Sharp AR-P17 Software setupg guide Service manual

SERVICE MANUAL
CODE: 00ZARP17//A1E
DIGITAL MULTIFUNCTIONAL
SYSTEM OPTION
PRINTER EXPANSION KIT
MODEL
AR-PK1
AR-P17
CONTENTS
[1] SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[3] INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[4] SETTING AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[5] SIMULATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[6] CONFIGURATION REPORT AND TEST PAGE . . . . . . . . . . . . . . . . . . . . 6-1
[7] FLASH ROM VERSION UP PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . 7-1
[8] PRINTER STATUS MONITOR/PRINTER MANAGEMENT UTILITY . . . . 8-1
[9] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[10] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CONTENTS
[1] SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] SPECIFICATIONS
[5] SIMULATION
1. Operating procedures and operations . . . . . . . . . . . . . . . 5-1
1. Basic specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2. Simulation code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
2. Printer controller board . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
3. Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
3. IMC controller board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[6] CONFIGURATION REPORT AND TEST PAGE
4. Network specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
1. Kinds of test pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
5. Printer driver specification . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2. Print method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
A. System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
B. System requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
C. Print quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
D. Paper handling specifications. . . . . . . . . . . . . . . . . . . . 2-1
E. Print enable area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
F. Print reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
[3] INSTALLATION
1. AR-P17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
A. Parts included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
B. Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
C. Mounting of additional memory . . . . . . . . . . . . . . . . . . 3-2
2. AR-PK1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
A. Parts included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
B. Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
[4] SETTING AND ADJUSTMENTS
1. Printer condition settings . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
B. Operating procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
C. Setting item. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
2. AR-PK1 (PS expansion kit) setup . . . . . . . . . . . . . . . . . . . 4-2
A. Setup content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
B. Setup enable conditions . . . . . . . . . . . . . . . . . . . . . . . . 4-2
C. Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
D. Function cancel menu . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
3. Email alert status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
A. Setup contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
B. Setup enable conditions . . . . . . . . . . . . . . . . . . . . . . . . 4-2
C. Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
D. Function cancel display . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4. Key operator program list. . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
[7] FLASH ROM VERSION UP PROCEDURE
1. Printer Control Board firmware download method . . . . . . 7-1
2. Others (Troubleshooting) . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
[8] PRINTER STATUS MONITOR/PRINTER ADMINISTRATION
UTILITY
1. Printer status monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
A. Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
B. Operating environment . . . . . . . . . . . . . . . . . . . . . . . . 8-1
C. V3.1 limitations and notes . . . . . . . . . . . . . . . . . . . . . . 8-1
D. Outline of functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
2. Printer administration utility . . . . . . . . . . . . . . . . . . . . . . . . 8-3
A. Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
B. Operating environment . . . . . . . . . . . . . . . . . . . . . . . . 8-3
C. Outline of functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
D. Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
[9] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[10] ELECTRICAL SECTION
1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[1] SYSTEM CONFIGURATION
PCL CONTROLLER
CPU
COPIER
ENGINE
System-BUS
M
B
U
S
M
B
U
S
PCI-BUS
32bit/33MHz
P
C
I
U
S
B
Ethernet
USB2.0
(Full speed mode correspondence)
PC
1
2
8
4
[2] SPECIFICATIONS
Support OS
(Printer
Driver)
1. Basic specification
Item
Print Speed
Resolution
Smoothing
Standard memory
Expansion memory *2, 3
Option memory
Toner save mode
Input tray
Duplex Print
Finisher
NIC
PostScript Level3 *3
Bundled software
Barcode font
Operation Manual
Platform
Detail
AR-M276/M277:
27ppm (600dpi)
13.5ppm (1200dpi)
AR-M236/M237:
23ppm (600dpi)
13.5ppm (1200dpi)
300dpi, 600dpi, 1200dpi*1
1200dpi x 600dpi
64 MB
DIMM 1 slot
144 pin 128/256MB DIMM
8MB flash DIMM
Standard
Multi Bypass tray
Tray 1, Tray 2, Tray 3, Tray 4
(Depending on conditions of the
machine and option installation.)
Standard
Option
10/100baseTX (Standard equipped
with TCP/IP RF NIC. Others are
optional.)
Option
Printer driver, PAU, Status monitor,
Installer, Acrobat Reader
Option
Standard (Online manual)
IBM PC/AT (Include compatible
machine)
Macintosh
Option
PCI
Board
10/100BaseT
L
A
N
IO
ASIC
Energy-saving I/F
correspondence
P
C
I
PC
Item
Custom PS
Custom
PCL5e
Custom
PCL6
PPD only
PDL support
Resident
Fonts
For PS
Detail
Windows 95/98/Me
Windows NT 4.0
Windows 2000
Windows XP
Windows 95/98/Me
Windows NT 4.0
Windows 2000
Windows XP
Windows 95/98/Me
Windows NT 4.0
Windows 2000
Windows XP
Windows 95/98/Me
Windows NT 4.0
Windows2000
Windows XP
MacOS 8.6 to 9.x, 10.1 or later
PCL5e, PCL6, PostScript Level 3,
TIFF, PDF
136 Outline Fonts
For PCL5e,
80 Outline Fonts
PCL6
Line Printer
For PCL
Barcode Fonts (Option)
Screen Fonts For PS
136 Outline Fonts
For PCL5e,
136 Outline Fonts
PCL6
For PCL
Barcode Fonts (Option)
*1: 1200dpi mode print is supported only in PCL6 and PS3.
*2: Network scan needs one slot of memory (max. 256MB). When,
therefore, network scan is installed, the max. available memory for
the printer is 320MB.
*3: PDF direct print is available with PostScript.
2. Printer controller board
Processor
Base memory
Expansion
memory
Parallel I/F
USB I/F
Network I/F
AR-P17 SYSTEM CONFIGURATION 1 - 1
MIPS 64bit
64MB (Standard)
Standard: 144 pin DIMM x 1 slot
Max.: 320MB
IEEE 1284 compatible x 1
USB 2.0 (Full speed mode correspondence) x 1
10/100baseTX x 1
3. IMC controller board
Page memory
ROPM Base memory
ROPM Expansion memory
B. System requirement
48MB
32MB
Standard: 168 pin DIMM x 2 slot
Max.: 1056MB
Computer
IBM PC/AT (Include compatible machine)
Macintosh
Operating
system
Microsoft Windows 95
Microsoft Windows 98
Microsoft Windows Me
Microsoft Windows XP
Microsoft Windows NT 4.0
Microsoft Windows 2000
MacOS 8.6 to 9.x, 10.1 or later
4. Network specification
RF NIC
AR-NC5J
Interface
10Base-T
100Base-TX
10Base-T
100Base-TX
Support OS
Windows
Support Protocol
TCP/IP only
NetWare,
Windows NT,
Mac OS
IPX/SPX, TCP/IP,
EtherTalk, Peer to Peer
(IPX/SPX, TCP/IP),
NetBEUI
Note: Hardware requirements such as CPU and RAM for your operating system must be satisfied.
C. Print quality
Mode
Resolution
5. Printer driver specification
A. System
Machine
PCL6 PCL5e PostScript
Custom Custom Custom
OS
IBM PC/AT Windows 95
(Include
Windows 98
compatible
Windows Me
machine)
Windows NT 4.0
Smoothing *1
PPD
File
Toner Save Mode *1
Yes
Yes
Yes
Halftone
enhancement *1
Yes
Off
Windows 2000
Windows XP
Macintosh
Controll
(*: Default)
1200 dpi
600 dpi*
300 dpi
On
Off*
On
Off*
On*
Content
High Quality
Basic Resolution
Alternate Resolution
Smoothing function is ON.
Smoothing function is OFF.
Toner save function is ON.
Toner save function is OFF.
Halftone enhancement function
is ON.
Halftone enhancement function
is OFF.
*1: Functions on a image of 600dpi or 300dpi.
