00cv_YSP-40D_B.fm Page 1 Wednesday, October 17, 2007 8:31 AM
B
YSP-40D
YSP-40D
Digital Sound ProjectorTM
© 2007
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WK94330
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
Caution: Read this before operating this unit.
1
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2
Install this sound system in a well ventilated, cool, dry, clean place with
at least 5 cm (2 in) of space above (or below) this unit – away from
direct sunlight, heat sources, vibration, dust, moisture, and/or cold.
3
Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
4
Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid may
cause electrical shock to the user and/or damage to this unit.
6
Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
7
Do not plug in this unit to a wall outlet until all connections are
complete.
8
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power supply cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. Yamaha will not
be held responsible for any damage resulting from use of this unit
with a voltage other than specified.
13 To prevent damage by lightning, keep the power supply cable
disconnected from a wall outlet or this unit during a lightning
storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed.
The cabinet should never be opened for any reasons.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
WARNING
THE POWER SUPPLY CABLE OF THIS UNIT MUST BE
CONNECTED TO THE MAIN SOCKET OUTLET VIA A
PROTECTIVE EARTHING CONNECTION.
This unit is not disconnected from the AC power source as long as
it is connected to the AC wall outlet, even if this unit itself is
turned off by STANDBY/ON. This state is called the standby
mode. In this state, this unit is designed to consume a very small
quantity of power.
FOR U.K. CUSTOMERS
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3-pin plug fitted. For details, refer to the instructions
described below.
Note
The plug severed from the mains lead must be destroyed, as a plug with
a bared flexible cord is hazardous if engaged in a live socket outlet.
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN-AND-YELLOW:
EARTH
BLUE:
NEUTRAL
BROWN:
LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be
connected to the terminal in the plug which is marked by the letter
“E” or the safety earth symbol or coloured GREEN or GREENAND-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal marked with the letter “N” or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal marked with the letter “L” or coloured RED.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
15 When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the power supply cable from the wall
outlet.
16 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
17 Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the power supply cable from the
wall outlet.
This symbol mark is according to the
EU directive 2002/96/EC.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power supply cable from the
outlet, then leave the unit alone.
19 When using the unit for a long time, the unit may become warm.
Turn the power off, then leave the unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug
can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
i En
This symbol mark means that electrical
and electronic equipment, at their endof-life, should be disposed of separately
from your household waste.
Please act according to your local rules
and do not dispose of your old products
with your normal household waste.
Contents
Overview ................................................................. 2
Features .................................................................. 3
Using this manual .................................................. 5
Supplied accessories .............................................. 6
Controls and functions .......................................... 7
PREPARATION
Installation ............................................................ 14
Before installing this unit ........................................ 14
Installing this unit ................................................... 14
Connections .......................................................... 17
Getting started ..................................................... 29
Installing batteries in the remote control ................ 29
Operation range of the remote control .................... 29
Turning on this unit or setting it to the
standby mode ...................................................... 30
Using SET MENU ................................................ 31
Changing OSD language ..................................... 33
AUTO SETUP (IntelliBeam) .............................. 34
The flow chart of AUTO SETUP ........................... 34
Installing the IntelliBeam microphone ................... 35
Using AUTO SETUP (IntelliBeam) ....................... 36
Using the system memory ................................... 41
Enjoying stereo sound ..........................................66
2-channel stereo playback ....................................... 66
5-channel stereo playback ....................................... 66
Playing back sound clearly (My Beam) ..............67
Using auto-adjust function ...................................... 67
Using manual-adjust function ................................. 68
Using sound field programs .................................69
CINEMA DSP programs ........................................ 71
Using the music enhancer ....................................74
Using the volume mode (Night listening
enhancer/TV volume equal mode) ..................75
Using the sleep timer ............................................76
Displaying the input source information ............78
Using the HDMI control feature .........................79
ADVANCED OPERATION
MANUAL SETUP ................................................80
Using MANUAL SETUP ....................................... 81
BEAM MENU ........................................................ 82
SOUND MENU ...................................................... 86
INPUT MENU ........................................................ 88
DISPLAY MENU ................................................... 92
Adjusting the audio balance ................................94
Using the test tone .................................................. 94
Using the audio output being played back .............. 95
Selecting the input mode ......................................97
Adjusting the system parameters .......................98
Using the system parameters .................................. 98
Setting the MEMORY PROTECT ......................... 99
Setting the MAX VOLUME ................................. 100
Setting the TURN ON VOLUME ........................ 100
Setting the MONITOR CHECK ........................... 101
Setting the DEMO MODE ................................... 102
Setting the PANEL INPUT KEY ......................... 103
Disabling the front panel keys .............................. 104
Setting the FACTORY PRESET .......................... 105
Remote control features .....................................107
BASIC OPERATION
Playback ............................................................... 44
Selecting the input source ....................................... 44
Playing back sources ............................................... 45
Adjusting the volume .............................................. 46
DAB (Digital Audio Broadcasting) .................... 47
ADDITIONAL INFORMATION
Troubleshooting ..................................................113
Glossary ...............................................................117
DAB frequency table ..........................................119
Index ....................................................................120
Specifications ......................................................121
List of remote control codes ...........................................i
1 En
English
About DAB ............................................................. 47
Preparing the DAB tuning ...................................... 48
DAB tuning ............................................................. 49
PRESET MEMORY ............................................... 50
DAB service information ........................................ 52
Accessing DAB MENU .......................................... 53
INIT SCAN ............................................................. 53
Setting remote control codes ................................ 107
Controlling other components .............................. 108
Using the TV macro ............................................. 111
ADDITIONAL
INFORMATION
Convenient usage of the system memory ............... 41
Saving settings ........................................................ 41
Loading settings ...................................................... 42
5 Beam .................................................................... 60
Stereo plus 3 Beam ................................................. 61
3 Beam .................................................................... 61
My Surround ........................................................... 61
Enjoying 2-channel sources in surround sound ...... 63
Enjoying TV in surround sound ............................. 64
Adjusting surround mode parameters ..................... 65
ADVANCED
OPERATION
Displaying the OSD (on-screen display) ................ 31
The flow chart of SET MENU ................................ 32
Enjoying surround sound ....................................60
BASIC
OPERATION
SETUP
Connection .............................................................. 57
Controlling iPod™ .................................................. 57
SETUP
Before connecting components ............................... 18
Connections using HDMI cables ............................ 19
Connecting a TV ..................................................... 20
Connecting a DVD player/recorder ........................ 21
Connecting a digital satellite tuner or a cable
TV tuner ............................................................. 22
Connecting a digital airwave tuner ......................... 23
Connecting a portable audio player ........................ 24
Connecting other external components .................. 25
Connecting a subwoofer ......................................... 26
Connecting the DAB antenna ................................. 27
About the RS-232C/IR-OUT/IR IN terminals ........ 27
Connecting the AC power supply cable ................. 28
Using iPod™ .........................................................57
PREPARATION
Front panel ................................................................ 7
Front panel display ................................................... 8
Rear panel ................................................................. 9
Remote control ........................................................ 11
TUNE AID ............................................................. 54
DRC MODE ........................................................... 55
PRUNE LIST .......................................................... 56
PRESET DELETE .................................................. 56
INTRODUCTION
INTRODUCTION
Overview
Overview
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of
wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of
surround sound experience as your local movie theater.
Yamaha YSP-40D Digital Sound Projector challenges this preconception that complicated speaker setup and
troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is
not only easy to set up, but is also capable of reproducing the kind of powerful surround sound you have been waiting for
from its built-in 2 woofers and 40 full-range small speakers.
You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly
directional sound that comes in on the listening position from all directions.
The YSP-40D projects sound beams containing surround sound information for the front right (R), front left (L),
surround right (SR), and surround left (SL) speaker positions, which are reflected off the walls of your listening room
before reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector
creates true-to-life 5.1-channel surround sound that makes you feel as if there are actual speakers around the room.
Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.
Imaginary
front right
speaker
R
C
SR
L
SL
Imaginary
surround right
speaker
Imaginary
front left
speaker
Imaginary
center
speaker
Listening position
Imaginary
surround left
speaker
2 En
Features
Features
My Surround
In addition to the above mentioned beam modes, this unit
is equipped with My Surround beam mode that allows you
to enjoy surround system even in a small listening area.
My Beam
This unit employs My Beam that ensures a clear sound in
a noisy environment. You can adjust the beam angle
manually or automatically using the supplied remote
control to the maximum of 45°, rightward and leftward.
Cinema DSP
This unit employs the Cinema DSP technology developed
by Yamaha Electronics Corp. that lets you experience
movies at home with all the original dramatic sound
impact.
HDMI™ (High-Definition Multimedia Interface)
◆ HDMI interface for standard, enhanced, or high-definition
video (including 1080p video signal transmission) as well as
multi-channel digital audio based on HDCP
◆ Simple and easy connections with HDMI supported external
components
◆ Functional link with an HDMI control-compatible TV
◆ Analog video up-scaling from 480i (NTSC)/576i (PAL) or
480p (NTSC)/576p (PAL) to 720p or 1080i
Versatile Remote Control
The supplied remote control comes with preset remote
control codes used to control the DVD player, VCR, cable
TV tuner, and digital satellite tuner connected to this unit.
In addition, the remote control is equipped with the macro
capability that enables a series of operations with the press
of a single button.
Compatibility with the Newest Technologies
This unit employs decoders compatible with Dolby
Digital, DTS, Dolby Pro Logic, Dolby Pro Logic II, DTS
Neo:6, and Music Enhancer.
◆ Dolby Digital
This is the standard audio signal format used on various
digital media such as DVD, Blu-Ray, and HD DVD. This
surround technology delivers high-quality digital audio for up
to 5.1 discrete channels to produce a directional and more
realistic effect.
◆ DTS
This is the standard audio signal format used on various
digital media such as DVD, Blu-Ray, and HD DVD. This
surround technology delivers high-quality digital audio for up
to 5.1 discrete channels to produce a directional and more
realistic effect.
◆ Dolby Pro Logic
This sophisticated, matrix decoding technology up-converts
any 2-channel source audio to a 5.1-channel full bandwidth
playback, resulting in a surround sound experience.
◆ Dolby Pro Logic II
This is a redesigned version of Dolby Pro Logic that employs
2 stereo surround channels, a subwoofer, and a greatly
enhanced steering logic. This improved technology provides
an exceptionally stable sound field that simulates 5.1 to a
much greater degree than the original Dolby Pro Logic.
◆ DTS Neo:6
This technology decodes the conventional 2-channel sources
for 6-channel playback, enabling playback with the full-range
channels with higher separation. Music mode and Cinema
mode are available to play back music and movie sources
respectively.
◆ Music Enhancer to improve the sound quality of compression
artifacts such as the MP3 format.
INTRODUCTION
Digital Sound Projector™
The Digital Sound Projector technology allows one slim
unit to control and steer multiple channels of sound to
generate multi-channel surround sound, thus eliminates
the need for satellite loudspeakers and cabling normally
associated with conventional surround sound systems.
This unit also employs the beam modes that let you enjoy
the surround sound (5 Beam, Stereo plus 3 Beam, 3 Beam,
and My Surround), 2-channel and 5-channel stereo
playback, and My Beam.
DAB (Digital Audio Broadcasting) Tuning
Capability
◆ DLS (Dynamic Label Segment) information display
◆ INIT SCAN that locates all DAB services in your area
◆ TUNE AID that optimizes DAB reception
iPod™ Controlling Capability
◆ DOCK terminal to connect a Yamaha iPod universal dock
(such as the YDS-10, sold separately), which supports iPod
(Click and Wheel), iPod nano, and iPod mini
◆ Playback information displaying capability
◆ Battery charging capability
AUTO SETUP (IntelliBeam)
This unit employs the automatic sound beam and acoustic
optimization technology with the aid of the supplied
IntelliBeam microphone. You can avoid troublesome
listening-based speaker setup and achieve highly accurate
sound beam adjustments that best match your listening
environment.
English
3 En
Features
The “
” logo and “IntelliBeam” are trademarks of
YAMAHA Corporation.
Manufactured under license from 1 Ltd. Worldwide patents
applied for.
The “
The “
” logo and “Cinema DSP” are registered
trademarks of YAMAHA Corporation.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
” logo and “Digital Sound Projector™” are trademarks
of 1 Ltd.
TruBass, SRS and the “
” symbol are registered trademarks
of SRS Labs, Inc. TruBass technology is incorporated under
license from SRS Labs, Inc.
™
“DTS” and “Neo:6” are registered trademarks of DTS, Inc.
is a trademark of DiMAGIC Co., Ltd.
iPodTM
“iPod” is a trademark of Apple Inc., registered in the U.S. and
other countries.
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of HDMI
Licensing LLC.
The “DAB Digital Radio” logo and the stylised “r” mark ® and ©
Digital One Limited.
4 En
Using this manual
Using this manual
1
Install this unit in your listening room.
See “Installation” on page 14.
2
Connect this unit to your TV and other external components.
See “Connections” on page 17.
3
Prepare the remote control and turn on the power of this unit.
See “Getting started” on page 29.
4
Run AUTO SETUP.
See “AUTO SETUP (IntelliBeam)” on page 34.
5
Play back a source.
See “Playback” on page 44.
6
Change the beam modes and/or CINEMA DSP settings.
See “Enjoying surround sound” on page 60.
INTRODUCTION
Notes
• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the
supplied owner’s manual for each component.
• Operations in this manual use keys on the supplied remote control of this unit unless otherwise specified.
• y indicates a tip for your operation.
• This manual is printed prior to production. Designs and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
If you want to make additional settings
and adjustments
English
7
Run MANUAL SETUP to fine-tune settings and/or set remote control codes.
See “MANUAL SETUP” on page 80 and “Remote control features” on page 107.
5 En
Supplied accessories
Supplied accessories
Check that you have received all of the following parts.
Remote control (×1)
STANDBY/ON
Fasteners (×4)
Optical cable (×1)
POWER POWER
AV
TV
DOCK
DVD
AUX1
STB
TV
AUX2
AUX3
TV
INPUT1 MACRO
SEARCH
MEMORY
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
Cable clamp (×1)
9
SUR. DECODE
(Orange)
+10
ENTRY
MENU
TV/AV
ENTER
YSP
DISPLAY
Digital audio pin cable (×1)
3BEAM
IntelliBeam microphone
(×1)
Audio pin cable (×1)
RETURN
VOLUME
CH
MUTE
TV INPUT
CH LEVEL
TEST
TV VOL
(White/Red)
TV MUTE
CODE SET
Cardboard microphone
stand (×1)
Batteries (×2)
(AA, R6, UM-3)
Indoor DAB antenna (×1)
QUICK REFERENCE
GUIDE
OSD* video pin cable (×1)
(Yellow)
* OSD: On-Screen Display
Demonstration DVD
(×1)
6 En
AC power supply cable (×1)
Controls and functions
Controls and functions
INTRODUCTION
Front panel
AUX 3
INTELLIBEAM MIC
INPUT
1
3
4
AUX 3
INTELLIBEAM MIC
VOLUME
+
STANDBY/ON
2
5
6
INPUT
VOLUME
7
+
STANDBY/ON
1 Front panel display
Shows information about the operational status of this
unit.
6 VOLUME +/–
Controls the volume level of all audio channels (see
page 46).
2 Remote control sensor
Receives infrared signals from the remote control.
7 STANDBY/ON
Turns on the power of this unit or sets it to the standby
mode (see page 30).
