Extron electronic DSC HD-3G A Switch Setup guide

DSC HD-3G A Scaler • Setup Guide

The Extron DSC HD-3G A is an HDMI to 3G-SDI scaler that converts HDMI signals to 3G-SDI, HD-SDI, and SD-SDI. It accepts computer and SMPTE video resolutions up to 1920x1200 and 2k, and offers multiple output rates from 480i up to HDTV

1080p @ 60 Hz and 2k. The DSC HD-3G A features advanced Extron video signal processing with 1080i deinterlacing and Deep

Color processing for optimal image quality. Dual SDI outputs, stereo audio embedding, and genlock are also provided.

This setup guide provides step-by-step instructions for an experienced user to set up and configure a DSC HD-3G A. It covers how to perform basic operations using the front panel controls and selected Simple Instruction Set (SIS ™ ) commands.

NOTE: For full installation, configuration, menus, connector wiring, and operation details, see the DSC 3G-HD A and

DSC HD-3G A User Guide, available at www.extron.com

.

Installation

Rear Panel Features

100-240V ~ .3A MAX

50-60 Hz

L

AUDIO

R

INPUT

HDMI

SYNC

GENLOCK

OUTPUT

3G/HD/SD-SDI

REMOTE

RS-232

Tx Rx G a AC power connector b 5-pole captive screw audio input

connector c HDMI video input connector d Genlock sync connectors e 3G/HD/SD-HDI output connectors f 3-pole RS-232 captive screw

connector

1 2 3 4 5 6

Mounting and Cabling the DSC HD-3G A

1. Disconnect power: Turn off or disconnect all equipment power sources.

2. Mount the unit: (Optional) Mount the DSC HD-3G A either in a rack using shelf mounting brackets (RSU 129 or RSB 129) or under furniture using furniture mounting brackets (MBU 125) (see figures 1 and 2 at right). A false face plate (RFF 052) can be fitted on top of the low profile DSC if desired.

3.

4.

Connect the input: Connect an HDMI video source to the HDMI input connector c .

Connect analog audio input: (Optional) Connect analog audio from the source to the captive screw Audio input connector b .

NOTE: To embed audio from this input, you must first set it up using the

on-screen display

(OSD) (see page 2) or

SIS commands (see

page 4).

Half-rack false front panel uses 2 front holes.

DIG

ITAL

DVC 501 SD

VID

EO CONV

ERT

ER

(2) 4-40 x 3/16" screws

Use 2 mounting holes on opposite corners.

Figure 1. Rack Mounting

5.

6.

7.

Connect the output: Connect one or two SDI display devices to the 3G/HD/SD-SDI output connectors embedded analog or HDMI audio. e for SDI output with optional

Connect a control device: For remote control via SIS commands or the PCS Windows ® -based control software: z z

RS-232 — For serial RS-232 control, connect a host computer or control system to the 3-pole captive screw RS-232 connector f .

RS-232 protocol (default values) are 9600 baud, 1 stop bit, no parity, 8 data bits, no flow control.

USB — Connect a host computer or control system to the front panel mini USB port ( b in the front panel illustration on page 2) for configuration and control via Extron PCS Control software.

AC power connector — Connect the supplied US standard IEC power cord between this connector a and a 110-220 V 50-60 Hz AC power source.

Mounting

Screws

(2) Places

Each Side

#8 Screw

(4) Places

Each Side

MBU 125 Mounting Bracket

Figure 2. Under-furniture Mounting

1

DSC HD-3G A • Setup Guide (Continued)

Front Panel Overview

Extron

CONFIG

INPUT

SIGNAL

2CH-LPCM

MULTI-CH PCM

ANALOG

OUTPUT

SYNC

2.97 Gbps

1.485 Gbps

270 Mbps

MENU

DSC HD-3G A

ENTER HOLD FOR 720p 1080i

AUTO-

IMAGE

2

1 2 3 4 5 6 a

Status LED — Lights steadily amber when there is power but no signal, blinks amber every 3 seconds when the unit is in standby mode, and lights steadily green when both power and an input signal are present. b

USB configuration port — Connect a control system or computer to this mini USB port (cable not supplied) for device configuration, control, and firmware upgrading. c

Input LEDs — The Signal LED lights to indicate presence of an input signal. An audio signal LED (2CH-LPCM, Multi-CH

PCM, or Analog) lights to indicate the type of audio signal (two-channel LPCM, multi-channel PCM, or analog) if present. d

Output LEDs — Light to indicate the presence of sync and the rate specified for the output: z

Sync: Sync is present (does not light if video sync is muted).

z z z

2.97 Gbps: SMPTE 424M

1.485 Gbps: SMPTE 292M

270 Mbps: SMPTE 259M e

Menu and Enter buttons — Let you access the OSD and select submenus and options from the menus.

f

Navigation buttons — Press these right , left , up  , and down



arrow buttons to step through the OSD submenus, to lock the front panel (see the next section), perform Auto-Image (press ), and reset the output rate (hold



for 5 seconds).

