Audiovox VM9511TS Instruction manual

VM9511TS
Instruction Manual
Manual de Instrucciones
Guide d'instructions
CONTENTS
TABLE DES MATIÈRES
Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s
manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to
use all the features of your new Jensen VM9511TS Mobile Multimedia AM/FM/DVD Receiver
for maximum enjoyment.
Merci d'avoir choisi un produit Jensen . Nous espérons que vous allez trouver les instructions
dans ce guide de propriétaire claires et faciles à suivre . Prenez quelques minutes à le
consulter, vous apprendrez à utiliser toutes les fonctions de votre nouvelle radio Jensen pour
en tirer une jouissance maximum.
Preparation............................................................................................................................ 1
Installation ............................................................................................................................. 5
Controls and Indicators ......................................................................................................... 6
Front Zone Remote Control .................................................................................................. 9
Multi-ZONE Remote Control ............................................................................................... 12
Using the TFT Monitor ........................................................................................................ 13
Operating Instructions ......................................................................................................... 15
System Setup Menu............................................................................................................ 16
Multi-ZONE Operation......................................................................................................... 18
Tuner Operation .................................................................................................................. 19
XM Radio Operation............................................................................................................ 20
DVD/VCD Video Operation ................................................................................................. 22
DVD/Disc Setup Menu ........................................................................................................ 25
DVD/Disc Audio Operation.................................................................................................. 28
SD Card Reader Operation................................................................................................. 30
iPod Operation .................................................................................................................... 31
TV Tuner Operation ............................................................................................................ 32
Navigation System .............................................................................................................. 33
Troubleshooting .................................................................................................................. 34
Specifications ...................................................................................................................... 37
12-month Limited Warranty .................................................................................................37
Preparation......................................................................................................................... 77
Installation .......................................................................................................................... 81
Controles et indicateurs...................................................................................................... 82
Telecomande de la zone d'avant ....................................................................................... 85
Telecommande Multi-ZONE............................................................................................... 88
Utilisation du moniteur TFT ................................................................................................ 89
Instructions d'operation ...................................................................................................... 91
Menu configuration du systeme ......................................................................................... 93
Operation Multi-ZONE........................................................................................................ 95
Operation tuner AM/FM...................................................................................................... 96
Operation radio XM ............................................................................................................ 97
Operation platine DVD ....................................................................................................... 99
Menu de configuration DVD/disque.................................................................................. 102
Operation audio DVD/DisQUE ......................................................................................... 105
Operation lecteur carte SD............................................................................................... 107
Operation iPod ................................................................................................................. 108
Operation tuner TV........................................................................................................... 109
Systeme de navigation ..................................................................................................... 110
Depannage....................................................................................................................... 111
Specifications ................................................................................................................... 114
Garantie limitée de 12 mois .............................................................................................. 114
CONTENIDO
Gracias por elegir los productos Jensen. Esperamos que encuentre en este manual
instrucciones claras y fáciles de seguir. Si se toma unos pocos minutos para leerlo, aprenderá
cómo utilizar todas las funciones de su nuevo radio Jensen para su máximo entretenimiento.
Preparación......................................................................................................................... 39
Instalación ........................................................................................................................... 43
Controles e Indicadores ...................................................................................................... 44
Control Remoto de Zona Delantera .................................................................................... 47
Control Remoto de Multi-ZONE .......................................................................................... 50
Utilización del Monitor TFT ................................................................................................. 51
Instrucciones de Operación ................................................................................................ 53
Menú de Configuración de Sistema .................................................................................... 55
Operación Multi-ZONE........................................................................................................ 57
Operación del Radio ........................................................................................................... 58
Operación de Radio XM® .................................................................................................... 59
Operación del Video de DVD/VCD ..................................................................................... 61
Menú Configuración del DVD/Disc...................................................................................... 64
Operación del Audio de DVD/Disco .................................................................................... 67
Operación del Lector de Tarjeta SD.................................................................................... 69
Operación de iPod .............................................................................................................. 70
Operación del Sintonizador de TV ...................................................................................... 71
Sistema de Navegación ...................................................................................................... 72
Solución de Problemas ....................................................................................................... 73
Especificaciones ................................................................................................................. 76
Garantia Limitade de 12 Meses .......................................................................................... 76
i
VM9511TS
PREPARATION
Congratulations on your purchase of the Jensen VM9511TS
Mobile Multimedia AM/FM/DVD Receiver.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen
VM9511TS installed by a reputable installation shop.
Features
DVD
• Compatible formats: DVD-R, DVD-RW, DVD+R,
DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD,
VCD, MPEG2, MPEG4, AVI and JPEG
• Region 1 playback
• 16:9 Aspect ratio- Wide / Normal / Cinema
• Front panel DVD control
• High-speed Fast Forward / Fast Rewind 2X, 4X, 8X, 32X
• Play, Pause, Stop, Slow
• Chapter Up / Down
• V-SEL - MultiZone output 'Kid-Zone'
• Wolfson Microelectronics high performance 24-bit, 192
kHz DAC supports 6-channel and 2-channel "Down-Mix”
audio modes
• 16MB high-speed flash memory - 80nS access time
• 2 second ESP (Electronic Skip Protection)
Integrated SD Card Reader
• Compatible formats: MP3, WMA, AVI, MPEG1, MPEG2,
MPEG4 and JPEG
• Supports up to 2GB SD card
MP3/WMA
• GIGA MP3 - Store up to 999 MP3 files on a DVD
• ID3-tag compatible
• Direct track access
• Play, Pause, Stop, Track Up / Down
• 60 second (MP3), 120 second (WMA) ESP - Electronic
Skip Protection
CD
• CD-text compatible
• 4 second ESP (Electronic Skip Protection)
AM/FM Tuner
• User-selectable frequency spacing
• 30 Station presets (18FM/12AM) JENSEN Plus Tuner II
Outboard Media Module
• Input adapter for TV Tuner, XM and iPod
TV Tuner (Included)
• VHF 2-13
• UHF 14-69
• TV antenna (3.5mm antenna included)
• F-Connector/Coaxial Antenna Input (optional)
XM Ready
• Requires optional Terk XMD1000 tuner box
• Requires optional Terk XMDJEN100 or Jensen JXMC XM
cables
• Advanced display shows the artist, song title, and XM
channel and category at a glance
• Direct channel entry
Navigation Ready
• Requires optional NAV100 navigation module
jLink Ready
• Controls and charges all iPod's except "Shuffle"
• Displays all text information including category, track
name, artist and channel number
Chassis
• 7-inch TFT touch screen LCD - 336,960 pixels (1440W X
234H)
• TSD - Touch Screen Display menu control
• Fully automatic motorized TFT LCD flip-out and up
• 16-step TFT LCD tilt adjustment
• Beep Tone confirmation
• 1.0 Din
• Import/ISO/DIN mountable
• Heat management system - Incorporates forced aircooling to keep the chip-sets operating at nominal
temperatures
• Heavy duty galvanized chassis
Multi-ZONE
• Allows front passengers to listen to the radio while rear
passengers listen to a CD, MP3, WMA or watch DVDs
General
• Full function infrared remote control
• Limited function infrared "Kid Zone" remote
• OSD - On Screen Display menu control
• High-performance audio processor
• Electronic volume, bass, treble, balance and fader
• Bass center frequency adjustment - 60, 80, 100, 130,
150 and 200Hz
• Bass Q factor - 1.0, 1.25, 1.5 and 2.0
• Treble center frequency adjustment - 10, 12.5, 15 and
17kHz
• Subwoofer crossover - 80, 120 and 160Hz
• Subwoofer Phase - 0 - 180 degrees
• Subwoofer level - variable
• 100-ohm low impedance pre-amp outputs, all channels
• 5V Peak / 2V RMS RCA outputs, all channels
• 1-pair front RCA outputs and 1-pair rear/surround RCA
outputs
1
•
•
•
•
•
•
•
•
•
•
Single Subwoofer RCA output
Center Channel RCA pre-amp output (variable)
1-pair headphone/Multi-ZONE RCA outputs
1-pair auxiliary RCA A/V inputs
Back-up camera input with reverse override
1 NTSC composite video output for additional screens
NTSC Multi-ZONE composite video for additional screens
Front panel (when screen is closed) high contrast LCD
Rotary encoder audio control
Joystick menu navigation
Tools and Supplies
You will need these tools and supplies to install your
VM9511TS:
•
•
•
•
•
•
•
•
•
Torx type, flat-head and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
WARNING! To reduce the risk of a traffic accident
(except when using for rear-view video camera) never
use the video display function while driving the vehicle.
This is a violation of federal law.
WARNING! Never disassemble or adjust the unit without
the assistance of a professional. For details, please
consult your local car stereo specialty shop.
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
VM9511TS
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
WARNING! Do not change the fuse on the power wire
without professional guidance. Using an improper fuse
may cause damage to the unit and result in a fire.
WARNING! The monitor employs an automatic motorized
mechanism. To prevent damage to the core mechanism,
please do not push, pull or swivel the monitor manually.
Optional Accessories
iAUX3 READY (Sold Separately)
•
Can connect to any portable media device or multimedia
device using a standard 3.5mm plug
•
Converts 3.5mm auxiliary input to RCA stereo outputs
for easy connection to the radio’s AUX inputs
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and
remove the negative (-) battery cable prior to installation.
NOTE: If the VM9511TS is to be installed in a vehicle
equipped with an on-board drive or navigation computer,
DO NOT disconnect the battery cable. If the cable is
disconnected, the computer memory may be lost. Under
these conditions, use extra caution during installation to
avoid causing a short circuit.
2
VM9511TS
WIRING DIAGRAM
3
VM9511TS
WIRING DIAGRAM - MULTIMEDIA CONNECTIONS
*TERK XMDJEN100 cables (sold
separately)
**TERK XMD1000 Direct Tuner and
antenna (sold separately)
***NAV100 (sold separately)
4
VM9511TS
INSTALLATION
Pre-installation
1.
2.
Press the metal levers on both sides to remove the halfsleeve from the radio.
Remove the transport screws.
FINAL INSTALLATION
CAUTION! Be careful not to damage the car wiring.
4.
Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve.
Wiring
PREPARE RADIO
Complete wiring as illustrated in the wiring diagram on page
3. Once the wiring is complete, reconnect the battery
negative terminal. If there is no ACC available, connect the
ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct
type and amperage to avoid damaging the radio. The
VM9511TS uses one 15 amp mini-ATM fuse, located in
the black filter box in-line with the main wire harness.
3.
Install the half-sleeve.
a. Install adapter if necessary (optional).
b. Install half-sleeve into adapter or dashboard (use only
the supplied screws). Do not force the sleeve into the
opening or cause it to bend or bow.
c. Locate the series of bend-tabs along the top, bottom
and sides of the mounting sleeve. With the sleeve fully
inserted into the dashboard opening, bend as many of
the tabs outward as necessary so that the sleeve is
firmly secured to the dashboard.
d. Install support strap to make the unit more stable.
Final Installation
Final ISO-DIN Installation
After completing the wiring connections, turn the unit on to
confirm operation (ignition switch must be on). If unit does not
operate, recheck all wiring until problem is corrected. Once
proper operation is achieved, turn off the ignition switch and
proceed with final mounting of the chassis.
1.
Remove trim ring.
2.
Mount factory brackets on new radio using existing
screws from old radio.
1.
2.
3.
Connect wiring adapter to existing wiring harness.
Connect antenna lead.
Carefully slide the radio into the half-sleeve, making
sure it is right-side-up, until it is fully seated and the
spring clips lock it into place.
3.
Slide radio chassis into dash opening and secure.
4.
Reinstall dash panel.
FINAL ISO-DIN INSTALLATION
NOTE: For proper operation of the CD/DVD player, the
chassis must be mounted within 20° of horizontal. Make
sure the unit is mounted within this limitation.
INSTALL HALF SLEEVE
4.
3d
3c
3a
Attach one end of the perforated support strap
(supplied) to the screw stud on the rear of the chassis
using the hex nut provided. Fasten the other end of the
perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut
provided. Bend the strap to position it as necessary.
Using the iAUX3 External AV Connector
CAUTION! The rear of the radio must be supported with
the strap to prevent damage to the dashboard from the
weight of the radio or improper operation due to
vibration.
