Sharp INSIGHTRANGEHOOD KB-0333K Operating instructions

 -//" Ê -/,1
/" ÊÉÊ"*,/" Ê 1
"
KB-0333K
&OLLOWEDBYINDICATINGCOLOR+BLACK7WHITE3STAINLESSSTEEL
INSIGHT RANGE HOOD
",Ê
1-/",Ê---/ Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° Ó
"
/Ê7, Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° n
" -1,Ê/Ê7,, /9Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° Î
-/Ê""Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° ™
*,"1
/Ê ",/" Ê
,Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° Î
" ‡1
/Ê/,-Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° ™
*",/ /Ê-/9Ê -/,1
/" -Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°° {
"*,/ Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°£ä
*,*,Ê""Ê"
/" Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° x
1-Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°£ä
*,*,Ê/Ê""Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° ÈʇÊn
Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°££
FOR CUSTOMER ASSISTANCE
To aid in reporting this range hood, please record below the model number and serial number located on the unit.
We also suggest you record all the information listed and retain for future reference.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
/
/
DEALER
TELEPHONE
SERVICER
TELEPHONE
TO PHONE:
DIAL
DIAL
TO WRITE:
1-800-BE-SHARP (237-4277) for:
SERVICE (for your nearest Sharp Authorized Servicer)
PARTS (for your authorized parts distributor)
1-800-642-2122 for: Charcoal Filters (model KBK-330)
Sharp Electronics Corporation
Customer Assistance Center
1300 Naperville Drive
Romeoville, IL 60446-1091
Please provide the following information when you write or call: model number, serial number, date of purchase, your
complete mailing address (including zip code), your daytime telephone number (including area code) and description of
the problem.
TO ACCESS INTERNET: www.sharpusa.com
2
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it
will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor
to any Product the exterior of which has been damaged or defaced, which has been subjected to misuse, abnormal service or
handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE
ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described
herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive
remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall
complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute
full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be
liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs
performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incident or
consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages,
so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Your product model number &
description
KB-0333K Home Use Range Hood. (Be sure to have this information available when
you need service for your Product.)
Warranty period for this product:
One (1) year parts and labor including in-home service.
Additional item(s) excluded from
warranty coverage (if any):
Light Bulbs
What to do to obtain service:
From a Sharp Authorized servicer located in the United States. Be sure to have Proof of
Purchase available. For in-home service, the servicer will come to the unit’s location.
If it is necessary to remove the unit for repair, the servicer will reinstall the unit at no
extra charge, provided it was installed according to Sharp’s Installation Instructions.
Where to obtain service:
From a Sharp Authorized Servicer located in the United States. To find the location
of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP
(1-800-237-4277).
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP or visit www.sharpusa.com.
SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR RANGE HOOD EVER REQUIRE WARRANTY
SERVICE.
PRODUCT INFORMATION CARD
The Product Information Card should be completed within ten days of purchase and returned. We will keep it on file and help
you access the information if needed. This will also enable us to contact you in the unlikely event that any adjustments or
modifications are ever required for your range hood.
3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING
TO REDUCE THE RISK OF INJURY TO PERSONS
IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:*
FOR DOMESTIC COOKING ONLY
WARNING
1. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact Sharp at
the address or telephone number listed on page 2 of this
manual.
2. NEVER PICK UP A FLAMING PAN — You may be
burned.
3. DO NOT USE WATER, including wet dishcloths or
towels - violent steam explosion will result.
2. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a
tag, to the service panel.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and
you already know how to operate it.
B. The fire is small and contained in the area where it
started.
3. Installation work and electrical wiring must be done by
a qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction
codes and standards.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
4. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American
Society of Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or
unbalanced impellers, keep drywall spray, construction
dust, etc. off power unit.
5. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
3. For best capture of cooking impurities, your range hood
should be mounted so that the top of the hood is 24-30”
above the cooking surface.
6. To reduce the risk of fire or electric shock, do not use this
range hood with an additional speed control device.
