HP DL385 - ProLiant - G5 User guide

HP ProLiant DL385 Generation 5 Server
User Guide
Part Number 457041-001
November 2007 (First Edition)
© Copyright 2007 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP
shall not be liable for technical or editorial errors or omissions contained herein.
Microsoft, Windows, and Windows NT are U.S. registered trademarks of Microsoft Corporation. Windows Server 2003 is a trademark of
Microsoft Corporation.
Audience assumptions
This document is for the person who installs, administers, and troubleshoots servers and storage systems.
HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards
in products with hazardous energy levels.
Contents
Component identification ............................................................................................................... 7
Front panel components ............................................................................................................................. 7
Front panel LEDs and buttons ...................................................................................................................... 7
Systems Insight Display LEDs ....................................................................................................................... 9
Rear panel components............................................................................................................................ 10
PCI expansion slot definitions .......................................................................................................... 10
PCI riser board expansion slot definitions ......................................................................................... 11
Rear panel LEDs and buttons..................................................................................................................... 11
System board ......................................................................................................................................... 12
System board components .............................................................................................................. 12
DIMM slots ................................................................................................................................... 13
System maintenance switch............................................................................................................. 13
NMI functionality........................................................................................................................... 14
Systems Insight Display LEDs and internal health LED combinations ................................................................ 14
Device numbers ...................................................................................................................................... 16
SAS and SATA hard drive LEDs................................................................................................................. 16
SAS and SATA hard drive LED combinations .............................................................................................. 17
PCI riser cage LED ................................................................................................................................... 17
Battery pack LEDs.................................................................................................................................... 18
Hot-plug fans .......................................................................................................................................... 20
Fan board components ............................................................................................................................ 20
Operations................................................................................................................................. 21
Power up the server ................................................................................................................................. 21
Power down the server............................................................................................................................. 21
Extend the server from the rack ................................................................................................................. 21
Remove the access panel.......................................................................................................................... 22
Install the access panel............................................................................................................................. 23
Remove the air baffle ............................................................................................................................... 23
Install the air baffle .................................................................................................................................. 24
Remove the PCI riser cage ........................................................................................................................ 25
Install the PCI riser cage ........................................................................................................................... 25
Access the product rear panel................................................................................................................... 27
Cable management arm with left-hand swing .................................................................................... 27
Cable management arm with right-hand swing.................................................................................. 27
Hot-plug fan operation ............................................................................................................................. 28
Setup......................................................................................................................................... 29
Optional installation services .................................................................................................................... 29
Rack planning resources........................................................................................................................... 29
Optimum environment.............................................................................................................................. 30
Space and airflow requirements ...................................................................................................... 30
Temperature requirements............................................................................................................... 30
Power requirements ....................................................................................................................... 31
Electrical grounding requirements .................................................................................................... 31
Rack warnings ........................................................................................................................................ 32
Identifying the contents of the server shipping carton.................................................................................... 32
Contents
3
Installing hardware options....................................................................................................................... 33
Installing the server into the rack................................................................................................................ 33
Powering up and configuring the server ..................................................................................................... 35
Installing the operating system................................................................................................................... 35
Registering the server............................................................................................................................... 36
Hardware options installation....................................................................................................... 37
Introduction ............................................................................................................................................ 37
Processor option...................................................................................................................................... 37
Memory options ...................................................................................................................................... 42
Advanced ECC memory ................................................................................................................. 43
DIMM installation guidelines ........................................................................................................... 43
Installing DIMMs ........................................................................................................................... 43
Hot-plug SAS hard drive options ............................................................................................................... 44
Installing a hot-plug SAS hard drive ................................................................................................. 45
Removing a hot-plug SAS hard drive ................................................................................................ 46
Media drive option.................................................................................................................................. 47
Redundant hot-plug AC power supply option .............................................................................................. 47
DC power supply option .......................................................................................................................... 48
Expansion board options.......................................................................................................................... 51
Installing an expansion board (slot 2)............................................................................................... 51
Removing an expansion slot cover (slot 3, 4, or 5)............................................................................. 51
Installing an expansion board (slot 3, 4, or 5)................................................................................... 52
PCI riser board option.............................................................................................................................. 53
Cabling ..................................................................................................................................... 55
SAS hard drive cabling ............................................................................................................................ 55
PCI SAS cabling to an HP Smart Array P400i Controller..................................................................... 55
PCI SAS cabling to an optional expansion board controller ................................................................ 55
Fan board cabling................................................................................................................................... 56
Battery cabling for BBWC ........................................................................................................................ 56
Systems Insight Display cabling ................................................................................................................. 57
Hard drive backplane power cabling......................................................................................................... 57
Media drive bay cabling.......................................................................................................................... 58
PCIe x16 riser board power cabling .......................................................................................................... 58
Software and configuration utilities ............................................................................................... 59
Configuration tools .................................................................................................................................. 59
SmartStart software........................................................................................................................ 59
HP ROM-Based Setup Utility............................................................................................................ 60
Array Configuration Utility .............................................................................................................. 61
Option ROM Configuration for Arrays ............................................................................................. 62
HP ProLiant Essentials Rapid Deployment Pack .................................................................................. 62
Re-entering the server serial number and product ID ........................................................................... 62
Management tools................................................................................................................................... 63
Automatic Server Recovery ............................................................................................................. 63
ROMPaq utility.............................................................................................................................. 63
System Online ROM flash component utility ...................................................................................... 63
Integrated Lights-Out 2 technology ................................................................................................... 64
Erase Utility .................................................................................................................................. 64
StorageWorks library and tape tools................................................................................................ 64
HP Systems Insight Manager ........................................................................................................... 65
Management Agents...................................................................................................................... 65
Redundant ROM support ................................................................................................................ 65
Contents
4
USB support.................................................................................................................................. 66
Diagnostic tools ...................................................................................................................................... 67
HP Insight Diagnostics .................................................................................................................... 67
HP Insight Diagnostics survey functionality ........................................................................................ 67
Integrated Management Log ........................................................................................................... 68
Array Diagnostic Utility .................................................................................................................. 68
Remote support and analysis tools ............................................................................................................. 68
HP Instant Support Enterprise Edition................................................................................................ 68
Web-Based Enterprise Service......................................................................................................... 68
Open Services Event Manager ........................................................................................................ 69
Keeping the system current ....................................................................................................................... 69
Drivers ......................................................................................................................................... 69
ProLiant Support Packs ................................................................................................................... 69
Operating system version support .................................................................................................... 69
Change control and proactive notification ........................................................................................ 69
Care Pack .................................................................................................................................... 70
Troubleshooting .......................................................................................................................... 71
Troubleshooting resources ........................................................................................................................ 71
Pre-diagnostic steps ................................................................................................................................. 71
Important safety information............................................................................................................ 71
Symptom information ..................................................................................................................... 73
Prepare the server for diagnosis ...................................................................................................... 74
Loose connections ................................................................................................................................... 74
Service notifications................................................................................................................................. 75
Troubleshooting flowcharts ....................................................................................................................... 75
Start diagnosis flowchart ................................................................................................................ 75
General diagnosis flowchart ........................................................................................................... 76
Server power-on problems flowchart ................................................................................................ 78
POST problems flowchart ............................................................................................................... 81
OS boot problems flowchart ........................................................................................................... 82
Server fault indications flowchart ..................................................................................................... 84
POST error messages and beep codes ....................................................................................................... 86
Battery replacement .................................................................................................................... 87
Regulatory compliance notices ..................................................................................................... 88
Federal Communications Commission notice............................................................................................... 88
FCC rating label............................................................................................................................ 88
Class A equipment......................................................................................................................... 88
Class B equipment ......................................................................................................................... 88
Declaration of conformity for products marked with the FCC logo, United States only....................................... 89
Modifications.......................................................................................................................................... 89
Cables ................................................................................................................................................... 89
Canadian notice (Avis Canadien).............................................................................................................. 89
European Union regulatory notice ............................................................................................................. 90
Disposal of waste equipment by users in private households in the European Union ......................................... 90
Japanese notice ...................................................................................................................................... 91
BSMI notice ............................................................................................................................................ 91
Korean notice ......................................................................................................................................... 91
Laser compliance .................................................................................................................................... 92
Battery replacement notice........................................................................................................................ 92
Taiwan battery recycling notice................................................................................................................. 92
Power cord statement for Japan................................................................................................................. 93
Contents
5
Electrostatic discharge ................................................................................................................. 94
Preventing electrostatic discharge .............................................................................................................. 94
Grounding methods to prevent electrostatic discharge .................................................................................. 94
Specifications ............................................................................................................................. 95
Environmental specifications ..................................................................................................................... 95
Server specifications ................................................................................................................................ 95
Technical support........................................................................................................................ 97
Before you contact HP.............................................................................................................................. 97
HP contact information ............................................................................................................................. 97
Customer Self Repair ............................................................................................................................... 97
Acronyms and abbreviations...................................................................................................... 105
Index....................................................................................................................................... 109
Contents
6
Component identification
Front panel components
Item
Description
1
Media drive bay (IDE/diskette multibay)
2
Video connector
3
USB connectors (2)
4
Systems Insight Display
5
Hard drive bays
6
Quick release levers (2)
Front panel LEDs and buttons
Component identification 7
Item
Description
Status
1
UID LED button
Blue = Activated
Flashing = System being remotely managed
Off = Deactivated
2
Internal health LED
Green = Normal
Amber = System degraded. To identify component in degraded
state, see Systems Insight Display LEDs (on page 9).
Red = System critical. To identify component in critical state, see
Systems Insight Display LEDs (on page 9).
3
External health LED (power
supply)
Green = Normal
Amber = Power redundancy failure. To identify component in
degraded state, see Systems Insight Display LEDs (on page 9).
Red = Critical power supply failure. To identify component in
critical state, see Systems Insight Display LEDs (on page 9).
4
NIC 1 link/activity LED
Green = Network link
Flashing = Network link and activity
Off = No link to network. If power is off, view the rear panel
RJ­45 LEDs for status.
5
NIC 2 link/activity LED
Green = Network link
Flashing = Network link and activity
Off = No link to network. If power is off, view the rear panel
RJ­45 LEDs for status.
6
Power On/Standby
button/system power LED
Green = System on
Amber = System shut down, but power still applied
Off = Power cord not attached or power supply failure
Component identification 8
Systems Insight Display LEDs
Status
Amber= Failure
Off = Normal
IMPORTANT: If more than one DIMM slot LED is illuminated, further troubleshooting is
required. Test each bank of DIMMs by removing all other DIMMs. Isolate the failed DIMM by
replacing each DIMM in a bank with a known working DIMM.
Component identification 9
Rear panel components
Item
Description
Color
1
Expansion slot 1
—
2
Expansion slot 2
—
3
Expansion slot 3
—
4
Expansion slot 4
—
5
Expansion slot 5
—
6
T-10/T-15 Torx screwdriver
—
7
External option blank
—
8
NIC 2 connector
—
9
NIC 1 connector
—
10
Power supply bay 2
—
11
Power cord connector
Black
12
Power supply bay 1 (populated)
—
13
iLO 2 connector
—
14
Video connector
Blue
15
USB connectors (2)
Black
16
Serial connector
—
17
Mouse connector
Green
18
Keyboard connector
Purple
PCI expansion slot definitions
Slot
Type and speed
1
PCIe x8
2
PCIe x8
Component identification 10
All slots are non-hot-plug.
PCI riser board expansion slot definitions
Slot
PCIe riser board
Mixed PCIe/PCI-X riser board
PCIe x16 riser board
5
x8
64-bit/133-MHz
—
4
x8
64-bit/133-MHz
x16
3
x4
x8
x4
All slots are non-hot-plug.
Rear panel LEDs and buttons
Item
Description
Status
1
Power supply LED
Green = Normal
Off = System is off or power supply has failed
2
UID LED button
Blue = Activated
Flashing = System being remotely managed
Off = Deactivated
3
NIC/iLO 2 activity Green = Network activity
LED
Flashing = Network activity
Off = No network activity
4
NIC/iLO 2 link
LED
Green = Network link
Off = No network link
Component identification 11
System board
System board components
Item
Description
1
Fan board connector
2
DIMM slots (1-4)
3
Power supply backplane connector
4
PCIe slot 1
5
PCIe slot 2
6
System battery
7
System maintenance switch
8
Diagnostic LEDs
9
NMI jumper
10
Internal USB connector*
11
PCI riser cage connector
12
Fan 2 connector
13
Fan 1 connector
14
DIMM slots (5-8)
15
PPM 2 (embedded)
16
Multibay interface connector
17
Processor socket 2
18
Processor socket 1
19
PPM 1 (embedded)
* The lower USB connector is unavailable.
Component identification 12
DIMM slots
Item
Description
1
DIMM slot 1A
2
DIMM slot 2A
3
DIMM slot 3B
4
DIMM slot 4B
5
DIMM slot 5C
6
DIMM slot 6C
7
DIMM slot 7D
8
DIMM slot 8D
System maintenance switch
Position
Default
Function
S1
Off
Off = iLO 2 security is enabled.
On = iLO 2 security is disabled.
S2
Off
Off = System configuration can be modified.
On = System configuration is locked and cannot be modified.
S3
Off
Reserved
S4
Off
Reserved
Component identification 13
Position
Default
Function
S5
Off
Off = Power-on password is enabled.
