OWNER’S MANUAL - OPERATION/INSTALLATION INSTRUCTIONS

WINEGARD

®

RV Digital Satellite System with RS-1000 Antenna

Model RM-4610, no Digital Magic

TM

Elevation Sensor

Model RM-DM61 with Digital Magic

TM

Elevation Sensor

Model RM-DM55 with Digital Magic

TM

(No Power Supply)

Made in U.S.A.

INSTALL “FRONT” INSCRIBED

ON BASE TOWARD FRONT

OF VEHICLE!

Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601

319/754-0600 • FAX 319/754-0787 • www.winegard.com 2451070 Rev3 8/10

1

PARTS INCLUDED:

Reflector (dish)

Gasket

RS-1000 antenna

Interior parts

Mount/base assembly

Hardware

Models RM-DM61/DM55

Electronic elevation sensor

Models RM-4610/DM61

Power supply

FINDING THE SATELLITE

STEP 1. Step outside the vehicle and, using a compass, determine which direction is North. (Standing in or near the vehicle can give you an incorrect reading.)

The more accurately you determine North, the easier it will be to find the satellite(s).

STEP 2. Using satellite receiver, determine correct elevation for your location. See your receiver manual for setup information.

STEP 3. Press button on Winegard Digital Display wall plate. If the antenna is in travel position, the display will show LL for Low Limit. HL for High Limit will show when dish is in Up position.

STEP 4. Crank elevation handle to raise antenna. Stop cranking when readout displays the correct elevation for your location.

STEP 5. Rotate antenna VERY SLOWLY until correct satellite signal is acquired. NOTE: Rotate 3° and then stop. DO NOT rotate continuously, even if you are rotating slowly. If you notice the elevation angle has changed, it may be due to the following reasons: a. RV is not parked level.

b. Antenna system is mounted to a slightly sloped

RV roof. (This is not a problem.

When you have rotated the antenna so it is facing in approximately the right azimuth [compass direction], simply adjust to correct elevation and continue

searching for the satellite signal.)

Special notes: When you have detected the satellite signal, adjust the antenna up/down and left/right for the strongest signal your receiver displays. Because of differences in receivers and installation methods, you may find the elevation numbers, after peaking on the strongest signal, no longer match what the receiver recommended. This is normal. The elevation sensor should always get you close enough to find a signal to peak on. If display turns off while you’re searching, just push button for another minute of operation. After a little practice, most people can find the signal in 30 to

50 seconds.

TROUBLESHOOTING

• If digital display reads EE, check wiring and connection. If wiring and connections are not correct at installation, operation is affected.

• Remember to rotate antenna VERY SLOWLY until correct satellite signal is acquired.

DISPLAY CODES

HL .................. High Limit

LL .................. Low Limit

Lo .................. Battery Low

Er .................. Communication Error

— — .............. Initializing

NOTE: Initialization may take up to 5 seconds.

Based on 5 minutes a day of usage, standard new alkaline batteries should last 88 days.

2

OPERATION

TUNING ANTENNA FOR THE BEST PICTURE

STEP 1. Your receiver should indicate it is receiving a signal. To tune your antenna, slowly move the antenna left, then right, until you find the position with the highest signal strength. It is important to turn the antenna slowly. Because the signal is digital, it takes a few seconds for the receiver to lock on.

STEP 2. Place rotation clamp in the LOCK position.

This prevents the antenna from moving and losing signal.

STEP 3. Slowly raise, then lower the antenna until you have “peaked” the signal (found the strongest signal).

ELEVATION

14 - 16 o

17 - 19 o

20 - 22 o

23 - 25 o

26 - 29 o

30 - 32 o

33 - 35 o

36 - 38 o

39 - 42 o

43 - 45 o

46 - 48 o

49 - 51 o

52 - 54 o

55 - 57 o

58 - 61 o

62 - 64 o

65 -67°

68 - 70°

71-73°

TURNS CW

14

14-1/2

15

15-1/2

16

16-1/2

17

17-1/2

18

18-1/2

19

19-1/2

20

20-1/2

21

21-1/2

22

22-1/2

23

WATCHING OFF-AIR TV

To watch the area (local) television programming, use one of these options —

• Use an A-B switch between the receiver and antenna power supply.

