended)
Ven la on with outside air is recommended for all installa ons. Even if
the water heater is installed in a large,
open room inside the house, outdoor
air is usually needed because modern
homes are very ghtly sealed and
o en do not supply enough air to the
water heater. However, when installed
in a large indoor space, it may be possible to provide enough air without
outside ven la on. If you are unsure if
your installa on loca on has enough
ven la on, contact your local gas
u lity company or code officials for a
safety inspec on.
The following instruc ons will help determine if it may be possible to install
without outside ven la on. Even if
this may be possible, you will need to
conduct the vent dra test on pages
23-24 when installa on is finished. If
there is not enough ven la on, you
will need to ven late with outside air.
Table 2
BTU/HR
Input
Minimum Square
Feet with 8’ Ceiling
Typical Room
with 8’ Ceiling
30,000
188
9 x 21
45,000
281
14 x 20
60,000
375
15 x 25
75,000
469
15 x 31
90,000
563
20 x 28
105,000
657
20 x 33
120,000
750
25 x 30
135,000
844
28 x 30
8 • Residen al Standard Gas Water Heater Use and Care Guide
Check for Chemicals:
Installa ons where corrosive chemicals may be present require outside
air. Air for combus on and ven la on
must be clean and free of corrosive or
acid-forming chemicals such as sulfur,
fluorine, and chlorine. Ven la on with
outside air will reduce these chemicals,
but it may not completely eliminate
them. Failure due to corrosive chemicals is not covered by the warranty.
Examples of loca ons that require
outside air due to chemicals include:
•
Beauty salons
•
Photo processing labs
•
Indoor pools
•
Laundry, hobby, or cra rooms
•
Chemical storage areas
Products such as aerosol sprays, detergents, bleaches, cleaning solvents,
gasoline, air fresheners, paint and
varnish removers, and refrigerants
should not be stored or used near the
water heater.
A1: Calculate the air volume of
the room
Air requirements depend on the size of
the room.
Floor Area (Square feet) X Ceiling
Height (feet) = Room Volume (cubic
feet)
If there are large objects in the room
(e.g., refrigerator, furnace, car), subtract their volume from the volume of
the room to get a be er es mate of
the air available.
Room Volume – Object Volume = Air
Volume
GETTING STARTED
A water heater installed in an unconfined
a c or garage requires that the space
be at least 50 cubic feet per 1,000 BTU/
HR of the total input for all gas burning
appliances in the same area.
[Total BTU/HR/1000] x 50 = Cubic feet
of air required.
Example:
(135,000 / 1000) x 50 = 6,750
If the air volume of the room is less
than the required air volume, you must
provide two permanent outside air
openings that draw in sufficient air. Use
Op on B.
mum free area is sized according to Table
3. Two openings must be used when
ven la ng with air from another room.
The outside air can be taken from a
crawl space or a c open to the outdoors and adequately ven lated. You
may use ver cal or horizontal ducts.
B2: Determine type of ven laon
There are several types of ven la on
that can be used :
1.
2.
3.
4.
If the air volume of the room is greater
than the required air volume, it may
be possible to install the water heater
without outside ven la on.
A3: Check that combus on venla on is adequate
Because modern homes are o en wellsealed to prevent dra s, even a large
room may not provide enough combuson air without ven la on. To confirm that your installa on has enough
combus on air, conduct the vent dra
test on pages 23-24 when installa on is
finished.
Op on B: Install with outside
ven la on
Ven la on with outside air is recommended, and, for most installa ons, is
needed. There may be exis ng ven laon that is adequate, or you may need
to add more ven la on.
Supplying outside air to typically requires
two openings. One opening must be
within 12 inches from the floor and
the second opening must be within 12
inches from the ceiling. Although a single
opening is not preferred, you may use a
single opening to outside air if the mini-
5.
Direct to outdoors
Ver cal ducts
Horizontal ducts
Single opening (not recommended; must be at least 100
square inches. Not appropriate
for confined spaces smaller than
50 cubic feet per 1,000 BTU/HR as
calculated in sec on A or when
ge ng air from another room.)
From a larger room inside the
house (not recommended – refer
to sec on A above to determine if
the combined volume of the rooms
may be adequate).
B3: Determine minimum free
area required for each vent
opening
The size of the vent openings depends
on the total BTU/HR ra ng of all appliances in the space (use your calcula on
from “Before beginning”) and the type
of vent used. Table 3 provides the minimum free area for each vent opening
depending on the type of ven la on.
B4: Calculate minimum size of
vent openings and ducts
The vent cross-sec onal area needed to
provide the free area depends on the
covering on the vent openings. Typical
vents use louvers or grilles to protect
the opening. The louver or grill itself
blocks some of the free area, so the
opening may need to be larger to meet
the minimum free area requirements.
Use the following formula to calculate
the required cross-sec onal area:
Cross-sec onal area = minimum free
area required ÷ percent free area of
Table 3
Minimum Free Area of Permanent Openings for Ven la on and Combus on Air
Supply – All Air from Outdoors Only.
Based on the total BTU/HR input ra ng for all gas burning appliances within a
confined space.
Opening Source
Minimum Free Area
Per Opening (sq. in.)
*Direct to outdoors
1 sq. in. per 4,000 BTU/HR (see figure on page 10)
Ver cal ducts
1 sq. in. per 4,000 BTU/HR (see figure on page 10)
Horizontal ducts
1 sq. in. per 2,000 BTU/HR (see figure on page 10)
Single Opening
1 sq. in. per 3,000 BTU/HR (see figure on page 10)
*These openings connect directly with the outdoors through a ven lated a c, a
ven lated crawl space, or through an outside wall.
Residen al Standard Gas Water Heater Use and Care Guide • 9
GETTING STARTED
A2: Calculate required air volume
GETTING STARTED
GETTING STARTED
covering (in decimals – e.g., 60% = .6)
For example, an installa on area that
requires openings with 100 square
inches of free area would need 134
square inch openings if using metal
louvers rated at 75% free area (100 sq.
in. ÷ .75 = 134 sq. in.).
If you do not know the % free area for
your louver or grill, use the following
values:
•
For wood louvers or grilles: 20%
•
For metal louvers or grilles: 60%
Follow these rules to ensure that vents
and ducts provide adequate air flow:
•
Each vent opening must be no
smaller than 100 square inches .
•
Ducts must have the same crosssec onal area as free area of the
opening.
•
Rectangular ducts must have a
minimum dimension of no less
than three inches .
•
All screens must have mesh ¼” or
larger.
•
Moveable louvers must be locked
open or interconnected with the
equipment so that they open automa cally during opera on.
•
Keep louvers and grills clean and
free of debris or other obstrucons.
B5: Check that air source is
clean and free of chemicals
Air for combus on and ven la on
must be clean and free of corrosive
or flammable chemicals. A failure due
to corrosive chemicals in the air is not
covered by the warranty. Combuson air must be free of acid-forming
chemicals such as sulfur, fluorine, and
chlorine. Be sure that air at the vent
inlets is free of such chemicals.
Figure 5 - Horizontal duct openings
B6: Check that combus on
ven la on is adequate
To confirm that your installa on has
enough combus on air, conduct the
vent dra test on pages 23-24 when
installa on is finished.
Combus on Air Supply Op ons
Figure 6 - Single opening
Figure 3 - Direct to outdoors openings
Figure 4 - Vertical duct openings
10 • Residen al Standard Gas Water Heater Use and Care Guide
Ven ng
Installing a New Vent System
WARNING! Carbon Monoxide
Hazard. This water heater must be
supplied with adequate air and vented
to outdoors. The vent system must be
installed by a qualified person.
Examples of a qualified person include
gas technicians, authorized gas
company personnel, and authorized
service technicians. Failure to properly
vent the water heater can result in
severe injury or death from carbon
monoxide poisoning.
The vent pipe must meet the following
specifica ons:
The vent system must be installed
according to local and state codes, or
in the absence of local or state codes,
the current edi on of the Na onal Fuel
Gas Code, ANSI Z223.1 (NFPA 54). Do
not common vent this water heater
with any power vented appliance. Do
not use a vent damper anywhere in the
vent system of this water heater.
To reduce the risk of carbon monoxide
poisoning, install a fuel gas and carbon
monoxide detector. Install and maintain
the detector in accordance with the
manufacturer’s instruc ons and local
codes.
Replacing a Water Heater Using
the Exis ng Vent System
Read the “Installing a New Vent System” sec on of this manual and make
sure your vent system is properly installed. Inspect the exis ng vent system
for obstruc ons, corrosion, and proper
installa on. Repair or replace if necessary. The exis ng vent system must be
UL listed Type B double wall or single
wall metal vent pipe of either 3 inch or
4 inch diameter and installed according
to the vent manufacturer’s instruc ons
and the terms of its lis ng. Do not use
other materials such as dryer vent hose.
