Sharp XL-UH242 Operating instructions

Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
MICRO COMPONENT SYSTEM
XL-UH242 Micro Component System consisting of XL-UH242 (main unit)
and CP-UH242 (speaker system).
MODEL
XL-UH242
OPERATION MANUAL
Accessories
Please confirm that the following accessories are included.
Remote control 1 AM loop antenna 1
(RRMCGA081AWSA) (QANTL0010AWZZ)
Note:
This product is not compatible with MTP and AAC file systems.
Note:
Only the above accessories are included.
FM antenna 1
(92LFANT1535A)
XL-UH242
SPECIAL NOTES
DECLARATION OF CONFORMITY
Important Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Caution - use of controls or adjustments or performance
of procedures other than those specified herein may result in hazardous radiation exposure.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the National Electrical Code that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
2
SHARP MICRO COMPONENT SYSTEM, MODEL XL-UH242
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL : 1-800-BE-SHARP
For Business Customers : URL http://www.sharpusa.com
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
Note:
Licensed under one or more of U.S. Pat. 4,972,484, 5,214,678,
5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985,
5,740,317, 5,777,992, 5,878,080 or 5,960,037.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft, please record below the
model number and serial number which are located on the rear of the unit.
Please retain this information.
Model number
.......................................................
Serial number
.......................................................
Date of purchase .......................................................
Place of purchase.......................................................
03/12/17
XL-UH242 _2-10.fm
IMPORTANT SAFETY INSTRUCTIONS
be read before the product is operated.
2 Retain Instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on
a bed, sofa, rug, or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been
adhered to.
11 Power Sources - This product should be operated only from the type
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
6 Attachments - Do not use attachments not recommended by the prod-
12 Grounding or Polarization - This product may be equipped with a
5 Cleaning - Unplug this product from the wall outlet before cleaning.
uct manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
9 A product and cart combination should be moved with
13 Power-Cord Protection - Power-supply cords should be routed so
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
that they are not likely to be walked on or pinched by items placed
upon or against them.
14 Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has
used a replacement plug specified by the manufacturer that has the
same overload protection as the original plug.
Important Instruction
1 Read Instructions - All the safety and operating instructions should
XL-UH242
3
03/12/17
XL-UH242 _2-10.fm
XL-UH242
IMPORTANT SAFETY INSTRUCTIONS (continued)
15 Outdoor Antenna Grounding - If an outside antenna or cable system
19 Object and Liquid Entry - Never push objects of any kind into this
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
Important Instruction
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERV ICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
P OWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
16 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
17 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
18 Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
20 Servicing - Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22 Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
24 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25 Heat - The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
0304
4
03/12/17
XL-UH242 _2-10.fm
Contents
XL-UH242
Page
General Information
ENERGY STAR® Program Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 9
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 12
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Preparation for Use
CD or MP3/WMA disc Playback
To comply with the ENERGY STAR® standards mentioned above,
please cancel the demonstration mode, as described on page 12.
ENERGY STAR® is a U.S. registered mark.
Special Note
Supply of this product does not convey a license nor imply any right
to distribute content created with this product in revenue-generating
broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue-generating streaming applications (via Internet, intranets and/or other networks), other revenu-generating
content distribution systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact discs, digital versatile discs, semiconductor chips, hard drives,
memory cards and the like). An independent license for such use is
required. For details, please visit http://mp3licensing.com.
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . . . .16 - 18
Advanced CD or MP3/WMA disc playback . . . . . . . . . . . .19 - 20
Advanced CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
MP3/WMA folder mode (only for MP3/WMA files) . . . . . . .22 - 23
USB Memory Playback
Listening to USB mass storage device / MP3 Player . . .24 - 25
To remove USB memory device . . . . . . . . . . . . . . . . . . . . . . . . 25
Advanced USB playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Radio
Important Instruction
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the clock (Remote Control only) . . . . . . . . . . . . . . . . . 15
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 - 28
Advanced Features
Timer and sleep operation (Remote Control only) . . . . . .29 - 32
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . .33 - 34
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 - 36
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . .Back cover
5
03/12/17
XL-UH242 _2-10.fm
XL-UH242
Precautions
General
Please ensure that the equipment is positioned in a well-ventilated
area and ensure that there is at least 4" (10 cm) of free space
along the sides, top and back of the equipment.
4" (10 cm) 4" (10 cm)
Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
Do not remove the outer cover, as this
may result in electric shock. Refer
internal service to your local SHARP
service facility.
4" (10 cm)
General Information
4" (10 cm)
Use the unit on a firm, level surface free from
vibration.
POWER
ON/STANDBY
OPEN/
CLOSE
CD
TUNER
(BAND)
VIDEO
/AUX
USB
Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equipment (home computers, facsimiles, etc.)
which generate electrical noise.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures higher than
140˚F (60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and then
turn on your system.
In case of an electrical storm, unplug the
unit for safety.
This unit should only be used within the range of 41˚F - 95˚F
(5˚C - 35˚C).
Warning:
The voltage used must be the same as that specified on this unit. Using this product with a higher voltage other than that which is specified is dangerous and may result in a fire or other type of accident
causing damage. SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which
is specified.
Volume control
The sound level at a given volume setting depends on speaker efficiency, location and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on
with the volume control setting up high, or while continually listening
at high volumes.
