user manual
Electrolux E:Volution
barbecue
EQBM120HAS, EQBM120LAS,
EQBM75HAS, EQBM75LAS
2 contents electrolux e:volution barbecue
Congratulations
Congratulations and thank you for choosing our Electrolux
E:Volution barbecue. We are sure you will find your new
barbecue a pleasure to use. Before you use the barbecue,
we recommend that you read through the entire user
manual, which provides the description of the barbecue and
its functions.
To avoid the risks that are always present when you use
a gas appliance, it is important that it is installed correctly
and that you read the safety instructions carefully to avoid
misuse and hazards.
We recommend that you keep this instruction booklet for
future reference and pass it on to any future owners.
After unpacking the barbecue please check it is not
damaged. If in doubt, do not use the appliance but contact
your local Electrolux Customer Care Centre.
Contents
• Important safety instructions
• EQBM120HAS description
• EQBM120HAS dimensions
• EQBM120LAS description
• EQBM120LAS dimensions
• EQBM75HAS description
• EQBM75HAS dimensions
• EQBM75LAS description
• EQBM75LAS dimensions
• Barbecue parts
• Assembling the barbecue
• Gas specifications
• Gas bottle safety information
• Installing the gas cylinder
• Leak test procedure
• Conversion to natural gas
• Choosing a location
• Installation warnings
• Activating the wheel brake
• Configuration of hotplates
• Operating instructions
• Using the roasting hood
• Using the side table
• Lid safety leg
• Cleaning and care
• Maintenance
• Troubleshooting
• Warranty
3
4
5
6
7
8
9
10
11
12
13
14
14
15
15
15
17
17
18
18
18
19
20
20
21
22
22
23
environmental tip
Information on disposal for users
• Most of the packing materials are recyclable. Please
dispose of those materials through your local recycling
depot or by placing them in appropriate collection
containers.
• If you wish to discard this product, please contact your
local authorities and ask for the correct method of disposal.
electrolux e:volution barbecue important safety instructions 3
Important safety instructions
Please read the user manual carefully and store in a handy
place for later reference.
Meanings of the symbols used in this manual are shown
below:
warning
This symbol indicates information concerning your
personal safety
warning
IF YOU SMELL GAS, do not attempt to light the
barbecue. Locate the leak and re-tighten the leaking
joint. Carry out the Leak Test procedure as described in
this manual. If the leak persists, turn off the gas supply
and call Electrolux Service or a Licensed Gas Fitter.
warning
Do not lean over barbecue when lighting.
caution
This symbol indicates information on how to avoid
damaging the appliance
tips and information
This symbol indicates tips and information about use
of the appliance
Do not leave the barbecue unattended when alight.
Do not delay lighting once the gas has been turned
on.
Do not store or use aerosol cans in the vicinity of the
barbecue.
Do not store flammable liquids in the vicinity of the
barbecue.
o not use caustic or abrasive based cleaners on the
D
barbecue.
Do not operate the barbecue with the cover on.
environmental tip
This symbol indicates tips and information about
economical and ecological use of the appliance
This symbol indicates never to do this
Do not attempt to dismantle or adjust the control
valves.
Do not attempt to dismantle or adjust the regulator.
Do not test for leaks with a naked flame.
Do not modify the construction of this appliance or
modify the injector orifice size.
Do not obstruct any ventilation of the barbecue.
For your safety please read this book before
operating your barbecue.
warning
Improper installation, adjustment, alteration or
maintenance can cause injury or property damage.
Please contact your nearest Electrolux Service
Department for additional information or assistance
for an approved installer.
NOTE TO THE INSTALLER
THIS MANUAL MUST REMAIN WITH THE OWNER FOR
FUTURE REFERENCE
Do not allow children to operate or play near the
barbecue.
caution
This barbecue is supplied set up for Universal LPG
and is labelled accordingly. A Natural Gas conversion
kit is available for purchase from Electrolux Service
or Spare Parts. Conversion of this unit to Natural Gas
must be carried out by a qualified licensed person
and a Certificate of Compliance must be issued
to the owner on completion of the installation and
conversion.
