EUROCOM 888ES Dream Machine Operating instructions

3-272-042-11 (2)
SONY;
Owner's Record
The model number and the serial number are located
on the rear exterior.
Record the serial number in the space provided below.
Refer to them whenever you call upon your Sony
dealer regarding this product.
Model No. ICF-CliP
Serial No.
FM/AM Clock Radio
ICF-C1iP
Operating Instructions
_
For customers who purchased this product in the
USA
Please register this product on line at
http://www.sony.comlproductregistration.
Proper registration will enable us to send you
periodic mailings about new products, services,
and other important announcements. Registering
your product will also allow us to contact you in
the unlikely event that the product needs
adjustment or modification. Thank you.
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
To reduce the risk of electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
To reduce the risk of fire, do not cover the ventilation
of the apparatus with newspapers. tablecloths,
curtains, etc. And do not place lighted candles on the
apparatus.
The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids. such
as vases. shall be placed on the apparatus.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
DREAM MACHINE
As the main plug is used to disconnect the unit from
the mains, connect the unit to an easily accessible AC
outlet. Should you notice an abnormality in the unit,
disconnect the main plug from the AC outlet
immediately.
Dream Machine is a trademark of Sony Corporation.
fb
NOPOWER
~
~NO PROBlEMJJ)
You are cautioned that any changes or
modifications not expressly approved in this manual
could void your authority to operate this equipment.
No Power No problem is a trademark of Sony Corporation.
&
.]~-
I
R IS K
_ O_F_E_LE_C_TR_IC_S_HO_C_K--li
DO NOT OPEN
L
_ - -_
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
© 2007 Sony Corporation
Printed in China
DO NOT REMOVE COVER (OR BACK)
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
http://www.sony.net!
IPortable Audiol
LIMITED WARRANTY (u.s.
Only)
Sony Electronics Inc. ("Sony") warrants this product against defects in material or workmanship for the time
periods and as set forth below. Pursuant to this Limited Warranty, Sony will, at its option, (i) repair the product
using new or refurbished parts or (ii) replace the product with a new or refurbished product. For purposes of this
Limited Warranty, "refurbished" means a product or part that has been returned to its original specifications. In
the event of a defect, these are your exclusive remedies.
Labor: For a period of one (1) yearfrom the original date of purchase of the product ("Labor Warranty"), Sony
will, at its option, repair or replace with new or refurbished product, product determined to be defective. If Sony
elects to replace the product after this Labor Warranty has expired but while the Parts Warranty below is still in
effect, it will do so for the applicable labor charge.
Parts: For a period of one (1) year from the original date of purchase of product ("Parts Warranty"), Sony will
supply new or refurbished replacement parts in exchange for parts determined to be defective.
This Limited Warranty covers only the hardware components packaged with the Product. It does not cover
technical assistance for hardware or software usage and it does not cover any software products whether or not
contained in the Product; any such software is provided "AS IS" unless expressly provided for in any enclosed
software Limited Warranty. Please refer to the End User License Agreements included with the Product for your
rights and obligations with respect to the software.
Instructions: To obtain warranty service, you must deliver the product, freight prepaid, in either its original
packaging or packaging affording an equal degree of protection to the Sony authorized service facility specified.
It is your responsibility to backup any data, software or other materials you may have stored or preserved on your unit. It is likely that such data, software, or other materials will be lost or reformatted
during service and Sony will not be responsible for any such damage or loss. A dated purchase receipt is
required. For specific instructions on how to obtain warranty service for your product,
Visit Sony's Web Site:
www.sony.com/service
Or call the Sony Customer Information Service Center
1-800-222-S0NY (7669)
For an accessory or part not available from your authorized dealer, call:
1-800-488-S0NY (7669)
Repair I Replacement Warranty: This Limited Warranty shall apply to any repair, replacement part or replacement product for the remainder of the original Limited Warranty period or for ninety (90) days, whichever is
longer. Any parts or product replaced under this Limited Warranty will become the property of Sony.