Type of Material
UL listed Type B double wall or single
wall metal vent pipe must be used.
Local codes may be more restric ve
and may not allow single wall vent pipe.
Single-wall vent pipe cannot be used for
water heaters located in a cs and may
not pass through a c spaces, crawl
spaces, or any confined or inaccessible
loca on. Single-wall vent pipe cannot
pass through any interior wall.
Clearance to Combus ble Materials
The vent pipe cannot pass through any
ceiling, floor, firewall, or fire par on.
Any part of the vent system must maintain the following clearances from any
combus ble materials:
•
Single-wall vent pipe must maintain a six inch clearance from
combus ble materials.
•
The clearance from combus ble
materials of UL listed Type B double-wall vent pipe is specified by
the manufacturer of the vent pipe.
UL listed Type B double-wall vent
pipe may pass through walls or parons constructed of combus ble
material if the minimum clearance
specified by the manufacturer of
the vent pipe is maintained.
Vent Installa on
To improve the flow of exhaust gases,
we recommend that a minimum of 12
inches of ver cal vent pipe be installed
on the dra hood prior to any elbow.
A por on of the vent pipe (up to 75%
of the total ver cal height) can be
horizontal, but the termina on must
be ver cal. For the horizontal sec on,
install without dips or sags with an
upward slope of at least ¼ inch per
foot. Install pipe avoiding unnecessary
bends. Pipe joints must be fastened by
sheet metal screws or other approved
means. Support the pipe to maintain
clearances and to avoid separa on of
joints or other damage. Vent pipe must
be accessible for cleaning, inspec on,
and replacement.
Termina ons
If local codes allow, this water heater
may be terminated into an exis ng
chimney using the instruc ons below.
Otherwise, this water heater’s vent
must terminate ver cally (sidewall or
other horizontal termina ons are not
allowed).
Chimney Termina on
Figure 7 - Chimney termination vent system
NOTICE: Before connec ng a vent to
a chimney, make sure the chimney
passageway is clear and free of obstrucons. The chimney must be cleaned if
previously used for ven ng solid fuel
appliances or fireplaces. Also consult local and state codes for proper chimney
sizing and applica on or, in the absence
of local and state codes, the “Na onal
Fuel Gas Code”, ANSI Z223.1(NFPA
54)-current edi on.
•
The vent pipe must be installed
above the extreme bo om of the
chimney to prevent poten ally
blocking the flue gases.
Residen al Standard Gas Water Heater Use and Care Guide • 11
GETTING STARTED
GETTING STARTED
GETTING STARTED
GETTING STARTED
•
The vent pipe must be firmly attached and sealed to prevent it
from falling out.
•
To aid in removing the vent pipe, a
thimble or slip joint may be used.
•
The vent pipe must not extend
beyond the inner edge of the
chimney as it may restrict the
space between it and the opposite
wall of the chimney.
Ver cal Termina on
NOTICE: The gas vent must be terminated in a ver cal posi on to facilitate
the removal of exhaust gases.
Ver cal exhaust vents must terminate
with a listed cap or other roof assembly and be installed according to their
manufacturer’s instruc ons. An unused
chimney flue or masonry enclosure
may be used as a passageway for the
installa on of vent pipe. Do not common vent this water heater with any
power vented appliance. The following figures are examples of vent pipe
system installa ons and may or may
not be suitable for your specific applica on. Consult the “Na onal Fuel Gas
Code”, NFPA 54, ANSI Z223.1-current
edi on and local codes.
Install a readily accessible manual
shut-off valve in the gas supply line
as recommended by the local u lity. Know the loca on of this valve
and how to turn off the gas to this
unit.
2.
Install a Sediment Trap as shown
in the Gas Piping figure below. The
Sediment Trap must be no less than
three inches long for the accumulaon of dirt, foreign material, and
water droplets.
3.
Install a ground joint union between the gas control valve and
the manual gas shut-off valve. This
is to allow easy removal of the gas
control valve.
4.
Turn the gas supply on and check
for leaks. Use a small, so -bristled
brush to apply a hand dishwashing soap and water mixture (1
part soap to 15 parts water) or
children’s soap bubbles to all connec on points of the gas piping.
Saturate all the connec ons and
check for gas leaks (which will appear as small bubbles). If any leaks
are detected, ghten the appropriate connec on(s) and re-check.
Figure 8 - Vertical gas vent system with type B
double wall vent pipe
Do not terminate the vent pipe in a
chimney that has not been cer fied
for this purpose. Some local codes may
prohibit the termina on of vent connectors in a masonry chimney.
Common (combined) ven ng is allowable with ver cal Type B vent systems
and lined masonry chimneys as long
as proper dra for the water heater
is established under all condi ons of
opera on. Do not common vent this
water heater with any power vented
appliance.
1.
Figure 9 - Venting through a chimney with type
B double wall vent pipe
Gas Piping
Gas piping must be installed according to local and state codes or, in the
absence of local and state codes,
the “Na onal Fuel Gas Code”, ANSI
Z223.1(NFPA 54)-current edi on.
NOTICE: When installing gas piping,
apply pipe joint compound or Teflon®
tape approved for fuel gases.
Figure 10 - Gas Piping
12 • Residen al Standard Gas Water Heater Use and Care Guide
Gas Pressure
NOTICE: When tes ng gas pipes with
a test pressure of more than ½ psi (3.5
kPa), disconnect the gas line at the
manual shut off valve and cap the gas
line. Do not subject the water heater’s
gas control valve or manual shut off
valve to more than ½ psi (3.5 kPa)
pressure for any reason. If you are
pressure tes ng the gas line with test
pressure of ½ psi (3.5 kPa) or less, you
may isolate the water heater from the
gas line by closing the manual shut off
valve.
GETTING STARTED
Space Hea ng
TYPICAL MIXING VALVE INSTALLATION
COMBINATION SPACE HEATING / POTABLE WATER HEATING SYSTEM
EXPANSION TANK
TEMPERED WATER
TO FIXTURES
(MUST MEET TEMPS LISTED
IN MASS. CODE 248 CMR † )
CHECK
VALVE †
The domes c hot water line from the
water heater should be ver cal past
any mixing valve or supply line to the
air handler to remove air bubbles from
the system. Otherwise, these bubbles
will be trapped in the air handler heat
exchanger coil, reducing efficiency.
•
Do not connect the water heater to
any system or components previously
used with non-potable water heating appliances when used to supply
potable water.
COLD WATER INLET
CHECK VALVE †
(1/8” HOLE
DRILLED IN CLAPPER)
VACUUM
RELIEF
VALVE
•
SHUT-OFF
VALVE
FLOW CONTROL
VALVE
UNION
HOT
WATER
OUT
WATER HEATER ACCEPTED
BY THE BOARD FOR
INSTALLATION IN
MASSACHUSETTS. †
*
PUMP *
TEMP/
PRESSURE
RELIEF
VALVE
MUST BE VERTICAL TO
REMOVE AIR BUBBLES
MIXING VALVE
(MUST BE INSTALLED BELOW
TOP OF WATER HEATER
AS PER MANUFACTURER’S
RECOMMENDATIONS)
UNION
OUT
COIL
TO
AIR
HANDLER
SEE
NOTE ‡
SHUT-OFF
VALVE *
IN
AIR
HANDLER
100’-0” MAXIMUM DISTANCE
FROM WATER HEATER †
TO FAN COIL AND BACK
(DEVELOPED LENGTH) NOT
INCLUDING COIL IN HEATING UNIT.
MASSACHUSETTS INSTALLATION REQUIREMENTS:
1.) CONNECT ELECTRONICALLY-CONTROLLED TIMER TO AN ALL-BRONZE PUMP. PUMP MUST ACTIVATE EVERY 6 HOURS
FOR 60 SECONDS. TURN PUMP TIMER OFF BEFORE CLOSING PIPING LOOP SHUT-OFF VALVE.
2.) ALL WATER PIPING MUST BE INSTALLED AND INSULATED IN ACCORDANCE WITH MASSACHUSETTS CODE (248 CMR
& 780 CMR).
3.) PIPING LOOP BETWEEN WATER HEATER AND AIR HANDLER MUST BE INSTALLED IN COMPLIANCE WITH 248 CMR.
†
REQUIRED FOR MASSACHUSETTS.
‡
PIPING FROM THE TOP OF THE WATER HEATER WITH TEES IS ACCEPTABLE.
