Windsor IMXIE17 10066410 Operating instructions

Carpet Maintainer

Operating instructions (ENG)

MODELS:

IM

10066360

IMIE17

10066550

IMX

10066400

IMXIE17

10066410

IMIE17 AU

10060990

IMXIE17 AU

10061030

IMIE17 UK

10060980

IMXIE17 UK

10061020

Read these instructions before using the machine.

86269870 - T

09/28/09

Machine Data Log / Overview

OVERVIEW

The Carpet Maintainer is designed to maintain carpet using the Quick Dry Carpet Care System. The machine has two counter rotating brushes that scrub chemical into the carpet. The chemicals, iCapsol or Prochem ProCaps, encapsulates the dirt, allowing both to be vacuumed up once the chemical has dried. The brushes also raise the pile of the carpet. The Deluxe models have a solution tank and pump powered spraying system, which applies the chemical to the carpet as the machine is used.

2 86269870 CARPET MAINTAINER

Machine Data Log / Overview. . . . . . . . . . . . . . . . . . 2

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . 4

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 5

Hazard Intensity Level . . . . . . . . . . . . . . . . . . . . . . . 6

Grounding Instructions - . . . . . . . . . . . . . . . . . . . . . . 7

Safety Label Locations . . . . . . . . . . . . . . . . . . . . . . . 8

Operations

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . 9

How The Machines Work . . . . . . . . . . . . . . . . . . . . 10

Quick Dry Carpet Care System Instructions . . . . . . 10

Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . . 11

Transporting A Sprayer. . . . . . . . . . . . . . . . . . . . . . 12

Shut-Down And Storage . . . . . . . . . . . . . . . . . . . . . 12

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Table of Contents

PARTS

Brush. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Brush Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Decal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Electrical 120V . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Electrical 230V . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Frame Deluxe . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Handle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Rear Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Solution Tank - Deluxe . . . . . . . . . . . . . . . . . . . . . 42

Wiring 120V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Wiring 230V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Wiring 120V - Deluxe . . . . . . . . . . . . . . . . . . . . . . 48

Wiring 230V - Deluxe . . . . . . . . . . . . . . . . . . . . . . 50

Suggested Spare Parts . . . . . . . . . . . . . . . . . . . . . 52

Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Maintenance

Brush Cleaning And Maintenance . . . . . . . . . . . . . 14

Motor Replacement & Belt Tensioning . . . . . . . . . . 14

Machine Maintenance. . . . . . . . . . . . . . . . . . . . . . . 16

Machine Troubleshooting . . . . . . . . . . . . . . . . . . . . 17

86269870 CARPET MAINTAINER 3

How to Use This Manual

This manual contains the following sections:

• HOW TO USE THIS MANUAL

• SAFETY

• OPERATIONS

• MAINTENANCE

• PARTS LIST

The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.

Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the

MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual.

The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:

• REF – column refers to the reference number on the parts illustration.

• PART NO. – column lists the part number for the part.

• PRV NO. – reference number.

• QTY – column lists the quantity of the part used in that area of the machine.

• DESCRIPTION – column is a brief description of the part.

• SERIAL NO. FROM – If this column has an (*) and a Reference number, see the SERIAL

NUMBERS page in the back of your manual. If column has two asterisk (**), call manufacturer for serial number. The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustration is shown, it displays the older design.

• NOTES – column for information not noted by the other columns.

NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.

NOTE: The manual part number is located on the lower left corner of the front cover.

The model and serial number of your machine is on the operator's left hand side, side panel of base.

The SAFETY section contains important information regarding hazard or unsafe practices of the machine.

Levels of hazards is identified that could result in product or personal injury, or severe injury resulting in death.

The OPERATIONS section is to familiarize the operator with the operation and function of the machine.

The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition.


Safety

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet. See Grounding Instructions.

Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service.

Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.

Use only as described in this manual. Use only manufacturer's recommended components and attachments.

Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not run machine over cord or allow the rotating brushes to come in contact with the cord. Keep cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.

Do not handle the electrical plug or machine with wet hands.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.

Machine is designed for indoor use only and must not be operated or stored outdoors in wet conditions.

Turn off all controls before unplugging.

This machine is suitable for commercial use, including hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.

SAVE THESE INSTRUCTIONS


Safety

Hazard Intensity Level

The following symbols are used throughout this guide as indicated in their descriptions:

There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY.

The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which could result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine.

Use approved replacement parts.


Safety

This Product Is For Commercial Use Only.

Electrical

In the USA, this machine operates on a standard 15 amp 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.

Extension Cords

If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.

Grounding Instructions -

120V Only

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in "Fig.

A". A temporary adaptor that looks like the adaptor in

"Fig. C" may be used to connect this plug to a 2-pole receptacle as shown in "Fig. B", if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover.

Whenever the adaptor is used, it must be held in place by a metal screw.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.


Safety

Safety Label Locations

The following WARNING LABEL(S) are found on your cleaning unit. These labels point out important Warnings and

Cautions which should be followed at all times. Failure to follow warnings and cautions could result in fatality, personal injury to yourself and/or others, or property damage. Follow these instructions carefully! DO NOT remove these labels.

NOTE: If at any time the labels become illegible, promptly replace them.