3 AUX 3 input jack
Connect your portable audio player (see page 24).
4 INTELLIBEAM MIC jack
Connect the supplied IntelliBeam microphone for AUTO
SETUP (see page 35).
5 INPUT
Press repeatedly to switch between input sources (see
page 44).
Outputs a test tone to experience the sound beam (see
page 102).
Notes
• When you turn on this unit, you will hear a click sound
followed by the 4 to 5-second interval before sound
reproducing.
• In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control or to search for HDMI signals.
English
7 En
Controls and functions
Front panel display
1
2
0ABC D
3
E
4
F G
5
6
7
8
9
I
H
1 HDMI indicator
Lights up when the signal of the selected input source is
input at the HDMI IN jack(s).
C NIGHT indicator
Lights up when one of the night listening enhancers is
selected (see page 75).
2 TUNER indicators
Light up when this unit is receiving a DAB service
(see page 49).
D SLEEP indicator
Lights up when the sleep timer is set (see page 76).
3 DAB indicator
Lights up when DAB (Digital Audio Broadcasting) is
selected as the input source (see page 49).
E SECONDARY indicator
Lights up when this unit is receiving a DAB subchannel
(see page 49).
4 CINEMA DSP indicator
Lights up when a sound field program is selected (see
page 71).
F DRC indicator
Lights up when “DRC MODE” is set to “AUTO” (see
page 55) and DRC (Dynamic Range Control) data is
transmitted in the DAB tuner mode.
5 PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
G PRESET indicator
Lights up when PRESET is selected as the DAB tuning
mode (see page 49).
6 Decoder indicators
Light up when the corresponding decoder operates
(see page 62).
H Multi-information display
Shows information with alphanumeric characters when
you adjust the parameters of this unit.
7 ENHANCER indicator
Lights up when the Music Enhancer is selected (see
page 74).
I Input channel indicators
Show information when you adjust the parameters of this
unit. The channel component of the current digital input
signal is displayed (see page 62).
8 DUAL indicator
Lights up when dual monaural signals are being input to
this unit when this unit is in the DAB tuning mode.
9 Volume level indicator
Displays the current volume level.
0 DOCK indicator
Lights up when your iPod (Click and Wheel), iPod nano,
or iPod mini is connected to this unit via the DOCK
terminal on this unit.
A SRS TruBass indicator
Lights up when TruBass is turned on (see page 88).
B EQUAL indicator
Lights up when the TV volume equal mode is selected
(see page 75).
8 En
y
You can adjust the brightness and display setting of the front
panel display using the F.DISPLAY SET parameter in MANUAL
SETUP (see page 92).
Controls and functions
Rear panel
DVD
INTRODUCTION
AUX 1
1
2
4
IN
5
3
OUT
HDMI
IR-OUT
IR-OUT
6
7 8
DAB75
UNBAL.
COMPONENT
COMPONENT
9
0
A
B
C
D
IR IN
RS-232C
ANTENNA
SUBWOOFER
COMPONENT
DVD
AUX 2
COAXIAL
OPTICAL
STB
VIDEO OUT
E
F G
DVD/AUX 2
VIDEO IN
H I
AUX 1
J
TV/STB AUX 1
AUDIO IN
K
1 AUX 1 HDMI IN jack
Connect your digital satellite tuner, cable TV tuner, digital
air wave tuner, or game console via an HDMI connection
(see page 19).
2 DVD HDMI IN jack
Connect your DVD player via an HDMI connection (see
page 19).
3 HDMI OUT jack
Connect to the HDMI IN jack on your HDMI component
such as a TV or a projector connected to this unit (see
page 19).
4 AC IN
Connect the supplied AC power supply cable
(see page 28).
5 IR-OUT terminal
This is a control expansion terminal for commercial use
only (see page 27).
6 ANTENNA jack
Connect the DAB antenna (see page 27).
TV/STB
AUX 1
DIGITAL IN
L
M
8 TV/STB AUDIO IN jacks
Connect your TV, digital satellite tuner, or cable TV tuner
via an analog connection (see pages 20 and 22).
9 AUX 1 AUDIO IN jacks
Connect an external component via an analog connection
(see page 21).
0 DOCK terminal
Connect the Yamaha iPod universal dock (such as YDS10, sold separately) (see page 57).
A DVD COAXIAL DIGITAL IN jack
Connect your DVD player via a coaxial digital connection
(see page 21).
B AUX 2 COAXIAL DIGITAL IN jack
Connect an external component via a coaxial digital
connection (see page 25).
C IR IN terminal
This is a control expansion terminal for commercial use
only (see page 27).
D RS-232C terminal
This is a control expansion terminal for commercial use
only (see page 27).
9 En
English
7 SUBWOOFER jack
Connect your subwoofer (see page 26).
DOCK
Controls and functions
E VIDEO OUT jack
Connect to the video input jack of your TV via a
composite analog video connection to display the OSD of
this unit (see page 20).
F COMPONENT VIDEO OUT jacks
Connect to the video input jacks of your TV via a
component analog video connection to display the OSD of
this unit (see page 20).
G STB VIDEO IN jacks
Connect a digital satellite tuner or a cable TV tuner via a
composite analog video connection (see pages 22 to 23).
H STB COMPONENT VIDEO IN jacks
Connect a digital satellite tuner or a cable TV tuner via a
component analog video connection (see pages 22 to 23).
I DVD/AUX 2 VIDEO IN jacks
Connect a DVD player/recorder or an external component
via a composite analog video connection
(see pages 21 and 25).
J DVD/AUX 2 COMPONENT VIDEO IN jacks
Connect a DVD player/recorder or an external component
via a component analog video connection (see pages 21
and 25).
K AUX 1 VIDEO IN jacks
Connect an external component via a composite analog
video connection (see page 25).
L TV/STB OPTICAL DIGITAL IN jack
Connect your TV, digital satellite tuner, or cable TV tuner
via an optical digital connection (see pages 20 and 22).
M AUX 1 OPTICAL DIGITAL IN jack
Connect an external component via an optical digital
connection (see page 25).
10 En
Controls and functions
Remote control
y
You can also control other components using the remote control
once you set the appropriate remote control codes. See
“Controlling other components” on page 108 for details.
1
G
STANDBY/ON
POWER POWER
*2
3
AV
DOCK
DVD
*4
TV
AUX1
AUX2
AUX3
TV
INPUT1 MACRO
TV
STB
SEARCH
MEMORY
DAB
5
6
7
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
8
3BEAM
ENHANCER
9
+10
ENTER
MENU
TV/AV
YSP
0
DISPLAY
VOLUME
RETURN
CH
D
E
F
P
Q
R
S
TV VOL
t*
*A
*B
*C
M
N
O
9
SUR. DECODE
ENTRY
H*
I*
J*
K
L
MUTE
TV INPUT
CH LEVEL
TEST
TV MUTE
CODE SET
U*
V*
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 STANDBY/ON
Sets this system to the standby mode (see page 30).
3 Transmission indicator
Lights up when infrared control signals are being output.
INTRODUCTION
This section describes the functions of the remote control
used to control this unit. Some buttons marked with an
asterisk (*) share the common functions between the YSP
and TV/AV operation modes (R).
4 Input selector buttons
Use to select an input source (DVD, AUX1, AUX2,
AUX3/DOCK, STB, TV, or DAB).
5 VOL MODE
Turns on or off the volume modes (see page 75).
6 AUTO SETUP
Enters the AUTO SETUP menu (see page 34).
7 CINEMA DSP program buttons
Select the CINEMA DSP programs (see page 69).
8 ENHANCER
Turns on or off the Music Enhancer (see page 74).
9 Cursor buttons
/
/ /
Select and adjust SET MENU items.
, ENTER
0 DISPLAY
Displays information on the selected input signal.
A VOLUME +/–
Increases or decreases the volume level of this unit (see
page 46).
B MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level (see page 46).
C TV INPUT
Toggles between the input sources on the TV (see
page 108).
D CH LEVEL
Adjusts the volume level of each channel (see page 95).
E TEST
Outputs a test tone when adjusting the output level of each
channel (see page 94).
English
11 En
Controls and functions
F DVD player/VCR control buttons
Control your DVD player or VCR (see pages 109 and
110).
S RETURN
Selects sleep timer settings or returns to the previous SET
MENU screen.
G My Beam microphone
Collects the test tones from this unit when using the My
Beam auto-adjust function (see page 67).
T TV VOL +/–
Adjusts the volume level of your TV (see page 108).
H TV POWER
Turns on the power of your TV or sets it to the standby
mode (see page 108).
I AV POWER
Turns on the power of the selected component or sets it to
the standby mode (see pages 109 and 110).
J INPUT1
Switches the input source on your TV (see page 108).
K MACRO
Use to set the TV macro (see page 111).
L /5
Selects a DAB service or a preset DAB service number
when this unit is receiving a DAB service (see page 50).
Note
This function is available only when DAB services are preset.
M SLEEP
Sets the sleep timer (see page 76).
N INPUTMODE
Toggles between input modes (AUTO, DTS, and
ANALOG) (see page 97).
O Beam mode buttons
Change the beam mode settings (see pages 60, 66, and
67).
P SUR. DECODE
Selects the surround mode for playback (see page 63).
Q MENU
Displays the setup menu on your TV monitor (see
pages 36 and 81).
R Operation mode selector
Selects the operation mode of this unit. Select YSP when
operating this unit and select TV/AV when operating your
TV or other AV components.
12 En
U CH +/–
Changes the channels of your TV, digital satellite tuner,
cable TV tuner, or VCR (see pages 108 and 110).
V TV MUTE, CODE SET
Mutes the audio output of your TV (see page 108).
Sets up remote control codes (see page 107).
Controls and functions
This section describes the functions of the remote control
used to control DAB or iPod when the TV/AV mode is
selected with the operation mode selector (7).
1 SEARCH
DAB: Switches between the DAB tuning modes
(see page 49).
STANDBY/ON
POWER POWER
AV
TV
DOCK
DVD
AUX1
AUX2
AUX3
TV
INPUT1 MACRO
TV
STB
SEARCH
1
2
MEMORY
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
ENHANCER
3
9
+10
ENTRY
ENTER
MENU
TV/AV
YSP
DISPLAY
RETURN
4
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
CH LEVEL
TEST
CODE SET
y
These functions are also available when this unit is playing back
your iPod (see page 58).
When the operation mode of this unit is set to YSP, you can also
use /5 instead of using the cursor buttons
/ .
SUR. DECODE
OFF
0
5
3 Cursor buttons
/
/ / , ENTER
DAB: Use ENTRY ( / ) to select a DAB service or
a preset DAB service number (see page 50). Use / to
move to the top of the DAB service registry list (see
page 50).
INTRODUCTION
2 Numeric buttons
DAB: Enter numbers to select a preset DAB service.
6
7
8
4 DISPLAY
DAB and iPod: Displays information when this unit is
receiving DAB service (see page 52) or playing back your
iPod (see page 57).
5 MEMORY
DAB: Stores the preset DAB services (see pages 50).
6 MENU
DAB: Displays the DAB menu on your TV monitor
(see page 53).
7 Operation mode selector
Selects the operation mode of this unit. Select YSP when
operating this unit and select TV/AV when operating your
TV or other AV components.
8 RETURN
DAB: Returns to the previous DAB menu level (see
page 53).
English
13 En
Installation
Installation
This section describes a suitable installation location to install this unit using a metal wall bracket, a rack or a stand.
Depending on your installation environment, connections with external components can be done before installing this
unit. We recommend that you temporarily place and arrange all components, including this unit, in order to decide which
procedure should come first. Especially when you make a connection over HDMI, we recommend that you make a
connection first before installation (see page 19).
Before installing this unit
Notes
This unit creates surround sound by reflecting projected
sound beams off the walls of your listening room. The
surround sound effects produced by this unit may not be
sufficient when this unit is installed in the following
locations.
• Rooms with walls inadequate for reflecting sound
beams
• Rooms with acoustically absorbent walls
• Rooms with measurements outside the following
range: W (3 to 7 m (10 to 23 ft)) x H (2 to 3.5 m (7 to
11.5 ft)) x D (3 to 7 m (10 to 23 ft))
• Rooms with less than 1.8 m (6 ft) from the listening
position to this unit
• Rooms where objects such as furniture are likely to
obstruct the path of sound beams
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of
this unit
y
• You can enjoy surround sound by selecting My Surround (see
page 61) as the beam mode even if your listening room may not
fulfill the above conditions (except when the listening position
is not directly facing toward the front of this unit).
• You can also enjoy surround sound by selecting 2-channel or
5-channel stereo playback (see page 66) or My Beam (see
page 67) as the beam mode even if your listening room may not
fulfill the above conditions.
• We do not recommend putting this unit directly on the floor of
your listening room. Please install this unit using a metal wall
bracket, a rack, or a stand.
• This unit weighs 15.5 kg (34 lbs 3 oz). Be sure to install this
unit where it will not fall subject to vibrations, such as from an
earthquake, and where it is out of the reach of children.
• When using a cathode-ray tube (CRT) TV, do not install this
unit directly above your TV.
• This unit is shielded against magnetic rays. However, if the
picture on your TV screen becomes blurred or distorted, we
recommend moving this unit away from your TV.
Installing this unit
Install this unit where there are no obstacles such as
furniture obstructing the path of sound beams. Otherwise,
the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the
corner.
Parallel installation
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
An object, such as
furniture
Make sure you leave an adequate amount of ventilation
space so that heat can escape. Make at least 5 cm (2 in) of
space above or below this unit.
Side view
Corner installation
Install this unit in the corner at a 40º to 50º angle from the
adjacent walls.
5 cm (2 in) or more
Front
40° to 50°
Rear
Side
An object, such as furniture
14 En
Installation
■ Installation examples
Example 1
Install this unit as close to the exact center of the wall as possible.
PREPARATION
Example 2
Install this unit so that the sound beams can be reflected off the walls.
Example 3
Install this unit as close to the exact front of your normal listening position as possible.
English
15 En
Installation
■ Using a metal wall bracket
■ Using a rack
You can use the optional metal wall bracket (such as SPMK30) to mount this unit on the wall in your listening room.
You can install this unit either above or under your TV in a
commercially available rack.
Metal wall bracket
When this unit is installed above your TV
This unit
TV
YSP-40D
355
150
355
92
112
24- 7x22
150
4- 7
When this unit is installed under your TV
(mm)
730
SPM-K30 (Option)
Note
y
Refer to the instructions supplied with the metal bracket for
details on how to attach the metal bracket to the wall or how to
attach this unit to the metal bracket.
Make sure that the rack is large enough to allow adequate
ventilation space around this unit (see page 14) and that it is
strong enough to support the weight of both this unit and your TV.
■ Affixing this unit
■ Using a stand
You can mount your TV on a stand placed on a
commercially available rack and install this unit under
your TV.
Peel off the film from each of the four supplied fasteners
and then secure them to the bottom four corners of this
unit and the top of the rack, etc.
This unit
Stand
Peel off
the pad
on the
bottom
TV
Peel off 2
the film
1
Fasteners
Notes
This unit
y
Refer to the instructions supplied with the stand for details on
how to install the stand or how to mount and the TV on the stand.
16 En
• Do not install this unit on top of a slanted surface. This unit may
fall over and cause injury.
• Make sure you wipe the surface of the rack, etc. before securing
the fasteners. Applying the tape to a dirty or wet surface will
weaken the sticking power of the tape, and this unit may fall as
a result.
