Samsung WEP420 - Headset - Over-the-ear User`s guide

Quick Start Guide
Samsung
Bluetooth® Headset
WEP420
Before using your headset
Check the accessories
Charge your headset
Thank you for purchasing the Samsung Bluetooth
Mono Headset WEP420. We hope you will be
delighted with its operation.
Take a moment before you get started to
familiarize yourself with your new headset.
Make sure you have the following items with your
headset:
Charge the headset's battery fully before using
the headset for the first time.
Charging Cradle, Travel Adapter, User’s Guide
1 Insert your headset into the slot of the
Earhook
Get connected in 4 quick steps
Charge your headset
Put your headset in pairing mode
Turn on Bluetooth on your phone and
pair with headset
Test and use
The items supplied with your headset may vary, depending
on your country or service provider.
charging cradle.
Multi-Function
button
Volume control
buttons
Earpiece
Indicator light
Headset cover
3 Plug the travel adapter into the electrical
outlet.
• Charge the headset until the red light on the
headset turns to blue.
• The headset will be fully charged in
approximately 2 hours.
4 Remove the travel adapter from the charging
• Bluetooth version: 2.0 (compatible with devices of
Bluetooth version 1.1 or higher)
• Supported Bluetooth Profiles:
- Headset Profile
- Hands-Free Profile
cradle.
2 Plug the travel adapter into the jack on the
charging cradle.
• The headset cannot be used while charging.
• Use only a Samsung-approved charger or adapter.
Microphone
Start here
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
Internet Address:
http://www.samsungmobileusa.com/
accessories
Customer Care Center:
1-888-987-4357
Put your headset in
pairing mode
Turn on Bluetooth on your
phone and pair with headset
Before you can use your headset, you must pair it
with your phone.
1 Set your Bluetooth phone to discover the
1 Ensure that the headset is off (see Turn
headset on/off on the reverse side of this guide).
2 Press and hold the Multi-Function button until
the indicator light turns on in blue
(approximately 8 seconds).
headset by following your phone's guide.
Typically, the steps involve going to the Settings,
Connection, or Bluetooth menu on your
phone and then selecting the option to discover
Bluetooth devices.
Your phone will find the Samsung WEP420
headset and ask if you want to pair with it.
Confirm this by pressing the Yes or OK key.
2 Enter a passkey or PIN, 0000 (4 zeros), then
press the Yes or OK key.
Guide No.: GH68-12483A
04/2007.Rev.1.1
Test and use
Your phone and headset are now paired and
ready to make and receive calls. To confirm
they are operating properly, make a call:
Using your WEP420
1 Place the headset over your ear.
See Wear the headset on the reverse
side of this guide.
2 On your phone, make a call to the number
you want.
3 If your phone and headset are successfully
paired, you will hear ringing on the headset.
After you have successfully paired your phone
and headset, you do not need to repeat these
initial setup steps each time you use the
headset.
See Features and Functions Guide
on the reverse side of this guide
for information on using your
WEP420.
Features and
Functions Guide
SAMSUNG
Bluetooth® Headset
WEP420
Important:
Be sure to first follow the
Quick Start Guide on
the reverse side of this guide
to complete initial setup
of your headset.
Turn the headset on/off
Wear the headset
Use the ear hook
To turn the headset on,
Press and hold the Multi-Function button for
4 seconds until you see 4 blue flashes on the
indicator light, then release.
You will hear a tone and see the indicator light
flashes while the power is on
(see Meaning of the indicator light of this guide).
Wear the headset on your ear.
In general, you will get better performance
when there are no obstructions
(including parts of your body)
between the headset
and the phone.
Depending on what ear you are going to wear the
headset, simply adjust the ear hook accordingly
To turn the headset off,
Press and hold the Multi-Function button for
4 seconds until you see blue and red flashes on the
indicator light, then release.
You will hear series of 2 tones and see the indicator
light stops flashing.
Left
Make calls
Make a voice activated call
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
Internet Address:
http://www.samsungmobileusa.com/
accessories
Customer Care Center:
1-888-987-4357
Use enhanced features
End a call
If the phone’s voice recognition feature is on, you can
make a voice activated call.
Close the headset cover.
1 Press and hold the Multi-Function button. You will hear
When a call comes in, the headset sounds the ring tone and
flashes the blue indicator twice. Choose either of the
following ways to answer the call:
• When the headset cover is closed, open the cover.
• When the headset cover is open, press the Multi-Function
button.
the voice-activation tone.
2 Say the name of the person you wish to call.
Depending on your phone, this feature may not be
supported.
Redial the last number
Press the Multi-Function button. When you release the
button, the phone dials the last dialled or received
number.
Depending on your phone, how to redial the last number
may vary.
Right
Answer a call
Adjust the volume
Press [+] on the side of the headset to increase the volume
level and press [-] to decrease the volume level.
Enhanced features are available for phones that support the
Hands-Free Profile and enhanced features.
• Reject a call
When you receive a call, close the headset cover or press
and hold the Multi-Function button.
Depending on your phone’s setting or type, you may only
be able to mute the ringer or this feature may not be
supported.
• Answer a second call
When your phone notifies you of another incoming call while
you are on a call, press and hold the Multi-Function button to
answer the second call.
You can switch between calls by pressing and holding it.
Depending on your phone, this feature is not supported.
Troubleshooting
My phone does not find my headset.
Make sure the blue indicator light on your
headset turns on when your phone is
searching for devices.
My headsest worked before but now it is
not working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone.
If the Bluetooth feature has been turnned off
or was turned on only temporarily, you may
need to restart the Bluetooth feature.
If you have confirmed the Bluetooth feature is
on in your phone, pair your phone and
headset again.
Meaning of the indicator light
Tone
Status
Flashes in
blue every
8 seconds.
Light
Quick series
of 2 tones.
(Active mode
starts.)
The headset is in Active mode.
Flashes in
blue every 3
seconds.
Quick series
of 2 tones.
(Standby
mode starts.)
The headset is in Standby mode.
Flashes in
red.
5 tones every
20 seconds.
The battery of the headset is
low.
• The headset is waiting
for a call.
• The headset can be in
Standby mode up to 70
hours.*
• There is less than 10% of
battery power left. Recharge
the battery.
• Place a call on hold
While you are on a call, press and hold the Multi-Function
button. To retrieve the call, press and hold the Multi-Function
button again. Depending on your phone, this feature may not
be supported.
• The headset has an active
call in progress.
• You can talk up to 4 hours.*
*Depending on the phone type and usage, the actual time
may vary.