• Use a video switch, Figure 1.

• Connect antenna output from power supply to TV

ANTENNA input on receiver, Figure 2. When you turn off the receiver, it automatically switches you to off-air.

LOWERING ANTENNA TO TRAVEL POSITION

STEP 1. Set rotation clamp to ROTATE position.

STEP 2. Fully rotate antenna counterclockwise until pointer on directional handle aligns with red screw on rotation clamp.

STEP 3. Turn elevating crank counterclockwise in

direction of “DOWN” arrow until resistance is met.

The number of turns will vary according to the elevation angle the antenna was set to.

STEP 4. Move rotation clamp to the LOCK position.

CAUTION: Under no circumstances lower the antenna to any position other than travel position!

Rev. 11/11/03

OPERATIONS DO’S AND DON’T’S

DO’S

1. Do check parking location for obstructions before raising antenna.

2. Do carefully raise, lower and rotate the antenna — if difficult, check for cause.

3. Do rotate slowly when searching for the satellite(s) and check fine tuning on TV set for proper adjustment.

4. Do lower antenna before moving vehicle.

5. Activate programming by calling programming provider for your receiver.

SUGGESTED SETUPS

FOR MULTIPLE TVS

FIGURE 1

DON’T’S

1.

Don’t move RV/Coach with the antenna in the UP position. This will VOID your warranty. This may also cause damage to your roof.

2. Don’t force the elevating crank up or down. Check for the cause.

3. Don’t rotate directional handle hard against stops.

4. Don’t apply paint on top of base plate or anywhere on the lift.

5. Don’t apply approved sealing compound on gear housing.

!

To order receivers or programming please call the Winegard receiver hotline: 1-(866) 609-9374.

FIGURE 2

3

Rev. 6/10

TROUBLE SHOOTING

NO PICTURE ON TV

1. Do you have a clear line of sight to the satellite? Are there trees, buildings, etc. in the way? Figure 3 illustrates the look angle of your reflector.

2. Do you have the menu from the receiver? If not, check the channel the TV set is tuned for — it should be 3 or 4.

3. Check connections at the receiver, TV and antenna.

NO SIGNAL FOUND

1. Have you entered the correct zip code into the receiver? If the zip code is wrong, you may be searching in the wrong direction or elevation for the satellite.

2. Is your TV working properly? Does it receive pictures from off-air stations or your VCR?

3. Re-tune system for the best picture, using procedure on page 2.

4. Inspect antenna. Has it been damaged? If it is even slightly bent, the receiver may not receive signal.

5. Do you have +12 VDC at the end of the LNBF cable?

Remove cable from LNBF before testing.

6. Contact your dealer or Winegard Technical Services at

800/788-4417.

ANTENNA IS HARD TO ROTATE, OR ANTENNA

DOES NOT ROTATE

1. Inspect antenna on roof. Make sure mount has not been damaged.

2. Be sure there is no sealant between gear housing and base plate.

4. Be sure cable is routed correctly. Cable may be preventing rotation of antenna.

3. Contact your dealer or Winegard Technical Services at

800/788-4417.

ANTENNAS HARD TO RAISE, OR ANTENNA DOES

NOT RAISE

1. Inspect antenna on roof. Be sure he mount has not been damaged.

2. Is the antenna obstructed?

3. Contact your dealer or Winegard Technical Services at

800/788-4417.

FIGURE 3

Reflector at 90°

Signal from satellite

24°look angle

LNBF

WARRANTY REPAIR WORK

Before you have warranty repairs on your system, be sure the company or individual doing the work has been approved by Winegard Company. If there is not an approved repair company/individual available, contact

Winegard Company at 800/288-8094 before proceeding.