Connections
Connections
This unit is equipped with the following types of audio/video input/output jacks/terminal:
For audio input
• 2 optical digital input jacks
• 2 coaxial digital input jacks
• 2 sets of analog input jacks
• 1 universal dock terminal
For audio output
• 1 subwoofer output jack
For audio/video input
• 2 HDMI input jacks
For video output
• 1 composite video output jack
• 1 set of component video output jacks
For audio/video output
• 1 HDMI output jack
Use these jacks/terminal to connect external components such as your TV, DVD player, VCR, digital satellite tuner, cable
TV tuner, digital air wave tuner, portable audio player, game console, and iPod. Further, by connecting a subwoofer to
this unit, you can enjoy reinforced low-bass sounds. For details on how to connect various types of external components
to this unit, see pages 19 to 26.
PREPARATION
For video input
• 3 composite video input jacks
• 2 sets of component video input jacks
CAUTION
• Do not connect this unit or other components to the mains power until all connections between components are
complete.
• Unplug the AC power supply cable before changing connections, moving or cleaning this unit.
Audio connection
Video connection
TV
This unit
AUX 3
Subwoofer
INPUT
portable audio
player
VOLUME
+
STANDBY/ON
Digital satellite tuner
or cable TV tuner
VCR or game console
17 En
English
DVD player
INTELLIBEAM MIC
Connections
Before connecting components
■ Cables used for connections
■ Affixing cables
To prevent cables from becoming unplugged, place the supplied
cable clamp with the open side facing upward, attach it to the rear
panel of this unit in a suitable position, and then affix cables in
the cable clamp.
Audio/Video
A
HDMI cable
Optical cable
Attach to this unit
Audio
Audio pin cable (supplied)
(White)
(White)
■ Information on HDMI™
Audio signals
(Red)
(Red)
Optical cable (supplied)
Digital audio pin cable (supplied)
(Orange)
Input source
Audio signal type
DVD video
Dolby Digital, DTS, PCM
DVD audio
2-channel stereo
(up to 96 kHz/24 bit)
Blu-ray Disc
HD DVD
Dolby Digital, DTS, PCM
(Orange)
Notes
5
3.5 mm stereo mini plug cable
• When CPPM copy-protected DVD audio is played back, video and
audio signals may not be output depending on the type of DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or
DVI components.
Subwoofer pin cable
y
• We recommend that you use an HDMI cable shorter than 5 m
(16 ft) with the HDMI logo printed on it.
• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect
this unit to other DVI components.
Video
■ Priority order for audio input signals
OSD video pin cable (supplied)/ Video pin cable
(Yellow)
(Yellow)
Component video pin cable
(Green)
(Green)
(Blue)
(Blue)
(Red)
(Red)
■ Notes on connecting the optical cable
• Pull out the cap before connecting the optical cable.
When you are not using the optical cable, be sure to put the cap
back in place.
• When inserting the cable into the optical digital jack, make sure
the direction is correct.
Cap
18 En
When multiple types of audio signals are simultaneously
being input from a single source component, this unit
plays back the audio signals in the following priority
order: HDMI → Digital → Analog
As default settings, the following input jacks are assigned
to the corresponding input sources:
Input
Source
Input
jack
TV/STB
DVD
AUX 1
AUX 2
AUX 3
HDMI
Digital
Analog
Connections
Connections using HDMI cables
This unit is equipped with 2 HDMI input jacks and 1 HDMI output jack. If your TV and other components have HDMI
jacks, use HDMI cables for simpler and easier connections, and you can skip the connection procedures from page 20 to
23. If your TV has a built-in digital satellite tuner and an optical digital output jack, connect the optical digital output jack
on your TV to the TV/STB OPTICAL DIGITAL IN jack on this unit.
y
• We recommend that you secure the HDMI cable(s) with adhesive tape, etc. once you have connected the HDMI cable(s) to the HDMI
jack(s) of this unit.
• This unit outputs analog video signal and analog/digital audio signals input at the video/component video jacks and analog/digital
input jacks at the HDMI OUT jack.
PREPARATION
Rear panel of this unit
AUX 1
DVD
IN
*
OUT
HDMI
This connection (except for a game
console) is not necessary if your
TV has a built-in digital satellite
tuner, cable TV tuner, or digital
airwave tuner.
*
A
A
HDMI
input
A
HDMI
output
DVD player/recorder
TV
HDMI
output
Digital satellite tuner,
cable TV tuner,
digital airwave tuner,
or game console
Audio/Video
A
HDMI cable
English
19 En
Connections
Connecting a TV
For audio connection, connect the analog audio output jacks on your TV to the TV/STB AUDIO IN jacks on this unit. If
your TV has an optical digital output jack, connect the optical digital output jack on your TV to the TV/STB OPTICAL
DIGITAL IN jack on this unit.
For video connection, connect the video input jack on your TV to the VIDEO OUT jack on this unit to display the OSD
for easy viewing when you adjust the system parameters in SET MENU. If your TV has component video input jacks,
connect the component video input jacks of your TV to the COMPONENT VIDEO OUT jacks of this unit in addition to
the composite video connection. Once the component video connection is made, you can enjoy images with better
resolution.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 18).
Note
If you make analog and optical digital audio connections at the same time as shown in the illustration below, the digital audio signals
input at the TV/STB OPTICAL DIGITAL IN jack take priority over the analog audio signals input at the TV/STB AUDIO IN jacks.
Rear panel of this unit
COMPONENT
DVD
AUX 2
COAXIAL
OPTICAL
TV/STB AUX 1
AUDIO IN
VIDEO OUT
R
Video
input
Component
video input
TV/STB
AUX 1
DIGITAL IN
L
Analog
audio
output
Optical
digital
output
TV
Video
Audio
OSD video pin cable
Audio pin cable
Component video pin cable
Optical cable
20 En
Connections
Connecting a DVD player/recorder
For audio connection, connect the coaxial digital output jack on your DVD player/recorder to the DVD COAXIAL
DIGITAL IN jack on this unit. When you connect this unit to your DVD/VCR combo player/recorder, connect the analog
audio output jacks on your DVD/VCR combo player/recorder to the AUX 1 AUDIO IN jacks on this unit in addition to
the coaxial digital audio connection.
For video connection, connect the video output jack of your DVD player/recorder to the DVD/AUX 2 VIDEO IN jack of
this unit. If your DVD player/recorder has component video output jacks, connect the component video output jacks of
your DVD player/recorder to the DVD/AUX 2 COMPONENT VIDEO IN jacks of this unit. Once the component video
connection is made, you can enjoy images with better resolution.
y
Notes
• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system
settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.
• If your DVD player/recorder does not have a coaxial digital output jack, make an optical digital audio connection instead (see
page 25).
PREPARATION
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 18).
Rear panel of this unit
COMPONENT
COMPONENT
SUBWOOFER
DVD
AUX 2
COAXIAL
OPTICAL
STB
DVD/AUX 2
VIDEO IN
*1You can only make
*1
either a composite
or a component
connection.
*1
AUX 1
*2
TV/STB AUX 1
AUDIO IN
*2For
the DVD/
VCR combo
player/recorder
connection
R
Video
output
Component
video output
Video signal to the TV
Video
output
TV/STB
AUX 1
DIGITAL IN
*2
L
Analog
audio
output
Coaxial
digital
output
DVD player/recorder
Video
Audio
Audio pin cable
Component video pin cable
Digital audio pin cable
English
Video pin cable
21 En
Connections
Connecting a digital satellite tuner or a cable TV tuner
For audio connection, connect the optical digital output jack on your digital satellite tuner or cable TV tuner to the TV/
STB OPTICAL DIGITAL IN jack on this unit. Connect the analog audio output jacks on your digital satellite tuner or
cable TV tuner to the TV/STB AUDIO IN jacks on this unit.
For video connection, connect the video output jack of your digital satellite tuner or cable TV tuner to the STB VIDEO
IN jack of this unit. If your digital satellite tuner or cable TV tuner has component video output jacks, connect the
component video output jacks of your digital satellite tuner or cable TV tuner to the STB COMPONENT VIDEO IN
jacks of this unit. Once the component video connection is made, you can enjoy images with better resolution.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 18).
Rear panel of this unit
COMPONENT
COMPONENT
SUBWOOFER
DVD
AUX 2
COAXIAL
OPTICAL
STB
*
DVD/AUX 2
VIDEO IN
*
*
AUX 1
You can only make
either a composite
or a component
connection.
R
Video
output
Component
video output
Video signal to the TV
*
TV/STB
AUX 1
DIGITAL IN
TV/STB AUX 1
AUDIO IN
This connection (except for a game console) is not
necessary if your TV has a built-in digital satellite
tuner, cable TV tuner, or digital airwave tuner.
L
Analog
audio
output
Optical
digital
output
Digital satellite tuner
or cable TV tuner
Video
Audio
Video pin cable
Audio pin cable
Component video pin cable
Optical cable
22 En
Connections
Connecting a digital airwave tuner
For audio connection, connect the TV/STB AUDIO IN jacks on this unit to the analog audio output jacks on your TV.
Connect the optical digital output jack on your digital airwave tuner to the TV/STB OPTICAL DIGITAL IN jack on this
unit in addition to the analog audio connection. By doing so, you can enjoy both analog and digital broadcasts.
For video connection, connect the video output jack of your digital airwave tuner to the STB VIDEO IN jack of this unit.
If your digital airwave tuner has component video output jacks, connect the component video output jacks of your digital
airwave tuner to the STB COMPONENT VIDEO IN jacks of this unit. Once the component video connection is made,
you can enjoy images with better resolution.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 18).
PREPARATION
Rear panel of this unit
COMPONENT
COMPONENT
SUBWOOFER
DVD
AUX 2
COAXIAL
OPTICAL
STB
*
Video
output
DVD/AUX 2
VIDEO IN
*
*
TV/STB
AUX 1
DIGITAL IN
TV/STB AUX 1
AUDIO IN
You can only make
either a composite
or a component
connection.
Component
video output
Video signal to the TV
*
AUX 1
Connect to the analog
audio output jacks on
the TV.
Optical
digital
output
Digital airwave tuner
This connection (except for a game console) is not
necessary if your TV has a built-in digital satellite
tuner, cable TV tuner, or digital airwave tuner.
Video
Audio
Audio pin cable
Component video pin cable
Optical cable
English
Video pin cable
23 En
Connections
Connecting a portable audio player
Connect the analog audio output jack on your portable audio player to the AUX 3 input jack on the front panel of this
unit.
Front panel of this unit
AUX 3
INTELLIBEAM MIC
INPUT
AUX 3
Analog
audio
output
Portable audio player
Audio
3.5 mm stereo mini plug cable
24 En
VOLUME
+
STANDBY/ON
Connections
Connecting other external components
If your component supports optical digital connections, connect the optical digital output jack on your component
(e.g., DVD player/recorder) to the AUX 1 OPTICAL DIGITAL IN jack on this unit. If your component does not support
optical digital connections, connect the coaxial digital output jack on your component to the AUX 2 COAXIAL
DIGITAL IN jack on this unit. If your component does not support any digital connections, connect the analog audio
output jacks on your component (e.g., VCR) to the AUX 1 AUDIO IN jacks on this unit.
For video connection, connect the video output jack of your DVD player/recorder, etc. to the DVD/AUX 2 VIDEO IN (or
AUX 1 VIDEO IN) jack of this unit. If your DVD player/recorder, etc. has component video output jacks, connect the
component video output jacks of your DVD player/recorder, etc. to the DVD/AUX 2 COMPONENT VIDEO IN jacks of
this unit. Once the component video connection is made, you can enjoy images with better resolution.
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 18).
Note
If you make analog and digital audio connections at the same time as shown in the illustration below, the digital audio signals input at
the AUX 1 OPTICAL DIGITAL IN or AUX 2 COAXIAL DIGITAL IN jack take priority over the analog audio signals input at the AUX
1 AUDIO IN jacks.
PREPARATION
y
Rear panel of this unit
COMPONENT
COMPONENT
SUBWOOFER
DVD
AUX 2
COAXIAL
OPTICAL
STB
*You
can only
make either a
composite or a
component
connection.
DVD/AUX 2
VIDEO IN
*
AUX 1
TV/STB AUX 1
AUDIO IN
TV/STB
AUX 1
DIGITAL IN
*
R
Video
output
Component
video output
Video signal to
the TV
Video
output
L
Analog
audio
output
Optical
digital
output
Coaxial
digital
output
DVD player/recorder, VCR,
game console, CD player, etc.
Video
Audio
Audio pin cable
Component video pin cable
Optical cable
English
Video pin cable
Digital audio pin cable
25 En
Connections
Connecting a subwoofer
Connect the monaural input jack on your subwoofer to the SUBWOOFER jack on this unit.
This connection alone does not output sound from the connected subwoofer. To output sound from the connected
subwoofer, turn on the power of your subwoofer and then run AUTO SETUP (see page 34) or select SWFR for BASS
OUT in SUBWOOFER SET (see page 86).
Rear panel of this unit
COMPONENT
VIDEO OUT
COMPONENT
STB
COMPONENT
DVD/AUX 2
VIDEO IN
5
Monaural
input
Subwoofer
Audio
5
Subwoofer pin cable
26 En
SUBWOOFER
AUX 1
Connections
Connecting the DAB antenna
Connect the supplied DAB antenna to the ANTENNA jack on this unit and secure the DAB antenna vertically in an
unobtrusive location.
y
It is recommended that you use TUNE AID (see page 54) when connecting the DAB antenna in order to maximize DAB reception
capability.
Notes
PREPARATION
• Be sure to check the DAB coverage in your area as not all areas are presently covered. For a list of country DAB statuses and
worldwide DAB frequencies, visit WorldDAB online at “http://www.worlddab.org/”.
• The supplied indoor DAB antenna should provide sufficient signal strength. However, if the DAB signals are weak, use a
commercially available outdoor DAB antenna for better reception.
Indoor DAB antenna (supplied)
DAB75
UNBAL.
COMPONENT
ANTENNA
COMPONENT
SUBWOOFER
Rear panel of this unit
STB
DVD/AUX 2
VIDEO IN
AUX 1
About the RS-232C/IR-OUT/IR IN terminals
The RS-232C, IR-OUT, and IR IN terminals do not support normal external component connections. They are control
expansion terminals for commercial use only.
Rear panel of this unit
IR-OUT
IR-OUT
IR IN
RS-232C terminal
English
IR IN terminal
RS-232C
IR-OUT terminal
27 En
Connections
Connecting the AC power supply cable
Once all other connections are complete, plug one end of the AC power supply cable into the AC IN terminal of this unit
and then plug the other end into the AC wall outlet.
Rear panel of this unit
IR-OUT
AC IN
To the AC wall outlet
28 En
GETTING STARTED
Getting started
Installing batteries in the remote
control
y
Remove the transparent sheet before using the remote control.
Press
Operation range of the remote
control
Press and hold the
mark on the battery
cover and then open the cover.
2
Insert the two supplied batteries (AA, R6,
UM-3) into the battery compartment.
Make sure you insert the batteries according to the
polarity markings (+/–).
3
AUX 3
INTELLIBEAM MIC
INPUT
VOLUME
+
SETUP
1
The remote control transmits a directional infrared beam.
Use the remote control within 6 m (20 ft) of this unit and
point it toward the remote control sensor of this unit
during operation.
STANDBY/ON
Approximately
6 m (20 ft)
45
Close the battery cover.