4 EQBM120HAS description electrolux e:volution barbecue
EQBM120HAS
1
2
3
4
5
6
7
10
8
11
9
11
13
14
12
15
16
1 Roasting hood
10 Ribbed hotplate
2 Temperature indicator
11 Fold down side tables
3 Slimline lid cover
12 Storage compartment
4Burner controls
13 Gas connection point
5 Swivel wheels with brake
14 Gas hose with universal LPG connection
6 Pivoting safety leg
15 Slide-out gas bottle tray
7 Warming racks
16 Match holder for manual lighting (not illustrated)
8 Grill
17Removable oil reservoirs located at front of cooking
surface (not illustrated)
9 Hotplate
18 Flame tamers located under grills (not illustrated)
electrolux e:volution barbecue EQBM120HAS dimensions 5
683
EQBM120HAS dimensions
1200
525
637
922
1126
35
203
363
Dimensions are in millimetres.
6 EQBM120LAS description electrolux e:volution barbecue
EQBM120LAS
1
2
3
4
5
8
6
9
7
9
11
12
10
13
14
1 Slimline lid cover
9 Fold down side tables
2 Slimline lid cover
10 Storage compartment
3Burner controls
11 Gas connection point
4 Swivel wheels with brake
12 Gas hose with universal LPG connection
5 Pivoting safety leg
13 Slide-out gas bottle tray
6 Grill
14 Match holder for manual lighting (not illustrated)
7 Hotplate
15Removable oil reservoirs located at front of cooking
surface (not illustrated)
8 Ribbed hotplate
16 Flame tamers located under grills (not illustrated)
electrolux e:volution barbecue EQBM120LAS dimensions 7
683
EQBM120LAS dimensions
1200
363
532
922
957
35
653
Dimensions are in millimetres.
8 EQBM75HAS description electrolux e:volution barbecue
EQBM75HAS
1
2
3
4
5
7
8
6
8
9
10
11
12
1 Roasting hood
8 Fold down side tables
2 Temperature indicator
9 Gas connection point
3Burner controls
10 Gas hose with universal LPG connection
4 Swivel wheels with brake
11 Slide-out gas bottle tray
5 Warming racks
12 Match holder for manual lighting (not illustrated)
6 Hotplate
13Removable oil reservoirs located at front of cooking
surface (not illustrated)
7 Grills
14 Flame tamers located under grills (not illustrated)
electrolux e:volution barbecue EQBM75HAS dimensions 9
684
EQBM75HAS dimensions
750
525
922
1126
203
637
Dimensions are in millimetres.
10 EQBM75LAS description electrolux e:volution barbecue
EQBM75LAS
1
2
3
5
6
4
6
7
8
9
10
1 Slimline lid
7 Gas connection point
2Burner controls
8 Gas hose with universal LPG connection
3 Swivel wheels with brake
9 Slide-out gas bottle tray
4 Hotplate
10 Match holder for manual lighting (not illustrated)
5 Grills
11Removable oil reservoirs located at front of cooking
surface (not illustrated)
6 Fold down side tables
12 Flame tamers located under grills (not illustrated)
electrolux e:volution barbecue EQBM75LAS dimensions 11
684
EQBM75LAS dimensions
750
532
922
957
35
653
Dimensions are in millimetres.
12 barbecue parts electrolux e:volution barbecue
120cm barbecue parts
75cm barbecue parts
Contents of your 120cm barbecue pack:
Contents of your 75cm barbecue pack:
description
EQBM12AS –
120cm mobile
barbecue base
qty
description
1
EQBM75AS –
75cm mobile
barbecue base
1
EQB6HAS –
Roasting hood and
warming racks
OR
OR
qty
1
1
EQB6HAS –
Roasting hood and
warming racks
OR
OR
EQB6LAS –
Flat lid with
mounting brackets
EQB6LAS –
Flat lid with
mounting brackets
EQB3LAS –
1
Small flat lid with
mounting brackets
Grills
2
Grills
2
Hotplate
1
Hotplate
1
Flame tamers
2
Ribbed hotplate
1
Flame tamers
2
1 plastic bag containing this instruction book and trim fixing
screws
1 plastic bag containing this instruction book and trim fixing
screws
Tools you will need for assembly:
– Phillips head screwdriver
electrolux e:volution barbecue assembling the barbecue 13
Assembling the barbecue
1.Remove packaging & remove all components from
inside of burner box. Remove cooking plates fastened
to pallet under cabinet.
2.Unfasten bolts securing unit to the pallet base and
remove unit from base.
model EQBM12AS
3. F
itting of roasting hood
– Unpack the roasting hood.
– Remove necessary screws to enable assembly of hood.
Some screws have been removed to facilitate assembly
and are included in bag with instruction manual.
– Due to the size of the roasting hood, it is
recommended that two people place the roasting
hood into position.
– When fitting the roasting hood assembly, take
particular care to avoid scratching of the external trim.