MacOS8.6 to
9.x, 10.1 or later
N/A
N/A
N/A
Yes
D. Paper handling specifications
(1) Paper feed direction
a. Paper size and image transfer direction
Name
A6R
B6R
Invoice
Invoice-R
A5
A5R
B5
B5R
Executive-R
Letter
Letter-R
A4
A4-R
Folio
Legal
Foolscap
B4
A3
Ledger
8K
16K
16KR
COM10
C5
DL
Transparency
Heavy stock
Label
Size
mm (inch)
Bypass
Tray
Tray 1
Tray 2
Tray 3
Tray 4
Duplex
105 × 148
128 × 182
215.9 × 139.7 (8.5” × 5.5”)
139.7 × 215.9 (5.5” × 8.5”)
210 × 148
148 × 210
257 × 182
182 × 257
186.7 × 266.7 (7.35” × 10.5”)
279.4 × 215.9 (11” × 8.5”)
215.9 × 279.4 (8.5” × 11”)
297 × 210
210 × 297
210 × 330 (8.3” × 13”)
215.9 × 355.6 (8.5” × 14”)
215.9 × 330.2 (8.5” × 13”)
257 × 364
297 × 420
279.4 × 431.8 (11” × 17”)
270 × 390
270 × 195
195 × 270
4.12 × 9.5
162 × 229
110 × 220
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
N/A
Yes
N/A
Yes
N/A
Yes
Yes
N/A
Yes
Yes
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Yes
Yes
N/A
Yes
Yes
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Yes
Yes
N/A
Yes
Yes
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Yes
Yes
N/A
Yes
Yes
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Yes
N/A
Yes
Yes
N/A
Yes
Yes
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
N/A
N/A
AR-P17 SPECIFICATIONS 2 - 1
Exit Tray
Center Upper
Tray
Tray
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Top
Tray
N/A
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
N/A
N/A
N/A
N/A
N/A
2tray Finisher
Offset
Staple
Tray
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Yes
Yes
Yes
N/A
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N/A
Yes
N/A
Yes
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Setting direction toward paper
feed port = Long side
Setting direction toward paper
feed port = Short side
Transfer direction
Transfer direction
Actual page
size
Print area
Logic paper
size
HP/GL
picture
frame
E. Print enable area
Actual page size
Print area
Logic paper size
HP/GL
picture frame
Paper
Size
A3
B4
A4
B5
A5
Ledger
Legal
Letter
Invoice
Foolscap
Folio
Executive
COM-10
C5
DL
∗ Top margin
A
B
C
D
E
F
G
H
9920
8597
7014
6070
4960
8400
8400
6600
5100
7800
7800
6300
5700
5408
5196
7014
6070
4960
4298
3508
5100
5100
5100
3300
5100
4980
4350
2474
3826
2598
9684
8361
6778
5830
4720
8160
8160
6360
2860
7560
7560
6060
3460
5172
4960
118
118
118
118
118
120
120
120
120
120
120
120
120
118
118
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
9720
8397
6814
5870
4760
8200
8200
6400
4900
7600
7600
6100
5500
5208
4996
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
The set value is received from the digital copier, and data are made
according to the set value.
A
B
C
D
E
F
G
H
7014
6070
4960
4298
3508
6600
5100
5100
3300
5100
4980
4350
2474
3826
2598
9920
8597
7014
6070
4960
10200
8400
6600
5100
7800
7800
6300
5700
5408
5196
6730
5786
4676
5770
3224
6300
4800
4800
3000
4800
4680
4050
2174
3542
2314
142
142
142
142
142
150
150
150
150
150
150
150
150
142
142
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
6814
5870
4760
4098
3308
6400
4900
4900
3100
4900
4780
4150
2274
3626
2398
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
∗ Left margin
Since the paper size sensor is not set, the digital copier cannot recognize the size and direction of paper which is actually inserted.
Therefore, the left margin is set according to the paper size specified in
the print data sent from the computer, and print process is performed.
If the computer does not specify the paper size, or in the case of the
custom size, the left margin is set according to the default paper size.
F. Print reference
This machine employs the center reference system.
Since the digital copier is not provided with the tray size detection feature, formatting and center distribution are performed not by the actual
paper size but by the paper size specified by the computer.
Origin
Paper feed direction
Paper
Size
A3
B4
A4
B5
A5
Ledger
Legal
Letter
Invoice
Foolscap
Folio
Executive
COM-10
C5
DL
AR-P17 SPECIFICATIONS 2 - 2
ABCDEFGHIJKLMN
12345
abc
Actual paper size
Size specified by the HOST
Center reference line
[3] INSTALLATION
2) Cut and remove the cut-out portion from the left rear cabinet.
Cut and remove the cut-out portion from the left rear cabinet using
a tool such as nippers. (Be careful about the direction of the tool so
that the cut surface is flat.)
1. AR-P17
A. Parts included
CD-ROM: 1 pc.
Operation manual
Installation caution
sheet
Cut-out portion
PCL PWB: 1 pc.
M3 screws: 3 pcs.
(For installation of
the parallel and the
USB connectors)
M3 screws with
spring washer: 6 pcs.
(For installation of the
PCL PWB)
3) Attach the PCL PWB unit.
Support post: 2 pcs.
B. Installation procedure
Attach the support post to the mounting plate of machine options.
Then connect the PCL PWB connector to the mother board connector and fit the PCL PWB with the six screws with M3 spring
washer (packed with the unit).
Turn off the main switch of the copier and then remove the power
plug of the copier from the outlet.
Then, attach the parallel and USB connector portion using the supplied three screws.
1) Remove the shielding plate.
Remove five screws and remove the shielding plate.
M3 screws with
spring washer
Support
post
Screws
M3 screw
M3 screws
PCL PWB
M3 screws with
spring washer
Screws
4) Attach the shielding plate.
Attach the shielding plate using five screws.
Screws
Screws
AR-P17 INSTALLATION 3 - 1
Insert the power plug of the copier to the outlet and turn on the
main switch. Then, carry out the following procedure.
5) Check for the PCL PWB.
3) Check the PS3.
Make the following sequence of selections on the control panel.
• Press Special Functions , highlight Configuration and press OK.
Press the PRINT key on the operation panel to check to see if the
copier enters the print mode.
6) Check for the language.
Check for the language setting (26-22) following the procedure
described in the service manual (section of simulation).
7) Check for printing.
• Use the up and down keys to highlight Test print menu and
press OK.
• Use the up/down keys to highlight Configuration page and press
OK.
A configuration page will be printed.
Check that the option memory capacity is 128 MB or more.
For installation of printer drivers on a computer, see the supplied
operation manual.
Check that the PS3 has been installed.
Then, connect a parallel cable to the computer and execute printing to check to see if printing can be executed properly.
Please keep below important information.
This information will use for other products.
C. Mounting of additional memory
(After mounting it, Installation proceed to step 4.)
Insert the memory module until it clicks.
The memory module is lock when it is inserted. However, be sure to
check that the module slit is engaged with the connector rib when it is
inserted.
APPLICATION
NUMBER
MACHINE
SERIAL
NUMBER
PRODUCT
KEY
Memory module
(S.O.DIMM)
2. AR-PK1
A. Parts included
CD-ROM: 1*
License agreement
Installation caution sheet
*NOTE: Do not use the CD-ROM packed in AR-PK1, but use the CDROM packed together with the AR-P17 for setting the PS
driver.
B. Installation procedure
To enable the PS3, the product key must be acquired.
(For the method of acquiring the product key, contact the SHARP
authorized dealer.)
1) Check that AR-P17 operates normally.
• Turn on the power and wait until warming up is complete.
• Press the PRINT key on the operation panel of the main unit.
• If the LCD in the operation panel of the main unit switches to the
print mode normally, AR-P17 is operating normally.
• If it is not operating normally, follow the AR-P17 Installation Manual to check and modify the system configuration settings and
check the operation.
2) Enable the PS3.
To enable the system configuration, use the keys on the main unit
to set the mode.
Enter the product key with the key operator program. (Refer to the
Operation Manual of Key Operator Program.)
Setting of the product key is complete. To update the system,
press the CA key to exit the setting mode.
AR-P17 INSTALLATION 3 - 2
[4] SETTING AND ADJUSTMENTS
5) To terminate setting, touch the [END] key.
CONDITION SETTINGS
1. Printer condition settings
EXIT
DEFAULT SETTINGS
PCL SETTINGS
A. List
PostScript SETTINGS
Item
Default settings
Toner save
Copies
Orientation
Default paper size
Default
OFF
1
Portrait
AB series: A4
Inch series: 8 1/2 x 11
Auto
Auto
OFF
600dpi
OFF
1-sided
ON
OFF
Default paper source
Default paper type
Smoothing
Resolution
Extra print mode
2-sided print
Page protection
ROPM
PCL settings
PCL symbol set setting
PCL font setting
Line feed code
Wide A4
PostScript settings*
Print PS errors
3 (PC-8)
Internal font: 0 (courier)
0
OFF
OFF
* Displayed when installing the PS expansion kit (AR-PK1).
B. Operating procedure
1) Press the [PRINT] key.
The basic menu of the printer mode is displayed.
COPY
PRINT
ON LINE
DATA
SCAN
DATA
2) Touch the [CONDITION SETTINGS] key.
Any print jobs that have already been sent to the machine, including print hold jobs stored in the machine, will be printed using the
printer condition settings that were effect when the job was sent.
ONLINE
OFFLINE
BYPASS SELECT
CONDITION
SETTINGS
DELETE
3) Touch the target item to display the setting menu.