Figure 11 - Combustion Space Heating and Potable Water (Typical Installation)
Some water heater models are equipped
with inlet/outlet connec ons for use with
space hea ng applica ons. If this water
heater is to be used to supply both space
hea ng and domes c potable (drinking)
water, the instruc ons listed below must
be followed.
•
Do not use with piping that has been
treated with chromates, boiler seal or
other chemicals and do not add any
chemicals to the water heater piping.
•
If the space hea ng system requires
water temperatures in excess of 120°F,
install a Thermosta c Mixing Valve
in the domes c (potable) hot water
supply at each point-of-use to limit the
risk of scald injury. Install the mixing
valve per its manufacturer’s instrucons.
•
This water heater is suitable for
combina on water (potable) hea ng
and space hea ng and not suitable for
space hea ng applica ons only.
•
Be sure to follow the manual(s)
shipped with the air handler system.
•
This water heater is not to be used as
a replacement for an exis ng boiler
installa on.
Pumps, valves, piping, and fi ngs
must be compa ble with potable
water.
•
A properly installed flow control valve
is required to prevent thermosiphoning. Thermosiphoning is the result of a
•
Solar Installa on
If this water heater is used as a solar storage heater or as a backup for the solar
system, the water supply temperatures
to the water heater tank may be in excess
of 120°F. A Thermosta c Mixing Valve or
other temperature limi ng valve must be
installed in the water supply line to limit
the supply temperature to 120°F. The unit
must be set to Standard Mode (See Operating Modes in Opera on sec on on page
24).
NOTICE: Solar water hea ng systems can
o en supply water with temperatures
exceeding 180°F and may result in water
heater malfunc on.
Residen al Standard Gas Water Heater Use and Care Guide • 13
GETTING STARTED
con nuous flow of water through the
air handler circuit during the off cycle.
INSTALLATION
Step 1:
✓
INSTALLATION
Verify that your
home is equipped
and up-to-date for
proper opera on
Installing a new water heater is the
perfect me to examine your home’s
plumbing system and make sure the
system is up to current code standards. There have likely been plumbing code changes since the old water
heater was installed. We recommend
installing the following accessories
and any other needed changes to
bring your home up to the latest code
requirements. Upda ng your plumbing system can help extend the life of
your water heater, avoid damage to
your home and property, and reduce
the risk of serious injuries or death.
Inspect your home and install any devices you need to comply with current
codes and assure that your new water
heater performs at its best. Check
with your local plumbing official for
more informa on.
✓
Water pressure
Most codes allow a maximum
incoming water pressure of 80 psi
(we recommend a working pressure
no higher than 50-60 psi). Check your
home’s water pressure with a pressure
gauge and adjust if necessary. High
water pressure can damage the water
heater, piping, and other appliances.
HOW: Purchase an inexpensive water
pressure gauge at your local plumbing
supplier. Connect the water pressure
gauge to an outside faucet and measure the maximum water pressure
experienced throughout a 24-hour
period (highest water pressures o en
occur at night).
✓
Water pressure
increase caused
by thermal expansion
Verify that you have a properly sized
Thermal Expansion Tank. We recommend installing an expansion tank if
your home does not have one. Plumbing codes require a properly pressurized, properly sized Thermal Expansion Tank in almost all homes.
Figure 12 - Use a Water Pressure Gauge to make
sure your home’s water pressure is not too
high.
To adjust your home’s water pressure:
Locate your home’s Pressure Reducing Valve (PRV) on the main incoming
(cold) water supply line and adjust the
water pressure control to between
50 and 60 psi. If your home does not
have a Pressure Reducing Valve, install
a PRV on the home’s main water
supply line and set it to between 50
and 60 psi. Pressure Reducing Valves
are available at your local plumbing
supplier.
BACKGROUND: Over the years,
many u li es have increased water
supply pressures so they can serve
more homes. In some homes today,
pressures can exceed 100 psi. High
water pressures can damage water
heaters, causing premature leaks. If
you have replaced toilet valves, had
a water heater leak, or had to repair
appliances connected to the plumbing system, pay par cular a en on
to your home’s water pressure. When
purchasing a PRV, make sure the PRV
has a built-in bypass.
14 • Residen al Standard Gas Water Heater Use and Care Guide
Figure 13 - A Thermal Expansion Tank helps
protect the home’s plumbing system from pressure spikes.
HOW: Connect the Thermal Expansion Tank (available at most hardware
stores.) to the cold water supply line
near the water heater. The expansion
tank contains a bladder and an air
charge. To work properly, the Thermal
Expansion Tank must be sized according to the water heater’s tank capacity
and pressurized to match the home’s
incoming water pressure. Refer to
the instruc ons provided with the
Thermal Expansion Tank for installaon details.
BACKGROUND: Water expands when
heated, and the increased volume
of water must have a place to go, or
thermal expansion will cause large
INSTALLATION
A Thermal Expansion Tank is a prac cal and inexpensive way to help avoid
damage to the water heater, washing
machine, dishwasher, ice maker, and
even toilet valves. If your toilet occasionally runs for no apparent reason
(usually briefly at night), that may be
due to thermal expansion increasing
the water pressure temporarily.
✓
Water Pipe and
Tank Leaks
• Install an automa c leak detecon and shutoff device (available at
your local plumbing supplier). These
devices can detect water leaks and
can shut off the water heater’s water
supply if a leak occurs.
• Install a metal drain pan (available at
your local plumbing supplier) under
the water heater to catch condensaon or leaks from the piping connecons or tank. Most codes require,
and we recommend, installing the
water heater in a metal drain pan
that is piped to an adequate drain.
The drain pan must be at least two
inches wider than the diameter of
the water heater. Install the drain
pan so the water level would be limited to a maximum depth of 1-3/4”.
The pan must not restrict air flow to
the burner.
✓
Water Temperature Regula on
Figure 15 - Thermostatic Mixing Valves installed
at each point-of-use can help avoid scalding
BACKGROUND: A Thermosta c Mixing
Valve, installed at each point-of-use,
mixes hot water from the water heater
with cold water to more precisely
regulate the temperature of hot water
supplied to fixtures. If you aren’t sure
if your plumbing system is equipped
with properly installed and adjusted
Thermosta c Mixing Valves at each
point where hot water is used, contact
a qualified person.
Install Thermosta c Mixing Valves to
regulate the temperature of the water
supplied to each point-of-use (for
example, kitchen sink, bathroom sink,
bath, shower). Install and adjust the
mixing valve according to its manufacturer’s instruc ons.
WARNING! Even if the water
heater’s thermostat is set to a relavely low temperature, hot water can
scald. Install Thermosta c Mixing
Valves at each point-of-use to reduce
the risk of scalding.
Figure 14 - A metal drain pan piped to an adequate drain can help protect flooring from leaks
and drips.
Leaks from plumbing pipes or from the
water heater itself can damage property and could cause a fire risk.
Residen al Standard Gas Water Heater Use and Care Guide • 15
INSTALLATION
increases in water pressure (despite
the use of a Pressure Reducing Valve
in the home’s main water supply line).
The Safe Drinking Water Act of 1974
requires the use of backflow preventers and check valves to restrict water
from your home reentering the public
water system. Backflow preventers are
o en installed in water meters and
may not be readily visible. As a result,
most all plumbing systems today are
now “closed,” and almost all homes
now need a Thermal Expansion Tank.
INSTALLATION
Step 2:
Verify that the loca on
is appropriate
INSTALLATION
WARNING! Do not store or use
flammable materials, vapors, or
liquids in the same loca on where this
water heater is installed.
Before installing your water heater,
ensure that it will be located:
• Indoors in an area with adequate
air supply.
• In an area that will not freeze.
• As close as possible to a chimney
or vent.
• In a metal drain pan piped to an
adequate drain.
• In an area suitable for ver cal
installa on.
• In an area with adequate space
(clearances) for periodic servicing
(there must be a minimum of 24
inches of front clearance).
• In an area that allows a minimum
clearance from combus ble surfaces as stated on the data plate.
• On a floor that can support the
weight of a water heater full of
water.
You will also want to follow these
guidelines while considering an appropriate loca on:
• Do not install near air-moving
devices such as exhaust fans,
ven la on systems, or clothes
dryers.
• Do not obtain ven la ng air for
the furnace/air handler from the
same space as the water heater.
Ensure that any return air ducts
near the water heater are sealed.
• If the water heater is located
in an area subject to lint, dust,
or oily vapors, at least annually
check and clean the air filter. See
Maintenance sec on for steps on
cleaning the air filter.
• Do not install in a bathroom,
bedroom, or any occupied room
normally kept closed.
