Bosch PLE?2CS Plena Technical data

Plena Two-zone Call Station
Installation and User Instructions
en
PLE-2CS
Plena Two-zone Call Station | Installation and User Instructions | Important safeguards
Important safeguards
Before installing or operating this product, always read
the Safety Instructions, which are available as a separate
document (9922 141 7014x). These instructions are
supplied together with all equipment that can be
connected to the mains.
Thank you for choosing a Bosch Security Systems
product!
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 2
Plena Two-zone Call Station | Installation and User Instructions | Table of contents
en | 3
Table of contents
Important safeguards ...................................................................................................................................................2
Table of contents ...........................................................................................................................................................3
1. Introduction ....................................................................................................................................................................5
1.1 Purpose .....................................................................................................................................................................................5
1.2 Digital document .....................................................................................................................................................................5
1.3 Intended audience ..................................................................................................................................................................5
1.4 Related documentation ..........................................................................................................................................................5
1.5 Alerts ..........................................................................................................................................................................................5
1.6 Icons ...........................................................................................................................................................................................5
1.6.1 Note icons ...........................................................................................................................................................................5
1.6.2 Caution, Warning, and Danger icons ...........................................................................................................................5
1.7 Conversion tables ...................................................................................................................................................................6
2. Description .....................................................................................................................................................................7
2.1 The Plena product range .......................................................................................................................................................7
2.2 Contents of box .......................................................................................................................................................................7
2.3 The Plena Two-zone Call Station ........................................................................................................................................7
2.3.1 Balanced line level output ...............................................................................................................................................7
2.3.2 Loop-through RJ-45 sockets ..........................................................................................................................................7
2.3.3 DIP switches and status LEDs .......................................................................................................................................7
2.3.4 PTT button ...........................................................................................................................................................................7
2.4 Controls, connectors and indicators ..................................................................................................................................8
2.4.1 Top side ...............................................................................................................................................................................8
2.4.2 Bottom side .........................................................................................................................................................................8
3. Installation ......................................................................................................................................................................9
3.1 Unpack unit ...............................................................................................................................................................................9
3.2 Connect unit to PLE-series two-zone mixer (amplifier) ...................................................................................................9
3.3 Make configuration settings ..................................................................................................................................................9
4. Connections and settings ........................................................................................................................................ 11
4.1 Connecting multiple call stations ..................................................................................................................................... 11
4.2 Configuration settings ......................................................................................................................................................... 11
4.2.1 Chime settings ................................................................................................................................................................ 11
4.2.2 Momentary or latching speaking setting ................................................................................................................... 11
4.2.3 Speech filter setting ....................................................................................................................................................... 11
4.2.4 Microphone gain settings ............................................................................................................................................. 12
5. Operation ..................................................................................................................................................................... 13
5.1 Make calls (momentary speaking function) .................................................................................................................... 13
5.2 Make calls (latching speaking function) .......................................................................................................................... 13
5.3 Adjust the call station output volume ............................................................................................................................... 13
6. Technical data ............................................................................................................................................................. 15
6.1 Electrical ................................................................................................................................................................................. 15
6.2 Performance .......................................................................................................................................................................... 15
6.3 Interconnection ..................................................................................................................................................................... 15
6.4 Mechanical ............................................................................................................................................................................. 15
6.5 Environmental conditions ................................................................................................................................................... 15
6.6 Certifications and Approvals ............................................................................................................................................. 15
Bosch Security Systems | 2008-01 | PLE-2CS en
Plena Two-zone Call Station | Installation and User Instructions | Table of contents
Intentionally left blank
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 4
Plena Two-zone Call Station | Installation and User Instructions | Introduction
1
Introduction
1.1
Purpose
The purpose of these Installation and User Instructions
is to provide information that is required to install,
configure and operate a Plena Two-zone Call Station.
1.2
1.6
Icons
1.6.1
Note icons
The icons used in combination with Notes provide extra
information about the Note. See the following
examples:
Digital document
Note
General icon for notes.
These Installation and User Instructions are also
available as a digital document in the Adobe Portable
Document Format (PDF). All references to pages,
figures, tables, etc. in this digital document contain
hyperlinks to the referenced location.