– Once in position, fix hood assembly to trim surround
with screws provided.
polystyrene
pallet bolt.
unscrew to release from pallet
cooking plates.
cut strap at rear to remove
polystyrene.
remove by lifting barbecue to release
OR
Fitting of slimline lid
– Unpack the slimline lid.
– Remove necessary screws from barbecue trim
surround to enable assembly of brackets.
– Fit brackets to trim surround with screws removed
and additional screws in plastic bag. Fit additional
screws provided to trim where missing.
– Fit lid to brackets.
model EQBM75AS
bracket orientation for flat lid
polystyrene
pallet bolt.
unscrew to release from pallet
polystyrene.
remove by lifting barbecue to release
cooking plates.
cut strap at rear to remove
4.Fit small slimline lid (if required) in the same manner as
larger lid above.
continued over
14 assembling the barbecue / gas specifications / gas bottle safety information electrolux e:volution barbecue
Assembling the barbecue (cont.)
Gas specifications
5.Position flame tamers into desired locations (under
where grill sections will be fitted) and fix back edge of
flame tamer into rear of barbecue body.
For 120cm barbecue
model
gas type
EQBM120HAS & EQBM120LAS
universal LPG
Maximum gas consumption 50 MJ/h
natural gas
57.5 MJ/h
Injector orifice diameter (mm) 0.90
1.50
Number of injectors
5
5
Regulator pressure
2.75 kPa
1.00 kPa*
For 75cm barbecue
model
gas type
6.Place hotplate and grill sections into desired positions
ensuring that the flame tamers are under grill sections.
NOTE: ensure that grill assemblies are orientated
correctly so that the surface of the grill is sloping
forward to allow oil to drain into oil reservoirs.
EQBM75HAS & EQBM75LAS
universal LPG
Maximum gas consumption 40 MJ/h
natural gas
46 MJ/h
Injector orifice diameter (mm) 0.90
1.50
Number of injectors
4
4
Regulator pressure
2.75 kPa
1.00 kPa*
Notes
• This appliance MUST be serviced only by a qualified
licensed person.
•This product is intended for outdoor use only.
•Ventilation holes in the unit must not be obscured by
the installation.
*The outlet pressure at the Natual Gas regulator will be
lower when all burners are operating. Burner pressure
should read 1.0kPa with one burner operating and
approximately 0.93kPa with four burners operating.
7.Fit warming racks to splashguard at rear (roasting hood
models only).
For conversion to Natural Gas a conversion kit will need to
be purchased from Electrolux Spare Parts.
Gas bottle safety information
• This appliance is designed to use a Universal LPG 9kg
(20 lbs) gas cylinder.
•The gas cylinder must be made and marked in
accordance with specifications for LPG cylinders
•The isolation valve must be turned off when the
appliance is not in use.
•Gas cylinders must be stored in an approved housing
out of reach of children.
•When disconnecting the gas bottle ensure that all the
control valves are in the ‘OFF’ position.
•Remove the bottle from any housing in which it may be
stored before disconnection.
•When reconnecting the hose to the bottle, ensure that
all connections are tight before replacing in the storage
compartment.
•Carry out a leakage check as detailed below after each
reconnection.
electrolux e:volution barbecue installing the gas cylinder / leak test procedure / conversion to natural gas 15
Installing the gas cylinder
Conversion to Natural Gas
To install bottle:
1.Open both gas bottle compartment doors and pull out
sliding tray.
2. Wind out clamp screw to allow base of bottle to fit.
3.Place gas bottle into tray and tighten clamp to secure
bottle.
4. Make connection of gas hose to gas bottle.
Preparing the unit for Natural Gas installation.
This barbecue is supplied set up for Universal LPG and is
labelled accordingly. A Natural Gas conversion kit can be
purchased from Electrolux Spare Parts to enable conversion
to Natural Gas use.
Gas bottles vary in size and there may be some variations
that do not fit into the space provided. As an alternative to
mounting the gas bottle in slide out tray, the bottle can be
placed on the ground and hose placed through hole in rear
panel for connection to inlet.
NOTE: Conversion of this unit to Natural Gas must be
carried out by a qualified licensed person and a Certificate
of Compliance must be issued to the owner on completion
of the installation and conversion.
The conversion kit consists of:
• Regulator
• Hose with quick connect bayonet fitting one end
• Socket tool to remove injectors
• Natural Gas sticker
Procedure
1. Changing the injectors
• Remove the hotplates & grills
• Remove the flame tamers
• Remove rear heat shield (push up and then forward to
release)
rear heat shield
clamp screw
Leak test procedure (Universal LPG)
• Ensure all gas valves are in the ‘OFF’ position.
