Zanussi ZGP 982 Technical data

GAS HOB
ZGP 982
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
GB
Important Safety Information
You MUST read these warnings carefully before installing or using the oven. If you need assistance,
contact our Customer Care Department on 08705 727727
Installation
l
l
l
l
l
This hob must be installed by qualified personnel,
according to the manufacturer’s instructions and to
the relevant British Standards.
Any gas installation must be carried out by a
registered CORGI installer.
Remove all packaging before using the hob.
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near
the gas supply pipe.
Do not attempt to modify the hob in any way.
Service
l
This hob should only be repaired or serviced by an
authorised Service Engineer and only genuine
approved spare parts should be used.
Environmental Information
l
l
After installation, please dispose of the packaging with
due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
Child Safety
l
l
l
l
This hob is designed to be operated by adults. Do
not allow children to play near or with the hob.
The hob gets hot when it is in use.
Children should be kept away until it has cooled.
Children can also injure themselves by pulling pans
or pots off the hob.
During Use
l
l
l
l
l
l
l
l
l
l
2
This hob is intended for domestic cooking only. It is
not designed for commercial or industrial purposes.
When in use a gas cooking appliance will produce
heat and moisture in the room in which it has been
installed. Ensure there is a continuous air supply,
keeping air vents in good condition or installing a
cooker hood with a venting hose.
When using the hob for a long period of time, the
ventilation should be improved, by opening a window
or increasing the extractor speed.
Do not use this hob if it is in contact with water.
Do not operate the hob with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
When using other electrical appliances, ensure the
cable does not come into contact with the hot surfaces
of the cooking appliance.
Unstable or misshapen pans should not be used on
the hob as unstable pans can cause an accident by
tipping or spillage.
Never leave the hob unattended when cooking with
oil and fats.
Never use plastic or aluminium foil dishes on the hob.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above or
below the hob unit.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
F
Step by step instructions for an operation
Hints and Tips
Enviromental information
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683 (Low VoltageDirective);
* 93/68 (General Directives);
* 89/336 (Electromagnetical Compatibility
Directive);
* 90/396 (Gas Appliances),
and subsequent modifications
Contents
For the Installer
For the User
Important Safety Information
2
Important Safety Requirements
10
Description of the Hob
3
Installation
10
Operation
4
Fitting the hob to the worktop
11
Maintenance and Cleaning
4
Electrical connections
12
Something Not Working?
5
Wiring Diagram
13
Service and Spare Parts
5
Fault Finding
13
Guarantee Conditions
6
Commissioning
15
Conversion from Natural Gas to LPG
15
Description of the Hob
4
3
3
1
2
1. Rapid Burner
2. Auxiliary Burner
3. Semi-rapid Burners
4. Ultra-rapid Double crown Burner
3
Operation
Hob burners
F
l
l
l
l
To light a burner:
push in the relevant control knob and turn it to
maximum position.
Upon ignition, keep the knob pushed down about 5
seconds. This will allow the "thermocouple" (Fig. 1
letter C) to be heated and the safety device to be
switched off, otherwise the gas supply would be
interrupted.
Then adjust the flame as required.
If the burner does not ignite, turn the control knob to
zero, and try again.
If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the vessel, causing the handle to
overheat.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
If the control knobs become difficult to turn, please
contact your local Service Centre.
Fig. 1
A - Burner cap
B - Burner crown
C - Ignition candle
D - Thermocouple
FO 0204
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner
Ultra-rapid
(double crown)
Large (rapid)
Medium (semi-rapid)
Small (Auxiliary)
minimum
diameter
180 mm.
180 mm.
120 mm.
80 mm.
maximum
diameter
260 mm.
260 mm.
220 mm.
160 mm.
Maintenance and Cleaning
Before any maintenance or cleaning can be carried
out, you must DISCONNECT the hob from the
electricity supply.
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is
left to cool.
The Hob Top
Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little washing up liquid
has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.
Ignition candle
The electric ignition is obtained through a ceramic
"candle" and a metal electrode (fig. 1 letter B). Keep
these components well clean, to avoid difficult lighting,
and check that the burner crown holes are not
obstructed.
