High Performance HD LED Monitor
UML-463-90
en
User Manual
High Performance HD LED Monitor
Table of Contents | en
3
Table of contents
1
Safety
4
1.1
Important safety instructions
4
1.2
Safety precautions
5
1.3
Important notices
5
1.4
Customer support and services
9
2
Unpacking
11
2.1
Parts List
11
3
Access and connections
12
3.1
Monitor views
12
3.2
Rear panel exploded view
13
3.3
Connectors
14
3.4
Remote control
15
3.5
Remote Control Battery Installation
15
4
Description
16
5
Installing the Monitor
17
5.1
Ventilation
17
5.2
Installing accessories
17
5.2.1
Wall mount installation
17
5.2.2
Desktop Installation
17
5.3
Connecting Power
18
5.4
Connecting the Composite Video Signal to the Monitor
18
5.5
Connecting the Y/C (S-Video) Signal to the Monitor
18
5.6
Connecting Audio to the Monitor
19
5.7
Connecting the PC Signal to the Monitor
19
5.7.1
VGA Connection
19
5.7.2
HDMI Connection
19
5.7.3
DVI Connection
20
5.7.4
DisplayPort
20
5.8
Single / Multiple Monitor Configuration
20
5.9
Connecting to the network (LAN)
21
6
Navigating the Monitor
23
6.1
Navigating the Control Panel
23
6.2
Using the Monitor On-screen Display (OSD)
24
6.3
On-screen Display Menus
25
6.4
Picture Menu
25
6.5
Sound Menu
27
6.6
Screen Menu
28
6.6.1
PAP Availability
30
6.7
Setting Menu
31
7
Power Management
34
8
Troubleshooting
35
9
Maintenance
36
10
Technical data
37
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
4
en | Safety
High Performance HD LED Monitor
1
Safety
1.1
Important safety instructions
Read, follow, and retain for future reference all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions before operating the unit.
1.
Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions
provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist
fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol
cleaners.
2.
Heat Sources - Do not install the unit near any heat sources such as radiators, heaters,
stoves, or other equipment (including amplifiers) that produce heat.
3.
Ventilation - Any openings in the unit enclosure are provided for ventilation to prevent
overheating and ensure reliable operation. Do not block or cover these openings. Do not
place the unit in an enclosure unless proper ventilation is provided, or the manufacturer's
instructions have been adhered to.
4.
Water - Do not use this unit near water, for example near a bathtub, washbowl, sink,
laundry basket, in a damp or wet basement, near a swimming pool, in an outdoor
installation, or in any area classified as a wet location. To reduce the risk of fire or
electrical shock, do not expose this unit to rain or moisture.
5.
Object and liquid entry - Never push objects of any kind into this unit through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire
or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled
with liquids, such as vases or cups, on the unit.
6.
Lightning - For added protection during a lightning storm, or when leaving this unit
unattended and unused for long periods, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to the unit from lightning and
power line surges.
7.
Controls adjustment - Adjust only those controls specified in the operating instructions.
Improper adjustment of other controls may cause damage to the unit. Use of controls or
adjustments, or performance of procedures other than those specified, may result in
hazardous radiation exposure.
8.
Overloading - Do not overload outlets and extension cords. This can cause fire or
electrical shock.
9.
Power cord and plug protection - Protect the plug and power cord from foot traffic,
being pinched by items placed upon or against them at electrical outlets, and its exit from
the unit.
10. Power disconnect - Units have power supplied to the unit whenever the power cord is
inserted into the power source. The power cord is the main power disconnect device for
switching off the voltage for all units.
11. Power sources - Operate the unit only from the type of power source indicated on the
label. Before proceeding, be sure to disconnect the power from the cable to be installed
into the unit.
–
For battery powered units, refer to the operating instructions.
–
For external power supplied units, use only the recommended or approved power
supplies.
–
For limited power source units, this power source must comply with EN60950.
Substitutions may damage the unit or cause fire or shock.
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
–
Safety | en
5
If unsure of the type of power supply to use, contact your dealer or local power
company.
12. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
13. Damage requiring service - Unplug the unit from the main AC power source and refer
servicing to qualified service personnel when any damage to the equipment has occurred,
such as:
–
the power supply cord or plug is damaged;
–
exposure to moisture, water, and/or inclement weather (rain, snow, etc.);
–
liquid has been spilled in or on the equipment;
–
an object has fallen into the unit;
–
unit has been dropped or the unit cabinet is damaged;
–
unit exhibits a distinct change in performance;
–
unit does not operate normally when the user correctly follows the operating
instructions.
14. Replacement parts - Be sure the service technician uses replacement parts specified by
the manufacturer, or that have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical shock, or other hazards.
15. Safety check - Safety checks should be performed upon completion of service or repairs
to the unit to ensure proper operating condition.
16. Installation - Install in accordance with the manufacturer's instructions and in accordance
with applicable local codes.
17. Attachments, changes or modifications - Only use attachments/accessories specified by
the manufacturer. Any change or modification of the equipment, not expressly approved
by Bosch, could void the warranty or, in the case of an authorization agreement, authority
to operate the equipment.
1.2
Safety precautions
Danger!
High risk: This symbol indicates an imminently hazardous situation such as “Dangerous
Voltage” inside the product.
If not avoided, this will result in an electrical shock, serious bodily injury, or death.
Warning!
!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily injury.
Caution!
!
1.3
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of damage to the unit.
Important notices
Copyright
This manual is the intellectual property of Bosch Security Systems and is protected by
copyright.
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
6
en | Safety
High Performance HD LED Monitor
All rights reserved.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Closed Circuit Television Equipment, UL
2044. UL Certification does not cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED
FUNCTIONS OF THIS PRODUCT.
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information Technology Equipment, UL
60950-1. UL Certification does not cover the performance or reliability of the security or
signaling aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATED
FUNCTIONS OF THIS PRODUCT.
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:
–
this device may not cause harmful interference, and
–
this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These
limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his expense.
Intentional or unintentional modifications, not expressly approved by the party responsible for
compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet
is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No.