6
03/12/17
XL-UH242 _2-10.fm
Controls and indicators
XL-UH242
Reference page
1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4. Disc or USB Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. Disc or USB Play or Repeat Button . . . . . . . . . . . . . . . 16, 20
6. Power ON/STANDBY Button . . . . . . . . . . . . . . . . . . . . . . . . 14
7. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
9. Video/Auxiliary/USB Button . . . . . . . . . . . . . . . . . . . . . . . . 33
10. USB Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
11. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
12. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
13. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16
14. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 16
General Information
Front panel
7
03/12/17
XL-UH242 _2-10.fm
XL-UH242
Controls and indicators (continued)
1
2
3
4
5
6 7
13 14
9 10 11
General Information
8
15
16
12
3
4
ANTENNA
FM
75 OHMS
GND AM
LEFT
AC INPUT
RIGHT
LEFT
SUBWOOFER
PRE-OUT
1
SPEAKERS
LIGHT-UP
LEFT RIGHT
SPEAKERS
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
Rear panel
Reference page
1. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. FM 75 Ohms Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . 11
4. AM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . 11
5. AM Loop Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Video/Auxiliary (Audio Signal) Input Jacks . . . . . . . . . . . . 33
7. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Speaker Light-up Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9. Subwoofer Pre-output Jack . . . . . . . . . . . . . . . . . . . . . . . . . 34
5
VIDEO/AUX IN
RIGHT
Display
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2. MP3/WMA Folder Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 23
3. MP3/WMA Title Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4. MP3 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8. MP3/WMA Total Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11. FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 27
12. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
13. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
14. Disc or USB Repeat Play Indicator . . . . . . . . . . . . . . . . 20, 26
15. Disc or USB Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . 18
16. Disc or USB Play Indicator . . . . . . . . . . . . . . . . . . . . . . 17, 26
6
7
8
Speaker system
1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Wire
1
3
9
2
2
4
8
03/12/17
XL-UH242 _2-10.fm
XL-UH242
2
7
8
9
11
15
12
16
13
17
14
18
10
19
3
20
21
22
23 24
4
5
6
25
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16
3. Disc Direct Search Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 19
4. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14
5. Extra Bass/Demo Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 14
7. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10. Video/Auxiliary/USB Button . . . . . . . . . . . . . . . . . . . . . . . . 24
11. Disc Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . 14, 21
12. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 26
13. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
14. USB Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
15. Memory Button . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 21, 28, 32
16. Disc/USB Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
17. Disc Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . 16, 20
18. USB Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . . . . 24
19. Tuning Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
20. CD Track Up or Fast Forward, Tuner Preset Up,
Time Up Button . . . . . . . . . . . . . . . . . . . 15, 23, 24, 28, 29, 32
21. CD Track Down or Fast Reverse, Tuner Preset Down,
Time Down Button . . . . . . . . . . . . . . . . 15, 23, 24, 28, 29, 32
22. Tuning Down Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
23. Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 24
24. Folder Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 24
25. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 15, 29, 32
General Information
Remote control
1
9
03/12/17
XL-UH242 _2-10.fm
XL-UH242
System connections
Make sure to unplug the AC power cord before any connections.
Antenna connection (see page 11)
FM antenna
AM loop antenna
Left speaker
Preparation for Use
Right speaker
ANTENNA
FM
75 OHMS
GND AM
VIDEO/AUX IN
RIGHT
LEFT
RIGHT
Speaker connection (see page 11)
LEFT
SUBWOOFER
PRE-OUT
AC INPUT
SPEAKERS
LIGHT-UP
LEFT RIGHT
SPEAKERS
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
AC outlet
(AC 120 V, 60 Hz)
AC power connection (see page 12)
10
03/12/17
XL-UH242 _2-10.fm
XL-UH242
Speaker connection
AM
75 OHMS
GND AM
VIDEO/AUX IN
RIGHT
LEFT
75 OHMS
AC INPUT
RIGHT
LEFT
SUBWOOFER
PRE-OUT
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
SPEAKERS
LIGHT-UP
LEFT RIGHT
SPEAKERS
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
< Assembling >
< Attaching to the wall >
Wall
GND AM
VIDEO/AUX IN
RIGHT
LEFT
SPEAKERS
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
AC INPUT
RIGHT
LEFT
RIGHT
LEFT
Red
Black
Do not stand or sit on the speakers. You may
be injured.
Incorrect
Preparation for Use
GND
ANTENNA
FM
ANTENNA
FM
75 OHMS
Caution:
Use speakers with an impedance of 6 ohms or more, as lower
impedance speakers can damage the unit.
Do not mistake the right and the left
channels. The right speaker is the one on the
SPEAKERS EDANCE:
AKER IMP
RATED SPE MS MIN.
6 OH
right side when you face the unit.
Do not let the bare speaker wires touch
each other.
Do not allow any objects to fall into or to be
LEFT
RIGHT
placed in the bass reflex ducts.
ANTENNA
FM
SPEAKERS
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
SPEAKERS
LIGHT-UP
LEFT RIGHT
Supplied AM loop antenna:
Connect the AM loop antenna to the AM and GND terminals. Position
the AM loop antenna for optimum reception. Place the AM loop
antenna on a shelf, etc., or attach it to a stand or a wall with screws
(not supplied).
Connect the black wire to the minus (-) terminal, and the red wire to
the plus (+) terminal.
SUBWOOFER
PRE-OUT
Antenna connection
Supplied FM antenna:
Connect the FM antenna wire to the FM 75 OHMS jack and position
the FM antenna wire in the direction where the strongest signal can
be received.
Speaker grilles are removable
Make sure nothing comes into contact
with the speaker diaphragm when you
remove the speaker grilles.
Screws (not supplied)
11
XL-UH242_11-19.fm
XL-UH242
System connections (continued)
AC power connection
Demonstration mode
After checking all the connections have been made correctly, plug
the AC power cord of this unit into the AC outlet. If you plug in the unit
first, the unit will enter the demonstration mode.
To cancel the demonstration mode:
When the unit is in the power standby mode (demonstration mode),
press the X-BASS/DEMO button.
The unit will enter the low power
consumption mode.
ANTENNA
FM
75 OHMS
GND AM
VIDEO/AUX IN
RIGHT
LEFT
Preparation for Use
RIGHT
LEFT
SUBWOOFER
PRE-OUT
AC INPUT
SPEAKERS
LIGHT-UP
LEFT RIGHT
SPEAKERS
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.
AC outlet
(AC 120 V, 60 Hz)
Note:
Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
Cooling fan:
The main unit is built with a cooling fan at the rear of the unit for
improved cooling. Please do not cover the opening of the fan with
any obstacles, as this will block proper ventilation.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to
select the extra bass mode.
Outdoor FM antenna
Use an outdoor FM antenna if you require better reception.
Consult your dealer.