• If the water heater is installed directly on carpe ng, it shall be installed on a metal or wood panel
extending beyond the full width
and depth of the water heater
by at least 3 in (76.2mm) in any
direc on. If the water heater is
installed in an alcove or closet,
the en re floor shall be covered
by the aforestated panel.
• If your area is prone to earthquakes, use special straps as
required by local building codes.
NOTICE: The state of California requires bracing, anchoring, or strapping the water heater to avoid its
moving during an earthquake. Contact
local u li es for code requirements in
your area, visit h p://www.dsa.dgs.
ca.gov, or call 1-916-445-8100 and
request instruc ons. Other loca ons
may have similar requirements. Check
with your local and state authori es.
•
Do not install in a loca on prone
to physical damage by vehicles,
flooding, or other risks.
Vehicle
Stop
Drain
Pan
Drain
Figure 16 - In a garage, install a vehicle stop to
avoid water heater damage.
16 • Residen al Standard Gas Water Heater Use and Care Guide
•
Avoid loca ons such as a cs, upper floors, or where a leak might
damage the structure or furnishings. Due to the normal corrosive
ac on of water, the tank will
eventually leak. To minimize property damage from leaks, inspect
and maintain your water heater
in accordance with this manual’s
instruc ons. Install a metal drain
pan under the water heater piped
to an adequate drain. Inspect the
drain pan, pipes, and surrounding
area regularly and fix any leaks
found.
Step 3:
Removing the old
water heater
Read each installa on step and
decide if you have the necessary skills to install the water
heater. Only proceed if you are comfortable you can safely perform the work. If
you are not sure, have a qualified person
perform the installa on.
1
INSTALLATION
2
On the old water heater, turn
the control knob on the gas
control valve to the
OFF posi on.
drain, outside, or in buckets. (Sediment in the bo om of the tank may
clog the valve and prevent it from
draining. If you can’t get the tank to
drain, contact a qualified person.)
Turn the cold water supply
valve OFF.
6
Figure 21 - Removing the T&P Relief Valve
discharge pipe.
Gas
control
knob
3
4
Turn the manual gas valve for
the water heater’s supply line
OFF.
Open a hot water faucet and
let the hot water run un l it is
cool (This may take 10 min
utes or longer).
Figure 19 - Cold water supply in off position.
Using a standard flat-blade
screwdriver, open the drain
valve. Sediment build up in
the bo om of the water heater may
hinder or prevent draining.
INSTALLATION
Figure 17 - Turn gas control/temperature knob OFF.
Allow the vent pipe and dra
hood to cool. Once cooled,
disconnect the vent pipe from
the dra hood. You may need to
support the vent pipe un l the new
water heater is in place.
10
7
Figure 22 - Disconnect the vent pipe from the
draft hood.
Disconnect the water pipes.
Many water pipes are connected by a threaded union
which can be disconnected with
wrenches. If you must cut the water
pipes, cut the pipes close to the water
heater’s inlet and outlet connec ons,
leaving the water pipes as long as
possible. If necessary, you can make
them shorter later when you install the
new water heater.
11
Figure 20 - Draining the old water heater.
Also open a hot water faucet
to help the water in the tank
drain faster.
When the tank is empty,
disconnect the Temperature &
Pressure (T&P) Relief Valve
discharge pipe. You may be able to
reuse the discharge pipe, but do not
reuse the old T&P Relief Valve. A new
T&P Relief Valve comes with your new
water heater.
8
Figure 18 - Let the hot water run until it is cool.
WARNING! Be sure the water runs
cool before draining the tank to reduce
the risk of scalding.
5
Connect a garden hose to the
drain valve and place the
other end of the hose in a
9
12
Confirm the manual gas valve
for the water heater’s supply
Residen al Standard Gas Water Heater Use and Care Guide • 17
INSTALLATION
line is turned off. Disconnect the gas
line from the water heater’s gas
control valve and cap it.
13
Remove the old water heater.
Use an appliance dolly or
hand truck to move the water
heater.
WARNING! Use two or more
people to remove or install a water
heater. Failure to do so can result in
back or other injury.
Step 4:
Installing the New
Water Heater
Completely read all instrucons before beginning. If you
are not sure you can safely
complete the installa on, seek assistance from any of the following sources:
• Schedule an appointment with
a qualified person to install your
water heater.
• Call our Technical Assistance Hotline
at 1-800-527-1953.
INSTALLATION
1
2
Install a metal drain pan that
is piped to an adequate drain.
base that extends beyond the dimensions of the water heater (width and
depth) by at least 3 inches (76.2 mm)
in any direc on. If the water heater is
installed on carpet in an alcove or
closet, the en re floor must be covered
by a wood or metal panel.
NOTICE: Most codes require se ng
the water heater in a metal drain pan
piped to an adequate drain. The drain
pan helps avoid property damage
which may occur from condensa on
or leaks in the piping connec ons or
tank. The drain pan must be at least
two inches wider than the diameter
of the water heater. Install the drain
pan so the water level is limited to a
maximum depth of 1-3/4”.
Verify that the water heater is
set in place properly. Check
that:
• There is adequate space to install
the T&P Relief Valve discharge
pipe and that it can be piped to a
separate drain (and not into the
drain pan).
• There is adequate access and
space around the water heater
for future maintenance.
The water heater is installed ver cally.
4
Step 5:
Air Filter
Figure 23 - Metal drain pan piped to drain.
This water heater is equipped with a
base-ring air filter. Before proceeding
to the next step, visually check the
filter to ensure it is properly seated
in the base-ring. Do not operate the
water heater without the a clean air
filter in place.
Set the water heater in place
taking care not to damage the
drain pan. When installing
directly on carpet, the water heater
must be installed on a wood or metal
3
18 • Residen al Standard Gas Water Heater Use and Care Guide
Figure 24 - Filter attached to water heater.
INSTALLATION
Step 7:
Step 6:
Install Shutoff and Thermosta c Mixing Valves
Connect the Temperature and Pressure (T&P)
Relief Valve/Pipe
Figure 26 - Temperature and Pressure Relief
Valve Pipe
•
•
Figure 25 - Temperature and Pressure Relief Valve
WARNING! To avoid serious injury
or death from explosion, install a T&P
Relief Valve according to the following
instruc ons:
If the T&P Relief Valve was not
factory installed, install the
new T&P Relief Valve that
came with your water heater. Do not
reuse an old T&P Relief Valve.
• The discharge pipe should be at
least 3/4” inside diameter and
sloped for proper drainage. Install
it to allow complete drainage of
both the T&P Relief Valve and the
discharge pipe.
1
•
The discharge pipe must not be
smaller than the pipe size of the
T&P Relief Valve. The pipe must
also be able to withstand 250°F
(121°C) without distor on. Use
only copper or CPVC pipe. Do not
use any other type of pipe, such as
PVC, iron, flexible plas c pipe, or
any type of hose.
Terminate the discharge pipe a
maximum of six inches above a
floor drain or outside the building.
Do not drain the discharge pipe
into the drain pan; instead pipe it
separately to an adequate drain.
In cold climates, terminate the discharge pipe inside the building to
an adequate drain. Outside drains
could freeze and obstruct the
drain line—protect the discharge
pipe from freezing.
Do not place any valve or other
restric on between the tank and
T&P Relief Valve. Do not cap,
block, plug, or insert any valve
between the T&P Relief Valve and
the end of the discharge pipe. Do
not insert or install any reducer in
the discharge pipe.
2
INSTALLATION
Most T&P Relief Valves are preinstalled at the factory. In some cases,
they are shipped in the carton and
must be installed in the opening
marked “T&P Relief Valve” and according to local codes.
If one is not already installed,
install a manual shutoff valve
in the cold water line that
supplies the water heater. Install the
shutoff valve near the water heater so
that it is readily accessible. Only use a
full-flow ball or gate valve compa ble
with potable water.
Install a Thermosta c Mixing
Valve at each point-of-use (for
example, kitchen sink,
bathroom sink, bath, shower) per the
valve manufacturer’s instruc ons.
1
Figure 27 - Install Thermostatic Mixing Valves at
each point where hot water will be used.
WARNING! Even if the water
heater’s thermostat is set to a relavely low temperature, hot water can
scald. Install Thermosta c Mixing
Valves at each point-of-use to reduce
the risk of scalding.
Residen al Standard Gas Water Heater Use and Care Guide • 19
INSTALLATION
For water heaters that are fed
by a solar water hea ng
system (or any other prehea ng system), always install a
Thermosta c Mixing Valve or other
temperature limi ng device in the
inlet water supply line to limit water
supply inlet temperature to 120°F.
Solar water hea ng systems can
supply water with temperatures
exceeding 180°F and may result in
water heater malfunc on.