The Winegard Warranty covers only the mount, antenna and LNBF. F or receiver warranty, refer to the receiver manufacturer’s warranty.

ORDERING REPAIR PARTS

Repair parts are available at RV dealers and/or service centers throughout the U.S. Or you can call Winegard

Company at 800/288-8094. Credit card orders only, minimum order $5.00.

4

INSTALLATION AND ASSEMBLY

THINGS YOU NEED

Screwdrivers (Phillips and slot)

1-3/4” hole saw

7/16” wrench

Drill with 1/8” bit

Tape measure

Sealant

(Must be approved for compatibility w/roof)

STEP 1. Choose a location on the roof for the unit. The dish must be able to rotate without interfering with other roofmounted equipment (air conditioners, etc.), Figure 4. Be sure the interior ceiling plate is easily accessible with no obstructions that may interfere with operation.

NOTE: Check with your dealer or vehicle manufacturer for features that may have been installed for

antenna mounting — reinforced roof areas or pre-wire installation done at the factory.

THE SYSTEM MUST BE LEVEL FOR PROPER OP-

ERATION! Winegard’s RW-5000 roof wedge is available for sloped roofs, Figure 5. If using roof wedge, installer will provide longer mounting screws.

Mount base plate and ceiling plate must be parallel with each other,

Figure 5. If shims or wedges are used, the installer must supply.

STEP 2. Position roof template (inserted in this manual) on the roof.

CAUTION: DO NOT drill through wiring.

Carefully drill a 1-3/4” hole through roof and ceiling of vehicle.

Inspect hole to make sure wiring is intact.

FIGURE 4

FIGURE 5

Mount base plate and ceiling plate must be parellel with each other. if shims or wedges are needed, installer must supply.

5

STEP 3. Remove backing from gasket. Attach adhesive side to base plate. IF YOU ARE USING

THE ROOF WEDGE (RW-5000), use 3/16” gasket included with the mount UNDER the roof wedge.

Install the 1/16” gasket included with

RW-5000 BETWEEN the mount and roof wedge.See Figure 7.

The word FRONT is embossed on the base. This MUST

FACE the front of the vehicle.

Secure to roof using two mounting screws provided. Check inside the vehicle.

PINS

E-CLIPS

Be sure the shaft is centered in the hole.

Attach crank handle to shaft.

Crank unit up until it stops.

Attach RS-1000 to

ELEVATING TUBES using

E-Clips and Pins supplied.

FIGURE 6

RS-1000 ANTENNA

(4) ANTENNA

MOUNTING BOLTS

REFLECTOR

(4) 1/4 - 20

HEX NUT

STEP 4. Attach reflector to backup assembly, Figure 6.

STEP 5. Attach RS-1000 antenna to elevating tubes.

Use the two E-clips and pins provided, Figure 6. Attach coax cable to F-jack on antenna and slide on weather boot, Figure 6.

STEP 6. Install remaining mount base screws. Install the vent tube on the back of the mount base. (This is the side opposite the word FRONT.) The hole for the vent tube is shown in Figure 8.

CAUTION: DO NOT seal hole in vent tube. Put sealant around the outside of the vent tube, approximately 1/2” from end, Figure 8. Push the vent tube into the hole. The sealant will seal the hole as you push in. Leave approximately 2 to 2-1/2” of the vent tube extending from the hole. Put a small amount of approved sealant on the roof and under the vent tube to hold in place.

FIGURE 7

Cable clamp

Do not attach cable clamp with screw to base plate until installing cable.

FIGURE 8

Cable-entry plate

Minimum 3” from mount base

Travel Bracket

6-1/8”

Base plate

6

STEP 7. Facing the front of the dish, find coax cables attached to side of the feed arm, Figure 9. Measure 24” of coax from this point and mark. DO NOT CUT. Rotate mount on base clockwise, fully, until it stops. Route coax around mount base, Figure 10.

Fasten cable clamp in hole in mount base (check roof template inserted in this manual for correct location) at end of the coax cable measurement.