WARNING LABEL

PART NUMBER 86220140

PRV 500895


Operations

Technical Specifications

120V

ITEM

Electrical

Nominal Power

Rated Amperage

DIMENSION/CAPACITY

120V

0.5 HP

7 Amps

Brush Width

Brush RPM

17 - 16.5" (430 - 420 mm)

470 RPM

Wheels 3 inches (75 mm) non-marking grey

Dimensions - Weight - Weight

- Deluxe

48 lbs. (22 kg)56 lbs. (25 kg)

Dimensions - Height with handle

Dimensions - Depth

Power Cord

Solution Tank Volume - Deluxe

Pump Pressure - Deluxe

Solution Flow - Deluxe

Spray Jet Size - Deluxe

45.5" (1.16 m)

16 inches (0.4 m)

40 feet (12.2 m)

2 gallon

50 psi

0.1 gpm

.010

230 V

ITEM

Electrical

Nominal Power

Rated Amperage

DIMENSION/CAPACITY

230V

0.5 HP

4 Amps

Brush Width

Brush RPM

17 - 16.5" (430 - 420 mm)

470 RPM

Wheels 3 inches (75 mm) non-marking grey

Dimensions - Weight - Weight

- Deluxe

48 lbs. (22 kg)56 lbs. (25 kg)

Dimensions - Height - with handle

Dimensions - Depth

Power Cord

Solution Tank Volume - Deluxe

Pump Pressure - Deluxe

Solution Flow - Deluxe

Spray Jet Size - Deluxe

45.5" (1.16 m)

16 inches (0.4 m)

40 feet (12.2 m)

2 gallon

50 psi

0.1 gpm

.010

Special Notes:

The sound pressure level at the operator's ear was measured to be 67.7dBA . This was a nearfield, broadband measurement taken on a carpeted floor. This appliance contains no possible source of impact noise.

The instantaneous sound pressure level is below 63 Pa.

The weighted root mean square acceleration at the operator's arms was measured to be below 2.5m/s2 .

This was a tri-axial, third-octave-band measurement made during normal operation on a composite tile floor.

The measurement and related calculations were made in accordance with ISO 5349-1.

NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.


Operations

How The Machines Work

The Carpet Maintainer is designed to maintain your carpet using the Quick Dry Carpet Care System. By using the Carpet Maintainer in conjunction with iCapsol or Prochem ProCaps chemical solution, you can perform a regular light cleaning and grooming of your carpet very quickly, and have the carpet dry and ready for traffic within 20 minutes.

The handle movement flexibility allows the machine to clean under low furniture. There is a hand operated on/ off switch and auto-handle lock keeping the handle in an upright position. This unit is equipped with a safety feature that when unplugged from the wall or the handle dropped, will automatically reset to the off position .

The debris tray is used to catch unwanted carpet debris and should be cleaned regularly and prior to transporting.

This appliance conforms with international and national safety directives: EN55014-2, EN5504-1, EN61000-3-

2/3-3, EN60335-1/2-10/2-69/2-67. IEC 60335-1/2/10/2-

67/2-69. LVD 73/23/EEC.

Deluxe

This unit is equipped with an onboard spray pump and solution tank. By using the onboard spraying system a light treatment of chemical can be applied to the carpet and brushed in during a single pass of the machine.

Quick Dry Carpet Care System

Instructions

Test for colorfastness in an inconspicuous area before use.

1.

Vacuum carpet to remove loose soil.

2.

Dilute iCapsol or Prochem ProCaps at 8oz. per gallon of water (1:16) into the solution tank.

3.

Pre-spray carpet to be cleaned at a rate of 600-

1000 sq. ft. per gallon of diluted solution. Do not over wet.

4.

No dwell time is required. Do not allow chemical to dry before brushing.

5.

Brush treated area to emulsify soils using the

Windsor iCapsol or other carpet-brushing machine.

6.

Allow to dry until dry to touch (approximately 20 minutes) before opening area to traffic.

7.

Vacuum carpet when fully dry to remove encapsulated soil.

Tips: Pre-treat carpet spots with iCapsol Interim cleaning solution. Work on a manageable area and do not allow cleaning solution to dry on carpet before brushing.

Deluxe

The Deluxe is provided with a removable solution tank.

To remove tank for filling and cleaning, press the gray release button on the blue coupler located at the top of the tank. Next remove upper straps from mounting pegs. The tank will now freely separate from the machine base. After filling tank remount to machine by reversing the process mentioned above.

The proper 1:16 dilution ratio can be achieved by adding one pint (16 oz.) of recommended chemical and slowly filling the tank with water (2 gallons). Adding water slowly will help prevent foaming.

To achieve a coverage rate of 600-1000 sq. ft. per gallon using the onboard sprayer, spray solution only during the forward stroke of operation. Use the backstroke to brush the chemical into the carpet.


Machine Operation

Pre-Run Inspection

Perform a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Check the rating plate to confirm voltage and frequency is the same as the power supply. NOTE:

A 10% variation in voltage is acceptable.

Starting Machine

NOTE: Perform pre-run machine check before operating machine.

FOR SAFETY: Before starting machine, make sure that all covers are in place and secured properly.

1.

Connect the machine to a power supply.

2.

Release the handle lock.

3.

(a) Press green button to power on the machine,120V only.

(b) Set black on/off switch to "on" position, 230V only.

4.

Press green button to start brushes.

After applying a light spray of diluted interim carpet cleaner onto the carpet using a pressurized tank sprayer, commence cleaning by pushing and pulling the machine slowly over the wetted carpet.

Move the machine in multiple directions and overlapping strokes.

For best results use Windsor iCapsol or Prochem

ProCaps products.

Operations

Starting Machine - Deluxe

NOTE: Perform pre-run machine check before operating machine.

FOR SAFETY: Before starting machine, make sure that all covers are in place and secured properly.

1.

Connect the machine to a power supply.

2.

Release the handle lock.

3.

(a) Press green button to power on machine, 120V only.

(b) Set black on/off switch to "on" position, 230V only.

4.

Press green button to start brushes.

5.

Press and hold blue button to spray chemical.

Once machine is plugged in spray function is operational.

Apply a light spray of diluted interim carpet cleaner onto the carpet using the onboard spraying system. Spray chemical while pushing the machine forward. Brush the chemical into the carpet while pulling the machine slowly over the wetted carpet. Move the machine in multiple directions and overlapping strokes.