3
IF YOU HAVE COPPER PIPES:
If your home has copper water pipes,
you can solder the water pipe connecons or use compression fi ngs which
don’t require soldering. Compression
fi ngs are easier to install than soldering pipe. Check with local plumbing
officials to determine what types of
pipe materials are suitable for your
loca on. Do not use lead-based solder.
INSTALLATION
WARNING! Hot water provided by
solar hea ng systems can cause
severe burns instantly, resul ng in
severe injury or death.
Compression fi ngs don’t require soldering.
NOTICE: Do not solder pipes while
they are a ached to the water heater.
The water heater’s inlet and outlet
Step 8:
Connect the Water
Supply
Note that all piping and components
connected to the water heater must
be suitable for use with potable water.
Determine the type of water
pipes in your home. Most
homes use copper water
pipes, but some use CPVC or crosslinked polyethylene (PEX). Use fi ngs
appropriate for the type of pipe in
your home. Do not use iron or PVC
pipe.
1
20 • Residen al Standard Gas Water Heater Use and Care Guide
connec ons contain non-metallic parts
which could be damaged. The proper
way to connect the water heater to
copper water pipes is as follows:
• Solder a short length of pipe (about
a foot or so) to a threaded adapter
using only 95/5 n-an mony or
equivalent solder. A ach the threaded adapters to the water heater’s
connec ons (using Teflon® tape or
pipe joint compound). Connect the
home’s water pipes by soldering,
keeping the connec ons at the water
heater cool with wet rags.
Connect the cold water
supply using 3/4 inch
Na onal Pipe Thread “NPT” to the
fi ng marked “C” (COLD).
2
For ease of removing the water heater
for service or replacement, connect the water pipes with a coupling
called a union. We recommend using
a dielectric-type union (available at
your local plumbing supplier). Dielectric unions can help prevent corrosion caused by ny electric currents
common in copper water pipes and
can help extend the life of the water
heater
INSTALLATION
NOTICE: Most water heater models
contain energy saving heat traps in the
inlet and outlet connec ons. Do not
remove the heat traps.
Connect the hot water supply
using 3/4 inch NPT to the
fi ng marked “H” (HOT).
Install insula on (or heat
tape) on the water pipes
especially if the indoor
installa on area is subject to freezing
temperatures. Insula ng the hot water
pipes can increase energy efficiency.
Step 10:
Install Dra Hood
4
Adjust (or install) the home’s
Pressure Reducing Valve to
50-60 psi and install a Thermal
Expansion Tank.
5
Install the new dra hood by
aligning the legs and inser ng
them into the slots provided on
top of the water heater. Do not reuse the
dra hood from the old water heater,
but rather use the new one that came
with your new water heater.
1
Figure 29 - The Thermal Expansion Tank should
be pressurized with air, using a hand pump, to
match the home’s incoming water pressure.
Step 9:
Verify Connec ons and
Completely Fill Tank
To remove air from the tank and allow
the tank to fill completely with water,
follow these steps:
Secure the dra hood using
the four screws provided.
A ach the home’s exis ng vent
pipe to the dra hood outlet using an
approved vent adapter (not supplied).
2
Remove the aerator at the
nearest hot water faucet. This
allows debris in plumbing
system to be washed out of the pipes.
1
2
Figure 28 - A Pressure Reducing Valve is required
if your home’s water pressure is above 80 psi.
3
Turn the cold water supply
back on and fill the tank.
Open a hot water faucet and
allow the water to run un l it
flows with a full stream.
4
Let the water run full stream
for three minutes.
5
Close the hot water faucet
and replace the aerator.
Figure 30 - Install the new draft hood and secure
with screws.
Secure the vent adapter to the
dra hood with sheet metal
screws. Read the Ven ng
sec on on page 11. Make sure your
home’s ven ng system complies with
the instruc ons in this manual and is in
good condi on.
3
Residen al Standard Gas Water Heater Use and Care Guide • 21
INSTALLATION
3
Check inlet and outlet connecons and water pipes for leaks.
Dry pipes connec ons so that
any drips or leaks will be apparent.
Repair any leaks. Almost all leaks occur
at connec ons and are not a tank leak.
6
INSTALLATION
Step 11:
Make Gas Connec ons
INSTALLATION
The Gas Water Heater Hook-Up Kit
(available at your local plumbing supplier) includes a flexible gas connector
with compression fi ngs to connect
the home’s gas line to the water
heater’s gas control valve. Follow the
kit’s installa on instruc ons to a ach
the flexible gas connector.
surfaces maintained and sufficient
room to service the water heater.
✓ Not installed directly on a carpeted
Once you’ve made the gas connecons, use a small, so -bristled brush
to apply a hand dishwashing soap
and water mixture or children’s soap
bubbles (1 part soap to 15 parts water)
to all connec on points of the gas line
and flexible gas connector (if used).
Make sure to generously coat all the
connec ons and check for gas leaks
(which will appear as small bubbles).
If any leaks are detected, turn the gas
supply off, ghten the leaking connecon and re-check.
BEFORE LIGHTING THE WATER
HEATER...
Make sure all checklist items have
been completed.
Water Heater Loca on
✓ Installa on area free of corrosive
or flammable materials, liquids or
vapors.
✓ Proper clearances from combus ble
✓ Check exis ng vent system for rust,
restric ons/obstruc ons.
floor.
✓ Metal drain pan installed and piped
to an adequate drain.
✓ Water heater not located near an
air moving device (fan, clothes
dryer).
✓ Not in a loca on with large
amounts of lint, dust, etc. (If so,
the air filter or flame arrestor
located on the bo om of the water
heater will need to be cleaned
more o en.)
Combus on Air Supply and
Ven la on
✓ Adequate air supply for water
Figure 31 - Flexible gas line connector.
Z223.1(NFPA 54)-current edi on.
heater and any other nearby gas
appliances.
If the water heater is installed in a
closet or other small, enclosed space
or within the living space of the
house, air supply openings needed.
✓ Are the openings of sufficient size?
✓ Ductwork is the same cross-seconal area as the openings?
✓ Outside air openings are preferred
and may be required in ghtly built
homes.
Vent Pipe System
✓ New dra hood, properly installed.
✓ Vent pipe securely fastened to
dra hood with screws and supported properly.
✓ Vent pipe made of approved material and either 2” or 3” in diameter.
✓ Vent system installed according
to local and state codes or, in the
absence of local and state codes,
the “Na onal Fuel Gas Code”, ANSI
22 • Residen al Standard Gas Water Heater Use and Care Guide
Water System Piping
✓ Temperature and pressure relief
valve properly installed with a
discharge line run to an adequate
drain and protected from freezing.
✓ Water pipes free of leaks.
✓ Water heater completely filled with
water.
✓ Thermal Expansion Tank installed
✓ Water Pressure Reducing Valve
installed and adjusted to 50-60 psi.
✓ Thermosta c Mixing Valves installed at each point-of-use.
Gas Supply and Piping
✓ Gas type is the same as that listed
on the water heater’s data plate.
✓ Gas line equipped with shut-off
valve.
✓ Adequate gas pipe size and approved gas pipe material.
✓ All gas connec ons and fi ngs leak
checked and any leaks corrected.
OPERATION
WARNING! Explosion Hazard –
Replace viewport if glass is missing or
damaged. Failure to do so can result
in death, explosion or fire.
Read and understand these direc ons
thoroughly before a emp ng to light
or re-light the pilot. Make sure the
viewport is not missing or damaged.
Make sure the tank is completely filled
with water before ligh ng the pilot.
Check the data plate near the gas
control valve to ensure the correct gas
type. Do not use this water heater with
any gas other than the one listed on the
data plate. If you have any ques ons or
doubts, consult your gas supplier or gas
u lity company.
NOTICE! A newly installed water heater
will have air in the gas line. It may take
several ligh ng a empts to clear all the
air from the gas line and light the pilot.
Follow these steps to light the pilot:
1
Make sure the manual gas
valve for the water heater’s
supply line is ON.
Press the gas control knob in
fully and hold it in. While
holding in the gas control
knob, repeatedly click the igniter bu on
(approximately once per second) for up
to 90 seconds or un l the Status Light
starts to flash. You can tell the pilot is lit
when the Status Light flashes once
every three seconds.
3
Turn the gas control/temperature knob
counterclockwise to the “OFF” se ng.
The status light will stop blinking and stay
on for a short me a er the water heater
is turned off.
Figure 34 - Status light.
Emergency Shut down
Once the Status Light starts
flashing, release the gas
control knob. Adjust the gas
control knob to the desired temperature se ng.