EXIT
CONDITION SETTINGS
DEFAULT SETTINGS
PCL SETTINGS
PostScript SETTINGS
4) On the setting menu of the target item, set the desired set value
and touch the [OK] key.
To set another item continuously, repeat procedures 3) and 4).
C. Setting item
Default settings
Set value
Description
(*: Default value)
Toner save ON, OFF*
Sets whether toner save mode is in
effect or not. Toner is saved by
printing a little lighter. When the
resolution is 1200dpi, toner save
does not function.
Copies
1* – 999
Sets how many copies to print.
Orientation Portrait*,
Sets the page orientation for printing.
Landscape
Specify "PORTRAIT" to print the
paper with its long side (longer edge)
vertical. Specify "LANDSCAPE" to
print the paper with its long side
(longer edge) horizontal.
Default
5 1/2 x 8 1/2,
Sets the size of the paper where
paper size
8 1/2 x11*,
data will be printed. If this size is
different from the paper size present
8 1/2 x 13,
8 1/2 x 14,
in the tray, the size set for this item
11 x 17, A5,
takes precedence.
B5, A4*, B4, A3 * Depending on where the printer
was purchased, the default value is
either "A4" or "Letter".
Default
AUTO*,
Sets the tray used for paper feeding.
paper source BYPASS
When set to "Auto," the tray loaded
(MANUAL),
with the paper set by "Default paper
BYPASS (AUTO) size" is automatically selected.
TRAY1,
* Tray 3 and 4 (option) can be
TRAY2,
selected only when installed.
TRAY3,
TRAY4
Default
AUTO*, PLAIN, Select the paper type to be used.
paper type
RECYLED,
When set to "Auto," the tray loaded
LETTER HEAD, with the paper set by "Default paper
COLOUR
size" is automatically selected.
Sets whether smoothing is done or
ON, OFF*
Smoothing
not. Angles and curves included in an
image are smoothed to improve the
image quality. If smoothing is set
when the resolution is set to 600dpi,
an image corresponding to 1200dpi is
printed. (Printing at 1200dpi provides
a higher print quality, but consumes a
greater memory space, resulting in a
low print speed. When the resolution
is set to 1200dpi, smoothing cannot
be selected.) To print a bitmap image,
it is better not to select smoothing to
have a better print quality.
Resolution
300dpi, 600dpi*, Sets the printing resolution. When
1200dpi
1200dpi is selected, smoothing and
toner save cannot be selected.
Since 1200dpi printing consumes a
large memory space, resulting in a
low print speed.
Item
OK
DEFAULT SETTINGS
TONER SAVE
COPIES
1
ORIENTATION
P
AR-P17 SETTING AND ADJUSTMENTS 4 - 1
Set value
Description
(*: Default value)
Extra print
ON, OFF*
This function is used to reduce wait
mode
time between print jobs and
proceeds efficient print processes
mainly when there are many single
print jobs. Normally it is not used.
When this function is set, multiple
print jobs are processed as a single
job when all of the jobs have the
same print format. On the job status
display, it is displayed with one job
key. When printing is made with the
print hold function, this function
does not work. When the print type
is changed such as when the paper
size is changed, this function is
terminated.
When "2-SIDED (BOOK)" is
2-sided print 1-SIDED*,
2-SIDED
selected, duplex print is made on
(BOOK),
the assumption that the left edge of
2-SIDED
paper is bound. When "2-SIDED
(TABLET)
(TABLET)" is selected, duplex print
is made on the assumption that the
top of paper is bound.
Page
ON*, OFF
Sets page protection. Page
protection
protection is a function designed to
prevent data loss errors when
complex data is printed.
Sets whether the ROPM function is
ROPM
ON, OFF*
enabled. If the ROPM function is
enabled, print data will be stored in
the printer memory once for printing
onto multiple sheets. This function can
reduce transmission quantity between
the printer and your computer.
Item
Wide A4
Set value
Description
(*: Default value)
ON, OFF*
When this item is set, 80 digits of
10CPI font can be printed in one line
on A4 size paper. When setting is
canceled, the print digit number in
one line becomes 78 characters.
PostScript settings
"PS setting" is allowed only when the PS expansion kit is installed.
Item
Print PS
errors
Set value
Description
(*: Default value)
ON, OFF*
When it is set, if a PostScript error
occurs, the error content is printed.
2. AR-PK1 (PS expansion kit) setup
A. Setup content
• The soft key is supplied by registering the manufacturing number
and the model name of the machine and the application number
attached to the PS expansion kit via the Web site.
Enter the soft key to the machine, and the PS3 function can be operated.
If, however, the setup enable conditions are not satisfied, inputs are
disabled.
• When the soft key is erroneously inputted:
When the function lock is canceled: the function lock turns to work.
When the function lock is working: the function lock is kept working.
B. Setup enable conditions
• The printer expansion kit (including the standard equipment) should
be installed.
• The Japanese font ROM should be installed to the printer board.
(Japan only)
• The printer function should be provided as standard provision.
C. Setup menu
PCL settings
Set value
Description
(*: Default value)
Specify the PCL symbol set.
PCL symbol 1 – 35 (3*)
set setting
The number of the PCL symbol set
can be checked by printing [PCL
symbol set list] in [list print] of
CUSTOM SETTING.
PCL font
Internal font
The PCL font to be used for printing
setting
(0* – 80),
can be specified. One type of font can
extended font
be selected from the internal fonts or
(1 –)
the expansion fonts (bar code font kit
or flash ROM kit). The default is "0"
(Internal font: Courier).
The types of available fonts can be
checked by printing the font list in
the [list print] of the [CUSTOM
SETTING]. The font list includes the
font names, the numbers and print
out sample assigned to the fonts. In
this setting, the number assigned to
the font to be used is set.
Line feed
0* – 3
The line feed code is set by
code
combination of "CR" (Carriage
Return) code, "LF" (Line Feed"
code, and "FF" (Form Feed) code.
The default is set so that printing is
made by the sent code. To change
the setting, there are four kinds of
combination to select.
Item
Item
Enter the soft key the machine from “KEY OPERATOR MENU".
D. Function cancel menu
• When the diag menu or the key operator program menu is displayed,
the current machine state (the key is canceled or not) is displayed.
• Display content
ON: The function lock is working.
OFF: The function lock is canceled.
• Regardless of the display position
3. Email alert status
A. Setup contents
• The soft key is supplied by registering the manufacturing number
and the model name of the machine and the fixed application number via the Web site.
Enter the soft key to the machine, and the email alert and status
function can be operated.
If, however, the setup enable conditions are not satisfied, inputs are
disabled.
• When the soft key is erroneously inputted:
When the function lock is canceled: the function lock turns to work.
When the function lock is working: the function lock is kept working.
B. Setup enable conditions
• The printer expansion kit (including the standard equipment) should
be installed.
• The network card kit (NIC) should be installed.
C. Setup menu
Enter the soft key the machine from “KEY OPERATOR MENU".
AR-P17 SETTING AND ADJUSTMENTS 4 - 2
D. Function cancel display
• When the diag menu or the key operator program menu is displayed,
the current machine state (the key is canceled or not) is displayed.
• Display content
ON: The function lock is working.
OFF: The function lock is canceled.
• Regardless of the display position
4. Key operator program list
Key operator programs
Print settings
Default settings
Interface settings
Set value (∗: Default value)
Prohibit notice page printing
Print density level
Prohibit test page printing
Rotated print
Forced output of print
Exclude bypass-tray from ATS
Disable default setting changes
Hexadecimal dump mode
I/O timeout
Parallel port emulation switching
USB port emulation switching
Network port emulation switching
Port switching method
Network settings
(When the print server
card installed.)
Initialise and/or store
settings
Enable parallel port
Enable USB port
Enable network port
Enable ECP
IP address
DHCP
setting
IP address
IP subnet mask
IP gate way
Enable TCP/IP *1)
Enable NetWare *1)
Enable EtherTalk *1)
Enable NetBEUI *1)
Reset the NIC
Restore factory default
Store current configuration
Restore configuration
ON / OFF∗
1 / 2 / 3∗ / 4 / 5
ON / OFF∗
ON∗ / OFF
ON / OFF∗
ON∗ / OFF
ON / OFF∗
ON / OFF∗
1 – 999 (Increment of 1sec.) 60 (sec.)∗
Auto∗ / PostScript (When the PS3
expansion kit is installed.) / PCL
Auto∗ / PostScript (When the PS3
expansion kit is installed.) / PCL
Auto∗ / PostScript (When the PS3
expansion kit is installed.) / PCL
Switch at end of job∗ / Switch after I/O
timeout
ON∗ / OFF
ON∗ / OFF
ON∗ / OFF
ON / OFF∗
ON∗ / OFF
ON∗ / OFF
ON∗ / OFF
ON∗ / OFF
ON∗ / OFF
ON∗ / OFF
ON∗ / OFF
ON∗ / OFF
—
—
—
—
AR-P17 SETTING AND ADJUSTMENTS 4 - 3
Remarks
To enable the changed setup, the
power must be rebooted.