ANTENNA
FM
ANTENNA
FM
75 OHMS
GND AM
RIGHT
RIGHT
LEFT
LEFT
Outdoor
FM antenna
75 OHMS
SPEAKERS
LIGHT-UP
LEFT
RIGHT
LEFT RIGHT
SUBWOOFER
PRE-OUT
ACINPUT
INPUT
AC
AM
LEFT
SPEAKERS
SPEAKERS
RATED
RATEDSPEAKER
SPEAKERIMPEDANCE:
IMPEDANCE:
66OHMS
OHMSMIN.
MIN.
GND
VIDEO/AUX IN
RIGHT
75 ohms
coaxial cable
Note:
When an outdoor FM antenna is used, disconnect the supplied FM
antenna wire.
12
XL-UH242_11-19.fm
Remote control
Battery installation
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
2
3
Open the battery cover.
Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
Close the cover.
XL-UH242
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
Keep the remote control away from moisture, heat, shock, and
vibrations.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Preparation for Use
Test of the remote control
Check the remote control after checking all the connections (see
pages 10 - 12).
Point the remote control directly at the remote sensor on the unit.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
Battery removal:
Open the battery cover and pull up the battery to take out.
13
XL-UH242_11-19.fm
XL-UH242
General control
Volume control
POWER
ON/STANDBY
Main unit operation:
When the VOLUME control is turned clockwise, the volume will
increase. When it is turned counterclockwise, the volume will
decrease.
Remote control operation:
Press the VOLUME (+ or -) button to increase or decrease the volume.
0 ..... 30 MAXIMUM
Basic Operation
Bass control
When the power is first turned on, the unit will enter the extra bass
mode which emphasizes the bass frequencies, and "X-BASS" will
appear. To cancel the extra bass mode, press the X-BASS/DEMO
button on the remote control.
To turn the power on
Press the ON/STAND-BY button to turn the power on.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
Illumination light control
When the power is turned on, ring around the volume control light
up. To turn on/off the light, hold down the CLEAR/DIMMER button
on the remote control for more than 2 seconds.
Volume auto fade-in
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
Equalizer
When the EQUALIZER MODE button is pressed, the current mode
setting will be displayed. To change to a different mode, press the
EQUALIZER MODE button repeatedly until the desired sound mode
appears.
FLAT
No equalization.
ROCK
For rock music.
CLASSIC
For classical music.
POPS
For pop music.
VOCAL
Vocals are enhanced.
JAZZ
For jazz.
14
XL-UH242_11-19.fm
Setting the clock (Remote Control only)
5
XL-UH242
Press the
or
button to adjust the hour and
then press the MEMORY button.
Press the
or
button once to advance the time by
1 hour. Hold it down to advance continuously.
Press the
or
button to adjust the minutes and
then press the MEMORY button.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
3
4
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to
select "CLOCK", and press the MEMORY button.
Press the
or
button to select 12-hour or 24hour display and then press the MEMORY button.
"AM 12:00"
"AM 0:00"
"0:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
Press the
or
button once to advance the time by
1 minute. Hold it down to change the time in 5-minute intervals.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.
[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to display the
time.
The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" does not
appear in step 3, step 4 (for selecting the 12-hour or 24-hour
display) will be skipped.
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 35 for details.]
2 Perform "Setting the clock" from step 1.
Basic Operation
6
15
XL-UH242_11-19.fm
XL-UH242
Listening to a CD or MP3/WMA disc
This system can play back a standard CD, CD-R/RW in the CD format
and CD-R/RW with MP3 or WMA files, but cannot record on them.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the device that was used for recording.
CD or MP3/WMA disc Playback
POWER
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3.
MP3 is a type of audio code which is processed by significant
compression from the original audio source with very little loss
in sound quality.
This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and
VBR files.
During VBR file playback, time counter in the display may differ
from its actual playback time.
Bitrate which is supported by MP3 is 32 ~ 320 kbps.
ON/STANDBY
CD
OPEN/
CLOSE
WMA:
WMA files are Advanced System Format files that include audio
files which are compressed with Windows Media Audio codec.
WMA is developed by Microsoft as an audio format file for
Windows Media Player.
"MP3" and "WMA" indicator will light up after the unit reads
information on an MP3 or WMA disc.
Bitrate which is supported by WMA is 64 ~ 160 kbps.
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit turns on and
the "CD" function is activated.
CD / button on the remote control: The unit turns on and CD
playback starts (regardless of the last function).
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TUNER,VIDEO/AUX/USB).
Auto power off function:
In the stop mode of CD, MP3 or WMA operation, the main unit enters
the stand-by mode after 15 minutes of inactivity.
16
XL-UH242_11-19.fm
XL-UH242
Press the ON/STAND-BY button to turn the power on.
4
Place the disc on the disc tray 1, label side up.
Be sure to place 3" (8 cm) disc in the middle of the disc trays.
Press the CD button.
Press the
1 button and within 5 seconds, press the
OPEN/CLOSE button to open the disc tray 1.
5" (12 cm)
3" (8 cm)
Playback will begin from track 1 on DISC 1. After that disc
finishes playing, the next disc will automatically play.
After the last track on the fifth disc is played, the unit will stop
automatically.
When there is no disc in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a disc.
To exchange other discs while playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5
seconds, press the OPEN/CLOSE button and exchange discs.
To remove the discs:
In the stop mode, press the 1 - 5 button and within 5 seconds,
press the OPEN/CLOSE button.
POWER
ON/STANDBY
OPEN/
CLOSE
CD
5
TUNER/
(BAND)
VIDEO/
AUX/USB
Press the
[CD]
OPEN/CLOSE button to close the disc tray 1.
TOTAL indicator
Total number of
Total playing
tracks on the disc time of the disc
MP3 indicator
WMA indicator
[MP3/WMA]
Total number
of files
Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
6
You can place discs on the trays 2 - 5 by following steps
3 - 5.
7
Press the
/
button to start playback.
To skip to a desired disc:
Press one of the 1 - 5 buttons and within 5 seconds, press the
(CD ) button.
Caution:
Do not place two discs in a same tray.
Do not play discs of special shapes (heart, octagon, etc).
It may cause malfunctions.