• In a small container, mix a solution of water and
detergent or soap.
• After connection of the hose, turn on the valve at the
gas bottle or mains as appropriate.
• Using a brush apply the solution to the gas connection
points and look for bubbles forming.
• Bubbling will indicate a leak.
• Turn off the valve and re-tighten the joint. Repeat the
leak test.
• If the leak persists, turn off the gas at the isolation valve
and contact a licensed gas fitter to correct.
leak test points
check hose for
signs of abrasions,
cracks or leaks
• Remove front heat shield panel
remove screws to remove front heat shield
• Remove screws securing burner at rear
remove screws securing burners
16 conversion to natural gas electrolux e:volution barbecue
Conversion to Natural Gas (cont.)
• Manoeuvre rear of burner to release front of burner
from injector
• Using socket tool provided remove first stage of
injector
injector second stage
spark plug
injector first stage
6. Leak test procedure
• Ensure all gas valves are in the ‘OFF’ position.
• In a small container, mix a solution of water and
detergent or soap.
• After connection of the hose, turn on the valve at the
gas bottle or mains as appropriate.
• Using a brush apply the solution to the gas
connection points and look for bubbles forming.
• Bubbling will indicate a leak
• Turn off the valve and re-tighten the joint. Repeat the
leak test.
• If the leak persists, turn off the gas at the isolation
valves and contact a licensed gas fitter to correct.
leak test points
• Ensure second stage of injector is not loose – tighten
if necessary
•R
efit burners ensuring the injector is located in burner
inlet
• Refit front heat shield panel and rear heat shield panel
• Refit flame tamers, grills and hotplates
2.Disconnect brass adaptor and LPG hose and
regulator assembly from gas inlet connection
3. Connect the hose to the regulator
• Place threaded end of hose through hole in rear panel
•A
pply thread tape or sealant to the male thread on the
hose and screw into the regulator.
check hose for
signs of abrasions,
cracks or leaks
7. Turndown adjustment
When converting to natural gas the turndown setting
will need to be adjusted to give satisfactory flame on
low setting.
• Remove all knobs from valve shafts of main barbecue
• Remove rubber grommets from control panel holes
• Using a Philips head screw driver, fully screw in
clockwise the valve rotation limit screw. When this is
done the valve rotation will be limited to less than 180°.
4. Connect the regulator to the barbecue gas inlet
• Fit the regulator ensuring the blue sealing washer is in
place and the arrow is pointing in the right direction
valve rotation
limit screw
barbecue gas inlet
natural gas regulator
hose with tapered
thread – thread tape
required
5. Replace the ‘gas type’ sticker
• Locate the ‘Universal LPG’ sticker located on the
barbecue gas inlet and remove it. Put the ‘Natural
Gas’ sticker in its place.
• Following connection of the gas and leak testing as
per previous steps, light all burners and set to high.
• One burner at a time turn the valve shaft to lowest
setting, observe the flame to ensure a small steady
flame is achieved.
• Turn burners off and replace rubber grommets and
control knobs.
electrolux e:volution barbecue choosing a location / installation warnings 17
Choosing a location
•The vertical clearance above the cooking surface to any
combustible materials must be at least 1000mm.
•Cooking with roasting hood closed vents the hot
flue gases out the rear of the appliance. A minimum
clearance of 450mm to any combustible materials is
required.
•The appliance requires clearance on both sides and at
rear for ventilation, ensure at least 100mm clearance.
•Avoid windy conditions as this will affect cooking
performance and burner efficiency. If this situation
cannot be avoided some shielding may be necessary.
•The barbecue grills and hotplates are slightly sloped
to enable grease & oil drainage into front receptacles.
When choosing a location ensure that the slope
towards the front is maintained.
•This appliance must be installed in accordance with
Australian Standards AS4557 and AS5601 and in
accordance with your local authority.
Installation warnings
warning
•This appliance shall only be used in an above ground,
open air situation with natural ventilation without
stagnant areas, where gas leakage and products of
combustion are rapidly dispersed by wind or natural
convection. This barbecue has been designed for
outdoor use only. Refer to diagrams below.
•Never install this barbecue inside any building, garage,
shed or breezeway or inside a boat, caravan or
recreational vehicle. This is to prevent the possibility of
fire, carbon monoxide poisoning or asphyxiation.
•Any enclosure in which this appliance is installed shall
comply with one of the following:
– An enclosure with walls on all sides, but at least
one permanent opening at the ground level and no
overhead covering.