004-000-00345-4.
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The
unit may fall, causing serious injury and/or serious damage to the unit. Use only with the
cart, stand, tripod, bracket, or table specified by the manufacturer. When a cart is used,
use caution and care when moving the cart/apparatus combination to avoid injury from tipover. Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination
to overturn. Mount the unit per the manufacturer's instructions.
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
Safety | en
7
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at
least 3 mm in each pole, into the electrical installation of the building.If it is needed to open
the housing for servicing and/or other activities, use this all-pole switch as the main
disconnect device for switching off the voltage to the unit.
Coax grounding:
–
Ground the cable system if connecting an outside cable system to the unit.
–
Connect outdoor equipment to the unit's inputs only after this unit has had its grounding
plug connected to a grounded outlet or its ground terminal is properly connected to a
ground source.
–
Disconnect the unit's input connectors from outdoor equipment before disconnecting the
grounding plug or grounding terminal.
–
Follow proper safety precautions such as grounding for any outdoor device connected to
this unit.
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors, location of discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
Disposal - Your Bosch product was developed and manufactured with high-quality material
and components that can be recycled and reused. This symbol means that electronic and
electrical appliances, which have reached the end of their working life, must be collected
and disposed of separately from household waste material. Separate collecting systems are
usually in place for disused electronic and electrical products. Please dispose of these units
at an environmentally compatible recycling facility, per European Directive 2002/96/EC
Electronic Surveillance - This device is intended for use in public areas only. U.S. federal law
strictly prohibits surreptitious recording of oral communications.
Environmental statement - Bosch has a strong commitment towards the environment. This
unit has been designed to respect the environment as much as possible.
Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid
electrostatic discharge. NOTE: Wear required grounded wrist straps and observe proper ESD
safety precautions when handling the electrostatic-sensitive printed circuit boards.
Fuse rating - For security protection of the device, the branch circuit protection must be
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC
Section 60).
Grounding and polarization - This unit may be equipped with a polarized alternating current
line plug (a plug with one blade wider than the other blade). This safety feature allows the
plug to fit into the power outlet in only one way. If unable to insert the plug fully into the
outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for
earth grounding). This safety feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally certified electrician to replace the
obsolete outlet. Do not defeat the safety purpose of the grounding plug.
Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive
force or shock may damage the unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially regarding clearance from
power and lightning conductors and transient protection, must be in accordance with NEC725
and NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily accessible disconnect device in the
building installation wiring.
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
8
en | Safety
High Performance HD LED Monitor
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.
Power resupply - If the unit is forced to power down due to exceeding the specified operating
temperatures, disconnect the power cord, wait for at least 30 seconds, and then reconnect
the power cord.
Power lines - Do not locate the display near overhead power lines, power circuits, or electrical
lights, nor where it may contact such power lines, circuits, or lights.
Rack-mount
–
Ventilation - Do not place this unit in a built-in installation or rack without proper
ventilation or adhering to the manufacturer's instructions. The equipment must not
exceed its maximum operating temperature requirements.
–
Mechanical loading - Properly mount the equipment in a rack to prevent a hazardous
condition due to uneven mechanical loading.
SELV
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should
only be connected to other SELV circuits.
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting the
SELV circuit to the Telephone Network Voltage (TNV) circuits.
System ground/Safety ground
The system ground is only used to comply with safety standards or installation practices in
certain countries. Bosch does not recommend connecting system ground to safety ground
unless it is explicitly required. However, if the system ground and safety ground are connected
and grounding loops are causing interference in the video signal, use an isolation transformer
(available separately from Bosch).
Caution!
!
Connecting System ground to Safety ground may result in ground loops that can disrupt the
CCTV system.
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security
Systems cannot be held liable for any damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security Systems recommends multiple,
redundant recording systems, and a procedure to back up all analog and digital information.
Notice!
This is a class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
Informations FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux
conditions suivantes :
–
cet appareil ne peut pas provoquer d'interférence nuisible et
–
cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y
compris les interférences qui pourraient influer sur son bon fonctionnement.
AVERTISSEMENT : Suite à différents tests, cet appareil s’est révélé conforme aux exigences
imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la
Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont destinées
à fournir une protection raisonnable contre les interférences nuisibles quand l'appareil est
utilisé dans une installation commerciale. Cette appareil génère, utilise et émet de l'energie
de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme aux
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
Safety | en
9
instructions, générer des interférences nuisibles aux communications radio. L’utilisation de ce
produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas
échéant, l’utilisateur devra remédier à ces interférences à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision,
qui procédera à une opération corrective. La brochure suivante, publiée par la Commission
fédérale des communications (FCC), peut s’avérer utile : How to Identify and Resolve Radio-TV
Interference Problems (Comment identifier et résoudre les problèmes d’interférences de radio
et de télévision). Cette brochure est disponible auprès du U.S. Government Printing Office,
Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.
NOTE!
This manual has been compiled with great care and the information it contains has been
thoroughly verified. The text was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the user guide can change without
notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user guide and the product
described.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
1.4
Customer support and services
If this unit needs service, contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.
Service Centers
USA
Repair CenterTelephone: 800-566-2283
Fax: 800-366-1329
E-mail: repair@us.bosch.com
Customer Service
Telephone: 888-289-0096
Fax: 585-223-9180
E-mail: security.sales@us.bosch.com
Technical Support
Telephone: 800-326-1450
Fax: 585-223-3508 or 717-735-6560
E-mail: technical.support@us.bosch.com
Canada
Telephone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East, Africa Region
Repair Center
Telephone: 31 (0) 76-5721500
Fax: 31 (0) 76-5721413
E-mail: RMADesk.STService@nl.bosch.com
Asia Region
Repair Center
Telephone: 65 63522776
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
10
en | Safety
High Performance HD LED Monitor
Fax: 65 63521776
E-mail: rmahelpdesk@sg.bosch.com
Customer Service
Telephone: 86 (0) 756 7633117 or 86 (0) 756 7633121
Fax: 86 (0) 756 7631710
E-mail: customer.service@cn.bosch.com
Warranty and more information
For additional information and warranty queries, please contact your Bosch Security Systems
representative or visit our website at www.boschsecurity.com.
