FR
EN
DE
IT
ES
PT
EL
NL
DA
NO
FI
HW 131
SV
CS
PL
SL
SK
LT
BG
RU
HU
RO
TR
HR
LV
ET
cod. 90747 - EY
UK
FR Lire ce manuel avant l’installation/utilisation du nettoyeur en faisant très attention aux INSTRUCTIONS POUR LA SÉCURITÉ
EN Read this manual through carefully before installing/using the cleaner, paying special attention to the SAFETY
INSTRUCTIONS
DE Lesen Sie dieses Handbuch vor der Installation und dem Gebrauch des Hochdruckreinigers aufmerksam durch und achten
Sie besonders auf die SICHERHEITSANWEISUNGEN
IT
Leggere questo manuale prima dell’installazione/uso dell’idropulitrice, prestando particolare attenzione alle ISTRUZIONI
PER LA SICUREZZA
ES Leer este manual antes de la instalación/uso de la hidrolimpiadora, prestando particular atención a las INSTRUCCIONES
SOBRE SEGURIDAD
PT Leia este manual antes de instalar/usar a lavadora a alta pressão, prestando muita atenção nas INSTRUÇÕES PARA A
SEGURANÇA
EL Διαβάστε το παρόν εγχειρίδιο πριν από την εγκατάσταση/χρηση του μηχανήματος πλύσης, με ιδιαίτερη προσοχή στις
ΟΔΗΓΙΕΣ ΓΙΑ ΤΗΝ ΑΣΦΑΛΕΙΑ
NL Lees vóór de installatie/het gebruik van de hogedrukreiniger deze handleiding goed door en in het bijzonder de
VEILIGHEIDSVOORSCHRIFTEN
DA
NO
FI
SV
Læs denne vejledning inden installation og brug af højtryksrenseren og vær særligt opmærksom på SIKKERHEDSREGLERNE
Les denne håndboken før installasjon og bruk av høytrykksspyleren og vær spesielt oppmerksom på SIKKERHETSREGLENE
Lue tämä käyttöopas ennen painepesurin asennusta/käyttöä. Kiinnitä erityistä huomiota TURVAOHJEISIIN
Läs igenom bruksanvisningen före installation och användning av högtryckstvätten. Lägg speciellt märke till
SÄKERHETSBESTÄMMELSERNA
CS Před instalací nebo používáním tohoto čističe si pečlivě přečtěte tuto příručku. Zvýšenou pozornost věnujte části
BEZPEČNOSTNÍ POKYNY
PL Przed przystąpieniem do instalacji bądź użycia myjki należy dokładnie przeczytać niniejszy podręcznik, zwracając
szczególną uwagę na treść części dotyczącej INSTRUKCJI BEZPIECZEŃSTWA
SL Pozorno preberite ta navodila pred namestitvijo/uporabo čistilnika, pri čemer posebno pozornost namenite VARNOSTNIM
NAVODILOM
SK Pred inštaláciou/používaním čističa si pozorne prečítajte tento návod a buďte obzvlášť opatrní pri čítaní BEZPEČNOSTNÝCH
POKYNOV
LT
Prieš sumontuodami ir naudodami įrenginį atidžiai perskaitykite šią naudojimo instrukciją, ypatingą dėmesį atkreipdami
į SAUGOS INSTRUKCIJAS
BG Прочетете това ръководство внимателно, преди да инсталирате/използвате машината за почистване,
като обърнете особено внимание на ИНСТРУКЦИИТЕ ЗА БЕЗОПАСНОСТ
RU Прочитайте данное руководство перед установкой моечной машины, обращая особенное внимание на
ИНСТРУКЦИИ ПО БЕЗОПАСНОСТИ
HU A tisztítóberendezés üzembehelyezése/használata előtt olvassa át gondosan ezt a leírást, különös figyelmet szentelve a
BIZTONSÁGI ELŐÍRÁSOK című résznek
RO Citiţi acest manual în întregime cu atenţie înainte de a instala/utiliza aparatul de curăţat, acordând o atenţie mărită
INSTRUCŢIUNILOR DE SIGURANŢĂ
TR Hidro temizleyiciyi kurmadan/kullanmadan önce, EMNİYET BİLGİLERİ’NE özellikle dikkat göstererek, işbu kılavuzu
okuyunuz
HR Prije montiranja/korištenja čistača pažljivo pročitajte ovaj priručnik i posebnu pozornost posvetite SIGURNOSNIM
MJERAMA
