- No category
advertisement
▼
Scroll to page 2
of 5
e \ . i 1 .) *I # BIRADIAL ELLIPTICAL The Shure M94 LT Cartridge, mounts directly t o Technics Linear Tracklng Turntables such as Models SL5, SL7, SLlO and SL15 This cartridge brings outstanding trackability and transparent frequency response t o the Technics Linear Tracking Turntables TRACKING FORCE The M94 I T is designed t o operate at a tracklng force of 1.25 grams optimum. D o not use tracking forces heavler than 1 5 grams Consult the turntable manufacturer if you have any doubts about whether its tracking force is appropriate. MOUNTING, MONTAGE, MONTAJE SPECIFICATIONS Frequency Response: 20 t o 20,000 H z Typical Trackability (at 1.25 grams tracklng force, in cm/sec peak velocity): 10,000 Hz - 16 cmlsec 400 Hz - 26 crnlsec 1.000 H z - 30 cmlsec Output Voltage (at 1,000 Hz, 5 cmlsec peak velocity): 4 5 mV per channel Channel Balance: Within 2 dB Channel Separation (minimum): 25 dB at 1,000 H z Optimum Load: 47,000 ohms resistance in parallel with 200 t o 300 picofarads capacitance per channel Load resistance can be up to 70.000 ohms w ~ t halmost no audible change in frequency response Total capacitance includes both the tone arm wiring and amplifier input circuit Inductance: 700 milllhenrles DC Resistance: 1550 ohms Net weight: 6 grams Replacement Stylus: N94LT with 10 x 18p (0004 x ,0007 in.), biradial elliptical diamond tip, Dark Blue grlp al m 2 FIGURE 1 3 STYLUS CLEANING Use a soft brush with an alcohol-distilled water solution or Shure Stylus Cleaning Solution (See your dealer and ask for the Shure SK-I, Stylus Clean~ngKit ) Brush only from back t o front as shown in Figure 2. Other commerc~alcleaning solutions may cause stylus damage STYLUS REPLACEMENT Place the Techn~csL~nearTrack~ngarm In a conve n ~ e np t o s ~ t ~ oasn follows 1 W ~ t hthe Ild closed use the"manual"mode t o move the arm to approx~matelythe center of ~ t stravel 2 Make certaln the cartr~dge1s cued "up" (ra~sedoff the record), and press the O f f O n s w ~ t c h" O f f " 3 Ra~sethe 11d Replace the stylus as shown In F~gure3 Always hold the stylus only by the plast~cgrlp, take care not to touch or damage the thank or d ~ a m o n dt ~ p STYLUS CLEANING FIGURE 2 I 1 TI?! STYLUS REPLACEMENT FIGURE 3 PREAMPLIFIER SETTING The M94 LT is a moving magnet cartridge If your Technics Linear Tracking Turntable has a preamplifier selector swltch, be sure t o set the switch t o the moving magnet position (MM) SPECIAL NOTE As the only source of contact between the record groove and the balance of your high fidelity system, the stylus in your cartridge plays a crltlcal role in the ultimate quality of sound reproduction. Additionally, because records can be irreparably damaged by a worn stylus, it is essential to ensure that your Shure stylus is in peak condition in order t o preserve your records in "mlnt" condition. Your cartr~dgecan perform at original operating specifications for many years with these simple maintenance steps: 1. Follow the stylus cleaning instructions given on page 4 2. See your Shure dealer at least once a year for a checkup of your cartridge's stylus. He'll clean it and inspect i t for wear. 3. When it becomes necessary t o replace your stylus, insist on a genulne Shure replacement Extensive testing of imitations of Shure styli revealed numerous grave flaws To be c e r t a ~ nthat your replacement stylus meets orlglnal specifications, look for the name SHURE@on the stylus grip and the words "This Stereo DYNETIC@stylus is precision manufactured by Shure Brothers Inc." on the stvlus box. R E C O M M A N D A T I O N S POUR LE NETTOYAGE DE LA POINTE: Utilisez une brosse douce, humectee d'alcool pur ou dilue. Les liquides de nettoyage vendus dans le commerce peuvent endommager ou corroder la pointe. Brossez toujours d'arriere en avant. REMPLACEMENT D U D I A M A N T : Placer le bras de la. platlne Technics dans la position adequate. Operer comme suit: 1. Le capot etant ferme, utiliser le mode "manuel" pour placer le bras approximativement a mi-course. 2. S'assurer que le bras est en position "up"(cellule non en contact avec le d~sque), et mettre le contacteur d'alimentation de la platine sur "off." 3. Soulever le capot. Remplacer le diamant comme la figure. Tenir ledlamant par le plastique, prendre garde a ne pas toucher ou endommager le diamant ou le tube porte pointe REGLAGE D U PREAMPLI: La M94 LT est une cellule a aimant mobile Si votre platine Technics a un preampli cellule incorpore, assurez vous que le selecteurest sur la position MM (moving magnet). FORCE D'APPUI: La M94 LT est concu pour fonctionner a une force d'appui optimale de 1.25 g. Ne pas utiliser de pression plus importante que 1,5 g. En cas de doute, contacter le fabricant de le platine afin de s'assurer que la force d'appui est correcte FULL ONE-YEAR W A R R A N T Y : Shure Brothers lncorporated ("Shure"). 222 Hartrey Avenue, Evanston, Illinois 60204, warrants to the owner of this product that it will be free, In normal use, of any defects in workmanship and materials for a period of one year from date of purchase You should r e t a ~ nproof of date of purchase Shure is not llable for any consequential damages If this Shure product has any defects as described above, carefully repack the unit and return it prepaid to: Shure Brothers lncorporated Attention: Servlce Department 1501 West Shure Drive Arlington Heights, Illinois 60004 If you are not In the United States, return the unlt to your dealer or Authorized Serv~ceCenter for repair The untt will be repaired or replaced and returned t o you promptly, and if it cannot be repaired or replaced, you may elect to receive a refund. This warranty does not include stylus wear PATENT NOTICE: All Shure Styli and Cartridges are manufactured under one or more of the f o l l o w ~ n gU S Patents. 3.055.988; 3,077,521, 3,077,522, 3,463,889; 4,270,758; 4,194,744, 4,275,888. D l 93,854; D l 93,934, D201.803, D235,070, D235.351. D235.352. D245.022, D245.433, D252.628, 0254,004, D257,676, D255.898, D258.586; other patents pending Copyright 1982. Shure Brothers Inc 27A1732 (HA) Printed ~nU 5 A 9
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project