The iAUX3 (sold separately) allows you to connect a variety
of external devices, including a VCR, DVD player, portable
MP3 player, etc., to your VM9511TS without removing the
radio.
5.
To install the iAUX3, connect it to the AUX-IN cables on the
back of the VM9511TS (see the Wiring Diagram on page 3),
Replace any items you removed from the dashboard.
and then install the iAUX3 in a location convenient for
plugging in auxiliary devices.
3b
5
VM9511TS
CONTROLS AND INDICATORS
Button Operation
1. OPEN
Press to activate the automatic mechanical system and move
the TFT monitor into viewing position. Press again to close
the TFT.
2. WIDE/
PICTURE
Press to adjust the display aspect of the picture to one of
three settings: Cinema, Full, Normal or OFF. Press and hold
to access picture settings.
3. (
)
Press to adjust the upward tilt angle of the screen one step at
a time. Press and hold this button to continuously adjust the
upward tilt or picture settings.
4. (
)
Press to adjust the downward tilt angle of the screen one step
at a time. Press and hold this button to continuously adjust
the downward tilt or picture settings.
5. DISP
Press to display system information on the screen.
6. VOL/LO/DX
Rotate to adjust the volume. Press and release to enter and/
or confirm audio settings. Press and hold to activate the Local
(LOC) setting.
7. POWER/MUTE
Press once to turn the unit on. Press again to mute the
volume. Press and hold to turn the unit off.
8. 1/AUDIO
DVD Mode: Press to select audio language during playback.
TUNER Mode: Press once to play preset radio station
channel 1. Press and hold to store the current radio station in
preset channel 1.
9. 2/SUBTITLE
DVD Mode: Press once to select the subtitle language during
playback.
TUNER Mode: Press once to play preset radio station
channel 2. Press and hold to store the current radio station in
preset channel 2.
6
VM9511TS
CONTROLS AND INDICATORS
10. 3/SCN
DVD Mode: Press once to start scan playback.
TUNER Mode: Press once to play preset radio station
channel 3. Press and hold to store the current radio station in
preset channel 3.
11. 4/RPT
DVD Mode: Press once to start repeat playback.
TUNER Mode: Press once to play preset radio station
channel 4. Press and hold to store the current radio station in
preset channel 4.
12. 5/2-6CH/RDM
DVD Mode: Press once for random playback.
TUNER Mode: Press once to play preset radio station
channel 5. Press and hold to store the current radio station in
preset channel 5.
CD Mode: Press and hold to switch between 2 channel & 6
channel audio output.
13. 6/STOP
DVD Mode: Press once to stop playback.
19. (
TUNER Mode: Press once to play the preset radio station
channel 6. Press and hold to store the current radio station in
preset channel 6.
DVD Mode: Press once for slow forward/slow reverse.
14. BAND
TUNER Mode: Press to switch between FM and AM.
15. SRC
Press once to select playing mode.
Press and hold to toggle rear zone mode On/0ff.
16. (
)
DVD Mode: Press once to play back the previous chapter/
track.
TUNER Mode: Press once to auto-search for the previous
available radio station.
MENU Mode: Press once to move the cursor to the left.
17. (
)
DVD Mode: Press once to enter the next chapter or track.
TUNER Mode: Press once to auto-search the next available
radio station.
MENU Mode: Press once to move the cursor to the right.
18. (
)
)
TUNER Mode: Press to go down one frequency step.
MENU Mode: Press once to move the cursor down.
20. PLAY/ENTER
DVD Mode: Press once to start a playback.
Press once to confirm a selection.
21. (
)
Press once for disc insertion/ejection.
Press and hold to reset core mechanism position.
22. RESET
Press to reset system settings to factory default (except the
password and parental lock setting).
23. LCD Display
24. TFT Display
25. IR Remote Control Receiver
26. AS (Auto Store)
Press to automatically store strong radio stations in the six
preset channels in the current band.
27. SD Card Slot
DVD Mode: Press once for fast forward/fast reverse.
TUNER Mode: Press to go up one frequency step.
MENU Mode: Press once to move the cursor up.
7
VM9511TS
CONTROLS AND INDICATORS
LCD Display/Indicators
1. Disc Indicator
Illuminated when disc is loaded
2. DVD Playback Indicators (SCN/RPT/RDM/ALL)
The following DVD playback indicators become Illuminated
when the corresponding function is active:
•
•
•
•
SCN: scan playback
RPT: repeat playback
RDM: random playback
ALL: playback all chapters
1
2
3
3. Loudness Indicator (LOUD)
The loudness indicator becomes illuminated when the LOUD
function is activated.
4. Main Display
The main display is an 8 digit, 14 segment LCD which
displays the time, tuning frequency and other text
information.
5. Channel/Disc Display
The channel/disc display is a 2 digit, 7 segment LCD display
which displays the disc number or radio channel indicators
when the corresponding function is active:
•
•
CH: radio is activated
DISC: DVD mode is activated
6. Stereo/Local Indicator
The stereo/local indicator illuminates one of the following
indicators when the corresponding function is active:
•
•
ST: radio is in stereo mode
LOC: local radio station seeking function is activated
8
4
5
6
VM9511TS
FRONT ZONE REMOTE CONTROL
NOTE: Your remote control may differ slightly
from the one pictured here. The above diagram is
for illustrative purposes only.
9
VM9511TS
Table 1: Front Zone Remote Control Functions
Button
Name
Function
Ref#
DVD
VCD
TUNER
CD/MP3
TV
XM
Displays XM Setup Menu
iPod
MENU
1
Enters the main menu of
the disc
Turns on PBC when
playing VCD
Selects Photo mode
TITLE
2
Enters the title menu of
the disc
Plays first ten seconds of
each chapter/title
MUTE
3
Toggles on/off audio output
Toggles on/off audio output
Toggles on/off audio output
Toggles on/off audio output
Toggles on/off audio output
Toggles on/off audio output
Toggles on/off audio output
POWER/
4
Turns the power on/off
Turns the power on/off
Turns the power on/off
Turns the power on/off
Turns the power on/off
Turns the power on/off
Turns the power on/off
AUDIO
5
Changes the audio language for disc playback
REPT A-B
6
Setup to repeat playback
from time frame A to time
frame B
Setup to repeat playback
from time frame A to time
frame B
REPT
7
Repeats playback of current chapter
Repeats playback of current chapter
SRC
8
Selects playing mode
Selects playing mode
Selects playing mode
Selects playing mode
SUBTITLE
9
Language selection for
subtitle
INFO
10
Displays playing information
Displays playing information
Displays playing information
ANGLE
11
Continuously adjusts
front panel tilt angle
Continuously adjusts
front panel tilt angle
ANGLE
12
Continuously adjusts
front panel tilt angle
Continuously adjusts
front panel tilt angle
ANGLE
13
Plays back disc in different angle for a scene
Plays back Picture CD
with different angle of
picture displayed
14
Fast forwards the disc
content
Fast forwards the disc
content
Selects Music mode
Selects Video mode
Repeats playback of current track
Selects Category Mode
Repeats playback of current track
Selects playing mode
Selects playing mode
Selects playing mode
Display playing information
Displays playing information
Displays playing information
Displays playing information
Continuously adjusts
front panel tilt angle
Continuously adjusts
front panel tilt angle
Continuously adjusts
angle of TFT screen
Continuously adjusts
angle of TFT screen
Continuously adjusts
angle of TFT screen
Continuously adjusts
front panel tilt angle
Continuously adjusts
front panel tilt angle
Continuously adjusts
angle of TFT screen
Continuously adjusts
angle of TFT screen
Continuously adjusts
angle of TFT screen
Fast forwards the disc
content
Accesses iPod Menu
VOL -
15
Decreases volume
Decreases volume
Decreases volume
Decreases volume
Decreases volume
Decreases volume
Decreases volume
VOL +
16
Increases volume
Increases volume
Increases volume
Increases volume
Increases volume
Increases volume
Increases volume
17
Selects the previous
chapter for playback
Selects the previous
chapter for playback
Searches an available
radio station by decreasing tuning frequency
Selects the previous
track for playback
Searches an available TV
station by decreasing tuning frequency
Searches an available
radio station by decreasing tuning frequency
Pauses playback/starts
playback
18
Pauses playback/starts
playback
Pauses playback/starts
playback
Scans FM/AM radio station; plays/stores radio
station; deletes radio station
Pauses playback/starts
playback
Scans TV station; plays/
stores TV station; deletes
TV station
Scans XM radio station;
plays/stores radio station; deletes radio station
19
Selects the next chapter
for playback
Selects the next chapter
for playback
Searches an available
radio station by increasing tuning frequency
Selects the next track for
playback
Searches an available TV
station by increasing tuning frequency
Searches an available
radio station by increasing tuning frequency
20
Stops playback
Stops playback
Selects FM/AM band
Stops playback
BAND
10
Selects XM, XM1, XM2,
or XM3 band
Selects the next track for
playback
VM9511TS
Table 1: Front Zone Remote Control Functions
Button
Name
GOTO
Function
Ref#
DVD
VCD
TUNER
CD/MP3
TV
XM
iPod
21
Goes to specific time
frame and playback
Goes to specific time
frame and playback
22
Slow playback/slow
rewind playback
Slow playback/slow
rewind playback
ZOOM
23
Zooms in/out on an
image
Zooms in/out on an
image
PIC
24
Displays set-up parameters
Displays set-up parameters
OPEN/
CLOSE
25
Opens/closes the TFT
monitor
Opens/closes the TFT
monitor
Opens/closes the TFT
monitor
Opens/closes the TFT
monitor
Opens/closes the TFT
monitor
Opens/closes the TFT
monitor
Opens/Closes the TFT
monitor
26
Decreases monitor tilt
angle
Decreases monitor tilt
angle
Decreases monitor tilt
angle
Decreases monitor tilt
angle
Decreases monitor tilt
angle
Decreases monitor tilt
angle
Decreases monitor tilt
angle
27
Increases monitor tilt
angle
Increases monitor tilt
angle
Increases monitor tilt
angle
Increases monitor tilt
angle
Increases monitor tilt
angle
Increases monitor tilt
angle
Increases monitor tilt
angle
DISP
28
Selects display mode:
CINEMA, WIDE, NORMAL or Off (Standby)
Selects display mode:
CINEMA, WIDE, NORMAL or Off (Standby)
Selects display mode:
CINEMA, WIDE, NORMAL or Off (Standby)
Selects display mode:
CINEMA, WIDE, NORMAL or Off (Standby)
Selects display mode:
WIDE or OFF
Selects display mode:
WIDE or OFF
Selects display mode:
WIDE or OFF
1, 2, 3, 4, 5,
6, 7, 8, 9, 0
(Numeric
Keypad)
29
Directly accesses chapter
1-6 selects preset for current band
Directly accesses track
1-6 selects preset TV stations
1-6 selects preset for current band
DVD
SETUP
30
Displays DVD Setup
menu
Displays DVD Setup
menu
Displays DVD Setup
menu
Displays DVD Setup
menu
Displays DVD Setup
menu
Displays DVD Setup
menu
Displays DVD Setup
menu
SYS
SETUP
31
Displays System Setup
menu
Displays System Setup
menu
Displays System Setup
menu
Displays System Setup
menu
Displays System Setup
menu
Displays System Setup
menu
Displays System Setup
menu
SEL
32
RDM
33
SCN
34
EJECT
35
Plays all chapters in random order
Plays all tracks in random order
Plays all tracks in random
order
Plays the first ten seconds of each track
Ejects disc
Ejects disc
Ejects disc
Ejects disc
11
Ejects disc
Ejects disc
Ejects disc
VM9511TS
MULTI-ZONE REMOTE CONTROL
Table 2: Multi-Zone Remote Control Functions
Button
Name
Function
Ref #
DVD
VCD
MENU
1
Enters the main menu of the disc
Turns on PBC when playing VCD
TITLE
2
Enters the title menu of the disc
Plays first ten seconds of each chapter/title
Toggles on/off audio output
MUTE
3
Toggles on/off audio output
AUDIO
5
Switches the audio language for disc playback
REPT
7
Setup to repeat playback of each chapter/title/disc
Setup to repeat playback of each chapter/title/disc
R.SRC
8
Selects playing mode for rear zone
Selects playing mode for rear zone
SUBTITLE
GOTO
1, 2, 3, 4, 5,
6, 7, 8, 9, 0
(Numeric
Keypad)
9
Language selection for subtitle
14
Fast forwards the disc content
Fast forwards the disc content
17
Selects the previous track/chapter for playback
Selects the previous track/chapter for playback
18
Pauses playback/Starts playback
Pauses playback/Starts playback
19
Selects the next track/chapter for playback
Selects the next track/chapter for playback
21
Goes to specific time frame and playback
Goes to specific time frame and playback
22
Slow playback/slow rewind playback
Slow playback/slow rewind playback
29
Directly accesses chapter
NOTE: Your remote control may differ slightly
from the one pictured here. The above diagram is
for illustrative purposes only.