This Limited Warranty only covers product issues caused by defects in material or workmanship during ordinary
consumer use; it does not cover product issues caused by any other reason, including but not limited to product
issues due to commercial use, acts of God, misuse, limitations of technology, or modification of or to any part of
the Sony product. This Limited Warranty does not cover Sony products sold AS IS or WITH ALL FAULTS or
consumables (such as fuses or batteries). This Limited Warranty is invalid if the factory-applied serial number
has been altered or removed from the product. This Limited Warranty is valid only in the United States.
LIMITATION ON DAMAGES: SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT
IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations
on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This Limited
Warranty gives you specific legal rights and you may have other rights which vary from state to state.
D455714503
This unit includes a preinstalled Sony Lithium battery (CR2032) as back-up power source for the clock, which is preset
to EST/EDT (Eastern Standard Time/Daylight Time) at the factory. And this battery is considered part of the product.
This symbol is intended to alert the
user to the presence of uninsulated
"dangerous voltage" within the
product's enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
INFORMATION
This equipment has been tested and found to comply
with the limits for a Class B digital device. pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and recei ver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
WARNING
• Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type.
• Replace the battery for the clock backup with a
Sony CR2032 lithium battery, and the battery for the
remote commander with a Sony CR2025 lithium
battery. Use of another battery may present a risk of
fire or explosion.
• Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in fire.
• Do not expose the battery to excessive heat such as
direct sunlight, fire or the like.
• Dispose of used battery promptly. Keep away from
children.
Importan~ Safety Instructions
I) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles. and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture.
does not operate normally, or has been dropped.
For the state of california, USA only
Perchlorate Material -special handling may apply. See
www.dtsc.ca. govIhazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate
Features
• Dual alarm FM/AM Clock radio with iPod dock.
• Various type of alarms- iPod, radio and buzzer.
• Automatic time set - When you plug the clock in
for the first time. the current time will be shown in
the display.
• Automatic Daylight Saving Time/Summer time
adjustment.
• CLOCK button to display month. day and year.
• Brightness control (High/Middle/Low).
• No Power No Problem™ alarm system to keep the
clock and the alarm operating during a power
interruption with a CR2032 battery installed.
Troubleshooting
Should any problem occur with the unit, make the
following simple checks to determine whether or not
servicing is required.
If the problem persists, consult your nearest Sony
dealer.
The clock displays "AM 12:00" due to a
power interruption.
• The battery is low. Replace the battery. Remove the
old battery and install a new one.
When daylight saving time begins, the clock
does not employ the daylight saving time
automatically.
• Make sure the clock is set correctly.
• Press and hold CLOCK and TIME ZONE/ALARM
DISPLAY simultaneously for at least two seconds
to employ the DST function.
The alarm does not sound at the preset alarm
time.
• Has the desired alarm been activated? (i.e., Does the
ALARM A (or B) indicator light up?)
The radio or iPod alarm is activated but no
sound comes on at the preset alarm time.
• Has VOLUME been adjusted?
There is no sound from the iPod.
• Make sure the iPod is securely connected.
• Adjust the VOLUME.
The iPod cannot be operated with this unit.
• Make sure the iPod is securely connected.
The iPod cannot be charged.
• Make sure the iPod is securely connected.
Precautions
• Operate the unit on the power sources specified in
"Specifications" .
• To disconnect the power cord (mains lead), pull it
out by the plug, not the cord.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• Do not leave the unit in a location near a heat
source, such as a radiator or airduct, or in a place
subject to direct sunlight, excessive dust,
mechanical vibration, or shock.
• Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on a surface (a
rug, blanket, etc.) or near materials (a curtain) that
might block the ventilation holes.
• Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by qualified
personnel before operating it any further.
• To clean the casing, use a soft cloth dampened with
a mild detergent solution.
NOTES ON LITHIUM BATTERY
• Wipe the battery with a dry cloth to assure a good
contact.
• Be sure to observe the correct polarity when
installing the battery.
• Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
If you have any questions or problems
concerning your unit, please consult your
nearest Sony dealer.
Connecting the
antenna
To connect the AM loop
antenna
The shape and the length of the antenna is designed to
receive AM signals. Do not dismantle or roll up the
antenna.
1
2
3
Remove only the loop part from the plastic
stand.
Set up the AM loop antenna.
Connect the cords to the AM antenna
terminals.
The cords (A and B) can be connected to either
terminal.