45
Notes
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following places:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or a stove
– places of extremely low temperatures
– dusty places
• Do not expose the remote control sensor of this unit to direct
sunlight or lighting such as inverted fluorescent lamps.
• If the batteries grow old, the effective operation range of the
remote control decreases considerably. If this happens, replace
the batteries with two new ones as soon as possible.
English
• Change all of the batteries if you notice the following
conditions: the operation range of the remote control decreases
or the transmission indicator does not light up or becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• Exhausted batteries may leak. If the batteries have leaked,
dispose of them immediately. Avoid touching the leaked
material or letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing new
batteries.
• Do not throw away batteries with general house waste. Dispose
of them correctly in accordance with your local regulations.
• The memory stored in the remote control may be erased in the
following cases:
– The remote control is left without batteries for more than two
minutes.
– Exhausted batteries remain in the remote control.
– The buttons on the remote control are accidentally pressed
when you change batteries.
• If the memory stored in the remote control is unwantedly
erased, insert new batteries and set the remote control codes
again.
29 En
Getting started
Turning on this unit or
setting it to the standby mode
2
Press STANDBY/ON again to set this unit to
the standby mode.
Note
When this unit is in the standby mode, only STANDBY/ON on
the front panel or on the remote control is operational, and the
other control buttons on the front panel or on the remote control
are not operational until the power of this unit is turned on.
INPUT
VOLUME
+
STANDBY/ON
STANDBY/ON
POWER POWER
AV
TV
DOCK
DVD
AUX1
AUX2
AUX3
TV
INPUT1 MACRO
STB
TV
SEARCH
MEMORY
DAB
1
Press STANDBY/ON to turn on the power of
this unit.
The volume level appears in the front panel display,
and the current input source and beam mode are
displayed.
STANDBY/ON
or
STANDBY/ON
Front panel
Remote control
VOLUME 30
Current volume level
DVD
Current input
source
30 En
MY SUR
Current beam
mode
USING SET MENU
Using SET MENU
Displaying the OSD (on-screen display)
This section describes how to display the OSD (on-screen display) of this unit on your TV screen and to set the
parameters for your listening room. Once this is complete, you can enjoy real surround sound while watching TV in the
comfort of your own home.
1
Check that the video input jack on your TV is
connected to the VIDEO OUT jack on this unit
to display the OSD of this unit.
4
Set the operation mode selector to YSP.
TV/AV
YSP
2
Press STANDBY/ON to turn on the power of
this unit.
STANDBY/ON
5
Press MENU.
The SET MENU screen appears on your TV.
or
SET MENU
STANDBY/ON
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
Turn on the power of your TV.
MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
p
3
Remote control
SETUP
Front panel
English
31 En
Using SET MENU
The flow chart of SET MENU
The following diagram illustrates the overall flow of the setup procedure.
Run LANGUAGE SETUP.
See “Changing OSD language” on page 33.
Run AUTO SETUP (IntelliBeam).
See “AUTO SETUP (IntelliBeam)” on page 34.
If an error occurs
Look for a remedy.
See “Error messages for AUTO SETUP” on page 40 for a complete list of error
messages and possible remedies.
Play back audio signals or adjust the settings for the beam mode and the CINEMA DSP.
See “Playback” on page 44, “Enjoying surround sound” on page 60, and “Using sound field programs” on
page 69.
If you want to make additional settings
and adjustments
Run MANUAL SETUP.
See “MANUAL SETUP” on page 80.
y
• If you cannot clearly hear a sound beam from a specific channel, adjust settings for
SETTING PARAMETERS (see page 82) or for BEAM ADJUSTMENT (see page 83) in
BEAM MENU.
• If there are acoustically absorbent objects such as curtains in the path of the sound beams,
adjust settings for TREBLE GAIN in BEAM MENU (see page 85).
32 En
CHANGING OSD LANGUAGE
Changing OSD language
This feature allows you to select the language of your choice that appears in SET MENU of this unit.
1
Set the operation mode selector to YSP.
4
Press
/
to select the desired language,
and press ENTER.
TV/AV
YSP
ENTER
ENTER
2
Press MENU.
The SET MENU screen appears on your TV.
SET MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
MENU
Choices: ENGLISH (English), DEUTSCH (German),
Français (French), ESPAÑOL (Spanish),
ITALIANO (Italian), NEDERLANDS (Dutch),
Русский (Russian)
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
SETUP
y
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN.
• To exit from SET MENU, press MENU once more.
• You can also perform the following operations while
viewing information in the front panel display.
3
Press
/
to select LANGUAGE SETUP,
and press ENTER.
The following screen appears on your TV.
ENTER
ENTER
;LANGUAGE SETUP
. ENGLISH
DEUTSCH
Francais
ESPANOL
ITALIANO
NEDERLANDS
p
p
[ ]/[ ]:Select
[ENTER]:Return
English
33 En
AUTO SETUP (INTELLIBEAM)
AUTO SETUP (IntelliBeam)
This unit creates a sound field by reflecting sound beams on the walls of your listening room and by broadening the
cohesion of all the channels. Just as you would arrange the speaker position of other audio systems, you need to set the
beam angle to enjoy the best possible sound from this unit.
This unit employs the beam optimization and sound optimization features with the aid of the supplied IntelliBeam
microphone, allowing you to avoid troublesome listening-based setup and achieving highly accurate sound adjustments
that best match your listening environment. We call these two features “IntelliBeam” generically.
Beam optimization:
This feature optimizes the beam angle so that the parameter best matches your listening environment.
Sound optimization:
This feature optimizes the beam delay, volume, and quality so that the parameters best match your listening environment.
The flow chart of AUTO SETUP
This unit performs a series of checks to optimize the beam angle, delay, volume, and quality. You can choose to optimize
all or part of the parameters.
Notes
Checking the environment of
your listening room
*1
Optimizing the beam angle
Beam
optimization
*2 *3
Checking the subwoofer and
optimizing the beam delay,
frequency, and volume
34 En
Sound
optimization
*1 The beam angle checking procedure is skipped if SOUND
OPTIMZ only is selected.
*2 The sound optimization procedure is skipped if BEAM
OPTIMZ only is selected.
*3 The subwoofer checking procedure is skipped if BEAM
OPTIMZ only is selected.
AUTO SETUP (IntelliBeam)
Installing the IntelliBeam microphone
The supplied IntelliBeam microphone collects and analyzes the sound that this unit produces in your actual listening
environment. Follow the procedure below to connect the IntelliBeam microphone to this unit and make sure that the
IntelliBeam microphone is placed in a proper location and that there are no large obstacles between the IntelliBeam
microphone and the walls in your listening room.
Notes
MIN
MAX
MIN
SETUP
• After you have completed the AUTO SETUP procedure, be sure to disconnect the IntelliBeam microphone.
• The IntelliBeam microphone is sensitive to heat.
– Keep it away from direct sunlight.
– Do not place it on top of this unit.
• Do not connect the IntelliBeam microphone to an extension cable as doing so may result in an inaccurate sound optimization.
• An error may occur during the AUTO SETUP procedure if the IntelliBeam microphone is not properly placed in your listening room.
To avoid the possibility of an error:
– Do not place the IntelliBeam microphone to the extreme right or left from the center of this unit.
– Do not place the IntelliBeam microphone within 1.8 m (6.0 ft) from the front of this unit.
– Do not place the IntelliBeam microphone more than 1 m (3.3 ft) upper or lower from the center height of this unit.
• Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects
obstruct the path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the
walls.
• The best possible results are achieved if the IntelliBeam microphone is placed at the same height as your ears would be when you are
seated in your listening position. However, if this is not possible, you can manually fine-tune the sound beam angle and balance the
sound beam output levels using MANUAL SETUP (see page 80) once the AUTO SETUP procedure is completed.
• If a subwoofer with adjustable volume and crossover/high-cut frequency controls is connected to
CROSSOVER
VOLUME
HIGH CUT
this unit, set the volume between 11 and 1 o’clock as viewed on a conventional clockface and set
the crossover/high-cut frequency to the maximum.
MAX
Subwoofer
1
Press STANDBY/ON to turn off the power of
this unit.
STANDBY/ON
or
STANDBY/ON
Front panel
2
Remote control
Connect the supplied IntelliBeam
microphone to the INTELLIBEAM MIC jack on
the front panel.
AUX 3
3
Place the IntelliBeam microphone on a flat
level surface more than 1.8 m (6.0 ft) from the
front of the unit and within 1 m (3.3 ft) upper
or lower from the center height of the unit
with the IntelliBeam microphone facing
upward at your normal listening position.
Note
Be sure to place the IntelliBeam microphone on an
imaginary center line drawn from this unit.
y
You may want to use the supplied cardboard microphone
stand to affix the IntelliBeam microphone at the same height
as your ears would be when you are seated in your listening
position.
INTELLIBEAM MIC
IntelliBeam
microphone
INTELLIBEAM MIC
More than
1.8 m (6.0 ft)
Within 1 m (3.3 ft)
upper or lower from
the center height
English
Cardboard
microphone stand
Upper bound
position of the
microphone
Sofa
Lower bound
position of the
microphone
35 En
AUTO SETUP (IntelliBeam)
Using AUTO SETUP (IntelliBeam)
Once the IntelliBeam microphone is firmly connected to
this unit and properly placed in your listening room,
follow the procedure below to start the AUTO SETUP
procedure.
You can also enter the AUTO SETUP procedure simply by
pressing and holding AUTO SETUP for more than two
seconds. In this case, this unit performs both of the beam
optimization and sound optimization procedures.
Center line
IntelliBeam
microphone
■ Assembling the supplied cardboard
microphone stand
You will find three separate parts (one circular part and
two longitudinal parts) of the cardboard microphone stand
originally put together.
INPUT
1
VOLUME
+
STANDBY/ON
2
STANDBY/ON
POWER POWER
AV
TV
DOCK
AUX1
DVD
AUX2
AUX3
TV
INPUT1 MACRO
TV
STB
SEARCH
MEMORY
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
3
4
5BEAM
ST+3BEAM
1
2
3BEAM
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
0
ENHANCER
9
SUR. DECODE
OFF
+10
ENTRY
MENU
TV/AV
ENTER
YSP
1
Disassemble the three parts of the cardboard
microphone stand originally put together.
2
Insert one of the longitudinal part into the
crevice of the other longitudinal part.
3
Place the circular part on top of the two
combined longitudinal parts.
4
Place the supplied IntelliBeam microphone
on top of the circular part.
36 En
DISPLAY
VOLUME
RETURN
CH
TV VOL
AUTO SETUP (IntelliBeam)
3
Notes
• Make sure that your listening room is as quiet as possible while
this unit is performing the AUTO SETUP procedure.
• To achieve the best results possible, evacuate yourself from
your listening room until the AUTO SETUP procedure is
completed so that you may not obstruct the path of sound
beams.
• Be advised that it is normal for loud test tones to be output
during the AUTO SETUP procedure.
• The AUTO SETUP procedure may not be run successfully if
this unit is installed in one of the rooms described in “Before
installing this unit” on page 14. In such cases, run MANUAL
SETUP (see page 80) to manually adjust the corresponding
parameters.
• If an error occurs, an error buzzer is played, the AUTO SETUP
procedure stops, and an error message appears on the screen.
See “Error messages for AUTO SETUP” on page 40 for
appropriate remedies.
SET MENU
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
y
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN.
• To exit from the SET MENU screen, press MENU again.
• You can start the BEAM+SOUND OPTIMZ procedure
simply by pressing and holding AUTO SETUP for more
than two seconds. Steps 4 and 5 are skipped and then the
screen shown in step 5 is displayed on your TV. Start the
AUTO SETUP procedure from step 6.
• You can also perform the following operations in the front
panel display.
4
SETUP
1
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
MENU
y
• The AUTO SETUP procedure takes about three minutes
maximum. A chime is played when the AUTO SETUP
procedure is run successfully.
• If there are curtains in your listening room, we recommend
following the procedure below.
1. Open the curtains to improve sound reflection.
2. Run BEAM OPTIMZ only.
3. Close the curtains.
4. Run SOUND OPTIMZ only.
• You can save the settings optimized by the AUTO SETUP
procedure (see page 41). A set of settings optimized according
to the specific conditions of your listening environment can be
recalled later depending on the varying conditions of your
listening environment (see page 42).
Press MENU.
The SET MENU screen appears on your TV.
Press
/
to select AUTO SETUP and
press ENTER.
The following screen appears on your TV.
ENTER
ENTER
Press STANDBY/ON to turn on the power of
this unit.
If a subwoofer is connected to this unit, turn on the
power of the subwoofer.
STANDBY/ON
;AUTO SETUP
or
STANDBY/ON
Front panel
Remote control
. 1)BEAM+SOUND OPTIMZ
2)BEAM OPTIMZ only
3)SOUND OPTIMZ only
2
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
Set the operation mode selector to YSP.
TV/AV
YSP
English
37 En
AUTO SETUP (IntelliBeam)
5
Press
/
to select BEAM+SOUND
OPTIMZ, BEAM OPTIMZ only, or SOUND
OPTIMZ only and then press ENTER.
The following screen appears on your TV.
6
Check the following points once again before
starting the AUTO SETUP procedure.
• Is the IntelliBeam microphone firmly connected to
this unit?
• Is the IntelliBeam microphone placed in a proper
location?
• Are there any large obstacles in between the
IntelliBeam microphone and the walls in your
listening room?
7
Press ENTER to start the AUTO SETUP
procedure.
The following screen appears on your TV and the
AUTO SETUP procedure starts in 10 seconds.
Leave the room quietly before starting the AUTO
SETUP procedure.
ENTER
ENTER
AUTO SETUP
PREPARATION & CHECK
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
ENTER
BEAM+SOUND OPTIMZ
(Beam optimization and sound optimization)
Use to optimize the beam angle, delay, volume, and
quality so that the parameters best match your listening
environment.
It is recommended that you should select this optimization
feature in the following cases:
• If you make settings for the first time.
• If the unit has been relocated.
• If your listening room has been restructured.
• If the objects in your listening room (furniture, etc.)
have been rearranged.
This menu takes about three minutes.
BEAM OPTIMZ only
(Beam optimization only)
Use to optimize the beam angle so that the parameter best
matches your listening environment.
This menu takes about one minute.
SOUND OPTIMZ only
(Sound optimization only)
Use to optimize the beam delay, volume, and quality so
that the parameters best match your listening environment.
It is recommended that you should select this optimization
feature in the following cases:
• If you have opened or closed the curtains in your
listening room before using this unit.
• If you have manually set the beam angle.
This menu takes about two minutes.
Note
You must optimize the beam angle in the BEAM OPTIMZ only
procedure before starting the SOUND OPTIMZ only procedure.
38 En
AUTO SETUP START
Will begin in 10sec
Please leave the room
← Flashes
**-------[RETURN]:Cancel
If an error occurs, an error buzzer is played and an
error message is displayed. See “Error messages for
AUTO SETUP” on page 40 for a complete list of
error messages and their proper remedies. Follow the
instructions and perform the AUTO SETUP
procedure again.
AUTO SETUP (IntelliBeam)
8
Check that the following screen is displayed
on your TV.
The results of the AUTO SETUP procedure are
displayed on your TV.
9
Press ENTER to confirm the results or press
RETURN to cancel the results.
The following screen is displayed for two seconds
and then disappears from your TV.