For best results use Windsor iCapsol or Prochem

ProCaps products.

Flammable materials can cause an explosion or fire.

Do not use flammable materials with this machine.


Operations

Transporting A Sprayer

This machine has the capability to mount a small pumpup sprayer.

Transporting Chemical - Deluxe

This machine has the capability to mount chemical bottles or trigger sprayers to the back of the solution tank.

This Machine is not intended to carry more than 30 pounds. Carrying more than 30 pounds could cause damage to the machine.

Shut-Down And Storage

1.

Flush the spray jet and tank with hot water (Deluxe only)

2.

After flushing, uncouple quick disconnect to prevent water from dripping out of front jet.

3.

(a) Press red button to power off machine

120V only.

(b) Set black on/off switch to "off" position

230V only.

4.

Lock handle in the upright position.

5.

Disconnect the power cord from the power supply.

Wind the power cord around the cable holders on the handle.

6.

Remove the brushes for cleaning. See Brush

Cleaning and Maintenance section.

7.

Clean debris tray.

The machine is now ready for storage until the next use. Make sure to store your equipment in a dry place to prolong the life of your machine. Storage outdoors or unprotected could cause damage to your machine or internal parts, therefore voiding your warranty.


Components

1A

1B

2

1A

1B

8

2

Operations

5

4

6 iCapsol Mini

1.

A. Stop Switch (red-120V only)

B. On/Off Switch (black-230 only)

2.

Start Switch (green)

3.

Brushes

4.

Handle Release

3 3

7

iCapsol Mini Deluxe

5.

Tank

6.

Strainer

7.

Jet

8.

Spray Pump Switch

4


Maintenance

Brush Cleaning And Maintenance

After each session of carpet cleaning, the brushes and the brush housing should be cleaned. Before cleaning or changing the brushes, always unplug the machine from the power supply.

Brushes are removed without tools. After handle is in locked position, tilt the machine back and rest on handle. To release brush from spring clip pull spring clip away from brush end cap. Lift brush out of machine.

The brushes may be soaked in warm or hot water using mild detergent, and then rinsed with warm water.

NOTE: Brushes with crushed bristles can often be restored to original condition by soaking in hot water.

Keep brushes clean and free from debris. Rotate brushes after every use as this will increase the life span of the brushes and ensure even wear.

Before reinstalling brushes, clean out machine brush housing and hopper by wiping with a clean damp cloth.

Motor Replacement & Belt Tensioning

1.

Disconnect machine power supply.

2.

Detach quick disconnect hose from top of solution tank. (Deluxe Only)

3.

Remove elastic straps and solution tank. (Deluxe

Only)

4.

Remove two dome screws and dome assembly.

6.

Mark left and right on the lift cams.

7.

Remove the two cam bolts. This will also free the lift cams.

NOTE: There are four plastic bushings that the handle pivots on, leave them on the motor clamps.

LIFTING CAM

RIGHT

LIFTING CAM

LEFT

8.

Remove the handle assembly.

9.

Unscrew the wiring grommet from the main cover, and set retaining bracket and screw aside.

10. Remove the the front and back screws and move the main cover to the side.

NOTE: The handle assembly and cover are still attached to the frame by wiring. Be careful not to pinch wiring when reassembling.

11. Remove the (2) plastic finger guards.

12. Remove the motor clamps and lift brackets.

DOME

MOTOR CLAMP

CIRCUIT BREAKER

& BOOT

COVER

LIFT BRACKET

MOTOR

WIRING GROMMET

5.

Remove the circuit breaker boot and push the circuit breaker clear of cover.

PLASTIC FINGER

GUARD (2)


Maintenance

13. Unplug motor wires. Loosen end cap screws, 1 full turn.

END CAP

SCREWS

HANDLE MOUNT

ASSEMBLY

ROTATE MOTOR

RIGHT HAND

GEAR DRIVE

ACCESS HOLE

FOR LOWER

SCREW

PULLEY

BELT

MOTOR

BELT

PULLEY

14. Remove belts.

15. Lift motor out of housing, and remove pulleys. Set pulleys aside for re-installation.

16. Take the new motor and loosen the screws in the long rear drive end cap. This allows the end cap to swivel +/- 20 degrees. Do not remove the end cap screws, only back them off 1 full turn.

17. Put the motor in the cradle on the frame. Place pulleys onto motor shaft's. Loop the drive belts onto motor drive pulleys.

18. Place lift brackets on motor, align over pins. Put the motor/clamp mount assembly over the motor and lightly snug the retaining bolts. The motor must be able to turn inside the motor clamps. If clamps are too tight to move the motor by hand, loosen clamp bolts.

LIFT BRACKETS

MOTOR CLAMPS ROTATE MOTOR

LEFT HAND

GEAR DRIVE

19. Turn the motor body inside motor clamps so that the left hand gear drive pivots upwards. Take all of the slack out of the left hand gear drive belt and snug left hand motor clamp bolts.

20. While holding the motor stationary, turn the right hand gear drive downward so that the gear drive housing touches the setscrew in the frame. This set screw was installed on the assembly line and establishes the correct position for the motor.

21. Tighten the screw in the long gear drive cap.

22. Tighten all four motor clamp bolts.

23. Check both belts for equal tension. The belts should not sag under their own weight, however, should flex easily when squeezed with fingers. If the tension is clearly unequal, loosen the motor mount bolts and retighten. This will equalize the belt tension from on side to the other.

24. Reinstall finger guards

25. Reinstall lift brackets with top surface lip on inside.

26. Reinsert circuit breaker through hole in cover, reattach cover, circuit breaker boot, and wiring grommet.

27. Verifying lifter cams are on correct side, reattach handle assembly.

28. Reattach dome cover.

29. Reattach solution tank and reconnect top hose.

(Deluxe Only)


Maintenance

Machine Maintenance

The Maintainer requires very little maintenance. Wipe down the machine periodically with a clean cloth. DO

NOT spray water directly over the top of machine.

Deformation of the brush bristles can result in unbalanced running and excessive vibrating or jumping.

The machine is fitted with a circuit breaker. In the unlikely event of overloading, the circuit breaker will automatically trip. It can be reset after approximately 30 seconds (or when the machine cools down) by pushing the set button located on the cover housing.

Daily Maintenance

1.

Clean and inspect brushes.

2.

Clean and inspect brush housing, debris tray and machine. Rinse debris tray if needed.

3.

Inspect power cord for wear or damage. This cable will lie on wet carpet. To prevent electrical shock replace cords that are frayed or have cracked insulation immediately.

4.

Flush the tank, pump and spray jet with hot water

(Deluxe only).

5.

Clean Strainer.

Periodic Maintenance

1.

Check all handles, switches, electrical cables and connections on your machine for damage. Repair or replace immediately.

2.

Inspect and/or replace brushes.

Replace brushes when main bristles are worn to the same level as the yellow indicator bristles.

3.

Check spray pattern. Clean or replace jet if the pattern is blocked or uneven

Annual Maintenance

1.

Check all bearings for noise and wear.

2.

Check motor for operation.

3.

Check overall machine for operation.

4.

Check belts for wear and change belts every second year.


Maintenance

Machine Troubleshooting

PROBLEM

No power to machine

CAUSE

Tripped electrical circuit breaker in fuse box of building

Faulty power cord

SOLUTION

Check building circuit breaker

Replace power cord

Power switch failure or relay failure

Replace power switch or relay

Tripped circuit breaker

Internal wiring problem

Reset circuit breaker. Higher amp draw may indicate faulty parts. Find parts not moving freely and correct as needed.

With machine unplugged, check for and correct, any loose wire connections.

Electrical Shock

Faulty rectifier

Equipment not grounding

Receptacle not grounded

Interal electrical problem

Faulty circuit breaker

Replace rectifier

Follow grounding instructions, pg 2-3

Have an electrician inspect the building's wiring

Check for any loose wire connections, replace any items that are short circuiting

Replace circuit breaker

Nuisance tripping of circuit breaker

Brush not turning or scrubbing

Mechanical problem

Worn brush motor brushes

Power to motor but motor does not run

Worn brush motor brushes

Bearing squealing or grinding in brush housing

Machine will only run if the green (on) switch is continuously held down

Faulty brush motor/gear box

Belt failure

Worn bearings

Defective red (off) switch.Sends constant "off" signal.

Test circuit breaker for continuity. Higher amp draw may indicate faulty parts. Find parts not moving freely and repair or replace.

Replace brush motor/gear box

Replace belts

Replace brushes, check commutator

Replace brushes, check commutator

Replace worn bearing

Replace or reconnect wire to red (off) switch

No flow or uneven flow from jet

(Deluxe only)

Clogged jet

Weak flow from clean jet

(Deluxe only)

Clogged strainer

Pump runs but no flow from jet

(Deluxe only)

Disconnect coupling at solution tank

Clean or replace jet

Clean strainer

Attach the quick coupling to the solution tank


Notes


PARTS


Brush

4

2

9

5

3

1

3

6

7

8


Brush

8

9

6

7

REF PART NO.

PRV NO.

QTY

3

4

1

2

5

86217340

86172630

86172870

86214850

270130

57314

70898

86224670 730396

12544

1

2

6

2

2

DESCRIPTION

COVER, BELT, RIGHT

NUT, M4, LK, SST

SCR, M4X14, PHMS, DIN7985 SST

SPRING, BRUSH CLIP

ASSY, BRUSH & HUB

86217330 270129

86216070 12535

86172840

86214840

70886

12534

1 COVER, BELT, LEFT

2 ASSY, BRUSH DRIVE

6 SCR, M5X10, PHS, FHD, SST

ASSY, BRUSH, COAST

SERIAL NO.

FROM

NOTES

INCLUDES

86214840


Brush Lift


6

1

2

3

4

5

Brush Lift

REF PART NO.

PRV NO.

QTY

3

4

1

2

5

6

86215580 141042

86172700

86215750

86224760

86215740

86223620

67606

09156

73997

09155

67605

DESCRIPTION

2 BRACKET, CROSSOVER PUSH

4 RING, E-TYPE, 5MM ID, DIN6799

4 BRG, FLNG, 6MM IDX7MM LONG

4 SPRING, COM, 18.28 OD X 25L

4 BRG, FLNG, 6MM IDX24MM LONG

2 ROD, LIFTING

SERIAL NO.

FROM

NOTES


Decal

2A

2B


1

Decal

REF PART NO. PRV NO. QTY

1 86221620 501260

2A 86244630 501190

2B 86244920 501247

1

1

1

DESCRIPTION

LABEL, CHEMICAL INSTR.

LABEL, MAIN, ICAPSOL MINI

LABEL, PROCAP PROCHEM

SERIAL NO.

FROM

NOTES

DELUXE ONLY

WINDSOR ONLY

PROCHEM ONLY


Electrical 120V

31

29

30

15

6

15

7

8

17

18

16

19

23

23

20

20

22

2

1

14

26

27

6

7

8

28

DELUXE ONLY

27

13 12

26

25

DELUXE ONLY

5

9

8

10

11

21

26

3

4

5

86269870 CARPET MAINTAINER

Electrical 120V

REF PART NO. PRV NO. QTY DESCRIPTION

1 86002010 14942

2 86217120 23729

3 86214770 38370

4 86214780 38371

5 86225070 38372

6 86198450 20005

7 86225320 78601

8 86173100 70935

1 BOOT, 3/8 CIRCUIT BREAKER

1 CORD SET, 18/3 X 40FT SJT

1 ASM RED BUTTON W/BEZEL

1 ASM GREEN BUTTON W/BEZEL

2 SWITCH, ITW, MICRO

2 CLAMP, 5/16 NYLON

1 TIE, CABLE NYLON

4 SCR, M3X6, BSHCS, SST

9 86291470

10 86291490

-

-

11 86291880 -

12 86216800 20110

1 BRKT, MTR BRKT, SWITCH, CVR

1 COVER, SWITCH, BRKT


1 CLIP, WIRE

13 86277600 70882 1 SCR, M4X20, PPHMS, SST

14 86215670 140839 1 BREAKER, 8A VDE CIRCUIT

15 86172880 70901

16 86173200 70950

5

1

SCR, M4X6, BSHCS, SST


17 86225850 87517

18 86223400 67516

19 86223390 67488

20 86173210 70951

21 86291860 -

22 86222670 05248

23 86216740 20040

24 OPEN -

25 86013570

26 86299320

27 86313930

28 86295190

29 86295150

30 86295180

31 86314630

-

-

-

-

-

-

-

2

1

1

4

1

1

2

-

2

2

1

2

1

1

1

WASHER, M3, FL, ISO7089, SST

RELAY, 15A 120VAC MINI

RECTIFIER, 50A 600V BRIDGE


SWITCH, 125VAC SP NC ROLLER

PLATE, BASE, ELECTRICAL MTG

CLAMP, 17,7 NYLON

-

SWITCH, PUSHBUTTON, BL, DLX

LABEL, GROUND SYMBOL

SWITCH, W/COUPLER, N.C.

ASM, BUTTON, BLUE, W/BEZEL

ASM, BUTTON, RED, W/BEZEL

ASM, BUTTON, GREEN, W/BEZEL

SWITCH, W/COUPLER, N.O.

SERIAL NO.

FROM

*(1)

*(1)

*(1)

*(1)

*(1)

NOTES

DELUXE ONLY

DELUXE (QTY 3)

DELUXE ONLY

*See Serial Number Page

**Call Manufacturer For Serial Number.


Electrical 230V

28

1

2

5

4

4

29

8

15

8

12

25

22

23

24

18

17

3

4

19

31

7

6A

6B

5

16

31

30

DELUXE ONLY

3

14 13

20

27

33

32

26

21


Electrical 230V

REF PART NO.

PRV NO.

QTY

3

4

1

2

86299810

86295180

86313930

86172880

5 86198450

6A 86217200

6B 86310620

7 86002010

8

9

86216740 20040

86215910 140972

10 86225080

11 86173110

72152

70936

12 86173100

13 86216800

14 86277600

15 86302450

70935

20110

70882

-

-

-

-

70901

20005

23738

-

14942

16 86215710 141046

17 86173210 70951

18 86222670

19 86225320

05248

78601

20 86291490

21 86291880

22 86223420

23 86173200

-

-

67622

70950

24 86223460

25 86225850

26 86291860

27 86299320

28 86299830

29 86264940

30 86295190

31 86299320

32 86173100

33 86291470

67499

87517

-

-

-

27051

-

-

70935

-

DESCRIPTION

1 SWITCH, BLACK, ROCKER, DPST

1 ASM, BUTTON, GREEN, W/BEZEL

1 SWITCH, W/COUPLER, N.C.


2 CLAMP, 5/16 NYLON

1 CORD SET, EURO 1MM X 40 BLACK

1 CORD SET, 18/3 X 40FT AUS

1 BOOT, 3/8 CIRCUIT BREAKER

2 CLAMP, 17,7 NYLON

1 BRKT, MTR BRKT, SWITCH

1 SWITCH, 125VAC SP NC ROLLER



1 CLIP, WIRE

1 SCR, M4X20, PPHMS, SST

1 ASM, FILTER, EMI MAIN

1 BREAKER, 5A VDE CIRCUIT


1 PLATE, BASE, ELECTRICAL MTG

4 TIE, CABLE NYLON

1 COVER, SWITCH, BRKT

2 SCR, M3X12, BSHCS, ISO7380, SS

1 RELAY, 10A 230V MINI SPDT

1 SCR, M416, BSHCS, SST

1 RECTIFIER, 50A 1000V BRIDGE

2 WASHER, M3, FL, ISO7089, SST

1 SWITCH, 125VAC SP NC NO-ROLLER

1 LABEL, GROUND SYMBOL

1 COVER, SWITCH, PVC

1 CABLE TIE, 11.38" UL/CSA

2 ASM, BUTTON, BLUE, W/BEZEL


2 SCR, M3X6, BSHCS, ISO7380, SST

1 BRKT, MTR BRKT, SWITCH

SERIAL NO.

FROM

*(1)

NOTES

DELUXE (QTY 3)

WAS 86223390

DELUXE ONLY


**Call Manufacturer For Serial Number


Frame

1

2

3

4

5

6

7


Frame

REF PART NO.

PRV NO.

QTY

5

6

7

3

4

1

2

86225340

86217930

86214820

86277600

86222360

86214830

86173050

78952

34450

05262

70882

58009

05263

70920

DESCRIPTION

1 TRAY, IRENEW MINI

1 FRAME, 3.5", SINGLE MOTOR

1 ASSY, COVER, INSULATION


1 NUT, M4X0.7, U-CLAMP, 3MM PANEL

1 ASSY, DOME, INSULATION


SERIAL NO.

FROM

NOTES


Frame Deluxe

9

6

7

8

10

5

11

14

2

12

13

1

3

4


Frame Deluxe

REF PART NO.

PRV NO.

QTY

7

8

5

6

3

4

1

2

86173050

86173040

86011610

86217930

86225340

86012550

86004570

86012440

9 86197520

10 86233090

11 86290790

12 86277600

13 86222360

14 86214830

70920

70919

-

-

34450

78952

-

44067

-

40011

20016

70882

58009

05263

DESCRIPTION

3 SCR, M4 X 40 PPHMS, SS

3 SCR, M4 X 10 SHCSB BUTHD

1 ASSY, COVER, INSULATION, DLX

1 FRAME, 3.5, SINGLE MOTOR

1 TRAY, IRENEW MINI

1 JET, PROMAX, 11001

1 JET BODY, MINI PROMAX BODY

1 MANIFOLD, SPRAYER, DLX, IMX

1 HOSEBARB, 1/8MPT X 1/4 DL

1 CLAMP, 1/4 ID HOSE

1 SCR, M6 X 8, CP, BLK

1 SCR, M4 X 20, PHMS, SST

1 NUT, M4 X 0.7, U-CLAMP, 3MM PANEL

1 ASSY, DOME, INSULATION

SERIAL NO.

FROM

NOTES


Handle

20

1

25A

25B

26

19

18

17 16

15A

15B

14

3

23A

23B

3

24

21

5

3

4

13

2

12

11

6A

6B

22

8A

8B

10

9

7


Handle

REF PART NO.

PRV NO.

QTY

3

4

1

2

86011380

86059580

86277600

86217230

5 86217220

6A 86218680

6B 86218510

7 86173070

8A 86013820

8B 86222650

-

38354

9 86173180 70948

10 86221800 279992

11 86172640 57507

12 86221810 279993

13 86224970 730382

14 86223640 38332

-

38324

70882

38326

38325

38357

38321

70922

15A 86218690

15B 86218520

38358

38322

16 86224680 730414

17 86223450 67620

18 86012940

19 86172820

20 86216890

21 86172870

22 86294260

-

70883

38327

70898

-

23A 86305580 -

DESCRIPTION

1 GRIP, HANDLE

1 CONSOLE, BOTTOM


1 CORD HOOK, UPPER

2 CORD HOOK, LOWER

1 HANDLE, EXTRUSION, LEFT

1 HANDLE, EXTRUSION, LEFT

4 SCR, M5X12, CSK.OVL,ISO 7047,SS

1 PIVOT CASTING, DLX

1 PIVOT CASTING

2 SCR, 10M8X55, SHLD, BLK

1 LIFTING CAM, LEFT

2 NUT, M8, LK, SST

1 LIFTING CAM, RIGHT

1 STRAP, SPRAYER HOLD DOWN

4 RUBBER STRAP HOOK

1

1

1

1

1

2

1

2

4

1

HANDLE, EXTRUSION, RIGHT

HANDLE, EXTRUSION, RIGHT

SPRING, COMP, 11.56D X 19.05L

RETAINER, SPRING, CORD HOOK

SCR, KA40X35, PT OVAL, WN1412, PL

SCR, M5X20, PPHMS, SST

CONSOLE, TOP

SCR, M4X14, PPHMS, ISO7045, SST

SCR, M5X12, W/LOCTITE

CONSOLE, BOTTOM, DLX

SERIAL NO.

FROM

**

23B

24 86308740

25A 86293340

25B

86293330

86305590

26 86299750

-

-

-

-

-

1

4

1

1

1

CONSOLE, BOTTOM

SCR, M5X30,CSK, OVL, ISO7047,SS

CONSOLE, TOP

CONSOLE, TOP

GRIP, HANDLE

**

**

**

**

**

NOTES

DELUXE ONLY

DELUXE ONLY

DELUXE ONLY

DELUXE 110V

& BASIC 110V

DELUXE 230V

& BASIC 230V

DELUXE 110V

& BASIC 110V

DELUXE 230V

& BASIC 230V


**Call Manufacturer For Serial Number


Hopper

4

5

1

2

3

2

6

7


REF PART NO.

PRV NO.

QTY

5

6

7

3

4

1

2

86214790

86173040

86214800

86173080

86216310

86172630

86217450

41584

70919

41585

70933

140977

57314

270709

DESCRIPTION

1 ASM, GUIDE, HOPPER


1 ASM, HOPPER FRAME & PLATE

1 SCR, 4.2 X 9.5, TAP, ZN

1 BUMPER, STOP, HOPPER

1 NUT, M4, LK, SST

1 COVER, FRONT, HOPPER

Hopper

SERIAL NO.

FROM

NOTES


Motor

1

5

4

3

6

7

8

14

13 12

9

10

11

15A

15B

16

17

2

38

18


Motor

REF PART NO. PRV NO. QTY

1 86215320 11058

2 86215300 11055

3 86215960 140979

4 86173310 87499

5 86173060 70921

6 86217890 34451

7 86217590 62647

8 86173090 70934

9 86222530 66869

10 86291480 -

11 86173100 70935

12 86173180 70948

13 86224620 730376

14 86215950 140978

15A 86222200 54206

15B 86222210 54216

DESCRIPTION

1 BELT, HTD, 15MM X 300, 60 TOOTH, RH

1 BELT, HTD, 15MM X 325, 65 TOOTH, LH

1 BRKT, MTR MOUNT, RH

4 WASHER, SPRING LK, 6MM, SS

3 SCR, SHCS, M6X60, SST

4 FLANGE, BRG, PIVOT

2 CVR PLATE, 1.5MM THK, PLASTIC

1 SCR, SHCS, M6X80, SST

1 PEDAL, FOOT, HANDLE RELEASE

1 BRKT, FOOT PEDAL, SWITCH


1 SCR, 10M8X55, SHLD, BLK

1 SPRING, TORSION, 19.38 OD

1 BRKT, MTR MOUNT, LH

1 MOTOR, SINGLE, 3.5" DIA

1 MOTOR, 230V, IMIE

86216180 141057

16 86223780 70896

17 86223340 64124

18 86018550 70949

1 BRUSH SET, 120V VAC, IM

2 SCR, M4X8, CP, BLK

2 PULLEY, HTD, 5MM, 15W, 18T

1 SCR, M6X20, CP, BLK

SERIAL NO.