7. Ducted fans must always be vented to the outdoors.
4. Please read specification label on product for further
information and requirements.
9. Use with approved cord-connection kit only.
WARNING Halogen or incandescent bulbs may be hot!
Refer to bulb packaging for further information.
8. To reduce the risk of fire, use only metal ductwork.
10. This unit must be grounded.
Installer: Leave this manual with the homeowner.
TO REDUCE THE RISK OF A RANGE TOP GREASE
FIRE:
Homeowner: Operating instructions and Cleaning
information are on pages 10-11.
1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate
for the size of the surface element.
4
PREPARE HOOD LOCATION
1 Determine whether hood will discharge vertically (3 1⁄4”
x 10” or 7” round), horizontally (3 1⁄4” x 10” only) or
be non-ducted. For vertical or horizontal discharge, run
ductwork between the hood location and a roof cap or wall
cap. For best results, use a minimum number of transitions
and elbows.
ROOF CAP
31/4" X 10"
WOOD SHIMS
(Recessed-bottom
HORIZONTAL DUCTING
cabinets only)
CABINET FRONT
3/4"
1/8"
33/4"
CABINET
BOTTOM
31/4" X 10" or
7" ROUND DUCT
(For vertical
discharge)
HORIZONTAL DUCT
ACCESS HOLE
51/4"
1315/16" (30" hood)
HOOD
MOUNTING
SCREWS (4)
SOFFIT
51/4"
71/2"
1315/16" (30" hood)
CENTER
LINE
ELECTRICAL
ACCESS HOLE
(In wall)
HOUSE WIRING
(Top or back of hood)
CABINET
7" ROUND
VERTICAL DUCTING
WALL CAP
HOOD
24" - 30" ABOVE
COOKING SURFACE
31/4" X 10" DUCT
(For horizontal discharge)
2 Use diagrams for proper placement of ductwork and
electrical cutout in cabinet or wall. For a non-ducted
installation, DO NOT cut a duct access hole.
31/4" X 10"
VERTICAL DUCTING
HOOD MOUNTING SCREWS (4)
1315/16" (30" hood)
(Recessed-bottom
(In cabinet bottom)
1315/16" (30" hood)
CABINET FRONT
71/2"
CABINET BOTTOM
51/4"
51/4"
5"
VERTICAL DUCT
ACCESS HOLE
NON-DUCTED
2"
11/4"
WOOD SHIMS
(Recessed-bottom
cabinets only)
101/2"
11/2"
CENTER
LINE
ELECTRICAL
ACCESS HOLE
(In cabinet bottom)
(Recessed-bottom
(In cabinet bottom)
3 Run house wiring between service panel and hood location.
5
PREPARE THE HOOD
1 Remove 7” Round
NON-DUCTED INSTALLATION - Skip to page 8.
Duct Plate from top
of hood. Set duct
plate aside - with
mounting screws.
The following Steps (6 thru 14) are for DUCTED
INSTALLATION ONLY.
6 R e m ove L i g h t
Panel - held in
place with (5) #8
screws. Disconnect
l ig ht a s s e m bly
wire harness
(white connector).
2 Remove
tape
holding Filters in
place. Pull down
on filter tabs or
finger holes and
lift filters out. Set
filters aside.
7 Remove Air Chute
- held in place with
one (1) screw.
Note: Be careful
not to disconnect
any wires.
3 Remove Teflon ®-
Coat ed Bottom
Cover from hood.
Set cover a nd
mounting screws
aside.
Teflon® is a registered
trademark of DuPont.
4 Remove Damper/
8
Remove Baffle from air chute.
9
Rotate baff le.
Reinsert baffle
into air chute
(as shown) so
that baffle Tabs
fit all the way
into Slots in air
chute. An audible
“click” will be
heard when fully
installed. This
will close off the
air flow through
the non-ducted
slots on top of
hood.
TEFLON®-COATED BOTTOM COVER
(Held in place with 2 screws)
Duct Connector
f rom i nside t he
hood. Set connector
aside - with mounting
screws and parts
bag.