Example 1
SHOW RESULT
MEASUREMENT COMPLETE
AUTO SETUP COMPLETE
← Flashes
Please remove the MIC from
the YSP and the listening
position.
ENTER
BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
Example 2
SHOW RESULT
MEASUREMENT COMPLETE
← Flashes
If “ENVIRONMENT CHECK [FAILED]” is displayed in
step 8, the following screen is displayed after pressing
ENTER. In this case, see ERROR E-1 in “Error messages
for AUTO SETUP” on page 40. Press ENTER to exit
AUTO SETUP and then run the procedure again from
step 3.
SETUP
ENVIRONMENT CHECK[FAILED]
BEAM MODE :5 BEAM
SUBWOOFER :YES
AUTO SETUP COMPLETE
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
Your YSP unit may not be set
up correctly.
We recommend you try again.
Please press [ENTER] key to
exit.
y
• If “ENVIRONMENT CHECK [FAILED]” is
displayed, we recommend running the AUTO SETUP
procedure again. For details, see step 9.
• If “SUBWOOFER : NOT APPLICABLE” is displayed
even though a subwoofer is connected to this unit,
increase the volume level of the subwoofer and run the
AUTO SETUP procedure again.
• Depending on the environment of your listening room,
the beam angle of front left and right, and surround left
and right may be set to the same value even if
“5 BEAM” is displayed as a result.
10
Disconnect the IntelliBeam microphone from
the INTELLIBEAM MIC jack on the front
panel.
AUX 3
INTELLIBEAM MIC
y
If you want to save and load settings, see “Using the system
memory” on page 41.
English
39 En
AUTO SETUP (IntelliBeam)
■ Error messages for AUTO SETUP
Before the AUTO SETUP procedure starts
Error message
ERROR E-2
No MIC detected. Please check
MIC connection and re-try.
Cause
The IntelliBeam microphone is not
connected to this unit.
Remedy
Connect the IntelliBeam microphone to
this unit.
See
page
35
While the AUTO SETUP procedure is in progress
If one of the errors listed below except E-1 is displayed, press RETURN. In case you have started the AUTO SETUP
procedure by pressing AUTO SETUP in step 3, run the procedure again from step 3 after the screen disappears. In case
you have started the AUTO SETUP procedure by pressing MENU in step 3, run the procedure again from step 4 after the
screen in step 3 is displayed. Run MANUAL SETUP if the problem is difficult to be saved.
Error message
Cause
Remedy
See
page
ERROR E-1
Please test in quieter environment.
There is too much unwanted noise in
your listening room.
Make sure that your listening room is as
quiet as possible. You may want to
choose certain hours during the day
when there is not much noise coming
from outside.
—
ERROR E-2
No MIC detected. Please check
MIC connection and re-try.
The IntelliBeam microphone was
disconnected while the AUTO SETUP
procedure was in progress.
Make sure that the IntelliBeam
microphone is firmly connected to this
unit.
35
ERROR E-3
Unexpected control is detected.
Please re-try.
Some other operations were performed
on this unit while the AUTO SETUP
procedure was in progress.
Do not perform any other operations
while the AUTO SETUP procedure is in
progress.
—
ERROR E-4
Please check MIC position. MIC
should be set in front of YSP.
The IntelliBeam microphone is not
placed in front of this unit.
Make sure that the IntelliBeam
microphone is installed in front of this
unit.
35
ERROR E-5
Please check MIC position. MIC
should be set above 1.8m/6.0ft.
The IntelliBeam microphone is not
placed in the right distance from this
unit.
Make sure that the IntelliBeam
microphone is installed more than 1.8 m
(6.0 ft) from the front of this unit and
within 1 m (3.3 ft) from the center height
of this unit.
35
ERROR E-6
Volume level is lower than
expected. Please check MIC
position/connection and re-try.
The IntelliBeam microphone cannot
collect the sound produced by this unit
because the sound output level is too low.
Make sure that the IntelliBeam
microphone is firmly connected to this
unit and placed in a proper location. If
the problem persists, contact the nearest
authorized Yamaha service center for
assistance.
35
ERROR E-7
Unexpected error happened.
Please re-try.
An internal system error occurred.
Repeat the AUTO SETUP procedure.
—
40 En
USING THE SYSTEM MEMORY
Using the system memory
Convenient usage of the system
memory
3
You can save the current settings adjusted in SET MENU
in the system memory of this unit. It is handy to save
certain settings according to the varying conditions of
your listening environment. For example, if there are
curtains in the path of sound beams, the effectiveness of
the sound beams will vary depending on whether the
curtains are open or closed.
Press
/
to select MEMORY and press
ENTER.
The following screen appears on your TV.
ENTER
ENTER
When the curtains are
closed
When the curtains are
open
;MEMORY
. 1)LOAD
2)SAVE
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
SETUP
4
Saving settings
1
Press
/
to select SAVE and press
ENTER.
The following screen appears on your TV.
Set the operation mode selector to YSP.
TV/AV
ENTER
ENTER
YSP
2
Press MENU.
The SET MENU screen appears on your TV.
SET MENU
MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
. MEMORY1
MEMORY2
MEMORY3
p
[ ]/[ ]:Select
[ENTER]:Enter
p
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
2)MEMORY SAVE
y
English
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN.
• To exit from the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
41 En
Using the system memory
5
Press
/
to select MEMORY1,
MEMORY2, or MEMORY3 and press ENTER.
The following screen appears on your TV.
ENTER
ENTER
Loading settings
You can recall the settings saved in “Saving settings” on
page 41 according to the varying conditions of your
listening environment.
1
Set the operation mode selector to YSP.
TV/AV
YSP
2)MEMORY SAVE
2
Press MENU.
The SET MENU screen appears on your TV.
MEMORY1 Save Now ?
SET MENU
Push [ENTER] to Save
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
MENU
6
Press ENTER again.
The new parameters are saved as MEMORY1,
MEMORY2, or MEMORY3. Once the parameters
are saved, the display returns to the SET MENU
screen.
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN.
• To exit from the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
2)MEMORY SAVE
MEMORY1 Saving
ENTER
3
Press
/
to select MEMORY and press
ENTER.
The following screen appears on your TV.
SET MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
ENTER
ENTER
7
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
;MEMORY
Press MENU to exit.
The SET MENU screen disappears from your TV.
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
42 En
p
MENU
. 1)LOAD
2)SAVE
Using the system memory
4
Press
/
to select LOAD and press
ENTER.
The following screen appears on your TV.
6
Press ENTER again.
The new parameters saved as MEMORY1,
MEMORY2, or MEMORY3 are loaded. Once the
parameters are loaded, the display returns to the SET
MENU screen.
1)MEMORY LOAD
ENTER
ENTER
MEMORY1 Loading
ENTER
1)MEMORY LOAD
. MEMORY1
MEMORY2
MEMORY3
SET MENU
p
p
[ ]/[ ]:Select
[ENTER]:Enter
Press
/
to select MEMORY1,
MEMORY2, or MEMORY3 and press ENTER.
The following screen appears on your TV.
7
ENTER
ENTER
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
5
SETUP
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
Press MENU to exit.
The SET MENU screen disappears from your TV.
MENU
1)MEMORY LOAD
MEMORY1 Load Now ?
Push [ENTER] to Load
English
43 En
PLAYBACK
Playback
Selecting the input source
You can play back sound from the components connected
to this unit simply by pressing INPUT on the front panel
repeatedly or pressing one of the input selector buttons
(TV, STB, DVD, AUX1, AUX2, or AUX3) on the remote
control. The name of the selected input source and the
type of corresponding input mode appear in the front
panel display.
■ Front panel operations
Press INPUT on the front panel repeatedly to
toggle between TV, STB, DVD, AUX1, AUX2, and
AUX3.
The name of the corresponding input source and the type
of current input mode are displayed in the front panel
display.
■ Remote control operations
y
In addition to controlling this unit, you can also operate other AV
components if you set up the remote control with the appropriate
remote control codes and set the operation mode selector to TV/
AV to change the control area (see page 107).
Press TV to play back a TV program.
TV
INPUT
VOLUME
+
STANDBY/ON
DOCK
DVD
AUX1
AUX2
AUX3
AUTO
TV/STB
TV
INPUT1 MACRO
STB
TV
SEARCH
MEMORY
Name of the selected
input source
Type of the selected
input mode
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
0
STB
9
SUR. DECODE
OFF
ENHANCER
+10
ENTRY
MENU
TV/AV
ENTER
YSP
DISPLAY
Press STB to play back a satellite broadcast.
AUTO
TV/STB
RETURN
Press DVD to play back a DVD.
DVD
DVD
44 En
AUTO
Playback
Press AUX1 (or AUX2) to play back a component
connected to the AUX 1 (or AUX 2) jack on the
rear panel of this unit.
2
Switch to the video input on your TV using
the remote control supplied with the TV and
display the DVD menu screen.
AUX1
Note
If necessary, turn down the volume of your TV until no
sound is heard.
AUX1
AUTO
3
DVD
Press AUX3 to play back a component connected
to the AUX 3 input jack on the front panel.
AUX3
Press DVD to select DVD as the input source.
4
Play back DVD on your DVD player using the
supplied remote control.
Audio signals from your DVD player are output from
this unit.
y
AUX3
Playing back sources
Note
input at the optical/coaxial/HDMI jack. If the PCM indicator
lights up, confirm the settings of the digital output, bitstream
output, DTS output, and/or HDMI output of the DVD player.
• If the output volume is too low, increase the volume of this unit
to around 45.
• If you have set the appropriate remote control codes for your
TV and DVD player, you can use the remote control supplied
with this unit to operate these components. For details on how
to set remote control codes, see page 107.
BASIC
OPERATION
Once an input source is selected (see page 44), you can
play back the selected input source.
• You can use the supplied demonstration DVD to check the
digital signals being input at the DVD player with the digital
connection (optical/coaxial/HDMI). The input channel and LFE
indicators light up when this unit detects the 5.1-channel signal
This section uses a DVD player as an example of the playback
source.
y
For details on your TV and DVD player, refer to the respective
owner’s manual.
1
Turn on the power of your DVD player.
English
45 En
Playback
■ Muting the sound
Adjusting the volume
TV VOL
VOLUME
CH
MUTE
TV INPUT
TV MUTE
CODE SET
1
Press MUTE to mute the sound.
“AUDIO MUTE ON” appears in the front panel
display, and the volume level indicator flashes.
MUTE
INPUT
VOLUME
+
STANDBY/ON
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
AUDIO MUTE ON
Flashes
Press VOLUME +/– to increase or decrease the
volume level.
The numeric value of the volume level appears in the front
panel display.
Control range: MIN (minimum), 01 to 99,
MAX (maximum)
DVD
2
VOLUME
or
VOLUME
5BEAM
Press MUTE again (or press VOLUME +/–) to
resume the sound output.
“AUDIO MUTE OFF” appears temporarily in the
front panel display (or the numeric value of the
current volume level appears if you press VOLUME
+/–), and the volume level indicator lights up.
VOLUME
+
MUTE
or
Front panel
Remote control
Lights up
VOLUME
30
AUDIO MUTE OFF
Notes
• The volume level of all input sources (including multi-channel
as well as stereo sources) changes at the same time.
• One volume level increases or decreases each time you press
VOLUME +/–.
• You can continuously increase or decrease the volume level if
you press and hold VOLUME +/–.
46 En
Note
The sound output of all input sources (including multi-channel as
well as stereo sources) is muted at the same time.
y
You can select whether the sound output is to be muted
completely or by 20 dB when you press MUTE (see page 87).
DAB (DIGITAL AUDIO BROADCASTING)
DAB (Digital Audio Broadcasting)
About DAB
Ensemble
DAB (Digital Audio Broadcasting), also known as digital
radio, is a new way of radio broadcasting. DAB is
broadcast using digital signals instead of analog signals,
resulting in near CD-quality sound. Analog signals (i.e.
AM/FM) are susceptible to interference (i.e. distortion and
noise) caused by electrical equipment, weather conditions,
tall buildings, mountains, etc.; digital signals are not.
Thus, with DAB, there is virtually interference-free
reception and no hiss or crackle.
Another advantage of DAB is that a large amount of
information can be carried within the digital signal. DAB
is broadcast in blocks of data called ensembles (also
known as multiplexes). Several radio programs (called
services) can be broadcast simultaneously in each
ensemble. This means that you can choose between
several radio programs within one frequency.
Audio signal and
service information
With DAB, there is no need to remember channel
frequencies, either. All broadcasts are selected by simply
selecting the service name.
Notes
• Be sure to check the DAB coverage in your area – not all areas
are presently covered. For a list of country DAB statuses and
worldwide DAB frequencies, visit WorldDAB online at
“http://www.worlddab.org”.
• The sound quality and service information are controlled by the
DAB broadcaster, not this unit. Not all DAB broadcasters
transmit PAD/SI information.
• DAB signals are broadcast in Band-III (218 – 230 MHz).
BASIC
OPERATION
In addition to the audio signal, service information is also
broadcast and displayed in the front panel display of this
unit. Part of the service information is text data
information called DLS (Dynamic Label Segment). For
more information, see page 52.
Service
English
47 En
DAB (Digital Audio Broadcasting)
Preparing the DAB tuning
Before tuning into DAB services, you must perform the
initial scan.
1
Press DAB repeatedly to select DAB.
“Initiate Scan” appears in the front panel display.
DAB
Initiate Scan
2
Press k / n / l / h to start the initial scan
operation.
This unit starts the scan for DAB ensembles. While
the scan is in progress, “Scanning” and the
percentage of the progress of the scan appear in the
front panel display. When this unit completes the
scan, “FINISH” and the number of receivable DAB
services appear in the front panel display, and then
this unit enters the DAB tuning mode automatically.
Scanning 30%
y
When you have already performed the initial scan before
you set this unit to the DAB tuning mode for the first time,
“Initiate Scan” does not appear in the front panel display.
See step 3 on page 49, and proceed with the DAB tuning
operation.
FINISH
[015]
BBC Radio 4
y
When you want to cancel the initial scan in the middle, press
RETURN.
Notes
• If the initial scan operation is not successful, “Not
Available” appears in the front panel display. You can start
the initial scan again by pressing k / n / l / h.
• For further details about problems and their proper
remedies, see the “DAB” section in “Troubleshooting” on
page 116.
48 En
DAB (Digital Audio Broadcasting)
When you select PRESET, the PRESET indicator
lights up in the front panel display.
DAB tuning
For DAB tuning, you do not tune in by station frequency
(like FM/AM), but tune in via the channel label instead.
There are five DAB tuning modes: ALPHANUMERIC,
ACTIVE, ENSEMBLE, FAVOURITE, and PRESET.
PRESET
y
Lights up
The SECONDARY indicator lights up when this unit is receiving
a DAB subchannel and turns off when the DAB subchannel
broadcast ends.
Important
Before tuning into any DAB services, you must perform
the initial scan (see “INIT SCAN” on page 53) to create a
registry list of available ensembles and services in
advance.
1
Set the operation mode selector to TV/AV.
DAB tuning mode
Function
ALPHANUMERIC
Browse through the all registered
DAB services in alphanumeric
order (0-9, A-Z).
ACTIVE
Browse through all of the receivable
DAB services in alphabetical order.
ENSEMBLE
Browse through the registered
ensembles in the order of the
channel label size from the smallest
to the largest.
FAVOURITE
Browse through the top 10 userselected services.
PRESET
See page 51.
