Agri-Fab 71-24537 Owner's manual
Add to my manualsadvertisement
Owner's Manual
®
48" SLEEVE HITCH ROCK RAKE
Model No. 486.24537
Before using this product, read this manual and follow all Safety
Rules and
Operating Instructions.
IMPORTANT - READ THIS FIRST!!!
For Missing Parts or Assembly Questions
Please Call 866-576-8388
Mon.-Fri. 7 am - 5 pm CST.
Missing parts will be sent UPS in 24 hours directly to your home.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
PRINTED IN U.S.A.
• Safety
• Assembly
• Operation
• Maintenance
• Parts
FORM NO. 49526 (2/05)
TABLE OF CONTENTS
SAFETY RULES ..........................................................2
FULL SIZE HARDWARE CHART ................................3
CARTON CONTENTS .................................................3
ASSEMBLY ..................................................................4
OPERATION ................................................................5
MAINTENANCE/STORAGE ........................................6
REPAIR PARTS ILLUSTRATION ................................7
REPAIR PARTS LIST ..................................................7
PARTS ORDERING/SERVICE .....................Back Page
WARRANTY
LIMITED ONE YEAR WARRANTY
For one year from the date of purchase, when this product is maintained and lubricated according to the operating and maintenance instructions in the owner's manual, Sears will repair any defect in material or workmanship free of charge. If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.
This warranty does not cover repairs necessary because of operator negligence or abuse, including the failure to maintain the equipment according to instructions contained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT
IN THE UNITED STATES.
This warranty applies only while this product is in the United States.
This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co. D/817 WA. Hoffman Estates, Chicago, IL 60179
The model number and serial numbers will be found on a decal attached to the hitch assembly.
You should record both the serial number and the date of purchase and keep in a safe place for future reference.
MODEL NUMBER: 486.24537
SERIAL NUMBER: __________________
DATE OF PURCHASE: __________________
SAFETY
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.
Exercise caution at all times, when using power equipment.
• Read this owners manual and your vehicle and sleeve hitch owners manuals before using this rake.
• Do not allow children to operate the vehicle or rake.
• Do not allow adults to operate the vehicle or rake without proper instructions.
• Do not allow anyone to ride on the rake.
• Before lowering and operating the rake, be sure no one is near the area of operation.
• Lower the rake when leaving the vehicle unattended.
• Vehicle braking and stability may be affected with the attachment of this rake. Drive slowly with the rake in transport position. Stay off of steep slopes.
• Stop and inspect for damage after striking an object.
Repair any damage before continuing operation.
• Keep all nuts and bolts tight and be sure the equipment is in safe operating condition.
• Always place the sleeve hitch in the lowered position when installing or removing the rake.
Look for this symbol to point out important safety precautions. It means-Attention!! Become alert!! Your safety is involved.
2
A
B
HARDWARE PACKAGE CONTENTS
SHOWN FULL SIZE
C
D E F
B
C
24 Hex Bolt, 3/8" x 1"
24
1
Nylock Hex Nut, 3/8"
Slotted Hex Nut, 1"
2
REF. QTY.
D
E
F
1
DESCRIPTION
Pivot Pin
3
1
CARTON CONTENTS
1. Hitch Assembly
2. Rake Pivot Assembly
3. Rake Tines (24)
3
TOOLS REQUIRED FOR ASSEMBLY
(2) 9/16" Wrenches
(2) 1-1/2" Wrenches or 14" Adjustable Wrenches
ASSEMBLY
• Align the hitch assembly (pointing in direction shown) and the rake assembly. Place the hitch assembly down onto the threaded stud on the rake assembly and install the 1" slotted hex nut onto the threaded stud. Tighten the nut until it is just snug. See fi gure 2.
1" SLOTTED HEX NUT
REMOVAL OF PARTS FROM CARTON
• Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify.
ASSEMBLING THE RAKE
• Attach the 24 rake tines to the rake pivot assembly using a 3/8" x 1" hex bolt and 3/8" nylock hex nut for each tine. Insert the ends of the tines through the slots in the rear of the rake pivot assembly. Make sure all nuts and bolts are securely tightened. See fi gure 1.
3/8” NYLOCK NUT
RAKE PIVOT ASSEMBLY
HITCH ASSEMBLY
FIGURE 2
RAKE ASSEMBLY
• Back the slotted nut off until the fi rst slot in the nut lines up with the hole in the threaded stud. If the hitch assembly will not pivot on the threaded stud, back the nut off to the next slot. Install the cotter pin through the stud and spread the ends of the pin. See fi gure 3.
3/8” x 1” HEX BOLT
RAKE TINE
1" SLOTTED HEX NUT
COTTER PIN
FIGURE 1
STUD
HOLE
4
FIGURE 3
• Lock the rake assembly in the straight ahead position by installing the pivot pin through the hole in the rear of the hitch assembly. Secure the pivot pin using the hair cotter pin. See fi gure 4.