FROM

NOTES

120V ONLY

230V ONLY

120V & 230V,

NOT SHOWN


Rear Wheel

40

5

4

3

2

1


Rear Wheel

REF PART NO.

PRV NO.

QTY

3

4

1

2

5

86172790

86011020

86173300

86172640

70867

86216450 140942

89202

87495

57507

DESCRIPTION

2 SCR, SHCS, M8X50, ISO4762, BLK

4 BUSHING, 11.25MM X 8.0MM, SST

2 WHEEL, 3" DIA. CUSHION RUBBER

4 WASHER, M8, FL, ISO7089, SST

2 NUT, M8, LK, ISO7040, SST

SERIAL NO.

FROM

NOTES


Solution Tank - Deluxe

25

1

-A-

2

3

4

5

6

16

8

19

26

21

15

-A-

20

24 9

12

31

23

21

-B-

13

14A

14B

13

22

-C-

17

7

31

29

15

30

27

-B-

-C-

19

28

-D-

18

-D-

10

11


Solution Tank - Deluxe

REF PART NO.

PRV NO.

QTY

7

8

5

6

3

4

1

2

86299710

86299720

86012500

86219230

86225300

86013850

86172820

86012570

-

-

-

41581

75489

-

70883

-

9 86012940

10 86216780

11 86172870

12 86217560

-

27909

70898

41577

13 86012520 -

14A 86201120 250-78A

14B 86201110

15 86240520

250-78

40097

16 86172990

17 86013840

18 86217550

19 86012530

20 86012560

21 86233090

22 86012970

23 86006770

24 86224970 730382

25 86012470 -

26 86290030

27 86290010

-

-

28 86290020

29 86299320

30 86225320

31 86010640

-

-

78601

87016

70913

-

41576

-

-

20016

-

70323

DESCRIPTION

1 CPLR, BODY, 1/4" BARB, GRY

1 CPLR, PNL MNT, 1/4" BARB, GRY

1 SEAL, COUPLER, EPDM RUBBER

1 HOSE, SUCTION, TANK, DELUXE

1 TANK, DLX (MACH)

3 WASHER, M6, FNDR, SS

3 SCR, M5 X 20, PHMS, ISO7045, SST

1 STRAP, CHEMICAL BOTTLES, DLX

5 SCR, KA40X35, PT OVL, PL

2 CLAMP, TUBE 1/4”

2 SCR, M4X14 PHMS, SST

1 COVER, PUMP, TOP, DELUXE

2 GASKET, SEAL, NEOPRENE, RBR

1 PUMP, 220/240V 50HZ FLOJET

1 PUMP, 110/120 60HZ FLOJET

4 HOSEBARB, 1/8MPT X 1/4 90D

3 SCR, M6 X 12 BHCS, ISO 7380, SS

1 WASHER SPRING LCK, SMM

1 COVER, PUMP, DELUXE

2 GROMMET, 9.3MM ID X 23MM OD

1 STRAINER, SMALL, 60 MESH

4 CLAMP, 1/4 ID HOSE

2 WASHER, M5, FNDR, SS

1 SCR, 10-32 X 1/4 PHTR PLTD


1 CAP, 2-1/4, POWER GRIP

1 HOSE, 3/8OD X 1/4ID URTHN X 30”




1 TIE-CABLE, NYLON

2 WASHER, #10 LOCK EXT STAR SS

SERIAL NO.

FROM

NOTES

230V

110V


Wiring 120V

GRN

ORG

N.C.

RED

ORG

BLK

WHT

GRN

N.O.

GREEN

1

44

5

GRN

BLK

BLK

2

N

RECTIFIER

WHT

WHT

RELAY

8

6

4

2

7

5

3

1

BLK

RED

PUR

ORG

ORG

3

ORG

ORG

BLK

4

RED

MOTOR


N.C.

Wiring 120V

REF PART NO.

PRV NO.

QTY

3

4

1

2

5

86218820

86226220

86226260

86226270

86226280

41563

880462

880468

880469

880471

DESCRIPTION

1 HARNESS, MAIN

1 WIRE, 10" BLK/18 76040

1 WIRE, 15" ORG/18 76040 X 76040

1 WIRE, 18" ORG/18

1 WIRE, 9" BLK/18 76040 X 76040

SERIAL NO.

FROM

NOTES


Wiring 230V

46

GRN

ON/OFF

BLK

RED

ORG

BRN

BLU

GRN

N.O.

GREEN

5

BLK

2

BLK

GRN

N

RECTIFIER

WHT

RELAY

8

6

4

2

7

5

3

1

BLK

6

RED

PUR

ORG


1

ORG

ORG

7

BLU

3

ORG

4

BLK

N.C.

BRN RED

MOTOR

Wiring 230V

REF PART NO.

PRV NO.

QTY

5

6

7

3

4

1

2

86218880

86226220

86226260

86226270

86226280

86302450

86310150

41594

880462

880468

880469

880471

-

-

DESCRIPTION

1 HARNESS, MAIN, 230VAC

1 WIRE, 10" BLK/18 76040

1 WIRE, 15" ORG/18 76040 X 76040

1 WIRE, 18" ORG/18

1 WIRE, 9" BLK/18 76040 X 76040


1 ASSY, FILTER, EMI MOTOR

SERIAL NO.

