Zanussi ZU 9155 Specifications

REFRIGERATOR
ZU 9155
INSTRUCTION BOOKLET
2222681-37
CONTENTS
Instructions for the User
Instructions for the Installer
Important Safety Instructions
3
Technical Specifications
11
Description of the Appliance
4
Installation
11
Operation
4
Before use
Setting the temperature
Fresh food refrigeration
The door shelves
Normal Operating Sounds
4
4
5
5
5
Health and Safety Guidelines
6
Defrosting
6
Maintenance and Cleaning
7
Internal cleaning
External cleaning
Periodic cleaning
Changing the light bulb
When the appliance is not in use
7
7
7
8
8
Something Not Working?
8
Service and Spare Parts
9
Customer Care Department
9
Guarantee Conditions
Positioning
Electrical Connection
12
Building-in Instructions
13
Grid preparation
Door reversal
Building the appliance in under a worktop
Fitting the plinth
10
2
11
13
13
13
15
IMPORTANT SAFETY INSTRUCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings of these warnings contact the Customer Care Departement.
Prior to Installation
■
General Safety
■
Check the appliance for transport damage. Under
no circumstance should a damaged appliance be
installed. In the event of damage please contact
your retailer.
■
Installation
■
■
■
■
■
■
This appliance is heavy. Care should be taken
when moving it.
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Ensure that the appliance does not stand on the
electrical supply cable.
Important: if the supply cable is damaged, it must
be replaced by authorized service or qualified personnel using a special cable of the same type.
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the required
distance for ventilation, as stated in the installation instructions.
The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
■
■
■
During Use
■
■
■
■
■
The refrigerant isobutane (R600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
During transportation and installation of the appliance, be certain that none of the components of
the refrigerant circuit become damaged.
If the refrigerant circuit should become damaged:
- avoid open flames and sources of ignition.
- thoroughly ventilate the room in which the appliance is situated.
■
■
Before cleaning, always switch off the appliance
and disconnect from the electrical supply.
When unplugging always pull the plug from the
mains socket, do not pull on the cable.
Servicing
■
■
Child Safety
■
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs
only. It is not intended for commercial or industrial
use.
Containers with flammable gases or liquids can
leak at low temperatures. Do not store any containers with flammable materials, such as spray
cans, fire extinguisher refill cartridges etc. in the
refrigerator.
Maintenance and Cleaning
Refrigerant
■
This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging
must therefore only be carried out by authorised technicians.
Take utmost care when handling your appliance so as not to cause any damages to the
cooling unit with consequent possible fluid
leakages.
The appliance must not be located close to
radiators or boilers.
Avoid prolonged exposure of the appliance to
direct sunlight.
Do not use other electrical appliances (such
as ice cream makers) inside of refrigerating
appliances.
Do not allow children to tamper with the controls
or play with the product.
There is a risk of suffocation! Keep packaging
material away from children!
This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local Service
Force Centre.
At the end of the Appliance Life
■
■
3
When disposing of your appliance use an authorised disposal site.
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
DESCRIPTION OF THE APPLIANCE
➀
➁
➂
➃
➄
➅
➆
➇
Dairy compartment
Movable shelf
➀
Bottle storage shelf
➇
Airduct exit
Air inlet filter
➁
Salad bin
Storage shelves
➆
Thermostat control
➅
➄
➂
➃
OPERATION
Before use
Remove all securing tapes. Wash inside the appliance with lukewarm water and bicarbonate of soda (5
ml to 0.5 litre of water).
Do not use soap or detergent as the smell
may linger. Dry thoroughly.
Setting the temperature
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and one
«OFF» (O) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Turn the thermostat dial to the required position.
An intermediate position is usually the most suitable,
although the temperature will be affected by:
When altering the temperature setting, allow 24
hours for the temperature to stablise before making
further changes.
Important
During prolonged periods of abnormally
hot weather, if the thermostat is set on too
high a number, the cooling system may
operate continuously and the fridge cooling
plate may not defrost. Turning the knob to a
lower number will cause the automatic
defrosting to resume.
Room temperature
l How often the door is opened
l How much food is stored
l Position of the appliance
In determining the correct temperature control setting
all these factors have to be considered and some
experimentation may be necessary.
l
4
Fresh food refrigeration
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not cover the shelves with any protective material,
such as paper, cardboard or plastic, which may
obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb, chicken or poultry): wrap
in polythene bags and place on top of the salad bin.