LV Pirms tīrīšanas ierīces uzstādīšanas/izmantošanas izlasiet šo rokasgrāmatu, īpaši vērīgi lasiet DROŠĪBAS NOTEIKUMUS
ET Lugege see kasutusjuhend enne survepesuri töökorda seadmist/kasutamist hoolega läbi, pöörates erilist tähelepanu
OHUTUSNÕUETELE
UK Перед тим, як встановлювати/використовувати пристрій для миття, уважно прочитайте цей посібник,
звертаючи особливу увагу на ІНСТРУКЦІЇ З БЕЗПЕКИ
E3
E1
C3
C1
A1
A2
A3
A4
B6
B4
B5
B2
B1
B2
C2
B3
1
D
1
3
2
4
5
CH 17
6
Ø13
8
2
7
G
E
F
psi
0
max
bar
3
D
1
OFF
ON
I
2
4
H
L
M
CH 6
5
3 x 1,5 mm2
230
L1
N
S
4
1
25 ÷ 50 m
1 ÷ 25 m
Volt
5
3 x 2,5 mm2
a
r
M
1 ~
2
C
T
n
b
I
10
English
B1
B2
B3
B4
B5
B6
1 GENERAL INFORMATION (FIG.1)
EN
1.1
1.2
Use of the manual
This manual forms an integral part of the appliance and should be
kept for future reference. Please read it carefully before installing/
using the unit. If the appliance is sold, the Seller must pass on this
manual to the new owner along with the appliance.
1.2.1
1.3
1.4
2.4.1
Delivery
The appliance is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
Documentation supplied with the appliance
A1 Use and maintenance manual
A2 Safety instructions
A3 Declaration of conformity
2.5
Disposing of packaging
Safety signs
1.4.1
3.2
3.3
2.2
2.3
2.4
Envisaged use
This appliance has been designed for individual use for the cleaning
of vehicles, machines, boats, masonry, etc, to remove stubborn dirt
using clean water and biodegradable chemical detergents.
Vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
- Intake water temperature: see data plate on the appliance.
- Intake water pressure: below 10 bar.
- Operating ambient temperature over 0°C in accordance with
standard EN 60335-2-79/A1 only for domestic model (see symbol E3).
Operator
The symbol on the front cover identifies the appliance’s intended
operator (professional or non-professional).
Improper use
Use by unskilled persons or those who have not read and understood the instructions in the manual is forbidden.
The introduction of inflammable, explosive and toxic liquids into the
appliance is prohibited.
Use of the appliance in a potentially inflammable or explosive
atmosphere is forbidden.
The use of non-original spare parts and any other spare parts not
specifically intended for the model in question is prohibited.
All modifications to the appliance are prohibited. Any modifications
made to the appliance shall render the Declaration of Conformity
null and void and relieve the manufacturer of all liability under civil
and criminal law.
Main components
Nozzle cleaning tool
Rotating nozzle kit
Handle
Brush
Hose reel
Safety devices
Caution - Danger!
Assembly
Caution - Danger!
All installation and assembly operations must be
performed with the appliance disconnected from the mains
power supply.
The assembly sequence is illustrated in fig.2.
Assembling the rotating nozzle
(For models with this feature)
The rotating nozzle kit delivers greater washing power.
Electrical connection
Caution - Danger!
Check that the electrical supply voltage and frequency (V-Hz) correspond to those specified on the appliance
data plate (fig.2). The appliance should only be connected
to a mains power supply equipped with an adequate earth
connection and a differential security breaker (30 mA)
to cut off the electricity supply in the instance of a short
circuit.
