Emerson LC320EM8A Owner`s manual

EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
Owner’s Manual
LC320EM8A
CONNECTION
32” Digital / Analog
LCD TV
INTRODUCTION
TM
INITIAL SETTING
WATCHING TV
OPTIONAL SETTING
TROUBLESHOOTING
TO RECEIVE DIGITAL/ANALOG SIGNAL,
YOU MUST CONNECT ANTENNA.
IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-256-2487, OR
VISIT OUR WEB SITE AT http://www.EmersonAudioVideo.com
INFORMATION
HIGH-DEFINITION TELEVISION
INTRODUCTION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THE APPLIANCE.
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The important note is located on the rear of the cabinet.
Important Safeguards
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the
operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions
should be followed.
5. CLEANING - Unplug TV from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
EXCEPTION: A product that is meant for uninterrupted service and,
that for some specific reason, such as the possibility of the loss
of an authorization code for a CATV converter, is not intended to
be unplugged by the user for cleaning or any other purpose, may
exclude the reference to unplugging the appliance in the cleaning
description otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by
the TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this TV near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on
an unstable cart, stand, tripod, bracket,
or table. The TV may fall, causing serious
injury to someone, and serious damage to
the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the TV.
Any mounting of the appliance should follow
the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
AMEUBLES - Cet appareil ne doit être placé
que sur un meuble (avec ou sans roulettes)
recommandé par le fabricant. Si vous l’
installez sur un meuble à roulettes, déplacez
les deux ensembles avec précaution. Un arrêt
brusque, l’utilisation d’une force excessive
et des surfaces irrégulières risquent de
déstabiliser l’ensemble et de le renverser.
9. VENTILATION - Slots and openings in the
cabinet and the back or bottom are provided for ventilation
and to ensure reliable operation of the TV and to protect it from
overheating, these openings must not be blocked or covered. The
openings should never be blocked by placing the TV on a bed,
sofa, rug, or other similar surface. This TV should never be placed
near or over a radiator or heat register. This TV should not be
placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s instructions
have been adhered to.
10. POWER SOURCES - This TV should be operated only from the type
of power source indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your appliance
dealer or local power company. For TVs intended to operate from
2
EN
battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION - This TV is equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they
exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or
cable system is connected to the TV, be sure the antenna or cable
system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides information
with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SEC TION 810-20)
ELEC TRIC
SERVICE
EQUIPMENT
GROUNDING CONDUC TORS
(NEC SEC TION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELEC TRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELEC TRODE SYSTEM
(NEC ART 250, PART H)
14. LIGHTNING - For added protection for this TV receiver during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the TV due
to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light of
power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
CONNECTION
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts specified by
the manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
TV, ask the service technician to perform routine safety checks to
determine that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
INTRODUCTION
INITIAL SETTING
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this TV through openings as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the TV.
c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance, this
indicates a need for service.
5 Precautions
WATCHING TV
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment
may cause harmful interference unless the modifications are expressly approved in the manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the
building as close to the point of cable entry as practical.
INFORMATION
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
TROUBLESHOOTING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
OPTIONAL SETTING
CAUTION:
ATTENTION:
“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.”
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
3
EN
INTRODUCTION
LOCATION
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the
unit. Do not place the unit on a carpet because this will block the ventilation holes.
• Install the unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving the unit to locations where temperature differences are extreme.
• Be sure to unplug the AC power cord from the outlet before carrying the unit.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug the power cord immediately and take the unit to our authorized service center for
servicing.
• Do not place anything directly on top of the unit.
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours.
You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
date of purchase
dealer phone No.
serial No
dealer purchase from
model No.
dealer address
Note about recycling:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with
your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
5 Supplied Accessories
owner’s manual
(1EMN22139)
remote control
(NF015UD)
batteries
(AA x 2)
• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free
customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
Contact your local electronics store for these items.
5 Symbols Used in this Manual
The following is the description for the symbols used in this manual.
Description refers to:
DTV
: Digital TV operation
TV
: Analog TV operation
• If neither symbol appears under the function heading, operation is applicable to both.
4
EN
5 Contents
INTRODUCTION
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Basic Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INITIAL SETTING
Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
OPTIONAL SETTING
TROUBLESHOOTING
Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Manual Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Antenna Confirmation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DTV Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
CC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
HDMI Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
OPTIONAL SETTING
Channel Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Volume Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Still Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Switching Each Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TV Screen Display Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
WATCHING TV
WATCHING TV
INITIAL SETTING
CONNECTION
CONNECTION
TROUBLESHOOTING
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
INFORMATION
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrical Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back cover
INFORMATION
• DTV/TV/CATV
- You can use your remote control to select channels
which are broadcast in digital, conventional analog,
standard definition, and high definition formats.
Also, cable subscribers can access their cable TV
channels.
• Program Information Display (DTV only)
- You can display the title, contents and other
information of the current DTV program on the TV
screen.
• Auto Channel Scan
- This unit automatically scans and memorizes
channels available in your area, eliminating difficult
setup procedures.
• V-chip
- This feature allows you to block children’s access to
inappropriate programs.
• Closed Caption Decoder
- Built-in closed caption decoder displays text for
closed caption supported programming.
• MTS/SAP Tuner
- Audio language can be selected from the remote
control.
• Auto Shut Off Function
- If there is no signal input from the antenna terminal
and no operation for 15 minutes, the unit will turn
off automatically.
• Sleep Timer
- This feature will automatically turned off the power
of the unit at a specific time.
• Choices for On-screen Language
- Select your on-screen language:
English, Spanish or French.
• Stereo Sound Function
• PLL Frequency Synthesized Tuning
- Provides free and easy channel selection and lets
you tune directly to any channel using the channel
number buttons on the remote control.
• Resume
- This unit automatically memorizes settings if a
power failure occurs.
• HDMI Input
• Component Video Input
• S-video Input
• AV Input
• Digital Audio Coaxial Output
INTRODUCTION
5 Features
© 2007 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in
any storage medium, in any form or for any purpose without the express prior written consent of Funai.
Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the
obligation to notify any person or organization of such changes.
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written
consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this
manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein.
Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property
rights to the fullest extent of the law.
5
EN
INTRODUCTION
5 Remote Control Function
1. POWER button (p12)
Press to turn the unit on and off.
2. Number buttons (p15)
• Press to select channels.
- button
• Press to shift the minor channel
from the major channel.
3. SETUP button (p13)
Press to display the main menu.
4. s / B / K / L buttons (p12)
Press to move left/ right/ up/
down through the items.
5. ENTER button (p12)
Press to decide the command of
setting when the main menu is
displayed.
6. BACK button (p18)
Press to return to previous menu
operation.
7. CH RETURN button (p15)
Press to return to previous
channel.
8. VOL. X / Y buttons (p15)
Press to adjust the volume.
9. MUTE button (p15)
Press to turn the sound on and off.
10. INPUT SELECT button (p16)
Press to access connected
external device like a DVD player
or VCR.
11. SLEEP button (p20)
Press to activate the sleep timer.
12. AUDIO button (p17)
Digital Mode (DTV)
Press to select the audio language.
Analog Mode (TV)
Press to select the audio mode.
13. STILL button (p16)
Press to pause screen image.
14. SCREEN MODE button (p19)
Press to select aspect ratio
available for the TV screen.
15. INFO button (p18)
Digital Mode (DTV)
• Press to display the channel
information, signal type and TV
setting.