Meat can only be stored safely in this way for one
or two days at the most.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad bin.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags, to exclude as much air as possible.
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
The walls of the refrigerator are equipped with runners so that shelves can be positioned as desired.
D040
The door shelves
Depending on your requirements, the movable storage shelf on the door can be moved sideways.
For more thorough cleaning, the top door shelf and
the bottle shelf can be removed by pulling them in the
directon of the arrows, then refitting them in position.
Normal Operating Sounds
You may hear faint gurgling or bubbling sounds when
the refrigerant is pumped through the coils or tubing
at the rear, to the cooling evaporator.
When the compressor is on, the refrigerant is being
pumped round, and you will hear a whirring sound or
pulsating noise from the compressor.
A thermostat controls the compressor, and you will
hear a faint ‘click’ when the thermostat cuts in and
out.
5
HEALTH AND SAFETY GUIDELINES
Because of consumer demand, preservatives have been removed from many pre-prepared foods.
This together with the changes in shopping habits to a once-a-week shop, mean that safe handling and
storage of food is even more important than ever.
The following tips should help you to ensure that
the food in your home is in as perfect condition
as possible.
■
Keep the time between buying chilled food and
placing it in your fridge as short as possible. Tests
showed that the temperature of 1 litre of orange
juice rose to 22°C in an hour between the supermarket and home. It then took 11 hours to get
down to 7°C in the refrigerator.
■
Never allow spillages to dry and harden.
■
Store eggs in the egg rack provided in the refrigerator door. Discard any broken or chipped eggs.
■
Regularly check the refrigerator door seal to
ensure that it is clean and free from debris.
■
Keep the refrigerator door closed as much as possible.
■
Always wash your hands with soapy water and
dry them with a clean towel before handling food.
■
Do not push food together too much, try to allow
air to circulate around each item.
■
■
Cool cooked food as quickly as possible but do
NOT place in the refrigerator until cool. (Leave
food in a cool place in order that it can then be
placed in the refrigerator as soon as possible).
Keep work surfaces clean and avoid cross contamination by not using the same work surface or
knife, without washing them thoroughly in
between.
■
Do NOT mix raw and cooked meat, they must be
in separate containers. Take care not to let the
meat juices drip onto other food. If the meat does
drip, remove everything and clean thoroughly.
■
Do not store food uncovered.
■
Remove suspect food from your refrigerator and
clean the interior (see “Maintenance and
Cleaning”).
DEFROSTING
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the
fridge, periodically clean the water discharge hole (F) situated under the salad
bins. Use the special cleaner provided (P)
which you will find already inserted into the
discharge hole.
P
S.I.011
6
F
MAINTENANCE AND CLEANING
Warning
Before any maintenance or cleaning work is
carried out, DISCONNECT the appliance from
the ELECTRICITY supply.
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging
must therefore only be carried out by authorised technicians.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND
LEAVE A STRONG SMELL.
Important
Do not use abrasive products.
Clean the drain hole of the water trough at regular
intervals and make sure that the drain hole is never
obstructed, so that the defrost water may flow freely.
External cleaning
2
The appliance is equipped with an air inlet filter (1)
and an air outlet duct (2) on the ventilation grid. Keep
clean to guarantee good ventilation and good working
order of the appliance.
The filter can be removed and washed with water, as
follows:
1. Pinch flaps (a) and (b) with fingers
2. Pull the filter down.
3. Pull the filter out.
To replace the filter reverse the process.
b
a
1
S.I.012
An accumulation of dust will affect the performance of
the appliance and cause excessive electricity consumption.
The structure of the appliance permits the cleaning of
the rear zone close to the wall, using a vacuum cleaner.
1. Remove the plinth (1), then the ventilation grid (2);
2. Carefully pull the air deflector out (3), checking that
there is no water left from the defrosting process.
3
S.I.013
7
2
1
Changing the light bulb
Should the interior light fail to work, first switch off the
appliance and disconnect from the electricity supply,
then replace the bulb as follows:
unscrew the light cover and then pull it outward by
pressing as shown in the figure.
Unscrew the bulb and replace it with a new 15 watt
bulb (available from your nearest Service Force
Centre).
Replace the light cover by sliding it into its original
position and replacing the screw.