12
VM9511TS
USING THE TFT MONITOR
Open/Close TFT Monitor
Aspect Ratio
Open TFT Monitor
Press the DISP button (28) on the remote control or WIDE/
PICTURE button (2) on the monitor to adjust the aspect ratio
as follows:
Press the OPEN button (1) on the front panel or press the
( ) button (25) of the front zone remote control to activate
the mechanism that moves the display panel into the viewing
position.
CINEMA
The entire screen is extended
horizontally to the aspect ratio of 16 to
9. The extension ratio is the same at
any point.
Close TFT Monitor
Press the OPEN button (1) on the front panel or press the
( ) button (25) of the front zone remote control to load the
display panel back into the compartment.
TFT Monitor Auto Open
WIDE
The screen is extended horizontally to
the aspect ratio of 16 to 9. The
extension ratio increases toward the
right and left ends of the screen.
If “TFT Auto Open” is “on” when the unit is turned on, the
monitor automatically moves to the viewing position.
If “TFT Auto Open” is ”off” when the unit is turned on, press
the OPEN button (1) or ( ) button (25) on the front zone
remote control to move the monitor into the viewing position.
NORMAL
The conventional display image has a
4 to 3 ratio of horizontal to vertical,
leaving a blank area on the right and
left sides of the display.
If “TFT Auto Open” is set to ”Manual”, the TFT will not close
when the key is turned off.
Reverse Driving Use
If the rear-view video camera is connected, the unit is on, and
the monitor is stationed inside the main compartment of the
unit, the monitor automatically moves into the viewing
position and switches to CAMERA mode upon reverse
driving. When the reverse driving stops, the monitor returns
to the main storage compartment.
If the monitor is in display mode, the monitor automatically
switches to CAMERA mode upon reverse driving. When the
reverse driving stops, the monitor return to its original input
mode.
Monitor Tilt Angle Adjustment
A known characteristic of LCD panels is the quality of the
display in relationship to the viewing angle. The monitor
angle can be adjusted for optimum viewing using one of the
following methods:
Step by Step Angle Adjustment
Press the ( ) or ( ) button (3, 4) on the monitor frame to
adjust the tilt angle of the screen one step at a time.
Continuous Angle Adjustment
Press and hold the ( ) or ( ) button (3, 4) on the monitor
frame to adjust the tilt angle in a continuous motion.
“COLOR”, “CONTRAST”, and “TINT” you must be in AUX,
CAMERA or TV Tuner mode.
NOTE: The default adjustment is “0” in PAL mode. Tint is
unavailable for adjustment.
Parameter Adjustment Procedure
1. Enter Picture Quality Setting mode:
Press the PIC button (24) on the remote or press and
hold the WIDE/PICTURE button (2) on the monitor
panel.
2. Select Item to Set:
Press the (>>) (<<) buttons (14, 22) on the remote or
press and hold the (/\) or (V) buttons (18, 19) on the
monitor panel.
3. Set Parameters:
Press (|<<) (>>|) buttons (17, 19) on the remote or press
(<) (>) buttons (16, 17) on the monitor panel.
4. Exit Picture Quality Setting Mode:
Press the PIC button (24) on the remote or press and
hold the WIDE/PICTURE button (2) on the monitor
panel.
Parking Brake
Parking Brake Inhibit
OFF
Image Setting
Table 3 shows the video output mode for each playing
source.
Table 3: Video Output Modes
Playing Source
Video Output Modes
AM/FM TUNER
RGB Mode
XM TUNER
RGB Mode
iPod
RGB Mode
DVD
RGB Mode
NAV
RGB Mode
TV
CVBS Mode
AUX IN
CVBS Mode
CAMERA
CVBS Mode
*CVBS – Composite Video Baseband Signal
Adjustable Parameters
While in DVD or TUNER mode, the only parameter that can
be adjusted is brightness (BRIGHT). To access “PICTURE”,
13
When the pink "Parking" wire is connected to the vehicle
brake switch, the front TFT monitor will display video only
when the parking brake sequence is engaged. Before starting
the parking brake sequence, the radio must be on with the
video media disc inserted and playing.
Parking Brake Sequence
There are two situations that can start the Parking Brake
Sequence:
•
•
Parking brake is engaged (on) when the vehicle is started
or the accessory/ignition is turned on. To activate video,
the following sequence of events must be completed:
a. Release parking brake for 2 seconds.
b. Reapply the parking brake for 2 seconds.
c. Video should be displayed on the TFT monitor within 1
~ 2 seconds.
Parking break is disengaged (off) when the vehicle is
started or the accessory/ignition is turned on. To activate
video, the following sequence of events must be
completed:
a. Set parking brake for 2 seconds.
b. Release parking brake for 2 seconds.
c. Reapply parking brake.
VM9511TS
d. Video should be displayed on the TFT monitor within 1
~ 2 seconds.
Monitor Movement Mechanism
If an obstruction occurs in the monitor path, the following
protective measurements can be executed to prevent
damage to the mechanism or monitor:
Table 4: Monitor Protective Measures
Obstruction
Self
Protection
OPEN Button
Pressed
Power
Reconnected
Monitor loading out horizontally
Monitor is automatically
loaded into unit
Monitor fully
extended horizontally
Monitor is automatically
loaded into unit
Monitor loading in horizontally
Unit stops at
obstruction
point
Monitor fully
extended horizontally
Monitor is automatically
loaded into unit
Monitor loading out vertically
Unit stops at
obstruction
point
Monitor swivels back to the
unit
Monitor swivels back to the
unit
Monitor loading in vertically
Unit stops at
obstruction
point
Monitor swivels back to the
unit
Monitor swivels back to the
unit
After the protective procedure is executed, normal operation
is resumed by pressing the OPEN button (1) or disconnecting
and reconnecting the power.
14
VM9511TS
OPERATING INSTRUCTIONS
Power On / Off
Press the /MUTE button (7) to turn the unit on. The buttons on the
front of the unit light up and “WELCOME” appears briefly in the LCD
panel (23), followed by the current mode status. If the TFT screen is
open, only the current mode status is displayed. You can also turn
on the unit by pressing the OPEN button (1) and opening the TFT
screen.
Press and hold the /MUTE button (7) on the front panel or the
POWER button (4) on the remote to power off the unit.The monitor
is drawn back into the main compartment and the LCD screen
displays “BYE BYE”.
Audible Beep Confirmation
An audible beep tone confirms each function selection. The beep
tone cannot be disabled.
Mute
Press the /MUTE button (7) on the front panel or the MUTE button
(3) on the remote to mute the volume from the unit. Press the MUTE
button again to restore the volume. “MUTE” is displayed on the LCD
monitor. Adjusting the volume or using any of the audio setup
features cancels the mute function.
Playing Source Selection
Press the SRC button (15) on the front panel or the SRC
button (8) on the remote to change between available playing
sources in the following order: TUNER, DVD, CD Changer,
AUX IN, CAMERA (rear view video camera) and SD. The
playing mode is displayed on the TFT and LCD screens.
To program a specific volume level, push and hold the VOL/
LO/DX knob (6) while the yellow volume bar is displayed on
the screen. The unit will beep two times to confirm your turnon volume setting.
The Loud function compensates for deficiencies in sound ranges at
low levels. Loudness levels range from 1-4 or “off”. When the Loud
function is on, “LOUD” is displayed on the screen.
Audio Control Menu
Press and hold the VOL/LO/DX knob (6) or stop making
adjustments for a few seconds to exit the audio control menu.
The Audio Control feature allows you to easily adjust your audio
system to meet the acoustical characteristics of your vehicle, which
vary depending on the type of vehicle and its measurements. To get
the best possible sound quality from your new system, be sure to
adjust the settings for the speakers as well. Proper setting of the
Fader and Balance boosts the effects of the cabin equalizer.
Six-Channel Audio Control
NOTE: Before adjusting the volume of any speaker,
please refer to “Surround Sound” on page 26.
Accessing the Audio Control Menu
Press the VOL/LO/DX knob (6) on the front panel once to display
the “AUDIO” menu.
Table 6: 6-Channel Audio Adjustments
Item
Selecting an Audio Feature for Adjustment
Continuously press the VOL/LO/DX knob (6) on the front panel, or
press the (>>)/(<<) buttons (14, 22) on the remote control or the (/\)/
(V) buttons (18, 19) on the joystick to select the audio feature to be
adjusted.
Adjusting an Audio Feature
Rotate the VOL/LO/DX knob (6), press the (|<<)/(>>|) buttons (17,
19) on the remote control, or press the (<)/(>) buttons (16, 17) on the
joystick to adjust the selected feature to the desired setting.
Table 5: Audio Adjustments
Audio Function
EQ
Adjustable Range
User
AUX IN Mode
Flat
An external peripheral device can be connected to this unit
via RCA output and “AUX-IN”.
Jazz
CAMERA Mode
Classical
“CAMERA” mode is only available if the camera is connected and
during reverse driving. To install a rear view video camera, connect
the video input cable to the camera output cable.
Rock
BASS
Volume Adjustment
TREBL
-14 to +14
To increase or decrease the volume level, turn the ROTARY
ENCODER (6) on the front panel or press the VOL+/ VOL- buttons
(15, 16) on remote control. When the volume level reaches “0” or
“40”, a beep sounds, indicating that the adjustment limit has been
reached. The volume ranges from “0” to “40”. The LCD or TFT
screen displays the volume level for 3 seconds.
SUB
-7 to +7
LOUD
0 (off), 1-4
FAD (Fade)
-9 to +9
BAL
-9 to +9
Programmable Turn-On Volume
NOTE: The Bass and Treble levels are only adjustable
when EQ is set to “User” mode.
This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.
Exiting the Audio Control Menu
Pop
Vocal
-14 to +14
15
Adjustable Range
Master Volume
00 to 40
Front Left Channel Volume
-10 to +10
Front Right Channel Volume
-10 to +10
Rear Left Channel Volume
-10 to +10
Rear Right Channel Volume
-10 to +10
Center Channel Volume
-10 to +10
Subwoofer Volume
-10 to +10
Rear Zone
If a monitor is installed in the rear zone and connected to the
rear zone AV output, passengers in the back seat can control
the DVD output using the rear zone remote control. See
“Multi-Zone Remote Control” on page 12 for instructions.
System Reset
To correct a system halt or other illegal
[RESET] Button
operation, use the tip of a pen to press the
RESET button (22) located on the front
bottom-right corner of the unit. After a system reset, the unit restores
all factory default settings.
NOTE: If the unit is reset while a DVD is playing, the DVD
resumes play once the reset is complete.
Line Mute
If the “MUTE” wire is connected, audio output mutes when a
telephone call is received by the car phone or when verbal
navigation is performed.
VM9511TS
SYSTEM SETUP MENU
In “System Setup” mode, “ASP CONFIG” and “GENERAL
SETUP” are available for adjustment. Setup can be
performed by pressing the dedicated button on the remote
control or by touching the top left corner of the TFT screen.
For system settings, press the SYS SETUP button (31) on
the remote control or touch “SETUP” on the screen to enter
the “SETUP” menu. “SYS SETUP” is highlighted in green.
General Setup Menu
Accessing the General Setup Menu
To access the “GENERAL SETUP” Menu, press the direction
buttons on the joystick (16, 17, 18, 19) or remote control (14,
17, 18, 19, 22) to highlight “GENERAL SETUP” in green.
Adjusting a Feature
1. Enter the option field for the feature you want to adjust
by pressing the >/|| button (18) on the remote or by
pressing the ENTER (joystick) button (20) on the unit. A
submenu appears in a second row with the selected
option highlighted in light blue.