4
Pan Supports
The hob has cast iron pan supports. Take care when
removing them. They are fairly heavy and could damage
the hob or your kitchen furniture if you let them fall down.
Wash the pan supports using hot soapy water. If
necessary, a paste cleaner or a soap impregnated steel
wool pad can be used with caution.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burner caps and crowns using hot soapy water,
and remove marks with a mild paste cleaner. A well
moistened soap impregnated steel wool pad can be used
with caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft cloth.
Something Not Working?
If the hob is not working correctly, please carry out the following checks before contacting your local Service Force
Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
SYMPTOM
SOLUTION
n There is no spark when lighting the gas
u Check that the unit is plugged in and the electrical
supply is switched on
u Check that the RCCB has not tripped (if fitted)
u Check the mains fuse has not blown
u Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
n The gas ring burns unevenly
u Check the main jet is not blocked and the burner
crown is clear of food particles.
u Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
If after all these checks, your hob still does not operate
correctly, contact your local Service Force Centre.
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.
Service and Spare Parts
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Zanussi Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area. The
addresses are listed on the following pages.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working.”
When you contact the Service Force Centre you will need
to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.
5
Customer Care Department
For general enquiries concerning your Zanussi appliance
or for further information on Zanussi products, please
contact our Customer Care Department by letter or
telephone at the address below or visit our website at
www.zanussi.co.uk
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
* calls to this number may be recorded for training
purposes.
Guarantee Conditions
Zanussi Guarantee conditions
We, Zanussi, undertake that if, within 24 months of the
date of the purchase, this Zanussi appliance or any part
thereof is proved to be defective by any reason only of
faulty workmanship or materials, we will, at our option,
repair or replace the same FREE OF ANY CHARGE for
labour, materials or carriage on condition that:
*
The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
* The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
* All service work under this guarantee must be
undertaken by a Zanussi Service Centre.
* Any appliance or defective part replaced shall
become the Company's property.
* This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours, in which case a premium will be charged.
Exclusions
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
6
*
*
Appliances found to be in use within a commercial
or similar environment, plus those which are the
subject to rental agreements.
Products of Zanussi manufacture which are not
marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European Community
(EC) or European Free Trade Area.
* The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
* The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
France
Senlis
+33 (0)3 44 62 29 99
Germany
Nürnberg
+49 (0)911 323 2600
Italy
Pordenone +39 (0)1678 47053
Sweden
Stockholm +46 (0)8 738 79 50
UK
Slough
+44 (0)1753 219897
ZANUSSI SERVICE FORCE
To contact your local Zanussi Service Force Centre telephone 08705 929 929
CHANNEL ISLANDS
GUERNSEY
JERSEY
Guernsey Electricity
PO Box 4
Vale, Guernsey
Channel Islands
Jersey Electricity Company
PO Box 45
Queens Road
St Helier
Jersey
Channel Islands JE4 8NY
ORKNEY
(M65)
Corsie Domestics
7 King Street
Kirkwall
Orkney KW15
PERTH
Hydro Electrical
Inveralmond House
Ruthervenfield Road
Perth PH1 3AQ
PERTH
(OWN SALES)
SCOTLAND
ABERDEEN
(M05)
AUCHTERMUCHY
(M03)
BLANTYRE
(M07)
54 Claremont Street
Aberdeen AB10 6RA
33a Burnside
Auchtermuchy
Fife KY14 7AJ
Unit 5
Block 2
Auchenraith Ind. Estate
Rosendale Way
Blantyre G72 0NJ
DUMFRIES
(M01)
93 Irish Street
Dumfries
Scotland DG1 2 PQ
DUNOON
(M67)
Brair Hill
7 Hill Street
Dunoon
Argyll PA23 7AL
GLASGOW
(M04)
20 Cunningham Road
Clyde Estate
Rutherglen
Glasgow G73 1PP
INVERNESS
(M06)
Unit 3B
Smithton Ind. Estate
Smithton
Inverness IV1 AJ
ISLE OF ARRAN
Arran Domestics
Unit 4 The Douglas Centre
Brodick
Isle of Arran KA27 8AJ
(OWN SALES)
ISLE OF BARRA
(OWN SALES)
J Zerfah
244 Bruernish
Isle of Barra
Western Islands HS9 5QY
ISLES OF BUTE
(M66)
Walker Engineering
Glenmhor
Upper Serpentine Road
Rothesay
Isle of Bute PA20 9EH
ISLE OF LEWIS
(M69)
ND Macleod
16 James Street
Stornoway
Isle of Lewis PA87 2QW
KELSO
(M08)
2-8 Wood Market
Kelso
Borders TD5 7AX
SHETLAND
(OWN SALES)
SHETLAND
(OWN SALES)
Graham Begg
Unit 4
Airport Ind Estate
Wick KW1 4QS
Tait Electronic Systems Ltd
Holmsgarth Road
Lerwick
Shetland ZE1 0PW
Bolts Shetland Ltd.
