SE210

Sound Isolating™ Earphones

Combining Hi-Definition

MicroSpeakers and a stylish sound isolating design to deliver full range audio free from background noise, the Shure SE210 is an ideal portable listening device upgrade. An included modular cable and interchangeable Sound

Isolating™ sleeves provide a comfortable, personalized fit.

The carrying case further enhances the portability of these lightweight earphones.

Three suggested methods for wearing the earphones are illustrated below.

©2006, Shure Incorporated

27EN3243 (Rev. 2) Printed in U.S.A.

Grasp the body of earphone and gently twist to remove.

Note: Do not pull on cable to remove earphone.

If the earphone seems to be lacking in low frequency response (bass), check the tightness of the seal between the earphone and your ear, or try one of the other sleeve options.

Over the ear in back

Over the ear in front

Straight down in front

Cable

Sleeve

Tighten the cable and take up slack by raising the cable sleeve.

Your earphones come with a selection of sleeves. Make sure the sleeve you choose is easy to insert into your ear, fits comfortably, and is easy to remove from your ear.

Soft Flex Sleeves

In small, medium, and large sizes.

Made from pliable rubber.

Soft Foam Sleeves

When using the foam sleeves, compress the sleeve between your fingers before inserting it into the ear canal.

Hold the earphone in place for about ten seconds while the foam expands and creates a tight seal.

Triple-Flange Sleeves

If desired, the sleeve stem may be shortened. Use sharp scissors to carefully trim the stem to the desired length.

Note: carefully slide sleeve over earphone nozzle barb for a secure grip.

Warning: Do not push the earphone sleeve beyond the ear canal opening.

To replace sleeve, carefully remove old one and slide new sleeve over nozzle barb. If any part of the nozzle is exposed, sleeve is not properly installed.

Replace sleeves if they do not grip the nozzle tightly

Nozzle Barb

Sleeve Sleeve Over Barb

If you notice a change in sound quality, remove the sleeve and check the nozzle of your earphone. If nozzle is blocked, clear obstruction by using wire loop end of cleaning tool.

Wire Loop

Cleaning

Tool

Nozzle

When cleaning, do not force any object through the earphone

nozzle! This will damage the earphone sound filter.

• Deluxe Carrying Case

• Fit Kit: contains soft foam, soft flex, and triple flange sleeves plus cleaning tool

• Stereo Extension Cable - 3 ft. (91 cm)

ACCESSORIES

For information about earphone accessories (listed below) and other

Shure products visit: www.shure.com

• Replacement Sleeves

• Carrying Cases

• Adapters

• Extension Cables

• Push To Hear (PTH)

• Volume Control

Transducer type

Sensitivity (at 1kHz)

Impedance (at 1kHz)

DC Resistance

Frequency Range

Input connector

Net weight

Operational temperature

Storage temperature

Balanced-armature drivers

114 dB SPL/mW

26 W

19 W

25Hz - 18.5kHz

3.5 mm (1/8 in.) gold-plated stereo plug

29g (1 oz)

-18° C to 57° C (0° F to 135° F)

-29° C to 74° C (-20° F to 165° F)

Earphone

SE210

User Guide

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446

Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414

Asia, Pacific:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

Careful maintenance ensures a tight seal between the sleeve and nozzle, improving sound quality and product safety.



Keep the earphones and sleeves as clean and dry as possible.



To clean sleeves, remove them from earphones, gently rinse in warm water and air dry. Foam sleeves require a longer drying time. Inspect for damage and replace if necessary.

Ear sleeves must be completely dry before reusing.

 Wipe the earphones and sleeves with mild antiseptic to avoid infections. Do not use alcohol-based disinfectants.

 Do not expose earphones to extreme temperatures.

 Replace the sleeves if they do not fit properly.

CERTIFICATION

Eligible to bear CE marking.

Conforms to European EMC Directive 89/336/EEC.

Meets applicable tests and performance criteria in

European Standard EN 55103 (1996) Parts 1 and 2, for residential (E1) and light industrial (E2) environments.

Those who use earphones regularly for extended periods of time often find custom-fit molded sleeves offer the best comfort and sound isolation.

Ask a Hearing Health Care Professional about creating custom molded sleeves for your earphones. For more information, contact:

Sensaphonics Hearing Conservation Toll Free: (877) 848-1714

660 N. Milwaukee Avenue In Chicago: (312) 432-1714

Chicago, IL 60622 e-mail: [email protected]

www.sensaphonics.com