2. Select a new value by pressing the >> or << buttons (14,
22) on the remote control or the /\ or V buttons (18, 19)
on the joystick.
3. Confirm your selection by pressing the <<, |<<, or >>|
buttons (14, 17, 19) on the remote control, or the < or >
button (16, 17) on the joystick. The new value is
highlighted in light blue and setup is complete.
Table 7: General Setup Menu Features
DIRECTION BUTTONS
Setting
Radio
Press the >/|| button (18) on the remote control to enter the
“GENERAL SETUP” menu. A menu appears with the option
for the first item, “Radio”, highlighted in light blue.
Options
USA
• AM Frequency Spacing - 9kHz
• AM Frequency Band 522kHz~1620kHz
• FM Frequency Spacing - 50kHz
• FM Frequency Band 87.5MHz~108.0MHz
South
America 1
• AM Frequency Spacing - 10kHz
• AM Frequency Band 530kHz~1720kHz
• FM Frequency Spacing - 100kHz
• FM Frequency Band 87.5MHz~108.0MHz
Arabia
Korea
Press the >> or << buttons (14, 22) on the remote control or
the /\ or V buttons (18, 19) on the joystick to select the feature
to be adjusted.
• AM Frequency Spacing - 10kHz
• AM Frequency Band 530kHz~1720kHz
• FM Frequency Spacing - 200kHz
• FM Frequency Band 87.5MHz~107.9MHz
Europe
South
America 2
Selecting a Feature for Adjustment
Function
• AM Frequency Spacing - 5kHz
• AM Frequency Band 520kHz~1600kHz
• FM Frequency Spacing - 100kHz
• FM Frequency Band 87.5MHz~108.0MHz
• AM Frequency Spacing - 9kHz
• AM Frequency Band 531kHz~1620kHz
• FM Frequency Spacing - 100kHz
• FM Frequency Band 87.5MHz~108.0MHz
• AM Frequency Spacing - 9kHz
• AM Frequency Band 531kHz~1602kHz
• FM Frequency Spacing - 200kHz
• FM Frequency Band 88.1MHz~107.9MHz
16
Table 7: General Setup Menu Features
Setting
Clock Mode
Screen Saver
Options
Function
China
• AM Frequency Spacing - 9kHz
• AM Frequency Band 522kHz~1620kHz
• FM Frequency Spacing - 100kHz
• FM Frequency Band 87.5MHz~108.0MHz
12H
Clock displays 12 hour time using
AM and PM.
24H
Clock displays 24 hour time up to
23:59.
On
Turn screen saver on/off.
Off
Video Format
(Input circuitry autodetects the
video signal
from the
CAMERA
and Aux In
video source.
Video format
does not
affect the TV
tuner - this is
an NTSC TV
tuner only.
Auto
The color signal output is switched
automatically based on the current
video input signal - NTSC or PAL.
NTSC
The color signals are output in the
standard NTSC format.
PAL
The color signals are output in the
standard PAL format.
TFT Auto
Open
On
The TFT panel automatically opens
when the unit is turned on.
Off
You must press the OPEN button
(1) to open the TFT panel.
Manual
When the ignition is turned OFF,
the TFT panel DOES NOT retract if
it was previously out
OSD Language
English
The menus are displayed in English
only.
Clock
(HH:MM)
See “Adjusting the clock” to learn
how to set the clock.
BACK
Return to previous menu.
Adjusting the Clock
1. Access the “Clock” setting under the General Setup
menu.
2. Press the >> or << buttons (14, 22) on the remote
control or the /\ or V buttons (18, 19) on the joystick to
move the cursor to the “Hour” or “Min” position.
3. Press the |<< or >>| buttons (17, 19) on the remote
control or the < or > buttons (16, 17) on the joystick to
adjust the hour or minutes.
4. Press the << button (14) on the remote control to confirm
setup.
VM9511TS
Returning to the System Setup Menu
To return to the System Setup menu, move to “BACK”, then
press the >/|| button (18) on the remote control.
ASP (Audio Sound Processing) Config
Menu
The ASP Config Menu allows you to make fine audio
adjustments.
button (16, 17) on the joystick. The new value is
highlighted in light blue and setup is complete.
Table 8: ASP Config Menu Features
Setting
Bass Center
Freq
Options
60Hz
80Hz
Accessing the ASP Config Menu
100Hz
To access the “ASP CONFIG” Menu from the “SYSTEM
SETUP” menu, press the direction buttons on the joystick
(16, 17, 18, 19) or remote control (14, 17, 18, 19, 22) to
highlight “ASP CONFIG” in green. Press the >/|| button (18)
on the remote control to enter the “ASP CONFIG” menu. A
menu appears with the option for the first item, “Bass Center
Freq”, highlighted in light blue.
130Hz
Function
According to the audio source, select
the Bass Center Frequency to
achieve the best Bass effect.
150Hz
200Hz
Treble Center
Freq
10KHz
12.5KHz
According to the audio source, select
the Treble Center Frequency to
achieve the best Treble effect.
15KHz
17KHz
Sub.W Filter
80Hz
120Hz
160Hz
Sub.W Phase
Selecting a crossover frequency sets
a cut-off frequency of the subwoofer's
LPF (low-pass filter) and the
“SMALL” speakers' HPF (high-pass
filter). The Crossover frequency setting has no effect if the subwoofer is
set to “OFF” and any other speaker is
set to “LARGE”.
0D
Subwoofer output IN phase
180D
Subwoofer output OUT OF phase
NOTE: Depending on your installation, reversing the subwoofer phase
may increase Bass output.
Bass Q-Factor
1.0
1.25
1.5
Adjusting a Feature
1. Enter the option field for the feature you want to adjust
by pressing the >/|| button (18) on the remote or by
pressing the ENTER (joystick) button (20) on the unit. A
submenu appears in a second row with the selected
option highlighted in light blue.
2. Select a new value by pressing the >> or << buttons (14,
22) on the remote control or the /\ or V buttons (18, 19)
on the joystick.
3. Confirm your selection by pressing the <<, |<<, or >>|
buttons (22, 17, 19) on the remote control, or the < or >
When the Bass Center Frequency is
selected, adjusting the Bass Q-Factor alters the sharpness of the Bass
output.
2.0
BACK
Return to previous menu.
Screen Calibration
After entering calibration mode, a crosshair appears in a
corner quadrant of the screen. To begin calibration, press
and hold the crosshair for one second until it moves to the
next quadrant. Continue for each quadrant until the
calibration is completed.
Exiting the System Setup Menu
To exit setup mode and resume normal playback, press the
SYS SETUP button (31) on the remote control or the DISP
button (5) on the front panel.
17
VM9511TS
MULTI-ZONE OPERATION
Independent sources can be played simultaneously on the
VM9511TS. For example, a video game console can be seen
on the front screen while DVD video is available to rear
passengers.
NOTE: If DVD is selected as the front source and SD
Card is selected for the rear source, then both sources
will switch to SD Card. If SD Card is selected as the front
source and DVD is selected for the rear source, then
both sources will switch to the DVD source. Since the
multimedia processor is shared between optical and SD
Card media, one or the other can be selected, but not
both simultaneously.
Table 9: Multi-ZONE Source Options
Front Zone Source
Available Multi-ZONE Sources
TV
DVD/CD, Aux In, TV, Nav
Aux In
DVD/CD, TV, Aux In, Nav
Nav
DVD/CD, SD Card, Aux In, Nav Voice
Prompt
To access the rear zone SOURCE MENU, touch the top right
corner of the screen, near the Multi-ZONE icon.
Selecting a Source for the Front Zone
To access the FRONT ZONE SOURCE MENU, touch the
TFT screen in the top left corner of the screen.
Select the source to be directed to the rear Multi-ZONE RCA
outputs.
NOTE: Optical media and an SD Card cannot be selected
from the Multi-ZONE Source Menu simultaneously.
This menu allows you to select a source for the front zone.
Selecting a Source for the Rear Zone
The Multi-ZONE sources available for selection depends
upon which Front Zone source is selected, as indicated in
Table 9.
Table 9: Multi-ZONE Source Options
Front Zone Source
NOTE: The AM/FM tuner graphics will change to a "blue
screen" background when any optical or SD Card media
is selected from the Multi-ZONE menu. In addition, only
the top left (Front Zone Source Menu) and right (MultiZONE Source Menu) quadrants of the touch screen are
active during this mode of operation.
Available Multi-ZONE Sources
AM/FM Tuner
DVD/CD, SD Card, TV, Aux In, Nav
DVD/CD
DVD/CD, TV, Aux In, Nav
SD Card
DVD/CD, TV, Aux In, Nav
iPod
Aux In, Nav Voice Prompt
XM
Aux In, Nav Voice Prompt
18
VM9511TS
TUNER OPERATION
Tuner TFT Display
Alternate TFT Tuner Display
Using Preset Stations
Default TFT Tuner Display
The VM9511TS offers an alternate display for the AM / FM
tuner interface that is less bright than the default tuner display
and is more appropriate for night driving.
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the screen.
Storing a Station
1. Select a band (if needed), then select a station.
2. Touch and hold an on-screen preset button (6) for three
seconds. The preset number appears at the top of the
screen.
Recalling a Station
1. Select a band (if needed).
2. Touch an on-screen preset button (6) to select the
corresponding stored station.
To activate this feature, open the TFT screen and then press
and hold the DISP button (5) for more than one second. To
deactivate, press and hold the DISP button again.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Current Radio Band Indicator
Radio Frequency Indicator
Clock
Stereo Broadcasting Indicator
Strong Local Signal Broadcasting Indicator: Touch and
hold to activate/deactivate Local function
Preset Radio Stations: Touch to recall preset stations or
touch and hold to store a station
Front Zone Playing Mode
Rear Zone Playing Mode
User Defined Equalizer Level
Loud Setting Indicator
Current Preset Station Indicator
|<<: Touch to seek backward
>>|: Touch to seek forward
<<: Touch to tune backward one step
>>: Touch to tune forward one step
BAND: Touch to change between AM/FM bands
AS: Touch to automatically store stations
Touch this area to return to the MAIN MENU
Switch to Radio Tuner source
Press the SRC button (15) on the front panel or remote
control (8) to switch to the TUNER source.
Select FM/AM Band
Touch the BAND button (16) on the screen, or press the
BAND button on the unit (14) or remote control (20) to
change between the following bands: FM1, FM2, FM3, AM1,
and AM2.
Auto Tuning
Press and hold the >>| button (19) on remote control or
screen, or the > button on the joystick (17) to seek the next
available radio station by increasing the tuning frequency.
Press the button again to stop searching.
Press and hold the |<< button (17) on the remote control or
screen, or the < button on the joystick (16) to seek the next
available radio station by decreasing the tuning frequency.
Press the button again to stop searching.
Manual Tuning
Press the >> or << buttons (14, 22) on the remote control or
screen, or the /\ or V buttons (18, 19) on the joystick to
increase or decrease the tuning frequency one step.
Press and hold the buttons to continuously tune until you
release them.
19
Auto Store (AS)
Automatic Storing of Preset Stations
To select six strong stations and store them in the current
band:
1.
2.
Select a band (if needed).
Touch AS (26) for 2 seconds to activate the Auto Store
function.
The new stations replace stations already stored in that band.
Local Radio Station Seeking (LOC)
When the Local function is on, only radio stations with a
strong radio signal are played. To activate the Local function
in AM/FM tuner mode, press and hold the VOL/LO/DX knob
(6) on the front panel while the yellow volume bar IS NOT
visible. Press VOL/LO/DX again to turn Local off. When the
Local function is active, “LOC” appears on the screen and a
green indicator is illuminated.
VM9511TS
XM RADIO OPERATION
Listeners can subscribe to XM® Radio on the Web by
visiting www.xmradio.com, or by calling (800) 967-2346.
Customers should have their Radio ID ready (see
“Displaying the Identification (ID) Code”). Customers can
receive a limited number of free-to-air channels without
activation.
Accessing XM® Radio Mode
Press the SRC button (15) on the front panel or remote
control (8) to switch to the XM source.
17. MENU: Access the XM Setup Menu
18. Touch this area to return to the MAIN MENU
Channel Guide, press the SUBTITLE button (9) on the
remote control.