*1) Displayed when the AR-NC5J is
installed. Not displayed when only
the AR-P17 is installed.
To enable the changed setup, the
power must be rebooted.
[5] SIMULATION
24-9
1. Operating procedures and operations
Purpose
Function
(Purpose)
* Entering the simulation mode
1) #/P key (program) ON → Asterisk (*) key ON → CLEAR key ON →
Asterisk (*) key ON → Ready for input of a main code of simulation
2) Entering a main code with the 10-key → START key ON
3) Entering a sub code with the 10-key → START key ON
Data clear
Used to clear the printer counter and other counters.
(The counter is cleared after completion of
maintenance.)
Section
Printer
Item
Counter
Printer
Operation/procedure
1. Select the counter to be cleared with the 10-key.
4) Select an item with the scroll key and the item key.
5) The machine enters the mode corresponding to the selected item.
Press START key to start the simulation operation.
2. Press the [START] key.
The confirmation menu is shown.
3. Select "1: YES."
To cancel the current simulation mode or to change the main code
and the sub code, press the CUSTOM SETTINGS key.
1: YES (Cleared)
2: NO (Not cleared) (Default)
* Canceling the simulation mode to return to the normal mode
1) Press CLEAR ALL key.
1
2
3
4
2. Simulation code list
Code
Main
Sub
22
1
24
9
67
14
Item
PRINTER
IMC
DUPLEX
OTHERS
Content
Printer counter
IMC counter
DUPLEX counter
The other counters
Function
Used to check the counter value of each section.
Used to clear the printer counter and other
counters. (The counter is cleared after completion
of maintenance.)
Used to check write/comparison of flash programs.
67-14
3. Details
Purpose
Flash ROM version up
Function
Used to check write/comparison of flash programs.
(Purpose)
Section
Printer
Item
Operation
Operation/procedure
22
22-1
Purpose
Function
(Purpose)
Item
Adjustment/setting/operation data output/check
(display/print)
Used to check the counter value of each section.
Counter
Operation/procedure
Each counter is displayed.
TOTAL
MAINTENANCE
DEVE
DRUM
COPY
PRINTER
IMC
DUPLEX
OTHERS
FAX SEND
FAX RCV
FAX OUTPUT
Total
Maintenance
Developer counter *1
Drum counter
Copy counter
Printer counter
IMC counter
Duplex counter
The other counters
FAX Send counter
FAX receive counter
FAX print counter
1. Press the [START] key.
"PLEASE SEND DATA" is displayed.
2. Data are sent from the PC (MS-DOS) by use of "fcopy" command
(FCOPY: file name). (Refer the “[ 7] FLASH ROM VERSION UP
PROCEDURE”)
Used to overwrite and check the flash device while displaying its
process status.
After completion, the result is displayed.
3. Press the [CA] key to cancel the simulation and reset.
(Flash Device)
PROGRAM
BOOTROM
PS KANJI FONT
ESC/P KANJI FONT
OPTION FONT
(Processing state)
RECEIVE
ERASE
WRITE
VERIFY
* Execution of the simulation which performs communication with the
PCL board is inhibited until Notice Page storage is completed. (Only
when the serviceman call error occurs.)
In the other case than the serviceman call error, entering the simulation is inhibited during the system check operation is displayed.
The counter display is in 7 digits.
AR-P17 SIMULATION 5 - 1
[6] CONFIGURATION REPORT AND TEST PAGE
1. Kinds of test pages
2) Touch the [LIST PRINT] key.
Test pages are available in the following 6 kinds:
• Printer settings list
• PCL symbol set list
Y
T
LIST PRINT
S
• PCL internal font list
• PCL extended font list (Only when an option font or an option Flash
ROM kit is installed. When a Flash ROM kit is installed, it is displayed only when fonts are downloaded.)
• PCL internal font list (With PS installed)
• PS extended font list (Displayed only when PS is installed, an option
Flash ROM is installed, and fonts are downloaded.)
RECEIVE MODE
3) Touch the [PRINTER TEST PAGE] key.
PRINTER TEST PAGE
• NIC page
2. Print method
1) Press the [CUSTOM SETTINGS] key.
4) Touch the list key to be printed.
LINE
DATA
B STATUS
CUSTOM SETTINGS
PRINTER SETTINGS
LIST
PCL INTERNAL FONT
LIST
PCL SYMBOL SET
LIST
PCL EXTENDED FONT
LIST
* It is printed by priority even when there is a job waiting for printing.
AR-P17 CONFIGURATION REPORT AND TEST PAGE 6 - 1
[7] FLASH ROM VERSION UP
PROCEDURE
1. Printer Control Board firmware
download method
Please follow the procedure below:
(Necessary items for version-up)
1)
Make sure copier is turned off, and connect PC and Printer Control
board of the copier by parallel cable beforehand.
A
Personal computer
B
Centro (printer) cable
∗ Note: It is okay to use serial cable instead.
C
Software for version-up
2)
Turn on the copier.
3)
Start up in copier test command mode, and execute Sim67-14
"FLASHDOWNLOAD".
4)
And then, press OK key when notice message "PRESS OK KEY"
appears on the panel. Another message "Please Send Data" will
appear after a while.
5)
Start up the maintenance program on PC. Select model name
"AR-M236/M276/M237/M277 Series" from the model selection
dialogue box.
6)
Expand "Printer Control Board", and double-click on "Printer Control Board Firmware Download".
(ROM type)
The flash ROM is directly installed to each PWB.
(Target PWB)
1
PCL PWB
Outline of Version-up Procedure
(PC)
C
A
Download
data
RS232C connector
(9pin or 25pin)
Centro connector
B
Centro cable
I/F circuit (9pin)
MCU-PWB
Double click it.
Centro connector
PCL-PWB
1
Operation
panel
IMC
PWB
FAX-PWB Finisher
7)
Dialog box will appear to select download file.
8)
Select Download file(*.sfu) and press "Open" button.
9)
Download procedure will starts automatically.
(AR-M236/M276/M237/M277)
Prepare following files necessary for program download
• Maintenance software: maintenance.exe
• Andromeda module file: ProcModelC.mdl (for AR-M236/M276/
M237/M277 series)
10) Notice message "Data Send Complete" will appear on PC.
11) Notice message "Download is complete. Check the copier panel
to make sure the download is complete." will appear on PC.
12) Close maintenance program, and reset the machine by pressing
CA key.
This is the end of the download procedure.
AR-P17 FLASH ROM VERSION UP PROCEDURE 7 - 1
2. Others (Troubleshooting)
Followings are the error possibly occur during the download process and troubleshooting method.
No
1
Warning/error message
Incorrect destination. Continue with the
download process?
2
Incorrect download file.
3
No downloadable data included.
4
This option not available.
5
The data size exceeds the Flash ROM size.
Try again with the appropriate size of data.
6
Time out error.
7
Communication (incoming) error.
8
Checksum error.
9
Error during the download process. Error
code: 0xXXXXXXXX
10
An error. [0xXXXXXXXX]
Detail
Destination of download file and copier doesn't match.
Possible to select either continue or cancel the job.
[TROUBLESHOOTING]
To change destination, select "Yes". If not, select "No" and cancel download process.
Invalid download file for the machine is selected, or the file format is not correct.
[TROUBLESHOOTING]
Confirm the download file. Possibly the improper download file is selected.
Unable to find appropriate data in selected download file.
[TROUBLESHOOTING]
Confirm the download file. Possibly the improper download file is selected.
Download procedure is executed on uninstalled optional kit.
[TROUBLESHOOTING]
Confirm installed optional kit.
Confirm the download file. Possibly the improper download file is selected.
Panel flash ROM size is not enough to execute download procedure.
[TROUBLESHOOTING]
Confirm the download file. Possibly the improper download file is selected.
Exchange the flash ROM to the one which has more capacity.
Transmission error
Unable to receive data from the machine among the certain period of time.
[TROUBLESHOOTING]
Restart maintenance program after confirming communication port or communication cable.
Incorrect download procedure.
The machine did not proceed download procedure correctly.
[TROUBLESHOOTING]
Restart maintenance program after confirming communication port or communication cable.
Make sure the communication device of PC(either COM or parallel) is under right condition.
Transmission error
The check sum value of the transmission data is mismatch.
[TROUBLESHOOTING]
Restart maintenance program after confirming communication device of PC (either COM or
parallel) is under right condition.