FIGURE 9

Measure coax

24” from plastic tie wrap on left side of feed arm. (STEP 7)

FIGURE 10

STEP 8. Feed coax cables through the roof. Weather-

proof cable entry by applying sealant under the lip of the cable-entry plate and where cable enters roof. Attach plate to roof with screws provided. Apply sealant over screws and around edge of roof-through plate, making sure cable entry is sealed. Secure cables as necessary to prevent whipping.

If cable connections are exposed, be sure to weatherproof connection!

Mount travel bracket to roof 6-1/8” from base, Figure

7, page 6.

STEP 9. Apply approved sealing compound to screw heads, cable entrance hole and edge of gasket under mount, AFTER mounting, Figure 7.

STEP 10. Attach satellite coax cable (with RG-6 printed on it) to the satellite receiver.

STEP 11. Attach RS-1000 coax downlead (with RG-59 printed on it) to RV-7542 power supply. Refer to power supply instruction sheet. You can connect the antenna

ANOTHER METHOD OF INSTALLING ROOF CABLE/

ENTRY PLATE: Attach cable to roof using cable clamp.

Use sealant to seal screw heads.

Cable clamp

Cable

Cable entry plate

7 output from the power spply directly to the “TV ANT IN” on satellite receiver. (Refer to receiver manual.) This allows you to watch local channels when you turn off the receiver.

STEP 12. Connect digital elevation sensor at roof level, see top of page 8.

FOR RM-DM61/RM-DM55 ONLY

DIGITAL ELEVATION SENSOR ROOF CONNECTIONS

The illustrations below show the different methods of connecting wires at roof level. Method will depend on model. Wire colors MUST MATCH (i.e. red to red, green to green, black to black, white to white).

Supplied with the DM-2000 only.

This wire harness connects to the digital elevation sensor on the antenna.

3M UR Terminal

Squeeze pliers until red plunger is flush with rest of terminal.

Snap connectors together

NOTE: This terminal is NOT weatherproof and CANNOT be left outside on the roof.

Slide wires all the way in.

DO NOT strip wires, terminal is self stripping.

Pliers not supplied

NOTE: This terminal is weatherproof and can be left outside on the roof as LONG AS IT IS SECURED PROPERLY to prevent whipping in the wind.

FIGURE 11

INSIDE YOUR RV

STEP 13. Place the nut on the threaded rod.

STEP 14. Measure and cut the threaded rod with a hacksaw. Use the chart, Figure 11, to determine the length.

STEP 15. Remove the nut over the cut end of the threaded rod. This cleans the threads after cutting.

STEP 16. Thread the cut end of the rod into the hub,

STEP 17. Install the ceiling plate. The rotate/lock lever must point toward the rear of the vehicle.

Be sure rotate/lock lever is pointing toward back of vehicle and hole in ceiling aligns with hole in the ceiling plate.

NOTE: Make sure large and small keyways line up in the hub and directional handle!

STEP 18. Measure and cut the directional handle; see Figure 12 and chart, Figure 11. NOTE: A tube cutter is recommended for cutting the directional handle. This gives a square cut; a hacksaw does not.

If using an extension, see Step 22, page 9.

Figure 13, page 9, shows what points to measure between, with and without a roof wedge.

FIGURE 12

DIRECTIONAL

HANDLE

HANDLE

LENGTH

Roof

Thickness

Directional

Handle Length

(Figure 3E)

Threaded

Rod Length

Worm Gear

Shaft Length

(Figure 3G)

1-1/2” ...............2-7/8” ................. 2-3/4” ............... 2-7/8”

1-3/4” ...............3-1/4” ................. 3” ..................... 3-1/8”

2” .....................3-1/2” ................. 3-1/4” ............... 3-1/2”

2-1/4” ...............3-7/8 .................. 3-1/2” ............... 3-7/8”

2-1/2” ...............4-1/8” ................. 3-3/4” ............... 4-1/8”

2-3/4” ...............4-1/2” ................. 4” ..................... 4-1/2”