On = Power-on password is disabled.
S6
Off
Off = Normal
On = ROM treats system configuration as invalid.
S7
Off
Reserved
S8
Off
Reserved
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase
all system configuration settings from both CMOS and NVRAM.
CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to
properly configure the server or data loss could occur.
NMI functionality
An NMI crash dump enables administrators to create crash dump files when a system is hung and not
responding to traditional debug mechanisms.
Crash dump log analysis is an essential part of diagnosing reliability problems, such as hangs in
operating systems, device drivers, and applications. Many crashes freeze a system, and the only
available action for administrators is to cycle the system power. Resetting the system erases any
information that could support problem analysis, but the NMI feature preserves that information by
performing a memory dump before a hard reset.
To force the OS to invoke the NMI handler and generate a crash dump log, the administrator can do any
of the following:
•
Short the NMI jumper pins
•
Press the NMI switch
•
Use the iLO Virtual NMI feature
For additional information, see the whitepaper on the HP website
(http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00797875/c00797875.pdf).
Systems Insight Display LEDs and internal health LED
combinations
When the internal health LED on the front panel illuminates either amber or red, the server is experiencing
a health event. Combinations of illuminated system LEDs and the internal health LED indicate system
status.
Component identification 14
Systems Insight Display
LED and color
Internal Health LED color
Status
Processor failure, socket X
(amber)
Red
One or more of the following conditions may
exist:
PPM failure (amber)
•
Processor in socket X has failed.
•
Processor X is not installed in the socket.
•
Processor X is unsupported.
•
ROM detects a failed processor during
POST.
Amber
Processor in socket X is in a pre-failure
condition.
Red
One or more of the following conditions may
exist:
•
PPM for processor 2 has failed.
•
PPM is not installed, but processor 2 is
installed.
I-PPM failure (amber)
Red
Embedded I-PPM for processor 1 has failed.
DIMM failure, slot X (amber)
Red
One or more of the following conditions may
exist:
Amber
•
DIMM in slot X has failed.
•
Memory group is populated with different
DIMM types (all DIMMs are mismatched).
One or more of the following conditions may
exist:
•
DIMM in slot X is in a pre-failure condition.
•
Memory group is populated with different
DIMM types (at least one DIMM is good).
DIMM failure, all slots in one Red
bank (amber)
One or more DIMMs has failed. Test each
bank of DIMMs by removing all other DIMMs.
Isolate the failed DIMM by replacing each
DIMM in a bank with a known working
DIMM.
DIMM failure, all slots in all
banks (amber)
Red
One or more DIMMs has failed. Test each
bank of DIMMs by removing all other DIMMs.
Isolate the failed DIMM by replacing each
DIMM in a bank with a known working
DIMM.
Overtemperature (amber)
Red
The server has detected a hardware critical
temperature level.
Fan (amber)
Amber
One fan has failed in redundant mode.
Red
One or more of the following conditions may
exist:
•
One fan has failed in non-redundant mode
•
The minimum fan requirements are not
being met. Two or more fans have failed
or are missing.
Component identification 15
Systems Insight Display
LED and color
Internal Health LED color
Status
Power supply X (amber)
Red
Power supply X has failed.
PCI riser cage interlock
(amber)
—
PCI riser cage is unseated.
Device numbers
SAS and SATA hard drive LEDs
Item
Description
1
Fault/UID LED (amber/blue)
2
Online LED (green)
Component identification 16
SAS and SATA hard drive LED combinations
Online/activity
LED (green)
Fault/UID LED
(amber/blue)
On, off, or
flashing
Alternating amber and The drive has failed, or a predictive failure alert has been
blue
received for this drive; it also has been selected by a
management application.
On, off, or
flashing
Steadily blue
The drive is operating normally, and it has been selected by a
management application.
On
Amber, flashing
regularly (1 Hz)
A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.
Off
The drive is online, but it is not active currently.
On
Flashing regularly Amber, flashing
(1 Hz)
regularly (1 Hz)
Interpretation
Do not remove the drive. Removing a drive may terminate the
current operation and cause data loss.
The drive is part of an array that is undergoing capacity
expansion or stripe migration, but a predictive failure alert has
been received for this drive. To minimize the risk of data loss,
do not replace the drive until the expansion or migration is
complete.
Flashing regularly Off
(1 Hz)
Do not remove the drive. Removing a drive may terminate the
current operation and cause data loss.
The drive is rebuilding, or it is part of an array that is
undergoing capacity expansion or stripe migration.
Flashing
irregularly
Amber, flashing
regularly (1 Hz)
The drive is active, but a predictive failure alert has been
received for this drive. Replace the drive as soon as possible.
Flashing
irregularly
Off
The drive is active, and it is operating normally.
Off
Steadily amber
A critical fault condition has been identified for this drive, and
the controller has placed it offline. Replace the drive as soon as
possible.
Off
Amber, flashing
regularly (1 Hz)
A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.
Off
Off
The drive is offline, a spare, or not configured as part of an
array.
PCI riser cage LED
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
Component identification 17
Status
On = AC power connected
Off = AC power disconnected
Battery pack LEDs
Item ID
Color
Description
1
Green
System Power LED. This LED glows steadily when the
system is powered up and 12 V system power is
available. This power supply is used to maintain the
battery charge and provide supplementary power to the
cache microcontroller.
Component identification 18
Item ID
Color
Description
2
Green
Auxiliary Power LED. This LED glows steadily when 3.3V
auxiliary voltage is detected. The auxiliary voltage is used
to preserve BBWC data and is available any time that the
system power cords are connected to a power supply.
3
Amber
Battery Health LED. To interpret the illumination patterns of
this LED, see the following table.
4
Green
BBWC Status LED. To interpret the illumination patterns of
this LED, see the following table.
LED3 pattern
LED4 pattern
Interpretation
—
One blink every
two seconds
The system is powered down, and the cache contains data that has
not yet been written to the drives. Restore system power as soon as
possible to prevent data loss.
Data preservation time is extended any time that 3.3 V auxiliary
power is available, as indicated by LED 2. In the absence of
auxiliary power, battery power alone preserves the data. A fullycharged battery can normally preserve data for at least two days.
The battery lifetime also depends on the cache module size. For
further information, refer to the controller QuickSpecs on the HP
website (http://www.hp.com).
—
Double blink,
then pause
The cache microcontroller is waiting for the host controller to
communicate.
—
One blink per
second
The battery pack is below the minimum charge level and is being
charged. Features that require a battery (such as write cache,
capacity expansion, stripe size migration, and RAID migration) are
temporarily unavailable until charging is complete. The recharge
process takes between 15 minutes and two hours, depending on the
initial capacity of the battery.
—
Steady glow
The battery pack is fully charged, and posted write data is stored in
the cache.
—
Off
The battery pack is fully charged, and there is no posted write data
in the cache.
One blink per
second
One blink per
second
An alternating green and amber blink pattern indicates that the
cache microcontroller is executing from within its boot loader and
receiving new flash code from the host controller.
Steady glow
—
There is a short circuit across the battery terminals or within the
battery pack. BBWC features are disabled until the battery pack is
replaced. The life expectancy of a battery pack is typically more
than three years.
One blink per
second
—
There is an open circuit across the battery terminals or within the
battery pack. BBWC features are disabled until the battery pack is
replaced. The life expectancy of a battery pack is typically more
than three years.
Component identification 19
Hot-plug fans
The fan configuration operates in redundant mode only when all six fans are installed.
Fan board components
Item
Description
1
Fan connectors
2
Systems Insight Display connector
3
Power On/Standby button/system power LED
4
UID LED button
5
USB connectors (2)
6
Video connector
7
Fan board system connector
Component identification 20
Operations
Power up the server
To power up the server, press the Power On/Standby button.
Power down the server
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some
internal circuitry remain active until AC power is removed.
IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server.
1.
Back up the server data.
2.
Shut down the operating system as directed by the operating system documentation.
NOTE: If the operating system automatically places the server in Standby mode, omit the next
step.
3.
Press the Power On/Standby button to place the server in Standby mode. When the server activates
Standby power mode, the system power LED changes to amber.
IMPORTANT: Pressing the UID button illuminates the blue UID LEDs on the front and rear
panels. In a rack environment, this feature facilitates locating a server when moving between
the front and rear of the rack.
4.
Disconnect the power cords.
The system is now without power.
Extend the server from the rack
1.
Pull down the quick release levers on each side of the server.
2.
Extend the server until the server rail-release latches engage.
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack
is adequately stabilized before extending a component from the rack.
Operations 21
3.
After performing the installation or maintenance procedure, slide the server back into the rack:
a. Press the server rail-release latches and slide the server fully into rack.
WARNING: To reduce the risk of personal injury, be careful when pressing the server railrelease latches and sliding the server into the rack. The sliding rails could pinch your fingers.
b. Slide the server fully into the rack.
Remove the access panel
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
Operations 22
To remove the component:
1.
Power down the server if performing a non-hot-plug installation or maintenance procedure ("Power
down the server" on page 21).
2.
Extend the server from the rack (on page 21).
3.
Use the T-15 Torx screwdriver attached to the rear of the server to loosen the security screw on the
hood latch.
4.
Lift up on the hood latch handle and remove the access panel.
Install the access panel
1.
Place the access panel on top of the server with the hood latch open. Allow the panel to extend past
the rear of the server approximately 1.25 cm (0.5 in).
2.
Push down on the hood latch. The access panel slides to a closed position.
3.
Use the T-15 Torx screwdriver attached to the rear of the server to tighten the security screw on the
hood latch.
Remove the air baffle
IMPORTANT: To maintain proper airflow and prevent thermal damage, always install the air
baffle.
1.
Power down the server (on page 21).
2.
Extend or remove the server from the rack ("Extend the server from the rack" on page 21).
3.
Remove the access panel (on page 22).
CAUTION: Disconnecting the battery module cable will cause any unsaved data in the cache
module to be lost.
4.
Disconnect the cable, and then remove the BBWC battery pack.
Operations 23
5.
Remove the air baffle.
Install the air baffle
IMPORTANT: To maintain proper airflow and prevent thermal damage, always install the air
baffle.
Depending on the fan configuration, the air baffle is different. Use the following procedure for either
configuration.
1.
Install the air baffle.
2.
Install the BBWC battery pack.
3.
Install the access panel (on page 23).
4.
Install the server into the rack.
5.
Power up the server (on page 21).
Operations 24
Remove the PCI riser cage
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all PCI slots have either an expansion slot cover or an expansion board installed.
1.
Power down the server (on page 21).
2.
Extend the server from the rack (on page 21).
3.
Remove the access panel (on page 22).
4.
Disconnect any internal or external cables connected to any existing expansion boards.
5.
Press the blue buttons to release the black knobs.
6.
Turn the black knobs counter-clockwise.
7.
Remove the PCI riser cage.
Install the PCI riser cage
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
Operations 25
1.
Align the PCI riser cage with the chassis and slide it into place.
2.
Tighten the thumbscrews to secure the PCI riser cage:
a. Press down the black knob while turning clockwise, until fully tightened.
b. While holding the black knob and pressing down, press and release the blue button to lower the
black knob to the locked position.
3.
Connect any required internal cables to the expansion board. Refer to the documentation that ships
with the expansion board.
4.
Install the access panel (on page 23).
5.
Install the server into the rack.
6.
Connect any required external cables to the expansion board. Refer to the documentation that ships
with the expansion board.
7.
Power up the server (on page 21).
Operations 26
Access the product rear panel
Cable management arm with left-hand swing
To access the server rear panel, open the cable management arm.
Cable management arm with right-hand swing
NOTE: To access some components, you may need to remove the cable management arm.
To access the product rear panel components, open the cable management arm:
1.
Power down the server (on page 21).
2.
Swing open the cable management arm.
3.
Remove the cables from the cable trough.
Operations 27
4.
Remove the cable management arm.
Hot-plug fan operation
The server supports variable fan speeds. The fans operate at minimum speed until a temperature change
requires a fan speed increase to cool the server.
The server shuts down in the following temperature-related scenarios:
•
At POST:
o
The BIOS suspends the server for 5 minutes if it detects a cautionary temperature level. If the
cautionary temperature level is still detected after 5 minutes, the BIOS performs an orderly
shutdown and enters Standby mode.
o
The BIOS performs an orderly shutdown if two or more fans have failed.
o
The server performs an immediate shutdown if it detects a critical temperature level.
IMPORTANT: An immediate shutdown is a hardware-controlled function and it overrides any
firmware or software actions.
•
In the operating system:
o
The Health Driver performs an orderly shutdown if it detects a cautionary temperature level. If the
server detects a critical temperature level before the orderly shutdown occurs, the server performs
an immediate shutdown. Additionally, the Health Driver performs an orderly shutdown if more
than one fan is failed or removed.
o
When Thermal Shutdown is disabled in RBSU, the server performs an immediate shutdown if it
detects a critical temperature level.
IMPORTANT: An immediate shutdown is a hardware-controlled function and it overrides any
firmware or software actions.
Operations 28
Setup
Optional installation services
Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and
running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you
integrate both hardware and software support into a single package. A number of service level options
are available to meet your needs.