Download data file operation error.
[TROUBLESHOOTING]
Restart maintenance program after confirming the selected download file is not abnormal and
not using other application.
The error occurred except the above errors.
[TROUBLESHOOTING]
Restart maintenance program after confirming communication device of PC(either COM or
parallel) is under right condition.
AR-P17 FLASH ROM VERSION UP PROCEDURE 7 - 2
[8] PRINTER STATUS MONITOR/PRINTER ADMINISTRATION UTILITY
1. Printer status monitor
D. Outline of functions
A. Purpose
(1) Status display
• Is printing enabled or disabled?
Simple view: For beginners
• Is toner sufficiently supplied?
Detailed view: For experts
• Is paper sufficiently supplied?
Simple/Detailed selection allowed
• Is duplex print enable?
(2) Status change notification
• Is the previous printing completed?
Device status when the machine is sending a job
This application provides easy and simple view of the above items.
Print enable
B. Operating environment
Print disable
Windows95, Windows98, WindowsMe, WindowsNT4.0 Workstation
(SP3 or later), Windows2000 Professional, Windows XP Home Edition
Professional TCP/IP necessary
C. V3.1 limitations and notes
Paper jam
Toner empty
Toner Low
Printer Warning
Paper Empty
(1) Requisites of printer to be monitored
Cover open
• The printer driver should have been installed. (Necessary)
Off-line
• The driver should allow peer-to-peer printing.
For the AR-M237/M277/M236/M276 series, the SC-Print2000 (Windows 95/98/Me) should be installed, and the "Print destination port"
of the printer should be set to TCP/IP port,
Printer error (Service call)
Output Tray Full
Notifying method:
Status window pop-up
or
• In the case where the driver is shared with the printer server, the
printer should be connected with TCP/IP. In this case, monitoring is
allowed after printing once.
Tip pop-up
Sound
(3) Selection of printer to be monitored
(2) Install and uninstall
The printer to be monitored can be switched by the following two ways.
In the case of WindowsNT/2000/XP, the administrator authority is
required for install and uninstall.
• Switch by the printer menu
(3) Status display when in the auto power shut off
(4) Job complete notification
The status information when the printer is in the "Auto power shut off"
mode is the status information immediately before entering the "Auto
power shut off mode.
Status of the job which was sent by the machine
• Switch by the setting dialog
Print complete
Temporary interruption of print by an error
1)
2)
3)
4)
1) Tool bar
Displays the status window, revises the display to the latest state,
makes setups, and displays Help.
3) Tip
Turns on for a certain time (when setting) when the status
changes.
2) Status window
Displays the printer status.
Selection of Simple/Detailed view is allowed.
Pop-up to indicate a change in the status is also allowed by setup.
4) Task tray icon
Memory-resident. Displays the printer status which is monitored.
AR-P17 PRINTER STATUS MONITOR/PRINTER MANAGEMENT UTILITY 8 - 1
(6) Job complete notification
When a print job is completed (or interrupted by an error), a notification
from the printer is received and displayed.
The dialog pop-up shows the notification.
1)
2)
1)
2)
3)
3)
4)
4)
5)
5)
6)
6)
7)
1) "Normal" icon
4) Printer driver name
2) Message
5) Job name
1) "Error" icon
5) Job name
6) "CLOSE" button
2) Message
6) "CLOSE" button
3) Notifying time
7) "DETAIL" button
3) Notifying time
4) Printer driver name
(7) Status advice immediately before printing (23-page machine/27-page machine)
If any trouble
occurs
The status is checked when printing is performed.
The dialog to select Continue or Cancel printing is
displayed.
AR-P17 PRINTER STATUS MONITOR/PRINTER MANAGEMENT UTILITY 8 - 2
2. Printer administration utility
(2) Alert/log function
• Alert by the pop-up/sound when the printer status changes.
A. Purpose
• Making of the alert/log file
This application provides easy and simple view of the following items:
• What kinds of network printers are connected in the network?
• Are the network printers operating normally?
• What functions does the printer have?
B. Operating environment
Windows 95, Windows 98, Windows Me, Windows NT4.0 Workstation
(SP3 or later)/2000 Professional, Windows XP Home Edition Professional TCP/IP, Winsock2 necessary
C. Outline of functions
(1) Network printer retrieval/list display
• Retrieval and list display of the network printers which conform to the
Printer MIB (RFC1759) specifications.
• Printer status display by the color of the icon
– Normal state (No color)
On-line
– Warning state (Yellow)
Paper low, toner near empty, printer warning
– Error state (Red)
Paper empty, cover open, toner empty, paper jam, printer error,
Specified output tray full
• List display filter function
(3) Printer property display
• Device information
Model name, status, name, installing place, RAM size, max. print
speed, etc.
• Paper exit tray information
Tray name, number of trays, paper empty/presence of each tray,
paper exit method, printing sequence, etc.
• Paper feed tray information
Number of trays, tray name, paper empty/presence of each tray,
paper size etc,
• Print setup
Channel & PDL information, default PDL, paper direction, single/
duplex print information
• Resource information
Print quantity, toner status
• Summary information
Information on the system and network
• SHARP NIC information
NetWare setup, IP address, hardware address, etc.
D. Note
(1) Install and uninstall
For NT/2000/XP, the administrator authority is required.
(2) Status display when auto power shut off
• The various information when the printer is in the "Auto power shut
off" mode is information immediately before entering the "Auto
power shut off mode.
1)
2)
3)
1) Main window
List display of network printers.
The status of a printer is indicated by the color of the icon.
2) Printer property page
Detailed information (on the functions and status) of a printer is displayed.
3) Pop-up alert
The pop-up-alert can be displayed by the setup when the printer
status changes.
AR-P17 PRINTER STATUS MONITOR/PRINTER MANAGEMENT UTILITY 8 - 3
Printer property page (Select a printer from the list and double
click it to display this page.)
[Paper feed tab]
[Device tab]
1)
2)
3)
1)
4)
2)
Toner Low
Toner Empty
Offline
Paper Jam
Paper Empty
Printer Error
Cover Open
Printer Warning
5)
3)
6)
4)
7)
1) Paper feed tray for normal use:
If the driver does not specify any paper feed tray, the printer uses
this tray.
2) List of paper feed trays:
3) Description: = Tray name
4) Model name: (Not set in some models.)
Information on the
tray selected from
5) Paper size: Length x width (mm)
the list is
6) Paper kind: Name defined by ISO/IEC
displayed.
10175DPA
7) Max. paper capacity: AR-M230/M270
series detects the presence of paper only.
[Print setup tab]
Specified Output Tray
Full
1)
2)
1) Model
2) Name: Can be set.
3)
3) Installing place: Can be set.
4) Property:
RM size
Max. paper size
Max. print speed
Paper path
4)
[Paper exit tab]
1) Channel list: List of the effective channels
1)
2) Paper direction: If the driver does not specify the direction, the
printer uses this direction for normal use. (No change allowed for
some models.)
2)
3)
3) Default PDL: If the driver does not specify any PDL, the printer uses
this PDL for normal use. (No change allowed for some models.)
4)
5)
4) Single/Duplex print: If the driver does not specify single/duplex
print, the printer uses this print path for normal use. (No change
allowed for some models.)
[Resource type]
6)
7)
2)
1) Paper exit tray for normal use:
If the driver does not specify any paper exit tray, the printer uses
this tray. No change allowed for some models.
2) List of paper output trays:
3) Description: = Tray name
4) Model name: (Not set in some models.)
5) Paper exit method: Face-up or face-down
Information on the
tray selected from
6) Printing sequence: "First To Last" or "Last
the list is
To First"
displayed.
7) Max. paper capacity: The paper presence
is detected and displayed only when the job
separator is installed.
1)
1) Total Impressions: The quantity of printouts and outputs of copy
and FAX.
2) Toner status: OK or toner empty or toner low.
(Only toner empty or not is detected in some models.)
AR-P17 PRINTER STATUS MONITOR/PRINTER MANAGEMENT UTILITY 8 - 4
[Summary tab]
Setup
[Application]
1)
1) Network and device information:
Device information
– Descriptions, operating time, etc.
Network information
– TCP, IP, the number of send/receive packet of SNMP
[SHARP NIC tab]
1)
2)
3)
1) Setup: Used to set that the icon is minimized when booting or not,
and that the setup content is stored when terminating or not.
1)
2)
3)
2) Network printer retrieval interval: Used to set automatic retrieval of
a printer on the network.
The printers to be retrieved can be set with the "Printer retrieval
(TCP/IP)" tab.
The retrieval interval is 1min to 60min. The default is 3min.
3) State and alert revision interval:
Used to set automatic revision of the printer status.
The revision interval is 10sec to 90sec. The default is 30sec.