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
2
Unpacking | en
11
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in the Parts List below are included. If any items are missing,
notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit and must be
used if returning the unit for service. Save it for possible future use.
2.1
Bosch Security Systems
Parts List
Quantity
Description
1
UML-463-90 Color LED Flat Panel Monitor
1
Installation manual (printed booklet, English version)
1
Installation manual (CD-ROM, multi-language version)
2
Power Cords, 3-wire with grounded plug 1.8 m (6 ft) long:
–
one with a U.S plug type
–
one with a European Continental plug type
1
DVI-D to DVI-D cable, 1.8 m (6 ft)
1
VGA to VGA (D-Sub) cable, 1.8 m (6 ft)
1
Remote control
2
AAA batteries
User Manual
2013.07 | v1.0 | F.01U.286.147
12
en | Access and connections
High Performance HD LED Monitor
3
Access and connections
3.1
Monitor views
1023.68
578.27
573.27
1018.68
Figure 3.1: Front (with dimensions)
58.24
111.8
61
Figure 3.2: Side (with dimensions)
539
M6
CS
x4P
440
441.2
400
Figure 3.3: Back (with dimensions)
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
3.2
Access and connections | en
13
Rear panel exploded view
1
9
8
7
6
5
4
3
2
Figure 3.4: Rear panel exploded view
Ref.
Button
Description
1
IR sensor,
Receives the command signals from the remote control. Detects
ambient light ambient lighting conditions around the display and adjusts screen
sensor and
brightness automatically when the Ambient Light Sensor function is
LED
activated. Indicates the operating status of the monitor:
Indicator
- Lights up green when power is turned on.
- Lights up red when display is turned off.
- Lights up red when display is in Power Save High mode.
- Flashes red when display is in Power Save Low mode.
- Off when power is turned off.
2
LED
Indicates the operating status of the monitor:
Indicator
- Lights up green when power is turned on.
- Lights up red when display is turned off.
- Lights up red when display is in Power Save High mode.
- Flashes red when display is in Power Save Low mode.
- Off when power is turned off.
3
Bosch Security Systems
Power
Turn monitor power On/Off
User Manual
2013.07 | v1.0 | F.01U.286.147
14
en | Access and connections
High Performance HD LED Monitor
4
Increases the value when in the
Scrolls right in the OSD.
OSD.
Increases audio volume.
5
Decreases the value when in the
Scrolls left in the OSD.
OSD.
Decreases audio volume.
6
Adjusts the value when in the
Scrolls up in the OSD.
OSD.
7
Adjusts the value when in the
Scrolls down in the OSD.
OSD.
Activates the Auto Adjustment
function when in PC mode.
8
MENU
Selects the on-screen display (OSD).
9
VIDEO
Selects the signal to be displayed.
SOURCE/
Serves as the “Enter” function for OSD menus.
ENTER
3.3
Connectors
RS-232C-OUT
RS-232C-IN
1
2
3
4
5
6
7
8
9 10 11 12
13 14
15
16 17
18 19
20
21
22
23
Figure 3.5: Connectors
Ref.
Connector
Ref.
Connector
1
RJ-45
13
VGA OUT
2
RS-232 IN (for firmware update)
14
VGA IN
3
RS-232 OUT (for firmware update
15
AUDIO IN - AUDIO 2
4
DISPLAY PORT IN
16
AUDIO IN - AUDIO 3
5
DVI-D OUT
17
AUDIO OUT (R/L)
6
DVI-D IN
18
IR IN
7
HDMI IN 2
19
IR OUT
8
HDMI IN 1
20
SPEAKERS (R/L)
9
VIDEO IN (COMPONENT)
21
AC SWITCH ON/OFF
10
VIDEO IN (S-VIDEO)
22
100 - 240 VAC IN
11
VIDEO OUT (Composite, BNC)
23
100 - 240 VAC OUT
12
VIDEO IN (Composite, BNC)
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
3.4
6
Ref.
Button
Description
1
POWER
Turns power on and off.
ON/OFF
7
3
15
Remote control
1
2
Access and connections | en
8
9
2
Input
Selects a signal source to display.
3
Exit
Exits the OSD menu.
4
Arrow Keys
Moves the cursor down, up, left, and right in the OSD.
Vol + / Vol -
Increases/decreases audio volume.
5
Enter.
Accepts a selection in an OSD menu.
6
Info
Displays the settings of the selected input.
7
Numeric
Function as numeric buttons when the OSD menu is
buttons
active.
(1-9)/Input
Functions as input source buttons when the OSD menu
source
is inactive.
4
10
5
11
NOTE: SDI and MULTIMEDIA functions are not available
with this display.
8
MENU
Displays the OSD Main menu. Press to return to the
Main menu from anywhere in the OSD menus.
9
Numeric
Performs as a numeric button when the OSD menu is
buttons
active.
(0)/MUTE
Mutes the sound when the OSD menu is inactive.
10
Up/down keys
Moves the cursor up and down in the OSD.
11
Multi-media
No function.
keys
3.5
Remote Control Battery Installation
1.
Turn the remote over (buttons facing down) and push down on the cover and slide it off.
2.
Insert two (2) new AAA alkaline batteries, matching the batteries to the (+) and (-) marks
inside the battery case.
3.
Slide the battery cover back into place.
1
1
2
2
Figure 3.6: Remote Control Battery Replacement
Note: Replace batteries when required or at least once a year. Dispose of used batteries
properly.
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
16
4
en | Description
High Performance HD LED Monitor
Description
The Bosch UML-463-90 High Performance LED monitor is a 1080p Full HD resolution color
monitor ideal for use with digital video recorders (DVRs), and with PC applications. The
monitor features a color LCD flat-screen panel with a 46-inch viewable picture area. The
monitor features a wide range of horizontal and vertical viewing angles that provide
comfortable, clear viewing – whether you mount it to a wall, ceiling or on a desktop.