Insert the cord while
pushing down the
terminal clamp.
I
~1-:z:z;D
~
Only insert up
to here.
Specifications
Time display
12-hour System
Frequency range
Band
Frequency
FM
87.5 - 108 MHz
AM
530 - 1 710 kHz
Speaker
Approx. 5.1 cm (2 inches) dia., 12 Q
Power output
3 W + 3 W (at 10% harmonic distortion)
Power requirements
120 V AC, 60 Hz
For clock backup: 3 V DC, one CR2032 battery
Dimensions
Approx. 300 x 130 x 139 mm (w/hld)
(11 I'/If> x 5 1/6 X 5 Ih inches) incl. projecting parts
and controls
Mass
Approx. 1.86 kg
battery
(4
Ib 1.61 oz) incl. CR2032
Supplied accessories
Remote commander ( 1)
Audio connecting cable (1 )
AM loop antenna ( 1)
Design and specifications are subject to change
without notice.
4 Make sure the AM loop antenna is
connected firmly by pulling softly.
Adjusting the AM loop antenna
Find a place and an orientation that provide good
reception.
• Do not place the AM loop antenna near the unit or
other AV equipment, as noise may result.
• If you use an external polarized AM antenna, be
sure to connect the ground cord to the rh terminal.
The supplied AM antenna cord has no polarity.
Tip
Adjust the direction of the AM loop antenna for best
AM broadcast sound.
About the backup
battery
To keep good time, as a backup power source, this
unit has one CR2032 battery inside of the unit in
addition to the house current.
The battery keeps the clock and the alarm operating in
the event of a power interruption.
Knowing when to replace
the battery
If a power interruption occurs when the battery is
weak, the brightness of characters in the display
darkens. If the battery runs out during the interruption,
the current time and alarm functions will be
initialized.
AUDIO IN
~
FM wire antenna
AC power cord
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may present a risk of
fire or explosion.
Replacing the backup
battery
1 Keep the AC plug connected to the AC
outlet, remove the screw that secures the
battery compartment at the bottom of the
unit using a screwdriver, and remove the
battery compartment. (See Fig. f.i.1-G))
Insert a new battery in the battery
compartment with the 0 side facing up.
2
,------~-----------------~
To remove the battery from the battery
compartment, push it out from the side marked
PUSH. (See Fig. r..t.1-®)
aB BB
~i.~EP' " • " " =~;7g7"od ~~
:
l_
....' l_-' :l_-' l_-' ~jfffOX1Wm ,',. BB •B
-'0-
ALARM A ALARM B TIME ZONE
ApMM
ALARMTIMEAB
WAKE UP VOL
FM 12 AM
There is a tactile dot on the VOLUME +,
•
~/II
3
Insert the battery compartment back into the
unit and secure it with the screw.
(See Fig. f.i.1-®)
STEREO
CMHz
JkHz
and PRESETTUNING 3 button.
Note
When you replace the battery, keep the AC plug
connected to a wall outlet. Otherwise. current time
and alarms will be initialized if the replacement is not
completed within around one minute.
Note
During the shipment and your first use, a clock error
may occur. In this case, refer to "Setting the clock and
date" to set the correct time.
When daylight saving time
(summer time) begins
This model employs the Automatic Daylight. Saving
Time/Summer Time adjustment. The DST indicator in
the display appears in the display at the beginning of
the daylight saving time (summer time), and
disappears at the end of it.
• Daylight saving time begins at: 2:00 AM on the
second Sunday of March.
• Standard time begins at: 2:00 AM on the first
Sunday of November.
To deactivate the Automatic
DST/Summer Time adjustment
during the daylight saving time
(summer time) period.
The Automatic DST/Summer Time adjustment can be
cancelled.
Press CLOCK and TIME ZONE/ALARM
DISPLAY for more than two seconds. The Automatic
DST/ Summer Time adjustment will be cancelled. To
active the Automatic DST/Summer Time adjustment
again, repeat the same operation.
Setting the clock
and date
To change the setting manually, follow the procedure
from step 1.
1
Press CLOCK for more than 2 seconds.
The year will start to flash in the display.
2
3
4
Press TIME SET + or - until the correct
year appears in the display.