[Confirmation]
4)
1) NetWare setup: Setup of NetWare enable/disable
If set to enable, setup and display and changes are made on the
following items:
NDS mode or Bindery mode
NDS tree name, context name
Bindery server name
Print server name
Ethernet frame name
2) TCP/IP setup: TCP/IP address, sub-net mask, default gateway
3) Hardware address: Hardware address of the network card in the
target printer.
4) Link to the device Web page (Provided only the models which
have an assembly Web server.)
1)
1) Confirmation message: Used to set that the confirmation pop-up
menu is displayed when;
the device setup is changed.
the device is deleted,
the filter setup is deleted,
the log file is deleted,
the application is terminated.
AR-P17 PRINTER STATUS MONITOR/PRINTER MANAGEMENT UTILITY 8 - 5
[Printer retrieval (TCP/IP)]
1) 2)
3)
1) Printer retrieval on the local network:
When this box is checked, the local network address is obtained
from the IP address and the sub net mask of the PC where PAU is
installed, and a printer on the local network is retrieved.
3) Advanced retrieval dialog box
Used to set the printer retrieval on an external network.
To specify an external network to be retrieved, enter the network
address and the sub net mask of that network.
2) Retrieval by IP address:
A certain IP address can be obtained.
Only when this box is checked, the printers which have IP
addresses listed on the list can be retrieved.
System diagram
Manager
PAU
Printer status monitor
User
Printer status monitor
User
Printer status monitor
User
Printer status monitor
User
Printer
status
monitor
User
Printer status monitor
User
AR-P17 PRINTER STATUS MONITOR/PRINTER MANAGEMENT UTILITY 8 - 6
[9] TROUBLE CODE LIST
Trouble code
Main Sub
code code
F9
00
Details of trouble
Content
Details
Cause
Check
and
remedy
10
Content
Details
Cause
Check
and
remedy
80
Content
Details
Cause
Check
and
remedy
81
Trouble code
Main Sub
code code
F9
82
Content
Details
Cause
Check
and
remedy
MCU-PRT communication trouble
Communication establishment error/
framing/parity/protocol error
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB trouble
Communication trouble between MCU and
printer PWB
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Protocol)
Communication trouble between MCU and
printer PWB (Protocol error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Parity)
Communication trouble between MCU and
printer PWB (Parity error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Details of trouble
Content
Details
Cause
Check
and
remedy
84
Content
Details
Cause
Check
and
remedy
88
Content
Details
Cause
Check
and
remedy
99
AR-P17 TROUBLE CODE LIST 9 - 1
Content
Details
Cause
Check
and
remedy
Printer PWB communication trouble
(Overrun)
Communication trouble between MCU and
printer PWB (Overrun error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Framing)
Communication trouble between MCU and
printer PWB (Framing error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Timeout)
Communication trouble between MCU and
printer PWB (Timeout error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Machine-PCL board language error
The machine language setup does not
coincide with the PCL board language
setup.
PCL board connection error
SIM setup error
Check the firmware of the PCL board and
the combination of the panel screen data,
and download the correct version, if
necessary.
Check the machine language information.
(Machine language setup: SIM 26-22)
[10] ELECTRICAL SECTION
PCI connector
1. Block diagram
TMPR4927
ADDR[19:0]
PCI BUS 32bit/33MHz
SDRAM
64MB
DATA
[31:0]
DATA[63:0]
DATA
[63:0]
PIO
SDRAM-DIMM
128MB or 256MB
RJ45
SPD
PIO
DP83816
(MAC/PHY)
EEPROM
256Kb
Flash DIMM
12MB
DATA[31:0]
Flash-DIMM
8MB(Option)
DATA[31:0]
Driver
DATA[31:0]
UART1
(Japan Only)
For Debug
IO ASIC(Unicorn2)
UART0
Connector
M-BUS
Driver
DATA[15:0]
Connector
Energy-saving I/F correspondence
USB2.0(FS)
ML60852A
System
Bus I/F
1284
Cont.
Image
Cont.
RTC
I/F
IO I/F
PIO
USB2.0 (Full speed mode correspondence)
AR-P17 ELECTRICAL SECTION 10 - 1
1284
Driver
Connector
Connector
MROM-DIMM
32MB(PS Font)
q
PARTS GUIDE
CODE:00ZARP17//P1/
プリンタ コントローラー
PRINT CONTROLLER
MODEL
AR-P17
このパーツガイドに掲載されている表示価格ランクは消費税抜きです。
CONTENTS
1 梱包&付属品 (Packing material & Accessories)
2 PCL PWB UNIT(PCL PWB UNIT)
■
索引 (Index)
本書はサービス活動用に作成した資料です。
一部内容が製品の改良・改善等により予告
なしに変わることがあります。
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
補修部品のランク付
市場における補修部品の在庫管理が、適正に運営出来る手助けとなることを、目的とします。
Aランク : メンテナンスパーツ、メンテナンスパーツには入っていないがメンテナンスパーツに近い消耗パーツ。
Bランク : 性能・機能パーツ(センサー、クラッチ等の電気パーツ)
、消耗パーツ。
Eランク : 基板含むユニットパーツ。
Dランク : 整備パーツ(外装、パッキング、同梱パーツ)。
Cランク : 上記ランク以外のパーツ(基板の子部品を除いたもの)
。
DEFINITION
Rank
Rank
Rank
Rank
Rank
A
B
E
D
C
:
:
:
:
:
Maintenance parts, and consumable parts which are not included in but closely related to maintenance parts
Performance/function parts (sensors, clutches, and other electrical parts), consumable parts
Unit parts including PWB
Preparation parts (External fitting, packing, parts packed together)
Parts other than the above (excluding sub components of PWB)
安全性・信頼性確保のため部品は、必ず正規のものをご使用下さい。
! 印の商品は、安全上重要な部品です。交換をする時は、安全及び性能維持のため必ず指定の部品をご使用下さい。
Because parts marked with "!" is indispensable for the machine safety maintenance and operation, it must be replaced with
the parts specific to the product specification.
F
F
F
F
当モデルのサービス資料には、この資料以外にサービスマニュアル ( 回路図含む ) があります。合わせてご利用下さい。
Other than this Parts Guide, please refer to documents Service Manual(including Circuit Diagram)of this model.
Please use the 13 digit code described in the right hand corner of front cover of the document, when you place an order.
For U.S. only-Use order codes provided in advertising literature. Do not order from parts department.
1 梱包&付属品 (Packing material & Accessories)
NO.
PARTS CODE
1 CDSKA0033QS31
4 SPAKA399ACCZZ
6 TCADZ0288QSZZ
TINSJ1076QSZZ
TINSE1077QSZZ
7
TINSF1078QSZZ
TINSS1079QSZZ
9 LX-BZ0024QSZZ
10 SSAKA0006UCZZ
11 XBPSD30P06KS0
101 LSUPM0002QSZZ
102 VHI29L12802QS
PRICE RANK
Ex.
Ja.
BA
FX
AB
DD
AD
DJ
AQ
EQ
AP
EQ
AS
EQ
AS
EQ
AA
DD
AA
DD
AA
DD
AE
DJ
BQ
LP
NEW
MARK
N
N
N
N
N
N
N
N
PART
RANK
D
D
D
D
D
D
D
C
D
C
C
B
DESCRIPTION
CD ROM J
Vinyl bag
Inst.manual
OPE.manual
OPE.manual
OPE.manual
OPE.manual
Screw(3×8)
Vinyl bag(50×60mm)
Screw(3×6KS)
Support post
PRG DIMM
–1–
[Japan] CD ROM J
ポリ袋
[Except USA,Canada,LAG] 設置手順書
[Japan] 取扱説明書
[ENGLISH] 取扱説明書
[FRENCH] 取扱説明書
[SPANISH] 取扱説明書
ビス
ポリ袋
ビス
サポートポスト 7
[Japan] PRG DIMM
1 梱包&付属品 (Packing material & Accessories)
10
9
4
11
2
3
1
5
7
6
PRP01669
2 PCL PWB UNIT(PCL PWB UNIT)
NO.
1
3
4
5
6
9
11
12
13
14
15
16
18
19
20
21
22
25
26
28
29
30
32
33
34
35
36
37
PARTS CODE
QCNCM0041QSZZ
QCNCW0025QSZZ
QCNCW0071GCZZ
QCNCW7045XCZZ
QSOCN0010QSZZ
QSOCZ0079FCZZ
RCILZ0353AFZZ
RCORF1013ACZZ
RCORF1057ACZZ
RCRUA0019QSZZ
RCRUA0020QSZZ
RFILN0010QSZZ
RH-IX1013ACZZ
RMPTR4103ACZZ
RMPTR4103ACZZ
RMPTR4330ACZZ
RMPTR4330ACZZ
RMPTR4330ACZZ
RMPTR4330ACZZ
RMPTR4472ACZZ
RMPTR4560ACZZ
VCCCCZ1HH100D
VCCCCZ1HH101J
VCCCCZ1HH680J
VCCUCY1AJ105Z
VCEAPH1CC106M
VCEAPS1CC226M
VCEAPZ1CW107M
VCEAPZ1CW477M
VCKYCZ1AB683K
VCKYCZ1CB103K
VCKYCZ1CB103K
VCKYCZ1CF104Z
PRICE RANK
Ex.