Locking the Front Panel (Executive Mode)

To prevent unauthorized access or accidental changes to DSC settings, you can lock the front panel controls, making control available only by SIS commands. (The default state is unlocked.) You can lock and unlock the front panel as follows: z z

Using the front panel buttons: To lock, press the Menu and



buttons simultaneously and hold them until the OSD displays Executive Mode Enabled (approximately 5 seconds). To unlock, repeat this process.

SIS commands: To lock (enable executive mode), enter 1X. To unlock (disable executive mode), enter 0X.

Configuring the DSC HD-3G A

The DSC HD-3G A can be configured through a host connected to the RS-232 or USB port, using Extron PCS Windows-based control software (available at no charge at www.extron.com

) or

SIS commands (see page 4 for a selection of basic commands). You

can also configure it using the OSD menu system, described below.

On-Screen Display (OSD) Menu System

The OSD menu system consists of seven submenus and two information screens. To access the menus, press the front panel

Menu button. With the main menu displayed, use the arrow buttons to step through the submenus and submenu options. Press the

Enter button to select items that you highlight. Communication and

Device Info screens are read-only and do not provide selections.

• Quick Setup • User Presets • Picture Controls

• Input

• Advanced

•

•

Output

Communication

•

•

Audio

Device Info.

NOTE: The OSD times out and closes after 1 minute if no buttons are pressed.

To use any menu:

1. Press the Menu button to access the main menu. The menu opens with the Quick Setup menu displayed.

2. Press the  and



buttons repeatedly to cycle through to the desired submenu (each button press outlines the next option).

3. Press the Enter button to access the desired submenu. The first option is outlined in yellow.

4. Press the  and



buttons to cycle through the options of the selected submenu until the desired item is outlined.

5. Press the Enter button to select the outlined option (the selected option is highlighted).

6. Press the  and  buttons to adjust the values within the option. For the options on the Picture Controls submenu, press the right or left arrow button to select the sub-option on the right or left, then press the  and



buttons to adjust the settings.

7. Press the Enter button to confirm your new values. The yellow highlighting is replaced by the yellow outline on the submenu screen.

8. Press the  or



to move to another submenu option or press the Menu button to exit the submenu. To exit the menu system, press the Menu button twice.

Setting Up the DSC HD-3G A Using the OSD Menu

The Quick Setup submenu is displayed when the OSD opens. This submenu contains options from other submenus that you are most likely to need when configuring the DSC for the first time. Use the Quick Setup submenu to perform a basic system setup and get started quickly using the DSC. Select the following options from it as needed: z z z z z z z

Auto-Image™ — Performs an Auto-Image on the video input to adjust the horizontal and vertical size and positioning to the selected aspect ratio (fill the screen or follow the input device aspect ratio). To perform an Auto-Image, select this option, then press Enter again to initiate the Auto-Image.

Input EDID — Matches the input EDID to the output rate or sets a discrete EDID. After selecting Input EDID, press the  or

 button to step through the available EDIDs (the default is 720p @ 59.94 Hz).

Output Resolution — Lets you select the resolution and refresh rate for the current output from 42 available factory-installed rates (see "Output Scaler Rates"). Select the Output Resolution submenu, then press the buttons to cycle through the available rates.

 and



Auto Memory — Sets the DSC to automatically save the current input configuration and picture control values according to the most recent configuration for each different rate. After selecting Auto Memory, press any arrow button to toggle Auto

Memories on and off.

Aspect Ratio — Lets you specify how much of the display the image fills. The sub-options are Fill (fills the entire screen) or Follow (uses the aspect ratio of the input). After selecting Aspect Ratio, press any arrow button to toggle between

Fill and Follow.

Input Audio Format — Lets you select the format of the audio to embed in the output. After selecting Input Audio

Format, press any arrow button to cycle through the options: None (mute the audio), Analog (embed analog audio onto the

SDI output), LPCM2CH (use the first channel pair), Multi-Ch (use the first four channel pairs).

Test Pattern — Lets you select from seven test patterns to aid in setting up the DSC and the output display.

Output Scaler Rates

Output rates can be set using the OSD menu or SIS commands. The table below gives the rates and their SIS variables (see

page 4 for the commands ).