26 North Road
Lerwick
Shetland ZE1 0PE
WHALSAY
Leask Electrical
Harisdale
Symbister, Whalsay
(OWN SALES)
Shetland ZE2 9AA
NORTH EAST
GATESHEAD
(M39)
Unit 356a
Dukesway Court
Dukesway
Team Valley
Gateshead NE11 0BH
GRIMSBY
(M42)
15 Hainton Avenue
Grimsby
South Humberside
DN32 9AS
HULL
(M41)
Unit 1
Boulevard Industrial
Estate
Hull
HU3 4AY
LEEDS
(M37)
64-66 Cross Gates Road
Leeds
LS15 7NN
NEWTON AYCLIFFE Unit 16
(M45)
Gurney Way
Aycliffe Industrial Estate
Newton Aycliffe
DL5 6UJ
SHEFFIELD
(M38)
NORTHERN IRELAND
BELFAST
(M27)
Owenmore House
Kilwee Business Park
Upper Dunmury Lane
Belfast
BT17 0HD
Pennine House
Roman Ridge Ind.
Roman Ridge Road
Sheffield
S9 1GB
NORTH WEST
BIRKENHEAD
(M11)
1 Kelvin Park
Dock Road
Birkenhead
L41 1LT
WALES
CARDIFF
(M28)
Guardian Industrial Estate
Clydesmuir Road
Tremorfa
Cardiff
CF2 2QS
CARLISLE
(M10)
Unit 7
James Street Workshops
James Street
Carlisle
Cumbria
CA2 5AH
CLYWD
(M14)
Unit 6-7 Coed – Parc
Abergele Road
Rhuddlan
Clwyd
Wales
LL18 5UG
ISLE OF MAN
(M64)
South Quay Ind. Estate
Douglas
Isle of Man
IM1 5AT
LIVERPOOL
(M15)
Unit 1
Honeys Green Precinct
Honeys Green Lane
Liverpool
L12 9JH
MANCHESTER
(M09)
Unit B
Central Industrial Estate
St Marks Street
Bolton
BL3 6NR
PRESTON
(M13)
Unit 250
Dawson Place
Walton Summit
Bamber Bridge
Preston
Lancashire PR5 8AL
STOCKPORT
(M16)
Unit 20 Haigh Park
Haigh Avenue
Stockport
SK4 1QR
DYFED
(M77)
HAVERFORDWEST
(M75)
Maes Y Coed
High Mead
Llanybydder
Carmarthenshire
SA40 9UL
Cromlech Lodge
Ambleston
Haverfordwest
Pembrokeshire
SA62 5DS
OSWESTRY
(M17)
Plas Ffynnon
Warehouse
Middleton Road
Oswestry
SY11 2PP
7
ZANUSSI SERVICE FORCE
To contact your local Zanussi Service Force Centre telephone 08705 929 929
MIDLANDS
BIRMINGHAM
(M18)
66 Birch Road East
Wyrley Road Ind. Estate
Witton
Birmingham
B6 6DB
BOURNE
Manning Road Ind.