FROM

NOTES


Wiring 120V - Deluxe

5

BLK

2

BLK

N

RECTIFIER

WHT

WHT

RELAY

8

6

4

2

7

5

3

1

BLK

BLK

GRN

RED

PUR

ORG

8

BLK

BLK

BLK

WHT

GRN

N.O.

BLUE

ORG

ORG

N.C.

RED

BLK

BLK

BLK

WHT

WHT

N.O.

GREEN

N.O.

BLUE

WHT

1

ORG

3

ORG

ORG

BLK

4

RED

MOTOR

N.C.

PUMP MOTOR

WHT

BLK

GRN

9

7

6



REF PART NO.

PRV NO.

QTY

7

8

5

6

9

3

4

1

2

86218820

86013120

86013090

86013110

86013950

41563

86226220 880462

86226260 880468

86226270 880469

86226280 880471

-

-

-

-

DESCRIPTION

1 HARNESS, MAIN

1 WIRE, 10" BLK/18 76040

1 WIRE, 15" ORG/18 76040 X 76040

1 WIRE, 18" ORG/18

1 WIRE, 9" BLK/18 76040 X 76040

1 HARNESS, PUMP HOUSING, DLX

1 WIRE, 9.5" GRN/18

1 WIRE, 4 W/WIRE JOINT, BLK

1 WIRE ASSY, W/2 PIN CONN, DLX

SERIAL NO.

FROM

NOTES



N.O.

BLUE

5

BLK

2

BLK

GRN

6

N

RECTIFIER

WHT

RELAY

8

6

4

2

7

5

3

1

WHT

BLK

RED

PUR

ORG

11

BLK

BLK

GRN

BLK

ON/OFF

BLK

1

7

ORG

ORG

BLU

3

ORG

4

BLK

N.C.

BRN RED

WHT

RED

ORG

BLU

BRN

MOTOR

N.O.

BLUE

BLK

BLK

N.O.

GREEN

WHT

WHT

PUMP MOTOR

WHT

BLK

12

GRN

10

9



REF PART NO.

PRV NO.

QTY

7

8

5

6

3

4

1

2

86218880

86226220

86226260

86226270

86226280

86302450

86310150

OPEN

9 86306770

10 86013090

11 86306760

12 86013950

41594

880462

880468

880469

880471

-

-

-

-

-

-

-

DESCRIPTION

1 HARNESS, MAIN, 230VAC, IMIE

1 WIRE, 10" BLK/18 76040 X 76040

1 WIRE, ORG/18 76040 X 76040

1 WIRE, 18" ORG/18 76040 X 76040

1 WIRE, 9" BLK/18 76040 X 76040


1 ASSY, FILTER, EMI MTR

-

1 HARNESS, PUMP HOUSING, DLX 230

1 WIRE, 9.5" GRN/18

1 WIRE, 4 W/WIRE JOINT, BLK

1 WIRE ASSY, W/2 PIN CONN, DLX

SERIAL NO.

FROM

NOTES


Suggested Spare Parts

PART NO.

86216180

86215800

86215320

86214850

86217230

86224970

86002010

86217120

86217200

86223390

86291860

86215670

86215710

86012470

86012550

86012570

86295190

86292780

86295150

86295180

86299810

86299830

PRV NO.

DESCRIPTION

-

-

-

-

-

-

141057 BRUSH SET, MTR, 54206/54216

11055 BELT, HTD, 15MM X 325, 65 TOOTH

11058

12544

BELT, HTD, 15MM X 300, 60 TOOTH

ASSY, BRUSH & HUB

38326 CORD HOOK, UPPER


14942

23729

BOOT, 3/8 CIRCUIT BREAKER

CORD SET, 10/3 X 40FT SITW

23738

67488

CORD SET, EURO 1.0MM X 40 BLK

RECTIFIER, 50A 600V BRIDGE

SWITCH, 125VAC SP NC NO-ROLLER



CAP, 2-1/4, POWER GRIP

-

-

JET, PROMAX, 11001

STRAP, CHEMICAL BOTTLES, DLX

ASM, BUTTON BLUE, W/BEZEL

SWITCH, TONELUCK

ASM, BUTTON, RED, W/BEZEL

ASM, BUTTON, GREEN, W/BEZEL

SWITCH, BLACK, ROCKER, DPST

COVER, SWITCH, PVC

SERIAL NO.

FROM

NOTES

120V ONLY

230V ONLY

120V ONLY

230V ONLY

DELUXE ONLY

DELUXE ONLY

DELUXE ONLY


REF.

NO.

1

MODEL: SERIAL #

IM: 10066360000690 - IMX: 10066400000781

Serial Numbers


Windsor IMXIE17 10066410 Operating instructions

Carpet Maintainer

OVERVIEW

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

SAVE THESE INSTRUCTIONS

Hazard Intensity Level

This Product Is For Commercial Use Only.

Electrical

Extension Cords

Grounding Instructions -

Safety Label Locations

Technical Specifications

How The Machines Work

Deluxe

Quick Dry Carpet Care System

Instructions

Deluxe

Machine Operation

Pre-Run Inspection

Starting Machine

Starting Machine - Deluxe

Transporting A Sprayer

Transporting Chemical - Deluxe

Shut-Down And Storage

Components

Brush Cleaning And Maintenance

Motor Replacement & Belt Tensioning

Machine Maintenance

Daily Maintenance

Periodic Maintenance

Annual Maintenance

Machine Troubleshooting

PARTS

Related manuals

Windsor

Carpet Maintainer IMIE17 10066550

Windsor

Carpet Maintainer IM 10066360

Peerless

76040SN

CARPET MAINTAINER

IMXIE17

Windsor

iCapsol Mini Deluxe

Kärcher

iCapsol™ BRS 43/500 C Deluxe

Kärcher

iCapsol™ BRS 43/500 C Deluxe

Newport

IMSLMC Cable Track Kit

Electro-Voice

M-12G