Ja.
AP
EQ
AL
EB
AH
DX
AG
DS
AV
FG
AN
EQ
AH
DX
AD
DJ
AB
DJ
AR
EQ
AL
EB
AB
DD
BK
HC
AB
DD
AB
DD
AB
DD
AB
DD
AB
DD
AB
DD
AB
DD
AA
DD
AA
DD
AA
DD
AA
DD
AC
DD
AC
DD
AC
DJ
AD
DJ
AE
DS
AB
DD
AA
DD
AA
DD
AB
DD
NEW
MARK
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
B
B
C
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Connector(TX25-100P12)
Connector(TX24-60R-12)
Connector(57pin)
Connector(USB)
Socket(RJ-45)
Socket(100pin)
Chock coil(PLP3216S121SL2)
Core(BLM41P600S)
Ferrite beads(BLM21P221SG)
Crystal(25.00M OSC)
Crystal(12.00M OSC)
Noise filtet(BLM18BB121SN1D)
IC(SDRAM 256M)
Block resistor(10KΩ×4)
Block resistor(10KΩ×4)
Block resistor(33Ω×4)
Block resistor(33Ω×4)
Block resistor(33Ω×4)
Block resistor(33Ω×4)
Block resistor(4.7KΩ×4)
Block resistor(56Ω×4)
Capacitor(50WV 10pF)
Capacitor(50WV 100pF)
Capacitor(50WV 68pF)
Capacitor(10WV 1.0µF)
Capacitor(16WV 10µF)
Capacitor(16WV 22µF)
Capacitor(16WV 100µF)
Capacitor(16WV 470µF)
Capacitor(10WV 68µF)
Capacitor(16WV 0.010µF)
Capacitor(16WV 0.010µF)
Capacitor(16WV 0.10µF)
–2–
[CN3]
[CN9]
[CN11]
[CN10]
[CN12]
[Japan][CN8]
[L1]
[L10∼13]
[L2]
[X1]
[X2]
[L3∼6,14,15]
[IC5,6]
[RN27,41,44,49,51]
[RN54,56,58,60]
[RN1,2,6,8,20,22,23,25,26]
[RN28∼40,42,43,45∼48]
[RN50,52,53,55,57,59]
[RN65,66,67,68,71∼76]
[RN24,61∼64,69,70]
[RN3,4,5,7,9∼19,21]
[C91]
[C61∼67,72∼88]
[C3,209,210]
[C96]
[C113,145,146]
[C39,90,114]
[C4]
[C46,47]
[C147,150]
[C97∼105,108,110,112]
[C118,120,205,215]
[C1,2,6∼38,40,42∼45]
コネクター
コネクター
コネクター
コネクター
ソケツト
ソケツト
チョークコイル
コア
フェライトビーズ
クリスタル
クリスタル
ノイズフイルタ IC
ブロックテイコウ
ブロックテイコウ
ブロックテイコウ
ブロックテイコウ
ブロックテイコウ
ブロックテイコウ
ブロックテイコウ
ブロックテイコウ
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
2 PCL PWB UNIT(PCL PWB UNIT)
NO.
37
38
39
40
44
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
PARTS CODE
VCKYCZ1CF104Z
VCKYCZ1CF104Z
VCKYCZ1CF104Z
VCKYCZ1CF104Z
VCKYCZ1HB102K
VHDD1FM3+++-1
VHIDP83816+-1
VHIPST598IN-1
VHI24WC256K-1
VHI60852ATB-1
VHI74LCX08FT1
VHI74LCX14FT1
VHI74LCX244FT
VHI74LCX245FT
VHI74LVX16128
VHI93C46VI+-1
VHPLT1P67A+-1
VHVICPS1.2/-1
VRS-CZ1JD000J
VRS-CZ1JD000J
VRS-CZ1JD000J
VRS-CZ1JD100J
VRS-CZ1JD100J
VRS-CZ1JD100J
VRS-CZ1JD102J
VRS-CZ1JD102J
VRS-CZ1JD103J
VRS-CZ1JD103J
VRS-CZ1JD103J
VRS-CZ1JD103J
VRS-CZ1JD121J
VRS-CZ1JD152J
VRS-CZ1JD153J
VRS-CZ1JD220J
VRS-CZ1JD221J
VRS-CZ1JD302J
VRS-CZ1JD330J
VRS-CZ1JD330J
VRS-CZ1JD330J
VRS-CZ1JD330J
VRS-CZ1JD330J
VRS-CZ1JD470J
VRS-CZ1JD471J
VRS-CZ1JD472J
VRS-CZ1JD472J
VRS-CZ1JD472J
VRS-CZ1JD472J
VRS-CZ1JD560J
VRS-CZ1JD822J
VRS-TS2AD220J
VRS-TX2HDR24J
VRSCY1JR49R9F
VRSCY1JR54R9F
VSDTC114YK/-1
PRICE RANK
Ex.
Ja.
AB
DD
AB
DD
AB
DD
AB
DD
AA
DD
AD
DJ
BE
GN
AF
DS
AV
FG
AX
FG
AF
DS
AF
DS
AH
DX
AH
DX
AP
EQ
AE
DS
AC
DJ
AF
DS
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AA
DD
AC
ZZ
NEW
MARK
N
N
PART
RANK
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
DESCRIPTION
Capacitor(16WV 0.10µF)
Capacitor(16WV 0.10µF)
Capacitor(16WV 0.10µF)
Capacitor(16WV 0.10µF)
Capacitor(50WV 1000pF)
Diode(DIFM3)
IC(DP83816)
IC(PST598IN)
EEPROM(24WC256K)
IC(60852ATB)
IC(74LCX08FT1)
IC(74LCX14FT1)
IC(TC74LCX244)
IC(74LCX245FT)
IC(74LVX16128)
IC(93C46VI)
Diode(LT1P67A)
IC protecrot(ICPS1.2)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 10Ω ±5%)
Resistor(1/16W 10Ω ±5%)
Resistor(1/16W 10Ω ±5%)
Resistor(1/16W 1.0KΩ ±5%)
Resistor(1/16W 1.0KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 120Ω ±5%)
Resistor(1/16W 1.5KΩ ±5%)
Resistor(1/16W 15KΩ ±5%)
Resistor(1/16W 22Ω ±5%)
Resistor(1/16W 220Ω ±5%)
Resistor(1/16W 300KΩ ±5%)
Resistor(1/16W 33Ω ±5%)
Resistor(1/16W 33Ω ±5%)
Resistor(1/16W 33Ω ±5%)
Resistor(1/16W 33Ω ±5%)
Resistor(1/16W 33Ω ±5%)
Resistor(1/16W 47Ω ±5%)
Resistor(1/16W 470Ω ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 56Ω ±5%)
Resistor(1/16W 8.2KΩ ±5%)
Resistor(1/10W 22Ω ±5%)
Resistor(1/2W 0.24Ω ±5%)
Resistor(1/10W 49.9Ω ±5%)
Resistor(1/10W 54.9Ω ±5%)
Transistor(DTC114YK)
–3–
[C48∼53,68∼71,89]
[C92∼95,115∼117,119]
[C121,124∼140,143,144]
[C152∼204,206,208,214]
[C106,107,109,111,148,149]
[D2]
[IC24]
[IC31]
[IC3]
[IC21]
[IC2]
[IC4]
[IC8,10,12,15,20,30]
[IC7,9,11,13,18,19]
[IC22]
[IC26]
[D1]
[F1]
[R85∼92,165∼176]
[R180∼184,189,197,209]
[R213,214,248,255∼257]
[R94,136∼150,187,205,219]
[R220,223∼226,229∼232]
[R245,267∼274]
[R2∼6,18,32,34∼37]
[R156,157,247]
[R17,19,26,29,30,31,38,39,95]
[R99,110∼113,118,120,121]
[R158,159,178,179,185,186]
[R204,206,210,263,264,291]
[R100]
[R160]
[R228]
[R24]
[R154]
[R227]
[R9,10,13∼16,20∼23,25,42]
[R43,45,46,50,51,53,55,56]
[R57,59,60∼66,93,102∼109]
[R114∼117,119,258,260∼262]
[R265,266,275∼287]
[R44,47,48,49,243]
[R188,198]
[R40,41,52,69,70]
[R74∼76,101,123,124]
[R151,152,155,161]
[R217,221,246,249]
[R54,96,97,98]
[R27,28,77∼84]
[R162,163,164]
[R222]
[R190,200]
[R193,202]
[TR1]
コンデンサー
コンデンサー
コンデンサー
コンデンサー
コンデンサー
ダイオード
IC
IC
EEPROM
IC
IC
IC
IC
IC
IC
IC
ダイオード
IC プロテクター
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
テイコウ
トランジスター
■
索引 (Index)
PARTS CODE
[C]
CDSKA0033QS31
[L]
LSUPM0002QSZZ
LX-BZ0024QSZZ
[Q]
QCNCM0041QSZZ
QCNCW0025QSZZ
QCNCW0071GCZZ
QCNCW7045XCZZ
QSOCN0010QSZZ
QSOCZ0079FCZZ
[R]
RCILZ0353AFZZ
RCORF1013ACZZ
RCORF1057ACZZ
RCRUA0019QSZZ
RCRUA0020QSZZ
RFILN0010QSZZ
RH-IX1013ACZZ
RMPTR4103ACZZ
RMPTR4330ACZZ
RMPTR4472ACZZ
RMPTR4560ACZZ
[S]
SPAKA399ACCZZ
SSAKA0006UCZZ
[T]
TCADZ0288QSZZ
TINSE1077QSZZ
TINSF1078QSZZ
TINSJ1076QSZZ
TINSS1079QSZZ
[V]
VCCCCZ1HH100D
VCCCCZ1HH101J
VCCCCZ1HH680J
VCCUCY1AJ105Z
VCEAPH1CC106M
VCEAPS1CC226M
VCEAPZ1CW107M
VCEAPZ1CW477M
VCKYCZ1AB683K