Analog Mode (TV)
• Press to display the channel
number, signal type and TV
setting.
External Input Mode
• Press to display the external
input mode, signal type and TV
setting.
16. CH K / L buttons (p15)
Press to select channels and the
external input mode.
5 Installing the Batteries
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
Battery Precautions:
•
•
•
•
6
EN
Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
Do not try to recharge batteries; they can overheat and rupture.
INTRODUCTION
5 Control Panel
SETUP
VOLUME
CHANNEL
INPUT
SELECT
POWER
top of this unit
rear of this unit
Y
R
R
AUDIO AUDIO
L
L
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 2
7
COMPONENT 1
Y
R
R
AUDIO AUDIO
Pb
1
2
3
4
5
L
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
Pb
L
9
10
8
L
S VIDEO VIDEO
Pr
VIDEO 2
rear of this unit
8
L
S VIDEO VIDEO
rear of this unit
9
10
INFORMATION
6
TROUBLESHOOTING
COMPONENT 1
Pb
1. HDMI - IN jack (p9)
HDMI connection for an HDMI device.
2. AUDIO IN jacks (p9)
RCA audio cable connection for a DVI device.
3. AUDIO OUT jacks (p11)
RCA audio cable connection for an external device.
Use analog audio input jacks of an external device.
4. DIGITAL AUDIO OUT (COAXIAL) jack (p11)
Digital audio coaxial cable connection for a decoder or
an audio receiver.
Use digital audio input jack of an external device.
5. ANT. IN jack (p8)
RF coaxial cable connection for your antenna or cable
box.
6. AC power cord
Connect to a standard AC outlet to supply power to
this unit.
7. COMPONENT and AUDIO input jacks (p10)
Component video cable and RCA audio cable
connection for an external device.
Use component video and audio output jacks of an
external device.
8. AUDIO input jacks (p10)
RCA audio cable connection for an external device.
9. VIDEO input jack (p11)
RCA video cable connection for an external device.
10. S-VIDEO input jack (p10)
S-video cable connection for an external device.
OPTIONAL SETTING
5 Rear Panel
WATCHING TV
6
INITIAL SETTING
1. SETUP button (p13)
Press to display the main menu.
2. VOLUME X / Y buttons (p15)
Press to adjust the volume or move right (X) / left (Y)
through the main menu items.
3. CHANNEL K / L buttons (p15)
Press to select channels or move up/down through the
main menu items.
4. INPUT SELECT button (p16)
• Press to access connected an external device like a
DVD player or VCR.
• Press to decide the command of setting when the
menu is displayed.
5. POWER button (p12)
Press to turn the unit on and off.
6. Infrared Sensor Window
Receives infrared rays transmitted from the remote
control.
CONNECTION
1
2
3
4
5
7
EN
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
5 Basic Connection
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
[Antenna Cable Connection]
When connecting the unit to an antenna or cable TV company (without cable/satellite box)
Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
e.g.)
VHF / UHF
antenna
rear of this unit
RF coaxial cable
or
COMPONENT 1
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 2
cable TV
company
* Once connections are completed, turn on the unit and begin initial setup.
Channel scanning is necessary for the unit to memorize all available channels in your area.
(Refer to “Initial Setup” on page 12.)
Note:
• For your safety and to avoid damage to device, please unplug the RF coaxial cable from the antenna input jack before moving the unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than
settop versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CATV installer.
[Connection to Cable Box or Satellite Box]
Connect the RF coaxial cable on your home outlet to the input jack of the cable/satellite box.
Use another RF coaxial cable to connect the antenna input jack of the unit to the output jack of the cable/satellite box.
e.g.)
rear of this unit
satellite
dish
cable/satellite box
or
ANT. IN RF OUT
COMPONENT 1
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 2
cable TV
company
RF coaxial cable
RF coaxial cable
* Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
8
EN
INTRODUCTION
Cables not included.
Please purchase the necessary cables at your local store.
5 External Device Connection
CONNECTION
[HDMI Connection]
HDMI (High Definition Multimedia Interface) transports high definition video and multi-channel digital audio through a
single cable. It ensures that the content sent from the source to TV is of the highest possible resolution.
rear of this unit
INITIAL SETTING
e.g.)
To HDMI - IN jack
HDMI cable
HDMI OUT
COMPONENT 1
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 2
DVD player with the HDMI output jack
• This unit accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.
• This unit accepts only 2 channel audio signal (LPCM).
• You need to select “PCM” for the digital audio output of the device connected or the HDMI audio setting. There may be no audio output if
you select “Bitstream”, etc.
• This TV only accepts signals compliant with EIA861.
OPTIONAL SETTING
[HDMI-DVI Connection]
If your video device has a DVI output jack, connect using a HDMI-DVI conversion cable.
rear of this unit
To HDMI - IN jack
HDMI-DVI
conversion cable
TROUBLESHOOTING
e.g.)
DVI OUT
COMPONENT 1
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 2
Cable box or satellite box
with the DVI output jack
WATCHING TV
Note:
AUDIO OUT
L
R
INFORMATION
To AUDIO IN jacks
RCA audio cable
Note:
•
•
•
•
This unit accepts 480i / 480p / 720p / 1080i video signals.
An HDMI-DVI conversion cable requires a separate audio cable connection as well.
Audio signals are converted from digital to analog for this connection.
DVI does not display 480i image that is not compliant with EIA/CEA-861/861B.
9
EN
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
[Component Video Cable Connection]
Component video connection offers better picture quality for video devices connected to the unit.
Use a component video cable to connect the unit to external video devices equipped with component video output
jacks.
If you connect to the unit’s COMPONENT 1 video input jack, connect RCA audio cables to the audio L/R jacks of
COMPONENT 1.
If you connect to the unit’s COMPONENT 2 video input jack, connect RCA audio cables to the audio L/R jacks of
COMPONENT 2.
component video cable
(green)
(blue)
(red)
e.g.)
rear of this unit
Y
Pb
Pr
COMPONENT VIDEO OUT
DVD player with the component
video output jacks
AUDIO OUT
L
R
(green)
COMPONENT 1
Y
R
R
AUDIO AUDIO
(blue)
Pb
L
L
S VIDEO VIDEO
(red)
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
RCA audio cable
Note:
• This unit accepts 480i / 480p / 720p / 1080i video signals.
[S-video Cable Connection]
S-video connection offers good picture quality for video devices connected to the unit.
Use an S-video cable to connect the unit to external video devices equipped with S-video output jack.
If you connect to the unit’s VIDEO 1 S-video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 1.
If you connect to the unit’s VIDEO 2 S-video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 2.
e.g.)
AUDIO OUT
L
R
S-VIDEO
OUT
rear of this unit
DVD player with the S-video output
jack
COMPONENT 1
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
Y
R
R
AUDIO AUDIO
Pb
L
L
S-video cable
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
10
EN
INTRODUCTION
Cables not included.
Please purchase the necessary cables at your local store.
CONNECTION
[Video Connection]
Video connection offers standard picture quality for video devices connected to the unit.
If you connect to the unit’s VIDEO 1 video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 1.
If you connect to the unit’s VIDEO 2 video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 2.
When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack.
rear of this unit
INITIAL SETTING
e.g.)
COMPONENT 1
Y
AUDIO OUT
L
R
VIDEO
OUT
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
camcorder
video game
VIDEO 1
COMPONENT 2
Y
R
R
WATCHING TV
RCA video cable
RCA audio cable
VCR
Note:
OPTIONAL SETTING
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
TROUBLESHOOTING
[Audio Output Connection]
[Digital]
If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound.