Displaying the Identification (ID) Code
Channel Guide Mode
Before you listen to XM® Radio, you must subscribe to the
service using your radio’s identification number. To display
the radio ID, press the < or > buttons (16, 17) on the joystick
or the CH << or CH >> buttons on the touch screen
repeatedly to tune to channel “000”. The screen displays the
8-character XM radio ID under “CHANNEL NAME”.
When Channel Guide mode is selected, “Search Mode” and
“CHANNEL” appear in the top half of the user interface. “XM”
appears in the top right corner and the first six XM channels
are displayed in the boxes in the bottom half of the TFT
screen.
Selecting a Station
Press the < or > buttons (16, 17) on the joystick, the |<< or
>>| buttons (17, 19) on remote control, or the CH << or CH
>> buttons on the touch screen to change to another station.
Preset Mode
To enter preset mode, touch the BAND button on the screen,
or press the BAND button on the unit (14) or remote control
(20) to change between the following bands: XM1, XM2, or
XM3 (indicated in the top right corner of the TFT screen).
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the TFT screen.
Storing a Station
1. Select a band (if needed), then select a station.
2. Touch and hold an on-screen preset button for three
seconds. The preset number appears at the top of the
screen.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
XM channel name
XM channel number
XM band
Time
Song title
Artist name
Song category
Data services information
Current preset channels/on-screen preset buttons
CH <<: Select the previous channel
CH >>: Slect the next channel
CAT /\: Select next channel in current category only
CAT V: Select previous channel in current category only
DIR CH: Press to enter channel directly using keypad on
screen
15. XM CG: Access Channel/Category Guide mode
16. BAND: Change between XM, XM1, XM2 and XM3
bands
Recalling a Station
1. Select a band (if needed).
2. Touch an on-screen preset button to select the
corresponding stored station.
•
•
•
•
•
Channel/Category Guide Mode
There are two search modes to help navigate through
channels and or categories. To access the Channel/Category
Guide mode press, the ZOOM button (23) on the remote
control or the XM CG button on the touch screen.
Channel Guide is the default search mode. To access
Category Guide, press the TITLE button (2) on the remote
control or touch CAT on the touch screen. To return to
20
•
While in Search Mode, to switch between Channel and
Category search modes, press the CH or CAT buttons in
the touch screen.
Press the >> button (14) on the remote control, the /\
button (18) on the joystick, or the > button on the touch
screen to view the next page of stations. Each page
contains six channels to select from.
Press the << button (22) on remote control, the V button
(19) on the joystick, or the < button on the touch screen to
view the previous page of stations. Each page contains six
channels to select from.
Press the on-screen SCAN button to preview each of the
6 channels on screen for 10 seconds.
Press the on-screen
button to return to the Preset
Mode screen.
Press the on-screen MENU button to access the XM
Setup Menu.
To select a channel while in Channel Guide mode, press the
corresponding preset number (1-6) on the unit, remote
control, or touch screen. The channel will begin playing and
the unit will return to the Preset Mode. While in Preset Mode,
press and hold an on-screen preset button (or 1-6 on the unit
or remote control) to store the channel playing.
VM9511TS
unit, remote control, or touch screen. The channel will
begin playing and the unit will return to the Preset Mode.
While in Preset Mode, press and hold an on-screen
preset button (or 1-6 on the unit or remote control) to
store the channel playing.
Category Guide Mode
When Category Mode is selected, “Search Mode” and
“CATEGORY” appear in the top half of the user interface.
Press the TITLE button (2) to return to the Category Mode
main page and select a different category.
Direct Tuning
To enter a station directly, perform the following steps.
•
•
•
•
•
•
While in Search Mode, to switch between Channel and
Category search modes, press the CH or CAT buttons in
the touch screen.
Press the >> button (14) on the remote control, the /\
button (18) on the joystick, or the > button on the touch
screen to view the next six categories.
Press the << button (22) on the remote control, the V
button (19) on the joystick, or the < button on the touch
screen to view the previous six categories.
Press the on-screen SCAN button to preview each
channel in the selected category for 10 seconds.
Press the on-screen
button to return to the Preset
Mode screen.
Press the on-screen MENU button to access the XM
Setup Menu.
1.
Press the GOTO button (21) until the following screen
appears.
2.
Use number keys on the remote control to enter the
desired XM radio station. You must enter a 3 digit
number (for example, 004).
Press the >/|| button (18) on the remote control or the
joystick ENTER button (20) on the unit or just let the
keypad "time out" after 4 seconds and the station will be
entered automatically. Use the on-screen “CLR” button
to correct entry mistakes and “OK” to enter the channel
number.
3.
XM Setup Menu
While in XM radio mode, press the MENU button (1) on the
remote control to view the XM Setup Menu.
To select a station in a specific category, perform the
following steps.
1.
2.
3.
To select a category, press the corresponding preset
number (1-6) on the front of the unit, the remote control,
or the touch screen. Once a category is selected, the
stations in that category will be displayed on the screen.
Press the >> button (14) on the remote control, the /\
button (18) on the joystick, or the > button on the touch
screen to view the next six stations.
Press the << button (22) on remote control, the V button
(19) on the joystick, or the < button on the touch screen
to view the previous six stations in the selected
category.
To select a channel while in Category Guide mode,
press the corresponding preset number (1-6) on the
Press MENU to exit the current submenu or menu and return
to the previous screen.
21
Diagnostic Mode
This feature is reserved for use by service professionals for
troubleshooting.
Parental Control
By default, this feature is unlocked and all channels can be
accessed by anyone listening to the radio. To lock a station,
press the << button (22) on the remote control or V button
(19) on the joystick until "Channel Number" is highlighted
blue. Input the channel number to be locked. Press the <<
button on the remote control or \/ button on the joystick and
select LOCK. Repeat this sequence for each channel to be
locked. Press the >> button on the remote control or /\ button
(18) on the joystick and navigate back up to Password - input
1264 and the small yellow lock will close indicating that the
channel(s) are locked. Press the MENU button (1) twice to
return to the main XM page.
VM9511TS
DVD/VCD VIDEO OPERATION
NOTE: When properly installed, DVD video cannot be
displayed on the main TFT screen unless the parking brake is
applied. If you attempt to play a DVD while the vehicle is
moving, the TFT screen displays “PARKING” with a blue
background. Rear video screens, if applicable, will operate
normally.
Using the Touch-Screen Controls
The touch key areas for DVD playback are outlined below.
NOTE: For VCD play, the repeat function is not available
if PBC is on.
Sectional Repeat Function (A-B)
Use the A-B function to define a specific area of a disc to
repeat.
Opening/Closing the TFT Video Screen
•
Opening the TFT Screen
To open the TFT video screen, press the OPEN button (1).
The unit beeps and then opens.
•
Press the REPT A-B button (6) on the remote control to
set the start point (A) of the repeated section.
Press the REPT A-B button again once you reach the
desired end point (B) of the repeated section. The
selected portion of the DVD will now repeat continuously.
Press the REPT A-B button again to cancel the A-B
section setting and stop repeat play.
Closing the TFT Screen
Press the OPEN button (1) again to close the TFT screen. If
the screen is in the “IN” position, it moves out before closing.
•
Insert/Eject Disc
Random Playback
Upon inserting a DVD disc, DVD mode is entered and disc
play begins.
A – Return to MAIN MENU
B – DISP key: Displays playing information
C – Select previous chapter
NOTE: If Parental Lock (Rating) is activated and the disc
inserted is not authorized, the 4-digit code must be
entered and/or the disc must be authorized (see
“RATING (Parental Lock) Menu” on page 27).
You cannot insert a disc if there is already a disc in the unit or
if the power is off.
NOTE: DVD-R and DVD-RW will not play unless the
recording session is finalized and the DVD is closed.
Ejecting a Disc
Press the button (21) on the unit or remote control (35) to
eject the disc. The unit automatically reverts to Tuner mode.
You may eject a disc with the unit powered off. The unit will
remain off after the disc is ejected.
Reset the Loading Mechanism
If the disc loads abnormally or an abnormal core mechanism
operation occurs, press and hold the button (21) on the
unit or remote control (35) to reset the loading mechanism.
Normal operation resumes.
Accessing DVD Mode
To switch to DVD mode when a disc is already inserted,
press the SRC button (15) on the front panel or remote
control (8) until “DVD” appears at the bottom of the screen.
D – Select next chapter
E – Display the following on-screen controls: Menu, >/||, ,
|<<, >>|, <<, >>.
With a DVD, VCD, or CD playing, press the RDM button (33)
on the remote control to activate random playback and play
all chapters/tracks in random order. “On” appears on the
screen.
Press the >>| button (19) on the remote control or the >
button on the joystick (17) to play the next random track.
Press the RDM button again to turn random play off.
Controlling Playback
NOTE: When a VCD is playing with PBC turned “On”,
activating random playback automatically turns PBC off.
Stopping Playback
Touch the stop button ( ) on the screen or press the /
BAND button (20) on the remote control to stop DVD play.
Pausing Playback
Touch the play/pause button (>/||) on the screen or press the
>/|| button on the remote control (18) to suspend or resume
disc play.
Slow Motion Playback
Accessing the DVD Menu
Press the MENU button (1) on the remote control to recall the
main DVD menu. Use the directional (arrow) buttons (<, >, /\
& V) on the joystick (16, 17, 18, 19) to select a title from the
menu.
Press the TITLE button (2) on the remote control to select a
different title for playback.
Press the << button (22) on the remote control or the V button
(19) on the joystick to play the current title in slow motion at 1/
2, 1/4, 1/6 or 1/7, the normal speed. Press >/|| (18) to resume
normal play. Continue pressing the << or V button to slow
reverse.
Press the >/|| button (18) on the remote control or the ENTER
(joystick) button (20) to confirm your selection and begin
playback.
Repeat Playback
Moving Through Chapters
Press the REPT button (7) on the remote control to alter
repeat mode according to the following:
Press the >>| button (19) on the remote control or the >
button on the joystick (17) to advance to the next chapter on
the DVD.
•
•
•
DVD: Repeat Title, Repeat Chapter, Repeat Off
VCD (PBC Off): Repeat Single, Repeat Off
MP3: Repeat Single, Repeat Folder, Repeat Off
22
Press the |<< button (17) on the remote control or the <
button on the joystick (16) to move to the previous chapter.
VM9511TS
Fast Forward/Fast Reverse
•
Press the >> button (14) on the remote control or the /\ button
(18) on the joystick to fast forward. Keep pressing and
releasing the button to increase the rate from “2X” to “4X”,
“8X”, and “20X”. Continue pressing the >> or /\ button to fast
reverse.
For DVD mode, you can choose Time or Title/Chapter
search.
DVD Search
Time – Go to specific
time in current title
Title/Chapter – Go to
specific time in a
chapter
Scanning
Press the SCN button (34) on the remote control to play the
first ten seconds of each chapter. Press SCN again to stop
the scan function and play the current chapter.
•
Selecting 2-Channel and 6-Channel Audio
Playback
For VCD mode, press the GOTO button to choose
between Track Search, Disc Search and Exit.
VCD Track Search
2-Channel Audio (Down Mix) Support for CD, SD Card
and DVD
Time – Go to specific
time in the current track
Linear pulse code modulation (LPCM) and pulse code
modulation (PCM) support is available for CD, SD Card and
DVD discs when 2-channel audio is selected.
Track – Go to specific
track
6- Channel Audio Support for CD, SD Card and DVD
Time – Go to specific
time on disc
VCD Disc Search
Pro-Logic II is available for decoding analog or digital 2channel down mixed sources. Dolby Digital is available for
decoding digital bit-stream sources.
Track – Go to specific
track
NOTE: 2-channel audio support is available for AM/FM
tuner, TV tuner, Aux Input, XM, iPod and Navigation only.
6-channel audio support is available for DVD/CD/CD-R
and SD card.
3.
Table 10: Speaker Output Options
5.
Speaker Setup
Front
Spkr
Rear
Spkr
2CH mode
X
X
Play 2-channel (down
mix) audio in 6-channel mode with ProLogic II "ON"
X
X
Play 6-channel audio
in 6-channel mode
with Dolby Digital
"ON"
X
X
Center
Spkr
SubWoofer
X
X
X
X
Goto Search
During DVD or VCD playback, perform the following steps to
use the GOTO feature to access a specific location on a disc:
1.