Should overhea ng occur or the gas
supply fail to shut off, turn off the water
heater’s manual gas control valve and call
a qualified person.
4
If the Status Light doesn’t start
flashing a er 90 seconds,
release the gas control knob
and wait 10 minutes.
Repeat ligh ng steps 2 through
5 at least two addi onal mes
or un l the Status Light starts
flashing once every three seconds. Wait
10 minutes between ligh ng a empts.
6
2
Turn the gas control knob to
the PILOT posi on.
A solid Status Light means the
pilot was lit but is now off.
Release the gas control knob
and wait 10 minutes. Once the Status
Light goes out, repeat ligh ng steps 2
through 5.
7
If the Status Light doesn’t start
flashing a er three ligh ng
a empts, turn the gas control
knob to the OFF posi on and refer to
the “Troubleshoo ng-No Hot Water”
sec on (see page 25).
8
Figure 33 - Gas control/valve.
The air filter at the bo om of
the water heater must be
cleaned from me to me. See
the Maintenance sec on for steps on
cleaning the air filter. If the air filter is
not cleaned as needed, the water
heater’s pilot may go out.
10
Shut down Instruc ons
5
Figure 32 - Gas valve in “on” position
water heater. You may hear drips or a
sizzling sound when the water heater is
first lit or, you may see a small puddle on
the floor. Condensa on is not a leak and
will go away once the tank reaches
normal opera ng temperature.
9
When a gas water heater is first
lit and the tank is cold, condensa on o en forms inside the
Checking the Vent
System and Air Supply
Once the water heater is lit and the gas
control knob is set to the desired temperature, the burner will light (if the tank is
cold). Perform an air supply and vent test
to make sure the unit is ven ng properly
and the air supply is adequate:
The main burner must be on
for this test. With a newly
installed water heater full of
cold water, turning the temperature
control knob to HOT should cause the
main burner to come on. You can view
the burner through the sight glass at
the base of the water heater.
1
Close all windows and doors
and turn on all gas appliances
and air-moving devices (range
hoods, bathroom exhaust fans, ceiling
fans, etc.) in your home. Also, close any
fireplace dampers.
2
Residen al Standard Gas Water Heater Use and Care Guide • 23
OPERATION
Ligh ng Instruc ons
OPERATION
Allow the water heater’s main
burner to operate for five
minutes. Pass a newly ex nguished match approximately one inch
from the dra hood’s relief opening.
Smoke from the match should be
steadily drawn into the opening indicating the water heater is ge ng adequate
air and the vent system is working.
3
Temperature Control
System
Adjus ng the Temperature
With the installa on steps completed,
you may adjust the water heater’s temperature se ng if desired.
Set the gas valve to the desired
temperature. The “HOT”
se ng sets the water temperature to approximately 120°F,
reducing the risk of scald injury. You
may wish to set a higher temperature to
provide hot water for automa c
dishwashers or laundry machines, to
provide more hot water capacity, and to
reduce bacterial growth. Higher tank
temperatures (140° F) kill bacteria that
cause a condi on known as “smelly
water” and can reduce the levels of
bacteria that cause water-borne
diseases.
1
Figure 35 - Test the air supply and vent to make
sure the water heater has adequate air and is
venting properly.
If the main burner has been
opera ng for five minutes but
the match smoke dri s around
or is blown away from the opening, turn
the gas control knob OFF. Inspect the
vent system and repair if necessary. In
many cases, failure to pass the air
supply and vent test indicates the water
heater is not ge ng enough air or there
is a problem with the vent system. It
may be necessary to increase the air
supply by ge ng air from outside (see
page 7).
OPERATION
4
WARNING! Burn Hazard. Do not
touch the vent, doing so can cause
burns. If the dra hood does not draw
in smoke from a match a er five
minutes of main burner opera on,
shut the gas supply off, and do not
operate the water heater un l the vent
system and air supply have been
checked by a qualified person and
repaired if necessary. Con nuing to
operate the water heater in this
condi on could lead to serious injury
or death from carbon monoxide
poisoning.
Water usage pa erns, as well as heat
from sources such as solar collectors,
ambient air, and the pilot light can
result in temperatures higher than the
thermostat set-point.
WARNING! Higher temperatures
increase the risk of scalding, but even at
120°F, hot water can scald (see Table 1).
Install Thermosta c Mixing Valve(s) at
each point-of-use to reduce the risk of
scalding.
2
To adjust the water heater’s
thermostat:
Figure 36 - Adjust the gas control knob to “HOT”.
Turn the gas control knob on the gas
control valve to the right to the following se ngs.
• “A”
128°F
24 • Residen al Standard Gas Water Heater Use and Care Guide
• “B”
138°F
• “C”
147°F
• “VERY HOT” 160°F
NOTICE: The temperatures above are
approximates. The actual temperature
of the heated water may vary.
Wait for the water to heat up.
If you have no hot water a er
two hours, refer to the
Troubleshoo ng Sec on (see page 25).
3
NOTICE: If the tank is full of cold water,
condensa on may form inside the
water heater. This condensa on may
drop on the burner causing a sizzling
sound. In some cases, you may see a
small puddle on the floor. Condensaon is normal and should go away once
the tank reaches its normal opera ng
procedure.
WARNING! If you have increased
the temperature se ng and the
Thermosta c Mixing Valves are not set
properly (or not installed) you could
scald yourself while checking the
temperature.
Check water temperature at
several points of use in your
home (for example, bathtub
faucet, shower, or lavatory sink) and
adjust the Thermosta c Mixing Valves
as needed. If you aren’t sure how to
adjust the Thermosta c Mixing Valve
se ngs, or aren’t sure if you have
Thermosta c Mixing Valves, contact a
qualified person.
4
Opera ng Modes
The gas control valve has two different opera ng modes: Standard and
Vaca on. The Standard mode allows
you to adjust the water temperature
to your desired se ng. The Vaca on
(VAC) mode sets the thermostat at
approximately 55°F and is recommended when not using hot water for
an extended period of me. The VAC
se ng also reduces energy losses and
TROUBLESHOOTING
No Hot Water
Use the following step-by-step plan
as a guide to help determine why you
have no hot water:
1
Check the Status Light
The Status Light on the gas
control valve flashes once every three
seconds if the pilot is lit and the gas
control valve has not detected any
problems.
3
Checking the Pilot Light
Check the spark igniter. Dim
the room lights and look through the
viewport while clicking the igniter
bu on.
If you don’t see a spark through the
viewport, check to make sure the
igniter wire is firmly inserted into the
white connector.
If you see a spark, make sure the gas
supply valve is turned on, and try lighting the pilot using the ligh ng instrucons on page 23.
If the pilot s ll does not light, call a
qualified person.
Insufficient Hot Water
or Slow Hot Water
Recovery
Figure 37 - Status light.
If the Status Light is flashing once every three seconds and you have no hot
water, make sure the gas control knob
is set to HOT.
If the Status Light flashes more than
once every three seconds, refer to
the Status Light Code Troubleshoo ng
Chart on page 27.
WARNING! Because of the increased
risk from scalding, if you set the water
heater’s gas control knob higher than
120°F, install Thermosta c Mixing
Valves at each point-of-use. Due to the
increased risk of scalding, do not set the
temperature of the Thermosta c
Mixing Valves above 120°F.
If the hot water is simply not warm
enough, there are several possible
causes:
•
Faulty Thermosta c Mixing Valve
in a faucet or shower control
(check other faucets in the house
for hot water).
•
Water heater’s capacity too small
(or usage too high).
•
Reversed plumbing connec ons
or melted dip tube (usually found
soon a er new installa on).
•
Plumbing leak.
If you have tried ligh ng the pilot and the
Status Light does not flash, go to step 3.
•
Sediment or lime build up in the
bo om of the tank.
If the Status Light flashes, go to Step 1.
Thermosta c Mixing Valves. If the
If the Status Light is not flashing, go to
step 2.
2
Status Light is Not
Flashing
If the Status Light isn’t flashing, try
ligh ng the pilot using the ligh ng
instruc ons on page 23.
hot water is simply not warm enough,
make sure the faucet you are checking
doesn’t have a defec ve Thermosta c
Mixing Valve. Many shower controls
now have built-in mixing valves. If
these devices fail, they can reduce the
amount of hot water the shower or
faucet delivers even though there is
plenty of hot water in the tank. Always
check the water temperature at several
faucets to make sure the problem is not
in a faucet or shower control.
Undersized Water Heater. If your water
heater runs out of hot water quickly, it
may be too small for your needs. If the
water heater is old, consider replacing it
with a larger model. If the water heater
is in good condi on, you may be able
to meet your family’s hot water needs
with the exis ng water heater by installing Thermosta c Mixing Valves at each
point-of-use and then turning the gas
control knob to a higher se ng.