You can access the monitor control functions from the push buttons and the on-screen display
(OSD) menus. Refer to Access and connections, page 12 for descriptions of the connectors and
push buttons available on each model.
Feature overview
–
Full HD 1920 x 1080 resolution
–
Precise color reproduction
–
HDMI, DVI, VGA, S-Video inputs
–
Super-slim bezel for seamless tiled wall mounting
–
High contrast ratio of 3500:1
Refer to Technical data, page 37 for the complete description of all features and
specifications.
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
5
Installing the Monitor | en
17
Installing the Monitor
This chapter outlines the procedures to install the monitor. A qualified service person should
install the monitor and adhere to all local codes.
5.1
Ventilation
To prevent overheating, ensure the ventilation openings on the rear of the monitor are not
covered.
5.2
Installing accessories
The monitors are designed to be mounted to a wall using mounting accessories that are sold
separately. The monitor can also be placed on a desktop using mounting desktop stands that
are also sold separately. See the following chapters for the relevant installation descriptions.
If necessary, refer to the Bosch Security Systems, Inc. Web site or contact your local customer
support representative for more information.
5.2.1
Wall mount installation
The monitor can be wall-mounted using the mounting holes and a suitable wall mount or
swivel/tilt mount. Use UL Listed mounting standards, and ensure the mounts are strong
enough to bear the weight of the monitor. Refer to the following figure for the dimensions of
the wall mounting holes.
400 mm
400 mm
Figure 5.1: Wall mounting
5.2.2
Desktop Installation
Connect the two stands to the base of the monitor as follows:
Bosch Security Systems
1.
Ensure that the power to the monitor and other attached devices are turned off.
2.
Place the monitor with its front facing downward on a soft cloth.
User Manual
2013.07 | v1.0 | F.01U.286.147
18
en | Installing the Monitor
3.
High Performance HD LED Monitor
Assemble the stands by inserting the stand shaft into the stand foot in the correct
direction using the included screws in the accessory packet.
4.
Attach each of the two stands to the base of the monitor using the included screws in the
accessory packet – see following figure.
5.
Once assembled, pick the monitor up carefully and position it upright on its stands
(carefully checking that it is balanced and stable).
Figure 5.2: Mounting desktop stands
5.3
Connecting Power
The Bosch Flat Panel CCTV monitors are delivered with a 3-pole US-style power cord and a 3pole Euro-style power cord. Use the US-style power cord where 120 VAC, 60 Hz power is
available; use the Euro-style power cord where 230 VAC, 50 Hz power is available. The monitor
automatically adjusts to either power input voltage.
5.4
Connecting the Composite Video Signal to the Monitor
There is one (1) BNC connector located on the rear panel of the monitor for composite video
input and one (1) BNC connector for composite video output (Refer to Connectors, page 14).
Note: All video inputs are passive loop-through. The impedance is automatically set to 75 ohm
by the input of the signal on the input connector, while operating in a single connection mode
(refer to , page 20). If a cable is also connected to the output connector, the video signal can
be passed on to another monitor connected to it via the passive loop-through function. Up to
three (3) monitors may be connected in this manner (see also , page 20).
Note: To select AV1, press VIDEO SOURCE/ENTER, and then press the Up or Down arrow
button, on the control panel (beside the MENU button).
5.5
Connecting the Y/C (S-Video) Signal to the Monitor
There is one (1) mini-DIN type connector for the S-Video (Y/C) input on the rear panel (see
Connectors, page 14).
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
Installing the Monitor | en
19
Note: Both Y and C inputs are terminated with 75 Ohm.
Figure 5.3: Y/C Connector pin-out
5.6
Number
Input
1
Ground
2
Ground
3
Y-signal
4
C-signal
Connecting Audio to the Monitor
There are two (2) sets of stereo audio connectors for audio inputs, located on the rear panel.
These audio inputs are not associated with any input terminals on the rear panel, and can be
freely connected to any audio input.
5.7
Connecting the PC Signal to the Monitor
There are several ways to connect the PC signal to the monitor: HDMI, DVI, VGA and DISPLAY
PORT.
5.7.1
VGA Connection
Connect the PC signal using the VGA connector on the rear panel and a VGA cable (D-SUB to
D-SUB).
Figure 5.4: VGA Input
5.7.2
Pin
Description
Pin
Description
Pin
Description
1
Red Video
6
Red Ground
11
Ground
2
Green Video
7
Green Ground
12
SDA (for DDC)
3
Blue Video
8
Blue Ground
13
H-Sync or H+V Sync
4
Ground
9
N/A
14
V-Sync
5
Ground
10
Signal Cable Detect
15
SCL (for DDC)
HDMI Connection
Connect to the HDMI (High Definition Multimedia Input) using a HDMI cable (not supplied).
Figure 5.5: HDMI Input
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
20
en | Installing the Monitor
5.7.3
High Performance HD LED Monitor
DVI Connection
Connect to the digital DVI Input connector by using the supplied DVI-D cable.
Figure 5.6: DVI Input
5.7.4
DisplayPort
Connect the PC signal using the DisplayPort IN connector on the rear panel and a DP cable
(DP to DP).
Figure 5.7: DisplayPort IN
5.8
Single / Multiple Monitor Configuration
1
3
2
4
Figure 5.8: Single Monitor Configuration
Ref
Description
Ref
Description
1
Video Camera
3
Video Out
2
Video In
4
DVR
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
Installing the Monitor | en
21
1
3
2
3
2
2
Figure 5.9: Multiple Monitor Configuration
Ref
Description
1
Video Camera
2
Video In
3
Video Out
See also
–
5.9
Single / Multiple Monitor Configuration, page 20
Connecting to the network (LAN)
These connection steps require experience with working with the OSD – see Navigating the
Monitor, page 23.
Connect to the LAN
1. Connect an RJ45 cable to the corresponding ports on the monitor, and to your LAN
switch or router.
2.
Enter the OSD menu Setting > Control Setting. Select LAN.
3.
Enter the next OSD menu Setting > Network Settings.