HP Care Pack Services offer upgraded service levels to expand your standard product warranty with easyto-buy, easy-to-use support packages that help you make the most of your server investments. Some of the
Care Pack services are:
•
•
•
•
Hardware support
o
6-Hour Call-to-Repair
o
4-Hour 24x7 Same Day
o
4-Hour Same Business Day
Software support
o
Microsoft®
o
Linux
o
HP ProLiant Essentials (HP SIM and RDP)
o
VMWare
Integrated hardware and software support
o
Critical Service
o
Proactive 24
o
Support Plus
o
Support Plus 24
Startup and implementation services for both hardware and software
For more information on Care Packs, refer to the HP website
(http://www.hp.com/hps/carepack/servers/cp_proliant.html).
Rack planning resources
The rack resource kit ships with all HP branded or Compaq branded 9000, 10000, and H9 series racks.
For more information on the content of each resource, refer to the rack resource kit documentation.
If you intend to deploy and configure multiple servers in a single rack, refer to the white paper on highdensity deployment at the HP website (http://www.hp.com/products/servers/platforms).
Setup
29
Optimum environment
When installing the server in a rack, select a location that meets the environmental standards described in
this section.
Space and airflow requirements
To allow for servicing and adequate airflow, observe the following space and airflow requirements when
deciding where to install a rack:
•
Leave a minimum clearance of 63.5 cm (25 in) in front of the rack.
•
Leave a minimum clearance of 76.2 cm (30 in) behind the rack.
•
Leave a minimum clearance of 121.9 cm (48 in) from the back of the rack to the back of another
rack or row of racks.
HP servers draw in cool air through the front door and expel warm air through the rear door. Therefore,
the front and rear rack doors must be adequately ventilated to allow ambient room air to enter the
cabinet, and the rear door must be adequately ventilated to allow the warm air to escape from the
cabinet.
CAUTION: To prevent improper cooling and damage to the equipment, do not block the
ventilation openings.
When vertical space in the rack is not filled by a server or rack component, the gaps between the
components cause changes in airflow through the rack and across the servers. Cover all gaps with
blanking panels to maintain proper airflow.
CAUTION: Always use blanking panels to fill empty vertical spaces in the rack. This
arrangement ensures proper airflow. Using a rack without blanking panels results in improper
cooling that can lead to thermal damage.
The 9000 and 10000 Series Racks provide proper server cooling from flow-through perforations in the
front and rear doors that provide 64 percent open area for ventilation.
CAUTION: When using a Compaq branded 7000 Series rack, you must install the high
airflow rack door insert [P/N 327281-B21 (42U) or P/N 157847-B21 (22U)] to provide
proper front-to-back airflow and cooling.
CAUTION: If a third-party rack is used, observe the following additional requirements to ensure
adequate airflow and to prevent damage to the equipment:
• Front and rear doors—If the 42U rack includes closing front and rear doors, you must allow
5,350 sq cm (830 sq in) of holes evenly distributed from top to bottom to permit adequate
airflow (equivalent to the required 64 percent open area for ventilation).
• Side—The clearance between the installed rack component and the side panels of the rack
must be a minimum of 7 cm (2.75 in).
Temperature requirements
To ensure continued safe and reliable equipment operation, install or position the system in a wellventilated, climate-controlled environment.
Setup
30
The maximum recommended ambient operating temperature (TMRA) for most server products is 35°C
(95°F). The temperature in the room where the rack is located must not exceed 35°C (95°F).
CAUTION: To reduce the risk of damage to the equipment when installing third-party options:
• Do not permit optional equipment to impede airflow around the server or to increase the
internal rack temperature beyond the maximum allowable limits.
• Do not exceed the manufacturer’s TMRA.
Power requirements
Installation of this equipment must comply with local and regional electrical regulations governing the
installation of information technology equipment by licensed electricians. This equipment is designed to
operate in installations covered by NFPA 70, 1999 Edition (National Electric Code) and NFPA-75, 1992
(code for Protection of Electronic Computer/Data Processing Equipment). For electrical power ratings on
options, refer to the product rating label or the user documentation supplied with that option.
WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not
overload the AC supply branch circuit that provides power to the rack. Consult the electrical
authority having jurisdiction over wiring and installation requirements of your facility.
CAUTION: Protect the server from power fluctuations and temporary interruptions with a
regulating uninterruptible power supply (UPS). This device protects the hardware from damage
caused by power surges and voltage spikes and keeps the system in operation during a power
failure.
When installing more than one server, you may need to use additional power distribution devices to
safely provide power to all devices. Observe the following guidelines:
•
Balance the server power load between available AC supply branch circuits.
•
Do not allow the overall system AC current load to exceed 80 percent of the branch circuit AC
current rating.
•
Do not use common power outlet strips for this equipment.
•
Provide a separate electrical circuit for the server.
Electrical grounding requirements
The server must be grounded properly for proper operation and safety. In the United States, you must
install the equipment in accordance with NFPA 70, 1999 Edition (National Electric Code), Article 250,
as well as any local and regional building codes. In Canada, you must install the equipment in
accordance with Canadian Standards Association, CSA C22.1, Canadian Electrical Code. In all other
countries, you must install the equipment in accordance with any regional or national electrical wiring
codes, such as the International Electrotechnical Commission (IEC) Code 364, parts 1 through 7.
Furthermore, you must be sure that all power distribution devices used in the installation, such as branch
wiring and receptacles, are listed or certified grounding-type devices.
Because of the high ground-leakage currents associated with multiple servers connected to the same
power source, HP recommends the use of a PDU that is either permanently wired to the building’s branch
circuit or includes a nondetachable cord that is wired to an industrial-style plug. NEMA locking-style plugs
or those complying with IEC 60309 are considered suitable for this purpose. Using common power outlet
strips for the server is not recommended.
Setup
31
Rack warnings
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:
• The leveling jacks are extended to the floor.
• The full weight of the rack rests on the leveling jacks.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.
WARNING: To reduce the risk of personal injury or equipment damage when unloading a
rack:
• At least two people are needed to safely unload the rack from the pallet. An empty 42U
rack can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and
may become unstable when being moved on its casters.
• Never stand in front of the rack when it is rolling down the ramp from the pallet. Always
handle the rack from both sides.
WARNING: Components can be very heavy. To reduce the risk of personal injury or damage
to the equipment:
• Remove all pluggable power supplies and modules to reduce the weight of the product
before lifting it.
• Observe local occupational health and safety requirements and guidelines for manual
material handling.
• Get help to lift and stabilize the product during installation or removal, especially when the
product is not fastened to the rails. When the component weighs more than 22.5 kg (50
lb), at least two people must lift the component into the rack together. If the component is
loaded into the rack above chest level, a third person must assist in aligning the rails while
the other two support the component.
• Use caution when installing the component in or removing the component from the rack; it
is unstable when not fastened to the rails.
Identifying the contents of the server shipping carton
Unpack the server shipping carton and locate the materials and documentation necessary for installing the
server. All the rack mounting hardware necessary for installing the server into the rack is included with the
rack or the server.
The contents of the server shipping carton include:
•
Server
•
Power cord
•
Hardware documentation, Documentation CD, and software products
•
Rack-mounting hardware
Setup
32
In addition to the supplied items, you may need:
•
Operating system or application software
•
Hardware options
Installing hardware options
Install any hardware options before initializing the server. For options installation information, refer to the
option documentation. For server-specific information, refer to "Hardware options installation (on page
37)."
Installing the server into the rack
CAUTION: Always plan the rack installation so that the heaviest item is on the bottom of the
rack. Install the heaviest item first, and continue to populate the rack from the bottom to the top.
1.
Install the server and cable management arm into the rack. For more information, refer to the
installation instructions that ship with the 2U Quick Deploy Rail System.
2.
Connect peripheral devices to the server.
Item
Description
Color
1
Expansion slot 1
—
2
Expansion slot 2
—
3
Expansion slot 3
—
4
Expansion slot 4
—
5
Expansion slot 5
—
6
T-10/T-15 Torx screwdriver
—
7
External option blank
—
8
NIC 2 connector
—
9
NIC 1 connector
—
Setup
33
10
Power supply bay 2
—
11
Power cord connector
Black
12
Power supply bay 1 (populated)
—
13
iLO 2 connector
—
14
Video connector
Blue
15
USB connectors (2)
Black
16
Serial connector
—
17
Mouse connector
Green
18
Keyboard connector
Purple
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do not plug
telephone or telecommunications connectors into RJ-45 connectors.
3.
Connect the power cord to the rear of the server.
4.
Install the power cord anchor on the handle of the power supply.
NOTE: Peripheral device cables are removed for clarity.
5.
Secure cables to the cable management arm.
IMPORTANT: When using cable management arm components, be sure to leave enough slack
in each of the cables to prevent damage to the cables when the server is extended from the
rack.
Setup
34
6.
Connect the power cord to the AC power source.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against
it. Pay particular attention to the plug, electrical outlet, and the point where the cord
extends from the server.
Powering up and configuring the server
To power up the server, press the Power On/Standby button.
While the server boots, RBSU and the ORCA utility are automatically configured to prepare the server for
operating system installation.
To configure these utilities manually:
•
Press the F8 key when prompted during the array controller initialization to configure the array
controller using ORCA.
•
Press the F9 key when prompted during the boot process to change the server settings using RBSU.
The system is set up by default for the English language.
For more information on the automatic configuration, refer to the HP ROM-Based Setup Utility User Guide
located on the Documentation CD.
Installing the operating system
To operate properly, the server must have a supported operating system installed. For the latest
information on supported operating systems, refer to the HP website (http://www.hp.com/go/supportos).
Setup
35
Methods to install an operating system on the server include:
•
SmartStart assisted installation—Insert the SmartStart CD into the CD-ROM drive and reboot the
server.
•
Manual installation—Insert the operating system CD into the CD-ROM drive and reboot the server.
This process may require you to obtain additional drivers from the HP website
(http://www.hp.com/support).
For information on using these installation paths, refer to the SmartStart installation poster in the HP
ProLiant Essentials Foundation Pack, included with the server.
Registering the server
To register the server, refer to the HP Registration website (http://register.hp.com).
Setup
36
Hardware options installation
Introduction
If more than one option is being installed, read the installation instructions for all the hardware options
and identify similar steps to streamline the installation process.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: To prevent damage to electrical components, properly ground the server before
beginning any installation procedure. Improper grounding can cause electrostatic discharge.
Processor option
CAUTION: To avoid damage to the processor and system board, only authorized personnel
should attempt to replace or install the processor in this server.
CAUTION: To help avoid damage to the processor and system board, do not install the
processor without using the processor installation tool.
CAUTION: To prevent possible server malfunction and damage to the equipment,
multiprocessor configurations must contain processors with the same part number.
IMPORTANT: If upgrading processor speed, update the system ROM before installing the
processor.
IMPORTANT: Processor socket 1 must be populated at all times or the server does not function
properly.
To install a processor:
1.
Power down the server (on page 21).
2.
Extend the server from the rack (on page 21).
3.
Remove the access panel (on page 22).
4.
Remove the air baffle (on page 23).
Hardware options installation
37
5.
Open the heatsink retaining bracket.
CAUTION: The pins on the processor socket are very fragile. Any damage to them may
require replacing the system board.
6.
Remove the processor socket protective cover. Retain the cover for future use.
CAUTION: Failure to completely open the processor locking lever prevents the processor from
seating during installation, leading to hardware damage.
Hardware options installation
38
7.
Rotate the latch and open the retaining bracket.
IMPORTANT: Be sure the processor remains inside the processor installation tool.
8.
If the processor has separated from the installation tool, carefully re-insert the processor in the tool.
9.
Align the processor installation tool with the socket and install the processor.
CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides
on the processor and socket to properly align the processor with the socket.
Hardware options installation
39
10.
Press down firmly until the processor installation tool clicks and separates from the processor, and
then remove the processor installation tool.
Hardware options installation
40
11.
Close the processor retaining bracket and the processor retaining latch.
CAUTION: To prevent possible server malfunction or damage to the equipment, be sure to
completely close the processor locking lever.
12.
Remove the heatsink cover.
CAUTION: After the cover is removed, do not touch the thermal interface media.
Hardware options installation
41
13.
Install the heatsink.
14.
Close the heatsink retaining bracket.
15.
Install the air baffle (on page 24).
16.
Install the access panel (on page 23).
17.
Install the server into the rack.
18.
Power up the server (on page 21).
Memory options
You can expand server memory by installing PC2-5300 Registered DDR2 SDRAM DIMMs. The server
supports up to 32 GB of memory using eight 4-GB DIMMs (four DIMMs per processor).
For DIMM slot locations and bank assignments, see "DIMM slots (on page 13)."
Hardware options installation
42
Advanced ECC memory
This server uses Advanced ECC for memory protection. In Advanced ECC, the server is protected against
correctable memory errors. The server provides notification if the level of correctable errors exceeds a predefined threshold rate. The server does not fail because of correctable memory errors. Advanced ECC
provides additional protection over Standard ECC because it is possible to correct certain memory errors
that would otherwise be uncorrectable and result in a server failure.
Whereas standard ECC can correct single-bit memory errors, Advanced ECC can correct single-bit
memory errors and multi-bit memory errors if all failed bits are on the same DRAM device on the DIMM.
DIMM installation guidelines
Observe the following guidelines when installing additional memory:
•
Always install memory in pairs of two identical DIMMs.