VCKYCZ1CB103K
VCKYCZ1CF104Z
VCKYCZ1HB102K
VHDD1FM3+++-1
VHI24WC256K-1
VHI29L12802QS
VHI60852ATB-1
VHI74LCX08FT1
VHI74LCX14FT1
VHI74LCX244FT
VHI74LCX245FT
VHI74LVX16128
VHI93C46VI+-1
VHIDP83816+-1
VHIPST598IN-1
VHPLT1P67A+-1
VHVICPS1.2/-1
VRSCY1JR49R9F
VRSCY1JR54R9F
VRS-CZ1JD000J
VRS-CZ1JD100J
VRS-CZ1JD102J
VRS-CZ1JD103J
VRS-CZ1JD121J
VRS-CZ1JD152J
VRS-CZ1JD153J
VRS-CZ1JD220J
VRS-CZ1JD221J
VRS-CZ1JD302J
VRS-CZ1JD330J
VRS-CZ1JD470J
VRS-CZ1JD471J
VRS-CZ1JD472J
VRS-CZ1JD560J
VRS-CZ1JD822J
VRS-TS2AD220J
PARTS CODE
PRICE R.
NEW P/R
Ex. Ja.
JAPAN ONLY
ORDER CODE
NO.
578 966 0138
1-
1
BA
FX
N
D
578 233 0027
578 970 0222
1- 101
1- 9
AE
AA
DJ
DD
N
C
C
578 510 0271
578 510 0243
578 510 0211
578 510 0250
578 527 0033
578 527 0029
222222-
1
3
4
5
6
9
AP
AL
AH
AG
AV
AN
EQ
EB
DX
DS
FG
EQ
596 614 0565
596 615 0063
596 615 0149
578 616 0072
578 616 0073
578 621 0076
596 573 4270
567 631 0100
567 631 0109
567 631 0102
596 631 0499
22222222222-
11
12
13
14
15
16
18
19
20
21
22
AH
AD
AB
AR
AL
AB
BK
AB
AB
AB
AA
DX
DJ
DJ
EQ
EB
DD
HC
DD
DD
DD
DD
505 902 5004
541 906 1016
1- 4
1- 10
AB
AA
DD
DD
572 913 1007
578 916 0817
578 916 0818
578 916 0833
578 916 0819
11111-
6
7
7
7
7
AD
AP
AS
AQ
AS
DJ
EQ
EQ
EQ
EQ
521 593 0027
521 593 0028
567 593 0316
596 593 0899
521 594 0001
593 594 0584
567 594 0133
575 594 0013
572 593 0354
595 593 1450
521 593 0017
521 593 0030
523 570 0014
578 573 1200
578 573 1359
572 573 2910
521 573 0491
572 573 2024
521 573 0388
594 573 1659
578 573 1048
578 573 1358
567 573 1648
523 573 0081
578 574 0048
567 577 0014
567 581 0630
596 581 3342
521 581 0082
567 581 0524
521 581 0093
521 581 0085
567 581 0526
521 581 0175
567 581 0528
567 581 0532
567 581 0533
572 581 2072
521 581 0202
521 581 0170
567 581 0617
521 581 0088
572 581 2084
572 581 2066
500 581 5044
2- 25
2- 26
2- 28
2- 29
2- 30
2- 32
2- 33
2- 34
2- 35
2- 36
2- 37
2- 38
2- 39
2- 46
1- 102
2- 47
2- 48
2- 49
2- 50
2- 51
2- 52
2- 53
2- 40
2- 44
2- 54
2- 55
2- 74
2- 75
2- 56
2- 57
2- 58
2- 59
2- 60
2- 61
2- 62
2- 63
2- 64
2- 65
2- 66
2- 67
2- 68
2- 69
2- 70
2- 71
2- 72
AA
AA
AA
AC
AC
AC
AD
AE
AB
AA
AB
AA
AD
AV
BQ
AX
AF
AF
AH
AH
AP
AE
BE
AF
AC
AF
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
DD
DD
DD
DD
DD
DJ
DJ
DS
DD
DD
DD
DD
DJ
FG
LP
FG
DS
DS
DX
DX
EQ
DS
GN
DS
DJ
DS
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
N
N
N
C
C
C
C
C
C
C
C
C
B
B
C
B
B
B
B
B
D
D
N
N
N
N
N
N
N
D
D
D
D
D
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
–4–
VRS-TX2HDR24J
VSDTC114YK/-1
[X]
XBPSD30P06KS0
JAPAN ONLY
ORDER CODE
NO.
PRICE R.
NEW P/R
Ex. Ja.
578 581 0720
507 576 5005
2- 73
2- 76
AA
AC
DD
ZZ
541 970 0016
1- 11
AA
DD
N
C
B
C
LEAD-FREE SOLDER
CAUTION FOR BATTERY REPLACEMENT
The PWB’s of this model employs lead-free solder. The “LF” marks
indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.
Example:
Lead-Free
5mm
(Danish)
ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to manufacturer’s instructions.
Solder composition
code (Refer to the
table at the right.)
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
a
z
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
Sn-In-Ag-Bi
i
(Swedish)
Sn-Cu-Ni
n
Sn-Ag-Sb
s
Bi-Sn-Ag-P
Bi-Sn-Ag
p
<Solder composition code of lead-free solder>
Solder composition
Solder composition code
Sn-Ag-Cu
a
Sn-Ag-Bi
Sn-Ag-Bi-Cu
b
Sn-Zn-Bi
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher
than that of conventional lead solder thread, the use of the exclusiveuse soldering iron is recommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is
about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB
when completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip
may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted
together with lead-free solder. To avoid this, clean the soldering iron tip
after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean
and file the tip with steel wool or a fine filer.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
CAUTION FOR BATTERY DISPOSAL
(For USA, CANADA)
"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY
(MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY
THAT MUST BE DISPOSED OF PROPERLY. REMOVE THE
BATTERY FROM THE PRODUCT AND CONTACT YOUR
LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION
ON RECYCLING AND DISPOSAL OPTIONS.
"TRAITEMENT DES PILES USAGÉES"
CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE
MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANÈSE)
QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LA
PILE DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE
AGENCE ENVIRONNEMENTALE LOCALE POUR DES
INFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET
DE TRAITEMENT.
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.
Trademark Acknowledgments
Microsoft Windows, MS-DOS, Windows NT, Windows 2000 are trademarks of Microsoft
Corporation in the U. S. A. and other countries.
Macintosh, Power Macintosh, Mac OS, LaserWriter, and AppleTalk are registered trademarks of
Apple Computer, Inc.
IBM, PC/ AT, and PowerPC are trademarks of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation.
PCL is a trademark of the Hewlett- Packard Company.
PostScript is a registered trademark of Adobe Systems Incorporated.
NetWare is a registered trademark of Novell, Inc.
All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Digital Document System Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2003 August Printed in Japan