4.
If you are in a DHCP environment, select DHCP > Execute and press ENTER. Once done,
the IP Address, Subnet mask, Default gateway, Primary DNS, and Secondary DNS
settings will be displayed.
5.
If you are not in a DHCP environment, select Manual > Execute and press ENTER.
Contact your IT administrator for information on the IP Address, Subnet mask, Default
gateway, Primary DNS, and Secondary DNS settings and enter them accordingly.
6.
To save the settings and return to the previous menu, select Execute then press ENTER.
Controlling the display
Once you have the correct IP address for your display and the display is on or in standby
mode, you can use any computer that is on the same local area network to control the display.
1.
Bosch Security Systems
Enter the IP address of the display in the address bar of your browser and press Enter.
User Manual
2013.07 | v1.0 | F.01U.286.147
22
en | Installing the Monitor
2.
High Performance HD LED Monitor
The setting page appears:
–
Information: Shows information of the display. It is for information only. There are
no items that can be set.
–
Picture & Sound: Provides options for picture and sound adjustments.
–
Screen: Provides options related to display adjustments.
–
Setting: Provides options for advanced display adjustments.
–
Mail Report: Provides options for setting up email accounts to receive status or error
reports sent from the display.
–
Network: Provides options for:
- manually setting the monitor IP address
- obtaining an IP address from a DHCP server
- setting/changing the user name and password to secure this network control
system
Notes:
You cannot control the display via the RS-232C connector when LAN control is in use.
It is recommended that you use Internet Explorer versions 7.0 or higher.
If you need to turn on the display from a web page, make sure:
–
the Setting > Control Setting menu is set to LAN
–
the Setting > Power save menu is set to LOW or Of
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
Navigating the Monitor | en
6
Navigating the Monitor
6.1
Navigating the Control Panel
23
Use the control panel to make any necessary OSD adjustments. See the figure below for an
explanation of the control panel.
7
6
5
4
3
2
1
Figure 6.1: Control Panel Buttons
Ref.
Button
Description
1
Power
Display Power (On/Off)
2
Increases the value when in the
Scrolls right in the OSD.
OSD.
Increases audio volume.
3
Decreases the value when in the
Scrolls left in the OSD.
OSD.
Decreases audio volume.
4
Adjusts the value when in the OSD.
Scrolls up in the OSD.
5
Adjusts the value when in the OSD.
Scrolls down in the OSD.
Auto adjusts when in PC mode.
6
Menu
Selects the on-screen display (OSD).
7
VIDEO
Selects the signal to be displayed
SOURCE/ENTER Serves as the “Enter” function for OSD menus
Notice!
This monitor has a special key lock function for both the control panel and remote control to
prevent unintentional operator actions.
Lock/unlock the buttons on the control panel by simultaneously pressing and holding the left
and right arrow buttons on the control panel for 5 seconds.
Lock/unlock the buttons on the remote control by simultaneously pressing and holding the
MENU and left arrow buttons on the control panel for 5 seconds.
Lock/unlock the buttons on both the remote control and control panel by pressing the down
arrow button on the remote control for 5 seconds, and then the ENTER button.
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
24
6.2
en | Navigating the Monitor
High Performance HD LED Monitor
Using the Monitor On-screen Display (OSD)
The LCD is programmed through the on-screen display (OSD) menus and submenus where an
operator can select operating parameters. To access the OSD menus, press the MENU button
on the control panel or on the remote control. Use the buttons on the panel or remote to
make any necessary adjustments to the OSD.
Notice!
When you are navigating through the OSD menus, use the VIDEO SOURCE/ENTER button to
select a menu and use the MENU button to exit a menu.
To set up the signal connection, follow the steps below:
1.
Connect the appropriate Video, S-Video, DVI, HDMI, VGA or DisplayPort signal cable to
2.
Press the Power button to turn on the unit.
3.
Press the VIDEO SOURCE/ENTER button on the control panel (or INPUT on the remote
the monitor.
control) and then the up and down arrow buttons until the correct signal is displayed.
Confirm your selection by pressing the VIDEO SOURCE/ENTER button (or the ENTER
button on the remote control).
(You can also directly choose the desired signal button on the remote control.)
To navigate within the OSD menus, follow the steps below:
1.
Press the MENU button to activate the main menu selections.
2.
Press the up and down arrow buttons to select a menu.
3.
Press the right arrow button to enter the selected menu.
4.
Press the up and down arrow buttons to select a sub-menu item.
5.
Press the left and right arrow buttons to toggle the OSD values.
6.
Press the MENU button to confirm a selection, or to exit the selected menu and to return
7.
Press the MENU button again to exit the OSD menu bar.
to the menu bar.
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
6.3
Navigating the Monitor | en
25
On-screen Display Menus
There are four (4) on-screen menus that allow you to customize your monitor settings. Press
the MENU button (on Control panel or remote) to access the OSD menu.
Icon
Menu
Function
Picture
Adjust relevant picture quality settings. See Picture Menu, page 25.
Sound
Adjust relevant sound settings. See Sound Menu, page 27.
Screen
Adjust relevant screen display settings. See Screen Menu, page 28.
Settings
Resets the factory default settings and adjust the overall monitor
settings. See Setting Menu, page 31
Note: Some of the OSD menu functions may not be available depending on the input source
detected.
6.4
Picture Menu
Access the Picture menu using the MENU button on control panel or remote control.
Figure 6.2: Picture menu
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
26
en | Navigating the Monitor
High Performance HD LED Monitor
Submenu
Definition
Picture Mode
Selects the automatic picture control mode. Choices are:
Standard: applies factory default values.
Vivid: for viewing very bright images.
Cinema: for viewing movies.
Custom: creates your own picture settings. This mode is automatically
selected after you change the settings in the Picture menu.
Backlight
Adjusts LCD backlight intensity of the screen (range 0-100).
Note:
This feature is not available if the Ambient Light Sensor or Adaptive
Contrast function is set to On (see Advanced option in Setting Menu,
page 31).
