All-Power APW5004 Owner's Manual

www.alJ ioweramerlca.com

RAVE OUESTIONS OR REED SERVICE

DO NOT RETURN TO STORE!

Canada: 866.882.8088

1800 PSI Pressure Washer

Table Of Contents

Topic

Important Safety

Tips, Precautions, Warnings, and Usage Instructions

Assembly Instructions

Operating Instructions

Detergents

Clean-up and Storage

Cleaning Tips

Technical Data

Troubleshooting Tips

Limited Warranty

Parts

Page #

2-5

6-8

9-12

12-13

14-15

16

17

18

19-20

21-22

1800 PSI Pressure Washer

GROUNDFAULTCIRCUITINTERRUPTER

(GFCI)

This pressure washer is provided with a ground fault circuit interrupter (GFCI)built into the plug of the power supply cord. This device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCIprotection.

This unit is equipped with a Ground Fault Circuit Interrupter (GFCI). When connecting the GFCIto the receptacle, the indicator should appear red. If the indicator is not red, depress the RESETbutton on the GFCIuntil the indicator appears red. If the indicator does not appear red, please see Section titled "Troubleshooting" for more information.

IMPORTANTSAFETYTIPS

Never

pointthe high-pressurenozzleat peopleor animals.

Never drink alcoholor usedrugswhile operatingthe pressurewasher.

Never operatethe pressurewasherwhile standing in water.

Never touch the electrical plug with wet hands.

Never let electrical connectionsrest in water.

Never operatepressurewasherwithout the water turnedon.

Never

use hotwater with this pressurewasher.

1800 PSI Pressure Washer

IMPORTANTSAFETYPRECAUTIONS

WARNING: When using this product, basic precautions should always be followed, including the following:

1.

Readall instructionsbefore usingthe product. Save all safety instructions.

2.

Donot operatethe pressure washer when fatigued or under the influence of alcohol or drugs.

3.

Riskof injection or injury- do not direct the high pressure water stream at any people or animals.

4.

Donot allow children to operate the pressure washer at any time.

5.

To reduce the risk of injury, close supervisionis necessary when the pressure washer is used near children.

6.

Know how to stop the unit and reduce pressure immediately.

Be completely familiar with the controls.

7.

Stayalert- always be aware of where you are directing the high pressure spray

8.

Keep cleaning area clear of all people.

9.

Keep goodfooting and balance at all times- do not overreach or stand on an unstablesupport.

10.

The work area should have adequate drainage to reduce the possibilityof a fall due to slippery surfaces.

1 1.

Followthe maintenance instructionsspecified in the manual.

1 2.

To reduce the risk of electrocution, keep all connections dry and offthe ground. Do not touch plug with wet hands.

GENERALSAFETYPRECAUTIONS

1.

Intended for outdoor householduse only.

2.

High-pressure hose can developleaks from wear, abuse, kinking etc. Do not use a damaged hose.

3.

Do not usethe pressure washer in areas near combustible materials, combustiblefumes, or dust.

4.

Somechemicals or detergents may be harmful if inhaled or ingested causing severe injury. Use a respirator or mask whenever there is a chance that vapors may be inhaled.

3

1800 PSI Pressure Washer

Readall instructions included with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.

5.

Before starting the pressure washer in cold weather, check all of the parts of the equipment and be sure that ice has not formed. Do not store the unit anywhere that the temperature will fall below O°C (32°F).

6.

DONOTMAKEANYMODIFICATIONS

COMPONENTS!Units with broken or missing parts, or without the protective housing or covers should NEVERbe operated

7.

Keep the high-pressure hose connected to the pressure washer and the spray gun while the system is pressurized.

Disconnecting the hose while the unit is pressurized is dangerous, and may cause injury.

8.

Do not leavethe pressure washer unattended while the power switch is ON.

9.

Keep water spray away from electrical wiring or fatal electric shock may result.

SERVICINGOF A DOUBLE-INSULATED

APPLIANCE

In a double-insulatedproduct, two systems of insulationare providedinstead of grounding. No means of grounding is providedon a double-insulatedproduct, nor should a means for grounding be added to the product. Servicing a double-insulated product requires extreme care and knowledge of the system, and should be done only by qualifiedservice personnel. Replacement parts for a double-insulatedproduct must be identical to the parts they replace. A double-insulatedproduct is marked with or "DOUBLEINSULATED".

may alsobe marked on the product.