Estate
Pinfold Road
Bourne
PE10 9HT
(M44)
BRIDGNORTH
(M72)
68 St. Mary’s Street
Bridgnorth
Shropshire
WV16 4DR
LONDON & EAST ANGLIA
11a Gardener Ind. Estate
Kent House Lane
Beckenham
Kent BR3 1QZ
CHELMSFORD
(M47)
Hanbury Road
Widford Ind. Estate
Chelmsford
Essex
CM12 3AE
ASHFORD
(M58)
Unit 14
Capitol Park
Capitol Way
Colindale
London NW9 0EQ
Unit 2
Bridge Road Business Est.
Bridge Road
Ashford
Kent TN2 1BB
FLEET
(M59)
Unit 1
Redsfield Ind. Estate
Church Crookham
Fleet
Hampshire GU13 0RD
HAYWARDS
HEATH
(M55)
21-25 Bridge Road
Haywards Heath
Sussex RH16 1UA
COLINDALE
(M53)
101 Rycroft Street
Gloucester
GL1 4NB
ELTHAM
(M78)
HEREFORD
(M31)
Unit 3
Bank Buildings
Cattle market
Hareford
HE4 9HX
194 Court Road
Mottingham
Eltham
London SE9 4EW
ENFIELD
(M49)
284 Alma Road
Enfield
London
EN3 7BB
30 High Street
Higham Ferrers
Northants
NN10 8BB
ILKESTON
(M43)
Unit 2
Furnace Road
Ilkeston DE7 5EP
LEICESTER
(M22)
Unit 7
Oaks Ind. Estate
Coventry Road
Narborough
Leicestershire
LE0 5GF
LINCOLN
(M40)
Unit 8
Stonefield Park
Clifton Street
Lincoln
LN5 8AA
NEWCASTLE
UNDER LYME
(M12)
18-21 Croft Road
Brampton Ind. Estate
Newcastle under Lyme
Staffordshire
ST5 0TW
REDDITCH
(M20)
13 Thornhill Road
North Moons Moat
Redditch
Worcestershire
B98 9ND
TAMWORTH
(M19)
Unit 3
Sterling Park
Claymore
Tamworth
B77 5DO
WORCESTER
(M73)
8
Units 1 & 2
Northbrook Close
Gregorys Mill Ind. Estate
Worcester
WR3 8BP
Unit 1a
The Summit
Hanworth Road
Hanworth Ind. Estate
Sunbury on Thames
TW16 5D
BECKENHAM
(M79)
GLOUCESTER
(M23)
HIGHAM FERRERS
(M51)
SUNBURY
(M63)
GRAVESEND
(M57)
Unit B4
Imperial Business Estate
Gravesend
Kent
DA11 0DL
HARPENDEN
(M46)
Unit 4
Riverside Estate
Coldharbour Lane
Harpenden
AL5 4UN
LETCHWORTH
(M50)
16-17 Woodside Ind. Estate
Works Road
Letchworth
Herts
SG6 1LA
LONDON
(M76)
2/4 Royal Lane
Yiewsley
West Drayton
Middlesex
UB7 8DL
MAIDENHEAD
(M60)
Reform Road
Maidenhead
Berkshire
SL6 8BY
MOLESEY
(M61)
10 Island Farm Avenue
West Molesey
Surrey
KT8 2UZ
NEWBURY
(M24)
9 Pipers Court
Berkshire Drive
Thatcham
Berkshire
RG19 4ER
IPSWICH
(M48)
Unit 6C
Elton Park Business Centre
Hadleigh Road
Ipswich
IP2 0DD
NORWICH
(M52)
2b Trafalgar Street
Norwich
NR1 3HN
SOUTH EAST
SOUTH WEST
BARNSTAPLE
(M30)
Main Road
Fremington
Barnstaple
North Devon EX31 2NT
BOURNEMOUTH
(M26)
63-65 Curzon Road
Bournemouth
Dorset
BH1 4PW
BRIDGEWATER
(M35)
6 Hamp Ind. Estate
Bridgewater
Somerset TA6 3NT
BRISTOL
(M25)
11 Eldon Way
Eldonwall Trading
Bristol
Avon BS4 3QQ
EMSWORTH
(M33)
266 Main Road
Southbourne
Emsworth
PO10 8JL
ISLE OF WIGHT
(M34)
Unit 8
Enterprise Court
Ryde Business Park
Ryde
Isle of Wight PO33 1DB
NEWTON ABBOT
(M29)
Unit 2
Zealley Ind. Estate
Kingsteignton
Newton Abbot
S. Devon
TQ12 3TD
REDRUTH
(M36)
Unit 7D
Pool Ind. Estate
Wilson Way
Redruth
Cornwall TR15 3QW
Instructions for the Installer
Engineers technical data
OVERALL DIMENSIONS
Spark Generator
Width:
Depth:
Height:
Spark Gap
900 mm.