Press CLOCK.
Repeat steps 2 and 3 to set the month, day
and time.
After setting the minute the clock starts from
o seconds. But if you do not set "Minute", the
If the time in the display is
incorrect after the battery
is changed (RESET)
Push the Reset switch with the pointed device. The
Reset switch is in the small hole located in the battery
compartment.
Notes
• You cannot reset unless the lithium battery is
installed.
• Set the clock again after the unit is reset.
CR2032
Battery Warning
When the unit will be left unplugged for a long time,
remove the battery to avoid undue battery discharge
and damage to the unit from battery leakage.
Preparing the
remote commander
Before using the card remote commander for the first
time, remove the insulation film. (See Fig. ID-CD)
clock does not start from 0 second flat.
• Pressing and holding + or - changes the year,
month, day or time rapidly.
• While setting the clock, you must perform each step
within about 65 seconds, or the clock setting mode
will be cancelled.
To display the year and date
Press CLOCK once for the date, and within
about 5 seconds press it again for the year.
The display shows the date or year for about
5 seconds and then changes back to the current time.
Setting the brightness
of the display
Three levels of brightness are available by
pressing SNOOZE/BRIGHTNESS.
Hit (default)
--->
Middle
--->
LOW]
When to replace the battery
With normal use, the battery (CR2025) should last for
about six months. When the remote commander no
longer operates the unit, replace the battery with new
ones. (See Fig. ID-®)
Notes
• Do not charge the battery.
• When you are not going to use the remote
commander for a long time, remove the battery to
avoid any damage caused by leakage and corrosion.
Setting the clock
for the first time
<D
This unit is preset to the current date and time at the
factory, and is powered by the back up battery. All
you need to do the first time is just plug it in and
select your time zone.
1
Area number "2" appears in the display.
If you live in the Eastern Time zone, you do not
need to adjust the area setting.
CR2025
Area number
Atlantic Standard/Daylight Time
2
Eastern Standard/Daylight Time
Central StandardlDaylight Time
4
Mountain StandardlDaylight Time
Pacific Standard/Daylight Time
6
Yukon Standard/Daylight Time
Hawaiian Standard/Daylight Time
3
4
Compatible iPod models
The compatible iPod models are as follows. Update
your iPod to use the latest software hefore you use it.
iPod nano 2nd
generation
(aluminium)
iPod 5th
generation (video)
iPod nann 1st
generation
iPod mini
iPod 4th generation
(color display)
iPod 4th
generation
Time zone
(default)
There is a tactile dot on the VOL +,
~ /11, t and PRESET + button.
You can enjoy iPod audio by connecting this unit. To
use an iPod, refer to the user's guide of your iPod.
Plug in the unit.
Press TIME ZONE for more then two
seconds.
2
888
Playing the iPod
Press TIME SET + or - repeatedly until
the desired number appears.
Press TIME ZONE to complete the setting.
Notes
• The connector of the unit is for sole use for iPod.
When you use the devices do not match with the
connector, connect it to the AUDIO IN terminal of
this unit with the supplied audio connecting cable.
• Sony cannot accept responsibility in the event that
data recorded to iPod is lost or damaged when using
an iPod connected to this unit.
1
Put the iPod into the unit's connector.
Tuning into a preset station
Playing the radio
1
2
-Manual Tuning
1
Press RADIO ON to turn on the radio.
The display shows the band and frequency.
PM
2
"."
, LI LI
"
B.LIn Un
ALARMTIMEA
BUZZER
AM
AM
3
Press RADIO ON to turn on the radio.
Press one of the PRESET TUNING
buttons where the desired station is stored.
Adjust volume using VOLUME.
Press RADIO ON repeatedly to select the
desired band.
Each press changes the band as follows:
CFMl ---+ FM2 ---+ AM J
You can fall asleep to the sound using the built-in
sleep timer that turns off the unit automatically after a
preset duration.
1
•
12 fi a ~H2
Setting the sleep
timer
Setting the alarm
Press SLEEP while the unit is turned on.
SLEEP appears in the display.
2
The dual alarm function allows you to set two alarm
programs (ALARM A and ALARM B).