•
Install only ECC PC2-5300 Registered DDR2 SDRAM DIMMs that meet the following specifications:
o
Supply voltage: 1.8 V
o
Bus width: 72 bits
•
Install DIMMs with the same speed.
•
Install memory in pairs (banks) beginning with banks farthest away from each populated processor
(banks A and C).
•
Observe the following special conditions when installing memory with a second processor:
o
Processor 2 can be installed without memory.
o
Any memory installed into banks for processor 2 can be used only if processor 2 is installed.
CAUTION: Always wear an antistatic wrist strap when working inside the server.
DIMM population order
Configuration
Bank A
Bank B
Bank C
Bank D
1A and 2A
3B and 4B
5C and 6C
7D and 8D
Single processor
1st
2nd
—
—
Dual processor
1st
3rd
2nd
4th
Installing DIMMs
1.
Power down the server (on page 21).
2.
Extend the server from the rack (on page 21).
3.
Remove the access panel (on page 22).
4.
Remove the air baffle (on page 23).
5.
Open the DIMM slot latches.
Hardware options installation
43
IMPORTANT: Always install memory in pairs of two identical DIMMs.
6.
Install the DIMM.
7.
Install the air baffle (on page 24).
8.
Install the access panel (on page 23).
9.
Install the server into the rack.
10.
Power up the server (on page 21).
For more information about LEDs and troubleshooting failed DIMMs, see "Systems Insight Display LEDs
and internal health LED combinations (on page 14)."
Hot-plug SAS hard drive options
When adding hard drives to the server, observe the following general guidelines:
•
The system automatically sets all device numbers.
•
If only one hard drive is used, install it in the bay with the lowest device number.
•
Hard drives must be SFF types.
•
Drives should be the same capacity to provide the greatest storage space efficiency when drives are
grouped together into the same drive array.
Hardware options installation
44
Installing a hot-plug SAS hard drive
1.
Remove the SAS hard drive blank.
2.
Prepare the hard drive.
Hardware options installation
45
3.
Install the hard drive.
4.
Determine the status of the hard drive from the hot-plug SAS hard drive LED combinations ("SAS and
SATA hard drive LED combinations" on page 17).
Removing a hot-plug SAS hard drive
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
1.
Determine the status of the hard drive from the hot-plug SAS hard drive LED combinations ("SAS and
SATA hard drive LED combinations" on page 17).
2.
Back up all server data on the hard drive.
3.
Remove the hard drive.
Hardware options installation
46
Media drive option
1.
Power down the server (on page 21).
2.
Remove the existing media drive option or blank.
3.
Slide the CD/DVD-ROM drive or diskette drive into the drive bay.
Redundant hot-plug AC power supply option
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
1.
Access the product rear panel (on page 27).
2.
Remove the power supply blank.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or
power supply blank to cool before touching it.
Hardware options installation
47
3.
Slide the power supply into the power supply bay.
4.
Connect the power cord to the power supply.
5.
Route the power cord through the power cord anchor or cable management arm.
6.
Reposition the cable management arm into the operating position.
7.
Connect the power cord to the power source.
8.
Be sure that the power supply LED is green ("Rear panel LEDs and buttons" on page 11).
9.
Be sure that the front panel external health LED is green ("Front panel LEDs and buttons" on page 7).
DC power supply option
Hardware options installation
48
WARNING: To reduce the risk of electric shock, fire, and damage to the equipment, this
product must be installed in accordance with the following guidelines:
• This power supply is intended only for installation in HP servers located in a restricted
access location.
• This power supply is not intended for direct connection to the DC supply branch circuit. It
should only be connected to a power distribution unit (PDU) that provides an independent
overcurrent-protected output for each DC power supply. Each output overcurrent-protected
device in the PDU must be suitable for interrupting fault current available from the DC
power source and must be rated no more than 50A.
• This power supply is designed to be connected only to a DC power source that can be
classified as SELV or TNV, in accordance with applicable national requirements for
Information Technology Equipment and Telecommunications Equipment. Generally, these
requirements are based on the International Standard for Information Technology
Equipment, IEC 60950, and/or the European Telecommunication Standard ETS 300 1322. The DC source is to have one pole (Neutral/Return) reliably connected to earth ground
in accordance with local/regional electric codes and/or regulations.
• The green/yellow lead of the power cable assembly must be connected to a suitable
ground/earth terminal. This terminal must be connected to a suitable building ground/earth
terminal in accordance with local/regional electric codes/regulations. Do not rely on the
rack or cabinet chassis to provide adequate ground/earth continuity.
WARNING: To reduce the risk of personal injury or damage to the equipment, the installation
of power supplies should be performed only by individuals who are qualified in servicing
server equipment and trained to deal with products capable of producing hazardous energy
levels.
WARNING: To reduce the risk of personal injury from hot surfaces, observe the thermal labels
on each power supply or module.
WARNING: To reduce the risk of injury from electric shock hazards, do not open power
supplies. Refer all maintenance, upgrades, and servicing to qualified personnel.
CAUTION: Do not run the server with one AC power supply and one DC power supply
installed.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be sure that you
are properly grounded (earthed) before beginning any installation procedure.
To install the component:
Hardware options installation
49
1.
Remove the power supply blank.
WARNING: To reduce the risk of electric shock or damage to the equipment, do not connect
the power cord to the power supply until the power supply is installed.
2.
Slide the power supply into the power supply bay until the release/lock lever clicks, securing the
power supply.
3.
Connect the power cord to the power supply.
4.
Tighten the two retaining screws on either side of the power cord connector.
5.
Route the power cord:
o
If the cable management arm has a left-hand swing, route the power cord through the cable
management arm.
o
If the cable management arm has a right-hand swing, remove the cable management arm or
convert it for left-hand swing. For removal instructions, see "Cable management arm with righthand swing (on page 27)." For conversion instructions, see the instructions that ship with the 2U
Quick Deploy Rail System.
Hardware options installation
50
6.
Connect the power cord to the DC power source.
7.
Be sure that the power supply and external health LEDs are illuminated green.
Expansion board options
The server supports PCI, PCI-X, and PCI Express expansion boards.
Installing an expansion board (slot 2)
1.
Power down the server (on page 21).
2.
Extend the server from the rack (on page 21).
3.
Remove the access panel (on page 22).
4.
Remove the expansion slot cover.
5.
Install the expansion board.
6.
Connect any required internal or external cables to the expansion board. Refer to the documentation
that ships with the expansion board.
7.
Install the access panel (on page 23).
8.
Install the server into the rack.
9.
Power up the server (on page 21).
Removing an expansion slot cover (slot 3, 4, or 5)
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all PCI slots have either an expansion slot cover or an expansion board installed.
1.
Power down the server (on page 21).
2.
Extend the server from the rack (on page 21).
Hardware options installation
51
3.
Remove the access panel (on page 22).
4.
Remove the PCI riser cage (on page 25).
5.
Remove the expansion slot cover.
Installing an expansion board (slot 3, 4, or 5)
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
1.
Power down the server (on page 21).
2.
Extend the server from the rack (on page 21).
3.
Remove the access panel (on page 22).
4.
Remove the PCI riser cage (on page 25).
5.
Remove the expansion slot cover ("Removing an expansion slot cover (slot 3, 4, or 5)" on page 51).
6.
Unlock the PCI retaining clip.
Hardware options installation
52
7.
Install the expansion board.
8.
Lock the PCI retaining clip.
9.
If installing an x16 expansion board that requires a power cable, connect the PCIe x16 riser board
power cable to the expansion board and the PCI riser board ("PCIe x16 riser board power cabling"
on page 58).
10.
Install the PCI riser cage (on page 25).
11.
Connect any required internal or external cables to the expansion board. Refer to the documentation
that ships with the expansion board.
12.
Install the access panel (on page 23).
13.
Install the server into the rack.
14.
Power up the server (on page 21).
PCI riser board option
To install the component:
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all PCI slots have either an expansion slot cover or an expansion board installed.
1.
Power down the server (on page 21).
2.
Extend the server from the rack (on page 21).
3.
Remove the access panel (on page 22).
4.
Remove the PCI riser cage (on page 25).
5.
Remove any expansion boards.
Hardware options installation
53
6.
Remove the PCI riser board.
7.
Install the optional riser board.
8.
Install any expansion boards. ("Expansion board options" on page 51)
9.
Install the PCI riser cage (on page 25).
10.
Install the access panel (on page 23).
11.
Install the server into the rack.
12.
Power up the server (on page 21).
Hardware options installation
54
Cabling
SAS hard drive cabling
PCI SAS cabling to an HP Smart Array P400i Controller
PCI SAS cabling to an optional expansion board controller
Cabling 55
Fan board cabling
Battery cabling for BBWC
Cabling 56
Systems Insight Display cabling
Hard drive backplane power cabling
Cabling 57
Media drive bay cabling
PCIe x16 riser board power cabling
Cabling 58
Software and configuration utilities
Configuration tools
SmartStart software
SmartStart is a collection of software that optimizes single-server setup, providing a simple and consistent
way to deploy server configuration. SmartStart has been tested on many ProLiant server products,
resulting in proven, reliable configurations.
SmartStart assists the deployment process by performing a wide range of configuration activities,
including:
•
Configuring hardware using embedded configuration utilities, such as RBSU and ORCA
•
Preparing the system for installing "off-the-shelf" versions of leading operating system software
•
Installing optimized server drivers, management agents, and utilities automatically with every
assisted installation
•
Testing server hardware using the Insight Diagnostics Utility ("HP Insight Diagnostics" on page 67)
•
Installing software drivers directly from the CD. With systems that have internet connection, the
SmartStart Autorun Menu provides access to a complete list of ProLiant system software.
•
Enabling access to the Array Configuration Utility (on page 61), Array Diagnostic Utility (on page
68), and Erase Utility (on page 64)
SmartStart is included in the HP ProLiant Essentials Foundation Pack. For more information about
SmartStart software, refer to the HP ProLiant Essentials Foundation Pack or the HP website
(http://h18013.www1.hp.com/products/servers/management/smartstart/index.html).
SmartStart Scripting Toolkit
The SmartStart Scripting Toolkit is a server deployment product that delivers an unattended automated
installation for high-volume server deployments. The SmartStart Scripting Toolkit is designed to support
ProLiant BL, ML, and DL servers. The toolkit includes a modular set of utilities and important documentation
that describes how to apply these new tools to build an automated server deployment process.
Using SmartStart technology, the Scripting Toolkit provides a flexible way to create standard server
configuration scripts. These scripts are used to automate many of the manual steps in the server
configuration process. This automated server configuration process cuts time from each server deployed,
making it possible to scale server deployments to high volumes in a rapid manner.
For more information, and to download the SmartStart Scripting Toolkit, refer to the HP website
(http://www.hp.com/servers/sstoolkit).
Software and configuration utilities 59
Configuration Replication Utility
CONREP is shipped in the SmartStart Scripting Toolkit and is a program that works with RBSU to replicate
hardware configuration on ProLiant servers. This utility is run during State 0, Run Hardware Configuration
Utility, when doing a scripted server deployment. CONREP reads the state of the system environment
variables to determine the configuration and then writes the results to an editable script file. This file can
then be deployed across multiple servers with similar hardware and software components. For more
information, refer to the SmartStart Scripting Toolkit User Guide on the HP website
(http://h18004.www1.hp.com/products/servers/management/toolkit/documentation.html).
HP ROM-Based Setup Utility
RBSU is a configuration utility embedded in ProLiant servers that performs a wide range of configuration
activities that can include the following:
•
Configuring system devices and installed options
•
Enabling and disabling system features
•
Displaying system information
•
Selecting the primary boot controller
•
Configuring memory options
•
Language selection
For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD
or the HP website (http://www.hp.com/support/smartstart/documentation).
Using RBSU
To use RBSU, use the following keys:
•
To access RBSU, press the F9 key during power-up when prompted.
•
To navigate the menu system, use the arrow keys.
•
To make selections, press the Enter key.
•
To access Help for a highlighted configuration option, press the F1 key.
IMPORTANT: RBSU automatically saves settings when you press the Enter key. The utility does
not prompt you for confirmation of settings before you exit the utility. To change a selected
setting, you must select a different setting and press the Enter key.
Default configuration settings are applied to the server at one of the following times:
•
Upon the first system power-up
•
After defaults have been restored
Default configuration settings are sufficient for proper typical server operation, but configuration settings
can be modified using RBSU. The system will prompt you for access to RBSU with each power-up.
Auto-configuration process
The auto-configuration process automatically runs when you boot the server for the first time. During the
power-up sequence, the system ROM automatically configures the entire system without needing any
Software and configuration utilities 60
intervention. During this process, the ORCA utility, in most cases, automatically configures the array to a
default setting based on the number of drives connected to the server.
NOTE: The server may not support all the following examples.
NOTE: If the boot drive is not empty or has been written to in the past, ORCA does not
automatically configure the array. You must run ORCA to configure the array settings.
Drives installed
Drives used
RAID level
1
1
RAID 0
2
2
RAID 1
3, 4, 5, or 6
3, 4, 5, or 6
RAID 5
More than 6
0
None
To change any ORCA default settings and override the auto-configuration process, press the F8 key when
prompted.
By default, the auto-configuration process configures the system for the English language. To change any
default settings in the auto-configuration process (such as the settings for language, operating system, and
primary boot controller), execute RBSU by pressing the F9 key when prompted. After the settings are
selected, exit RBSU and allow the server to reboot automatically.