1.3
Related documentation
Safety Instructions (9922 141 ****).
1.5
Note
Consult the indicated source of information.
Intended audience
These Installation and User Instructions are intended
for installers and users of a Plena Two-zone Call Station.
1.4
en | 5
1.6.2
Caution, Warning, and Danger
icons
The icons used in combination with Caution, Warnings,
and Dangers indicate the type of hazard present. See the
following examples:
Alerts
Four types of alerts are used in this manual. The alert
type is closely related to the effect that may be caused if
it is not observed. These alerts - from least severe effect
to most severe effect - are:
• Note
Alert containing additional information. Usually, not
observing a note alert does not result in damage to
the equipment or personal injuries.
• Caution
The equipment can be damaged if the alert is not
observed.
• Warning
Persons can be (severely) injured, or the equipment
can be seriously damaged, if the alert is not
observed.
• Danger
Not observing the alert can result in death.
Bosch Security Systems | 2008-01 | PLE-2CS en
Caution, Warning, Danger
General icon for Cautions, Warnings and
Dangers.
Caution, Warning, Danger
Icon for risk of electric shock.
Caution, Warning, Danger
Icon for risk of electrostatic discharge.
Plena Two-zone Call Station | Installation and User Instructions | Introduction
1.7
Conversion tables
In this manual, SI units are used to express lengths,
masses, temperatures etc. These can be converted to
non-metric units using the following information.
table 1.1: Conversion of units of length
1 in =
25.4 mm
1 mm =
1 in =
2.54 cm
1 cm =
1 ft =
0.3048 m
1m=
1 mi =
1.609 km
1 km =
0.03937 in
0.3937 in
3.281 ft
0.622 mi
table 1.2: Conversion of units of mass
1 lb =
0.4536 kg
1 kg =
2,2046 lb
table 1.3: Conversion of units of pressure
1 psi =
68.95 hPa
1 hPa =
0.0145 psi
Note
1 hPa = 1 mbar.
table 1.4: Conversion of units of temperature
9
°F = --- ⋅ °C + 32
5
5
°C = --- ⋅ ( °F – 32 )
9
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 6
Plena Two-zone Call Station | Installation and User Instructions | Description
2
Description
2.1
The Plena product range
The Plena Two-zone Call Station is part of the Plena
product range. Plena provides public address solutions
for places where people gather to work, worship, trade,
or relax. It is a family of system elements that are
combined to create public address systems tailored for
virtually any application
The Plena product range includes:
• mixers
• mixer amplifiers
• preamplifiers
• power amplifiers
• a music source unit
• a digital message manager
• a feedback suppressor
• call stations
• an All-in-One system
• a voice alarm system
• a timer
• a charger
• a loop amplifier
The various elements are designed to complement each
other thanks to matched acoustical, electrical and
mechanical specifications.
2.2
Contents of box
The packaging box contains the following:
• PLE-2CS Plena Two-zone Call Station
• Cable terminated with a lockable Cat-5 connector
2.3
The Plena Two-zone Call
Station
The Plena Two-zone Call Station is a modern, highquality call station with a stable metal base design, a
flexible microphone stem and a unidirectional
condenser microphone. It can make calls to selected
zones (zone one or two) in a public address system built
with the PLE-series two-zone mixer and mixer
amplifiers.
In addition to tabletop use, the Plena design allows neat
flush-mounting in desktops.
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 7
The Plena Two-zone Call Station features:
• a selectable microphone gain level, a selectable
speech filter, and a limiter for improved intelligibility
• a balanced line level output. See section 2.3.1.
• two loop-through RJ-45 sockets. See section 2.3.2.
• DIP switches and status LEDs. See section 2.3.3.
• a push-to-talk (PTT) button. See section 2.3.4.
For a detailed description of all controls, connections
and indicators, see section 2.4.
2.3.1
Balanced line level output
The Plena Two-zone Call Station has a balanced line
level output, giving it a maximum range of 200 m from
the controller when using Cat-5 Ethernet cables.
2.3.2
Loop-through RJ-45 sockets
With the loop-through RJ-45 sockets, it is possible to
daisy chain up to six call stations. The priority is
automatic; the call station nearest to the mixer has
priority and can override the call station further away
from the mixer.