SIS Variables for DSC HD-3G A Resolutions and Refresh Rates (X2) = 65 through 96)

Resolution 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz

65 66 480i

576i

720p

1080i

95

1080p

2048x1080 (2k)

77

85

*Default output resolution

96

78

86

68

79

87

69

80

88

70

81

89

67

71

74

82

90

72*

75

83

91

73

76

84

92

Output Rate Reset

If an image cannot be displayed due to an incompatible output rate, you can reset the output rate as follows:

With the OSD closed, press and hold the  button for approximately 5 seconds to toggle between 1080i @ 59.94 Hz and

720p @ 59.94 Hz.

3

DSC HD-3G A • Setup Guide (Continued)

Basic SIS Commands

The DSC HD-3G A can be configured with specific SIS commands via RS-232 or USB connection. This table lists a selection of basic commands. For a full list of SIS commands and variables see the DSC HD-3G A and DSC HD-3G A User Guide, online at www.extron.com

.

Command

View input video format

ASCII Command

(host to Scaler)

1 * \

Response

(Scaler to Host)

Vtype 1 * X# ]

Additional Description

View detected input video format X# .

Audio Input Format — select between analog (5-pole captive screw connector) and digital (embedded in HDMI input) audio sources.

Set to none

Set to analog

E I 1 * 0 AFMT } Afmt I 1 * 0 ]

E I 1 * 1 AFMT } Afmt I 1 * 1 ]

Mute all audio for the input.

Select analog audio for the input.

Set to LPCM-2CH digital Select LPCM 2-channel digital audio for the input (default).

Set to Multi-CH digital

Execute Auto-Image

E I 1 * 2 AFMT } Afmt I 1 * 2 ]

E I 1 * 3 AFMT } Afmt I 1 * 3 ]

A Img ]

Select multi-channel digital audio for the input.

Perform an Auto-Image on the current input.

Output Configuration

Set output scaler rate

View output rate

E

E

X2) RATE

RATE }

} RATE

X2) ]

X2) ] Select output resolution and refresh rate

output SIS variables table

on page 3).

X2) (see the

Show the current output rate for the DSC HD-3G A.

Video Mute (Defaults to unmuted after a power cycle.)

Mute video to black

Mute video and output sync

View video mute status

1 * 1B

1 * 2B

1B

Vmt 1 * 1 ]

Vmt 1 * 2 ]

X4@ ]

Screen Saver Mode (Takes place when no signal is detected on the input.)

Set screen saver mode E M X4) SSAV } Ssav M X4) ]

Mute the video and display a black screen.

Mute all TMDS signals on the HDMI video output.

View output video mute status ( X4@ ).

Set the screen saver mode to X4) (default = 1 = black).

View screen saver mode

Set sync timeout duration

View sync timeout duration

View screen saver status

Reset device to factory settings

Power Save Mode

Power save off

Power save on

View power save setting

E M SSAV }

E T X2* SSAV }

E

E

E

E

E

E

T SSAV

S SSAV

ZXXX

PSAV

}

0 PSAV

}

}

}

1 PSAV }

}

X4) ]

Ssav T X2* ]

X2*

X6#

Zpx

Psav 0 ]

Psav 1 ]

X6@

]

]

]

]

View current screen saver mode X4) .

Set the period before sync timeout to

(default = 501 = never).

X2* seconds

View the amount of time X2* before sync timeout.

View the screen saver status X6# .

Resets all device settings to the factory defaults.

Set the DSC to run in full power mode (default).

Place the DSC in low power mode). (This mode can be exited only via the E 0 PSAV } command

View power save status X6@ .

NOTE: X# = Input video format: 0 = no signal; 1 = HDMI, 2 = DVI, 3 = invalid signal (up to 30 Hz);

4 = 3G-SDI 1080p (@ 50, 59.94, and 60 Hz), 2k; 5 = unknown.

X2) = Output scaler rate: 0 = match output rate, 1 = custom rate 1, 2 = custom rate 2, 3 = custom rate 3,

9 = match input (see the resolution and refresh rate table

on page 3 for more rate variables).

X2* = Output sync timeout duration in seconds ( 1-500 in 1-second increments): 501 = never (default), 0 = immediate timeout

X4) = Screen saver mode: 1 = black (default), 2 = blue

X4@ = Video mute: 0 = off (unmute), 1 = on (mute to black screen), 2 = on (mute all output sync and video)

X6@ = Power save setting: 0 = full power (default), 1 = low power state

X6# = Screen saver status: 0 = active, timer not running; 1 = no active input, timer running, output sync active;

2 = No active input, timer expired

4

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron Europe

+31.33.453.4040

Extron Asia

+65.6383.4400

Extron Japan

+81.3.3511.7655

Extron China

+86.21.3760.1568

Extron Middle East

+971.4.2991800

Extron Korea

+82.2.3444.1571

Extron India

+91.80.3055.3777

© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com

68-2261-50 Rev. A

10 13