PIVOT PIN
HAIR COTTER PIN
FIGURE 4
OPERATION
ATTACHING AND REMOVING RAKE
CAUTION: Use care when working around a raised rake. Keep hands and feet out from under the rake at all times. Serious injury can result should the rake drop unexpectedly.
CAUTION: Always place the sleeve hitch in the lowered position when installing or removing the rake.
Refer to your sleeve hitch manual and to fi gure 5.
• Attach the rake to the sleeve hitch on your tractor using the sleeve hitch pin.
• Screw the two sleeve hitch stabilizer bolts against the rake hitch and then tighten the jam nuts to eliminate looseness in the hookup.
• Adjust the sleeve hitch so that the rake is free to go below ground level but can still be raised a minimum of 5" above ground for transport.
• Stabilizer bolts and jam nuts should be loosened before removing the rake from the sleeve hitch.
STABILIZER BOLTS
TRACTOR SLEEVE HITCH
FIGURE 5
5
ADJUSTING ANGLE OF RAKE
• The rake can be angled 24 degrees in either direction as shown in fi gure 6. To change the angle: a. Raise the rake so that the tines of the rake are
off the ground.
b. Remove the pivot pin from the hitch assembly.
c. Pivot the rake assembly to the right or the left.
d. Align the hole in the pivot plate with the hole in
the hitch assembly. Install the pivot pin through the
aligned holes and secure with the haircotter pin.
• To reverse the rake, remove the cotter pin and slotted nut from the threaded stud on the rake assembly.
Remove the rake pivot assembly from the hitch assembly, rotate it 180 degrees and then reattach it to the hitch assembly.
HOW TO USE YOUR RAKE
Use this rake for scraping and leveling of loose or lightly compacted dirt and gravel, and for back fi lling. For improved traction, use wheel weights and/or tire chains.
• Before starting, make sure the material to be graded, such as dirt, is dry enough. Squeeze some in your hand and if it forms a ball that does not crumble, the material may be too wet for raking.
• Drive the tractor at a speed which fi ts conditions and the type of work being performed. When leveling with the rake, a slower speed will allow loose material to be more evenly deposited in low spots.
• For light back fi lling work, the rake assembly can be reversed by rotating it 180 degrees. This allows you to back up with your tractor and push dirt to fi ll larger holes.
• Do not back the rake into piles of dirt or gravel at high speed.
RAKE CAN BE
ROTATED 24
DEGREES IN
EITHER DIRECTION PIVOT PLATE
24º 24º
FIGURE 6
MAINTENANCE/STORAGE
CUSTOMER RESPONSIBILITIES
• Read and follow the maintenance schedule and the maintenance procedures listed in this section.
Fill in dates as you
complete regular service.
Bef Ev ery season
Bef ore stor
X
X X
Service Dates
CHECK FOR LOOSE FASTENERS
• Before each use make a thorough visual check of the rake for any bolts and nuts which may have loosened.
Retighten any loose bolts and nuts.
CLEANING
• Wipe off or wash off loose dirt from the rake after each use to help prevent rust.
6
STORAGE
• Remove all dirt and rust and touch up with paint to help prevent rust.
• Store inside in a clean, dry area.
PARTS
REPAIR PARTS FOR MODEL 486.24537 SLEEVE HITCH ROCK RAKE
1
9
8
4
5
7
3
2
6
REF. PART QTY. DESCRIPTION
1
2
3
4
65063
64780
25165
48978
1
1
24
1
Hitch Assembly
Rake Pivot Assembly
Rake Tine
Pivot Pin
5 HA21362 24 Hex Nut, 3/8-16 (Nylock)
REF. PART QTY.
6 43001 24 Hex Bolt, 3/8-16 x 1"
7 43343 1 Hair Cotter Pin, 1/8"
8 48968 1 Slotted Hex Nut, 1"-8
9 46855 1 Cotter Pin, 3/16" x 2"
49526 1 Owner's Manual
7
Get it fixed, at your home or ours!
For repair of major brand appliances in your own home… no matter who made it, no matter who sold it!
1-800-4-MY-HOME SM
Anytime, day or night
(1-800-469-4663) www.sears.com
To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center.
1-800-488-1222
Anytime, day or night www.sears.com
For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself, call Sears PartsDirect
SM
!
1-800-366-PART
6 a.m. – 11 p.m. CST,
(1-800-366-7278) 7 days a week www.sears.com/partsdirect
To purchase or inquire about a Sears Service Agreement:
1-800-827-6655
7 a.m. – 5 p.m. CST, Mon. – Sat.
Para pedir servicio de reparación a domicilio, y para ordenar piezas con entrega a domicilio:
1-888-SU-HOGAR SM
(1-888-784-6427)
Au Canada pour service en français:
1-877-LE-FOYER SM
(1-877-533-6937)
HomeCentral
SM
® Registered Trademark / ™ Trademark of Sears, Roebuck and Co.
® Marca Registrada / ™ Marca de Fábrica de Sears, Roebuck and Co.
© Sears, Roebuck and Co.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project