[Analog]
If you connect this unit to an external analog audio device, you can enjoy stereo (2 channel) audio.
AUDIO IN
L
R
e.g.)
INFORMATION
Stereo system
RCA audio cable
e.g.)
rear of this unit
DIGITAL AUDIO
COAXIAL IN
To AUDIO OUT
jack
COMPONENT 1
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
digital audio
coaxial cable
Y
R
R
AUDIO AUDIO
Pb
L
L
S VIDEO VIDEO
Pr
VIDEO 2
Dolby Digital decoder
To DIGITAL AUDIO
OUT jack
11
EN
INITIAL SETTING
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
5 Initial Setup
Note:
This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and auto channel scan,
which automatically scans and memorizes viewable channels.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1 After making all the necessary connections, press
[POWER] to turn on the unit.
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel
scan, this setting will be canceled.
• The initial auto channel scan function can be executed
for either “Air” or “Cable” only once. When you change the
connection (Air/Cable), set auto channel scan again. (Refer
to page 13.)
• You can cancel or exit the initial auto channel scan menu
by pressing [SETUP].
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
“Helpful Hints” appears. Follow the instructions listed on
the TV screen.
• This operation may take a few moments.
2-2
2 Use [Cursor K/L] to select the on-screen language
from the choices on the right side of the TV screen.
(English / Español / Français)
Initial Setup
Select the language for setup display.
English
Elija el idioma de ajuste.
Español
Sélectionner langue écran config.
Français
Select
ENTER
SETUP
Enter
Exit
• “Initial Setup” menu on step 3 will be displayed in the
selected language after you press [ENTER].
3 Use [Cursor K/L] to select “Air” for TV channels or
“Cable” for CATV channels, then press [ENTER].
Initial Setup
Air
Make sure the antenna is connected to "ANT.IN" jack.
Select the destination of "ANT.IN" jack.
Cable
Air
Or
Cable
Select
ANT.IN
ENTER
Enter
BACK
SETUP
Back
Exit
• Scanning and memorizing of channels start
automatically.
Initial Setup
Now the system is scanning for channels,please wait.
5%
Analog channels
1ch
Digital channels
0ch
SETUP
Exit
• When the scanning and memorizing are completed,
the lowest memorized channel in the broadcasting
will be displayed.
12
EN
No channel is registered.
Press and hold "ENTER" key on the remote control for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Pulse durante 3 segundos la tecla "ENTER" en el control remoto.
Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign.
Enfoncez "ENTER" 3 secondes sur la télécommande.
Contacter numero d'urgence dans manuel ou arrière appareil.
5 Auto Channel Scan
This section describes the overview of the main menu displayed when you
press [SETUP]. For more details, see the reference page for each item.
The main menu consists of the function setting items below.
If you switch wires (e.g., between antenna and CATV) or if you move the TV
to a different area after the initial setting, or if you restore the DTV channel
you deleted, you will need to perform auto channel scan.
CONNECTION
Before you begin:
Make sure if the unit is connected to antenna or cable.
Press [SETUP].
1 Press [SETUP] to display the main menu.
INITIAL SETTING
2 Use [Cursor K/L] to select “CHANNEL” , then press
[ENTER].
3
WATCHING TV
Use [Cursor K / L] to select “Autoscan”, then press
[ENTER].
OPTIONAL SETTING
Channel
Autoscan
Channel List
Manual Register
Antenna
Use [Cursor K / L] to select an appropriate option, then
press [ENTER].
Autoscan
Autoscan will rescan all channels.
This may take a while to complete.
Select the destination of "ANT.IN" jack.
Back
TROUBLESHOOTING
• EXIT
To exit settings.
• PICTURE
You can adjust the picture quality.
(Refer to “Picture Adjustment” on page 23.)
• CHANNEL
You can automatically scan the viewable channels
and remove those that are undesired.
(Refer to “Auto Channel Scan” on page 13.)
• DETAIL
You can change the display format for closed
caption, which displays the dialogue of a TV program
or other information across the TV screen.
(Refer to “Closed Caption” on page 24.)
Set the viewing limitations.
(Refer to “V-chip” on page 28.)
And select the sound input for the HDMI jack if your
TV is connected to a HDMI device.
(Refer to “HDMI Audio” on page 31.)
• LANGUAGE
You can change the language (English, Spanish,
French) displayed on the main menu.
(Refer to “Language Selection” on page 14.)
INTRODUCTION
5 Main Menu
Air
Cable
Cable
1hour
Air
INFORMATION
Cable
Or
ANT.IN
• When aerial antenna is connected, select “Air”.
• When connected to CATV, select “Cable”.
• Scanning and memorizing of channels start
automatically.
Now the system is scanning for channels, please wait.
72%
Analog channels
10ch
Digital channels
SETUP
6ch
Exit
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
13
EN
INITIAL SETTING
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel
scan, the setting will be canceled.
• Channel settings will be saved even if the power fails.
• If you need the English menus instead of the Spanish
or French menus you are having, press [SETUP]. Use
[Cursor K / L] to select “IDIOMA” or “LANGAGE”, then press
[ENTER]. Use [Cursor K / L] to select “English”, then press
[ENTER]. Press [SETUP] to exit the main menu.
• With regard only to the digital channel, even after the
scanning is complete if you unplug the AC power cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.
5 Language Selection
You can choose English, Spanish, or French as your on-screen language.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K/L] to select “LANGUAGE”, then press
[ENTER].
3 Use [Cursor K/L] to select “English”, “Español” or
“Français”, then press [ENTER].
Language
4 Press [SETUP] to exit.
14
EN
Select the language for setup display.
English
Elija el idioma de ajuste.
Español
Sélectionner langue écran config.
Français
5 Channel Selection
5 Volume Adjustment
Select channels by pressing [CH K / L] or [the Number buttons].
This section describes how to adjust the volume. The mute function, which
turns the sound off and on, is also described.
Use [VOL. X / Y] to adjust the audio volume.
To Use [the Number buttons]
• The volume bar will be displayed at the bottom of
the TV screen when adjusting the volume.
• The volume bar display will automatically disappear
in a few seconds.
- When selecting analog channel 12
20
INITIAL SETTING
TV
Volume
CONNECTION
• To select the memorized channels, use [CH K / L] or
[the Number buttons].
• To select the non-memorized channels use
[the Number buttons].
Press [MUTE] to turn off and on the sound.
DTV
INTRODUCTION
WATCHING TV
Mute
WATCHING TV
- When selecting digital channel 12-1
Be sure to press [–] before entering the minor
channel number.
• “Mute” is displayed on the TV screen for a few
seconds.
Press [MUTE] again or [VOL. X / Y] to recover the
original volume.
OPTIONAL SETTING
• Press [CH RETURN] to return to the previously
viewed channel.
ATSC (digital mode)
CH4
INFORMATION
NTSC (analog mode) [Air Time]
18:00
TROUBLESHOOTING
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting
far surpasses analog broadcasting in both its picture
and sound quality.
What is the minor channel?
By using high compression technology, digital
broadcasting offers a service that enables multiple
signals to send simultaneously.
Therefore, you can select more than one program per
major channel since digital broadcasting technology
distinguishes between multiple channels broadcast by
a single network.