USE OF EXTENSION

CORDS

extensioncord, use only extensioncords that are intendedfor outdoor use. These cords

1800 PSI Pressure Washer

electrical rating not less than the rating of the product. Examine extensioncord before use. Do not usedamaged extensioncords! Donot pull on cord to disconnect from receptacle, alwaysdisconnect by pulling on plug. Keep cord away from heat and sharp edges. Alwaysdisconnect the extensioncord from the receptacle before disconnecting the product from the extensioncord.

WARNING - To reduce the risk of electrocution, keep all connections dry and off

the ground. Do not touch the plug with wet hands.

PROPERUSEOF THE PRESSUREWASHER

THIS UNIT IS INTENDED FOR USE WITH COLD WATER ONLY!

DO NOT USE HOT WATER IN THIS PRESSURE WASHER.

5.

6.

.

.

.

.

Operatethe pressure washer at no more than the fluid pressure rated for the pressure washer. Never run the pressure washer without a water supply. Runningthe unit without a water supply will cause irreparable damage to the unit.

Make sure that the water supplyyou use for the pressure washer is not dirty, sandy, and does not hold any corrosive chemical products. Using a dirty water supply will compromise the long life of the pressure washer.

CAUTION- The pressure washer can be used for a variety of applicationsincluding washing cars, boats,patios, decks, garages etc. where high pressure is necessaryto remove dirt and debris.

High-pressurewater flow can damagethe work surface if not used properly! See the sectiontitled "Operating Instructions"for more details. Alwaystestthe spray in an open area first.

NEVERmove the unit bypulling on the high pressure hose. Use the handle providedon the top of the unit.

Always holdthe high pressure gun and wand with two hands.

Keep one hand on the gun/trigger, while supporting the wand with the other hand (see diagram).

Whendispensingdetergent, the pressure washer applies detergent to the cleaning area at low pressure only. Once the detergent has been applied,spray the detergent off ofthe work area by usingthe adjustablenozzle.

5

1800 PSI Pressure Washer

ASSEMBLYINSTRUCTIONS

UnpackingThe Carton

After openingthe carton, please remove all parts and checkthem against the following list of componentsthat are included:

A. High PressureWasher

B. Gun

C. High Pressure Hose

D. Adjustable Nozzle

E.Brass Connector

F. Water Intake Filter (Pre-lnstalled)

A

To assemblethe enclosed parts, please refer to the stepsthat follow:

1800 PSI Pressure Washer

Step 1

Attach the high pressure hose to the gun. Use a wrenchto tighten the fitting.

2

Step 2

Insertthe adjustablespray nozzle into the gun. Push and turn the adjustable nozzle clockwise ontothe gun until hand tight to lock it in place. Whenthe pieces are joined properly, you cannot separate the two components by pulling straight out on the adjustablenozzle.All attachments must be inserted into the gun for proper use.

1800 PSI Pressure Washer

Step 3

Attach the high-pressure hose to the male fitting on the front of the pressure washer.

Before attaching the high-pressure hose to the male fitting, remove the plastic cap, which is inserted onto the fitting before shipping. This plastic cap can be discarded once removed. Twist on tight to avoid leakage.

Step 4

Attachthe brassconnectorto pressurewasher.Beforeattachingthe connectorto the male fitting, removethe plasticcap,which is insertedontothe malefitting on the pressurewasher beforeshipping.This plasticcapcan be discardedonceremoved.After bothcomponentshave beeninstalled,attachthe gardenhosewith connectorscrew onthe pressurewasher.Connect

the gardenhoseto the waterspout.

1800 PSI Pressure Washer

OPERATINGINSTRUCTIONS

THIS UNIT IS INTENDED TO BE USED WITH COLD WATER ONLY!

DO NOT USE HOT WATER IN THIS PRESSURE WASHER!

StartingUp

After connectingthe pressure washer to your cold water supply, proceedas follows:

Make sure that the on/off switch is in the off position.