2.3.3
DIP switches and status LEDs
With the DIP switches at the base of the call station you
can select different microphone gain levels, seven
different chimes (any .wav file), define the speech filter
and the momentary or latching speaking functions.
Two LEDs on top of the call station show which zones
have been selected. One additional LED gives visible
feedback on the active state of the microphone and the
system:
• green flashing: microphone is standby (chime is
sounding)
• green continuous: microphone is active
• off: a call is being made by a higher priority call
station
2.3.4
PTT button
To the PTT button, a pre- and post chime can be
assigned that is played at the start or at the end of the
call. To this end, the call station is equipped with seven
built-in chimes.
Plena Two-zone Call Station | Installation and User Instructions | Description
2.4
2.4.1
Controls, connectors and
indicators
Top side
See figure 2.1 for an overview of the controls and
indicators on the top side of the call station:
1 Zone selection buttons - Two buttons to select
the zones to which the business call is distributed.
Each button has a green LED, which indicates the
zone to which the business call is distributed.
2 Push-to-talk (PTT) button - A push-to-talk
(PTT) button to start the business call.
3 Status indicator - A LEDs that indicates the status
of the call station. See section 2.3.3.
2.4.2
en | 8
Bottom side
See figure 2.2 for an overview of the controls and
indicators at the bottom of the call station:
1 Configuration settings - A set of DIP switches to
configure the call station (by setting the microphone
gain level, the chime and the speech filter). See
section 4.2.
2 System sockets - Two redundant RJ-45 sockets to
connect the call station to the PLE-series two-zone
mixer or mixer amplifiers using Cat-5 Ethernet
cables. When the system requires more than 2 call
stations, the system sockets can be used to make
loop-throughs. See section 4.1.
3 Rotary volume control - A rotary volume
control (potentiometer) to set the output volume of
the call station. See chapter 5.3.
Plena
2
1
3
3
1 2 3 4 5 6 7 8
figure 2.1: Top view
figure 2.2: Bottom view
Bosch Security Systems | 2008-01 | PLE-2CS en
ON
2
1
Plena Two-zone Call Station | Installation and User Instructions | Installation
3
Installation
3.1
Unpack unit
1 Remove the unit from the box, and discard the
packaging material according to local regulations.
2 Use your fingernails to carefully peel off the
protective plastic film. Do not use sharp or pointed
objects.
3.2
Connect unit to PLE-series
two-zone mixer (amplifier)
1 Connect the Plena Two-zone Call Station to the
PLE-series two-zone mixer or mixer amplifier using
a Cat-5 Ethernet cable (see figure 3.1). Either one of
the RJ-45 sockets can be used.
Ple
na
Ple
na
figure 3.1: Connecting the call station to the mixer or
the mixer amplifier
3.3
Make configuration settings
1 Make the configuration settings (see section 4.2).
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 9
Plena Two-zone Call Station | Installation and User Instructions | Installation
Intentionally left blank
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 10
Plena Two-zone Call Station | Installation and User Instructions | Connections
4
4.1
en | 11
Connections and settings
4.2
Connecting multiple call
stations
Use the DIP switches at the bottom of the call station to
set the chime, the momentary or latching speaking
function, the speech filter and the microphone gain. See
figure 4.2.
When the configuration requires more than one call
station, use the loop-through RJ-45 sockets on the call
stations to make loop-throughs.
Note
In such a daisy chain configuration the priority
is automatic; the call station nearest to the mixer
has priority and can override the call station
further away from the mixer. Call station
number 2 has priority over call station
number 3, etc. See figure 4.1.
4.2.1
Configuration settings
Chime settings
See figure 4.2. DIP switches number 1, 2 and 3 are used
for setting the chime.
1 = ON-position, 0 = OFF-position.
table 4.1: Chime settings
DIP switch setting
Description
(1-2-3)
0-0-0
no chime
0-0-1
1-tone chime
0-1-0
2-tone chime
0-1-1
2-tone chime reversed
1-0-1
3-tone chime A
1-0-0
3-tone chime reversed B
1-1-0
4-tone chime A
1-1-1
4-tone chime C
na
Ple
4.2.2
Momentary or latching speaking
setting
See figure 4.2. DIP switch number 4 is used for setting
the momentary or latching speaking function.