3” .....................4-3/4” ................. 4-1/4” ............... 4-3/4”

3-1/4” ...............5” ....................... 4-5/8” ............... 4-7/8”

3-1/2” ...............5-1/4” ................. 4-7/8” ............... 5-1/8”

3-3/4” ...............5-5/8” ................. 5-1/4” ............... 5-1/2”

4” .....................5-3/4” ................. 5-1/2” ............... 5-3/4”

4-1/4” ...............6-1/8” ................. 5-3/4” ............... 6-1/8”

4-1/2 ................6-1/2 .................. 6” ..................... 6-1/4

4-3/4” ...............6-5/8” ................. 6-1/8” ............... 6-3/8”

5” .....................6-7/8” ................. 6-3/8” ............... 6-5/8”

5-1/4” ...............7-1/8” ................. 6-5/8” ............... 7”

5-1/2” ...............7-3/8” ................. 6-7/8” ............... 7-1/4”

5-3/4” ...............7-5/8” ................. 7-1/4” ............... 7-1/2”

6” .....................7-7/8” ................. 7-1/2” ............... 7-3/4”

6-1/4” ...............8-1/8” ................. 7” ..................... 8”

6-1/2 ................8-1/2 .................. 7-3/4” ............... 8-1/4

6-3/4” ...............8-3/4” ................. 8” ..................... 8-1/2”

7” .....................9” ....................... 8-1/4 ................ 8-7/8”

7-1/4” ...............9-3/8” ................. 8-5/8” ............... 9-1/8”

7-1/2 ................9-5/8” ................. 8-7/8” ............... 9-3/8”

7-3/4” ...............9-7/8” ................. 9-1/8” ............... 9-5/8”

8” .....................10-1/8” ............... 9-3/8” ............... 10”6-1/4”

8-1/4” ...............10-3/8” ............... 9-5/8” ............... 10-1/4”

8-1/2 ................10-3/4” ............... 9-7/8” ............... 10-3/8”

8-3/4” ...............11” ...................... 10” ................... 10-5/8”

9” .....................11-1/4” ................ 10-1/4 .............. 11”

9-1/4” ...............11-1/2” ................ 10-5/8” ............. 11-1/4”

9-1/2 ................11-3/4” ................ 10-7/8” ............. 11-1/2”

9-3/4” ...............12” ..................... 11-1/8” ............. 11-3/4”

10” ...................12-3/8” ............... 11-3/8” ............. 12”

10-1/4” .............12-5/8” ............... 11-5/8” ............. 12-1/4”

10-1/2” .............12-7/8” ............... 11-7/8” ............. 12-1/2”

8

Rev. 9/24/04

STEP 19. The directional handle and threaded rod will fit roofs up to

5-1/4" thick. If you are using wedges to compensate for roof/ ceiling slope, be sure to allow for this extra thickness. You may add an extension to the directional handle for thicker roofs. Each extension will increase the length of the directional handle by 2-1/4".

WITH ROOF WEDGE

Measure from top of roof wedge to ceiling.

TOP OF

ROOF WEDGE

TOP OF

ROOF

WITHOUT ROOF

WEDGE

Measure from top of roof to ceiling.

FIGURE 13

CEILING CEILING

FIGURE 14

Plastic

Plug

Spacer

Spring

Worm

Gear

Threaded

Rod

Hub

STEP 20. Press the directional handle onto the hub. Point the arrow on the directional handle towards the rotate/lock lever to orient to the splines.

STEP 21. Install the washer and nut on the threaded rod. Tighten the nut enough to snug the directional handle to the hub.

STEP 22. IF YOU ARE USING AN EXTEN-

SION, adjust the total length of the directional handle and extension by cutting the directional

handle. After adjusting parts for proper roof thickness, glue the extension to the directional handle. Use ABS (plastic pipe) glue.

NOTE: For roofs thicker that 5-1/4", a longer aluminum hex shaft will be needed. Contact

Winegard Company for this part.