TV/AV
YSP
2
Press DAB to select DAB as the input source.
The DAB indicator lights up in the front panel
display.
y
DAB
4
Press
/
service.
to select a registered DAB
BASIC
OPERATION
If you press
/
just after selecting a DAB tuning
mode, you can tune into the top or bottom of the DAB
service list.
DAB
Lights up
ENTER
y
You can also press INPUT on the front panel repeatedly to
select DAB as the input source.
y
3
Press SEARCH to switch between the DAB
tuning modes.
SEARCH
Press
/
to move to the top of the DAB service list.
ALPHANUMERIC
ACTIVE
ENSEMBLE
English
FAVOURITE
PRESET
49 En
DAB (Digital Audio Broadcasting)
PRESET MEMORY
3b
The PRESET MEMORY mode is used to assign up to 99
preset numbers to DAB services.
1
2
Use the numeric buttons to enter a preset
number.
For example, to assign “56” to the current DAB
service:
Tune into the DAB service you would like to
assign a preset number to.
MY BEAM
5
Press MEMORY.
The MEMORY indicator flashes for about ten
seconds.
MY SUR.
6
PRESET 56
If the number entered already exists (i.e. already
assigned to a service), then the previous service is
replaced with the current service.
MEMORY
MEMORY
4
Flashes
PRESET 5_
Press MEMORY to assign the indicated
preset number to the current DAB service.
The MEMORY indicator turns off.
y
There are two ways to select a preset DAB service: either by
using
/
or the numeric buttons.
3a
Press
/
to browse through the
assigned preset DAB service numbers in the
registry list.
When not assigned, “EMPTY” appears next to the
number. Continue pressing the button until
“EMPTY” appears. You can also choose the assigned
preset number. In this case, the previous service is
replaced with the current service.
ENTER
55 EMPTY
Appears on the front panel display
y
Press
50 En
/
to move to the top of the DAB service list.
MEMORY
y
You can also press ENTER to assign the indicated preset
number.
DAB (Digital Audio Broadcasting)
■ PRESET tuning
With PRESET tuning, you can tune into DAB services by
entering the assigned preset DAB service number.
1
Switch to DAB reception and select PRESET
as the tuning mode by following steps 1
through 3 as described in “DAB tuning” on
page 49.
If there is no service assigned to the preset numbers
entered, the numbers entered followed by “EMPTY”
appears in the front panel display for one second. The
service currently being broadcast is then displayed.
For example, if the preset number “56” was not
assigned to a service:
56 EMPTY
Appears for one second
y
There are two ways to select a preset DAB service: either by
using
/
or the numeric buttons.
2a
50 BBC Radio 2
Press
/
to browse through the preset
DAB services in the registry list.
Only the assigned preset numbers (along with the
services) appear; unassigned preset numbers are
skipped.
Current service being broadcast
ENTER
56 BBC Radio 4
BASIC
OPERATION
Appears for three seconds
BBC Radio 4
2b
Use the numeric buttons to enter a preset
service number.
For example, to select the preset DAB service
numbered “56”:
MY BEAM
5
MY SUR.
6
PRESET 5_
PRESET 56
Note
For numbers less than 10, simply press ENTER followed by
the number.
English
51 En
DAB (Digital Audio Broadcasting)
y
DAB service information
The DISPLAY key shows various information about the
service currently being broadcast.
y
A letter that cannot be displayed in the front panel display is
displayed as “_” (underscore).
Note
Up to 16 characters can be displayed in the front panel display at
one time. If there are more than 16 characters in the data text, the
information being displayed continuously scrolls from left to
right, one letter at a time.
1
While a service is currently being broadcast,
press DISPLAY.
DISPLAY
DLS (Dynamic Label Segment)
Displays information about the program currently
being broadcast. The current song or program title,
artist or speaker, or even what the next song or
program will be may be displayed. This data is
continuously updated by the DAB broadcaster, thus it
often changes (with every new song or program).
Other data, such as news, weather, and sports
headlines may be broadcast as well.
Date and time
Displays the current date and time. This data is
updated with each passing minute.
p
p
[ ]/[ ]:SERVICE
Each time you press DISPLAY, information about the
service being broadcast is displayed in the OSD and
front panel.
The service information is displayed in the following
order:
Example
1
Service label
Classic FM
2
DLS
Classic FM on
the internet...
3
Ensemble label
Digital1 Network
4
Program type
Classic Music
5
Date and time
01 JUL 07 10:30
6
Audio mode / bit rate
Stereo 160Kbps
7
Channel label /
frequency
11D / 222.06MHz
8
Signal quality
SIGNAL Q:100
The information order starts from the beginning again
after the information on signal quality has been
displayed.
52 En
Service label
Displays the name of the current service (maximum
16 letters).
Program type
Displays the genre (song/program type) of the current
service (maximum 16 characters).
ALPHANUMERIC
SERVICE:Classic FM
PROGRAM:Classic Music
DLS
:(Classic FM on t)
DISPLAY MODE
SERVICE:Classic FM
Information type
Descriptions of the information types are listed
below:
Ensemble label
Displays the name of the current ensemble
(maximum letters).
DAB INFORMATION
Order
You can set the time for which the DAB service information
is displayed on the video monitor by using the “OSD
DISPLAY TIME” on page 93.
Audio mode/bit rate
Displays the audio mode and bit rate of the current
service. There are 3 types of audio modes: Mono,
Stereo, and Dual. The range of bitrates is from 32
kbps to 256 kbps.
Channel label/frequency
Displays the channel label and frequency of the
current service.
Signal quality
Displays the signal strength (from 00 to 100) of the
current service. A higher number means better
reception.
DAB (Digital Audio Broadcasting)
Accessing DAB MENU
You can use the DAB MENU to adjust the DAB tuner
parameters and ensemble/service registry list. There are
five operations in DAB MENU: INIT SCAN, TUNE AID,
DRC MODE, PRUNE LIST, and PRESET DELETE.
y
Press RETURN to return to the previous menu level.
1
2
Switch to DAB reception by following steps 1
to 2 as described in “DAB tuning” on
page 49.
Press MENU.
“INIT SCAN” appears in the front panel display.
INIT SCAN
INIT SCAN locates all of the DAB ensembles and
services in your area. When this operation is selected, this
unit scans the entire band and creates a registry list of
every receivable DAB ensemble and service.
Important
You must perform this scan during the initial setup of this unit
before tuning into any DAB services.
■ Selective initial scan
1
MENU
INIT SCAN
Access DAB MENU by following steps 1
through 4 as described in “Accessing DAB
MENU” on this page.
“INIT SCAN” appears in the front panel display.
INIT SCAN
3
Press
/
to select a DAB operation.
ENTER
2
Press ENTER to select an operation.
The “SCAN?[ENTER]” verification message appears
in the front panel display if an initial scan mode is
selected. (The unit immediately returns to the DAB
MENU if SCAN:NO is selected.)
4
SCAN?[ENTER]
Press ENTER to access the selected DAB
operation.
BASIC
OPERATION
ENTER
ENTER
DAB MENU
.INIT SCAN
TUN AID
DRC MODE
PRUNE LIST
PRESET DELETE
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
English
53 En
DAB (Digital Audio Broadcasting)
3
Press ENTER to confirm your selection.
ENTER
The unit begins scanning the selected band(s) for
DAB ensembles.
• During the scan, “Scanning” appears in the front
panel display.
• When the scan has been completed, “FINISH”
appears in the front panel display, followed by the
number of a receivable DAB service.
“FINISH [###]” is displayed for three seconds.
TUNE AID
TUNE AID displays the strength of the DAB signal being
received by this unit in the front panel display. Use TUNE
AID to adjust the positioning of the indoor DAB antenna
and this unit and discover which setup has the best
reception state. It is recommended that you use TUNE
AID when setting up this unit in order to maximize DAB
reception ability.
1
Access DAB MENU by following steps 1
through 4 as described in “Accessing DAB
MENU” on page 53.
“INIT SCAN” appears in the front panel display.
INIT SCAN
Scanning xx%
2
Press
once.
“TUNE AID” appears in the front panel display.
FINISH [015]
(Example: if 15 services were found.)
ENTER
TUNE AID
After three seconds, this unit returns to the DAB
tuning mode automatically.
BBC Radio 4
If the INIT SCAN operation was not successful, “Not
Available” appears in the front panel display.
3
FINISH [000]
Press ENTER.
The signal strength level of the selected channel
appears in the front panel display. The signal strength
ranges from 00 (none) to 100 (best).
ENTER
Not Available
11B / LEVEL: 80
y
See the DAB section in “Troubleshooting” for further
details or proper remedies (see page 116).
4
If there are no preset DAB services, “Initiate Scan” or
“Not Available” appears in the front panel display.In this
time, press
/
to start INIT SCAN automatically.
Press / to switch to another channel
label.
The signal strength level of the new channel appears in
the front panel display. For a list of DAB frequencies,
see “DAB frequency table” on page 119.
ENTER
5
Press ENTER to exit from TUNE AID.
The unit returns to the TUNE AID menu display.
ENTER
54 En
11C / LEVEL: 40
TUNE AID
DAB (Digital Audio Broadcasting)
DRC MODE
4
Dynamic range is the decibel (dB) range between the
highest and lowest sounds in a broadcast. Some DAB
broadcasters transmit a wide dynamic range (enabling
high quality sound), accompanied by DRC (Dynamic
Range Control) data. DRC can be used to compress the
dynamic range of the broadcast, making softer sounds
easier to hear. This is especially useful when listening to a
DAB service in a noisy environment or at a low volume
(such as at night).
1
Access DAB MENU by following steps 1
through 4 as described in “Accessing DAB
MENU” on page 53.
“INIT SCAN” appears in the front panel display.
Press
or
ENTER
DRC MODE:AUTO
Operation mode
Function
DRC MODE: AUTO
Utilizes the DRC data (if
transmitted). The dynamic range of
the signal is compressed, enhancing
the audio quality at low volumes or
in a noisy environment.
DRC MODE: OFF
Does not utilize DRC data (if
transmitted). The dynamic range of
the signal is played in full, enabling
high sound quality.
If you select DRC MODE:AUTO and the broadcast
contains DRC data, then the DRC indicator lights up
in the front panel display.
Press
twice.
“DRC MODE” appears in the front panel display.
ENTER
to switch between AUTO and OFF.
DRC MODE:OFF
INIT SCAN
2
/
DRC
DRC MODE
Lights up
Press ENTER.
The DRC MODE option appears in the front panel
display.
Press ENTER.
The unit returns to the DRC MODE menu display.
ENTER
ENTER
BASIC
OPERATION
5
3
DRC MODE
DRC MODE:OFF
English
55 En
DAB (Digital Audio Broadcasting)
PRUNE LIST
PRESET DELETE
Use PRUNE LIST to delete a group of inactive ensembles
and services from the DAB registry list.
Use PRESET DELETE to delete specific unnecessary
services from the DAB registry list.
1
1
Access DAB MENU by following steps 1
through 4 as described in “Accessing DAB
MENU” on page 53.
“INIT SCAN” appears in the front panel display.
Access DAB MENU by following steps 1
through 4 as described in “Accessing DAB
MENU” on page 53.
“INIT SCAN” appears in the front panel display.
INIT SCAN
2
Press
three times.
“PRUNE LIST” appears in the front panel display.
ENTER
3
INIT SCAN
2
PRUNE LIST
Press ENTER.
The “OK? [ENTER]” verification message appears in
the front panel display.
Press
four times.
“PRESET DEL” appears in the front panel display.
ENTER
3
Press ENTER.
“DELETE:--” appears in the front panel display.
ENTER
ENTER
Press ENTER to confirm your selection.
Unnecessary services are deleted from the registry
list. Once this operation has been completed,
“FINISH” appears in the front panel display for one
second.
Press / .
Select the setting number of the service you wish to
remove. Only the preset number appears in the front
panel display.
ENTER
ENTER
DELETE:--
OK? [ENTER]
4
4
PRESET DELETE
DELETE:56
FINISH
5
The unit returns to the PRUNE LIST menu display.
PRUNE LIST
Press ENTER to confirm your selection.
The selected service is deleted from the registry list.
When this operation has been completed, “DELETE
OK” appears in the front panel display for one second.
ENTER
DELETE OK
The unit returns to the PRESET DELETE menu
display.
PRESET DELETE
56 En
USING IPOD™
Using iPod™
This unit has the DOCK terminal on the rear panel that allows you to connect the Yamaha iPod universal dock (such as
YDS-10, sold separately). Station your iPod in the Yamaha iPod universal dock, and use the supplied remote control to
operate your iPod.
Notes
• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
Connection
Controlling iPod™
Connect the Yamaha iPod universal dock to the DOCK
terminal of this unit using a dedicated cable.
STANDBY/ON
POWER POWER
AV
CAUTION
TV
DOCK
DVD
Do not connect this unit or other components to the main power
until all connections between components are complete.
AUX1
0
ENHANCER
Rear panel of this unit
AUX2
AUX3
TV
INPUT1 MACRO
STB
OFF
TV
+10
ENTRY
MENU
1
TV/AV
ENTER
ANTENNA
AUDIO INPUT
OUT
VIDEO
DIGITAL INPUT
AUX 2
DVD
COAXIAL
YSP
2
DISPLAY
OPTICAL
DOCK
AUX 1 TV/STB SUBWOOFER
AUX1
3
SUR. DECODE
RETURN
VOLUME
CH
MUTE
TV INPUT
4
5
6
TV VOL
TV/STB
TEST
BASIC
OPERATION
CH LEVEL
TV MUTE
CODE SET
7
8
9
0
Yamaha iPod universal dock
(such as YDS-10, sold separately)
A
y
When your iPod and external component using the AUX 3 input
jack are connected to this unit at the same time, and when the
DOCK indicator is lit in the front panel display, iPod output takes
priority.
1 Navigate through the iPod menu (
/
/
and starts playback (ENTER).
2 Displays the OSD (on-screen menu) menu.
/
)
3 Selects AUX3/DOCK as the input source.
4 Use to return to the previous iPod menu.
5 Sets the operation mode of this unit.
6 Use to return to the previous iPod menu.
7 Stops playback.
8 Pauses playback.
9 Searches forward/backward.
0 Starts playback.
8 and 9 toggle between play and pause operations in the Simple
Remote mode.
57 En
English
A Skips to the beginning of the current/previous/next
track.
y
Using iPod™
y
• For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in
“Troubleshooting” on page 116.
• While your iPod is stationed in the Yamaha iPod universal dock connected to the DOCK terminal of this unit, your iPod battery is
automatically charged as long as this unit is turned on.
■ Controlling iPod in the Simple Remote
mode
■ Controlling iPod in the Menu Browse
mode
You can perform some basic operations such as play,
pause, stop, backward/forward search, and track skip
using the remote control without the aid of the OSD. Such
basic operations can be performed also on your iPod.
You can perform the advanced operations using the remote
control with the aid of the OSD. In the OSD, you can
browse the song list stored on your iPod. Further, you can
change or adjust the settings on your iPod as desired. Such
advanced operations cannot be performed on your iPod.
1
Set the operation mode selector to TV/AV.
1
Set the operation mode selector to TV/AV.
TV/AV
YSP
TV/AV
YSP
2
Press AUX3/DOCK and set your iPod in the
Yamaha iPod universal dock.
In the front panel display, “iPod connected” appears
and the DOCK indicator lights up.
2
Press AUX3/DOCK and set your iPod in the
Yamaha iPod universal dock.