– Within a partial enclosure that includes an overhead
cover and no more than 2 walls.
– Within a partial enclosure that includes an overhead
cover and more than 2 walls, the following shall apply:
– at least 25% of the total wall area is completely
open and at least 30% of the remaining wall area
is open and unrestricted
•In the case of balconies, at least 20% of the total of
the side, back and front wall areas shall be and remain
open and unrestricted.
Outdoor area example 1
Outdoor area example 2
Outdoor area example 3
both ends
open
Outdoor area example 4
open side at
least 25% of
total wall area
30% or more
in total of the
remaining wall
area is open and
unrestricted
open side at
least 25% of
total wall area
30% or more
in total of the
remaining wall
area is open and
unrestricted
Outdoor area example 5
18 activating the wheel brake / configuration of hotplates electrolux e:volution barbecue
Activating the wheel brake
Operating instructions
For safety, the wheel brake should be activated to prevent
any movement of the barbecue.
There are 2 wheel brakes.
Control functions
Before lighting the barbecue:
• Check that all hoses and gas fittings are tight.
• Open the roasting hood or slimline lid
NOTE the slimline lid is designed as a cover for weather
protection. The lid is not designed to be used as a cooking
hood
• Check all control knobs are in the ‘OFF’ position
• Ensure that the cooking surfaces are clean
• Turn the gas isolation valve ‘ON’
wheel brakes
To activate:
• Push down until it locks.
Options for configuration of hotplates and
grills
important
Ensure flame tamers are positioned under the grill panels
grills
Lighting instructions
•Do not attempt to light burners with cooking surfaces
covered
• Read instructions before lighting
•To light a burner, depress the knob and rotate to ‘HIGH’
•A spark is generated to light the flame thrower along
side the burner. The flame thrower makes an audible
noise and only operates when the knob is depressed to
light the burner. Release the knob and check if burner
is lit. The audible noise from the flame thrower will stop
when knob released.
•If the burner did not light, turn the knob to the ‘OFF’ position.
Allow gas to disperse, then repeat lighting procedure.
Manual lighting
•If, in the event of the automatic ignition system not
working, the barbecue can be lit manually
•A match holder with attached chain is fixed to the panel
behind top of door. For the 3 door model, it is near the
hinge of the centre door. For the 2 door model it is near
the hinge of the left door. It is accessible from inside the
cabinet.
flame tamers
Grills can be placed together on one side and hotplate on
the other.
match holder with
attaching chain located
inside channel formed
by this panel
•To light manually, fit a 40mm match to the holder and
light. Pass match through viewing slots below the front
cooking plate down towards the burner, then rotate
knob to HIGH to ignite. If ignition fails, turn the control
valve OFF and allow several minutes for the gas to
disperse before attempting to light again.
pass match holder
through viewing slot
at front under cooking
plates
Grills can be placed either side of hotplate. This is the
preferred option for roasting.
•Once alight, repeat for other burners as required.
electrolux e:volution barbecue operating instructions / using the roasting hood 19
Using the roasting hood
Preheating
•This barbecue is fitted with high power burners. In
most conditions it will only be necessary to preheat the
barbecue for 5 minutes before cooking can commence
•As with most things, experience will familiarise you with
the effectiveness of and the time required to achieve the
desired preheating time to obtain the desired cooking
temperature
•Testing has shown that the burners can be turned to
low position for satisfactory cooking
•If the unit does not operate correctly refer to the
troubleshooting section on page 22
•If the burners are left to run too hot there will be excessive
smoking during the cooking process and subsequent
burning of the food being prepared. This may also result
in excessive flaring of the fat being emitted from the food
•Roasting with the hood closed only requires the 2
outermost burners on low setting for satisfactory cooking.
To turn the burner off
•When cooking is complete, rotate the knob fully
clockwise so the pointer on the knob is positioned at
the ‘OFF’ position
•Turn gas bottle isolation valve off after turning all knobs
to ‘OFF’ position when appliance not in use
Cooking with the hood closed only requires 2 burners to
be on low setting. Setting is to be adjusted depending on
conditions and using the temperature indicator as a guide.
•It is recommended when roasting to place the solid
hot plate in the centre with one grill on each side of the
plate. Use the two outer burners under the grills.
•To achieve even cooking of the food, place the food
onto a wire rack above the hot plate to allow air to
circulate under the food.
•Food can also be placed on the warming racks for
cooking with hood closed
warning
• Do not use more than 2 burners when hood closed and
do not allow the temperature to exceed the ‘Ready’
zone of the temperature indicator. These conditions
create excessive heat and may cause damage to the
barbecue and roasting hood.