No signal No signal
18:30
CH4
CH4
(high definition TV)
19:00
CH4
CH4-1
CH4
No signal CH4-2
No signal
19:30
20:00
CH4
CH4-1
CH4-2
20:30
major channel
minor channel
: change automatically
: change manually by using [CH K / L]
Note:
• “No Signal” will appear on the TV screen after the minor
channel broadcast is over.
15
EN
WATCHING TV
5 Still Mode
5 Switching Each Mode
You can freeze the image shown on the TV screen.
You can easily switch with the remote control to the DTV (ATSC) and TV
(NTSC) or to access an external device when they are connected to the unit.
Press [STILL] to pause the image shown on the screen.
Press [INPUT SELECT] or [CH K] repeatedly to cycle
through the input modes.
Still
TV/DTV channel
• The sound output will not be paused.
• If no signal is detected or protected signal is received
during still mode, the image remains paused and the
sound output will be muted.
• The still function will be released after 5 minutes.
Video1
or
Video2
Component1
Component2
To cancel still mode, press any button except [POWER].
HDMI
• Pressing [CH L] reverses the direction of the mode.
• To use the video or S-video input jack of VIDEO 1 on
the unit, select “Video1”.
• To use the video or S-video input jack of VIDEO 2 on
the unit, select “Video2”.
• To use the component video input jack of
COMPONENT 1 on the unit, select “Component1”.
• To use the component video input jack of
COMPONENT 2 on the unit, select “Component2”.
• To use the HDMI - IN jack on the unit, select “HDMI”.
16
EN
INTRODUCTION
5 Switching Audio Mode
This section describes how to switch the audio language.
TV
DTV
audio mode. While receiving an MTS broadcast,
press repeatedly to cycle through the available audio
channel.
1 Press [AUDIO] to display the currently selected
CONNECTION
1 Press [AUDIO] to display the currently selected
language and the number of available languages.
6-1
English 1/3
6
SAP / STEREO
INITIAL SETTING
2 Press [AUDIO] repeatedly to cycle through the
available audio languages.
When all audio are available
SAP / STEREO
SAP / MONO
SAP / STEREO
English 1/3
Spanish 2/3
When stereo and monaural audio are available
Other 3/3
MONO / STEREO
When SAP and monaural audio are available
SAP / MONO
SAP / MONO
When only monaural audio is available
• Available languages differ depending on the
broadcast. “Other” is displayed when the audio
language cannot be acquired, or the acquired
languages are other than English, Spanish or French.
• The current mode will automatically disappear in 4
seconds.
OPTIONAL SETTING
MONO
WATCHING TV
MONO / STEREO
(Cannot be switched)
Note:
STEREO
SAP
MONO
: Outputs stereo-audio
: Outputs second audio program
: Outputs mono-audio
• Pressing [AUDIO] does not control external audio device.
TROUBLESHOOTING
• The current mode will automatically disappear in 4
seconds.
INFORMATION
17
EN
WATCHING TV
5 Screen Information
You can display the currently selected channel or other information such as
the audio mode on the TV screen.
DTV
TV
In the analog mode, the current channel number and the audio mode are
displayed.
In the digital mode, the detailed broadcasting information for the current
channel such as program title, program guides are displayed.
Press [INFO] to display the details of the currently
selected program.
Press [INFO].
6
SAP / STEREO
480i
480i
SD
SD
4:3
TV-PG DLSV CC
CC
• The current channel number, audio mode, type of
resolutions for video signal, TV aspect ratio, CC and
TV rating are displayed at the top-right corner of the
TV screen.
To clear the display, press [INFO] again.
You can also press [BACK].
[Broadcasting Information]
• The following information is displayed.
1 program title
2 broadcast station
3 program guide
(The program guide added to broadcasting
information is displayed. Maximum display of 4
lines.)
4 channel number
5 audio language
(Refer to “Switching Audio Mode” on page 17.)
6 effective scanning lines and scan mode
7 program format
8 program aspect ratio
9 program rating
10 CC (not available if CC is set to “Off”)
1
2
A Day of Memories
4
KABC
A quarter-century ago,which may now qualify as the
good old days of newspapering,run-of-paper sales
accounted for 80 percent of the industry's advertising
revenues.Department stores and supermarket were
6-1
English 1/2
1080i
3
HD
HD
5
16:9
16:9
TV-PG DLSV CC
CC
6, 7, 8
9 10
Note:
• When the program guide consists of more than 4 lines, use
[Cursor K/ L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• While the program guide is displayed, the closed caption
function is interrupted.
• In external input mode, the following screen is displayed;
e.g.) When an external device is connected to VIDEO 1
input jack.
Video1
480i
480i
SD
SD
TV-PG DLSV CC
CC
• Available languages differ depending on the broadcast.
• The information display will automatically disappear in 4
seconds.
• Pressing [AUDIO] does not control external audio device.
18
EN
INTRODUCTION
5 TV Screen Display Mode
4 types of display modes can be selected when the broadcasting station is
sending 4:3 or 16:9 video signal.
For 16:9 video signal
CONNECTION
Press [SCREEN MODE] repeatedly to switch the TV
aspect ratio.
Full
(normal)
Zoom
Expand
Cinema
Sidebar
(normal)
Full
Cinema
OPTIONAL SETTING
Note:
• You may not switch the display mode depending on the
program.
TROUBLESHOOTING
[Sidebar]
Display a 4:3 picture at its original size. Sidebars appear
on both edges of the screen.
[Full]
Display a 4:3 picture at a 16:9 size; the picture is
stretched horizontally to fill the screen.
[Cinema]
Display a 4:3 picture at a 16:9 size; the picture is
stretched horizontally and vertically to fill the screen.
This crops out the top and bottom of the picture.
[Wide]
Display the picture with its center at the original size
and the edges stretched horizontally.
[Full]
Display a 16:9 picture at its original size.
[Zoom]
Display a 16:9 picture at its maximum size without
changing its horizontal and vertical ratio.
[Cinema]
Display a vertically stretched picture.
[Expand]
Display a horizontally stretched picture.
WATCHING TV
Wide
INITIAL SETTING
For 4:3 video signal
INFORMATION
19
EN
WATCHING TV
5 Sleep Timer
The sleep timer can be set to automatically turn off the unit after an
incremental period of time.
1 Press [SLEEP] to set the sleep timer.
Sleep
Off
• Sleep timer display appears on the TV screen.
2 Press [SLEEP] repeatedly to change the amount of time
until shut off.
Sleep
120min.
• You can set your unit to turn off after a set period of
time (from 30 to 120 minutes).
• Each press of [SLEEP] will increase the time by 30
minutes.
• After set up, the sleep timer display can be called up
for checking by pressing [SLEEP].
To Cancel the Sleep Timer
Press [SLEEP] repeatedly until “Sleep Off” is displayed
on the TV screen.
Note:
• The sleep timer setting display will automatically
disappear in 4 seconds.
• When you disconnect the unit from the AC outlet or when
a power failure occurs, the sleep timer setting will be
canceled.
20
EN
5 Manual Register
The channel list function lets you remove undesired channels from the
channel registration list.
The manual register function lets you add the channels that were not added
by the auto channel scan due to the reception condition at the initial setting.
1 Press [SETUP] to display the main menu.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K/L] to select “CHANNEL”, then press
2 Use [Cursor K/L] to select “CHANNEL”, then press
3
3 Use [Cursor K/L] to select “Manual Register”, then
[ENTER].