Connectthe garden hose with quick connect to the inlet fitting.

Attach the hoseto the gun as per assembly instruction step #1.

Insert the adjustable spray nozzle into the gun as per assembly step

#2.

Connectthe high pressure hoseto the high pressure outlet fitting as per assemblystep #3.

Openthe water supplyvalve completely.

Beforeturning the unit on, press the gun trigger to bleed all the remaining air out of the pump and hose.

Startthe pressure washer byturning the on/off switch to the on positionand squeeze the trigger.

WARNING - RISK OF INJECTION!

Unit will start spraying when trigger is squeezed.

When turning the unit off after

use, high pressure

still exists inside the hose and unit.

Point the gun in a safe direction and discharge the excess

pressure.

NEVER direct the high pressure

water stream at

people

or animals.

1800 PSI Pressure Washer

AutomaticOn / Off

The pressure washer is equipped with an automatic on/off switch.The pressure washer will only run when the power switch is in the ONposition and the trigger on the gun is squeezed. Whenyou release the trigger to stop spraying water through the gun, the motor on the pressure washer will automatically shut off. Simply squeezethe trigger again to resume using the washer. To stop using the pressure washer, releasethe trigger and switch the unit to the OFF position. The unit should be turned completely

OFFwhile not in use or while unattended.

BleedingThe Gun

It is very importantto bleedall the air out of the pressurewasher beforeusingit.Todo this

1. Releasetrigger lock.

2. Squeezethe trigger beforeturning the electricalsupply on.Thisremovesanyair trapped insidethe pressurewasher and lancebeforeusingthe units.

3. Continueholdingtrigger for approximatelyone minute to allowany excessair out of the unit.Waterwill flow throughthe gun at low pressureduring this procedure.

4. Lock the trigger.

5. Plugthe mains powercableinto the electricitysupply.

6. Releasethe trigger lock.

7. Trunthe ON/OFFswitch clockwiseto the I/ONposition.

The pressurewasher is readyto usingnow.

Gun SafetyLock

This pressure washer is equipped with a gun trigger safety lock. When not using the pressure washer, usethe safety lock to keep from accidentally engaging the high pressure spray.

AdjustableSpray Nozzle

The adjustable nozzlewill allow youto use anyvariety of spray patternsfrom a full fan spray (Diagram1) to a direct stream spray (Diagram2). When usingthe pressurewasher to cleanwood decks, siding, vehiclesetc., always start usingthe fan spray and begin spraying from a minimum 36" away to avoid damagingthe surface of the materialyou are cleaning. Always begin by spraying in a testing area free and clear of peopleand objects.

]0

1800 PSI Pressure Washer

DispensingDetergent

The built-in detergent dispenser will allow you to apply many forms of liquid detergent onto the work surface. Detergent application happens at low-pressure only. Insert the adjustable nozzle onto the gun, and turn it to end of ....

so that the pressure washer is in low-pressure mode (see FigureA below). Removethe cap on the detergent reservoir and fill with liquid detergent only (see Figure B below). Do not put any water into the reservoir. The pressure washer will mix water and detergent automatically.

When finished applying the detergent to the work surface, turn it to end of" + " of the adjustable nozzle and spray off the detergent by using the high-pressure spray

(see Figure A below). In high-pressure mode, the pressure washer will not dispense detergent.

FIGURE B

FIGURE A

Low Pressure Setting

High Pressure Setting

]!

1800 PSI Pressure Washer

ADJUSTINGTHE PRESSURE

To adjust the pressure,proceed as follows:

1. Hold the shaft of the lance in one hand.

2. Turn the grey part of the nozzle clockwise

(to "+" end) to obtain the high pressure.

3. Turn the grey part of the nozzle anticlockwise

(to "-" end) to obtain the low pressure.

Low Pressure Setting

High Pressure Setting

TOTAL STOPSYSTEM

The pressure washer is fitted with a total stop system to protect the motor when in use.

When the trigger is released the motor will stop.

When the trigger is squeezed the motor will start up again.

USINGDETERGENTS

The pressure washer will dispense detergent only at low pressure.

Usethe adjustable spray nozzle to apply detergents and to rinse clean.