600 mm.
100 mm.
Ispra Control's BF 50066 230-240V 0.6 YA T 120
Fixed
Rear Left Burner (semi-rapid)
Heat Input
2.0 kW (6824 BTU/HR)
SUPPLY CONNECTIONS
Gas:
RC 1/2 inch (1/2 inch male) Rear right hand corner
Front Left Burner (rapid)
Heat Input
3.0 kW Natural gas (10236 BTU/HR)
2.8 kW LPG (9554 BTU/HR)
Electric:
230-240V 50Hz supply, 3 core flexible cable with non
rewireable plug fitted with a 3 amp cartridge fuse.
Rear Right Burner (semi-rapid)
Heat Input
2.0 kW (6824 BTU/HR)
Front Right Burner (auxiliary)
Heat Input
1.0 kW (3412 BTU/HR)
Central Burner (Ultra-rapid Double crown)
Heat Input
3.5 kW (11942 BTU/HR)
TYPE OF
GAS
Characteristics
NATURAL GAS
20 mbar
VALUE = 37.78 MJ/m3
Ws - 50.7 MJ/ m3
LPG GAS
28-30/37 mbar
VALUE = 49.92 MJ/Kg
BURNER
Burner
Auxiliary
Semi-rapid
Rapid
Ultra-rapid
RAPID
(large)
POSITION
SEMI-RAPID
(medium)
AUXILIARY
(small)
ULTRA-RAPID
(double crown)
MAX
MIN
MAX
MIN
MAX
MIN
MAX
MIN
3.0
0.65
2.0
0.45
1.0
0.33
3.5
1.2
0.286
0.062
0.190
0.043
0.095
0.031
0.333
0.114
119
Adjust.
96
Adjust.
70
Adjust.
136
Adjust.
NOMINAL THERMAL
POWER
kW
2.8
0.65
2.0
0.45
1.0
0.33
3.5
1.2
NOMINAL FLOW
RATE
g/h
202
47
144
32
72
24
252
86
NOZZLE REFERENCE
1/100 mm
86
40
71
32
50
28
93
56
NOMINAL THERMAL
POWER
kW
NOMINAL FLOW
RATE
m3/h
NOZZLE REFERENCE
1/100 mm
Dia. Tap By-pass
1/100 mm
28
32
40
56
APPLIANCE CLASS: 3
APPLIANCE CATEGORY: II2H3+
APPLIANCE GAS SUPPLY:
Natural gas G20 / 20mbar
Aeration adjustment none
9
Important safety requirements
This hob must be installed in accordance with the Gas
Safety (Installation and Use) Regulations (Current Edition)
and the IEE Wiring Regulations (Current Edition).
Detailed recommendations are contained in the following
British Standards Codes Of Practice: B.S. 6172/ B.S.
5440, Part 2 and B.S. 6891 Current Editions.
The hob should not be installed in a bed sitting room
with a volume of less than 20 m3. If it is installed in a
room of volume less than 5 m3 an air vent of effective
area of 110 cm2 is required. If it is installed in a room of
volume between 5 m3 and 10 m3 an air vent of effective
area of 50 cm2 is required, while if the volume exceeds
11 m3 no air vent is required.