The alarm time can be set for each program and the
alarm sound is selectable from RADIO, BUZZER or
iPod.
Press SLEEP to set the sleep timer
duration.
Each time you press SLEEP, the duration
changes as follows:
90
Notes
Adjust the rear support forward or backward
checking the back of the iPod fits snugly against
the rear support to protect the connector.
FM I and FM2 are the same frequency bands.
3
4
Use TUNING + or - to tune into the
desired station.
• Before setting the alarm, make sure to set the clock
(see "Setting the clock and date").
• The factory setting alarm time is "AM 12:00".
• To set the radio alarm, first tune in to a station
(see "Playing the radio").
The FM frequency advances or reverses in 0.1
MHz channel steps and the AM frequency in 10
kHz channel steps.
To set the alarm time
Adjust volunle using VOLUME.
To set ALARM A
To turn off the radio, press OFF.
1
2
Improving the
Reception
FM:
AM:
3
4
Extend the FM wire antenna fully to
increase reception sensitivity.
Connect the supplied AM loop antenna to
the unit. Rotate the antenna horizontally
for optimum reception.
Keep away iPod from the AM loop antenna or the FM
wire antenna, as this may lead to interference of
reception.
Tip
If the FM broadcast is noisy, press FM MODE on
the remote commander to turn off "STEREO" in the
display. The radio becomes clearer although the sound
becomes monaural.
Press ~/II.
2
The iPod begins to play automatically.
You can operate the connected iPod by the unit or
iPod buttons.
To
Press
Turn off the iPod
OFF, or press and hold
Pause playback
~/II
~II
To resume play, press it again.
Go to the next
track
Presetting Your
Favourite Station
-Preset Tuning
You can preset up to 10 stations in FM (5 stations in
FM I, 5 stations in FM2), and 5 stations in AM.
Presetting a Station
1 Follow steps 1 to 4 in "Playing the Radio"
and nlanually tune into the station you wish
to preset.
Go back to the
previous track
Locate a point
~ (forward) or .....
while listening to (backward) while playing and
the sound
hold it until you find the point.
~
2
Press and hold the desired PRESET
TUNING button for more than two
seconds for registration.
Locate a point
while observing
the display
(forward) or .....
(backward) in pause and hold it
until you find the point.
After the preset has finished, the preset number
appears on the display.
Go back to the
previous menu
MENU*
Example: To preset AM I 260 kHz onto preset
2 button.
Select a menu
item or a track
for playhack
iI~ *
Execute the
selected menu or
the playback
ENTER*
To set ALARM B, follow the same steps above using
ALARM B instead of ALARM A.
To change the display between ALARM TIME A and
ALARM TIME B, press TIME ZONE/ALARM
DISPLAY.
Notes
• When you use the radio alarm, the timed alarm
sounds with the last broadcasting station tuned to
before the power went off. When you set the radio
alarm, select the desired broadcasting station before
turning the power off.
• The ALARM A (or B) indicator flashes in the
display when the alarm sounds.
• If a second alarm sounds during a first (or the
SNOOZE function is active), the second alarm takes
priority.
• The alarm function works as usual at the beginning
and end day of the daylight saving time (summer
time). While the Automatic DST/Summer Time
adjustment is set, as a result, if the alarm is set at a
time skipped when the daylight saving time (summer
time) begins, the alarm is skipped, or if the alarm is
set at a time overlapped when the daylight saving
time (summer time) ends, the alarm sounds twice.
• If the same alarm time is set for both alarm
(ALARM A and B), the ALARM A takes priority.
a few seconds after
+
To preset another station, repeat these steps.
To change the preset station, tune into the desired
station and hold down the PRESET TUNING 1
to 5 button. The new station will replace the
previous station on the preset button.
To use the unit as a battery
charger
You can use the unit as a battery charger.
The charging begins when the iPod is placed on the
connector.
The charging status appears in the iPod display. For
details. see the user's guide of your iPod.
On copyrights
• iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
• All other trademarks and registered trademarks are
of their respective holders. In this manual. ™ and ®
marks are not specified.
30
~
15
To turn off the unit before the
preset time
Press OFF.
To use both sleep timer and
alarm
You can fall asleep to the radio and also be awakened
by the radio or buzzer alarm at the preset time.