CONNECTION
5 Channel List
INTRODUCTION
OPTIONAL SETTING
[ENTER].
INITIAL SETTING
press [ENTER].
Channel
Autoscan
Autoscan
Channel List
Channel List
Manual Register
Manual Register
Antenna
Antenna
OPTIONAL SETTING
Channel
4 Use [Cursor K/L] to select the channel you want to
WATCHING TV
Use [Cursor K / L] to select “Channel List”, then press
[ENTER].
4 Use [the Number buttons] to enter the number of the
channel you want to add, then press [ENTER].
TROUBLESHOOTING
remove, then press [ENTER].
Channel List
Highlight channels for
Ch Up/Down key selection.
DTV
6
DTV
8
DTV
48
11
27
Manual Register
9
For analog channels,
select a channel to register using
number keys.
For digital channels,
you must perform Autoscan function.
58
DTV
Ch Select
ENTER
Watch/Skip
BACK
67
Back
• The channel with the “DTV” indicated on the display is
ATSC. Otherwise the channel is NTSC.
5 Press [SETUP] to exit.
BACK
Ch Change
INFORMATION
• The channel display for the removed channel
darkens. You will not be able to select the channel
again using [CH K / L].
• To reactivate a removed channel, highlight it using
[Cursor K / L] and press [ENTER]. The channel
display lightens.
• When you remove a major channel, its minor
channels are removed as well.
Note:
Register
Back
5 Press [SETUP] to exit.
Note:
• If set up completes successfully, “Registered to the Channel
List” is displayed.
• If external input is used, it is not possible to register the
channel and “Unavailable” will be displayed on the TV
screen.
21
EN
OPTIONAL SETTING
5 Antenna Confirmation
This function lets you check the signal strength of each channel.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K/L] to select “CHANNEL”, then press
[ENTER].
3 Use [Cursor K/ L] to select “Antenna”, then press
[ENTER].
Channel
Autoscan
Channel List
Manual Register
Antenna
4 Use [the Number buttons] or [CH K/L] to select the
channel for which you want to check the signal strength.
11
Antenna
Back
Now
0 Peak
CH
0
Ch Change
• If the channel is set to external input, you cannot
confirm the antenna condition.
Video1
Antenna
Back
Indicator is available
for antenna signal only.
CH
5 Press [SETUP] to exit.
22
EN
Ch Change
Cursor s
You can adjust brightness, contrast, color, tint and sharpness.
INTRODUCTION
5 Picture Adjustment
Cursor B
Brightness
Brightness
Move
ENTER
Move
ENTER
Enter
Move
ENTER
Enter
Move
ENTER
Enter
Move
ENTER
Enter
Enter
to decrease
brightness
to increase
brightness
to decrease
contrast
to increase
contrast
to decrease
color
to brighten
color
to add red
to add green
to make soft
to make clear
CONNECTION
1 Press [SETUP] to display the main menu.
30
Adjust
Contrast
Contrast
60
Adjust
2 Use [Cursor K/L] to select “PICTURE”, then press
Color
Color
[ENTER].
36
Adjust
INITIAL SETTING
Tint
Tint
0
Adjust
Sharpness
Sharpness
0
Adjust
then press [ENTER].
Reset Settings
Use [Cursor K / L] to select “Reset”, then press [ENTER]
to restore the “Picture Mode” setting to default.
Picture
Picture Mode
Reset Settings
Dynamic
This function resets the
"Dynamic" setting for Picture Mode
to factory default.
30
Brightness
60
Color
36
Tint
Cancel
Reset
OPTIONAL SETTING
Contrast
0
Sharpness
0
Reset Settings
Color Temp.
Neutral
Off
Energy Saving
4 Adjust the picture quality.
Color Temp.
Use [Cursor K / L] to select the desired setting, then
press [ENTER]. (Cool, Neutral and Warm)
TROUBLESHOOTING
Picture Mode
Use [Cursor K / L] to select the desired setting, then
press [ENTER]. (Standard, Dynamic, Movie and News)
Picture
Picture Mode
Brightness
Contrast
Picture
Color
Picture Mode
Standard
Brightness
Dynamic
Contrast
Movie
Color
News
Tint
Sharpness
Tint
Reset Settings
Cool
Color Temp.
Neutral
Energy Saving
Warm
Reset Settings
Energy Saving
Energy Saving
Use [Cursor s / B] to adjust the brightness of the backlight.
Brightness, Contrast, Color, Tint, Sharpness
Use [Cursor s / B] to adjust.
INFORMATION
Sharpness
Color Temp.
WATCHING TV
3 Use [Cursor K/L] to select the item you want to adjust,
: To brighten
Energy Saving Off
Adjust
ENTER
Enter
: To darken
Note:
• To cancel picture adjustment, press [SETUP].
5 Press [SETUP] to exit.
23
EN
OPTIONAL SETTING
5 Closed Caption
You can view closed captioning (cc) for TV programs, movies and news.
Closed caption refer to text of dialogue or descriptions displayed on-screen
for the hearing impaired.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K/L] to select “DETAIL”, then press
[ENTER].
3 Use [Cursor K/L] to select “Closed Caption”, then
[Caption Mode]
CC1 and Text1;
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
(up to 4 lines of script on the TV screen, where it
does not obstruct relevant parts of the picture).
CC3 and Text3;
serve as the preferred data channels.
The captioning or text is often a secondary language.
CC2, CC4, Text2 and Text4;
are rarely available and broadcasters use them only
in special conditions, such as when “CC1” and “CC3”
or “Text1” and “Text3” are not available.
• There are 3 display modes according to programs:
Paint-on mode:
Displays input characters on the TV screen
immediately.
Pop-on mode:
Once characters are stored in memory, they are
displayed all at once.
Roll-up mode:
Displays the characters continuously by scrolling
(max. 4 lines).
press [ENTER].
6 Press [SETUP] to exit.
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Note:
4 Use [Cursor K/L] to select “Conventional CC”, then
press [ENTER].
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
5 Use [Cursor K/L] to select the desired closed caption,
then press [ENTER].
Closed Caption
Conventional CC
Off
DTV CC
CC1
CC Style
CC2
CC3
CC4
Text1
Text2
Text3
Text4
24
EN
• To show the closed caption on your TV screen, broadcast
signal must contain the closed caption data.
• Not all TV programs and commercials have the closed
caption or all types of the closed caption.
• Captions and texts may not match the TV voice exactly.
• Changing channels may delay the closed caption for a few
seconds.
• Adjusting or muting the volume may delay the closed
caption for a few seconds.
• Abbreviations, symbols and other grammatical shortcuts
may be used in order to keep pace with the on-screen
action. This is not a problem with the unit.
• The caption or text characters will not be displayed while
the main menu or functions display is shown.
• If a black box appears on the TV screen, this means that
the closed caption is set to TEXT mode. To clear the box,
select “CC1”, “CC2”, “CC3”, “CC4” or “Off”.
• If the unit receives poor quality television signals, the
captions may contain errors, or there might be no captions
at all. Some possible causes of poor quality signals are:
- Automobile ignition noise
- Electric motor noise
- Weak signal reception
- Multiplex signal reception (ghosts or screen flutter)
• The unit retains the closed caption setting if the power
fails.
• Closed caption will not be displayed when you are using
an HDMI connection.
• When the unit receives a special effects playback signal
(i.e., Search, Slow and Still) from a VCR’s video output
channel (CH3 or CH4), the unit may not display the correct
caption or text.