Biodegradable detergents are specifically formulated to protect the environment and your pressure washer. These Detergents will not clog the filter and will protect the internal parts of the pressure washer for a longer life.

Step 1

Open the cover of the detergent reservoir by twisting it off.

Step 2

Fillthe detergent reservoir with any approvedliquid detergent.

Closethe cover.

]2

1800 PSI Pressure Washer

Step 3

Turn the adjustablenozzleto end of" - ", put the pressure washer into low-pressure mode.

Low Pressure Setting

Step 4

To apply the detergent cleanser to your working area, turn the pressure washer switch to the ONposition. Pull the trigger to operate the unit. The pressure washer will mix the detergent with water. Do not allow the detergent to dry on the object that you are cleaning.

WARNING: NEVER USE PRODUCTS WITH BLEACH OR CHLORINE

OR ANY OTHER

CORROSIVE

MATERIALS,

CONTAINING

SOLVENTS (I.E.

GAS,

INCLUDING

OILS ETC),

LIQUIDS

TRI-SODIUM

PHOSPHATE PRODUCTS, AMMONIA,

THESE

CHEMICALS

WILL HARM

OR ACID-BASED

THE UNIT AND

CAUSE

CLEANERS.

DAMAGE

TO THE SURFACE BEING

CLEANED.

ALWAYS READ THE LABEL.

Step 5

To clean the working area, turn the adjustablenozzleto end of " + ", return itto high-pressure mode. Spray high-pressure water onto the work area to rinse off the work area and any remaining detergent.

High Pressure Setting

]3

1800 PSI Pressure Washer

CLEAN-UPAND STORAGE

ShuttingDownthe PressureWasher

WHEN FINISHED USING THE PRESSURE WASHER, FOLLOW THESE

STEPS TO SHUT DOWN THE UNIT:

•

Turn the pressure washer to the OFFposition.

•

Turn off the water supply.

• Before disconnecting high-pressure hose connection, pointthe gun in a safe direction and discharge the high-pressure water.

• Disconnecthigh-pressure hose from the pressure washer and gun.

• Disconnectgarden hose from the pressure washer.

• Removeexcess water from the pump bytippingthe unit on both sidesto drain any remaining water from inlet and outlet fittings.

• RemoveWater Intake Filter and flush with water to remove dirt or debris.

Return filter once cleaned.

• Drain detergent reservoir and flush with running water.

• Wipe away any remaining water on all parts and fittings.

• Engagethe gun safety lock.

• Storethe pressure washer, parts, and accessories in an area with a temperature above 0% (32°F).

]4

1800 PSI Pressure Washer

Winterizingand Long-TermStorage

FOLLOW ALL OF THE ABOVE SHUT-DOWN PROCEDURES,ADDING

THE FOLLOWING

STEPS ....

•

After disconnectingthe water supply,and before disconnectingthe high-pressure hose, turn the pressure washer on for 2-3 seconds,until any remaining water in the pump exits. Turn unit off immediately.

CONTINUED

WATER

USE OF THE PRESSURE

SUPPLY

THE UNIT!

ATTACHED

WASHER WITHOUT

WILL CAUSE SEVERE DAMAGE TO

• Always store the pressure washer, parts, and accessories in an area with a temperature above 0° C (32° F).

WARNING: FAILURE TO COMPLY WITH THESE STORAGE

INSTRUCTIONS WILL RESULT IN DAMAGE TO THE PUMP

ASSEMBLY.

Maintenance

• This pressure washer is suppliedwith a closed lubrication system, so no additionof oil is needed.

• Checkall hoses and accessoriesfor damage prior to use.

• Checkthe water intake filter periodicallyfor deposits. Cleanthis filter regularlyfor maximum performance.

]5

1800 PSI Pressure Washer

CLEANINGTIPS

WARNING: ALWAYS TEST THE SPRAY IN AN AREA FREE AND

CLEAR OF PEOPLE AND OBJECTS BEFORE YOU SPRAYAT THE

INTENDED CLEANING SURFACE.