1
Set the alarm. (See "Setting the alarm".)
2
Set the sleep timer. (See "Setting the sleep
tilner".)
Other useful functions
To get the MEGA Xpand effect
Press MEGA Xpand. "MEGA Xpand" appears in
the display. You can get the effect of expansion of the
sound field. To return to normal sound, press the
button again.
Connecting
external equipment
To listen to sound
1
Connect the AUDIO IN jack of the unit to
the line out jack or headphone jack of the
external equipment using the audio
connecting cable (supplied).
i-I
To activate the alarm
• The alarm sounds at the set time even if the unit is
on.
• Make sure the iPod is installed correctly after
setting the iPod alarm.
Press SNOOZE/BRIGHTNESS.
\'_~--.l
AUDIO IN
After setting the alarm time, follow these steps:
To activate the ALARM A, press ALARM
SET A to display ALARM A.
To activate the ALARM B, press ALARM
SET B to display ALARM B.
Audio connecting cable
(supplied)
To external
equipment
2
3
4
.-~
Press AUDIO IN to display "AUDIO IN".
Play the equipment connected to the
AUDIO IN jack.
Adjust the volUlne using VOLUME.
The sound turns off but will automatically come on
again after about 5 minutes.
The maximum length of the snooze time is 40 minutes.
To return to the radio
To stop the Alarm
Press RADIO ON.
The frequency is shown in the display.
Press OFF to turn off [he alann.
The alarm will come on sound again at the same time
the next day.
If OFF is not pressed, the buzzer alarm sounds
continuously for about 2 minutes, and then it stops
automatically.
The RADIO and iPod sound continuously until OFF
is pressed.
Tip
Apple's iPod Universal Dock Adapter can he used
with this unit.
~
ANTENNA
AM
To doze for a few more minutes
Notes
60
The display returns to clock mode five seconds
after you have finished setting the duration setting
and released SLEEP, and then the sleep timer
starts.
The unit will play for the duration you set, and
then shut off.
Notes
These operations are available only when using the
supplied remote commander.
• When placing or removing the iPod, keep it straight
and parallel with the rear support.
• Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
• When placing or removing the iPod, brace the unit
with one hand and take care not to press the controls
of the iPod by mistake.
• Do not pull on the rear support strongly as it cannot
be detached from the unit and may cause a
malfunction.
• To use an iPod. refer to the user's guide of your
iPod.
• Before disconnecting the iPod, pause playback.
5
Press ALARM SET A for a few seconds.
Press TIME SET +/- to set the desired
hour, and press ALARM SET A.
Press TIME SET +/- to set the desired
Ininute, and press ALARM SET A.
Press TIME SET +/- to set the desired
alarnl 1110de (RADIO, BUZZER or iPod)
and press ALARM SET A.
If you select the RADIO or iPod, press
TIME SET +/- to set the wake up
volume and press ALARM SET A.
~
L-OFF...---J
To deactivate the Alarm
Press ALARM SET A (or B) to turn off the
ALARM A (or B) indicator from the display.
Note on alarm in the event of a power
interruption
• When the alarm sound is set to RADIO or iPod, it
will change to BUZZER automatically.
• If the backup battery is exhausted, the alarm will not
work in the event of power interruption. Replace the
battery periodically.
To return to the iPod
Press
~/II.
To stop listening
Press OFF, and stop playback on the connected
unit.
PLEASE READ THE FOLLOWING REGARDING USAGE OF
THE APPLE® iPHONETM WITH THIS SONY PRODUCT
After placing the iPhone on this product, one of the following
messages will appear on the iPhone display:
"This Accessory is not made to work with iPhone" OK
OR
"This Accessory is not made to work with iPhone. Would you
like to turn on Airplane Mode to reduce audio interference
(you will not be able to make or receive calls)?"
By either pressing "OK" or "YES" or by waiting approximately
15 seconds with no action, the display will clear and you can
then begin playing music stored on the iPhone.
If you should need assistance with your Sony product,
we are here to help.
Answers to Frequently Asked Questions, Service Support
and other information can be found at:
www.sony.com/support
Our Customer Information Service Center can be reached at
1-800-222-S0NY (7669)