You can also reduce your home’s hot
water needs by washing clothes in cold
water, installing flow restrictors on
shower heads, repairing leaky faucets,
and taking other conserva on steps.
Reversed Connec ons or Melted Dip
Tube. Check the hot and cold water
connec ons and make sure your
home’s hot water pipe is connected
to the hot water outlet on the water
heater. Usually, reversed connec ons
are found soon a er the installa on
of a new unit. If copper pipes were
soldered while they were a ached to
the water heater, the dip tube may
have melted. The dip tube is a long,
plas c tube inside the tank a ached to
the cold water inlet. If the dip tube has
melted, it can be replaced by removing
the cold water inlet connec on, removing the old dip tube and installing
a new one.
Plumbing Leak. Even a small leak
in the hot water side of the home’s
Residen al Standard Gas Water Heater Use and Care Guide • 25
TROUBLESHOOTING
keeps the tank from freezing during
cold weather but can cause a Hydrogen
gas build up. See cau on on page 6.
TROUBLESHOOTING
plumbing system can make it appear
that the water heater is producing
li le to no hot water. In this case, the
burner will be on all or almost all the
me, yet you will have very li le hot
water. Locate and repair the leak.
Sediment or Lime in Tank. With an exis ng water heater, if you have some
hot water but not as much as you’re
used to, there may be a build up of
sediment or lime on the bo om of the
tank. Sediment or lime build up can
reduce the efficiency of your water
heater. Heavy deposits can damage
the water heater. See the Maintenance sec on for steps on draining
and flushing the water heater.
Temperature Too High
Adjust the thermostat on the water
heater to a lower se ng. Install or
adjust Thermosta c Mixing Valves
for each point-of-use (see the valve
manufacturer’s instruc ons).
TROUBLESHOOTING
Low Water Pressure
Check both the cold and hot water
at a sink to determine if the lower
pressure is only on the hot water side.
If both hot and cold faucets have low
pressure, call your local water u lity.
If the low pressure is only on the hot
water side, the primary causes are:
•
•
Melted heat traps or dip tube. Soldering copper pipes while they are
connected to the water heater can
melt the heat traps inside the hot
and cold water connec ons or the
dip tube (cold water side). Melted
heat traps or a melted dip tube
can restrict the flow of hot water.
If that’s the case, replace the heat
traps or dip tube.
Par ally closed supply valve. Open
the water heater’s supply valve fully.
Drips from T&P Relief
Valve Discharge Pipe
A small amount of water dripping
from the Temperature and Pressure
(T&P) Relief Valve usually means the
home’s water pressure is too high
and/or you need a Thermal Expansion Tank. See Step 1 in the Installaon sec on of this manual for more
informa on.
WARNING! When manually
opera ng the temperature-pressure
relief valve, make sure that no one is
in front of or around the discharge
outlet. The water may be extremely
hot and could cause severe burns.
Also ensure that the water discharge
will not cause property damage.
A large amount of hot water coming
from the T&P discharge pipe may be
due to the tank overhea ng. If the
T&P relief valve is discharging large
amounts of very hot water, turn the
gas supply valve off and call a qualified person.
If the water pressure is between 50
and 60 psi, a Thermal Expansion Tank
is installed and properly pressurized,
and the valve has been cleared of any
debris, and it s ll drips, the valve may
be broken—have a qualified person
replace the T&P Relief Valve.
WARNING! Do not cap or plug the
T&P Relief Valve or discharge pipe,
and do not operate the water heater
without a func oning T&P Relief
Valve—this could cause an explosion.
Water Odor
Water Pressure too High. High water
pressure can cause the T&P Relief
Valve to drip. Install a Pressure Reducing Valve (PRV) on the main cold
water supply line. Adjust the PRV to
between 50 and 60 psi.
Thermal Expansion Tank. Install a
Thermal Expansion Tank. If a Thermal
Expansion Tank is already installed
and the T&P Relief Valve discharge
pipe drips, the home’s water pressure
may be too high or the Thermal Expansion Tank may be defec ve. Refer
to the instruc ons that came with
the Thermal Expansion Tank for more
informa on.
Debris. In rare cases, debris can s ck
inside the T&P Relief Valve preven ng
the valve from sealing fully. In that
case, the T&P Relief Valve discharge
pipe will drip. You may be able to
clear debris from the T&P Relief Valve
by manually opera ng the valve,
allowing small quan es of water to
flush out the debris. See the label on
the T&P Relief Valve for instruc ons.
26 • Residen al Standard Gas Water Heater Use and Care Guide
Harmless bacteria normally present in
tap water can mul ply in water heaters and give off a “ro en egg” smell.
Although elimina ng the bacteria that
causes “smelly water” is the only sure
treatment, in some cases, the standard anode rod that came with your
water heater can be replaced with a
special zinc anode rod which may help
reduce or eliminate the odor. Contact
a qualified person.
NOTICE: To protect the tank, an anode
rod must be installed in the water
heater at all mes or the warranty is
void.
In cases where the “ro en egg” smell
is very strong, you could increase the
tank temperature to 140°F in order to
reduce bacterial growth in the tank.
WARNING! Because higher
temperatures increase the risk of
scalding, if you set the thermostat(s)
higher than 120°F, Thermosta c
Mixing Valves at each point-of-use
are par cularly important.
TROUBLESHOOTING
TROUBLESHOOTING
Residen al Standard Gas Water Heater Use and Care Guide • 27
MAINTENANCE
Rou ne Maintenance
Rou ne maintenance will help your
water heater last longer and work better. If you can’t perform these rou ne
maintenance tasks yourself, contact a
qualified person.
3
Open a hot water faucet and
let the hot water run un l it is
cool (This may take 10 min
utes or longer).
Remove and inspect the
anode rod and replace if
depleted. The anode rod
requires a 1-1/16” socket.
8
Draining and Flushing the
Water Heater
Tap water contains minerals that can
form sediment in the bo om of the
tank. The amount of sediment formed
depends on the hardness of your tap
water, the temperature se ngs, and
other variables. We recommend draining and flushing the water heater a er
the first six months of opera on to determine the amount of sediment build
up. If there is li le sediment, drain and
flush the tank annually. If there is a lot
of sediment, drain and flush the tank
more o en. Draining sediment extends
the life of the water heater.
To Drain and Flush the Tank:
1
Turn the gas control knob on
the gas control valve to the
OFF posi on.
Figure 41 - Let the hot water run until it is cool.
WARNING! Be sure the water runs
cool before draining the tank to
reduce the risk of scalding.
Connect a garden hose to the
drain valve and place the
other end of the hose in a
drain, outside, or in buckets. Note that
sediment in the bo om of the tank
may clog the valve and prevent it from
draining. If you can’t get the tank to
drain, contact a qualified person.
4
5
Turn the cold water supply
valve OFF.
6
Open the drain valve on the
water heater.
Figure 42 - Draining the water heater.
7
MAINTENANCE
Figure 40 - Turn gas control/temperature knob
OFF.
2
Also open a hot water faucet
to help the water in the tank
drain faster.
Turn the manual gas valve for
the water heater’s supply line
OFF.
28 • Residen al Standard Gas Water Heater Use and Care Guide
Figure 43 - Anode rods from new (top) to partially depleted (middle) to fully depleted stage
(bottom).
Anode Rod. The anode rod is a sacrificial metal rod that helps avoid corrosion and premature failure (leaks) in
the tank. The anode rod is a consumable item. Inspect the anode rod a er
the first six months of opera on when
you drain and flush the tank. Replace
the anode rod if it is substan ally worn
out or depleted. Therea er, inspect the
anode rod annually or more frequently
if needed. If you use a water so ener,
your anode rod will deplete faster than
normal. Inspect the anode rod more
frequently, replacing the anode rod if
it is depleted. Obtain a new anode rod
from your local plumbing supplier or
have a qualified person replace it. (Anode rods are a consumable item and
are not covered under warranty).
If a large amount of sediment
was present when the tank
was drained, flush the tank by
opening the cold water supply valve
and le ng the water run un l no more
sediment drains from the tank. Close
the drain valve when you are done.
9
MAINTENANCE
discharge pipe, turn the gas control
knob to the OFF posi on and call a
qualified person to determine the
cause.
Relight the pilot using the
instruc ons on page 23 and
adjust the gas control knob to
the desired temperature. It may take an
hour or more for the tank of cold water
to heat up.
11
Visual Inspec on
•
Figure 44 - Burner Flames
•
Leaking or damaged water and gas
piping.
•
Remove any flammable, corrosive
or combus ble materials near the
water heater.