DAMPER/ DUCT CONNECTOR
5 Remove either top
o r b a ck w i r i ng
knockout and install
approved Electrical
Cable Clamp.
ELECTRICAL CABLE CLAMP
6
PREPARE THE HOOD
13 3 1⁄4” x 10” Ducted Discharge Only: Remove tape from
10 Re-install air chute and screw, re-connect wire harness
damper flap and attach Damper/Duct Connector over
knockout opening with screws removed in Step 4 under
“PREPARE THE HOOD”. Make sure damper Pivot is
nearest to top/back edge of hood.
and replace light panel.
Note: Be careful not to trap wires between Support Fin
and light panel.
11 Remove appropriate Duct Knockout(s) from top or back
of hood.
14 7” Round Ducted Discharge Only: Re-install 7” Round
Duct Plate removed in Step #1 under “PREPARE
THE HOOD”. Install a 7” Round Damper (purchase
separately). Damper flap must open freely in direction
of airflow (away from range hood).
12 Horizontal Discharge Only: Remove the Plate in front of
the horizontal discharge knockout. Cut the ties, lift plate
out, and discard plate. DO NOT REMOVE the Metal
Strip held in place with two screws.
Note: To accommodate off-center ductwork, the Damper/
Duct Connector can be installed up to 1-inch on either side
of hood center or the 7” Round Duct Plate can be installed
up to 1⁄2” on either side of hood center. In extreme off-center
installations, one end of the duct connector may need to be
trimmed to clear the electrical cable clamp.
7
PREPARE THE HOOD
5. Check that wheel is properly positioned as shown.
Non-Ducted Installations Only:
Press Sections into place if necessary. Make sure wheel
turns freely.
Requires a Performance Ring to be attached to the blower
wheel. The Performance Ring is packed behind the Teflon®Coated Bottom Cover.
Note: For information on non-ducted filters, see page 9.
To install ring:
1. Remove Retaining Ring using a flat blade screwdriver.
Set aside for later. Remove the Blower Wheel by rocking
it side to side and applying a slight force to pull wheel
from motor. Turn the Blower Wheel over.
RETAINING RING
BLOWER
WHEEL
SMALL DIAMETER
END
TAB
2. Slide the Performance Ring onto the Small Diameter
End of the blower wheel and down to the Stop Edge of
the wheel.
3. Reassemble wheel to motor. Make sure Tab on wheel
SECTIONS
fits into one of the Motor Slots.
STOP
EDGE
4. Push wheel down until it is locked in place. Replace
Retaining Ring from Step 1. Be sure it is within the
upper and lower tabs.
MOTOR SLOTS
PERFORMANCE RING
CONNECT WIRING
2 Connect house black to hood black wire, house white to
WARNING To reduce the risk of electric shock, make
sure power is switched off at the service panel. Lock or
tag service panel to prevent power from being switched
on accidentally.
hood white wire and house ground under Green Ground
Screw. Securely tighten cable clamp onto house wiring.
1 Connect House Wiring (120 VAC) to hood. Use a piece
of cardboard to protect the cooktop, if necessary.
8
INSTALL HOOD
1 Hang hood from (4) mounting screws. Slide hood towards
4 Install (2) PAR20, 50 W Maximum Halogen Bulbs or
(2) R16, 40 W Maximum Incandescent Bulbs. Purchase
bulbs separately.
wall until mounting screws are engaged in narrow end of
(4) keyholes. Tighten mounting screws securely. A long
screwdriver works best.
5 Replace filters, turn on power at service panel and test for
2 Replace bottom cover.
proper operation.
3 Connect ductwork to hood. Use duct tape to make joints
secure and air tight.
NON-DUCTED FILTERS
If hood is to be installed Non-Ducted:
• Attach charcoal filters to the aluminum mesh filters. Be
sure that the sides with the blue and yellow stripes are
facing down (toward the range top).