2.
Press the GOTO button (21) on remote control to enter
“GO TO” mode.
Press the >> or << buttons (14, 22) on the remote
control or the < or > buttons (16, 17) on the joystick to
select a category (highlighted in blue).
4.
Enter a time into the field using the numeric keypad (29)
on the remote control.
Press the >/|| button (18) on the remote control or the
ENTER (joystick) button (20) to go to the specified
location on the disc.
Press the GOTO button again to exit.
Direct Chapter / Track Selection
During DVD, VCD and CD
playback, you can use the numeric
keypad on the remote control (29)
to access a track directly.
Viewing an Alternate
Picture Angle (DVD
Only)
Some DVDs contain scenes that have been shot
simultaneously from different angles. For discs recorded with
multiple angles, press the ANGLE button (13) on the remote
control to toggle available angles of the on-screen image.
Multi-Language Discs (DVD Only)
Changing Audio Language
If you are watching a disc recorded in multiple languages,
press the AUDIO button (5) on the remote control to choose
a language.
Changing Subtitle Language
If you are watching a disc recorded in multiple languages with
subtitles, press the SUBTITLE button (9) on the remote
control to choose the language in which you would like the
subtitles to appear.
NOTE: During VCD playback, press the AUDIO button (5)
on the remote control to choose between Left Channel,
Right Channel, and Stereo.
PBC (Play Back Control - VCD Only)
For VCDs with play back functionality, play back control
(PBC) provides additional controls for VCD playback.
Press the MENU button (1) on the remote control to toggle
the PBC function “On”/”Off”. Once PBC is on, playback starts
from track one of the play list.
NOTE: When PBC is activated, fast forward, slow
playback, and previous/next track are available. Repeat
and direct track selection are not available.
When PBC is activated, selecting random, scan, or search
playback automatically deactivates PBC.
Playback Information
During DVD and VCD playback, press the INFO button (10)
on the remote control to display playback information on the
screen, including the media playing and current playback
time.
DVD Playback Information
The following information is displayed at the bottom of the
screen during DVD playback:
•
Zooming
Press the ZOOM button (23) on the remote control to enlarge
and pan through the video image using the following options:
“Q1”, “Q2”, “Q3”, and “OFF”.
23
•
T : 5/8 – “5 / 8" indicates the fifth of 8 titles on the DVD is
currently playing.
• C : 2/16 – “2 / 16" indicates that the second of 16 titles
on the DVD is currently playing.
00:41:28 – “00:41:28” indicates the playback time of the
current title.
VM9511TS
•
2 / 6 Eng – The language display information indicates
the second language out of 6 (English) is currently being
used.
The following information appears at the bottom of the screen
during DVD playback:
Front: DVD/CD Rear: AUXIN
•
•
Dolby Digital
Bypass
Front: DVD is the current playback source for the front
zone.
Rear: AUX IN is the current playback source for the rear
zone.
"Dolby Digital" is the selected playback audio encoding
process.
Bypass indicates that the ASP (Audio Signal Processor) is
being bypassed when Dolby Digital decoding is active.
VCD Playback Information
•
•
EQ: FLAT – The equalizer setting is FLAT.
Loud: Level 1 – The Loud option is set to Level 1
loudness.
General Disc Information
Table 11: Disc Properties
Symbo
l
12cm Disc Properties
Max Play
Time
Single side single layer (DVD-5)
Single side double layer (DVD-9)
Double side single layer (DVD-10)
Double side double layer (DVD-18)
(MPEG 2
Method)
133 minutes
242 minutes
266 minutes
484 minutes
Single side single layer (VCD)
(MPEG 1
Method)
74 minutes
Single side single layer
74 minutes
The following information is displayed on the screen during
VCD playback:
Table 12: Disc Symbols
Symbol
•
•
•
VCD2.0 – Format of current disc.
T: 6/18 – “6/18” indicates the sixth of 18 tracks on the VCD
is currently playing.
00:02:18 – “00:02:18” indicates the playback time of the
current track.
The following information appears on the screen during VCD
playback in 6-Channel mode:
Front: DVD
•
•
Rear: AUXIN
MPEG
MOVIE
Front: DVD – “DVD” is the current playing source for the
front zone.
Rear: AUX IN – “AUX IN” is the current playing source for
the rear zone.
“MPEG” is the decoding method in use.
"Movie" indicates that movie effects are being applied to
the audio sound track from the VCD.
The following information appears on the screen during VCD
playback in 2-Channel mode:
•
•
Front: DVD – “DVD” is the current playing source for the
front zone.
Rear: AUX IN – “AUX IN” is the current playing source for
the rear zone.
Meaning
Number of voice languages recorded. The number inside the icon indicates the number languages on the disc (maximum of 8).
Number of subtitle languages available on the
disc (maximum of 32).
Number of angles provided (maximum of 9).
Aspect ratios available. “LB” stands for Letter Box
and “PS” stands for Pan/Scan. In the example on
the left, the 16:9 video can be converted to Letter
Box video.
Indicates the region code where the disc can be
played.
• Region 1: USA, Canada, East Pacific Ocean
Islands
• Region 2: Japan, Western Europe, Northern
Europe, Egypt, South Africa, Middle East
• Region 3: Taiwan, Hong Kong, South Korea,
Thailand, Indonesia, South-East Asia
• Region 4: Australia, New Zealand, Middle and
South America, South Pacific Ocean Islands/
Oceania
• Region 5: Russia, Mongolia, India, Middle
Asia, Eastern Europe, North Korea, North
Africa, North-West Asia
• Region 6: Mainland China
• ALL: All regions
24
VM9511TS
DVD/DISC SETUP MENU
NOTE: A DVD/disc must be loaded into the mechanism
and playing prior to accessing the DVD Setup menu.
While the DVD/disc is playing, press the DVD SETUP
button (30) on the remote to access the DVD Setup
menu.
can also touch the on-screen menu selection to access that
menu.
DIRECTION BUTTONS
In “DVD Setup” mode, “LANGUAGE”, “VIDEO”, “AUDIO”
“SPK CONFIG”, “PRO-LOGIC II”, and “RATING” (parental
lock) are available for setup. These operations can be
performed using the remote control or joystick controls.
Function
Select the default language in which
you would like audio (when optional) to
be played.
DVD Menu
English
Select the default language in which
you would like the DVD menu (if applicable) to be displayed.
Return to previous menu.
Table 14: VIDEO Menu Features
Selecting a Feature for Adjustment
For system settings, press the DVD SETUP button (30) on
the remote control or touch “SETUP” on the screen to enter
the “SETUP” menu. “SYS SETUP” is highlighted in green.
Once inside a menu, press the >> or << buttons (14, 22) on
the remote control or the /\ or V buttons (18, 19) on the
joystick to select the feature to be adjusted.
To access the “DVD SETUP” Menu, press the V button (7) on
the remote control to choose the “DVD SETUP” option, then
press the >/|| button (18), or just touch “DVD SETUP” on the
screen. “LANGUAGE” is highlighted in green.
Adjusting a Feature
1. Enter the option field for the feature you want to adjust
by pressing the >/|| button (18) on the remote or by
pressing the ENTER (joystick) button (20) on the unit. A
submenu appears in a second row with the selected
option highlighted in light blue.
2. Select a new value by pressing the >> or << buttons (14,
22) on the remote control or the /\ or V buttons (18, 19)
on the joystick.
3. Confirm your selection by pressing the <<, |<<, or >>|
buttons (22, 17, 19) on the remote control, or the < or >
button (16, 17) on the joystick. The new value is
highlighted in light blue and setup is complete.
Setting
LANGUAGE Menu
If a DVD supports more than 1 Subtitle or Audio language, all
the languages are available for selection during playback. If
the selected language is not supported by the DVD, then the
default language is used. During playback, press the
SUBTITLE (9) or AUDIO (5) button on the remote control to
change the language directly. This will not affect the DVD
menu settings.
To access a menu (LANGUAGE, VIDEO, AUDIO, SPK
CONFIG, PRO-LOGIC II, or RATING), press the direction
buttons on the joystick (16, 17, 18, 19) or remote control (14,
17, 18, 19, 22) to highlight the desired menu in green. You
Options
English
VIDEO Menu
Setup can be performed by pressing the dedicated button on
the remote control, or by pressing the SRC button (15) on the
front panel.
Accessing a Menu
Setting
Audio
BACK
Accessing the DVD Setup Screen
NOTE: Once the DVD setup is complete, the settings are
memorized. To return to the factory default settings,
press the RESET button (25) on the front panel.
Table 13: LANGUAGE Menu Features
Table 13: LANGUAGE Menu Features
Setting
Subtitle
Options
English
Auto
Function
Select the default language in which
you would like subtitles (if applicable) to
be displayed.
Off
25
TV Shape
(Aspect
Ratio)
Options
Function
4:3 PS
With 16:9 display, the left and right sides
are cut off.
4:3 LB
With 16:9 display, the top and bottom are
cut off.
16:9
Image is presented in wide view with a
16:9 aspect ratio.
Angle
Mark
On
Angle indicator (if applicable) is shown.
Off
Angle indicator is not shown.
View Mode
Fill
Original
H Fit
W Fit
Fit to
Scrn
Pan Scan
BACK
Return to previous menu.
NOTE: For standard discs not formatted for
“widescreen”, use of the 16:9 aspect ratio will result in
image distortion.
VM9511TS
AUDIO Menu
SPK CONFIG Menu
Table 16: SPK CONFIG Menu Features
The VM9511TS has a built-in Pink Noise generator to help
set the relative speaker levels for multi-channel audio
playback.
Setting
LR (Left Rear) /
RR (Right Rear)
Table 15: AUDIO Menu Features
Setting
Pink
Noise
DRC
Options
Off
Stop output of pink noise
Left
Left channel pink noise
Center
Center channel pink noise
Right
Right channel pink noise
Left Surr
Left surround channel pink noise
Right Surr
Right surround channel pink noise
Subwoofer
Subwoofer pink noise
Off
Employ the Dynamic Range Control for
better playback for low volumes.
On
CNTR
CTRL
Function
5ms
4ms
3ms
Adjust the time difference between the
center and front speakers to create a
time delay between 1 and 5 milliseconds, producing a more accurate audio
effect.
2ms
1ms
0ms
REAR
CTRL
15ms
12ms
9ms
3ms
0ms
BACK
CTR (Center)
To change speaker settings for 2-channel mode, use the >>
or << buttons (14, 22) on the remote control or the /\ or V
buttons (18, 19) on the joystick to select “DownMix”. To
change speaker settings for 6-channel mode, select “Full
6CH”. After selecting 2 or 6-channel mode, use the >>|
button (19) on remote control or the > button on the joystick
(17) to move to the speaker settings on the right.
Speaker Selection
Adjust the time difference between the
rear and front speakers to create a
time delay between 3 and 15 milliseconds, producing a more accurate audio
effect.
6ms
Down
Sampling
SUB (Subwoofer)
Selecting LARGE for the multi-channel speaker option will
give a full range output. Selecting SMALL for the multichannel speaker option will activate a high pass filter whose
crossover is dependent upon the sub-woofer low pass filter
frequency. For example, if the subwoofer low pass filter is set
to 80Hz, then the high pass SMALL speaker crossover will be
set to 90Hz.
Off
Normal Output
Low pass
on
Audio signal output at 48kHz
80Hz
90Hz
Return to previous menu.
120Hz
135Hz
160Hz
180Hz
NOTE: When Down Sampling is ON, the audio output
signal will be converted to 48kHz. When Down Sampling
is OFF, the original sampling frequency is preserved.
High pass
Refer to Table 16 when selecting speaker options for each
mode.
Table 16: SPK CONFIG Menu Features
Setting
FL (Front Left) /
FR (Front Right)
Options
Function
Large
Use when front speakers have
good bass output.
Small
Use when speakers do not have
good bass output.
26
Options
Function
Large
Use when rear speakers have
good bass output.
Small
Use when rear speakers do not
have good bass output.
None
Use when rear speakers are not
present.
Present
Use when subwoofer is present.
None
Use when subwoofer is not
present.
Large
Use when center speaker has
good bass output.