• When cooking with the hood closed the hot flue
gases flow out the rear of the appliance between the
splashguard and the hood. Ensure the barbecue is
suitably located to avoid damage or injury.
warning
nly use a minimum amount of oil as excess
O
oil can cause the flames to ignite further.
20 using the side table / lid safety leg electrolux e:volution barbecue
Using the side table
Lid safety leg – slimline lid only
To extend the side tables:
• Lift upwards until it locks
To ensure that the user remembers to turn off the gas
before closing the lid, a pivoting safety leg has been fitted
(both small and large lids).
pivoting safety leg
lift upwards
To fold back into place:
1. Lift upwards slightly to unlock
2.Slide support arms upwards and table should fall into
place.
When closing the lid the safety leg will pivot forward and
rest against the trim surface to prevent the lid closing. After
ensuring the gas has been turned off, to fully close the lid,
the leg needs to be rotated backwards.
pivoting safety leg
lift upwards
warning
THE SLIMLINE LID MUST NOT BE CLOSED WHEN
THE BURNERS ARE OPERATING.
Closing the lid during burner operation can cause
discolouration and damage to the lid and barbecue unit.
electrolux e:volution barbecue cleaning and care 21
Cleaning and care
This Electrolux barbecue has been constructed from select
grade stainless steel which, if not cared for, may discolour
over time. To keep your barbecue looking its best we
recommend that the cooking surfaces are cleaned after
every use.
warning
Please ensure that your barbecue is switched off and
has cooled down before following the instructions
below.
Cast iron plates
The cooking plates and grills have a porcelain enamelled
coating.
NOTE: Many food acids, juices, marinades and sauces
contain highly acidic elements that will slowly attack the
surface of the cast iron if not removed immediately after
cooking.
After use remove all solid material from the cooking surface
using a brass bristled barbecue brush or plastic bristled
scourer. Wipe off the remaining grease with paper towelling.
Gently wash the surfaces with a cloth or sponge and a mild
detergent and hot water. Dry components immediately and
coat the cooking surface with a light layer of cooking oil.
This protects the surface when not in use. Do not clean the
cooking surface in a dishwasher
Cleaning inside the barbecue
The inside of the burner box should be regularly cleaned to
prevent any build up of food residues.
To access the burner box remove cooking plates and heat
distributors. To remove rear heat shield lift to disengage
clips. To remove burners undo screws securing burners at
rear, and lift out carefully to prevent scratching. The base
heat shields can also be lifted out.
Ensure that all oil and food residues are removed.
After cleaning complete, re-assemble ensuring burner is
correctly located over the injector.
screws securing burners
rear heat shield
base heat shield
Cleaning the oil reservoirs
The barbecue has a unique oil management system which
drains oil to the front into easily removed reservoirs which
should be cleaned after each use.
• To remove reservoirs, pull upwards from the front of the
barbecue and dispose of the contents of the catchment
responsibly. Rinse oil reservoirs in warm soapy water. The
reservoirs can be placed in the dishwasher if desired.
Cleaning stainless steel surfaces
caution
Do not use abrasive or caustic cleaners, scourers or
metal scrapers on stainless steel surfaces as they may
permanently scratch and damage your barbecue.
• Wash all stainless steel components, including the
slimline lid, the roasting hood, tubular frame and control
knobs with a soft dishcloth using hot soapy water
• The barbecue interior can be wiped down with a soft
cloth in hot soapy water. The rear panel of the interior is
removable for easy cleaning
• Ensure that all surfaces are dried with a clean dry cloth
tips and information
Sometimes stainless steel surfaces are affected by a brown
discolouration called tea staining. This usually occurs in
areas which use high heat and can be removed using
specialised stainless steel cleaners. For best results, we
recommend that specialised cleaners be used regularly on
all stainless steel components. You will find these cleaners
at the Electrolux spare parts outlets.
Powder coated panels
Do not use abrasive or caustic cleaners, scourers or metal
scrapers as they may permanently damage your barbecue.
Wash all powder coated panels with a soft dishcloth using
warm soapy water. Ensure that all surfaces are dried with a
clean dry cloth.
Side table timber
The hardwood used on the lift up side tables has been
treated with a light coating of protection oil. Clean surface
using a soft sponge and a solution of mild soapy water.
Wash down afterwards with clean water.
To maintain strength, avoid discolouration and fading, the
timber must be protected using a suitable outdoor timber
furniture oil. Re-oiling of timber will need to be conducted at
regular intervals depending upon the amount of exposure to
the sun and rain.