Contrast
Adjusts the contrast level for video performance (range 0-100).
Brightness
Adjusts the brightness level for video performance (range 0-100).
Chroma
Adjusts the overall color intensity of the screen (range 0-100).
Phase
Adjusts the phase of the picture (range 0-100).
Sharpness
Adjusts the sharpness level for video performance (range 0-100).
Color Temp
Selects the color temperature. Choices are:
11000 K
9300 K
6500 K
Custom (options here are: Red, Green, and Blue)
Noise reduction
Reduces electrical image noise caused by different media players.
Film mode
Optimizes the screen display automatically by detecting picture content
and applying a reverse 3-2 or 2-2 pull-down process. The picture will be
clearer and more natural.
Note:
This function is not available when displaying Picture and Picture (PAP).
This function may not work correctly, depending on the input signal.
Reset
Resets all settings in the Picture menu.
See also
–
2013.07 | v1.0 | F.01U.286.147
Screen Menu, page 28
User Manual
Bosch Security Systems
High Performance HD LED Monitor
6.5
Navigating the Monitor | en
27
Sound Menu
Access the Sound menu using the MENU button on control panel or remote control.
Figure 6.3: Sound menu
Submenu
Definition
Sound mode
Adjusts the sound output from the speakers:
Dynamic: Enhances treble and bass
Standard: Flat settings
Custom: Recalls the customized settings
Treble
Adjusts treble
Bass
Adjusts bass
Balance
Adjusts balance
Surround
Turns the surround mode on or off
Speaker
Sets the audio output source:
Line-Out: Selects the audio output source from AUDIO OUT (R/L) on
connector panel
External: Selects the audio output source from SPEAKERS (R/L) on
connector panel
Internal: Select the audio output source from the internal speakers
Audio Source
Selects the audio input source:
Audio1 connector
Audio2 connector
HDMI1 connector
HDMI2 connector
DisplayPort connector
Reset
Bosch Security Systems
Resets all settings in the Sound menu
User Manual
2013.07 | v1.0 | F.01U.286.147
28
6.6
en | Navigating the Monitor
High Performance HD LED Monitor
Screen Menu
Access the Screen menu using the MENU button on control panel or remote control.
Figure 6.4: Screen menu
Submenu
Definition
PAP Setting
Turns on or off the PIP (Picture in Picture) and PBP (Picture by
(Picture and Picture)
Picture) functions:
Active Picture: For PIP, selects the main or sub picture to operate.
For PBP, selects the left or right picture to operate. Swaps the
main/sub or left/right pictures.
Picture Size: Changes the size of the sub picture.
Picture Position: (PIP only) Changes the position of the sub picture.
Note:
PAP is not available for all signal source combinations. See PAP
Availability, page 30 for more information on supported
combinations.
In PAP mode, only sound from the active picture will be available.
Display wall
H. Monitors/V. Monitors: Sets the number of displays used in the
horizontal/vertical direction.
H. Position/V. Position: Sets the horizontal/vertical position of the
display wall matrix.
Frame Comp.: Adjusts images near the display edges for optimal
demonstration across the display wall.
LED: Turns the power indicator on the display on or off.
Power On Delay: Choose to enable or disable a sequence in turning
on the screen matrix. If enabled, the display will turn on with a
maximum 10 second delay
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
Navigating the Monitor | en
High Performance HD LED Monitor
Aspect
29
Sets the picture’s aspect ratio:
Wide Zoom: Enlarges to fill screen with minimum distortion.
Zoom: Enlarges the picture, keeping the same aspect ratio.
Full: Enlarges the picture horizontally to fill the screen when the
picture source is 4:3 (Standard definition). When the picture source
is 16:9 (High definition), it displays in the same 16:9 aspect ratio.
4:3: Displays all picture sources in 4:3 aspect ratio.
Full 1: Enlarges the picture to fill the screen in the vertical direction,
keeping the same aspect ratio. A black frame may appear around
the picture.
Full 2: Enlarges the picture to fill the screen.
Real: Displays the picture in its original number of dots.
For video signal inputs:
For PC signal input:
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
30
en | Navigating the Monitor
High Performance HD LED Monitor
Adjust screen
Auto Adjustment: Auto synchronizes screen to graphics adaptor.
Phase: Adjusts the monitor’s phase.
Clock Frequency: Adjust the monitor’s clock frequency.
H. Position: Adjust the monitor’s horizontal position.
V. Position: Adjust the monitor’s vertical position.
Freeze
6.6.1
Select On to freeze the displayed image.
PAP Availability
The table below summarizes the availability of the input source combinations for the PIP
feature. (“+” indicates accepted combination, a blank cell indicates the combination is not
valid).
Main Picture Input Source
AV
S-Video
YPbPr
VGA
DVI
HDMI
DisplayPor
t
Sub
Picture
AV
+
+
+
+
S-Video
+
+
+
+
+
+
+
+
+
+
YPbPr
2013.07 | v1.0 | F.01U.286.147
VGA
+
+
DVI
+
+
+
+
+
HDMI
+
+
+
+
+
DisplayPort
+
+
+
+
User Manual
+
+
Bosch Security Systems
High Performance HD LED Monitor
6.7
Navigating the Monitor | en
31
Setting Menu
Use the arrow buttons to make changes and the MENU button to exit submenu.
Figure 6.5: Setting menu
Submenu
Definition
Language
Select a language for the OSD.
Schedule
Date and Time: Sets up current date and time for the monitor’s
internal clock before using the Schedule function.
Clock Display: Sets whether to show the current time which was set.
Input: Sets an input source to display when the display is
automatically turned on next time.
On/Off Timer: Sets when to turn on or off the display.
Note:
Set the current time before setting the On/Off Timer.
When scheduling settings overlap, the Everyday setting takes priority
over other weekly settings.
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
32
en | Navigating the Monitor
Power Save
High Performance HD LED Monitor
Sets the display to enter the power saving mode when there is no
signal detected (see also Power Management, page 34).
Low: All signal sources can enter the power saving mode and wake up
the display.