• Purchase a set of (2) charcoal filters, model KBK-330,
from your local distributor, retailer or from Sharp (see
page 2).
9
OPERATING
3
1
2
1 FAN There are four fan speeds from low (1) to high (4).
4
HEAT SENSOR
Push any button to select one of the four fan speeds. Press
another button to change fan speed. Push the same button
to turn the fan off. A light above each fan button indicates
the fan speed.
Your Sharp Insight Range Hood is equipped with an advanced
Heat Sensor.
The Sensor monitors the temperature and automatically
adjusts the fan to the appropriate setting.
2 LIGHT Press the ON/OFF button and lights will come on
• If the fan is on, the Sensor will increase the fan setting
when the temperature is elevated. If the temperature
continues to rise, the Sensor will continue to increase the
fan setting until the temperature is stabilized or reduced.
The flashing light above the fan button shows the Sensor
fan setting. Once the temperature has been reduced, the
Sensor will change the fan to the original setting.
at their previous light level. Press the button again to turn
lights off. To increase the light level, press
button.
To reduce light level, press the
button. There are
three light levels.
3 DELAY OFF While the fan is running, press the “DELAY
OFF” button to allow the fan to run for 10 minutes and
then turn off automatically.
• If the fan is off, the Sensor will automatically turn the
fan on at its highest speed when the temperature is above
normal. When this occurs, the light above fan button 4 will
flash on and off. After the temperature has been reduced
to normal, the fan will change to the setting prior to the
Sensor coming on.
4 FILTER CHANGE INDICATOR The light above
“CLEAN FILTER” will come on when it is time to clean the
grease filters or check non-ducted filters. After replacing
the cleaned filters (or installing new ones), press the
“CLEAN FILTER” button to turn off the indicator light.
FUSE
To replace the fuse:
The hood control contains a fuse to protect it from power
surges. If the fuse has opened (blown), the green fan-level
indicators will operate properly when the fan buttons/switches
are pressed, but the fan and lights will not turn on.
1. Disconnect power at service entrance.
2. Remove filters, bottom panel, light wire harness and air
chute.
The fuse is a 5 x 20mm, 10 Amp, Fast-Acting, 125V (min.).
Common manufacturer and part numbers are: Littlefuse,
217010; Bussmann, GMA10A; Wickmann, 1942100. Radio
Shack, Digikey (1-800-344-4539), and most electronic supply
stores have them in stock.
3. Remove and inspect fuse. If it is not open (blown),
additional diagnostics need to be done.
4. Install new fuse.
5. Re-assemble air chute, light wire harness, bottom panel
and filters.
6. Turn on power and check hood/control operation.
10
CLEANING
To clean hood: Remove filters. Use a damp cloth and
To reduce the risk of electric shock, disconnect from power supply before cleaning.
WARNING
a mild detergent to wipe all grease-laden surfaces. Do not
use abrasive cloth, steel wool pads or scouring powder on
the Teflon®-coated bottom cover or on any painted surface.
Use care when cleaning blower wheel - it must not become
bent or misaligned. DO NOT ALLOW WATER TO ENTER
MOTOR. Make sure all surfaces are completely dry before
re-installing filters and restoring power. Motor is permanently
lubricated. Do not oil or disassemble motor.
Aluminum mesh filters: Clean frequently using hot
water and a mild detergent. Filters are dishwasher safe.
Charcoal filters (additional filters for nonducted installations): Clean filter surfaces frequently
with a damp cloth and a mild detergent. DO NOT immerse
filters in water or put in dishwasher. The special “Clean
Sense” feature indicates when the filter is to be replaced.
The blue and yellow stripes will blend to green when it is
time to change the filter. The “Clean Sense” feature works
best when facing toward the cooking surface.
Teflon® is a registered trademark of DuPont.
11
–
This symbol on the nameplate means the product is listed by Underwriters Laboratories, Inc.
SHARP ELECTRONICS CORPORATION • Sharp Plaza, Mahwah, New Jersey 07430-2135
PRINTED IN USA
626 9 9 5B