Small
Use when center speaker does
not have good bass output.
None
Use when center speaker is not
present.
BACK
Return to previous menu.
Surround Sound
Dolby Digital
Dolby Digital is the reigning standard for surround sound
technology in general and 5.1-channel surround sound in
particular.
Dolby Digital is a highly sophisticated and versatile audio
encoding/decoding technology. Dolby Digital technology can
transmit mono, stereo (two-channel), or up to 5.1-channel
surround sound.
Pro-Logic II
Pro-Logic II is a dramatically improved matrix surround
system based on the original Dolby Pro Logic system. ProLogic II offers two full-range stereo surround channels, more
sophisticated steering logic, high channel separation and an
exceptionally stable sound field. Dolby Pro-Logic II uses
simple servo circuits used to derive the five audio channels.
Unlike other "Surround Effects" found in other consumer
equipment, Dolby Pro-Logic II does not introduce unwanted
delays, echoes, reverberations or tonal colorations.
VM9511TS
Table 17: Pro-Logic II Menu Features
Setting
Options
Decode Mode
Function
Table 18: RATING Menu Features
Setting
Off
Play original audio format.
Pro-Logic
II
Use Pro-Logic II decoding
method.
Pro-Logic
II Matrix
Play mono output with surround
effect.
4. PG-13
Pro-Logic
II Movie
Enhance movie surround effects.
5. PG-R
Pro-Logic
II Music
Play surround music effects.
Panorama
(Only available
when Pro-Logic II
Music Mode is
selected.)
On
Extends the audio from front to
rear to achieve a better audio surround effect.
Off
Panorama is turned off.
Dimension Ctrl
(Only available
when Pro-Logic II
Music Mode is
selected.)
0-6
Adjusts the distribution of the front
and rear audio for a better audio
surround effect.
Center Width Ctrl
(Only available
when Pro-Logic II
Music Mode is
selected.)
0-6
BACK
Rating
Options
1. Kid Safe
2. G
3. PG
Function
Select the appropriate rating level
for the intended audience.
You may override higher ratings
by using your password.
6. R
Adjusts the width of the center
surround effect.
Return to previous menu.
NOTE: Pro-Logic II is recommended when the playback
source is LPCM (Linear Pulse Code Modulation) or 2channel down mixed digital bit-stream.
7. NC-17
8. Adult
Load Factory
BACK
Reset
Select “Reset” to restore the factory default settings for the Rating
system only.
Return to previous menu.
To reset the password, access the “RATING” menu and enter
the current password. Once the correct password is entered,
you can access the “Password” field and enter a new one.
NOTE: Record the password and keep it in a safe place
for future reference. The rating for each disc is marked
on the disc, disc packing, or documentation. If the rating
is not available on the disc, the parental lock feature is
unavailable. Some discs restrict only portions of the disc
and the appropriate content will play. For details, please
refer to the disc description.
NOTE: When Pro-Logic II Music mode is selected,
Dimension Control and Center Width are available for
fine tuning to achieve a more realistic surround sound
processing.
RATING (Parental Lock) Menu
The DVD system has a built-in parental lock feature to
prevent unauthorized persons from viewing restricted disc
content. By default, the rating system is unlocked. Once
setup, the parental lock is released only by entering the
correct password. Once the password is entered, rating is
available for setup.
Table 18: RATING Menu Features
Setting
Password
Options
____
Function
Enter a 4-digit password to activate the “Rating” feature.
27
VM9511TS
DVD/DISC AUDIO OPERATION
Instructions for TFT control and Insert/Eject are the same for
DVD, CD and MP3 operation. Please see the DVD/Disc
Video Operation section for information about these topics.
The VM9511TS will play music or other audio files from the
following disc media:
•
•
•
•
CD-DA
CD-R/RW with MP3 or WMA files
DVD
DVD-R/RW with MP3 or WMA files
13.
14.
15.
16.
17.
18.
19.
>>|: Touch to move to next track
<<: Touch to rewind current track
>>: Touch to fast forward current track
Front Zone Playing Mode
Rear Zone Playing Mode
Encoding method of media being played
"Surround Music" effect selected
Controlling Playback
Stopping Playback
Upon inserting a disc with the TFT screen open, the disc and
track title (if available), along with the track number and
playing time appear on the screen.
Press the 6/STOP button (13) on the front panel or the /
BAND button (20) on the remote control to stop disc play.
CD Player User Interface
To resume playback, press the ENTER button, or the joystick
(20), on the front panel or the >/|| button on the remote
control (18).
The on-screen indicators and touch key areas for CD
playback are outlined below.
Pausing Playback
Press the ENTER button, or the joystick (20), on the front
panel or the >/|| button on the remote control (18) to suspend
or resume disc play.
Moving Through Tracks
Press the >>| button (19) on the remote control or the >
button on the joystick (17) to advance to the next track on the
disc.
Press the |<< button (17) on the remote control or the <
button on the joystick (16) to move to the previous track.
Repeat Playback
Press the 4/RPT button (11) on front panel or the REPT
button (7) on remote control to alter repeat mode according to
the following:
•
•
•
•
DVD: Repeat Title, Repeat Chapter, Repeat Off
CD-DA: Repeat Single, Repeat Off
CD-R/RW: Repeat Single, Repeat Off
DVD-R/RW: Repeat Single, Repeat Off
Track Scan Select (CD-DA discs only)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Current track and total number of tracks on disc
Elapsed playing time
Touch to activate/deactivate Repeat play mode
Touch to activate/deactivate Scan mode
Touch to activate/deactivate Random mode
Current time
Disc Title
Track Title
Touch to return to MAIN MENU
>/||: Touch to play/pause disc playback
: Touch to stop disc playback
|<<: Touch to move to previous track
During disc play, press the 3/SCN button (10) on the unit or
the SCN button (34) on the remote control to play the first 10
seconds of each track. When a desired track is reached,
press the SCN button again to cancel the function and play
the selected track.
Random Play Select
During disc play, press the 5/RDM button (12) to play the
tracks on the disc in a random, shuffled order. In Random
Play mode, you can Press the |<< or >>| button (17, 19) on
remote control or the < or > button (16, 17) on the joystick to
select a track in random order instead of the normal
28
progression. Press 5/RDM again to cancel Random Play
mode.
NOTE: CD-R and CD-RW will not play unless the
recording session is closed.
Fast Forward
Press the >> button (14) on the remote control or the /\ button
(18) on the joystick to fast forward. Keep pressing and
releasing the button to increase the rate from “2X” to “4X”,
“8X”, and “20X”.
MP3/WMA Operation
This player allows you to play back MP3 and WMA files
recorded onto CD-R/RW's and DVD-R/RW’s. For CD-RW
discs, please make sure it is formatted using the full method
and not the quick method to prevent illegal disc operation.
Up to 999 songs/files can be burned onto a disc for a MEGA
DVD music mix. Do not exceed this number of songs/files or
disc readability problems may occur.
MP3 Format Compatibility
The file naming formats listed below are compatible with this
unit:
•
•
•
ISO 9660 – file name: 12 characters, file extension: 3
characters
ISO 9660 – file name: 31 characters, file extension: 3
characters
Joliet – 64 characters
If the file or folder name does not conform to ISO 9660 file
system standards, it may not be displayed or played back
correctly.
Use the following settings when compressing audio data for
your MP3 disc:
•
•
Transfer Bit Rate: 128kbps
Sampling Frequency: 48kHz
When recording MP3 up to the maximum disc capacity,
disable additional writing. For recording on an empty disc up
to maximum disc capacity, use the "Disc at once" setting.
Playing MP3/WMA Files
After inserting a MP3/WMA disc, files will play in the
sequence of the “Root’ directory.
Use the numeric keypad (29) on the remote control to access
files directly.
VM9511TS
NOTE: When burning MP3 / WMA files onto a DVD disc,
use the 2X or 4X burning option, if available. This slower
burning speed will help eliminate buffer errors and
increase disc reading reliability. Also, use folders when
burning large numbers of songs / files to a disc for easy
music navigation. Select the "Disc at Once" option and
close your disc.
29
VM9511TS
SD CARD READER OPERATION
Accessing SD Card Mode
Moving Through Chapters
To switch to SD card mode, press the SRC button (15) on the
front panel.
Press the >>| button (19) on the remote control or the >
button on the joystick (17) to advance to the next chapter.
Using the Touch-Screen Controls
Press the |<< button (17) on the remote control or the <
button on the joystick (16) to move to the previous chapter.
The touch keys for SD card playback are described below.
Change Directory
Touch the ( [DIR+] / [DIR-] ) key on the screen to navigate
through the Directories/Folders
Previous/Next Page
Touch the ( [PAGE+] / [PAGE-] ) key on the screen to
navigate through Pages/Files.
Direct Chapter / Track Selection
During DVD, VCD and CD
playback, you can use the numeric
keypad on the remote control (29)
to access a track directly.
•
•
•
•
•
•
>/||: Play/Pause playback
: Stop playback
PAGE -: View previous page
PAGE +: View next page
DIR -: View previous directory
DIR +: View next directory
NOTE: Media (SD Card/CD-R/DVD) with a ROOT directory
containing only music, movie or JPEG files may cause
the RANDOM / REPEAT function to work incorrectly. To
ensure the proper playback of music, movie, and JPEG
files, place all media files inside folders on the data
storage media.
Controlling Playback
Stopping Playback
Touch the stop button ( ) on the screen or press the /
BAND button (20) on the remote control to stop playback.
Pausing Playback
Touch the play/pause button (>/||) on the screen, press the >/
|| button (18) on the remote control, or press the joystick
button (20) on the front panel to suspend or resume
playback.
Repeat Playback
Press the REPT button (7) on the remote control or touch
“Repeat” on the screen to alter repeat mode according to the
following: Repeat Single, Repeat Folder, Repeat Off.
Random Playback
Press the RDM button (33) on the remote control or touch
“Random” on the screen to activate random playback and
play all tracks in random order.
30
VM9511TS
IPOD OPERATION
Accessing iPod Mode
The unit will automatically switch to iPod mode when an iPod
is plugged into the media module. To return to the iPod menu
from any other source menu, press the SRC button (15) on
the front panel or remote control (8) until the iPod menu
appears on the screen.
Press the AUDIO button (5) on the remote control to access
the iPod VIDEO mode. The VM9511TS will release control
back to the iPod so you can select video media to be
displayed on the VM9511TS TFT monitor. To exit VIDEO
mode, press the >> button (14) on the remote control or
MENU button on the iPod.
NOTE: To transmit the video from your iPod to the
VM9511TS screen, you must set the following options
through the iPod video settings menu: TV Out = On, TV
Signal = NTSC, and Widescreen = On.
Photo Playback
While iPod photos can be viewed on the VM9511TS screen,
you must use the iPod to control photo playback options.
Press the MENU button (1) on the remote control to access
the iPod PHOTO mode. The VM9511TS will release control
back to the iPod so you can select video media to be
displayed on the VM9511TS TFT monitor. To exit PHOTO
mode, press the >> button (14) on the remote control or
MENU button on the iPod.
Controlling your iPod
The following remote control buttons are used to access the
iPod menus:
NOTE: After disconnecting your iPod, the VM9511TS will
always return to last mode accessed when your iPod is
plugged back into the unit.
TITLE = Music
Fast Forward/Fast Reverse
MENU = Photos
Press and hold the |<< or >>| buttons (17, 19) for 1 second
and continue to hold for fast forward or fast reverse. Release
to resume normal play.
AUDIO = Videos
Use the joystick on the unit or the directional keys on the
remote control to navigate the iPod menus.
Music Playback
Press the >>| button (19) on remote control, or the > button
on the joystick (17) to move to the next item on the menu.
Press the |<< button (17) on the remote control, or the <
button on the joystick (16) to move to the previous item on the
menu.
Press the >/|| button (18) on the remote control or the joystick
ENTER button (20) on the head unit to select the highlighted
menu option.
Search Playlist/Artist/Album/Song
To search through Playlists, Artists, Albums and Songs,
press the 1 button (29) on the remote control keypad while in
one of the following directories: Playlist, Artist, Album or
Song. The selected directory will be accessed with the
number of pages and files in that directory displayed at the
top of the page. To access the page or file, enter the page or
file number directly from the remote control keypad. Press
the |<< or >>| button (17, 19) on the remote control or the < or
> button (16, 17) on the joystick to select the desired song or
track.