For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD
or the HP website (http://www.hp.com/support/smartstart/documentation).
Boot options
Near the end of the boot process, the boot options screen is displayed. This screen is visible for several
seconds before the system attempts to boot from a diskette, CD, or hard drive. During this time, you can
do the following:
•
Access RBSU by pressing the F9 key
•
Access the System Maintenance Menu (which enables you to launch ROM-based Diagnostics or
Inspect) by pressing the F10 key
•
Force a PXE Network boot by pressing the F12 key
BIOS Serial Console
BIOS Serial Console allows you to configure the serial port to view POST error messages and run RBSU
remotely through a serial connection to the server COM port. The server that you are remotely configuring
does not require a keyboard and mouse.
For more information about BIOS Serial Console, see the BIOS Serial Console User Guide on the
Documentation CD or the HP website (http://www.hp.com/support/smartstart/documentation).
Array Configuration Utility
ACU is a browser-based utility with the following features:
•
Runs as a local application or remote service
Software and configuration utilities 61
•
Supports online array capacity expansion, logical drive extension, assignment of online spares, and
RAID or stripe size migration
•
Suggests the optimum configuration for an unconfigured system
•
Provides different operating modes, enabling faster configuration or greater control over the
configuration options
•
Remains available any time that the server is on
•
Displays on-screen tips for individual steps of a configuration procedure
For optimum performance, the minimum display settings are 800 × 600 resolution and 256 colors.
Servers running Microsoft® operating systems require Internet Explorer 5.5 (with Service Pack 1) or later.
For Linux servers, refer to the README.TXT file for additional browser and support information.
For more information, refer to the Configuring Arrays on HP Smart Array Controllers Reference Guide on
the Documentation CD or the HP website (http://www.hp.com).
Option ROM Configuration for Arrays
Before installing an operating system, you can use the ORCA utility to create the first logical drive, assign
RAID levels, and establish online spare configurations.
The utility also provides support for the following functions:
•
Reconfiguring one or more logical drives
•
Viewing the current logical drive configuration
•
Deleting a logical drive configuration
•
Setting the controller to be the boot controller
If you do not use the utility, ORCA will default to the standard configuration.
For more information regarding array controller configuration, refer to the controller user guide.
For more information regarding the default configurations that ORCA uses, refer to the HP ROM-Based
Setup Utility User Guide on the Documentation CD.
HP ProLiant Essentials Rapid Deployment Pack
The RDP software is the preferred method for rapid, high-volume server deployments. The RDP software
integrates two powerful products: Altiris Deployment Solution and the HP ProLiant Integration Module.
The intuitive graphical user interface of the Altiris Deployment Solution console provides simplified pointand-click and drag-and-drop operations that enable you to deploy target servers, including server blades,
remotely. It enables you to perform imaging or scripting functions and maintain software images.
For more information about the RDP, refer to the HP ProLiant Essentials Rapid Deployment Pack CD or
refer to the HP website (http://www.hp.com/servers/rdp).
Re-entering the server serial number and product ID
After you replace the system board, you must re-enter the server serial number and the product ID.
1.
During the server startup sequence, press the F9 key to access RBSU.
2.
Select the System Options menu.
Software and configuration utilities 62
3.
Select Serial Number. The following warning is displayed:
WARNING! WARNING! WARNING! The serial number is loaded into the system
during the manufacturing process and should NOT be modified. This option
should only be used by qualified service personnel. This value should
always match the serial number sticker located on the chassis.
4.
Press the Enter key to clear the warning.
5.
Enter the serial number and press the Enter key.
6.
Select Product ID.
7.
Enter the product ID and press the Enter key.
8.
Press the Esc key to close the menu.
9.
Press the Esc key to exit RBSU.
10.
Press the F10 key to confirm exiting RBSU. The server will automatically reboot.
Management tools
Automatic Server Recovery
ASR is a feature that causes the system to restart when a catastrophic operating system error occurs, such
as a blue screen, ABEND, or panic. A system fail-safe timer, the ASR timer, starts when the System
Management driver, also known as the Health Driver, is loaded. When the operating system is
functioning properly, the system periodically resets the timer. However, when the operating system fails,
the timer expires and restarts the server.
ASR increases server availability by restarting the server within a specified time after a system hang or
shutdown. At the same time, the HP SIM console notifies you by sending a message to a designated
pager number that ASR has restarted the system. You can disable ASR from the HP SIM console or
through RBSU.
ROMPaq utility
The ROMPaq utility enables you to upgrade the system firmware (BIOS) or Lights-Out 100 firmware. To
upgrade the firmware, insert a ROMPaq diskette into the diskette drive or ROMPaq USB Key into an
available USB port and boot the system.
The ROMPaq utility checks the system and provides a choice (if more than one exists) of available
firmware revisions.
For more information about the ROMPaq utility, see the HP website (http://www.hp.com/go/support).
System Online ROM flash component utility
The Online ROM Flash Component Utility enables system administrators to efficiently upgrade system or
controller ROM images across a wide range of servers and array controllers. This tool has the following
features:
•
Works offline and online
•
Supports Microsoft® Windows NT®, Windows® 2000, Windows Server™ 2003, Novell Netware,
and Linux operating systems
Software and configuration utilities 63
IMPORTANT: This utility supports operating systems that may not be supported by the server.
For operating systems supported by the server, see the HP website
(http://www.hp.com/support).
•
Integrates with other software maintenance, deployment, and operating system tools
•
Automatically checks for hardware, firmware, and operating system dependencies, and installs only
the correct ROM upgrades required by each target server
To download the tool and for more information, see the HP website (http://www.hp.com/support).
Integrated Lights-Out 2 technology
The iLO 2 subsystem is a standard component of selected ProLiant servers that provides server health and
remote server manageability. The iLO 2 subsystem includes an intelligent microprocessor, secure memory,
and a dedicated network interface. This design makes iLO 2 independent of the host server and its
operating system. The iLO 2 subsystem provides remote access to any authorized network client, sends
alerts, and provides other server management functions.
Using iLO 2, you can:
•
Remotely power up, power down, or reboot the host server.
•
Send alerts from iLO 2 regardless of the state of the host server.
•
Access advanced troubleshooting features through the iLO 2 interface.
•
Diagnose iLO 2 using HP SIM through a web browser and SNMP alerting.
For more information about iLO 2 features, refer to the iLO 2 documentation on the Documentation CD or
on the HP website (http://www.hp.com/servers/lights-out).
Erase Utility
CAUTION: Perform a backup before running the System Erase Utility. The utility sets the system
to its original factory state, deletes the current hardware configuration information, including
array setup and disk partitioning, and erases all connected hard drives completely. Refer to the
instructions for using this utility.
Run the Erase Utility if you must erase the system for the following reasons:
•
You want to install a new operating system on a server with an existing operating system.
•
You encounter an error when completing the steps of a factory-installed operating system installation.
The Erase Utility can be accessed from the Maintenance Utilities menu of the SmartStart CD ("SmartStart
software" on page 59).
StorageWorks library and tape tools
HP StorageWorks L&TT provides functionality for firmware downloads, verification of device operation,
maintenance procedures, failure analysis, corrective service actions, and some utility functions. It also
provides seamless integration with HP hardware support by generating and emailing support tickets that
deliver a snapshot of the storage system.
Software and configuration utilities 64
For more information, and to download the utility, refer to the StorageWorks L&TT website
(http://h18006.www1.hp.com/products/storageworks/ltt).
HP Systems Insight Manager
HP SIM is a web-based application that allows system administrators to accomplish normal administrative
tasks from any remote location, using a web browser. HP SIM provides device management capabilities
that consolidate and integrate management data from HP and third-party devices.
IMPORTANT: You must install and use HP SIM to benefit from the Pre-Failure Warranty for
processors, SAS and SCSI hard drives, and memory modules.
For additional information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack or
the HP SIM website (http://www.hp.com/go/hpsim).
Management Agents
Management Agents provide the information to enable fault, performance, and configuration
management. The agents allow easy manageability of the server through HP SIM software, and thirdparty SNMP management platforms. Management Agents are installed with every SmartStart assisted
installation or can be installed through the HP PSP. The Systems Management homepage provides status
and direct access to in-depth subsystem information by accessing data reported through the Management
Agents. For additional information, refer to the Management CD in the HP ProLiant Essentials Foundation
Pack or the HP website (http://www.hp.com/servers/manage).
Redundant ROM support
The server enables you to upgrade or configure the ROM safely with redundant ROM support. The server
has a 4-MB ROM that acts as two, separate 2-MB ROMs. In the standard implementation, one side of the
ROM contains the current ROM program version, while the other side of the ROM contains a backup
version.
NOTE: The server ships with the same version programmed on each side of the ROM.
Safety and security benefits
When you flash the system ROM, ROMPaq writes over the backup ROM and saves the current ROM as a
backup, enabling you to switch easily to the alternate ROM version if the new ROM becomes corrupted
for any reason. This feature protects the existing ROM version, even if you experience a power failure
while flashing the ROM.
Access to redundant ROM settings
To access the redundant ROM through RBSU:
1.
Access RBSU by pressing the F9 key during powerup when the prompt is displayed in the upper
right corner of the screen.
2.
Select Advanced Options.
3.
Select Redundant ROM Selection.
Software and configuration utilities 65
4.
Select the ROM version.
5.
Press the Enter key.
6.
Press the Esc key to exit the current menu or press the F10 key to exit RBSU. The server restarts
automatically.
To access the redundant ROM manually:
1.
Power down the server (on page 21).
2.
Remove the access panel (on page 22).
3.
Set positions 1, 5, and 6 of the system maintenance switch to On.
4.
Install the access panel (on page 23).
5.
Power up the server (on page 21).
6.
Wait for the server to emit two beeps.
7.
Repeat steps 1 and 2.
8.
Set positions 1, 5, and 6 of the system maintenance switch to Off.
9.
Repeat steps 4 and 5.
When the server boots, the system identifies whether the current ROM bank is corrupt. If a corrupt ROM is
detected, the system boots from the backup ROM and alerts you through POST or IML that the ROM bank
is corrupt.
If both the current and backup versions of the ROM are corrupt, the server automatically enters ROMPaq
disaster recovery mode.
USB support
HP provides both standard USB support and legacy USB support. Standard support is provided by the
operating system through the appropriate USB device drivers. HP provides support for USB devices prior
to the operating system loading through legacy USB support, which is enabled by default in the system
ROM. HP hardware supports USB version 2.0.
Legacy USB support provides USB functionality in environments where USB support is normally not
available. Specifically, HP provides legacy USB functionality at:
•
POST
•
RBSU
•
Diagnostics
•
DOS
•
Environments which do not support USB natively
For more information on ProLiant USB support, refer to the HP website
(http://www.compaq.com/products/servers/platforms/usb-support.html).
Changing the USB version support
The factory default setting for this server is USB version 1.1. After the OS has loaded, this setting can be
changed to USB version 2.0 using the following steps:
1.
Access RBSU by pressing F9 during power up.
2.
Select System Options.
Software and configuration utilities 66
3.
Select USB External Port Capability.
4.
Press Enter to display USB 1.1 and USB 2.0 selections.
5.
Arrow down to highlight USB 2.0.
6.
Press Enter.
7.
Press F10 to save the change and exit RBSU.
Internal USB functionality
An internal USB connector is available for use with USB drive keys only. This solution provides for use of
a permanent boot drive from a USB drive key installed in the internal connector, avoiding issues of
clearance on the front of the rack and physical access to secure data.
For additional security, you can disable the external USB connectors through RBSU. Disabling the rear
USB connectors in RBSU disables both rear USB ports.
Diagnostic tools
HP Insight Diagnostics
HP Insight Diagnostics is a proactive server management tool, available in both offline and online
versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify
server installations, troubleshoot problems, and perform repair validation.
HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the
OS is not running. To run this utility, launch the SmartStart CD.
HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and
other related data needed for effective server management. Available in Microsoft® Windows® and
Linux versions, the utility helps to ensure proper system operation.
For more information or to download the utility, refer to the HP website
(http://www.hp.com/servers/diags).
HP Insight Diagnostics survey functionality
HP Insight Diagnostics (on page 67) provides survey functionality that gathers critical hardware and
software information on ProLiant servers.
This functionality supports operating systems that may not be supported by the server. For operating
systems supported by the server, see the HP website (http://www.hp.com/go/supportos).
If a significant change occurs between data-gathering intervals, the survey function marks the previous
information and overwrites the survey data files to reflect the latest changes in the configuration.
Survey functionality is installed with every SmartStart-assisted HP Insight Diagnostics installation, or it can
be installed through the HP PSP ("ProLiant Support Packs" on page 69).
NOTE: The current version of SmartStart provides the memory spare part numbers for the
server. To download the latest version, see the HP website (http://www.hp.com/support).
Software and configuration utilities 67
Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each
event with 1-minute granularity.
You can view recorded events in the IML in several ways, including the following:
•
From within HP SIM ("HP Systems Insight Manager" on page 65)
•
From within Survey Utility
•
From within operating system-specific IML viewers
o
For NetWare: IML Viewer
o
For Windows®: IML Viewer
o
For Linux: IML Viewer Application
•
From within the iLO 2 user interface
•
From within HP Insight Diagnostics (on page 67)
For more information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack.