INTRODUCTION
5 DTV Closed Caption
DTV
CONNECTION
In addition to the basic closed caption described on page 24, DTV has its
own closed caption called DTV CC. Use this menu to change the settings for
DTV CC.
5 Use [Cursor K/L] to select the desired DTV closed
1 Press [SETUP] to display the main menu.
caption, then press [ENTER].
INITIAL SETTING
Closed Caption
Conventional CC
2 Use [Cursor K/L] to select “DETAIL”, then press
DTV CC
Off
CC Style
Service1
Service2
Service3
Service4
[ENTER].
Service5
Service6
Service1~6
Select one of these before
changing any other item
in “Closed Caption” menu.
Choose “Service1” under
normal circumstances.
DTV CC
3 Use [Cursor K/L] to select “Closed Caption”, then
OPTIONAL SETTING
Select if you do not want
DTV CC. This is the default.
WATCHING TV
Off
press [ENTER].
6 Press [SETUP] to exit.
Detail
Closed Caption
V–chip
HDMI Audio
Auto
TROUBLESHOOTING
Note:
• “DTV CC” that you can switch differs depending on the
broadcast description.
4 Use [Cursor K/L] to select “DTV CC”, then press
[ENTER].
INFORMATION
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
25
EN
OPTIONAL SETTING
5 CC Style
You can change the style of CC such as font, color or size, etc.
6 Use [Cursor K/L] to select “On”, then press [ENTER].
1 Press [SETUP] to display the main menu.
CC Style
Closed Caption
User Setting
On
Font Style
Off
Font Size
Font Color
Font Opacity
2 Use [Cursor K/L] to select “DETAIL”, then press
Back Color
Back Opacity
Edge Color
[ENTER].
Edge Type
7 Use [Cursor K/L] to select an item, then press
[ENTER]. Then use [Cursor K / L] to select the desired
setting and press [ENTER].
Picture display
3 Use [Cursor K/L] to select “Closed Caption”, then
press [ENTER].
Edge
(Edge Color and Edge Type)
Detail
Closed Caption
V–chip
HDMI Audio
ABCDEFGHIJKL
Auto
Font
(Font Style, Font Size, Font Color and Font Opacity)
Back
(Back Color and Back Opacity)
• The setting description for each item is shown below.
4 Use [Cursor K/L] to select “CC Style”, then press
[ENTER].
[Font Style]
Closed Captioning font style can be changed as below.
CC Style
Closed Caption
User Setting
Font Style
Font Size
Closed Caption
Font Color
Conventional CC
Off
Font Opacity
DTV CC
Off
Back Color
Back Opacity
CC Style
Edge Color
Edge Type
[Font Size]
Font size of the displayed caption can be switched as
below.
5 Use [Cursor K/L] to select “User Setting”, then press
[ENTER].
CC Style
Font Style
Font Size
Large
Font Color
Middle
Font Opacity
Small
Back Color
Back Opacity
CC Style
26
EN
User Setting
Off
Font Style
Font0
Font Size
Middle
Font Color
White
Font Opacity
Solid
Back Color
Black
Back Opacity
Solid
Edge Color
Black
Edge Type
None
Closed Caption
User Setting
Edge Color
Edge Type
INTRODUCTION
CC Style
[Edge Type]
Edge type of the displayed caption can be switched as
below.
CC Style
Closed Caption
Closed Caption
User Setting
User Setting
White
Font Style
Font Size
Black
Font Size
Red
Font Color
None
Font Opacity
Green
Font Opacity
Raised
Back Color
Blue
Back Color
Depressed
Back Opacity
Yellow
Back Opacity
Uniform
Edge Color
Magenta
Edge Color
L.Shadow
Edge Type
Cyan
Edge Type
R.Shadow
[Font Opacity]
Font opacity of the displayed caption can be switched
as below.
INITIAL SETTING
Font Style
Font Color
CC Style
CONNECTION
[Font Color]
Font color of the displayed caption can be switched as
below.
8 Press [SETUP] to exit.
Closed Caption
WATCHING TV
User Setting
Font Style
Font Size
Font Color
Font Opacity
Solid
Back Color
Flash
Back Opacity
Translucent
Edge Color
Transparent
Edge Type
CC Style
OPTIONAL SETTING
[Back Color]
Background color of the displayed caption can be
switched as below.
Closed Caption
User Setting
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Blue
Yellow
Edge Color
Magenta
Edge Type
Cyan
TROUBLESHOOTING
Back Color
Back Opacity
[Back Opacity]
Background opacity of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
INFORMATION
Font Style
Font Size
Font Color
Font Opacity
Back Color
Solid
Back Opacity
Flash
Edge Color
Translucent
Edge Type
Transparent
[Edge Color]
Edge color of the displayed caption can be switched as
below.
CC Style
Closed Caption
User Setting
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Back Color
Blue
Back Opacity
Yellow
Edge Color
Magenta
Edge Type
Cyan
27
EN
OPTIONAL SETTING
5 V-chip
See the following description for setting each item.
V-chip reads the ratings for programs, then denies access to the programs
which exceed the rating level you set. With this function, you can block
certain programming inappropriate for children.
V-chip
MPAA Rating
A
TV Rating
B
Downloadable Rating
Clear Downloadable Rating
New Password
1
C
Press [SETUP] to display the main menu.
A... “A. MPAA Rating”D page 29
B... “B. TV Rating”D page 29.
2 Use [Cursor K/L] to select “DETAIL”, then press
C... “C. New Password” D page 30
[ENTER].
Note:
• When you select a rating and set it to “Block”, the higher
ratings will be blocked automatically. The lower ratings
will be available for viewing.
• When you set the highest rating to “View”, all ratings turn
to “View” automatically.
• To block any inappropriate programming, set your limits in
“MPAA Rating”, “TV Rating” and “Downloadable Rating”.
• The V-chip setting will be retained after a power failure
(except the access code reverts to 0000).
• If the rating is blocked, will appear.
• “Downloadable Rating” will be available when the unit
receives a digital broadcast using the new rating system.
• If the broadcasting signal does not have the downloadable
rating information, “Downloadable Rating is currently not
available.” will appear.
This message will also appear when you try to access
“Downloadable Rating” after you have cleared the
downloadable rating information, and the new
information has not been downloaded since.
• To clear the downloadable rating information and its
setting, select “Clear Downloadable Rating”.
3 Use [Cursor K/L] to select “V-chip”, then press
[ENTER].
Detail
Closed Caption
V–chip
HDMI Audio
Auto
4 Use [the Number buttons] to enter the 4-digit
numbers for your password.
V-chip
-
Enter password.
PIN Code
BACK
Back
• When you have not set up your password, enter
0000.
• When the password is correct, the “V-chip” menu is
displayed.
28
EN
INTRODUCTION
A. MPAA Rating
B. TV Rating
MPAA Rating is the rating system created by MPAA (Motion Picture
Association of America).
[ENTER].
5 Use [Cursor K/L] to select “TV Rating”, then press
[ENTER].
V-chip
V-chip
MPAA Rating
TV Rating
TV Rating
Downloadable Rating
Downloadable Rating
Clear Downloadable Rating
Clear Downloadable Rating
New Password
New Password
6 Use [Cursor K/L/s/B] to select the desired rating,
then press [ENTER] repeatedly to switch between
“View” and “Block”.