Do not push the disc tray while it is moving.
If the power fails while the tray is open, wait until the power is
restored.
If the disc tray is stopped with force, "ER-CD20" will appear on the
display for 3 seconds and the unit will not function. If this occurs,
press the ON/STAND-BY button to enter the power stand-by
mode and then turn the power on again.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
If a disc is damaged, dirty, or loaded upside down, the disc will be
skipped.
CD or MP3/WMA disc Playback
1
2
3
Disc play indicator
17
XL-UH242_11-19.fm
XL-UH242
Listening to a CD or MP3/WMA disc (continued)
Various disc functions
CD or MP3/WMA disc Playback
Function
Main unit
Remote
control
Operation
Play
Press in the stop
mode.
Stop
Press in the playback
mode.
Pause
Press in the playback
mode. Press the /
button to resume playback from the paused
point.
Press in the playback
or stop mode.
If you press the button
in the stop mode,
press the / button
to start the desired
track.
Track up/
Track down
Fast forward/Fast
reverse
Notes for CD or MP3/WMA disc:
Track up/track down is possible only within individual discs.
Fast forward/fast reverse is possible only within individual discs.
When the end of the last track is reached during fast forward,
"END" will appear on the display and CD operation will be paused.
When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
Rewritable multi session discs which writing is not finished, can
still be played.
Press and hold down
in the playback mode.
Release the button to
resume playback.
18
XL-UH242_11-19.fm
Advanced CD or MP3/WMA disc playback
Direct track search
By using the direct search buttons, the desired tracks on the current
disc can be played.
Use the direct search buttons on
the remote control to select the desired track while playing the selected disc.
XL-UH242
Notes:
A track number higher than the number of tracks on the disc cannot be selected.
During random play, direct search is not possible.
CD or MP3/WMA disc Playback
To stop playback:
Press the (CD ) button.
Selected track number
The direct search buttons allow you to select up to number 9.
When selecting number 10 or higher, use the "+10" button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "1" button.
3 Press the "3" button.
B. For example, to choose 130
1 Press the "+10" button twice.
2 Press the "1" button.
3 Press the "3" button.
4 Press the "0" button.
19
XL-UH242_11-19.fm
XL-UH242
Advanced CD or MP3/WMA disc playback (continued)
Repeat play
Repeat play can play one disc, all 5 discs or a programmed
sequence continuously.
CD or MP3/WMA disc Playback
To repeat one disc:
Press the / button twice.
Random play
The tracks on the disc(s) can be played in random order automatically.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
To repeat all tracks on up to 5 discs:
Press the / button three times.
To repeat desired tracks (CD only):
Perform steps 1 - 6 in "Programmed play" section on page 21 and
then press the / button twice.
To cancel repeat play:
Press the / button again until " " will disappear.
To cancel random play:
Press the / button.
"R" will disappear.
Notes:
If you press the
button during random play, you can move to
the track selected next by the random operation. On the other
hand, the
button does not allow you to move to the previous
track. The beginning of the track being played will be located.
In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the
) button. Otherwise, the disc(s) will play continuously.
20
03/12/17
XL-UH242 20-28.fm
(CD
Advanced CD playback
While in the stop mode, press the
MEMORY button on the remote
control to enter the programming
save mode.
To clear the programmed selections:
Press the CLEAR/DIMMER button on the
remote control while the "MEMORY" indicator
is flashing.
Each time the button is pressed, one track will
be cleared, beginning with the last track
programmed.
Press one of the 1 - 5 buttons
to select the desired disc.
To cancel the programmed play mode:
While in the stop mode and the "MEMORY" indicator is lit, press the
CLEAR/DIMMER button on the remote control. The "MEMORY"
indicator will disappear and all the programmed contents will be
cleared.
You can choose up to 32 selections for playback in the order you like.
1
2
Selected disc number
3
Press the direct search buttons
on the remote control to select
the desired track.
Selected track number
You can also select a track by pressing the
or
button.
4
Press the MEMORY button to
save the track number.
5
Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be
programmed.
If you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR/DIMMER button.
6
Press the (CD ) button.
The total number in memory will
appear.
7
Press the
/
Adding tracks to the program:
If a program has been previously stored, the "MEMORY" indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
To check which tracks are programmed:
While the unit is stopped in the programmed play mode, press the
or
button.
Notes:
When a disc with programmed tracks is ejected, the program is
automatically canceled.
Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed
selections will not be cleared.
During the program operation, random play is not possible.
CD or MP3/WMA disc Playback
Programmed play
XL-UH242
button to start playback.
21
03/12/17
XL-UH242 20-28.fm
CD or MP3/WMA disc Playback
XL-UH242
MP3/WMA folder mode (only for MP3/WMA files)
To playback MP3/WMA (Windows Media Audio) file
There are many music sites on the internet that you can download
MP3/WMA (Windows Media Audio) music files. Follow the
instructions from the website on how to download the music files.
You can then playback these downloaded music files by burning
them to a CD-R/RW disc or by connecting a USB Memory Player
device.
Your downloaded song/files are for personal use only. Any other
usage of the song without owner’s permission, is against the law.
About folder playback order
If MP3/WMA files are recorded in several folders, a folder number will
be set to each folder automatically.
These folders can be selected by the FOLDER button on the remote
control. If there is no supported file formats inside the selected folder,
the folder is skipped and the next folder will be selected.
Example: How to set folder number if MP3/WMA format files are
recorded as below figure.
1. ROOT folder is set as folder 1.
2. As for folders inside ROOT folder (Folder A and Folder B), the
folder which is recorded earlier on the disc will be set as folder 2.
3. As for folder inside Folder A (Folder C and Folder D), the folder
which is recorded earlier on the disc will be set as folder 3.
4. Because there is no folder in Folder C, Folder D will be set as
folder 4.
5. Folder E that is inside Folder D will be set as folder 5.
6. Folder B inside ROOT folder will be set as folder 6.
Folder mode on/off can be operated by the FOLDER button on the
remote control. Files that are played when folder mode is set to the
on position, may differ from those played back when folder mode is
turned off.