However, if the room has a door which opens directly to
the outside no air vent is required even if the volume is
between 5 m3 and 11 m3.
If there are other fuel burning appliances in the same
room, B.S. 5440 Part 2 Current Edition, should be
consulted to determine the requisite air vent requirements.
FITTING THE GAS HOB
WITHOUT A COOKER HOOD ABOVE
900 mm
700 mm
400 mm
20
400 mm
100
mm
FO 2540
FITTING THE GAS HOB
WITH A COOKER HOOD ABOVE
Location
The hob may be located in a kitchen, a kitchen/diner or
bed sitting room, but not in a bathroom, shower room or
garage.
A minimum distance of 20 mm. must be left between the
rear edge of the hob and the rear wall.
The minimum distance combustible material can be fitted
above the hob is 400 mm.
The minimum distance combustible material can be fitted
directly above the hob is 700 mm.
A minimum distance of 100 mm. must be left between
the side edges of the hob and any adjacent cabinets or
walls.
Please note that all the distances quoted in the diagramm
are intended from the hob top.
mm
900 mm
700 mm
400 mm
20
mm
400 mm
100
mm
FO 2541
Installation
IMPORTANT
This hob must be installed by qualified
personnel to the relevant British Standards.
Any gas installation must be carried out by a
registered CORGI installer.
The manufacturer will not accept liability, should
the above instructions or any of the other safety
instructions incorporated in this book be
ignored.
10
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is important
to remove any protective materials, which were
put on in the factory.
On the end of the shaft, which includes the GJ 1/2"
threaded elbow, adjustment is fixed so that the washer
is fitted between the components as shown in the
diagram. Screw the parts together without using excessive
force.
Fitting the hob to the worktop
Carry out the installation of the hob as follows (follow
also the instructions given on the “Assembly and cut
outlines” supplied with the appliance):
1)
measure the worktop for the exact positioning of
the hob;
2)
make the holes for the gas and electric pipe outlet
and the safety holes to block the hob to the worktop
(follow the instructions given on the “Assembly
and cut outlines” - see fig. 1);
3)
screw the traction pins supplied with the appliance
into the holes situated under the hob and adjust
their height (according to the worktop height);
4)
5)
3
3
1
place the hob on the worktop (paying attention to
insert the traction pins into the safety holes of the
worktop - fig. 1);
2
push the hob ahead towards the back of the
worktop, and fix it to the worktop (fig. 2).
2
1
Fig. 1
FO 2537
1 - Holes for the gas and electric pipe outlet
2 - Safety holes to block the hob to the
worktop
3 - Traction pins
80
MI
N
FO 2538
Fig. 2
11
Gas Connection
Connection to the gas supply should be with either rigid
or semi-rigid pipe, i.e. steel or copper.
Connection to the gas supply can be carried out on the
left or on the right of the hob connection pipe.
The connection should be suitable for connecting to RC
1/2 (1/2 BSP male thread).
When the final connection has been made, it is essential
that a thorough leak test is carried out on the hob and
installation.
Ensure that the main connection pipe does not exert
any strain on the hob.
It is important to install the elbow correctly, with
the shoulder on the end of the thread, fitted to the
hob connecting pipe.
Failure to ensure the correct assembly will cause
leakage of gas.
FO 0814
A) End of shaft with nut
B) Washer
C) Elbow
FO 0264
Electrical connections
Any electrical work required to install this hob
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
THIS HOB MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
This hob is designed to be connected to a 230-240V
50Hz AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this book.
The hob is supplied with a 3 core flexible supply cord
incorporating a 3amp plug fitted. In the event of having to
change the fuse, a 3amp ASTA approved (BS 1362) fuse
must be used.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue
- Neutral
Brown
- Live
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
F
12
the letter 'E' or the earth symbol
or coloured
green and yellow.
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N' or
coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
A cut off plug inserted into a 13 amp socket is a
seriuos safety (shock) hazard. Ensure that the cut
off plug is disposed of safely.