Array Diagnostic Utility
The HP Array Diagnostics Utility is a web-based application that creates a report of all HP storage
controllers and disk drives. This report provides vital information to assist in identifying faults or conditions
that may require attention. ADU can be accessed from the SmartStart CD ("SmartStart software" on page
59) or downloaded from the HP website (http://www.hp.com).
Remote support and analysis tools
HP Instant Support Enterprise Edition
ISEE is a proactive remote monitoring and diagnostic tool to help manage your systems and devices, a
feature of HP support. ISEE provides continuous hardware event monitoring and automated notification to
identify and prevent potential critical problems. Through remote diagnostic scripts and vital system
configuration information collected about your systems, ISEE enables fast restoration of your systems.
Install ISEE on your systems to help mitigate risk and prevent potential critical problems.
For more information on ISEE, refer to the HP website
(http://www.hp.com/hps/hardware/hw_enterprise.html).
To download HP ISEE, visit the HP website (http://www.hp.com/hps/hardware/hw_downloads.html).
For installation information, refer to the HP ISEE Client Installation and Upgrade Guide
(ftp://ftp.hp.com/pub/services/hardware/info/isee_client.pdf).
Web-Based Enterprise Service
WEBES enables administrators to manage hardware events proactively, either locally or online. The
service provides real-time multiple event analysis, crash analysis, and notification, locally through SMTP
and remotely through ISEE for OpenVMS, Tru64, and Microsoft® Windows® operating system binary
error logs.
Software and configuration utilities 68
For more information, refer to the HP website (http://h18000.www1.hp.com/support/svctools/).
Open Services Event Manager
OSEM is a standalone tool that performs real-time reactive and proactive service event filtering, analysis,
and notification. The tool gathers event data from SNMP traps or information provided over an HTTP
interface and notifies an administrator or HP through SMTP and ISEE.
For more information, refer to the HP website (http://h18000.www1.hp.com/support/svctools/).
Keeping the system current
Drivers
The server includes new hardware that may not have driver support on all operating system installation
media.
If you are installing a SmartStart-supported operating system, use the SmartStart software (on page 59)
and its Assisted Path feature to install the operating system and latest driver support.
NOTE: If you are installing drivers from the SmartStart CD or the Software Maintenance CD,
refer to the SmartStart website (http://www.hp.com/servers/smartstart) to be sure that you are
using the latest version of SmartStart. For more information, refer to the documentation
provided with the SmartStart CD.
If you do not use the SmartStart CD to install an operating system, drivers for some of the new hardware
are required. These drivers, as well as other option drivers, ROM images, and value-add software can be
downloaded from the HP website (http://www.hp.com/support).
IMPORTANT: Always perform a backup before installing or updating device drivers.
ProLiant Support Packs
PSPs represent operating system-specific bundles of ProLiant optimized drivers, utilities, and management
agents. Refer to the PSP website
(http://h18000.www1.hp.com/products/servers/management/psp.html).
Operating system version support
Refer to the operating system support matrix (http://www.hp.com/go/supportos).
Change control and proactive notification
HP offers Change Control and Proactive Notification to notify customers 30 to 60 days in advance of
upcoming hardware and software changes on HP commercial products.
For more information, refer to the HP website (http://www.hp.com/go/pcn).
Software and configuration utilities 69
Care Pack
HP Care Pack Services offer upgraded service levels to extend and expand standard product warranty
with easy-to-buy, easy-to-use support packages that help you make the most of your server investments.
Refer to the Care Pack website (http://www.hp.com/hps/carepack/servers/cp_proliant.html).
Software and configuration utilities 70
Troubleshooting
Troubleshooting resources
The HP ProLiant Servers Troubleshooting Guide provides simple procedures for resolving common
problems as well as a comprehensive course of action for fault isolation and identification, error message
interpretation, issue resolution, and software maintenance.
To obtain the guide, refer to any of the following sources and then select the HP ProLiant Servers
Troubleshooting Guide:
•
The server-specific Documentation CD
•
The Business Support Center on the HP website (http://www.hp.com/support). Navigate to the
server technical support page. Under self-help resources, select ProLiant Troubleshooting Guide.
•
The Technical Documentation website (http://www.docs.hp.com). Select Enterprise Servers,
Workstations and Systems Hardware, and then the appropriate server.
Pre-diagnostic steps
WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary
information in the server documentation before removing, replacing, reseating, or modifying
system components
IMPORTANT: This guide provides information for multiple servers. Some information may not
apply to the server you are troubleshooting. Refer to the server documentation for information
on procedures, hardware options, software tools, and operating systems supported by the
server.
1.
Review the important safety information (on page 71).
2.
Gather symptom information (on page 73).
3.
Prepare the server for diagnosis (on page 74).
4.
Use the Start diagnosis flowchart (on page 75) to begin the diagnostic process.
Important safety information
Familiarize yourself with the safety information in the following sections before troubleshooting the server.
Important safety information
Before servicing this product, read the Important Safety Information document provided with the server.
Troubleshooting 71
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially hazardous
conditions.
This symbol indicates the presence of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no
user or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure.
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment,
do not plug telephone or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or hot component. If this surface is
contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
20.41 - 27.22 kg WARNING: To reduce the risk of personal injury or damage to the equipment,
47.18 - 60.0 lb observe local occupational health and safety requirements and guidelines for manual
material handling.
These symbols, on power supplies or systems, indicate that the equipment is supplied
by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords
to completely disconnect power from the system.
Warnings and cautions
WARNING: Only authorized technicians trained by HP should attempt to repair this
equipment. All troubleshooting and repair procedures are detailed to allow only
subassembly/module-level repair. Because of the complexity of the individual boards and
subassemblies, no one should attempt to make repairs at the component level or to make
modifications to any printed wiring board. Improper repairs can create a safety hazard.
Troubleshooting 72
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:
• The leveling feet are extended to the floor.
• The full weight of the rack rests on the leveling feet.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than one
component is extended for any reason.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against
it. Pay particular attention to the plug, electrical outlet, and the point where the cord
extends from the server.
WARNING: To reduce the risk of personal injury or damage to the equipment:
• Observe local occupation health and safety requirements and guidelines for
20.41 - 27.22 kg
manual handling.
47.18 - 60.0 lb
• Obtain adequate assistance to lift and stabilize the chassis during installation or
removal.
• The server is unstable when not fastened to the rails.
• When mounting the server in a rack, remove the power supplies and any other
removable module to reduce the overall weight of the product.
CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of
clearance at the front and back of the server.
CAUTION: The server is designed to be electrically grounded (earthed). To ensure proper
operation, plug the AC power cord into a properly grounded AC outlet only.
Symptom information
Before troubleshooting a server problem, collect the following information:
•
What events preceded the failure? After which steps does the problem occur?
•
What has been changed since the time the server was working?
•
Did you recently add or remove hardware or software? If so, did you remember to change the
appropriate settings in the server setup utility, if necessary?
•
How long has the server exhibited problem symptoms?
•
If the problem occurs randomly, what is the duration or frequency?
Troubleshooting 73
To answer these questions, the following information may be useful:
•
Run HP Insight Diagnostics (on page 67) and use the survey page to view the current configuration
or to compare it to previous configurations.
•
Refer to your hardware and software records for information.
•
Refer to server LEDs and their statuses.
Prepare the server for diagnosis
1.
Be sure the server is in the proper operating environment with adequate power, air conditioning,
and humidity control. Refer to the server documentation for required environmental conditions.
2.
Record any error messages displayed by the system.
3.
Remove all diskettes and CDs from the media drives.
4.
Power down the server and peripheral devices if you will be diagnosing the server offline. Always
perform an orderly shutdown, if possible. This means you must:
a. Exit any applications.
b. Exit the operating system.
c.
Power down the server (on page 21).
5.
Disconnect any peripheral devices not required for testing (any devices not necessary to power up
the server). Do not disconnect the printer if you want to use it to print error messages.
6.
Collect all tools and utilities, such as a Torx screwdriver, loopback adapters, ESD wrist strap, and
software utilities, necessary to troubleshoot the problem.
o
You must have the appropriate Health Drivers and Management Agents installed on the server.
NOTE: To verify the server configuration, connect to the System Management homepage and
select Version Control Agent. The VCA gives you a list of names and versions of all installed
HP drivers, Management Agents, and utilities, and whether they are up to date.
o
HP recommends you have access to the SmartStart CD for value-added software and drivers
required during the troubleshooting process.
o
HP recommends you have access to the server documentation for server-specific information.
Loose connections
Action:
•
Be sure all power cords are securely connected.
•
Be sure all cables are properly aligned and securely connected for all external and internal
components.
•
Remove and check all data and power cables for damage. Be sure no cables have bent pins or
damaged connectors.
•
If a fixed cable tray is available for the server, be sure the cords and cables connected to the server
are routed correctly through the tray.
•
Be sure each device is properly seated. Avoid bending or flexing circuit boards when reseating
components.
•
If a device has latches, be sure they are completely closed and locked.
Troubleshooting 74
•
Check any interlock or interconnect LEDs that may indicate a component is not connected properly.
•
If problems continue to occur, remove and reinstall each device, checking the connectors and sockets
for bent pins or other damage.
Service notifications
To view the latest service notifications, refer to the HP website (http://www.hp.com/go/bizsupport).
Select the appropriate server model, and then click the Troubleshoot a Problem link on the product page.
Troubleshooting flowcharts
To effectively troubleshoot a problem, HP recommends that you start with the first flowchart in this section,
"Start diagnosis flowchart (on page 75)," and follow the appropriate diagnostic path. If the other
flowcharts do not provide a troubleshooting solution, follow the diagnostic steps in "General diagnosis
flowchart (on page 76)." The General diagnosis flowchart is a generic troubleshooting process to be used
when the problem is not server-specific or is not easily categorized into the other flowcharts.
The available flowcharts include:
•
Start diagnosis flowchart (on page 75)
•
General diagnosis flowchart (on page 76)
•
Server power-on problems flowchart (on page 78)
•
POST problems flowchart (on page 81)
•
OS boot problems flowchart (on page 82)
•
Server fault indications flowchart (on page 84)
Start diagnosis flowchart
Use the following flowchart to start the diagnostic process.
Item
Refer to
1
"General diagnosis flowchart (on page 76)"
2
"Power-on problems flowchart ("Server power-on problems flowchart" on
page 78)"
3
"POST problems flowchart (on page 81)"
4
"OS boot problems flowchart (on page 82)"
5
"Server fault indications flowchart (on page 84)"
Troubleshooting 75
General diagnosis flowchart
The General diagnosis flowchart provides a generic approach to troubleshooting. If you are unsure of the
problem, or if the other flowcharts do not fix the problem, use the following flowchart.
Item
Refer to
1
"Symptom information (on page 73)"
2
"Loose connections (on page 74)"
3
"Service notifications (on page 75)"
Troubleshooting 76
Item
Refer to
4
The most recent version of a particular server or option firmware is
available on the following websites:
•
HP Support website (http://www.hp.com/support)
•
HP ROM-BIOS/Firmware Updates website
(http://h18023.www1.hp.com/support/files/server/us/romflash.ht
ml)
5
"General memory problems are occurring" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
6
Server maintenance and service guide, located on the Documentation
CD or the HP website (http://www.hp.com/products/servers/platforms)
7
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
"Server information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
"Operating system information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
8
9
"HP contact information (on page 97)"
Troubleshooting 77
Server power-on problems flowchart
Symptoms:
•
The server does not power on.
•
The system power LED is off or amber.
Troubleshooting 78
•
The external health LED is red or amber.
•
The internal health LED is red or amber.
NOTE: For the location of server LEDs and information on their statuses, refer to the server
documentation.
Possible causes:
•
Improperly seated or faulty power supply
•
Loose or faulty power cord
•
Power source problem
•
Power on circuit problem
•
Improperly seated component or interlock problem
•
Faulty internal component
Item
Refer to
1
"Component identification (on page 7)"
2
"HP Insight Diagnostics (on page 67)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
3
"Loose connections (on page 74)"
4
Server maintenance and service guide, located on the Documentation
CD, or the HP website (http://www.hp.com/products/servers/platforms)
5
"Integrated Management Log (on page 68)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
6
"Power source problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
7
•
"Power supply problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD, or the HP website
(http://www.hp.com/products/servers/platforms)
8
"System open circuits and short circuits" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
Troubleshooting 79
Troubleshooting 80
POST problems flowchart
Symptoms:
•
Server does not complete POST
NOTE: The server has completed POST when the system attempts to access the boot device.