Ceiling

Plate

Directional

Handle

FIGURE 14A

CUTTING SHAFT

LENGTH, Figure 14A:

Flip down handle on the elevating crank handle.

Slide elevating crank handle up shaft until snug against directional handle. Mark the elevating shaft at inside bottom surface of crank handle housing, Figure 12. Cut shaft at mark, after removing crank handle.

Reinstall crank.

Elevating shaft

Cut elevating shaft at inside surface of crank handle housing; shaft goes through hex-shaped opening by screw.

Crank Handle

STEP 23. Check system for proper operation. Elevate dish with crank handle. A minimum of 14 turns is needed to elevate dish. Then, move directional handle with dish elevated. Directional handle should turn freely. If possible, have someone watch to make sure coax does not bind or interfere with dish movement.

9

CAUTION: After INITIAL

INSTALLATION, the antenna should ROTATE

APPROXIMATELY 360°

FROM TRAVEL POSITION.

The pointer on the

DIRECTIONAL HANDLE should point towards the

RED SCREW on the

ROTATION CLAMP when in TRAVEL POSITION.

ASSEMBLED VIEW

FIGURE 15

250

240

290

300

310

320

330

H

340 350

ORT

INT N PO

10

20

30

40

50

60

70

POINTER

MUST POINT

TO RED

SCREW ON

ROTATION

CLAMP

WHEN IN

TRAVEL

POSITION

POINT TO

BACK OF RV

Rotation

Clamp

Red Screw

CAUTION:

The antenna MUST BE IN THE

TRAVEL POSITION before

ALIGNING the Directional

Handle and Ceiling Plate.

Tighten screw snugly

Flat Washer

Nut for

threaded tube

10

Elevating Shaft

Threaded Tube

3 Directional

Handle Extension

1 Ceiling Plate

2 (4) #10 Phillips Flat

Head Screws

4 Directional

Handle

ALIGN POINTER

WITH ANTENNA

TRAVEL POSITION

5 ELEVATING

CRANK

HANDLE

(When installed, extends 2-1/4" from ceiling).

Snap Handle into base when not in use.

Rev. 6/10

EXPLODED PARTS VIEW

Adapter Rubber Bumper

11

PARTS LIST

INTERIOR

HARDWARE KIT

RK-CEIL

Directional

Handle

Extension

Ceiling Base

Directional Dial

(4) #10 Phillips Flat

Head Screws

Azimuth Lock

Azimuth Lock Knob

Washer

#10 x 3/8"

Red Phillips

Screw

Directional Handle

CRANK HANDLE KIT

RK-HAND

#8-32 x 3/8"

Phillips Screw

#8-32 Square Nut

#10 x 3/8" Phillips Screw

Crank Handle Base

Crank Handle

Knob

Washer

NOT TO SCALE

Rev 6/11/01

12

SPECIFICATIONS

Height when raised ........ 30” with satellite antenna in vertical position

Height in travel position ........ 8”

Operating radius ........ 35” (70” diameter circle)

Roof space required ........ 19.5” x 46.75”

LNBF ........ Compatible with DISH Network ® , DirecTV ® and ExpressVu

Color ........ White

Satellite antenna height ........ 20.9”

Satellite antenna width ........ 19.5”

F/D ........ 0.59

Offset angle ........ 24°

Satellite antenna gain—

11.2 GHz ........ 33.22 dBi

12.1 GHz ........ 33.89 dBi

12.6 GHz ........ 34.23 dBi

Aperture efficiency ........ 73%

Cross polarization (on axis) ........ -21 dB

*Beamwidth at -3 dB ........ 3.5°

*Beamwidth at -10 dB ........ 7.0°

RS-1000 antenna gain —

VHF ........ 15.5 dB average

UHF ........ 19.5 dB average

RS-1000 antenna height ........ 3.25”

RS-1000 antenna width ........ 14.5”

Wind Loading ........ Up to hurricane force

Weight ........ 19 lbs. maximum

Shipping weight ........ 21 lbs.