1 = latching, 0 = momentary.
4.2.3
Speech filter setting
Ple
na
na
Ple
Ple
na
See figure 4.2. DIP switch number 5 is used for setting
the speech filter ON (1) of OFF (0).
Ple
na
Ple
na
figure 4.1: Connecting multiple call stations
Bosch Security Systems | 2008-01 | PLE-2CS en
Plena Two-zone Call Station | Installation and User Instructions | Connections
4.2.4
Microphone gain settings
See figure 4.2. DIP switches number 6 and 7 are used
for setting the microphone gain.
1 = ON-position, 0 = OFF-position.
table 4.2: Microphone gain settings
DIP switch setting
Description
(6-7)
0-0
-15 dB
1-0
0 dB
0-1
+6 dB
1-1
+6 dB
1 2 3 4 5 6 7 8
ON
ON(1)
DIP
OFF(0)
1 2 3 4 5 6 7 8 (spare)
figure 4.2: DIP switches
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 12
Plena Two-zone Call Station | Installation and User Instructions | Operation
5
Operation
5.1
Make calls (momentary
speaking function)
1 Press the push-to-talk button and keep the button
depressed during the business call.
2 Make the business call.
3 Release the push-to-talk button after the business
call.
5.2
Make calls (latching speaking
function)
1 Shortly press the push-to-talk button to start the
business call.
2 Make the business call.
3 Shortly press the push-to-talk button to stop the
business call.
5.3
Adjust the call station output
volume
1 Use a screw driver to adjust the output volume of the
call station. Turn clockwise to increase the output
volume or turn counterclockwise to decrease the
output volume. See figure 5.1.
Caution
Be careful not to damage the printed circuit
board located directly underneath the orifice.
Use a small screw driver, preferably a plastic
one.
Bosch Security Systems | 2008-01 | PLE-2CS en
figure 5.1: Adjust the output volume
en | 13
Plena Two-zone Call Station | Installation and User Instructions | Operation
Intentionally left blank
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 14
Plena Two-zone Call Station | Installation and User Instructions | Technical data
6
6.1
Technical data
Electrical
Voltage range:
24 V(DC), supplied by PLE-series mixer or mixer
amplifier.
Current consumption:
< 30 mA
6.2
Performance
Nominal sensitivity:
85 dB SPL (gain preset 0 dB)
Nominal output level:
700 mV
Maximum input sound level:
110 dB SPL
Gain preset:
-15 / 0 / +6 dB
Limiter threshold:
2V
Compression ratio limiter:
1:20
Distortion:
< 0.6% (maximum input)
Equivalent input noise level:
25 dB SPL(A)
Frequency response:
100 Hz - 16 kHz
Speech filter:
- 3 dB @ 315 Hz, high-pass, 6 dB/oct
Output impedance:
200 Ω
6.3
Interconnection
Type:
2x redundant RJ-45 sockets for daisy chaining
multiple call stations.
Bosch Security Systems | 2008-01 | PLE-2CS en
6.4
en | 15
Mechanical
Base dimensions (H x W x D), without
microphone:
40 x 100 x 235 mm (1.57 x 3.97 x 9.25 in)
Stem length (with microphone):
390 mm (15.35 in)
Cat-5 extension cable length:
5 m (16.4 ft)
Weight:
Approx. 1 kg (2.2 lb)
Mounting:
Standalone
Color:
Charcoal with silver
6.5
Environmental conditions
Operating temperature range:
-10 °C to +55 °C (+14 °F to +131 °F)
Storage temperature range:
-40 °C to +70 °C (-40 °F to +158 °F)
Relative humidity:
< 95%
6.6
Certifications and Approvals
Safety:
According to EN 60065
EMC immunity:
According to EN 55103-2
EMC emission:
According to EN 55103-1
Plena Two-zone Call Station | Installation and User Instructions | Technical data
Intentionally left blank
Bosch Security Systems | 2008-01 | PLE-2CS en
en | 16
For more information visit
www.boschsecuritysystems.com
© Bosch Security Systems B.V.
Data subject to change without notice
2008-01 | PLE-2CS en