Press the >> button (14) on the remote control or the /\ button
(18) on the joystick to return to the previous menu.
Video Playback
While iPod video can be viewed on the VM9511TS screen,
you must use the iPod to control video playback options.
31
VM9511TS
TV TUNER OPERATION
Accessing TV Mode
To switch to TV mode, press the SRC button (15) on the front
panel or on the remote control (8) until “TV” appears at the
bottom of the screen.
Seek Tuning
Press the >>| button (19) on remote control, or the > button
on the joystick (17) to seek the next available TV station by
increasing the tuning frequency.
Press the |<< button (17) on the remote control, or the <
button on the joystick (16) to seek the next available TV
station by decreasing the tuning frequency.
Once a TV station is searched, the auto seeking stops and
the TV station is played. If no station is searched, the tuning
stops at the first channel after performing a round search.
Storing Stations (AS)
Auto Memory Tuning
To select the strong stations in the current TV frequency
range, press and hold the joystick button (20) to activate the
Auto-Store function. The new stations replace stations
already stored. Press the joystick button again or press the
/BAND button (18) on the remote control to stop searching.
Selecting a TV Station
To browse through stored stations:
•
•
Press the >> button (14) on the remote control or the /\
button (18) on the joystick to tune to the next stored
station.
Press the << button (22) on remote control or the V button
(19) on the joystick to tune to the previous stored station.
Direct Channel Selection
Use the numeric keypad on the
remote control (29) to enter a
specific TV station.
Display Current Channel
Press the INFO button (10) on the
remote control to display
information regarding the current
TV station.
32
VM9511TS
NAVIGATION SYSTEM
The VM9511TS is "navigation ready." Before accessing any
navigation features, you must purchase and install the
NAV100 module. All installation and operating instructions
will be included with the NAV100 navigation module.
Once the NAV100 is connected and operating properly, the
NAVI source mode will become active. While the NAV100 is
not installed, the NAVI option appears gray, indicating the
function is not available.
33
VM9511TS
TROUBLESHOOTING
Table 19: Troubleshooting
Problem
Cause
Corrective Action
GENERAL
Unit will not power on
Remote control does not function
No/low audio output
Poor sound quality or distortion
Radio Fuse blown
Install new fuse with correct rating
Car battery fuse blown
Install new fuse with correct rating
Illegal operation
Press the RESET button located in the bottom right corner of the front panel
Battery depleted
Replace battery with new one
Battery installed incorrectly
Remove battery and install correctly
Improper audio output connection
Check wiring and correct
Volume set too low
Increase volume level
Improper “MUTE” connection
Review wiring diagram and check “MUTE” connection
Speakers damaged
Replace speakers
Heavily biased volume balance
Adjust the channel balance to the center position
Speaker wiring is in contact with metal part of car
Insulate all speaker wiring connections
Pirated disc is in use
Use original copy
Speaker power rating not compatible with unit
Connect proper speakers
Speaker is shorted
Check speaker contact
Tel-Mute malfunction
“MUTE” wire is grounded
Check that “MUTE” connection is not grounded and that it’s properly insulated
Unit resets itself when engine is off
Incorrect connection between ACC and positive battery
wire
Check wiring and correct
TFT MONITOR
Monitor does not open automatically
TFT Auto Open is turned off
Turn TFT Auto Open on
No image
Incorrect connection to parking brake wire
Check wiring and correct
PRK SW is activated and parking brake is not engaged
Stop vehicle in safe place and apply parking brake
Flashing image or interference appears on screen
DVD is not compatible with current TV system settings
Change setup to accommodate disc
Improper video signal connections
Check wiring and correct
Prolonged image or improper height/width ratio display
Improper aspect ratio setup
Use correct aspect ratio setting
Monitor stops at incorrect position
Moving path is blocked
Press OPEN key to restart monitor movement
TUNER
Weak station searching
Cannot insert disc
Auto antenna is not fully extended
Connect the auto antenna control cable properly
Auto antenna not properly connected
Connect the auto antenna control cable properly
LOCAL function is activated
Turn LOCAL function off
Disc already inside unit
Eject current disc and insert new one
34
VM9511TS
Table 19: Troubleshooting
Problem
Disc does not play back
Cause
Corrective Action
Disc is warped or scratched
Use disc in good condition
Disc is dirty or wet
Clean disc with soft cloth
Laser pickup is dirty
Clean laser pickup with cleaning disc
Incompatible disc is used
Use compatible disc
Disc rating exceeds Parental Lock rating limit
Change Parental Lock settings to lower restriction
Disc region code is not compatible with unit
Use disc with proper region code
Disc is inserted upside down
Insert disc with label side up
Image blurred, distorted, or dark
Disc is illegally copied
Use original disc
PBC cannot be used during VCD playback
PCB is not available on the disc
No repeat or searching while playing VCD
PCB is on
Turn PCB off
Disc is dirty or scratched
Clean disc or replace
File is damaged/bad recording
Recreate disc with good files
MP3
Interruption occurred during playback
Incorrect playback message displayed
Message is longer than LCD can display
XM RADIO
No Sound
Incorrect cable connections
XM source not available
Incorrect cable connections
Check RCA cables
Check XM Data cable or Media Module Cable
“ANTENNA” appears on the XM main screen
Antenna not connected
Check satellite antenna connection
All other Errors
Reset Media Module
IPOD
iPod source not available
Incorrect cable connections
Check jLink and Media Module cables
Cannot see video and photo media on TFT screen
Wrong iPod Video Settings
Change iPod video settings to TV Out = On
Check Media Module yellow RCA video input cable
All other errors
Reset Media Module
Error Messages
Table 20: Error Messages
Message Displayed
Cause
Loading
Disc is being read
No Disc
Disc is dirty
Bad Disc
Unknown disc
Corrective Action
Clean disc with soft cloth
Disc is upside down
Insert disc with label side up
Disc not present in loading compartment
Insert disc
Disc is dirty
Clean disc with soft cloth
Disc is upside down
Insert disc with label side up
Disc format is not compatible with this unit
Region Error
DVD is not compatible with region code of unit
Error
illegal mechanism operation
Press EJECT key for 5 seconds to reset loading mechanism
35
VM9511TS
Care and Maintenance
1.
2.
3.
4.
5.
6.
7.
8.
Use only a clean silicone cloth and neutral detergent to
clean the front panel or monitor. A rough cloth and nonneutral detergent (such as alcohol) may result in
scratching or discoloration.
Do not get water or cleaning fluids on the unit.
If the temperature inside the player gets too hot, a
protective circuit automatically stops play of the disc. If
this occurs, allow the unit to cool before operating the
player again.
Never insert anything other than a 5” (12 cm) compact
disc into the player as the mechanism can be damaged
by foreign objects.
Do not attempt to use a 3” (8 cm) CD-Single disc in this
unit, either with or without an adaptor, as damage to the
player and/or disc may occur. Such damage is not
covered by the Warranty on this product.
The CD player may not operate properly in extreme hot
or cold. If such conditions occur, allow the interior of the
vehicle to reach a normal temperature before using
player.
When the vehicle warms up during cold weather or
under damp conditions, condensation may appear on
the LCD panel. Should this occur, the screen will not
operate properly until the moisture has evaporated.
We suggest you use a cleaning disc in this unit more
frequently than in the unit in your home due to the
environmental conditions of the vehicle.
36
VM9511TS
SPECIFICATIONS
CEA Power Ratings
Main Amplifier
Power Output: 18 watts RMS X 4 channels into 4-ohms @ <
1% THD+N
Signal to Noise Ratio: 70dBA below reference. (Reference: 1
watt, 4-ohms)
Dynamic Power: 88 watts into 4-ohms, all channels driven
Frequency Response: 20Hz to 20kHz, -3dB. Aux input used
as source reference
Reference Supply Voltage: 14.4VDC
DVD/CD Player
Compatible Formats: DVD-R, DVD-RW, DVD+R, DVD+RW,
CD-R, CD-RW, CD-DA, MP3, WMA, HDCD, SVCD, VCD,
MPEG2, MPEG4, JPEG, MP3/WMA files burned onto a
DVD+R/W or DVD-R/W and Kodak Picture CD
Signal to Noise Ratio: 95dBA
Dynamic Range: >95dB
Frequency Response: 20Hz to 20kHz, -3dB
Channel Separation: > 60dB @ 1kHz
D/A Converter(s): 6-channel high performance 24-bit,
192kHz, multi-bit Sigma Delta modulation. DAC supports
sample rates from 8~192kHz.
Electronic Skip Protection (ESP): 16Mbit high-speed flash
memory
DVD: 2-3 sec, CD-DA: 10 sec, MP3: 100 sec, WMA: 200 sec
(ESP time is approximate)
SD Card Reader
Compatible Formats: MPEG, MPEG2, MP3 / WMA, MPEG4,
JPEG and Kodak Picture CD
Supports up to 2GB SD card
Video
Format: NTSC, PAL (auto-detection)
Output: 1Vp-p (75-ohm), buffered
Input: 1Vp-p (75-ohm)
FM Tuner
Tuning Range: 87.5MHz - 107.9MHz
Mono Sensitivity (-30dB): 9dBf
Quieting Sensitivity (-50dB): 15dBf
Alternate Channel Selectivity: 70dB
Signal to Noise Ratio @ 1kHz: 58dB
Image Rejection: 80dB
Stereo Separation @ 1kHz: 30dB
Frequency Response: 30Hz - 15kHz, -3dB
AM Tuner
Tuning Range: 530kHz - 1710kHz
Sensitivity (-20dB): 30uV
Signal to Noise Ratio @ 1kHz: 50dB
Image Rejection: 60dB
Frequency Response: 50Hz - 2kHz, -3dB
Monitor
Screen Size: 7.0" (Measured diagonally), 16:9 Widescreen
• 6.06" (154.1mm) W X 3.42" (87mm) H
Screen Type: TFT Liquid Crystal Display (LCD) active matrix
Response Time: 30mSec rise time, 50mSec fall time
Resolution, DVD/Composite Video in: 336,960 sub pixels,
1440 (W) X 234 (H)
Viewing angle:
• 65 degrees left or right
• 40 degrees up
• 65 degrees down
General
Auxiliary Input impedance: 10k
Power Supply: 11 to 16VDC, negative ground
Power Antenna (Blue): 500mA max, current limited protection
Amplifier Remote (Blue/White): 500mA, current limited
protection
Fuse: 15-amp, mini ATM type
DIN chassis dimensions: 7" X 7" X 2" (178mm x 178mm x
50mm)
Operating Temperature: -20C ~ 70C
* Specifications subject to change without notice.
12-MONTH LIMITED
WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the
original retail purchaser of this product that should this
product or any part thereof, under normal use and conditions,
be proven defective in material or workmanship within 12
months from the date of original purchase, such defect(s) will
be repaired or replaced with new or reconditioned product (at
the Company's option) without charge for parts and repair
labor. To obtain repair or replacement within the terms of this
Warranty, please contact Audiovox at the telephone number
provided below.
37
This Warranty does not extend to the elimination of car static
or motor noise, to correction of antenna problems, to costs
incurred for installation, removal, or reinstallation of the
product, or damage to tapes, compact discs, accessories or
vehicle electrical systems. This Warranty does not apply to
any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration,
improper installation, mishandling, misuse, neglect, accident,
or by removal or defacement of the factory serial number/bar
code label(s) or markings. THE EXTENT OF THE
COMPANY'S LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY
PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or
liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE
LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY MUST BE BROUGHT
WITHIN A PERIOD OF 12 MONTHS FROM DATE OF
ORIGINAL PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. No person or representative is authorized to
assume for the Company any liability other than expressed
herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or
consequential damage so the above limitations or exclusions
may not apply to you. This Warranty gives you specific legal
rights and you may also have other rights which vary from
state to state.
U.S.A: 1-800-323-4815
CANADA: Call 1-800-323-4815 for the location of a warranty
station serving your area.
Audiovox Electronics Corporation
Hauppauge, NY 11788
Technical Assistance: 1-800-323-4815
www.jensen.com
© 2006 Audiovox
Ver 1.0
Printed in China