•
Server completes POST with errors
Possible problems:
•
Improperly seated or faulty internal component
•
Faulty KVM device
•
Faulty video device
Item
Refer to
1
"POST error messages and beep codes (on page 86)"
2
"Video problems" in the HP ProLiant Servers Troubleshooting Guide
located on the Documentation CD or on the HP website
(http://www.hp.com/support)
3
KVM or iLO 2 documentation
4
"Loose connections (on page 74)"
5
"Symptom information (on page 73)"
6
Server maintenance and service guide, located on the Documentation
CD or the HP website (http://www.hp.com/products/servers/platforms)
7
"Port 85 and iLO messages" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
8
"General memory problems are occurring" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
9
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
•
"Server information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
"Operating system information you need" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
10
Troubleshooting 81
OS boot problems flowchart
Symptoms:
•
Server does not boot a previously installed operating system
•
Server does not boot SmartStart
Possible causes:
•
Corrupted operating system
•
Hard drive subsystem problem
•
Incorrect boot order setting in RBSU
Troubleshooting 82
Item
Refer to
1
HP ROM-Based Setup Utility User Guide
(http://www.hp.com/servers/smartstart)
2
"POST problems flowchart (on page 81)"
3
•
"Hard drive problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Controller documentation
4
"HP Insight Diagnostics (on page 67)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
5
•
"CD-ROM and DVD drive problems" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
Controller documentation
•
"Loose connections (on page 74)"
6
"General memory problems are occurring" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
7
•
"Operating system problems" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
"HP contact information (on page 97)"
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
8
9
"General diagnosis flowchart (on page 76)"
Troubleshooting 83
Server fault indications flowchart
Symptoms:
•
Server boots, but a fault event is reported by Insight Management Agents (on page 65)
•
Server boots, but the internal health LED, external health LED, or component health LED is red or
amber
Troubleshooting 84
NOTE: For the location of server LEDs and information on their statuses, refer to the server
documentation.
Possible causes:
•
Improperly seated or faulty internal or external component
•
Unsupported component installed
•
Redundancy failure
•
System overtemperature condition
Item
Refer to
1
"Management agents (on page 65)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
2
•
"Integrated Management Log (on page 68)" or in the HP ProLiant
Servers Troubleshooting Guide located on the Documentation CD or
on the HP website (http://www.hp.com/support)
•
"Event list error messages" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
3
"Component identification (on page 7)"
4
System Management Homepage (https://localhost:2381)
5
"Power-on problems flowchart ("Server power-on problems flowchart" on
page 78)"
6
•
"Smart Array SCSI Diagnosis feature" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the
HP website (http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
•
"HP contact information (on page 97)"
7
"HP Insight Diagnostics (on page 67)" or in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP
website (http://www.hp.com/support)
8
•
"Hardware problems" in the HP ProLiant Servers Troubleshooting
Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support)
•
Server maintenance and service guide, located on the Documentation
CD or the HP website
(http://www.hp.com/products/servers/platforms)
Troubleshooting 85
POST error messages and beep codes
For a complete listing of error messages, refer to the "POST error messages" in the HP ProLiant Servers
Troubleshooting Guide located on the Documentation CD or on the HP website
(http://www.hp.com/support).
WARNING: To avoid potential problems, ALWAYS read the warnings and cautionary
information in the server documentation before removing, replacing, reseating, or modifying
system components
Troubleshooting 86
Battery replacement
If the server no longer automatically displays the correct date and time, you may need to replace the
battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years.
WARNING: The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
• Do not attempt to recharge the battery.
• Do not expose the battery to temperatures higher than 60°C (140°F).
• Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
• Replace only with the spare designated for this product.
To remove the component:
1.
Power down the server (on page 21).
2.
Extend the server from the rack, if applicable ("Extend the server from the rack" on page 21).
3.
Remove the access panel (on page 22).
4.
Remove any hardware that will interfere with accessing the battery.
5.
Remove the battery.
To replace the component, reverse the removal procedure.
For more information about battery replacement or proper disposal, contact an authorized reseller or an
authorized service provider.
Battery replacement 87
Regulatory compliance notices
Federal Communications Commission notice
Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio
Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic
devices, including computers, generate RF energy incidental to their intended function and are, therefore,
covered by these rules. These rules place computers and related peripheral devices into two classes, A
and B, depending upon their intended installation. Class A devices are those that may reasonably be
expected to be installed in a business or commercial environment. Class B devices are those that may
reasonably be expected to be installed in a residential environment (for example, personal computers).
The FCC requires devices in both classes to bear a label indicating the interference potential of the device
as well as additional operating instructions for the user.
FCC rating label
The FCC rating label on the device shows the classification (A or B) of the equipment. Class B devices
have an FCC logo or ID on the label. Class A devices do not have an FCC logo or ID on the label. After
you determine the class of the device, refer to the corresponding statement.
Class A equipment
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to correct
the interference at personal expense.
Class B equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
Regulatory compliance notices
88
•
Connect the equipment into an outlet on a circuit that is different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio or television technician for help.
Declaration of conformity for products marked with
the FCC logo, United States only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For questions regarding this product, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
•
1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded
or monitored.)
For questions regarding this FCC declaration, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
•
1­281-514-3333
To identify this product, refer to the part, series, or model number found on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the
equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in
order to maintain compliance with FCC Rules and Regulations.
Canadian notice (Avis Canadien)
Class A equipment
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Class B equipment
Regulatory compliance notices
89
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
European Union regulatory notice
This product complies with the following EU Directives:
•
Low Voltage Directive 2006/95/EC
•
EMC Directive 2004/108/EC
Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this
product or product family.
This compliance is indicated by the following conformity marking placed on the product:
This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g. Bluetooth).
This marking is valid for EU non-harmonized Telecom products.
*Notified body number (used only if applicable—refer to the product label)
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany
Disposal of waste equipment by users in private
households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
Regulatory compliance notices
90
Japanese notice
BSMI notice
Korean notice
Class A equipment
Class B equipment
Regulatory compliance notices
91
Laser compliance
This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic
transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Product in
accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser
radiation.
Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser
Notice No. 50, dated May 27, 2001; and with IEC 60825-1:1993/A2:2001.
WARNING: Use of controls or adjustments or performance of procedures other than those
specified herein or in the laser product's installation guide may result in hazardous radiation
exposure. To reduce the risk of exposure to hazardous radiation:
• Do not try to open the module enclosure. There are no user-serviceable components inside.
• Do not operate controls, make adjustments, or perform procedures to the laser device other
than those specified herein.
• Allow only HP Authorized Service technicians to repair the unit.
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration
implemented regulations for laser products on August 2, 1976. These regulations apply to laser products
manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States.
Battery replacement notice
WARNING: The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
• Do not attempt to recharge the battery.
• Do not expose the battery to temperatures higher than 60°C (140°F).
• Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Batteries, battery packs, and accumulators should not be disposed of together with the general
household waste. To forward them to recycling or proper disposal, use the public collection system
or return them to HP, an authorized HP Partner, or their agents.
For more information about battery replacement or proper disposal, contact an authorized reseller or an
authorized service provider.
Taiwan battery recycling notice
The Taiwan EPA requires dry battery manufacturing or importing firms in accordance with Article 15 of
the Waste Disposal Act to indicate the recovery marks on the batteries used in sales, giveaway or
promotion. Contact a qualified Taiwanese recycler for proper battery disposal.
Regulatory compliance notices
92
Power cord statement for Japan
Regulatory compliance notices
93
Electrostatic discharge
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the
system or handling parts. A discharge of static electricity from a finger or other conductor may damage
system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the
device.
To prevent electrostatic damage:
•
Avoid hand contact by transporting and storing products in static-safe containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
•
Place parts on a grounded surface before removing them from their containers.
•
Avoid touching pins, leads, or circuitry.
•
Always be properly grounded when touching a static-sensitive component or assembly.
Grounding methods to prevent electrostatic
discharge
Several methods are used for grounding. Use one or more of the following methods when handling or
installing electrostatic-sensitive parts:
•
Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist
straps are flexible straps with a minimum of 1 megohm ±10 percent resistance in the ground cords.
To provide proper ground, wear the strap snug against the skin.
•
Use heel straps, toe straps, or boot straps at standing workstations. Wear the straps on both feet
when standing on conductive floors or dissipating floor mats.
•
Use conductive field service tools.
•
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, have an authorized reseller
install the part.
For more information on static electricity or assistance with product installation, contact an authorized
reseller.
Electrostatic discharge 94
Specifications
Environmental specifications
Specification
Value
Temperature range*
Operating
10°C to 35°C (50°F to 95°F)
Shipping
-30°C to 50°C (-22°F to 122°F)
Storage
-30°C to 60°C (-22°F to 140°F)
Maximum wet bulb
temperature
28°C (82.4°F)
Relative humidity
(noncondensing)**
Operating
10% to 90%
Non-operating
5% to 95%
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to
3048 m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude maximum for
storage corresponds to a pressure minimum of 70 KPa.
Server specifications
Specification
Value
Dimensions
Height
8.59 cm (3.38 in)
Depth
66.07 cm (26.01 in)
Width
44.54 cm (17.54 in)
Weight (maximum)
27.22 kg (60 lb)
Weight (no drives installed)
20.41 kg (47.18 lb)
Input requirements
Rated input voltage
100 to 132 VAC, 200 to
240 VAC
Rated input frequency
50 Hz to 60 Hz
Rated input current
10 A at 100 VAC
4.9 A at 200 VAC
Rated input power
980 W at 100V AC input
960 W at 200V AC input
Specifications
95
BTUs per hour
3344 at 100V to 120V AC
input
3277 at 200V to 240V AC
input
Power supply output
Rated steady-state power
800 W at 100V AC input
850 W at 120V AC input
1000 W at 200V to 240V AC
input
Maximum peak power
800 W at 100V AC input
850 W at 120V AC input
1000 W at 200V to 240V AC
input
Specifications
96
Technical support
Before you contact HP
Be sure to have the following information available before you call HP:
•
Technical support registration number (if applicable)
•
Product serial number
•
Product model name and number
•
Product identification number
•
Applicable error messages
•
Add-on boards or hardware
•
Third-party hardware or software
•
Operating system type and revision level
HP contact information
For the name of the nearest HP authorized reseller:
•
In the United States, see the HP US service locator webpage (http://www.hp.com/service_locator).
•
In other locations, see the Contact HP worldwide (in English) webpage
(http://welcome.hp.com/country/us/en/wwcontact.html).
For HP technical support:
•
•
In the United States, for contact options see the Contact HP United States webpage
(http://welcome.hp.com/country/us/en/contact_us.html). To contact HP by phone:
o
Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a
week. For continuous quality improvement, calls may be recorded or monitored.
o
If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more
information about Care Packs, refer to the HP website (http://www.hp.com).
In other locations, see the Contact HP worldwide (in English) webpage
(http://welcome.hp.com/country/us/en/wwcontact.html).
Customer Self Repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow
for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP
service providers or service partners) identifies that the repair can be accomplished by the use of a CSR
part, HP will ship that part directly to you for replacement. There are two categories of CSR parts:
Technical support 97
•
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
•
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified as
"No" in the Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography
permits. If assistance is required, you can call the HP Technical Support Center and a technician will help
you over the telephone. HP specifies in the materials shipped with a replacement CSR part whether a
defective part must be returned to HP. In cases where it is required to return the defective part to HP, you
must ship the defective part back to HP within a defined period of time, normally five (5) business days.
The defective part must be returned with the associated documentation in the provided shipping material.
Failure to return the defective part may result in HP billing you for the replacement. With a customer self
repair, HP will pay all shipping and part return costs and determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider. For
the North American program, refer to the HP website (http://www.hp.com/go/selfrepair).
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client)
afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant
la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut
être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux catégories de pièces
CSR:
•
Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à
HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront
facturés.
•
Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le Catalogue
illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre
situation géographique. Si votre situation géographique le permet et que vous demandez une livraison le
jour même ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une assistance
téléphonique, appelez le Centre d'assistance technique HP. Dans les documents envoyés avec la pièce de
rechange CSR, HP précise s'il est nécessaire de lui retourner la pièce défectueuse. Si c'est le cas, vous
devez le faire dans le délai indiqué, généralement cinq (5) jours ouvrés. La pièce et sa documentation
doivent être retournées dans l'emballage fourni. Si vous ne retournez pas la pièce défectueuse, HP se
réserve le droit de vous facturer les coûts de remplacement. Dans le cas d'une pièce CSR, HP supporte
Technical support 98
l'ensemble des frais d'expédition et de retour, et détermine la société de courses ou le transporteur à
utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus
d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
(http://www.hp.com/go/selfrepair).
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente
dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di
assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente
al cliente per la sostituzione. Vi sono due categorie di parti CSR:
•
Obbligatorie – Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida
la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
•
Opzionali – Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di
componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare
la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti
sono identificate da un "No" nel Catalogo illustrato dei componenti.
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il
giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un
supplemento di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica di
un addetto del centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR, HP
specifica se il cliente deve restituire dei componenti. Qualora sia richiesta la resa ad HP del componente
difettoso, lo si deve spedire ad HP entro un determinato periodo di tempo, generalmente cinque (5) giorni
lavorativi. Il componente difettoso deve essere restituito con la documentazione associata nell'imballo di
spedizione fornito. La mancata restituzione del componente può comportare la fatturazione del ricambio
da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene tutte le spese di spedizione e
resa e sceglie il corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
programma in Nord America fare riferimento al sito Web HP (http://www.hp.com/go/selfrepair).
Customer Self Repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und
höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP
Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden
kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien
unterteilt:
•
Zwingend – Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist. Wenn Sie
den Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten
für diesen Service berechnet.
•
Optional – Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für
Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen
Technical support 99
lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog
sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag
geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen
einen Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support Center
anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSRErsatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden
muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines
vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen. Das defekte Teil muss
mit der zugehörigen Dokumentation in der Verpackung zurückgeschickt werden, die im Lieferumfang
enthalten ist. Wenn Sie das defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung
stellen. Im Falle von Customer Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf
und bestimmt den Kurier-/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem Servicepartner
vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP Website unter
(http://www.hp.com/go/selfrepair).