In the front panel display, “iPod connected” appears
and the DOCK indicator lights up.
Lights up
Lights up
iPod connected
iPod connected
y
• You can view the photos or video clips stored on your iPod.
However, you cannot view the OSD that appears only in the
iPod screen.
• Use # and * on the remote control interchangeably to toggle
between play and pause operations.
3
Press DISPLAY, and display the menu
browse mode.
The OSD appears on your TV.
Note
Information on the current song appears only in the iPod screen
but not in the front panel display of this unit.
58 En
iPod
DISPLAY
Top
Playlists
Artists
Albumss
Songsts
Genress
Composerss
Settings
>
>
>
>
>
>
>
Using iPod™
y
4
Press
/
and / to navigate through
the iPod menu, and press ENTER to start
playback of the selected song.
ENTER
and
ENTER
• Press RETURN or MENU to go back to the previous menu.
• The information on the current song also appears in the front
panel display. You can set the front panel display mode: CONT.
or ONCE. For details, see “SCROLL” (Front panel display
scroll) in “F.DISPLAY SET” (Front panel display settings) (see
page 92).
• You can set the interval for which the OSD screen is displayed
after an operation. See “OSD DISPLAY TIME” (OSD display
time) in “OSD SET” (OSD settings) (see page 93).
Notes
ENTER
Choices: Playlists (playlists), Artists (artists), Albums
(albums), Songs (songs), Genres (genres),
Composers (composers), Settings (settings)
• Playlists > Songs
• Artists > Albums > Songs
• Albums > Songs
• Songs
• Genres > Artists > Albums > Songs
• Composers > Albums > Songs
• Settings > Shuffle, Repeat
• The Yamaha logo appears in the iPod screen in this mode.
• Undisplayable characters are shown as underscores “_” in the
front panel display and OSD.
• You can change or adjust the “Settings” parameters only in the
OSD.
• You cannot view the photos or video clips stored on your iPod
in this mode. Use the Simple Remote mode to enjoy browsing
the photos or video clips stored on your iPod.
■ An example of the information display
during playback
7
Shuffle Shuffle
Use this function for random playback of songs or albums.
When “Songs” or “Albums” is chosen, “S” appears in the
top right corner while the songs or albums are being
shuffled. Press ENTER repeatedly to toggle between the
choices.
Choices: Off, Songs, Albums
• Select “Off ” to deactivate this function.
• Select “Songs” for random playback of songs.
• Select “Albums” for random playback of albums.
Repeat Repeat
Use this function for repeated playback of a song or a
sequence of songs. When “One” or “All” is chosen, “R”
appears in the top right corner while a song or a sequence
of songs are being repeated. Press ENTER repeatedly to
toggle between the choices.
Choices: Off, One, All
• Select “Off ” to deactivate this function.
• Select “One” for repeated playback of a song.
• Select “All” for repeated playback of a sequence of
songs.
2
3
4
FrankieZipper
Made-to-order
RoadtoIndia
5
6
||||||||;;;;;;;;;;;;
0:51-7:44
8
9
1 Track number/total tracks
BASIC
OPERATION
Settings parameters:
1
iPod[Play]
S R
1/9
2 Name of the artist
3 Name of the album
4 Name of the song
5 Progress bar
6 Elapsed time
7 Shuffle and repeat icons
8
(playback),
(pausing),
and
(search backward)
(search forward),
9 Remaining time
English
59 En
ENJOYING SURROUND SOUND
Enjoying surround sound
You can enjoy multi-channel surround sound by changing the beam mode using the beam mode buttons on the remote
control. Select 5 Beam, Stereo plus 3 Beam, 3 Beam, or My Surround for multi-channel playback.
Notes
• When ANGLE TO WALL OR CORNER is set in MANUAL SETUP (see page 82), 5 Beam and 3 Beam cannot be selected.
• To enjoy 5 Beam, Stereo plus 3 Beam, or 3 Beam as the beam mode, you must perform AUTO SETUP or MANUAL SETUP so that
the parameters best match your listening environment.
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
1
2
3BEAM
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
9
SUR. DECODE
+10
ENTRY
MENU
5 Beam
Outputs sound beams from the front left, front right,
center, surround left, and surround right channels. This
mode is ideal for enjoying surround sound effects to the
fullest when you watch DVDs recorded in a multi-channel
format or play back 2-channel sources in a multi-channel
format.
Press 5BEAM to select 5 Beam.
TV/AV
ENTER
YSP
DISPLAY
RETURN
5BEAM
1
1
Set the operation mode selector to YSP.
TV/AV
Notes
YSP
2
Press one of the beam mode buttons
(5BEAM, ST+3BEAM, 3BEAM, or MY SUR.) to
select the desired beam mode for 5.1channel play back.
5BEAM
ST+3BEAM
3BEAM
1
2
3
MY SUR.
6
60 En
• To achieve the best surround sound effect, make sure that there
are no obstacles placed in the path of sound beams in that the
objects may prevent the sound beams from rebounding directly
off the walls in your listening room.
• The front left and right sound beams are output toward the walls
in your listening room.
• “SP Pos. Corner!” appears in the front panel display if
INSTALLED POSITION is set to ANGLE TO WALL OR
CORNER (see page 82).
Enjoying surround sound
Stereo plus 3 Beam
Outputs normal sound from the front left and right
channels and sound beams from the center and surround
left and right channels. This mode is ideal for watching
live recordings on a DVD. Vocals and instrumental sounds
can be heard close to the center of the listening position
while sound reflections from the venue itself can be heard
on your right and left, giving you the feeling that you are
sitting right in front of the stage.
Press ST+3BEAM to select Stereo plus 3 Beam.
Notes
• When you play back multi-channel sources, surround left and
right signals are mixed down and output from the front left and
right channels.
• The front left and right sound beams are output toward the walls
in your listening room.
• “SP Pos. Corner!” appears in the front panel display if
INSTALLED POSITION is set to ANGLE TO WALL OR
CORNER (see page 82).
My Surround
ST+3BEAM
2
This mode enables surround system in a small listening
area which may not fulfill the listening room conditions
for other beam modes (see “Before installing this unit” on
page 14). Use this beam mode when you want to enjoy
surround sound near this unit, or when the other beam
modes are unavailable.
Press MY SUR. to select My Surround.
MY SUR.
6
Note
The front left and right sound beams are output directly toward
the listening position.
BASIC
OPERATION
3 Beam
Outputs sound beams from the front left and right and
center channels. This mode is ideal for enjoying movies
with the whole family. Because the listening position area
is widened, you can enjoy excellent quality surround
sound over a wider area. In addition, you can use this
mode when the listening position is close to the backside
of the wall, and the surround left and right sound beams
cannot be reflected off the wall.
Notes
• Beam mode settings such as beam angles and distances are
ineffective in this mode.
• For the full effect of My Surround, your listening position must
face toward the front of this unit.
Press 3BEAM to select 3 Beam.
3BEAM
3
English
y
You can achieve a more realistic surround effect if you adjust
settings for IMAGE LOCATION in BEAM MENU (see page 86).
61 En
Enjoying surround sound
■ Decoder indicators
Depending on the input source and the selected surround
mode, the indicators in the front panel display light up as
follows:
Status
When PCM signals are being input
Indicator
PCM
When DTS digital signals are being
input
■ Surround modes and recommended
sources
Recommended
source
Surround mode
Dolby Pro Logic
–
All sources
Dolby Pro Logic II
Movie
Music
Game
Movies
Music
Games
DTS Neo:6
Cinema
Music
Movies
Music
Notes
When DTS Neo:6 is selected as the
surround mode
When Dolby Digital signals are
being input
When Dolby Pro Logic is selected
as the surround mode
When Dolby Pro Logic II is selected
as the surround mode
+
DIGITAL
PL
PL
y
• You can select an input mode (AUTO, DTS, or ANALOG) by
pressing INPUTMODE repeatedly (see page 97).
• Discs encoded in DTS-ES, Dolby Digital 5.1 EX, Dolby Digital
EX, or Dolby Digital Surround EX will be played back in DTS
or Dolby Digital.
■ Input channel indicators
Depending on the channel component of the current
digital input signal, the input channel indicators in the
front panel display light up as follows:
Status
When 2-channel stereo signals are
being input
When 5.1-channel signals are being
input
62 En
Indicator
• When you select an input source (see page 44), the surround
mode used for the previously selected input source is
automatically selected.
• If the power of this unit is turned off and on again, the surround
mode used for the previously selected input source before the
power was turned off is automatically selected.
• If the surround modes are not available, “Prohibit” appears in
the front panel display when you press SUR. DECODE.
• The surround modes are available:
– when the beam mode is set to a setting other than the 2channel or 5-channel stereo playback (see page 66) and My
Surround (see page 61).
– when the CINEMA DSP programs are turned off
(see page 73).
– when the movie program is selected as the CINEMA DSP
program (see page 72). In this case, only Dolby Pro Logic,
Dolby Pro Logic II Movie, and DTS Neo:6 Cinema are
available.
– when 2-channel signals are being input.
– when the Music Enhancer is turned off (see page 74).
Enjoying surround sound
Enjoying 2-channel sources
in surround sound
This unit can decode 2-channel sources for 5.1-channel
playback so that you can enjoy a variety of surround sound
effects by switching the surround mode.
2
Press SUR. DECODE repeatedly (or press
SUR. DECODE and then press / ) to
switch between surround modes.
Choices: Neo:6 Cinema, Neo:6 Music, PRO LOGIC,
PLII Movie, PLII Music, PLII Game
Default setting: Neo:6 Cinema
y
The surround modes are available only when the CINEMA DSP
programs are turned off (see page 73) or when the movie program
is selected as the CINEMA DSP program (see page 72). In
addition, the beam mode must be set to 5 Beam, Stereo plus 3
Beam, or 3 Beam (see page 60), while the Music Enhancer must
be also turned off (see page 74).
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
or
SUR. DECODE
ENTER
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
SUR. DECODE
9
SUR. DECODE
+10
0
ENHANCER
ENTRY
MENU
Neo:6 Cinema
TV/AV
ENTER
YSP
DISPLAY
RETURN
Neo:6 Music
PRO LOGIC
Set the operation mode selector to YSP.
TV/AV
PLII Movie
BASIC
OPERATION
1
PLII Music
YSP
PLII Game
Example of the surround
mode display in the front
panel display when the
CINEMA DSP program
and the Music Enhancer
are turned off
English
63 En
Enjoying surround sound
Enjoying TV in surround sound
4
If you hear sound from your TV speakers,
reduce the volume level of your TV until you
can no longer hear any audio being output.
To reduce the TV volume level, use the remote
control supplied with your TV.
5
Press VOLUME +/– to adjust the volume
level.
You can enjoy analog audio signals output from your TV
in real surround sound.
y
Before performing the steps below, set the volume of this unit to
30. If necessary, adjust the volume level in step 4 below.
TV
INPUT1 MACRO
TV
STB
SEARCH
MEMORY
DAB
VOLUME
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
1
2
3BEAM
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
9
SUR. DECODE
+10
0
ENHANCER
ENTRY
MENU
TV/AV
ENTER
YSP
DISPLAY
RETURN
VOLUME
CH
TV VOL
6
Press SUR. DECODE repeatedly (or press
SUR. DECODE and then press / ) to
switch between surround modes.
Signals input from 2-channel sources are played back
in multi-channels.
For more information on surround modes, see
page 62.
SUR. DECODE
1
Select the TV channel you want to watch.
To select a TV channel, use the remote control
supplied with your TV.
or
SUR. DECODE
2
Set the operation mode selector to YSP.
TV/AV
YSP
3
Press TV.
This unit outputs audio signals from your TV.
TV
64 En
ENTER
Enjoying surround sound
Adjusting surround mode
parameters
You can configure the parameters for Dolby Pro Logic II
Music and DTS Neo:6 Music to fine-tune the surround
sound effect.
MUSIC
MOVIE
7
8
OFF
0
ENHANCER
SPORTS
+10
ENTRY
MENU
TV/AV
YSP
DISPLAY
RETURN
1
Repeat steps 1 and 2 in “Enjoying 2-channel
sources in surround sound” on page 63 and
select PL II Music or Neo:6 Music.
2
Press
to select the parameter.
ENTER
DIMENSION
Adjusts the difference in volume between the front
and surround channels to the desired volume balance.
Control range: –3 (toward the surround direction) to
+3 (toward the front direction)
Default setting: STD (standard)
C. WIDTH
Distributes the center channel sound to the left and
right. If 0 is selected, the center channel sound is
output only from the center channel.
Control range: 0 to 7
Default setting: 3
■ When DTS Neo:6 Music is selected
C. IMAGE
Adjusts the center image from three channels (front
left and right and center) to varying degrees.
Control range: 0.0 (wider) to 1.0 (toward the center)
Default setting: 0.3
Press / to configure the selected
parameter.
BASIC
OPERATION
3
PANORAMA
Gives the front left and right channel sound a
wraparound effect, distributed throughout the entire
surround sound field to give you an expansive feeling.
Choices: ON/OFF
Default setting: OFF
9
SUR. DECODE
ENTER
/
■ When Dolby Pro Logic II Music is
selected
ENTER
English
65 En
ENJOYING STEREO SOUND
Enjoying stereo sound
You can enjoy 2-channel and 5-channel stereo playback as the beam modes by pressing STEREO on the remote control.
Notes
• When you play back Dolby Digital audio signals in the 2-channel or 5-channel stereo playback, the dynamic range becomes
compressed. If the volume level decreases to the extreme, use other beam modes except My Beam.
• When the 2-channel or 5-channel stereo playback is selected as the beam mode, the surround modes (see page 62) and the CINEMA
DSP programs (see page 69) become ineffective.
Note
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
9
SUR. DECODE
+10
ENTRY
When you play back multi-channel sources, all signals except
those from the front left and right channels are mixed down and
output from the front left and right channels. No audio is output
from the center and surround channels.
MENU
TV/AV
ENTER
5-channel stereo playback
YSP
DISPLAY
RETURN
2-channel stereo playback
Sounds are output from front left and right, center, and
surround left and right. This is ideal for playback in a large
listening area or at a party.
Sounds are output from the front right and left channels.
This is ideal for playing back hi-fi sources, such as CDs,
and can be used to replace your TV speakers.
1
Set the operation mode selector to YSP.
TV/AV
YSP
1
Set the operation mode selector to YSP.
TV/AV
YSP
2
Press STEREO to select the 2-channel stereo
playback as the beam mode.
“STEREO” appears in the front panel display.
2
Press STEREO twice to select the 5-channel
stereo playback as the beam mode.
“5CH STEREO” appears in the front panel display.
STEREO
4
STEREO
4
5CH STEREO
STEREO
66 En
PLAYING BACK SOUND CLEARLY (MY BEAM)
Playing back sound clearly (My Beam)
You can improve listenability in a noisy environment by changing the beam mode to My Beam, which outputs sound
beams directly toward the listening position in a single channel. In addition, My Beam is also ideal when you do not want
the sound beams to be reflected on the walls in your listening room or when you do not want to disturb other people
while enjoying music or movies at night.
My Beam
microphone
STANDBY/ON
POWER POWER
AV
TV
5BEAM
ST+3BEAM
1
2
3BEAM
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
9
SUR. DECODE
+10
0
ENHANCER
ENTRY
MENU
TV/AV
ENTER
YSP
DISPLAY
RETURN
Note
Using auto-adjust function
The My Beam microphone on the remote control collects
the test tones from this unit so that the beam angle can be
automatically adjusted.