Folder Mode Off case:
All the files starting from the selected folder or file will be played back.
If file 3 inside Folder C is selected, all the files starting from file 3 will
be played back.
Folder Mode On case:
All the files inside the selected folder will be played back.
In case Folder D is selected, file 4, 5 and 6 will be played back. File
7 and 8 in Folder E will not be played back.
ROOT
(FOLDER 1)
FOLDER A
(FOLDER 2)
* The folder and file order information which is recorded on the disc
depends on the writing software. There maybe possibilities that this
unit will playback the files not according to our expected playback
order.
FOLDER B
(FOLDER 6)
FOLDER C
(FOLDER 3)
FILE 1
FILE 2
FILE 3
FOLDER D
(FOLDER 4)
FILE 4
FILE 5
FILE 6
FOLDER E
(FOLDER 5)
FILE 9
FILE 10
22
03/12/17
XL-UH242 20-28.fm
FILE 7
FILE 8
XL-UH242
Procedure to playback MP3/WMA disc
To playback CD-R/RW.
Select desired file to be played back by pressing the
or
button. (Folder mode off)
5
Press the
/ (CD
/ ) button.
Playback will start and file name will be displayed.
Press the CD button, and load a MP3/WMA disc.
After disc is loaded, disc info will be displayed.
MP3 indicator
WMA indicator
Disc Name
TOTAL indicator
Disc 1 Blinking
Total number of files
Title, Artist & Album name is displayed if it is recorded on the disc.
Display content can be changed by pressing the DISPLAY button.
File Name Display
TITLE-1 Indicator
Title Display
Function Display
TITLE-2 Indicator
Artist Display
TITLE-3 Indicator
Album Display
In case folder is selected, proceed to step 2.
In case file is selected, proceed to step 4.
2
Press the FOLDER button, and press the TUNING ( or )
button to select desired playback folder. (Folder mode on)
(
1)
FOLDER indicator
(
FOLDER number
Total files in Folder 3
To start playback with folder mode on, go to step 5.
To change the playback folder, press the TUNING (
lect another folder.
3
or
Select desired file to be played back by pressing the
or
button. Proceed to step 5.
) to se-
2)
Clock Display
(
1)
In case of playback with the folder mode on, press the TUNING (
or ) button, and the folder can be selected even though it is in
playback/pause mode.
It will continue playback/pause mode in the 1st track of the selected
folder.
( 1) MP3 ID3-Tag only support version 1.x.
( 2) Only appears when clock is already set.
CD or MP3/WMA disc Playback
1
4
Note:
If "NO SUPPORT" is displayed, it means "Copyright protected
WMA file" or "Not supported playback file" is selected.
23
03/12/17
XL-UH242 20-28.fm
XL-UH242
Listening to USB mass storage device / MP3 Player
1
Press the VIDEO/AUX/USB (USB/AUX) button, and push up
the USB door. Connect the USB Memory device that has
MP3/WMA format files on the unit.
USB Memory Playback
VIDEO
/AUX
USB
When the USB memory is connected to the main unit, the
device information will be displayed.
MP3 indicator
WMA indicator
Volume ID
TOTAL indicator
Total number of files
In case folder is selected, proceed to step 2.
In case file is selected, proceed to step 4.
2
Press the FOLDER button, and press the TUNING ( or )
button to select desired playback folder. (Folder mode on)
FOLDER indicator
Note:
This product is not compatible with MTP and AAC file systems.
FOLDER number
Total files in Folder 2
To start playback with folder mode on, go to step 5.
To change the playback folder, press the TUNING (
button to select another folder.
24
03/12/17
XL-UH242 20-28.fm
or
)
3
Select desired file to be played back by pressing the
or
button. Proceed to step 5.
4
Select desired file to be played back by pressing the
or
button. (Folder mode off)
5
1
Press the USB
button on remote control. Wait until
"UNPLUG OK" appears on FL display.
2
Disconnect USB memory device from the USB terminal.
Press the / (USB / ) button.
Playback will start and the file name will be displayed.
Title, Artist & Album name are displayed if they are recorded in
the USB memory device.
Display content can be changed by pressing the DISPLAY button.
File Name Display
TITLE-1 Indicator
Title Display
Function Display
TITLE-2 Indicator
Artist Display
(
1)
Notes:
SHARP will not be held liable for the loss of data while the USB
memory device is connected to the audio system.
Files compressed in MP3 and / or WMA format can be played
when connected to the USB terminal.
(
2)
Clock Display
(
TITLE-3 Indicator
1)
Album Display
This USB memory’s format supports FAT16 or FAT32.
XL-UH242
USB Memory Playback
To remove USB memory device
SHARP cannot guarantee that all USB memory devices will work
on this audio system.
(
(
1) MP3 ID3-Tag only supports version 1.x.
2) Only appears when clock is already set.
Note:
To pause playback:
Press the CD/USB button.
Auto power off function:
In the stop mode of USB operation, the main unit enters the stand-by
mode after 15 minutes of inactivity.
This USB memory cannot be operated via USB hub.
If "NO SUPPORT" is displayed, it means "Copyright protected
WMA file" or "Not supported playback file" is selected.
In case the data inside the USB memory is large, it may take
longer time for data to be read.
The USB terminal in this unit is not intended for a PC connection
but is used for music streaming with a USB memory device.
25
03/12/17
XL-UH242 20-28.fm
XL-UH242
Advanced USB playback
Repeat play
Repeat play can play all tracks sequence continuously.
To repeat all tracks:
Press the / button twice.
Note:
( ) When folder mode is on, the selected playmode can be used for
the files in the selected folder only.
Notes:
This unit only supports "MPEG-1 Audio Layer-3" format.
(Sampling Frequency fs is 32, 44.1, 48kHz)
"MPEG-2 Audio Layer-3" , "MPEG-2.5 Audio Layer-3" and MP1,
MP2 format are not supported.
USB Memory Playback
Program playback for USB memory is not available.
To cancel repeat play:
Press the / button again until " " disappear.
Random play
The tracks can be played in random order automatically.
To random play all tracks:
Press the RANDOM button on the remote control.
Playback order for MP3 files may differ sometimes depending on
the writing software used during file download.
Bitrate which is supported by MP3 is 32~320 kbps, WMA is
64~160 kbps.
For MP3/WMA files, please put ".MP3" ".WMA" extension. Files
cannot be played back if there is no MP3/WMA extension.
Playlists are not supported by this unit.
This unit can display Folder Name or File Name up to 32
characters.
This unit only supports MP3 ID3-Tag version 1.x.
The display playback time may not be displayed correctly when
playing back a variable bitrate file.
To cancel random play:
Press the / button.
"R" will disappear.
Notes:
If you press the
button during random play, you can move to
the track selected next by the random operation. On the other
hand, the
button does not allow you to move to the previous
track. The beginning of the track being played will be located.
In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
Caution:
After performing repeat, be sure to press the (USB ) button.
Otherwise, it will play continuously.
Time display cannot be changed by the DISPLAY button.
Title name and artist name can be displayed by pressing the
DISPLAY button during file playback or pause mode.
WMA meta tag also supports title, artist and album name which
are recorded in WMA files.
Copyright protected WMA files cannot be played back.
26
03/12/17
XL-UH242 20-28.fm
Listening to the radio
XL-UH242
Tuning
Press the ON/STAND-BY button to turn the power on.
3
Press the TUNING ( or ) button on the remote control to
tune in to the desired station.
ON/STANDBY
TUNER
(BAND)
Press the TUNER (BAND) button repeatedly to select the
desired frequency band (FM or AM).
Manual tuning:
Press the TUNING ( or ) button as many times as required
to tune in to the desired station.
Auto tuning:
When the TUNING ( or ) button is pressed for more than 0.5
seconds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may stop automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING ( or ) button
again.
Radio
POWER
1
2
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.
" " will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button to
extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer.
FM stereo mode indicator
Auto power on function:
When you press any of the following buttons, the unit turns on.
TUNER (BAND) button (main unit and remote control): The unit
turns on and the "TUNER" function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TUNER,VIDEO/AUX/USB).
FM stereo receiving indicator
03/12/17
XL-UH242 20-28.fm
27
XL-UH242
Listening to the radio (continued)
Memorizing a station
Radio
You can store 40 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
1
2
Perform steps 1 - 3 in "Tuning" on page 27.
3
Within 30 seconds, press the PRESET ( or ) button to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
4
Within 30 seconds, press the MEMORY button to store that
station in memory.
Press the MEMORY button to enter the preset tuning
saving mode.
If the "MEMORY" and preset number indicators disappear
before the station is memorized, repeat the operation from step
2.
5
Repeat steps 1 - 4 to set other stations, or to change a preset station.
When a new station is stored in memory, the station previously
memorized for that preset channel number will be erased.
To recall a memorized station
Press the PRESET ( or
lect the desired station.
) button for less than 0.5 seconds to se-
To scan the preset stations
The stations saved in memory can be scanned automatically. (Preset memory scan)
1 Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
2 Press the PRESET ( or ) button again when the desired station is located.
To erase entire preset memory
1
2
Press the ON/STAND-BY button to enter the stand-by mode.
While pressing down the 1 button and the
5 button, press
the TUNER (BAND) button until "TUNER CLEAR" appears.
Note:
The backup function protects the memorized stations for a few
hours should there be a power failure or the AC power cord
become disconnected.
28
03/12/17
XL-UH242 20-28.fm
Timer and sleep operation (Remote Control only)
XL-UH242
Timer playback:
The unit turns on and plays the desired source (CD, TUNER, USB,
AUX) at a preset time.
Once timer:
Once timer play works for one time only at a preset
time.
Daily timer:
Daily timer play works at the same preset time
every day.
For example, set the timer as a wake-up call every morning.
Timer playback
Using the once timer and daily timer in combination:
For example, use the once timer to listen to a radio program, and
use the daily timer to wake up.
1 Set the daily timer (pages 29 - 31).
2 Set the once timer (pages 29 - 31).
1 minute or more
Once timer
Daily timer
Start
Stop
Start
Stop
Note:
When set times for the daily timer and once timer overlap, the once
timer takes priority. Allow an interval of at least 1 minute between
operations.
Before setting timer:
1 Check that the clock is set to the correct time (refer to page 15).
If it is not set, you cannot use the timer function.
2 For timer playback: Load discs to be played.
1
2
3
Press the ON/STAND-BY button to turn the power on.
Advanced Features
This unit has 2 types of timer: ONCE TIMER and DAILY TIMER.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to
select "ONCE" or "DAILY", and press the MEMORY button.
Set the clock to the correct time if "ONCE" or "DAILY" does not
appear.
Continued to the next page
29
XL-UH242 29-37.fm
XL-UH242
Timer and sleep operation (Remote Control only) (continued)
4
Within 10 seconds, press the
or
button to
select "ONCE SET" or "DAILY SET", and press the
MEMORY button.
8
Switch input with the
or
press the MEMORY button.
button, and then
To select the timer playback source: CD, TUNER, USB or
AUX.
When you select the tuner, select a station by pressing the
or
button, and then press the MEMORY
button.
Advanced Features
5
Press the
or
button to adjust the hour and
then press the MEMORY button.
If a station has not been programmed, "NO PRESET" will
be displayed and timer setting will be canceled.
9
Adjust the volume using the VOLUME control, and then
press the MEMORY button.
Do not turn the volume up too high.
The illustrations show the timer playback setting in the daily
timer mode.
6
Press the
or
button to adjust the minutes and
then press the MEMORY button.
7
Set the time to finish as in steps 5 and 6 above.
10
Press the ON/STAND-BY button to enter the power standby mode.
The "TIMER" indicator lights up and the unit is ready for timer
playback.
Continued to the next page
30
XL-UH242 29-37.fm
XL-UH242
When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the preset
volume.
12
When the timer end time is reached, the system will enter
the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer will operate at the same time every day. It will
continue until the daily timer setting is canceled. Cancel the
daily timer when it is not in use.
Note:
When performing timer playback using another unit connected to the
USB terminal or AUX IN jacks, select "USB" or "AUX" in step 8.
This unit will turn on or enter the power stand-by mode automatically,
however, the connected unit to AUX IN jacks will not turn on or off.
Checking the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE CALL" or "DAILY CALL", and press the MEMORY button.
The unit returns to the timer stand-by mode after displaying the
settings in order.
Canceling the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE OFF" or "DAILY OFF", and press the MEMORY button.
Timer will be canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse the
same setting, perform the following operations.
1 Turn the power on and press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE ON" or "DAILY ON", and press the MEMORY button.
4 Press the ON/STAND-BY button to enter the power stand-by
mode.
Advanced Features
11
31
XL-UH242 29-37.fm
XL-UH242
Timer and sleep operation (Remote Control only) (continued)
Sleep operation
Advanced Features
The radio, compact disc and USB can be turned off automatically.
1
2
3
Play back the desired sound source.
4
Press the
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
"SLEEP", and press the
MEMORY button.
or
button to select the time.
(Maximum: 3 hours - Minimum: 1 minute)
3 hours - 5 minutes 5-minute intervals
5 minutes - 1 minute 1-minute intervals
5
Press the MEMORY button.
"SLEEP" will appear.
6
To cancel the sleep operation:
Press the ON/STAND-BY button while "SLEEP" is indicated.
To cancel the sleep operation without setting the unit to the stand-by
mode, proceed as follows.
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP OFF", and press the MEMORY button.
To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up
to CD in the next morning.
1
2
Set the sleep time (see left, steps 1 - 5).
While the sleep timer is set, set the timer playback
(steps 2 - 10, pages 29 - 30).
Sleep timer setting
The unit will enter the power stand-by mode automatically
after the preset time has elapsed.
The volume will be turned down 1 minute before the sleep
operation finishes.
To confirm the remaining sleep time:
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP X : XX".
"X : XX" is sleep remaining time.
The remaining sleep time is displayed for about 10 seconds.
You can change the remaining sleep time while it is displayed by
pressing the MEMORY button (steps 4 - 5).
Timer playback setting
1 minute - 3 hours
Sleep operation will
automatically stop.
End time
Desired time
Timer playback start time
32
XL-UH242 29-37.fm
Enhancing your system
XL-UH242
Listening to the playback sounds from VCR,
DVD, etc.
The connection cord is not included. Purchase a commercially
available cord as shown below.
1
Use a connection cord to connect the VCR, DVD, etc. to the
VIDEO/AUX IN jacks.
VIDEO/AUX IN
When using video equipment, connect the audio output to this
unit and the video output to a television.
LEFT
ANTENNA
FM
75 OHMS
GND AM
VIDEO/AUX IN
RIGHT
LEFT
2
3
4
Press the ON/STAND-BY button to turn the power on.
Press the VIDEO/AUX/USB button.
Play the connected equipment.
SPEAKERS
SUBWOOFER
PRE-OUT
SPEAKERS
LIGHT-UP
LEFT RIGHT
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
AC INPUT
RIGHT
LEFT
Note:
To prevent noise interference, place the unit away from the
television.
Headphones
CD
TUNER
(BAND)
Before plugging in or unplugging the headphones, reduce the
volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter plug and
impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
Advanced Features
RIGHT
Auto power on function:
When you press any of the following buttons, the unit turns on.
VIDEO/AUX/USB button (main unit and remote control): The unit
turns on and the "USB" or "AUX" function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TUNER,VIDEO/AUX/USB).
33
XL-UH242 29-37.fm
XL-UH242
Enhancing your system (continued)
Subwoofer connection
Many potential problems can be resolved by the owner without calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
General
Symptom
The clock is not set to the
correct time.
When a button is pressed,
the unit does not respond.
ANTENNA
FM
75 OHMS
GND AM
VIDEO/AUX IN
RIGHT
LEFT
No sound is heard.
RIGHT
LEFT
SUBWOOFER
PRE-OUT
AC INPUT
SPEAKERS
LIGHT-UP
LEFT RIGHT
SPEAKERS
RATED SPEAKER IMPEDANCE:
6 OHMS MIN.
Possible cause
Did a power failure occur? Reset
the clock.
Set the unit to the power standby mode and then turn it back on.
If the unit still malfunctions, reset
it.
Is the volume level set to "0"?
Are the headphones connected?
Are the speaker wires
disconnected?
CD player
SUBWOOFER
PRE-OUT
Advanced Features
When a commercially available subwoofer with a built-in amplifier is
connected to this unit, you can enjoy sound with emphasized bass.
Connect an RCA cord from a commercially available speaker with a
built-in amplifier to the SUBWOOFER PRE-OUT jack.
Troubleshooting chart
Subwoofer with a
built-in amplifier
Symptom
Playback does not start.
Playback stops in the
middle or is not performed
properly.
Playback sounds are
skipped, or stopped in the
middle of a track.
Possible cause
Is the disc loaded upside down?
Does the disc satisfy the
standards?
Is the disc distorted or
scratched?
Is the unit located near excessive
vibrations?
Is the disc very dirty?
Has condensation formed inside
the unit?
34
XL-UH242 29-37.fm
XL-UH242
Remote control
Symptom
The remote control does
not operate.
If trouble occurs
Possible cause
Is the AC power cord of the unit
plugged in?
Is the battery polarity correct?
Are the batteries dead?
Is the distance or angle
incorrect?
Does the remote control sensor
receive strong light?
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
Tuner
Symptom
The radio makes unusual
noises continuously.
Possible cause
Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop
antenna placed properly? Move
the antenna away from the AC
power cord if it's located nearby.
Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc in the unit until normal playback is
possible (about 1 hour). Wipe off any condensation on the transmitter
with a soft cloth before operating the unit.
2
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the
1 button and the 5 button, press
the POWER ON/STANDBY button until "CLEAR ALL" appears.
POWER
ON/STANDBY
References
Clearing all the memory (reset)
1
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD program.
35
XL-UH242 29-37.fm
XL-UH242
Troubleshooting chart (continued)
Cleaning the CD pickup lens
Before transporting the unit
Remove all CDs from the unit. Make sure there is no CD in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the
unit with discs left inside can damage the unit.
References
Care of compact discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD
collection and player.
Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
Keep your discs away from direct sunlight, heat, and excessive
moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
NO
Maintenance
In order to ensure proper operation of the CD player, preventative
maintenance (cleaning of the laser pickup lens) should be
performed periodically. Lens cleaners are commercially available.
Contact your local CD software dealer for options.
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Caution:
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of the unit. It may cause
malfunctions.
YES
Correct
36
XL-UH242 29-37.fm
Specifications
General
Power source
Power
consumption
Dimensions
Weight
AC 120 V, 60 Hz
90 W
Width: 6-3/4" (175 mm)
Height: 9-1/2" (240 mm)
Depth: 12-1/5" (315 mm)
12.4 lbs. (5.6 kg)
CD player
Type
Signal readout
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser
pickup
1-bit D/A converter
20 - 20,000 Hz
D/A converter
Frequency
response
Dynamic range
90 dB (1 kHz)
Tuner
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1,720 kHz
Amplifier
Output power
Output terminals
Input terminals
90 watts minimum RMS per channel into 6
ohms from 100 Hz to 20 kHz, 10% total harmonic distortion
Speakers: 6 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Subwoofer pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
Video/Auxiliary (audio signal):
500 mV/47 k ohms
USB
Class
Support File
Format support
Bitrate support
Other
Mass storage class
MP3/WMA (do not support DRM file)
FAT 16 or FAT 32
MP3 (32 ~ 320 kbps)
WMA (64 ~ 160 kbps)
MP3 lD3 - tag only supports version 1.x
USB supports version 2.0
Speaker
Type
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
2-way type speaker system
2" (5 cm) tweeter
5-1/8" (13 cm) woofer
180 W
References
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be
some deviations from these values in individual units.
XL-UH242
90 W
6 ohms
Width: 7-1/4" (185 mm)
Height: 10-1/4" (260 mm)
Depth: 9-1/16" (230 mm)
6.1 lbs. (2.8 kg/each)
37
XL-UH242 29-37.fm
MEMO
MEMO
1
11/16/05, 4:41 PM
MEMO
MEMO
2
11/16/05, 4:41 PM
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
CONSUMER
WARRANTY
This warranty does LIMITED
not apply to any
appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
SHARP
ELECTRONICS
CORPORATION
warrants
to the
consumer
purchaser
this Sharp
brand
product
(the “Product”),
when
in its or
original
con-in
been damaged
or defaced,
which has been
subjected
to first
improper
voltage
or other that
misuse,
abnormal
service
or handling,
or which
hasshipped
been altered
modified
tainer,
will
free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
design
orbe
construction.
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
The damaged
limited warranty
described
is in addition
to to
whatever
implied
warranties
may be granted
purchasers
by law. ALL
IMPLIED
WARRANTIES
been
or defaced,
whichherein
has been
subjected
improper
voltage
or other misuse,
abnormaltoservice
or handling,
or which
has been
altered or INCLUDING
modified in
THE WARRANTIES
design
or construction.OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
The
limited warranty
described
herein
is in addition
whatever
implied
warranties
beyond the
time period
described
hereintoon
behalf of
Sharp.warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
The
warranties
described
herein
shall
be
the
sole
and
exclusive
warranties
granted
by Sharp
and may
shall not
be the
sole
Some states do not allow limitations on how long an implied warranty lasts, so
the above
limitation
apply
to and
you.exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
Neither
the sales
personnel
of the
seller and
nor any
personfull
is satisfaction
authorized to
any warranties
otheron
than
those described
herein,
to extend
the duration
ofevent
any
purchaser
with respect
to the
Product,
shallother
constitute
of make
all claims,
whether based
contract,
negligence,
strict or
liability
or otherwise.
In no
warranties
beyond
the or
time
described
herein
behalf
of Sharp.
shall Sharp
be liable,
in period
any way
responsible,
foron
any
damages
or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other
than an authorized
servicer.
Norbe
shall
be exclusive
liable or inwarranties
any way responsible
anyand
incidental
or the
consequential
economic
or property
damage.
states
The
warranties
described herein
shall
the Sharp
sole and
granted by for
Sharp
shall be
sole and exclusive
remedy
available
to theSome
purchaser.
do not allow
the exclusion
incidental
or consequential
damages,
so the
above
exclusion
may
not apply
to you. of all liabilities and responsibilities of Sharp to the
Correction
of defects,
in the of
manner
and for
the period of time
described
herein,
shall
constitute
complete
fulfillment
purchaser
with respect
to theYOU
Product,
and shall
constitute
full satisfaction
of all claims,
whether RIGHTS
based onWHICH
contract,
negligence,
strict liability
or otherwise. In no event
THIS WARRANTY
GIVES
SPECIFIC
LEGAL
RIGHTS.
YOU MAY ALSO
HAVE OTHER
VARY
FROM STATE
TO STATE.
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
Model
Specific
Section
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
XL-UH242 Micro Component System
Product
Model Number
& Description:
doYour
not allow
the exclusion
of incidental
or consequential damages, so the above exclusion may not apply to you.
(Be sure to have this information available when you need service for your Product.)
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Model
Specific
Section
Additional
Item(s)
Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Your Product Model Number & Description:
Where to Obtain Service:
At a
Sharp
Authorized
Servicer located
in when
the United
States.
(Be
sure
to have
this information
available
you need
service for your Product.)
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional
accessories,
supplies, and
consumable
items.
Be sure to have
Proof of Purchase
available.
If you ship
the Product, be sure it is insured and
Where to Obtain Service:
Atpackaged
a Sharp Authorized
securely. Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship
prepaid
or carry in
your Product to a Sharp
Servicer.
TO OBTAIN SUPPLY, ACCESSORY
OR
PRODUCT
INFORMATION,
CALLAuthorized
1-800-BE-SHARP.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
0311
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
0311
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
03/12/17
XL-UH242_BACK.fm
Printed in Malaysia
TINSEA122AWZZ
06C R AS 1