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer
Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de
realizar sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico, HP (o los
proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a cabo mediante el
uso de un componente CSR, HP le enviará dicho componente directamente para que realice su
sustitución. Los componentes CSR se clasifican en dos categorías:
•
Obligatorio: componentes para los que la reparación por parte del usuario es obligatoria. Si
solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los
gastos de desplazamiento y de mano de obra de dicho servicio.
•
Opcional: componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo,
si precisa que HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del
tipo de servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para
que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la palabra
"No" en el catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que lleguen a
su destino al siguiente día laborable. Si la situación geográfica lo permite, se puede solicitar la entrega
en el mismo día o en cuatro horas con un coste adicional. Si precisa asistencia técnica, puede llamar al
Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de un técnico. Con el envío de
materiales para la sustitución de componentes CSR, HP especificará si los componentes defectuosos
deberán devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP,
deberá hacerlo en el periodo de tiempo especificado, normalmente cinco días laborables. Los
componentes defectuosos deberán devolverse con toda la documentación relacionada y con el embalaje
Technical support 100
de envío. Si no enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En
el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío
y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase
en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica,
visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Customer Self Repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een
minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze
onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP Service Partner)
bij de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSR-onderdeel, verzendt HP
dat onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee kunt vervangen. Er zijn twee
categorieën CSR-onderdelen:
•
Verplicht: Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening
gebracht.
•
Optioneel: Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te
vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type
garantieservice voor het product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op de
eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten worden
aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een HP Service
Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de documentatie bij het
vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden geretourneerd. Als het defecte
onderdeel aan HP moet worden teruggezonden, moet u het defecte onderdeel binnen een bepaalde
periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het defecte onderdeel moet met de
bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal. Als u het
defecte onderdeel niet terugzendt, kan HP u voor het vervangende onderdeel kosten in rekening brengen.
Bij reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde
onderdeel en kiest HP zelf welke koerier/transportonderneming hiervoor wordt gebruikt.
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma
van HP. Informatie over Service Partners vindt u op de HP website
(http://www.hp.nl/services/servicepartners).
Reparo feito pelo cliente
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o
reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao
cliente. Existem duas categorias de peças CSR:
Technical support 101
•
Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
•
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas
para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a
cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão
identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil após
o pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro horas pode
ser feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o Centro de suporte
técnico da HP para que um técnico o ajude por telefone. A HP especifica nos materiais fornecidos com a
peça CSR de reposição se a peça com defeito deve ser devolvida à HP. Nos casos em que isso for
necessário, é preciso enviar a peça com defeito à HP dentro do período determinado, normalmente
cinco (5) dias úteis. A peça com defeito deve ser enviada com a documentação correspondente no
material de transporte fornecido. Caso não o faça, a HP poderá cobrar a reposição. Para as peças de
reparo feito pelo cliente, a HP paga todas as despesas de transporte e de devolução da peça e
determina a transportadora/serviço postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato com
o fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
(http://www.hp.com/go/selfrepair).
Technical support 102
Technical support 103
Technical support 104
Acronyms and abbreviations
ABEND
abnormal end
ACU
Array Configuration Utility
AMP
Advanced Memory Protection
ASR
Automatic Server Recovery
BBWC
battery-backed write cache
BIOS
Basic Input/Output System
CSA
Canadian Standards Association
CSR
Customer Self Repair
DDR
double data rate
DIMM
dual inline memory module
ECC
error checking and correcting
HTTP
hypertext transfer protocol
Acronyms and abbreviations 105
IDE
integrated device electronics
IEC
International Electrotechnical Commission
iLO
Integrated Lights-Out
IML
Integrated Management Log
ISEE
Instant Support Enterprise Edition
LED
light-emitting diode
NFPA
National Fire Protection Association
NIC
network interface controller
NMI
non-maskable interrupt
NVRAM
non-volatile memory
ORCA
Option ROM Configuration for Arrays
OS
operating system
PCI
peripheral component interface
PCI Express
Peripheral Component Interconnect Express
Acronyms and abbreviations 106
PCI-X
peripheral component interconnect extended
PCIe
peripheral component interconnect express
POST
Power-On Self Test
PPM
processor power module
PSP
ProLiant Support Pack
RBSU
ROM-Based Setup Utility
RDP
Rapid Deployment Pack
ROM
read-only memory
SAS
serial attached SCSI
SDRAM
synchronous dynamic RAM
SFF
small form-factor
SIM
Systems Insight Manager
SMTP
Simple Mail Transfer Protocol
SNMP
Simple Network Management Protocol
Acronyms and abbreviations 107
TMRA
recommended ambient operating temperature
UID
unit identification
UPS
uninterruptible power system
USB
universal serial bus
VCA
Version Control Agent
Acronyms and abbreviations 108
Index
A
access panel 22, 23
ACU (Array Configuration Utility) 61
additional information 71
ADU (Array Diagnostic Utility) 68
Advanced ECC memory 43
air baffle 23, 24
airflow requirements 30
Altiris eXpress Deployment Server 62
Array Configuration Utility (ACU) 61
Array Diagnostic Utility (ADU) 68
authorized reseller 97
auto-configuration process 60
Automatic Server Recovery (ASR) 63
Autorun menu 59
B
batteries, replacing 92
battery 14, 87, 92
battery cabling for BBWC 56
battery pack LEDs 18
battery replacement notice 92
battery-backed write cache (BBWC) 18
beep codes 86
BIOS Serial Console 61
BIOS upgrade 63
blue screen event 14
boot options 61
BSMI notice 91
buttons 7, 11
C
cable management arm 27, 32, 33
cables 55, 74, 89
cabling 55, 56, 57, 58
cabling, BBWC 55, 56
cabling, fan board 56
cabling, hard drive backplane 57
cabling, hot-plug SAS hard drive 55
cabling, media drive bay 58
cabling, Systems Insight Display 57
Canadian notice 89
Care Pack 29, 70
cautions 72
CD-ROM drive 47
class A equipment 88
class B equipment 88
CMOS 13
component identification 7, 14
components 7
configuration of system 35, 59
Configuration Replication Utility 60
configuration tools 59
connection problems 74
connectors 7
contact information 97
contacting HP 97
crash dump analysis 14
creating a disk image 62
CSR (customer self repair) 97
customer self repair (CSR) 97
D
DC power supply 48
Declaration of Conformity 89
deployment software 62
device numbers 16
diagnosing problems 71, 74
diagnostic tools 59, 62, 63, 67
diagnostics utility 67
DIMM banks, population 43
DIMM installation guidelines 43
DIMM slot locations 13
DIMMs 13, 43
DIMMs, installation 43
diskette drive 47
diskette image creation 62
drive LEDs 16, 17
drivers 69
DVD/CD-ROM drive, removing 47
E
electrical grounding requirements 31
electrostatic discharge 94
environmental requirements 30
Index 109
Erase Utility 64
error messages 86
European Union notice 90
expansion board 51, 52
expansion slot covers 51
expansion slots 10
external health LED 7
external option blank 33
F
fan board 20
fan board connector 20
fan configurations 20
fan module locations 20
fan operation 28
FCC rating label 88
features 7
Federal Communications Commission (FCC)
notice 88, 89
flowcharts 75, 76, 78, 81, 82, 84
front panel components 7
I
iLO (Integrated Lights-Out) 64
iLO 2 (Integrated Lights-Out 2) 64
iLO 2 activity LED 11
iLO 2 connector 10
iLO 2 link LED 10
IML (Integrated Management Log) 68
Important Safety Information document 71
Insight Diagnostics 67
installation services 29
installation, server options 33, 37
installing hardware 37
installing operating system 35
installing server 33
installing the access panel 23
Instant Support Enterprise Edition 68
Integrated Lights-Out (iLO) 64
internal health LED 7, 14
internal USB functionality 67
J
G
Japanese notice 91
general diagnosis flowchart 76
grounding methods 94
grounding requirements 31
K
H
hard drive backplane 57
hard drive backplane power cabling 57
hard drive bays 7
hard drive LEDs 16, 17
hard drives 17
hard drives, determining status of 17
hard drives, installing 44
hardware options 37
hardware options installation 33, 37
health driver 28, 63
health LEDs 14
help resources 97
hot-plug fans 20, 27
hot-plug power supply 47
HP Insight Diagnostics 67
HP Instant Support Enterprise Edition 68
HP ProLiant Essentials Foundation Pack 65
HP ProLiant Essentials Rapid Deployment Pack 62
HP Systems Insight Manager, overview 65
HP technical support 97
HP, contacting 97
keyboard connector 10
Korean notices 91
L
laser compliance 92
laser devices 92
LED, external health 7
LED, iLO 2 activity 11
LED, iLO 2 link 11
LED, internal health 7
LED, PCI riser cage 17
LED, system power 7
LEDs 7
LEDs, battery pack 18
LEDs, drive 16, 17
LEDs, front panel 7
LEDs, hard drive 16, 17
LEDs, NIC 11
LEDs, power supply 11
LEDs, rear panel 11
LEDs, SAS hard drive 17
LEDs, SATA hard drive 17
LEDs, troubleshooting 71
LEDs, unit identification (UID) 11
Index 110
loose connections 74
M
Management Agents 65
management tools 63
media drive 47
media drive bay cabling 58
media drive blank 47
memory 42, 43
memory dump 14
memory, Advanced ECC 43
modifications, FCC notice 89
mouse connector 10
N
NIC connectors 10
NIC LEDs 11
NMI functionality 14
NMI jumper 14
NMI switch 14
NVRAM, clearing 13
O
Online ROM Flash Component Utility 63
Open Services Event Manager 69
operating system crash 14
operating systems 35, 69
operations 21
optimum environment 30
Option ROM Configuration for Arrays (ORCA) 62
options installation 33, 37
ORCA (Option ROM Configuration for Arrays) 62
OS boot problems flowchart 82
P
PCI expansion slot definitions 10
PCI riser board 53
PCI riser board expansion slot definitions 11
PCI riser cage 25
PCI riser cage LED 17
PCI slots 11
PDU (power distribution unit) 31
phone numbers 97
POST error messages 86
POST problems flowchart 81
power cord 72, 93
power cord anchor 33
power cord connector 10
power distribution unit (PDU) 31
Power On/Standby button 21, 35
power requirements 31
power supplies 10, 11, 47
power supply LEDs 11
powering down 21
powering up 21, 60
preparation procedures 74
problem diagnosis 71
processor 37
processor socket 37
ProLiant Support Pack (PSP) 69
PSPs, overview 69
Q
quick release levers 7, 21
R
rack installation 29
rack mounting hardware 32
rack resources 29
rack stability 72
rack warnings 32, 72
rack, extending server from 21
RBSU (ROM-Based Setup Utility) 60
RBSU configuration 60
rear components 10
rear panel connectors 10
rear panel LEDs 11
rear panel, accessing 27
recommended ambient operating temperature
(TMRA) 30
redundant ROM 65
registering the server 36
regulatory compliance notices 88, 90, 92
remote support and analysis tools 68, 69
removing the access panel 22
required information 97
requirements, airflow 30
requirements, electrical grounding 31
requirements, environmental 30
requirements, power 31
requirements, space 30
requirements, temperature 30
resetting the system 14
ROM redundancy 65
ROM, updating 63
ROM-Based Setup Utility (RBSU) 60
ROMPaq utility 63, 65
Index 111
S
T
safety considerations 71
safety information 65
SAS drive numbers 17
SAS drives 17, 44
SAS hard drive 44, 45, 46
SAS hard drive LEDs 16, 17
SATA hard drive 17
SATA hard drive LEDs 16, 17
scripted installation 59
serial connector 10
serial number 62
server features and options 37
server options, installing 33, 37
server specifications 95
server, installation 33
service notifications 75
Setup 29
shipping carton contents 32
site requirements 30
SmartStart autorun menu 59
SmartStart Scripting Toolkit 59
SmartStart, overview 59
space requirements 30
specifications, environmental 95
specifications, server 95
start diagnosis flowchart 75
static electricity 94
status lights, battery pack 18
StorageWorks Library and Tape Tools (L&TT) 64
support 68, 97
support packs 59
supported operating systems 69
switch, NMI 14
switches 13, 14
symbols on equipment 72
system board 12
system board battery 92
system board components 12
system configuration settings 59
System Erase Utility 64
system maintenance switch 13, 14
system power LED 7, 18
system, keeping current 69
Systems Insight Display 7, 9
Systems Insight Display cabling 57
Systems Insight Display LEDs and internal health LED
combinations 14
Systems Insight Manager 65
Taiwan battery recycling notice 92
technical support 97
telephone numbers 97
temperature requirements 30
TMRA (recommended ambient operating
temperature) 30
Torx screwdriver 10
troubleshooting 71
troubleshooting resources 71
U
UID LED 7, 11, 14
updating the system ROM 65
UPS (uninterruptible power supply) 31
USB connectors 7, 10
USB support 66
utilities 59
utilities, deployment 59, 60, 62
V
ventilation 30
video connector 7, 10
W
warnings 32, 72
Web-Based Enterprise Service 68
Index 112