V-chip
V-chip
FV V
X
NC-17
R
PG-13
PG
G
NR
ENTER
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
View/Block
BACK
Select
Back
Category
Mature audience only
NC-17
No one under 17 admitted
R
Restricted; under 17 requires accompanying
parent or adult guardian
PG-13
Unsuitable for children under 13
PG
Parental guidance suggested
G
General audience
NR
No rating
BACK
Back
7 Press [SETUP] to exit.
[To Set the Sub Ratings]
As for TV-MA, TV-14, TV-PG, or TV-Y7, you can further
set the sub ratings to block specific elements of
programming. To set the sub ratings, follow the step
below.
Use [Cursor K / L / s / B] to select the desired rating,
then press [ENTER] repeatedly to switch between
“View” and “Block”.
INFORMATION
Press [SETUP] to exit.
View/Block
TROUBLESHOOTING
X
ENTER
OPTIONAL SETTING
Select
7
WATCHING TV
press [ENTER] repeatedly to switch between “View”
and “Block”.
INITIAL SETTING
MPAA Rating
6 Use [Cursor K/L] to select the desired rating, then
Rating
CONNECTION
5 Use [Cursor K/L] to select “MPAA Rating”, then press
V-chip
FV V
Note:
• Changing the category to “Block” or “View” automatically
changes all its sub ratings to the same (“Block” or “View”).
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Select
ENTER
View/Block
BACK
Back
29
EN
OPTIONAL SETTING
Rating
C. New Password
Category
TV-MA
Mature audience only
TV-14
Unsuitable for children under 14
TV-PG
Parental guidance suggested
TV-G
General audience
TV-Y7
TV-Y
higher
Although the default code “0000” is supplied with the unit, you can set
your own password.
5 Use [Cursor K/L] to select “New Password”, then press
[ENTER].
Appropriate for all children 7 and
older
Appropriate for all children
V-chip
MPAA Rating
TV Rating
lower
Downloadable Rating
Clear Downloadable Rating
New Password
Sub Rating
Category
Rating
FV
Fantasy Violence
TV-Y7
V
Violence
S
Sexual Situation
L
Coarse Language
TV-PG
TV-14
TV-MA
D
Suggestive Dialogue
TV-PG, TV-14
6 Press [the Number buttons] to enter the new 4-digit
password.
• Enter password again in “Confirm password.” entry
field.
Note:
V-chip
• Blocked sub rating will appear beside the main rating
category in “TV Rating” menu.
• You cannot block a sub rating (D, L, S or V) if the main
rating is set to “View”.
• Changing the category to “Block” or “View” automatically
changes all its sub ratings to the same (“Block” or “View”).
Enter password.
Confirm password.
PIN Code
- - - - - - BACK
Back
7 Press [SETUP] to exit.
Note:
• Make sure new password and confirm password must be
exactly the same. If they are different, the space is cleared
for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs. If you forget the
password, unplug the power cord for 10 seconds to restore
the password to 0000.
30
EN
INTRODUCTION
5 HDMI Audio
You can set the method of sound input for the HDMI - IN jack.
CONNECTION
1 Press [SETUP] to display the main menu.
2 Use [Cursor K/L] to select “DETAIL”, then press
INITIAL SETTING
[ENTER].
WATCHING TV
3 Use [Cursor K/L] to select “HDMI Audio”, then press
[ENTER].
Detail
OPTIONAL SETTING
Closed Caption
V–chip
HDMI Audio
Auto
TROUBLESHOOTING
4 Use [Cursor K/L] to select the desired sound input,
then press [ENTER].
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Digital
Analog
INFORMATION
Auto
HDMI
Audio
Digital
Analog
Select if you have connected both
digital device to the HDMI - IN jack
and analog device to the audio
sources. Digital audio input signal
will have priority.
Select if you have connected
digital device to the HDMI - IN jack
for digital audio input signal.
Select if you have connected
analog device to the analog audio
jacks for analog audio input signal.
5 Press [SETUP] to exit.
31
EN
TROUBLESHOOTING
5 Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once
before calling for service.
Symptom
Remedy
No power
• Be sure the power cord is plugged in.
• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
reset itself.
No picture or sound
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on again.
No color
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Adjust the “Color” in the main menu.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• Adjust “Contrast” and “Brightness” in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Adjust “Contrast” and “Brightness” in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture blurred
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Bars on screen
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on
screen
• Move the unit away from nearby electric appliances. Turn off the power and wait
30 minutes before turning it back on.
• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some
channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor
• View other TV channels. The problem might be limited to the broadcasting station.
No reception of digital signals
• Make sure auto channel scan has been completed (Refer to “Auto Channel Scan” on
page 13).
Auto channel scan must be completed when you set up the unit for the first time
or move it to a location where previously unavailable channels are broadcast.
• The selected channel may not be broadcasting.
• When auto channel scan is interrupted and not completed, some channels will not
be received. Make sure to complete (Refer to “Auto Channel Scan” on page 13).
32
EN
INTRODUCTION
Remote control does not work
• Check the antenna or cable connection to the main unit.
• Check the batteries of the remote control.
• Check if there is an obstacle between the infrared sensor window and the remote
control.
• Test the signal output. If OK, then possible infrared sensor trouble.
(Refer to “IR Signal Check” on page 34.)
• Aim the remote control directly at the infrared sensor window on the front of the
unit.
• Reduce the distance to the unit.
• Re-insert the batteries with their polarities (+/– signs) as indicated.
• When there is an infrared-equipped device such as PC near this unit, it may
interrupt the remote control signal of this unit.
Move the infrared-equipped device away from this unit, change the angle of the
infrared sensor or turn off the infrared communication function.
WATCHING TV
• Many digital channels have alternate channel numbers. The unit changes the
numbers automatically to the ones signifying the broadcasting stations. These are
the numbers used for analog broadcasts.
INITIAL SETTING
Remedy
The entered channel number
changes automatically
CONNECTION
Symptom
Problems with Closed Caption Feature
Captions are not entirely
displayed, or captions are
delayed behind the dialogue.
• Captions that are delayed a few seconds behind the actual dialogue are common
for live broadcasts. Most captioning production companies can display a dialogue
to a maximum of 220 words per minute. If a dialogue exceeds that rate, selective
editing is used to insure that the captions remain up-to-date with the current TV
screen dialogue.
Captions are displayed as a
white box.
No caption is displayed in the
closed caption-supported
program.
• Interference from buildings or weather conditions may cause captioning to be
incomplete.
• Broadcasting station may shorten the program to insert advertisement. The closed
caption decoder cannot read the information of the shortened program.
No caption is displayed
when playing the videotape
containing captions.
• The videotape may be illegally copied, or the caption signal might not have been
read during copying.
Black box is displayed in the
TV screen.
• “Text” mode is selected for caption. Select “CC1”, “CC2”, “CC3”, “CC4”or “Off”.
TROUBLESHOOTING
• Closed captioning production companies may broadcast programs without
correcting the misspelling in a live broadcast.
OPTIONAL SETTING
Misspelled captions are
displayed.
INFORMATION
Note:
• The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a fixed point of
blue, green or red. This is not to be considered a defect in the LCD screen.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this owner’s manual for more
details on correct operations.
33
EN
INFORMATION
5 Glossary
ATSC
Dolby Digital
Password
Acronym that stands for Advanced
Television Systems Committee and
the name of the digital broadcasting
standards.
The system developed by Dolby
Laboratories to compress digital
sound. It offers stereo sound (2ch) or
multi-channel audio.