Minor scuffs and scratches can easily be covered with a
coat of oil. Deep scratches need to be sanded out and
oiling concentrated in that area until the lustre is uniform.
Use of a weatherproof cover will help to minimise the
maintenance required.
tips and information
caution
Take extra care (particularly when cleaning on and around
the control knobs) to ensure that water and soapy residue
do not enter the control panel.
Care should also be taken not to disturb the spark
electrode.
The stainless steel panels may distort while in use but will
return to normal when cold.
When the barbecue is not being used it is recommended to
keep it covered.
If the barbecue is to be stored indoors, remove the gas
cylinder and store the cylinder in a ventilated outdoor area.
22 maintenance / troubleshooting electrolux e:volution barbecue
Maintenance
Stainless steel burners
Burners should be checked at least once per year and
cleaned as necessary. Inspect burners to ensure no
residues have been deposited and gas ports are clear.
Troubleshooting
problem
possible cause
remedy
Barbecue won’t
light
No gas
Check isolation valve
is ON
Gas bottle empty – refill
or change gas bottle
Ignition system
not working
Check there is a spark
being generated when
knob rotated
Ignition electrode wet or
dirty, gently clean and
dry electrode, ensuring
position is unchanged
Manually light the
barbecue
Excess smoke
being emitted
from the cooking
area
Too much heat
Turn down gas valve or
turn off selected burners
Smell of gas
Gas leak
Turn off gas at the
isolation valves
DO NOT
ATTEMPT TO
LIGHT THE
APPLIANCE
Check for leaks, tighten
joints
If problem persists, call
Electrolux Service
electrolux e:volution barbecue warranty 23
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: ELECTROLUX E:VOLUTION BARBECUE
This document sets out the terms and conditions of product
warranties for Electrolux branded appliances. It is an important
document. Please keep it with your proof of purchase documents in
a safe place for future reference should you require service for your
Electrolux appliance.
General Terms and Conditions
1. In this warranty
(a)‘Electrolux’ means Electrolux Home Products Pty Ltd ABN 51
004 762 341 in respect of Appliances purchased in Australia and
Electrolux (NZ) Limited in respect of Appliances purchased in New
Zealand;
(b)‘Appliance’ means any Electrolux product purchased by you
accompanied by this document;
(c)‘Warranty Period’ means
(i)where you use the Appliance for personal, domestic or household
purposes in Australia the period of ‘24’ months and in New
Zealand the period of ‘24’ months;
(ii)where you use the Appliance for commercial purposes, in
Australia the period of ‘3’ months and in New Zealand the period
of ‘3’ months, (if the period stated is 0 months you are not
covered by this product warranty) following the date of original
purchase of the Appliance;
(d)‘you’ means the purchaser of the Appliance not having purchased
the appliance for re-sale, and ‘your’ has a corresponding meaning.
2.This warranty only applies to Appliances purchased and used in
Australia or New Zealand and is in addition to (and does not exclude,
restrict, or modify in any way) any non-excludable statutory warranties
in Australia or New Zealand.
3.Electrolux warrants that, when dispatched from an Electrolux
warehouse, the Appliance is free from defects in materials and
workmanship for the Warranty Period.
4.During the Warranty Period Electrolux or its Authorised Service Centre
will, at no extra charge if your appliance is readily accessible without
special equipment, and subject to these terms and conditions, repair
or replace any parts which it considers to be defective. Electrolux or
its ASC may use reconditioned parts to repair your appliance. You
agree that any replaced Appliances or parts become the property of
Electrolux. This warranty does not apply to light globes, batteries, filters
or similar perishable parts.
5.Parts and Appliances not supplied by Electrolux are not covered by this
warranty.
6.Where you are within an Electrolux service area, this warranty covers
the cost of transport of the Appliance to and from Authorised Service
Centres of Electrolux and travelling costs for representatives of the
Authorised Service Centre to and from your home or business. If you
are outside an Electrolux service area, you will bear these costs. For
information about whether you are within an Electrolux service area,
please phone 13 13 49 in Australia, or 0800 10 66 10 in New Zealand.
7.Proof of purchase is required before you can make a claim under this
warranty.
8.You may not make a claim under this warranty unless the defect
claimed is due to faulty or defective parts or workmanship. Electrolux is
not liable in the following situations (which are not exhaustive):
(a) The Appliance is damaged by:
(i) accident
(ii)misuse or abuse, including failure to properly maintain or service
(iii)normal wear and tear
(iv)power surges, electrical storm damage or incorrect power
supply
(v)incomplete or improper installation
(vi) incorrect, improper or inappropriate operation
(vii) insect or vermin infestation.