2 TECHNICAL INFORMATION (FIG.1)
2.1
C1
C2
C3
C4
C5
3 INSTALLATION (FIG.2)
3.1
Symbols
E2 symbol – Indicates that the appliance is intended for
professional use, i.e. for experienced people informed
about the relative technical, regulatory and legislative
aspects and capable of performing the operations necessary for the use and maintenance of the appliance.
E3 symbol – Indicates that the appliance is intended for
non-professional (domestic) use.
Accessories (where applicable – see fig.1).
Do not tamper with or adjust the safety valve setting.
- Safety valve and pressure limiting valve.
The safety valve is also a pressure limiting valve. When the gun
trigger is released, the valve opens and the water recirculates
through the pump inlet.
- Safety catch (D): prevents accidental spraying of water.
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
Comply with the instructions provided by the safety signs fitted to
the appliance.
Check that they are present and legible; otherwise, fit replacements
in the original positions.
E1 sign – Indicates that the appliance must not be disposed of as
municipal waste; it may be handed in to the dealer on purchase of a
new appliance. The appliance's electrical and electronic parts must
not be reused for improper uses since they contain substances
which constitute health hazards.
Adjustable spray nozzle
Lance
Gun with safety catch
Power supply cable with plug
High pressure hose
Detergent tank (on models with this feature)
3.3.1
3.4
Use of extension cables
Use cables featuring “IPX5” protection level.
The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its
cross-section should be. See table I.
Water supply connection
Caution - Danger!
Only clean or filtered water should be used for intake.
The delivery of the water intake tap should be equal to that
of pump capacity.
Place the appliance as close to the water supply system as possible.
3.4.1
Connection points
3.4.2
Connection to the mains water supply
l Water outlet (OUTLET)
n Water inlet with filter (INLET)
The appliance can be connected directly to the mains
drinking water supply only if the supply hose is fitted with
a backflow preventer valve as per current regulations in
force. Make sure that the hose is at least Ø 13 mm and
that it is reinforced.
English
4 ADJUSTMENT INFORMATION (FIG.3)
4.1
4.2
4.3
4.4
Water flow is adjusted by regulating the nozzle (E).
Adjusting the detergent (on models with this feature)
Detergent flow is adjusted using the regulator (F).
Adjusting the detergent pressure
5.5
Set the adjustable nozzle on " " to deliver detergent at the correct
pressure (on models with this feature).
Adjusting the pressure (on models with this feature)
The regulator (G) is used to adjust the working pressure. The pressure is shown on the pressure gauge (where fitted).
5 INFORMATION ON USE OF THE APPLIANCE (FIG.4)
5.1
5.4
Adjusting the spray nozzle (for models with this feature)
5.6
Controls
- Starter device (H).
Set the starter switch on (ON/1) to:
a) start the motor (in models without TSS device);
b) set the motor ready to start (in models with TSS device).
If there is a pilot light on the starter device, it should light up.
If the “low/high” settings are available, use them as follows:
Low : low pressure washing
High : high pressure washing
Set the starter device switch on (OFF/0) to shut down the appliance.
If there is a pilot light on the starter device, it should go out.
- Water jet control lever (I).
5.7
5.3
Stopping the appliance
1) Set the starter device switch on (OFF/0).
2) Depress the gun trigger and discharge the residual pressure
inside the hoses.
3) Engage the gun safety catch (D).
Refilling and using detergent
When using detergent, the adjustable nozzle must be set on
" " (on models with this feature).
Fill the tank with highly degradable detergent.
Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to the
surface while still dry.
When dealing with vertical surfaces work from the bottom upwards.
Leave the detergent to act for 1-2 minutes but do not allow the
surface to dry. Starting from the bottom, use the high pressure jet
at a minimum distance of 30 cm. Do not allow the rinse water to run
onto unwashed surfaces.
Caution - Danger!
Start-up
Before starting up the appliance check that the water
supply hose is connected properly; use of the appliance
without water will damage it; do not cover the ventilation
grilles when the appliance is in use.
On three-phase models for professional use, at first use start the
appliance for a very short time to check that the motor is running
in the correct direction. If the motor fan is turning anti-clockwise,
exchange two of the three phase wires (L1, L2, L3) in the electrical
plug.
1) Turn on the water supply tap fully.