13

REPLACEMENT PARTS KITS

HEAD ASSEMBLY RP-RS00

Head w/bracket and nut ................ 1

Pins .............................................. 2

E-Clip ............................................ 2

REFLECTOR RP-REFL

Dish .............................................. 1

Bolt ............................................... 4

Nut ................................................ 4

BOOM ASSEMBLY RP-BOOM

Top boom ...................................... 1

Bottom boom ................................ 1

Bumper ......................................... 1

Screw ............................................ 1

Bushing ......................................... 1

Lift link .......................................... 2

Pin ................................................ 3

E-Clip ............................................ 4

Nut ................................................ 2

Screw ............................................ 1

Pivot bracket ................................. 1

Long bolt ....................................... 1

Nylock nuts ................................... 2

BACKUP & FEED ASSEMBLY RP-BUFA

Fram ............................................. 1

Feed arm ....................................... 1

Roller ............................................. 1

Bolt ............................................... 1

Nut ................................................ 3

Bracket ......................................... 1

Pin ................................................ 2

E-Clip ............................................ 3

Screw ............................................ 1

Spring ............................................ 1

Clamp ............................................ 1

Screw ............................................ 4

TURRET ASSEMBLY RP-9500

Spring ............................................ 1

Roll Pin ......................................... 1

Gear for worm shaft ...................... 1

Elevation gear ............................... 1

Bushing ......................................... 2

Seal .............................................. 2

O-ring ............................................ 1

Clamp ............................................ 2

Shaft ............................................. 1

Bearing, outer ............................... 1

Bearing, inner ................................ 1

Worm gear on shaft ....................... 1

Turret top ...................................... 1

Turret base .................................... 1

Turret hub ..................................... 1

Plug .............................................. 1

Plate rotate limit ............................ 1

Screw ............................................ 2

Gasket .......................................... 1

Bracket ......................................... 1

Screw ............................................ 2

Pin ................................................ 2

E-Clip ............................................ 2

Pivot Bracket ................................ 1

GEAR KIT RP-GEAR

Elevation gear (RMs) ..................... 1

RD MODELS

Elevation gear (RVs & RDs) .......... 1

Plug .............................................. 1

O-ring ............................................ 1

Wave washer ................................ 1

Quad ring ...................................... 1

Flat washer ................................... 1

Washer .......................................... 1

Extension ...................................... 1

Worm gear, 16” shaft ..................... 1

Seal .............................................. 2

Bushing ......................................... 2

14

15

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchase to an authorized Winegard dealer (to locate the nearest authorized

Winegard dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone 800-288-8094 or visit www.winegard.com). Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty. If the date of purchase cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service. Customer must provide proof of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard dealer for service prior to expiration of year one (1) of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services, Winegard Company will cover the Winegard dealer’s labor charges for warranty service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of the service.

Approval of the service is at the sole discretion of Winegard Company.

Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3111 Kirkwood Street,

Burlington, Iowa 52601, Telephone 800-788-4417). Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Customer’s name, address, and phone number. Customer must also provide proof of purchase to verify the product is under warranty. If the product is returned before the expiration of the warranty period, Winegard Company will (at its option) either repair or replace the product.

This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation, misuse, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard in any manner whatsoever, removing or defacing any serial number, usage not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain.

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard

Warranty Services under this warranty policy. Please call our Technical Services Department at 800-788-4417 or send an email to [email protected]

to obtain the RMA number. Please furnish the date of purchase when requesting an RMA number. Enclose the product in a prepaid package and write the RMA number in large, clear letters on the outside of the package. To avoid confusion or misunderstanding, a shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and returned to Customer freight collect.

WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED,

MADE BY ANY OTHER PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS

FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.

In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the above limitations or exclusions do not apply.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state.

SATELLITE RECEIVER WARRANTY:

See manufacturer’s limited warranty policy.

Rev. 2/08

Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601 © Winegard Company, 2003, 2005 2451070 Rev3 8/10

16