High: All signal sources can enter the power saving mode, but only a
VGA signal can wake up the display, or you must press the power
button to wake up the display when other source is connected.
Off: If no signal source is detected, the backlight will stay on.
Note:
Serial can bring any mode out of the power saving status.
LAN can bring Low mode out of the power saving status.
Control Setting
RS-232C/LAN: Choose a terminal to control the display.
IR Pass through: Select if multiple displays are connected via RS-232C
cables:
–
Primary: Designate the display as the primary unit for remote
control operation. Only this display will be operated by the
remote control.
–
Secondary: Designate the display as the secondary unit. The
display can not be operated by the remote control, and will only
receive the control signal from the primary display via the RS-232
connection.
Note:
To reset to the default setting (RS-232C), press INFO on the remote
control for 5 seconds
Network Settings
See Connecting to the network (LAN), page 21.
Set Monitor ID
Sets the ID number for controlling the monitor when multiple
monitors are connected under the RS-232C control mode. Each
monitor must have a unique ID number (this will define its position
within the matrix). For example: starting on the top row (working left
to right), the top left monitor can have an ID of 1; when you reach the
end of the row, the next number will refer to the monitor one row
down, starting at the left.
HDMI Control
Uses the HDMI CEC (Consumer Electronics Control) industry standard
protocol to share functionality between connected devices and the
monitor. This means you can send system commands to the monitor
and a connected device using one remote control as follows
–
Connect an HDMI cable between the monitor and a device
equipped with HDMI CEC.
–
2013.07 | v1.0 | F.01U.286.147
Make sure On is selected for this menu option HDMI Control.
User Manual
Bosch Security Systems
High Performance HD LED Monitor
Advanced
Navigating the Monitor | en
33
Auto Detection: Automatically detects available input sources.
Auto Adjustment: Automatically optimizes image display for the VGA
input.
Overscan: Turns the overscan function on or off.
RGB Signal: Sets the type of signal for a piece of video equipment or
PC connected to the HDMI of the display
Image Retention: Automatically displays swift moving patterns to
prevent image retention on the screen.
OSD Rotation: Adjusts the OSD rotation (see product specifications
for models recommended for portrait orientation. Landscape only
models operated in portrait mode may result in premature failure and
will not be covered under the warranty).
OSD Info Box: When turned On, switching signal inputs or changing
timing will show the current input source and resolution on screen.
Select Off to show the information box on screen only when you press
INFO on the remote control.
Adaptive Contrast: Turns the Adaptive Contrast function on or off.
This feature enhances image contrast for dark scenes. (This feature is
not available if the Ambient Light Sensor function is set to On – see
below).
Ambient Light Sensor: When turned On, the image brightness will
adjust automatically as the ambient lighting conditions change.
IR Out: Operate multiple monitors with one IR remote control as
follows:
–
Select IR-Out > On.
–
Point the remote control to the first display with its IR OUT port
connected to the second display’s IR IN port (the second
display’s IR OUT port connects to the third display’s IR IN port,
and so on).
Information
All Reset
Bosch Security Systems
Displays the following monitor information:
–
Date
–
Model Name
–
Serial Number
–
Operating Time
–
Software Version
–
LAN Version
–
IP Address
Returns all settings to factory default values
User Manual
2013.07 | v1.0 | F.01U.286.147
34
7
en | Power Management
High Performance HD LED Monitor
Power Management
This monitor has a power management system to “power down” upon receipt of the display
power management signaling (DPMS) from a DPMS video card.
The DPMS-compliant video card performs this signaling by not sending a horizontal, vertical,
or a sync signal. The monitor enters an appropriate mode through identifying each of the three
(3) modes of the signaling system.
The LED indicator on the back of the monitor signals the current power mode status – see
Rear panel exploded view, page 13.
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
8
Troubleshooting | en
35
Troubleshooting
Problem
Solution
No image displayed on
–
screen
Check that the power cord of the monitor is securely
connected into the wall outlet or grounded extension cable
or strip.
–
Power switch should be in the ON position and the LED lit.
–
Check that the Brightness and/or Contrast adjustments of
the display have not been turned down to minimum levels.
Display image is not
Push the down arrow button to activate the Auto Adjustment
centered, or is too small function.
or too large in the PC
- or -
mode
Adjust the Frequency and Phase in the OSD submenu – see
Screen Menu, page 28.
Vertical or horizontal
Push the down arrow button to activate the Auto Adjust function.
noise is present in the
- or -
picture
Adjust the Frequency and Phase in the OSD submenu.
Incorrect colors
Select a color temperature in the Color Temp menu.
- or Use the Reset function to reset to the default settings.
The error message “Out
PC is operating with either a resolution or timing mode that is not
of Range” is displayed
supported by the monitor. Change the PC timing mode to one of
the valid combinations below:
Bosch Security Systems
–
640 x 480 (60/72/75Hz)
–
720 x 400 (70Hz)
–
800 x 600 (60/75Hz)
–
1024 x 768 (60/75Hz)
–
1280 x 768 (60Hz)
–
1280 x 960 (60Hz)
–
1280 x 1024 (60Hz)
–
1366 x 768 (60Hz)
–
1600 x 1200 (60Hz)
–
1920 x 1080 (60Hz)
User Manual
2013.07 | v1.0 | F.01U.286.147
36
9
en | Maintenance
High Performance HD LED Monitor
Maintenance
To clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or a
soft lint-free cloth. Staining and discoloration may occur if left on the panel for long periods. If
the surface (polarizer) of the LCD panel is dirty or stained, use absorbent cotton or a soft lintfree cloth to remove the residue as follows:
1.
Turn off the monitor and disconnect it from the power supply.
2.
Do not spray any liquid directly on the screen. Dampen a clean, soft, lint-free cloth with
water only (a paper towel or dirty cloth can scratch the screen).
3.
Gently wipe the screen starting from top to bottom, wiping in a downward motion. Do
not damage the screen by pressing too hard.
4.
To avoid streaking, wipe the screen again with another clean, dry, lint-free cloth.
Notice!
If water does not work, use a mild cleaner labeled for use with LCD panels, available at office
supply stores.
Do not use any of the following as a cleaning agent (they may permanently damage the
polarizer due to a chemical reaction):
–
Ketone type materials
–
Ethyl alcohol
–
Ethyl acid
–
Toluene
–
Methyl chloride
–
Ammonia
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
10
Technical data | en
37
Technical data
Electrical
Rated Voltage
120/230 VAC, 50/60 Hz
Voltage Range
100–240 VAC, 50/60 Hz
Frequency
Horizontal: 60–73 KHz
Vertical: 47–63 Hz
Power at Rated Voltage
On = 149 W
Active Off = 0.5 W
Video
Sync Format
PAL/NTSC automatic detection
LCD Panel
LED backlight
Viewable Picture Area
46 in.
Active Display Area
1018.08 x 572.67 mm
(H x V)
(40.08 x 22.55 in.)
Pixel Pitch
0.53025 x 0.53025 mm
(H x V):
(0.02088 x 0.02088 in.)
Resolution1
1920 x 1080
Aspect Ratio
16:9
Display Colors
1073.7 million
Response Time
6.5 ms (typical)
Backlight
50,000 hours
1. Pixel Policy: Bosch monitors follow the ISO 13406-2 Class II standard.
LCD Panel Optical Characteristics
Luminance
450 cd/m2 (typical)
Contrast Ratio
3500:1 (typical)
Viewing Angle
Horizontal/Vertical: 178° (typical)
Video Input
Bosch Security Systems
Composite Video
1.0 Vp-p (0.5–1.5 Vp-p), automatic switching from 75 Ohm unbalanced
(CVBS)
termination to Hi-Z with passive loop-through operation
Y/C (S-video)
0.7 Vp-p (Y-signal), 0.3 Vp-p (C-signal), 75 Ohm termination
Component
Y, Pb, Pr
Digital Inputs
DVI D (1 x) and HDMI (2 x)
User Manual
2013.07 | v1.0 | F.01U.286.147
38
en | Technical data
High Performance HD LED Monitor
VGA (RGB PC)
0.7 Vp-p (0.5–1 Vrms)
Audio Input
2.0 V line level, mono
RGB and DVI
HDMI
640 x 480 (60/72/75 Hz)
640 x 480 (60/72/75 Hz)
720 x 400 (70 Hz)
720 x 400 (70 Hz)
800 x 600 (60/75 Hz)
800 x 600 (60/75 Hz)
1024 x 768 (60/75 Hz)
1024 x 768 (60/75 Hz)
1280 x 768 (60 Hz)
1280 x 768 (60 Hz)
1280 x 960 (60 Hz)
1280 x 960 (60 Hz)
1280 x 1024 (60 Hz)
1280 x 1024 (60 Hz)
1360 x 768 (60 Hz)
1360 x 768 (60 Hz)
1366 x 768 (60 Hz)
1366 x 768 (60 Hz)
1400 x 1050 (60 Hz)
1400 x 1050 (60 Hz)
1600 x 1200 (60 Hz)
1600 x 1200 (60 Hz)
1680 x 1050 (60 Hz)
1680 x 1050 (60 Hz)
1920 x 1080 (60 Hz)
1920 x 1080 (60 Hz)
480i (60 Hz)
480p (60 Hz)
576i (50 Hz)
576p (50 Hz)
720p (25/3050/60 Hz)
1080i (50/60 Hz)
1080p (24/25/30/50/60 Hz)
1080p (24/25 Psf)
Controls
Input
Rear Control Panel
Push-buttons
Remote control
Push-buttons
Video Source
Selects: Component Video, S-video, VGA, HDMI, DVI-D
Menu
Selects on-screen display (OSD), up cursor, down cursor/auto
adjust, left cursor, right cursor
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
High Performance HD LED Monitor
Technical data | en
Power
On/Off
Control Panel Lockout
Multiple push-button combination
39
On-screen Display
Video Mode
Input Source, Screen, OSD, Utility
Indicators (on rear)
LED
Power On (green)
Power Off, Standby (red)
Connectors
Video 1 (AV1)
Composite video: two (2) BNC (1 in, 1 out)
Digital
Two (2) (1 DVI-D in, 1 DVI-D out)
IR
Two (2) (1 in, 1 out)
Display port
One (1) in
HDMI
Two (2) in
VGA
One (1): 1 RGB 15-pin D-sub in, 1 RGB 15-pin D-sub out
Component
One (1): Y, Pb, Pr
Y/C (S-video)
One (1) mini-DIN, 4-pin (1 in)
Audio
1 Audio In: RCA (right/left)
1 Audio In: phono jack
1 Audio Out: RCA (right/left)
1 Speaker Out (right/left)
RS-232
Two (2) (1 in for firmware update, 1 out for firmware update)
Power Input
100 – 240 VAC
Power Output
100 – 240 VAC
Mechanical
Cabinet Material
SECC
Finish
Black
Mount
Wall mounting compatible with standard bracket (optional)
Desk mount (optional)
VESA Mounting Compliance 400 x 400 mm (15.7 x 15.7 in.)
Dimensions (W x H x D)
Monitor
1023.68 x 578.27 x 111.8 mm
(40.30 x 22.77 x 4.4 in.)
Bosch Security Systems
User Manual
2013.07 | v1.0 | F.01U.286.147
40
en | Technical data
With Packaging
High Performance HD LED Monitor
1190 x 754 x 290 mm
(46.85 x 30.08 x 11.42 in.)
Weight
Monitor Weight
25 kg (55.12 lb)
Shipping Weight
30 kg (66.14 lb)
Environmental
Operating Temperature
0°C to +50°C (32°F to 122°F)
Storage Temperature
0°C to +50°C (32°F to 122°F)
Humidity
0% to 90% Relative
2013.07 | v1.0 | F.01U.286.147
User Manual
Bosch Security Systems
Bosch Security Systems B.V.
Torenallee 49
5617 BA Eindhoven
The Netherlands
www.boschsecurity.com
© Bosch Security Systems B.V., 2013