D411
When the appliance is not in use
When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods
and clean the appliance, leaving the door ajar to prevent unpleasant smells.
SOMETHING NOT WORKING?
Before contacting your local Service Force Centre check the following points.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
Solution
No power to appliance
- Check there is power at the socket.
- Check there is not a power cut by checking the
household lights.
- Check the fuse has not blown.
The light does not come on
- Ensure that the bulb is correctly fitted.
- Replace the bulb if it has blown.
- Check the door light switch is not jammed.
The temperature in the appliance is too high
- Check the ambient temperature is within the appliances
operating limits of 10˚C to 32˚C.
- Check the thermostat control knob is turned to the
correct setting relative to ambient conditions.
The compressor runs continuosly
- Adjust the thermostat control knob to give correct
temperature control. See page 4.
- Check that the door is closed.
- Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
- Check that air ventilation is not obstructed.
Excessive frost and ice has built up
- Ensure the door is not left open.
- Check that nothing is preventing the door from closing.
- Is the door gasket intact and clean?
Noise
- Refer to normal operating sounds.
Water under the salad bin
- Check the drain hole is not blocked. (see Maintenance
and Cleaning).
If after the above checks, there is still a fault, call your local Service Force Centre. In-guarantee customers
should ensure that the above checks have been made as the engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
8
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact
your local Service Force Centre by telephoning:-
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance
(found on the rating plate)
5. The purchase date
08705 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre
and further information about Service Force, please
visit the website at www.serviceforce.co.uk
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls.
Before calling out an engineer, please ensure you
have read the details under the heading “Something
Not Working.”
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products,
please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
* calls to this number may be recorded for training
purposes.
9
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
■
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
■
The appliance has been used for normal domestic purposes only, and in accordance with the manufactuer's
instructions.
■
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorized by us.
■
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
■
Any appliance or defective part replaced shall become the Company's property.
■
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
■
Damage or calls resulting from transportation, improper use or neglect, thc replacement of any light bulbs or
removable parts of glass or plastic.
■
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
■
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
■
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
■
The guarantee starts from the date you first purchased your product.
■
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
■
This guarantee relates to you and cannot be transferred to another user.
■
Your new home is within European Community (EC) or European Free Trade Area.
■
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
■
The product is installed taking in account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Sweden
UK
Senlis
Nürnberg
Pordenone
Stockholm
Slough
+33
+49
+39
+46
+44
(0)
(0)
(0)
(0)
(0)
3 44 62 29 29
800 234 7378
0434 39 4700
8 672 53 90
1753 219897
10
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
Width
Depth
81,5
56
53,8
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
AVERAGE DAILY UNITS ELECTRICITY (*)
220-240 V / 50 Hz
70 W
0,50 kWh
GROSS CAPACITY
138 l
NET CAPACITY
135 l
cm
cm
cm
(*)This figure is based on standard test results in accordance with European Standard EN153. Actual consumption will depend on how the appliance is used and where it is located.
INSTALLATION
Warning
IF YOU ARE DISCARDING AN OLD APPLIANCE THAT HAS A LOCK OR CATCH ON THE
DOOR, YOU MUST ENSURE THAT IT IS
MADE UNUSABLE TO PREVENT YOUNG
CHILDREN BEING TRAPPED INSIDE.
Important
It must be possible to disconnect the appliance
from the mains power supply; the plug must
therefore be easily accessible after installation.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
under “Door reversal”.
Positioning
The appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located on the inside left of the appliance.
The following table shows which ambient temperature is correct for each climate classification.
SN
ST
+10°C to +32°C
+18°C to +38°C
The appliance should be located in a dry atmosphere, out of direct sunlight and away from continuous heat and extreme temperature, e.g. not next to a
boiler or radiator or in a very cold room e.g. an outhouse. If these temperatures are exceeded i.e.
warmer or colder, then the appliance may not operate
correctly.
For building-in and door reversal instructions please
refer to the relevant instructions on the following
pages.
11
ELECTRICAL CONNECTION
WARNING:
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the
appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
This appliance complies with the following
E.E.C. Directive:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and
subsequent amendments.
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent amendments.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of breakdown.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
If you fit your own plug, the colours of the wires in the
mains lead of your appliance, may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
, or coloured green and
yellow.
13 AMP. FUSE
13 AMP
GREEN & YELLOW
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
BROWN
BLUE
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
D207
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
A replacement cover/carrier must be obtained from
your local Service Force Centre.