(b)The Appliance is modified without authority from Electrolux in
writing.
(c)The Appliance’s serial number or warranty seal has been removed
or defaced.
(d)The Appliance was serviced or repaired by anyone other than
Electrolux or its Authorised Service Centres.
9.This warranty, the contract to which it relates and the relationship between
you and Electrolux are governed by the law applicable in the Australian
State where the Appliance was purchased or the law applicable in New
Zealand if the Appliance was purchased in New Zealand. Where the
Appliance was purchased in New Zealand for business purposes the
Consumer Guarantee Act does not apply.
Limitation of Liability
10.To the extent permitted by law:
(a)Electrolux excludes all warranties other than as contained in this
document;
(b)Electrolux shall not be liable for any loss or damage whether direct
or indirect or consequential arising from your purchase, use or nonuse of
the Appliance.
11.Provisions of the Trade Practices Act and State consumer legislation
in Australia, and the Consumer Guarantees Act, the Sale of Goods
Act and the Fair Trading Act in New Zealand, imply warranties or
conditions, or impose obligations, upon Electrolux which cannot be
excluded, restricted or modified. To the extent permitted by law, the
liability of Electrolux (if any) arising out of or in relation to the Appliance
or any services supplied by Electrolux shall be limited (where it is fair
and reasonable to do so),:
(a)in the case of Appliances, at its option, to the replacement or
repair of the Appliances or the supply of equivalent products or
the payment of the cost of replacing the Appliances or having the
Appliances repaired or of acquiring equivalent Appliances. Upon
being replaced, parts and Appliances become the property of
Electrolux; or
(b)in the case of services, at its option, to the supply of the services
again or the payment of the cost of having the services re-supplied;
and in the case of Appliances or services supplied in New Zealand,
loss or damage whether direct or indirect or consequential that is
reasonably foreseeable.
Privacy
You acknowledge that in the event that you make a warranty claim it will be
necessary for Electrolux and its Authorised Service Centres to exchange
information in relation to you to enable Electrolux to meet its obligations
under this warranty.
Important Notice
Before Calling a Service Technician please check carefully the operating instructions, service booklet and the warranty terms and conditions.
FOR SERVICE
or to find the address of your nearest
state service centre in Australia
Please call 13 13 49
For the cost of a local call (Australia only)
FOR SERVICE
or to find the address of your nearest
authorised service centre in New Zealand
Free call 0800 10 66 10
(New Zealand only)
SERVICE AUSTRALIA
ELECTROLUX HOME PRODUCTS
www.electrolux.com.au
SERVICE NEW ZEALAND
ELECTROLUX HOME PRODUCTS
www.electrolux.co.nz
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in Australia
Please call 13 13 50
For the cost of a local call (Australia only)
FOR SPARE PARTS
or to find the address of your nearest
state spare parts centre in New Zealand
Free call 0800 10 66 20
(New Zealand only)
Electrolux Home Products Australia
telephone: 1300 363 640
fax:
1800 350 067
email:
customercare@electrolux.com.au
web:
www.electrolux.com.au
Electrolux Home Products New Zealand
telephone: 09 573 2384
fax:
09 573 2221
email:
customercare@electrolux.co.nz
web:
www.electrolux.co.nz
The Thoughtful Design Innovator.
Do you remember the last time you opened a gift that made you say
“Oh! How did you know? That’s exactly what I wanted!” That’s the kind of
feeling that the designers at Electrolux seek to evoke in everyone who
chooses or uses one of our products. We devote time, knowledge, and a
great deal of thought to anticipating and creating the kind of appliances that
our customers really need and want.
This kind of thoughtful care means innovating with insight. Not design for
design’s sake, but design for the user’s sake. For us, thoughtful design means
making appliances easier to use and tasks more enjoyable to perform, freeing
our customers to experience that ultimate 21st century luxury, ease of mind.
Our aim is to make this ease of mind more available to more people in more
parts of their everyday lives, all over the world. So when we say we’re thinking
of you, you know we mean just that.
The “Thinking of you” promise from Electrolux goes beyond meeting the needs
of today’s consumers. It also means we’re committed to making appliances
safe for the environment—now and for future generations.
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com.au or www.electrolux.co.nz
P/No. 0616 001 946
© Copyright 2010 Electrolux Home Products Pty Ltd
ABN 51 004 762 341
Print code: EEVOBBQUM_Jun10