A stored 4-digit number that allows
access to parental control features.
Aspect Ratio
HDMI (high-definition multimedia
interface)
The width of a TV screen relative to its
height. Conventional TVs are 4:3 (in
other words, the TV screen is almost
square); widescreen models are 16:9
(the TV screen is almost twice as wide
as its height).
Interface that supports all
uncompressed, digital audio/video
formats including set-top box, DVD
player or digital television, over a
single cable.
SAP (secondary audio program)
Second-audio channel delivered
separately from main-audio channel.
This audio channel is used as an
alternate in bilingual broadcasting.
SDTV (standard definition TV)
Standard digital format that is similar
to the NTSC picture quality.
S-video
Component Video
HDTV (high definition TV)
This is a video signal format that
conveys each of 3 principal colors of
light (red, blue and green) through
different signal lines. This allows the
viewers to experience picture colors
as original as it is. There are several
signal formats, including Y / Pb / Pr
and Y / Cb / Cr.
Ultimate digital format that produces
high resolution and high picture
quality.
NTSC
Offers higher quality images by
delivering each signal, color (c) and
luminance (y) independently of each
other through separate cables.
Acronym that stands for National
Television Systems Committee and
the name of the current analog
broadcasting standards.
5 Maintenance
Cabinet Cleaning
• Wipe the front panel and other exterior surfaces of the unit with a
soft cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near
the unit. Such chemicals may cause damage and discoloration to
the exposed surfaces.
Panel Cleaning
Wipe the panel of the unit with a soft cloth. Before cleaning the
panel, disconnect the power cord.
IR Signal Check
If the remote control is not working properly, you can use an AM
radio or digital camera (including a cellular phone with built-in
camera) to see if it is sending out an infrared signal.
• With an AM radio:
Tune the AM radio station to a nonbroadcasting frequency. Point the remote
control towards it, push any button and
listen. If the sound from the radio flutters,
it is receiving the remote control’s infrared
signal.
Servicing
Should your unit become inoperative, do not try to correct the
problem yourself. There are no user serviceable parts inside. Turn
off the unit, unplug the power cord and call our toll free customer
support line found on the cover of this manual to locate an
authorized service center.
34
EN
• With a digital camera
(including built-in cell phone cameras):
Point a digital camera towards the remote control.
Push any button on the remote control and look
through the digital camera. If the infrared light
appears through the camera, the remote control is
working.
INTRODUCTION
5 Cable Channel Designations
If you subscribe to cable TV, the channels are displayed as 1-135.
Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company.
The following is a chart of common cable channel designations.
TV Display
3
3
K
24
W+9
45
W+30
66
W+51
87
W+67
108
W+88
129
4
4
L
25
W+10
46
W+31
67
W+52
88
W+68
109
W+89
130
5
5
M
26
W+11
47
W+32
68
W+53
89
W+69
110
W+90
131
6
6
N
27
W+12
48
W+33
69
W+54
90
W+70
111
W+91
132
7
7
O
28
W+13
49
W+34
70
W+55
91
W+71
112
W+92
133
8
8
P
29
W+14
50
W+35
71
W+56
92
W+72
113
W+93
134
9
9
Q
30
W+15
51
W+36
72
W+57
93
W+73
114
W+94
135
10
10
R
31
W+16
52
W+37
73
W+58
94
W+74
115
11
11
S
32
W+17
53
W+38
74
A-5
95
W+75
116
12
12
T
33
W+18
54
W+39
75
A-4
96
W+76
117
13
13
U
34
W+19
55
W+40
76
A-3
97
W+77
118
A
14
V
35
W+20
56
W+41
77
A-2
98
W+78
119
B
15
W
36
W+21
57
W+42
78
A-1
99
W+79
120
C
16
W+1
37
W+22
58
W+43
79
W+59
100
W+80
121
D
17
W+2
38
W+23
59
W+44
80
W+60
101
W+81
122
E
18
W+3
39
W+24
60
W+45
81
W+61
102
W+82
123
F
19
W+4
40
W+25
61
W+46
82
W+62
103
W+83
124
5 Electrical Specification
TV format:
ATSC / NTSC-M TV standard
Closed caption system:
§15.122/FCC (digital CC) §15.119/FCC (analog CC)
Channel coverage (ATSC/NTSC):
Terrestrial
VHF: 2~13 UHF: 14~69
CATV
2~13, A~W, W+1~W+94 (analog W+1~W+84),
A-5~A-1, 5A
Tuning system: Channel frequency synthesized tuning system
Channel access: Direct access keyboard,
Programmable scan, and up/down
Terminals:
Antenna input: VHF/UHF/CATV
75Ω unbalanced (F-type)
S-video input: Mini DIN 4-pin jack x 2 Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
Video input: RCA jack x 2
1Vp-p (75Ω)
Audio input: RCA jack (L/R) x 10
2V rms
(input impedance: more than 22kΩ)
Component video input:
RCA jack x 6
Y: 1Vp-p (75Ω)
Pb: 700mVp-p (75Ω)
Pr: 700mVp-p (75Ω)
HDMI input: HDMI 19pin x 1
Coaxial digital audio output:
RCA jack x1
500mVp-p (75Ω)
Analog audio output:
RCA jack x2
Sound output: 5W, 16Ω x 2
H
21
W+6
42
W+27
63
W+48
84
W+64
105
W+85
126
WATCHING TV
5 General Specifications
G
20
W+5
41
W+26
62
W+47
83
W+63
104
W+84
125
INITIAL SETTING
2
2
J
23
W+8
44
W+29
65
W+50
86
W+66
107
W+87
128
CONNECTION
5A
1
CATV channel
I
TV Display
22
CATV channel W+7
TV Display
43
CATV channel W+28
TV Display
64
CATV channel W+49
TV Display
85
CATV channel W+65
TV Display
106
CATV channel W+86
TV Display
127
CATV channel
5 Other Specifications
OPTIONAL SETTING
Remote control: Digital encoded infrared light system
Operating temperature:
41°F (5°C) to 104°F (40°C)
Power requirements:
120V AC +/- 10%, 60Hz +/- 0.5%
Power consumption (maximum):
165W
LCD:
32 inches wide XGA panel
Dimensions:
<Without stand>
W: 32.3 inches (818mm)
H: 23.5 inches (595mm)
D: 4.8 inches
(121mm)
<With stand>
W: 32.3 inches (818mm)
H: 25.4 inches (644mm)
D: 10.9 inches (275mm)
Weight:
32.0 lbs.
(14.5kg)
TROUBLESHOOTING
INFORMATION
• Designs and specifications are subject to change without notice and
without our legal obligation.
• If there is a discrepancy between languages, the default language will
be English.
35
EN
TM
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
LABOR:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year
from the date of original retail purchase. Certain parts and LCD image burn-in are excluded
from this warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the
date of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO
OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,
missing or if service was attempted by an unauthorized service center. This limited warranty does not
apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during
normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs,
alterations or products not supplied by FUNAI CORP., or damage, which results from accident, misuse,
abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use
such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or
other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL),
ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING
THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY
DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO
PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE
CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY
FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN
SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its
original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE
CENTER. FUNAI CORP. will not reimburse you for any service done by unauthorized service providers
without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact us at:
FUNAI CORPORATION
Customer Service
Tel : 1-800-256-2487
http://www.EmersonAudioVideo.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in China
A71F3UH/A71F5UH
1EMN22139 *****