Wood andVinyl Decks

Rinse deck and surrounding area with fresh water. If using detergent, fill the detergent reservoir and apply to the area being cleaned at low pressure. For optimal results, reduce your work area to smaller sections and clean each section one at a time. Allow the detergent to rest on the surface for a few minutes and thenrinse at high pressure.

Do not let the cleanser dry. Always clean from left to right and top to bottom for best results. Rinse at high pressure using the fan spray keeping the tip of the spray nozzle at least 6-9 inches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray.

Caution: For softer woods,increase the distance from the cleaning area.

CementPatios,Stone,and Brick

Rinsecleaning and surrounding area with fresh water. If usingdetergent, fill the detergent reservoir and applyto the area being cleaned at low pressure. Rinseat high pressure usingthe fan spray in a sweeping motion keepingthe tip of the spray nozzle at least 3-6 inches from the cleaning surface. Maintain a further distancefrom the cleaning area when using a direct spray.

Cars,Boats,and Motorcycles

Rinse cleaning and surrounding area with fresh water. If using detergent, fill the detergent reservoir and apply to the area being cleaned at low pressure. To achieve the best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes, but do not let the detergent dry. Rinse at high pressure using the fan spray in a sweeping motion keeping the tip of the spray nozzle at least 8 inches from the cleaning surface.

]6

1800 PSI Pressure Washer

Maintain a further distancefrom the cleaning area when using a direct spray. Wipe surface dry for a polishedfinish.

BarbecueGrills, PowerEquipment,and GardenTools

Rinsecleaning and surrounding area with fresh water. If usingdetergent, fill the detergent reservoir and applyto the area being cleaned at low pressure. Allow the detergent to rest on the surface for a few minutes, but do not let the detergent dry.

Rinseat high pressure usingthe fan spray keepingthe tip of the spray nozzle at least

1-3 inches from the cleaning surface. Maintain a further distancefrom the cleaning area when using a direct spray.

TECHNICALDATA

Mains voltage

Mains frequency

Max. operating pressure

Water consumption

Max. pressure water supply

Max. water temperature

Weight

120V

60 Hz

1800PSI

1.6 GPM

0.3 Mpa

5-60oc

9 Kg

GUARANTEE

Referto the enclosedguaranteeconditionsfor the terms and conditionsof guarantee.

ENVIRONMENT

Should your machine need replacement after extended use, do not put it in the domestic waste but dispose of it in an environmentally safe way.

]?

1800 PSI Pressure Washer

WHEN THE SWITCH IS IN THE "1" POSITION THE MACHINE WILL NOT START

PROBABLE CAUSE

Electricalsocket isfaulty

Voltageis inadequate

GFCItrips

Power cord is not plugged in

SOLUTION

Checkplug, socket, and fuses

Checkthat the voltage is adequate

Reset/ Try another outlet

Plug in power cord

THE PUMP DOESNOT REACHADEQUATEPRESSUREOR FLUCTUATES

PROBABLE CAUSE

Water Intake Filter is clogged

Pump is drawing air

Suction valves are clogged/worn

Diameter of garden hose too small

Water supply is restricted

Insufficient water supply

SOLUTION

Removeand clean filter

Tighten connections/bleed system

Cleanor replace valves

Replacewith 3Ainch garden hose

Check hosefor kinks or leaks

Fully open water source

THE PRESSUREWASHER HAS OR WILL NOT MAINTAIN PRESSURE

PROBABLE CAUSE

Excessiveair in waterline and pump

SOLUTION

Turn unit and water supply off /

Bleedsystem / Holdtrigger down

THE PRESSUREWASHER MAKES EXCESSIVENOISE

PROBABLE CAUSE

Intake is blocked

Valves are worn, dirty, or clogged

Water Intake Filter is dirty

THE MOTORSTOPS RUNNINGWHILE IN USE

SOLUTION

Checkthe intake valves

Check, clean or replace valves

Check, clean, or replace filter

PROBABLE CAUSE

Net voltage lower than suggested

SOLUTION

Checkthat the voltage is adequate

18

LimitedWarranty

final

Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveotherrightswhichvaryfrom stateto state.

Manual(s).

be paidbythepurchaser.

!9

LimitedWarranty

costs.

any,willapply.

applytoyou.

abovelimitationsmaynotapplytoyou.

2O