If you lack the necessary skills required
to properly perform this visual inspecon or if the burner needs to be cleaned,
get help from a qualified person.
T&P Relief Valve Maintenance
On an annual basis, visually inspect the
ven ng and air supply system, piping
systems, main burner, pilot burner, and
the air filter.
Obstruc ons, damage, or deteriora on in the ven ng system. Make
sure the ven la on and combuson air supplies are not obstructed. Check the air filter for dust or
other debris and clean if needed.
•
Build up of soot and carbon on the
main burner and pilot burner. The
burner may be cleaned with soap
and hot water.
•
Inspect the burner flames through
the viewport and compare them
to the drawing below. A properly
opera ng burner should produce a
so blue flame. Blue ps with yellow
inner cones are sa sfactory. The ps
of the flame may have a slight yellow
nt. The flame should not be all
yellow or have a sharp blue-orange
color. Contaminated air may cause
an orange colored flame. Contact a
qualified technician if the flame is
not sa sfactory.
A dripping T&P Relief Valve is usually
caused by the home’s water pressure
being too high or the lack of a Thermal
Expansion Tank. If your T&P Relief Valve
drips, see page 26.
A T&P relief valve that has been allowed to drip for an appreciable period
of me should be inspected for mineral
buildup. See T&P relief valve tag for
more informa on.
Check the water heater for the following:
•
At least every five years, have a
qualified person inspect the T&P
Relief Valve and discharge pipe.
Damage caused by corrosive water
condi ons, mineral deposits, or
other problems can only be determined when a qualified person
removes and inspects the valve
and its components.
Figure 45 - T&P Relief Valve.
Read and follow the opera ng and annual maintenance instruc ons provided
by the manufacturer of the T&P Relief
Valve (yellow label a ached to T&P
Relief Valve). Minerals in the water can
form deposits that cause the valve to
s ck or create blocked passages, making the T&P Relief Valve inopera ve.
Follow these guidelines:
• At least annually, operate the T&P
Relief Valve manually to ensure the
waterways are clear and the valve
mechanism moves freely (above).
Before opera ng the valve manually,
check that it will discharge in a place
for secure disposal.
WARNING! Hot water will be
released. Before opera ng the T&P
relief valve manually, check that it will
discharge in a safe place. If water does
not flow freely from the end of the
Inspect and Clean the Air Filter
Figure 46 - Clean air filter periodically.
An air filter should be installed around
the base of the water heater. At least
annually inspect the air filter and check
for a build-up of dust or debris.
Vacuum the filter to remove any dust
or debris. If an oily residue is present
on the filter, wash it in soap and water,
then dry the filter.
Residen al Standard Gas Water Heater Use and Care Guide • 29
MAINTENANCE
Refill the tank by opening the
cold water supply valve. Make
sure a hot water faucet is open
and the drain valve is closed. Allow a
hot water faucet to run full for at least
three minutes to make sure the tank
has all the air removed and is completely full of water. Once you are certain the
tank is completely full of water, close
the hot water faucet.
10
MAINTENANCE
Removing and Replacing the
Gas Control Valve/Thermostat
gas control valve/thermostat. NOTE:
L.P. Gas systems use reverse (le -hand)
threads on the manifold tube.
IMPORTANT: The gas control valve/
thermostat is a standard valve with
wire leads that connect to a thermal
switch.
Removing the Gas Control Valve/
Thermostat:
Turn the gas control/temperature knob to the “OFF”
posi on.
Figure 56 - Gas control/valve with threaded pipe.
1
B
C
D
A
Figure 52 - Gas valve connections.
Disconnect the ground joint
union in the gas piping.
Disconnect the remaining
pipe from the gas control valve/
thermostat.
5
Figure 48 - Gas control/valve.
2
Turn off the gas at the
manual shut-off valve on the
gas supply pipe.
Replacing Gas Control Valve/Thermostat:
To replace the gas control valve/thermostat, reassemble in reverse order. When
replacing the gas control valve/
thermostat, thread a 4” sec on of gas
pipe into the inlet and use it to turn the
gas control valve/thermostat (clockwise.)
DO NOT OVER TIGHTEN, damage may
result.
• Be sure to use approved Teflon® tape
or pipe joint compound on the gas piping
connec ons and fi ng on
the back of the gas control valve that
screws into tank.
• Be sure to remove the pilot ferrule nut
from the new gas control valve/thermostat.
Figure 54 - Ground joint union connection.
Figure 50 - Gas valve in “off” position.
Drain the water heater. Refer
to the “Draining and Flushing
the Water Heater” sec on (see
page 28) and follow the procedure.
3
Disconnect the A igniter
wire from the igniter lead
wire. Use needle nose pliers
to disconnect the B red (+) and white
(-) thermopile wires. Disconnect C
pilot tube (7/16” wrench) and
D manifold tube (3/4” wrench) at the
MAINTENANCE
4
To remove the gas control
valve/thermostat, thread a 4”
sec on of gas pipe into the
inlet and use it to turn the FVIR Safety
System Opera onal Checklist TROUBLESHOOTING CHART gas control
valve/thermostat (counterclockwise.)
Do not use pipe wrench or equivalent
to grip body. Damage may result,
causing leaks. Do not insert any sharp
objects into the inlet or outlet connecons. Damage to the gas control valve/
thermostat may result.
6
30 • Residen al Standard Gas Water Heater Use and Care Guide
Figure 58 - Gas valve in “on” position.
• Turn the gas supply on and check for
leaks. Test the water heater by brushing
on an approved noncorrosive
leak detec on solu on. Bubbles forming
indicate a leak. Correct any leak found.
• Be sure tank is completely filled with
water before ligh ng and ac va ng the
water heater. Follow the
“Ligh ng Instruc ons” on page 23.
• If addi onal informa on is required,
contact the Service Department at:
1-800-527-1953
NOTES
NOTES
Residen al Standard Gas Water Heater Use and Care Guide • 31
NOTES
NOTES
32 • Residen al Standard Gas Water Heater Use and Care Guide
NOTES
NOTES
Residen al Standard Gas Water Heater Use and Care Guide • 33
NOTES
NOTES
34 • Residen al Standard Gas Water Heater Use and Care Guide
REPAIR PARTS
Replacement parts may be ordered through your plumber or
the local distributor. Parts will be shipped at prevailing prices
and billed accordingly.
NOTICE: When ordering replacement parts, have the following
informa on ready:
• Model and serial number
• Type of gas used
• Item number
• Parts descrip on
Legend
▲ Special anode rod (see page 26)
■ Temperature and Pressure Relief Valve is required but may
be factory installed
★ Unique: Flammable Vapor Igni on Resistant Safety System
parts
8
REPAIR PARTS LIST
Item
No.
Parts Description
1
DRAFT HOOD
2
REDUCER RING - SOME MODELS
(NOT SHOWN)
3
FLUE BAFFLE
(NOT SHOWN)
4
COMBINATION DIP TUBE/HEAT TRAP NIPPLE
5
HEAT TRAP/NIPPLE
6
ANODE ROD - SOME MODELS
7
COMBINATION HEAT TRAP NIPPLE/ANODE
- SOME MODELS
8
TEMPERATURE & PRESSURE RELIEF VALVE
(LOCATED TOP OR SIDE)
9
DRAIN VALVE
10
GAS CONTROL VALVE/THERMOSTAT
(with thermal switch wire lead)
11
OUTER DOOR
12
PILOT/THERMOPILE ASSEMBLY KIT
13
FINAL BURNER ASSEMBLY
14
MANIFOLD DOOR GASKET
15
BASE RING AIR FILTER
1
5
4
6
8
10
15
9
11
Residen al Standard Gas Water Heater Use and Care Guide • 35
REPAIR PARTS
7
REPAIR PARTS
Listed Parts Kits and Illustrations
Item 12: Pilot assembly kit, which contains the pilot assembly, thermopile, and retainer clip (Natural Gas or L.P.)
Item 13: Final burner assembly which contains the burner, orifice, manifold tube, gasket, door, pilot tube, thermopile,
manifold component block with retainer clip, thermal switch, and pilot assembly. (Natural Gas/Low Nox or L.P.)
REPAIR PARTS
Item 14: Contains manifold door gasket
Item #12
Item #13 (Natural Burner)
Item #13 (L.P. Burner)
Item #14
®Teflon is a registered trademark of E.I. Du Pont De Nemours and Company
A.O. Smith Corporation. All Rights Reserved.
Manufactured under license by American Water Heater Company, Tennessee.
Limited Warranty provided by Manufacturer.
36 • Residen al Standard Gas Water Heater Use and Care Guide

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement