Epson D6150 Projector User manual
Add to my manualsadvertisement
PowerLite
®
D6150/D6155W/D6250
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Connect the projector
Choose from the following connections:
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
Connect one end of the cable to the projector’s Computer1 or Computer2 port, and the other end to your computer’s monitor port. If you are using a notebook, switch it to external display (see “Troubleshooting”). You can also connect an audio cable. See the User's Guide on your projector CD for details.
Camera, USB Device, or Epson Document Camera DC-06
Connect a digital camera, USB flash drive, USB storage device, or Epson document camera DC-06 to the projector’s USB TypeA (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can use the projector’s Slideshow feature. See the User’s Guide on your projector
CD for details.
External Monitor and External Speakers
You can also connect an external monitor and external speakers to your projector to enhance your presentations. See the User’s Guide on your projector
CD for details.
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector.
Wired Network
You can connect the projector to your network using an Ethernet ® cable.
See “Project over a wired network” for instructions.
Wireless Network
You can connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n wireless network using the optional Epson wireless LAN module. See “Project
Video Device
Connect up to 5 video devices and use the Source Search button on the projector or remote control to switch between them. (All cables are optional).
See the User's Guide on your projector CD for details.
RCA video cable (composite video)
S-Video cable
Audio cable
Component video to VGA cable
Audio cable
HDMI cable
The power light on the projector turns orange.
3
Press the power button on the projector or remote control.
Power light
Power button
The power light flashes green, then stays on.
Note: To shut down the projector, press the power button twice, then unplug it. You don’t have to wait for the projector to cool down.
4
The default language of the menu system is English. To select another language, press the Menu button on the remote control. Select
Extended and press Enter. Select Language and press Enter. Select your language and press Enter. Press the Menu button to exit the menu system.
Adjust the image
1
If you don’t see an image, press the Source Search button on the projector or the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position.
3
Open the zoom/focus ring cover and rotate the focus ring to sharpen the image.
Zoom/focus ring cover
Focus ring
4
Turn the zoom ring to reduce or enlarge the image.
Zoom ring
5
If your image looks like or , you’ve placed the projector off to one side of the screen at an angle. Place it directly in front of the center of the screen, facing the screen squarely. Or press the or buttons on the projector to correct it.
6
If your image looks like or , press the or buttons on the projector to correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Turn projector on and off
Turn off projector display and sound
Choose which source to display
Access projector menus
Control projector volume
Navigate projector menus
Project over a wired network
Follow the steps here to configure your projector for your wired network using the projector’s menu system.
1
Plug in and turn on the projector.
2
Press the Menu button on the remote control, select the Network menu, and press Enter.
3
Select Network Configuration and press Enter.
4
Select the Basic menu and press Enter.
5
Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press Enter to select them.
Note: See the User’s Guide on the projector CD for information on adding passwords.
6
Select the Wired LAN menu and press Enter.
7
Choose IP Settings and press Enter.
8
If your network assigns addresses automatically, select IP Settings and turn on the DHCP setting. If not, turn off the DHCP setting and enter the projector’s IP Address, Subnet Mask, and Gateway Address, as needed.
9
To prevent the IP address from appearing on the network standby screen, set the IP Address Display setting to Off.
For more information on using the remote control, see the User’s Guide on your projector CD.
*412046400*
*412046400*
PowerLite
®
D6150/D6155W/D6250
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Connect the projector
Choose from the following connections:
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
Connect one end of the cable to the projector’s Computer1 or Computer2 port, and the other end to your computer’s monitor port. If you are using a notebook, switch it to external display (see “Troubleshooting”). You can also connect an audio cable. See the User's Guide on your projector CD for details.
Camera, USB Device, or Epson Document Camera DC-06
Connect a digital camera, USB flash drive, USB storage device, or Epson document camera DC-06 to the projector’s USB TypeA (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can use the projector’s Slideshow feature. See the User’s Guide on your projector
CD for details.
External Monitor and External Speakers
You can also connect an external monitor and external speakers to your projector to enhance your presentations. See the User’s Guide on your projector
CD for details.
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector.
Wired Network
You can connect the projector to your network using an Ethernet ® cable.
See “Project over a wired network” for instructions.
Wireless Network
You can connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n wireless network using the optional Epson wireless LAN module. See “Project
Video Device
Connect up to 5 video devices and use the Source Search button on the projector or remote control to switch between them. (All cables are optional).
See the User's Guide on your projector CD for details.
RCA video cable (composite video)
S-Video cable
Audio cable
Component video to VGA cable
Audio cable
HDMI cable
The power light on the projector turns orange.
3
Press the power button on the projector or remote control.
Power light
Power button
The power light flashes green, then stays on.
Note: To shut down the projector, press the power button twice, then unplug it. You don’t have to wait for the projector to cool down.
4
The default language of the menu system is English. To select another language, press the Menu button on the remote control. Select
Extended and press Enter. Select Language and press Enter. Select your language and press Enter. Press the Menu button to exit the menu system.
Adjust the image
1
If you don’t see an image, press the Source Search button on the projector or the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position.
3
Open the zoom/focus ring cover and rotate the focus ring to sharpen the image.
Zoom/focus ring cover
Focus ring
4
Turn the zoom ring to reduce or enlarge the image.
Zoom ring
5
If your image looks like or , you’ve placed the projector off to one side of the screen at an angle. Place it directly in front of the center of the screen, facing the screen squarely. Or press the or buttons on the projector to correct it.
6
If your image looks like or , press the or buttons on the projector to correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Turn projector on and off
Turn off projector display and sound
Choose which source to display
Access projector menus
Control projector volume
Navigate projector menus
Project over a wired network
Follow the steps here to configure your projector for your wired network using the projector’s menu system.
1
Plug in and turn on the projector.
2
Press the Menu button on the remote control, select the Network menu, and press Enter.
3
Select Network Configuration and press Enter.
4
Select the Basic menu and press Enter.
5
Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press Enter to select them.
Note: See the User’s Guide on the projector CD for information on adding passwords.
6
Select the Wired LAN menu and press Enter.
7
Choose IP Settings and press Enter.
8
If your network assigns addresses automatically, select IP Settings and turn on the DHCP setting. If not, turn off the DHCP setting and enter the projector’s IP Address, Subnet Mask, and Gateway Address, as needed.
9
To prevent the IP address from appearing on the network standby screen, set the IP Address Display setting to Off.
For more information on using the remote control, see the User’s Guide on your projector CD.
*412046400*
*412046400*
10
When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
11
Press the Menu button to exit the menu system.
12
See “Install network software” for additional instructions
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11b,
802.11g, or 802.11n wireless network. You must install the optional Epson wireless LAN module (part number V12H418P12). Your computer must have a wireless card or built-in wireless interface, and be running Windows ® 7,
Windows Vista ® , Windows XP Professional x64, Windows XP, or Windows 2000, or Mac OS ® X 10.3 to 10.6.
1
Turn off the projector and unplug the power cord.
2
Remove the screw securing the wireless LAN module stopper, then remove the stopper.
3
Insert the wireless LAN module into the port.
8
Choose Network Configuration and press Enter.
9
Select the Basic menu and press Enter.
10
Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press Enter to select them.
Note: See the User’s Guide on the projector CD for information on adding passwords.
11
Select the Wireless LAN menu and press Enter.
4
Replace the wireless LAN module stopper as shown below and secure it using the screw you removed.
5
Plug in and turn on the projector.
6
To configure your projector for your wireless network, do one of the following:
• If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait for the displayed message, remove the key, and connect it to a USB port on your computer. Follow the on-screen instructions to install the driver, then run your presentation. For details, see the User’s
Guide on your projector CD.
• If you’re not using the key, continue with these steps.
7
Press the Menu button on the remote control, select the Network menu, and press Enter.
12
Select the Connection Mode setting and choose one of these options:
• Quick to connect the projector to one computer on the network
• Advanced to connect the projector to multiple computers on the network
13
If you selected Quick connection mode, select the Channel setting for your wireless network and turn on the SSID Auto Setting setting.
14
Select the type of wireless network you are using as the Wireless LAN
Sys. setting.
15
If you selected Advanced connection mode, enter your network SSID (up to 32 characters) as the SSID setting.
16
If your network assigns addresses automatically, select IP Settings and turn on the DHCP setting. If not, turn off the DHCP setting and enter the projector’s IP Address, Subnet Mask, and Gateway Address, as needed.
17
To prevent the SSID and IP address from appearing on the network standby screen, set the SSID Display and/or IP Address Display settings to Off.
18
When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
.
19
Press the Menu button to exit the menu system.
20
See “Install network software” for additional instructions.
Install network software
Install the EasyMP ® Network Projection software on each computer that will project over the network. Use the CD labeled Epson Projector Software to install the program.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is installed along with your projector User’s Guide.
To monitor and control your projector over the network, download and install the EasyMP Monitor software and manual from the Epson support web site.
You can install links to the download pages from your projector CD, or go to
www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and select your projector.
Troubleshooting
If you see a blank screen or the No signal message after turning on your computer or video device, check the following:
• Make sure the power light on the projector is green and not flashing.
• Press the Source Search button on the projector or the remote control to select the computer as the image source.
• If you’re using a Windows notebook, press the function key on your keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as . You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear.
• On a Macintosh ® , select the Mirror Displays setting in the System
Preferences Displays utility.
Where to get help
Manuals
For more information about using the projector, install the manuals from your projector CD. View the guides by clicking the icons for them on your computer desktop.
Telephone Support Services
To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the
PIN on the Epson PrivateLine Support card included with your projector. This service is available 6 am
to 6 pm
, Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing:
US: (562) 276-4394, 6 am
to 8 pm
, Pacific Time, Monday through Friday, and 7 am to 4 pm
, Pacific Time, Saturday
Canada: (905) 709-3839, 6 am
to 8 pm
, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Internet Support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the User’s Guide on your projector CD.
You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).
Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Epson and EasyMP are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko
Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2011 Epson America, Inc. 1/11
Printed in XXXXXX CPD-33690
10
When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
11
Press the Menu button to exit the menu system.
12
See “Install network software” for additional instructions
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11b,
802.11g, or 802.11n wireless network. You must install the optional Epson wireless LAN module (part number V12H418P12). Your computer must have a wireless card or built-in wireless interface, and be running Windows ® 7,
Windows Vista ® , Windows XP Professional x64, Windows XP, or Windows 2000, or Mac OS ® X 10.3 to 10.6.
1
Turn off the projector and unplug the power cord.
2
Remove the screw securing the wireless LAN module stopper, then remove the stopper.
3
Insert the wireless LAN module into the port.
8
Choose Network Configuration and press Enter.
9
Select the Basic menu and press Enter.
10
Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press Enter to select them.
Note: See the User’s Guide on the projector CD for information on adding passwords.
11
Select the Wireless LAN menu and press Enter.
4
Replace the wireless LAN module stopper as shown below and secure it using the screw you removed.
5
Plug in and turn on the projector.
6
To configure your projector for your wireless network, do one of the following:
• If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait for the displayed message, remove the key, and connect it to a USB port on your computer. Follow the on-screen instructions to install the driver, then run your presentation. For details, see the User’s
Guide on your projector CD.
• If you’re not using the key, continue with these steps.
7
Press the Menu button on the remote control, select the Network menu, and press Enter.
12
Select the Connection Mode setting and choose one of these options:
• Quick to connect the projector to one computer on the network
• Advanced to connect the projector to multiple computers on the network
13
If you selected Quick connection mode, select the Channel setting for your wireless network and turn on the SSID Auto Setting setting.
14
Select the type of wireless network you are using as the Wireless LAN
Sys. setting.
15
If you selected Advanced connection mode, enter your network SSID (up to 32 characters) as the SSID setting.
16
If your network assigns addresses automatically, select IP Settings and turn on the DHCP setting. If not, turn off the DHCP setting and enter the projector’s IP Address, Subnet Mask, and Gateway Address, as needed.
17
To prevent the SSID and IP address from appearing on the network standby screen, set the SSID Display and/or IP Address Display settings to Off.
18
When you are finished, select Complete and press Enter, then press
Enter again to save your settings.
.
19
Press the Menu button to exit the menu system.
20
See “Install network software” for additional instructions.
Install network software
Install the EasyMP ® Network Projection software on each computer that will project over the network. Use the CD labeled Epson Projector Software to install the program.
For instructions on installing and using your network software, see the EasyMP
Network Projection Operation Guide on your projector CD. This guide is installed along with your projector User’s Guide.
To monitor and control your projector over the network, download and install the EasyMP Monitor software and manual from the Epson support web site.
You can install links to the download pages from your projector CD, or go to
www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and select your projector.
Troubleshooting
If you see a blank screen or the No signal message after turning on your computer or video device, check the following:
• Make sure the power light on the projector is green and not flashing.
• Press the Source Search button on the projector or the remote control to select the computer as the image source.
• If you’re using a Windows notebook, press the function key on your keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as . You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear.
• On a Macintosh ® , select the Mirror Displays setting in the System
Preferences Displays utility.
Where to get help
Manuals
For more information about using the projector, install the manuals from your projector CD. View the guides by clicking the icons for them on your computer desktop.
Telephone Support Services
To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the
PIN on the Epson PrivateLine Support card included with your projector. This service is available 6 am
to 6 pm
, Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing:
US: (562) 276-4394, 6 am
to 8 pm
, Pacific Time, Monday through Friday, and 7 am to 4 pm
, Pacific Time, Saturday
Canada: (905) 709-3839, 6 am
to 8 pm
, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Internet Support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the User’s Guide on your projector CD.
You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).
Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Epson and EasyMP are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko
Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2011 Epson America, Inc. 1/11
Printed in XXXXXX CPD-33690
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- White
- LCD 3500 ANSI lumens
- Lamp 4000 h
- XGA (1024x768) 2000:1
- Number of colours: 16.78 million colours
- Focus: Manual Zoom capability
- Ethernet LAN
- Built-in speaker(s) 5 W
- AC 328 W
Related manuals
advertisement
Table of contents
- 1 Quick Setup
- 1 Connect the projector
- 1 Computer Monitor Port
- 1 Wired Network
- 1 Wireless Network
- 1 Video Device
- 1 Camera, USB Device, or Epson Document Camera DC-06
- 1 Turn on your equipment
- 2 Adjust the image
- 2 Using the remote control
- 2 Project over a wirednetwork
- 3 Project wirelessly
- 4 Install network software
- 4 Troubleshooting
- 4 Where to get help
- 4 Optional accessories