2) Release the safety catch (D).
3) Depress the gun trigger for a few seconds and start up the appliance using the starter device (ON/1).
TSS models - In TSS models with automatic delivery flow cut-off
system:
- when the gun trigger is released the dynamic pressure automatically cuts out the motor (see fig.4);
- when the gun trigger is depressed the automatic drop in pressure starts the motor and the pressure is restored after a very
slight delay;
- if the TSS is to function correctly all gun releasing and depressing operations must be performed at intervals of less than 4-5
seconds.
To prevent damage to the appliance, when running do not
stop the water jet for more than 10 minutes at a time.
Storage
1) Switch the appliance off (OFF/0).
2) Remove the plug from the socket.
3) Turn off the water supply tap.
4) Discharge the residual pressure from the gun until all the water
has come out of the nozzle.
5) Drain the detergent tank.
6) Engage the gun safety catch (D).
Any maintenance operations not covered by this chapter should be
carried out by an Authorized Sales and Service Centre.
During operation the appliance must be positioned
as shown in fig. 4 on a sturdy, stable surface.
Caution - Danger!
Restarting
1) Release the safety catch (D).
2) Depress the gun trigger and discharge the residual air inside
the hoses.
3) Set the starter device on (ON/1).
6 MAINTENANCE (FIG.5)
Caution - Danger!
5.2
11
6.1
6.2
6.3
6.4
Always disconnect the plug from the power socket
before carrying out any work on the appliance.
Cleaning the nozzle
1) Disconnect the lance from the nozzle.
2) Remove any dirt deposits from the nozzle hole using the tool
(C1).
Cleaning the filter
Clean the suction filter (L) and the detergent filter after every 50
hours of operation.
Unjamming the motor (on models with this feature)
In case of lengthy stoppages, limescale sediments may cause the
motor to seize. To unjam the motor, turn the drive shaft with a
tool (M).
End-of-season storage
Treat the appliance with non-corrosive, non-toxic antifreeze before
storing it away for winter.
EN
12
English
7 TROUBLESHOOTING
EN
Problem
Pump does not reach working
pressure
Possible causes
Nozzle worn
Water filter fouled
Water supply pressure low
Air being sucked into system
Air in pump
Pressure drops during use
Adjustable nozzle not positioned correctly
Water intake from external tank
Intake water too hot
Nozzle clogged
Insufficient power supply
Motor “sounds” but fails to start
Voltage loss due to use of extension cable
Appliance not used for a long period of time
Problems with TSS device
No electrical power
Motor fails to start
Problems with TSS device
Remedy
Replace nozzle
Clean filter (fig.5)
Turn on water supply tap fully
Check tightness of hose fittings
Switch off the appliance and keep depressing and releasing the gun trigger until the water comes out in a steady
flow. Switch the appliance back on again.
Turn the adjustable nozzle (E) (+) (fig.3)
Connect appliance to the mains water supply
Reduce temperature
Clean nozzle (fig.5)
Check that the voltage of the mains power supply line is
the same as that on the plate (fig.2)
Check characteristics of extension cable
Contact your nearest Authorized Service Centre
Contact your nearest Authorized Service Centre
Check that the plug is firmly in the socket and that the
mains voltage supply is present (*)
Contact your nearest Authorized Service Centre
Water leakage
Seals worn
Appliance noisy
Oil leakage
Water too hot
Seals worn
Using the tool (L) unjam the motor from the hole at the
rear of the appliance (in models with this feature) (fig.5)
Have the seals replaced at your nearest Authorized
Service Centre
Reduce temperature (see technical data
Contact your nearest Authorized Service Centre
Appliance not used for a long period of time
TSS versions only: motor starts
even with gun trigger is released
TSS versions only: no water delivery when gun trigger is depressed
(with supply hose connected)
Nozzle clogged
Clean nozzle (fig.5)
High pressure system or pump hydraulic circuit not
watertight
Contact your nearest Authorized Service Centre
Nozzle clogged
Clean nozzle (fig.5)
If the motor starts and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (overload cutout has been tripped).
If the problem recurs more than once, contact your nearest Authorized Service Centre.