Permanent Connection
In the case of a permanent connection, it is necessary
that you install a double pole switch between the hob
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the current
electric regulations.
The switch must not break the yellow and green earth
cable at any point.
Ensure that the hob supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
FO 0390
Wiring Diagram
L
1
A
2
0
3
220/240
4
5
A. IGNITOR SWITCH
6
B
B. IGNITOR UNIT
N
Fault Finding
Preliminary Electrical Systems
Check
Blue
Green
Yellow
Earth Wire
Green/Yellow
START
Isolate appliance
and carry out:
A: Earth Continuity
check.
( )
E( )
FUSE
Brown
SOCKET
(face view)
PLUG (with cover
removed)
Neutral Wire
Blue
N
L
Blue
Brown
Green
Yellow
NO
YES
Carry out:
C: Polarity check.
Has inlet fuse blown?
YES
NO
Inlet wiring
faulty.
Rectify any
fault.
Carry out:
D: Resistance to
Earth check.
Electricity supply
should now be
satisfactory.
A. EARTH CONTINUITY CHECK - Appliance must be
electrically disconnected - meter set on W (Ohms) x
1 scale and adjust zero if necessary.
a) Test leads from any appliance earth point to earth
pin on plug. Resistance should be less than 0.1
ý (Ohm), check all earth wires for continuity and
all contacts are clean and tight.
B. INSULATION CHECK - Appliance electrically
disconnected, all switches ON.
a) meter set on W(Ohms) x 1 scale.
Test leads from L to N in appliance terminal block.
If meter reads «0» then there is a short circuit.
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
b) meter set on W (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter reads
less than × (infinity) there is a fault.
NOTE - Should it be found that the fuse has failed
but no fault is indicated - a detailed continuity check
(i.e. by disconnecting and checking each
component) is required to trace the faulty component.
It is possible that a fault could occur as a result of
local burning/arcing but no fault could be found under
test. However a detailed visual inspection should
reveal evidence of burning around the fault.
13
Ignition System / Gas Ignition
Ignitor does not spark
YES
Check gas supply at
burner
NO
Check plug top fuse
and replace if
necessary
Light burner manually
Check polarity and
earth continuity of
supply point
Check by pass simmer
adjusted
Check position of the
electrode
Check earth continuity
of appliance
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check continuity from ignition
switches connector to ignitor unit
Check continuity from the tip of
each electrode to the
terminals 1 to 4 on the ignitor
unit
Check for breaks in the
insulation
of the HT leads
Change the taps
ignition switches
Change the ignitor unit
14
Check fitting of burners
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
-
Turn the gas tap to the MAX position and ignite.
-
Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
Procedure:
F
Re-ignite the burner and set to MIN.
Remove the control knob.
To adjust, use a thin bladed screwdriver and turn
the adjustment screw (see diagram) until the flame
is steady and does not extinguish, when the knob
is turned from MIN to MAX. Repeat this procedure
for all burners.
Minimum adjustment screw
Pressure Testing
F
Remove left hand pan support and front left burner
cap and crown.
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another
burner.
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
Conversion from Natural Gas to
LPG
It is important to note that this model is designed for use
with natural gas but can be converted for use with butane
or propane gas providing the correct injectors are fitted.
The gas rate is adjusted to suit.
Method
•
•
•
•
Ensure that the gas taps are in the 'OFF' position
Isolate the hob from the electrical supply
Remove all pan supports, burner caps, rings, crowns
and control knobs.
With the aid of a 7mm box spanner the burner injectors
can then be unscrewed and replaced by the
appropriate LPG injectors.
TO ADJUST THE GAS RATE
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw, which is
located down the centre of the gas tap control shaft.
Upon completion stick the replacement rating plate on
the under side of the hob.
IMPORTANT
The replacement/conversion of the gas hob
should only be undertaken by a competent
person.
15
CUSTOMER CARE
Grafiche MDM - Forlì
Zanussi
55-77 High Street
Slough
Berkshire, SL1 1DZ
Tel: 08705 727727
© Electrolux Household Appliances Limited 2000
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are
sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
35683-4501
09/00