12
CORD CLAMP
BUILDING-IN INSTRUCTIONS
Before carrying out any work, remove the plug from
the power socket.
Door reversal
The appliance must be unplugged before starting
work. To reverse the opening direction of the door,
proceed as follows:
Grid preparation
Remove the grid from the appliance pulling it towards
you by hand.
F1
F
1
B
G
3
Right door opening:
Remove the left side (A) of the grid cutting it from the
rear (see figure, a).
A
a
A
F1
F
2
S.I.003
1. remove the top hinge (1) taking care not to let the
door fall;
2. remove the bottom door hinge (2).
3. take out the plugs (3) from the holes (F) and reinsert them in the holes (F1) on the opposite side;
4. refit the upper hinge (1) on the opposite side, on
the bottom (position A);
5. refit the door on the pin of the hinge (1) in position
A;
6. insert the pin of the unscrewed bottom hinge (2) in
the upper hole (G) of the door, therefore fix the
hinge on the top in position B.
B
b
S.I.002
Left door opening:
Remove the right side (B) of the grid cutting it from
the rear (see figure, b).
Attention
After completion of the door reversing operation, check that the door gasket adheres to the
cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to
the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by
heating up the part involved with a normal
hairdryer on a low setting.
a
a
S.I.001
Building the appliance in under a
worktop
To reposition the grid on the appliance proceed as
follows:
Apply the grid to the base of the appliance by pushing the clasps (a) until they click.
The dimensions of the recessed installation area
must correspond
with those indicated in the figure.
60
0
The appliance
could be inserted
between two units
min
(a) or as an end
55
0
unit (b).
600
a
820 - 870
N.B. The grid is to be assembled after having fixed
the appliance in the niche with the brackets.
600
b
S.I.004
13
30
S.I.006
If the appliance is to be installed between two units
with a matching furniture door/support panel, the
door/panel must be fitted to the adjacent unit using
suitable hinges (not supplied) before the appliance is
installed.
UPPER
SUPER.
3. The appliance is equipped with adjustable support
feet. To adapt the appliance to the height of the
installation area (max 870 mm), screw in, or screw
out the feet situated at each bottom corner.
LOWER
INFER.
B
A
C
D
PR266
D326
4. Separate parts A, B, C, D as shown in the figure.
1. Fasten the side panel to the rear of the appliance
with the fixing brackets.
LOWER
INFER.
50mm
UPPER
SUPER.
A
E
E
20m
m
PR166
5. Place guide (A) on the inside part of the furniture
door, up and down as shown in the figure and
mark the position of external holes. After having
drilled holes, fix the guide with the screws supplied.
D319
2. Fasten the appliance to the worktop or the sides,
applying the sealing strip between the refrigerator
and adjacent cabinet using the fixing brackets (E).
14
A
B
C
D
PR33/2
PR167/1
6. Fix cover (C) on guide (A) until it clips into place.
9. Fix cover (D) on guide (B) until it clips into place.
Fitting the plinth
8mm
Important
For the efficient operation of the appliance, it is
important that the original ventilation grid is
used.
A
PR167
B
7. Open the appliance door and the furniture door at
90°. Insert the small square (B) into guide (A). Put
together the appliance door and the furniture door
and mark the holes as indicated in the figure.
Remove the squares and drill holes with Ø 2 mm
at 8 mm from the outer edge of the door. Place the
small square on the guide again and fix it with the
screws supplied.
S.I.007
For an opening height dimension A=820 mm and
a plinth height dimension a=100 mm, the plinth
may be fitted without adjustments. The same
applies to an opening height dimension B=870
mm and a plinth height dimension b=150 mm.
a = 100
b = 150
A = 820
B = 870
■
580
PR168
25
8. Should the lining up of the furniture door be necessary, use the clearance of slots.
At the end of operations, it is necessary to check if
the door of the furniture closes properly.
- 80
25
S.I.008
■
■
For plinth heights greater than a=100 mm, b=150
mm, a cut should be made in the plinth, 580 mm
wide, in the centre of the appliance position, leaving a remaining height of a=100 mm, b=150 mm.
Attach plinth to the kitchen units.
Important
The plinth must be positioned at a minimun
distance of 25 mm from the door.
15
© Electrolux Household Appliances Limited 2002