1
Set the operation mode selector to YSP.
TV/AV
YSP
2
Press and hold MY BEAM for more than two
seconds.
A test tone is output twice from this unit. Keep
pointing the remote control toward this unit while the
test tones are being output so that the My Beam
microphone can collect the test tones.
Control range: L60° to R60°
Operation guarantee range: 6 m (20 ft), L45° to R45°
Notes
BASIC
OPERATION
If My Beam is selected as the beam mode, the surround modes (see page 62), the CINEMA DSP programs (see page 69), and TruBass
(see page 88) become ineffective. In addition, no audio is output from the subwoofer connected to this unit.
• If an error occurs, an error buzzer is played and “MY BEAM
ERROR” is displayed in the front panel display.
• An error may occur if the listening room is noisy. Make sure
that the listening room is as quiet as possible while the test
tones are being output.
• Do not shake or move the remote control while the test tones are
being output.
• Do not cover the My Beam microphone on the remote control
while the test tones are being output.
• The batteries in the remote control may be weak if the remote
control does not function properly. In this case, replace all the
batteries and then try the procedure again.
• When the input signal with 64 kHz or 96 kHz of sampling
frequency is being played back, the beam angle cannot be
automatically adjusted.
English
MY BEAM
5
67 En
Playing back sound clearly (My Beam)
Using manual-adjust function
You can adjust the beam angle manually while playing
back an input source. This function is also ideal if the
listening position is out of the operation guarantee range
of the auto-adjust function.
1
Set the operation mode selector to YSP.
TV/AV
YSP
2
Press MY BEAM.
“MY BEAM” is displayed in the front panel display.
MY BEAM
5
3
Press / while “MY BEAM” is displayed to
adjust the beam angle.
Control range: L90° to R90°
• Press repeatedly to increase the horizontal angle
on the left side.
• Press repeatedly to increase the horizontal angle
on the right side.
ENTER
ANGLE
68 En
0
USING SOUND FIELD PROGRAMS
Using sound field programs
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from
stereo or multi-channel sources. This unit is also equipped with a Yamaha CINEMA DSP (digital sound field processing)
chip containing several sound field programs used to enhance your playback experience. Most of the CINEMA DSP
programs are precise digital recreations of actual acoustic environments found in famous concert halls, music venues, and
movie theaters.
y
The Yamaha CINEMA DSP programs are compatible with all Dolby Digital, DTS, and Dolby Surround sources.
Note
Choose a CINEMA DSP program based on your listening preference and do not purely rely on the name of the CINEMA DSP program
itself.
■ What is a sound field?
A significant factor that creates the rich, full tones of a live instrument is the multiple reflections from the walls of the
room. In addition to making the sound live, these reflections enable the listener to tell where the player is situated as well
as the size and shape of the room in which the listener is sitting.
■ Elements of a sound field
In any environment, there are two distinct types of sound reflections combined with the direct sound coming straight to
our ears from the player’s instrument to make up the sound field.
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms to 80 ms after the direct sound) after reflecting from one
surface only (from the ceiling or the wall, for example). Early reflections help add clarity to the direct sound.
Direct sound, early reflections, and subsequent reverberations all together help us determine the subjective size and shape
of the room, and it is this information that the digital sound field processor reproduces in order to create the sound fields.
BASIC
OPERATION
Reverberations
These are caused by reflections from more than one surface (i.e., wall, ceiling, the back of the room, etc.) so numerous
that they merge together to form a continuous sonic afterglow. They are non-directional and lessen the clarity of the direct
sound.
With the appropriate early reflections and subsequent reverberations in your listening room, you can create your own
listening environment. The acoustics in your room could be changed to those of a concert hall, a dance floor, or a
listening room of virtually any size at all. This ability to create sound fields at will is exactly what Yamaha has done with
the CINEMA DSP technology.
English
69 En
Using sound field programs
■ Sound field program descriptions
You can select from the following sound field programs based on your listening preference when you play music, movie
or sports sources. For details on how to switch between the available sound field programs, see page 71.
Note
There is only one sports sound field program available.
Sound field program
Feature
Music Video
This program produces a vibrant environment and lets you feel as if
you are at an actual jazz or rock concert.
Concert Hall
This program creates a rich surround effect of a large round concert
hall with a great deal of presence, emphasizing the extension of
sounds, and lets you feel as if you are seated close to the center of the
stage.
Music
Jazz Club
This program recreates the acoustic environment of “The Bottom
Line”, a famous jazz club in New York and lets you feel as if you are
seated right in front of the stage.
Sci-Fi
This program clearly reproduces dialogs and special sound effects of
the latest science fiction films and lets you feel a broad and expansive
cinematic space amid silence.
Spectacle
70 En
Source
Movie
This program reproduces the wide and grand environment and lets you
have added impressions on spectacular scenes with strong visual
impacts.
Adventure
This program reproduces the thrilling environment of the latest action
films and lets you feel the dynamic and excitement of fast-moving
scenes.
SPORTS
This program reproduces the energetic environment of live sports
broadcasting, converging a commentator’s voice on the center and
broadening the overall atmosphere of the stadium, and lets you feel as
if you are seated at an actual stadium or a ball park.
Sports
Using sound field programs
CINEMA DSP programs
You can select from three different CINEMA DSP
programs (MUSIC, MOVIE, and SPORTS) depending on
the type of source you want to enjoy. The CINEMA DSP
indicator lights up in the front panel display when one of
the CINEMA DSP programs is selected.
■ Music programs
Select this CINEMA DSP program when you play back
music sources. This program produces a vibrant
atmosphere and lets you feel as if you are seated in an
actual rock or jazz concert hall.
1
Set the operation mode selector to YSP.
Notes
TV/AV
• The CINEMA DSP programs are ineffective when My
Surround (see page 61) is selected as the beam mode.
• If the CINEMA DSP programs are not available, “Prohibit”
appears in the front panel display when you press one of the
CINEMA DSP program buttons on the remote control.
YSP
2
Press MUSIC to select the music CINEMA
DSP program.
MUSIC
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
9
SUR. DECODE
7
3
+10
ENTRY
MENU
TV/AV
ENTER
Check that MUSIC is displayed in the front
panel display and then press MUSIC on the
remote control repeatedly (or press / on
the remote control) to switch between the
music sound field programs.
YSP
DISPLAY
RETURN
MUSIC
7
BASIC
OPERATION
MUSIC
ENTER
or
Music Video
Concert Hall
Jazz Club
y
For detailed descriptions of each sound field program, see “Sound
field program descriptions” on page 70.
English
71 En
Using sound field programs
■ Movie programs
■ Sports program
Select this CINEMA DSP program when you play back
movie sources, especially the ones encoded in Dolby
Digital, DTS, or Dolby Surround. This program clearly
reproduces dialog and sound effects, thus creating a broad
and expansive cinematic space amid silence.
Select this CINEMA DSP program when you play back
sports sources. This program densely concentrates the
vocal sound of the commentator in the center while
broadening the sound from the audience or the
environment all around your listening room.
1
1
Set the operation mode selector to YSP.
TV/AV
TV/AV
YSP
YSP
2
3
2
Press MOVIE to select the movie CINEMA
DSP program.
SPORTS
8
9
MOVIE
MOVIE
ENTER
or
Sci-Fi
Spectacle
Adventure
y
For detailed descriptions of each sound field program, see “Sound
field program descriptions” on page 70.
72 En
Press SPORTS to select the sports CINEMA
DSP program.
MOVIE
Check that MOVIE is displayed in the front
panel display and then press MOVIE on the
remote control repeatedly (or press / on
the remote control) to switch between the
music sound field programs.
8
Set the operation mode selector to YSP.
SPORTS
y
• There is only one sports sound field program available.
• For detailed descriptions of each sound field program, see
“Sound field program descriptions” on page 70.
Using sound field programs
■ Turning off CINEMA DSP programs
Turn off the CINEMA DSP programs if you want to enjoy
the original sound without the CINEMA DSP program
effect.
2
Press MUSIC, MOVIE, or SPORTS to select
the desired CINEMA DSP program.
MUSIC
1
TV/AV
YSP
2
7
Set the operation mode selector to YSP.
3
MOVIE
or
8
SPORTS
or
9
Press
/
.
“DSP LEVEL” is displayed in the front panel display.
ENTRY
Press OFF to turn off the CINEMA DSP
programs.
“CINEMA DSP OFF” is displayed in the front panel
display and the CINEMA DSP indicator disappears.
ENTER
OFF
0
DSP LEVEL
0dB
CINEMA DSP OFF
4
Press / to adjust the effect level of the
selected CINEMA DSP program.
You can enjoy good quality sound with the factory preset
parameters. However, you can also adjust the effect level
of the CINEMA DSP programs relative to the level of the
direct sound so that each CINEMA DSP program can
reflect your listening environment and your preference
even more accurately.
1
Set the operation mode selector to YSP.
BASIC
OPERATION
■ Adjusting CINEMA DSP effect levels
ENTER
Control range: –6 dB to +3 dB
• A larger value increases the effect level.
• A smaller value decreases the effect level.
TV/AV
YSP
English
73 En
USING THE MUSIC ENHANCER
Using the music enhancer
You can use the Music Enhancer of this unit to improve the sound nearest to the original depth and width of compression
artifacts such as the MP3 format.
MUSIC
MOVIE
7
8
OFF
SPORTS
9
SUR. DECODE
+10
0
ENHANCER
ENTRY
3
Press ENHANCER repeatedly to switch
between the Music Enhancer levels (OFF,
MIN, and MAX).
MENU
ENHANCER
TV/AV
ENTER
YSP
DISPLAY
RETURN
VOLUME
CH
TV VOL
ENHANCER:HIGH
1
ENHANCER:LOW
Set the operation mode selector to YSP.
ENHANCER OFF
TV/AV
YSP
2
Press ENHANCER to select the Music
Enhancer.
The currently selected mode appears in the front
panel display.
The ENHANCER indicator lights up when
“ENHANCER:HIGH” or “ENHANCER:LOW” is
selected.
ENHANCER
Lights up
Notes
• The Music Enhancer is not compatible with the CINEMA DSP
programs. If a CINEMA DSP program is selected while the
Music Enhancer is on, the Music Enhancer is turned off
automatically. In this case, the Music Enhancer remains off
even after the CINEMA DSP program is canceled. Likewise, if
the Music Enhancer is turned on while a CINEMA DSP
program is selected, the CINEMA DSP program is canceled
automatically. In this case, the CINEMA DSP program remains
off even after the Music Enhancer is turned off.
• The Music Enhancer is available only when a setting other than
My Surround (see page 61) is selected as the beam mode.
74 En
USING THE VOLUME MODE (NIGHT LISTENING ENHANCER/TV VOLUME EQUAL MODE)
Using the volume mode
(Night listening enhancer/TV volume equal mode)
The night listening enhancers are designed to improve listenability at lower volumes or at night. In addition, you can limit
the volume level of the TV so that it will not vary suddenly to a great extent whenever the contents being broadcast
change (i.e. due to commercials, etc.).
The EQUAL indicator lights up in the front panel
display when “TV EQUAL VOLUME” is selected.
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
1
2
3BEAM
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
9
Lights up
SUR. DECODE
+10
ENTRY
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
to make dialog easier to hear at lower volumes.
• Select NIGHT:MUSIC when listening to music
sources to preserve ease-of-listening for all sounds.
• Select TV EQUAL VOLUME when watching TV
programs.
• Select OFF to turn off the volume mode.
MENU
TV/AV
ENTER
YSP
DISPLAY
1
RETURN
Set the operation mode selector to YSP.
TV/AV
YSP
Press VOL MODE repeatedly to select
NIGHT:CINEMA, NIGHT:MUSIC, TV EQUAL
VOLUME, or OFF.
Press / to adjust the effect level of
compression while NIGHT:CINEMA,
NIGHT:MUSIC, or TV EQUAL VOLUME is
displayed.
ENTER
VOL MODE
NIGHT:CINEMA
Effect.Lvl:MIN
NIGHT:MUSIC
Effect.Lvl:MID
TV EQUAL VOLUME
Effect.Lvl:MAX
OFF
The NIGHT indicator lights up in the front panel
display when “NIGHT:CINEMA” or
“NIGHT:MUSIC” is selected.
• Select Effect.Lvl:MIN for minimum compression.
• Select Effect.Lvl:MID for standard compression.
• Select Effect.Lvl:MAX for maximum
compression.
Notes
• The volume mode settings are canceled if you press
STANDBY/ON or disconnect the AC power supply cable from
the AC wall outlet.
• The volume mode settings become ineffective when My
Surround is selected as the beam mode (see page 61).
75 En
English
Lights up
BASIC
OPERATION
2
3
USING THE SLEEP TIMER
Using the sleep timer
Use this feature to automatically set this unit to the standby mode after a specified period of time. The sleep timer is
useful if you are going to sleep after a certain amount of time while this unit is still playing back a source.
SEARCH
Each time you press SLEEP, the front panel display
changes as shown below.
MEMORY
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
SLEEP
3BEAM
9
SUR. DECODE
+10
ENTRY
SLEEP
120min
SLEEP
90min
SLEEP
60min
SLEEP
30min
SLEEP
OFF
MENU
TV/AV
ENTER
YSP
DISPLAY
1
RETURN
Set the operation mode selector to YSP.
TV/AV
3
YSP
2
Press SLEEP repeatedly to set the interval
for the sleep timer.
Choices: 120min, 90min, 60min, 30min, OFF
The SLEEP indicator flashes in the front panel
display while switching the interval for the sleep
timer.
SLEEP
Flashes
76 En
Wait for a few seconds without operating this
unit to confirm the setting for the sleep timer.
The SLEEP indicator lights up in the front panel
display, indicating that the sleep timer is activated.
Lights up
Using the sleep timer
■ Canceling the sleep timer
1
Set the operation mode selector to YSP.
TV/AV
YSP
2
Press SLEEP repeatedly until “SLEEP OFF”
appears in the front panel display.
SLEEP
SLEEP
3
OFF
Wait for a few seconds without operating this
unit to confirm the setting for the sleep timer.
The SLEEP indicator disappears from the front panel
display, indicating that the sleep timer is deactivated.
Disappears
BASIC
OPERATION
Note
The previous setting for the sleep timer before you deactivate it is
stored in the system memory.
y
The sleep timer setting can also be deactivated if you press
STANDBY/ON to set this unit to the standby mode or unplug the
AC power supply cable from the AC outlet.
English
77 En
DISPLAYING THE INPUT SOURCE INFORMATION
Displaying the input source information
You can display the format and sampling frequency of the current input signal in the front panel display.
7
8
OFF
2
9
SUR. DECODE
+10
0
ENHANCER
ENTRY
MENU
Press DISPLAY.
The information on the current input signal is
displayed as follows:
DISPLAY
TV/AV
ENTER
YSP
DISPLAY
RETURN
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
D.DGTL:48kHz
or
1
Set the operation mode selector to YSP.
TV/AV
YSP
INPUT SIGNAL
DOLBY DGTL:48kHz
Input signal
Indicator
Dolby digital
DOLBY DGTL
DTS
DTS
PCM
PCM
Analog
ANALOG
Sampling
frequency
32/44.1/48/64/
88.2/96 kHz
–
y
When the input signal is unclear, “___” is displayed for the
sampling frequency.
78 En
USING THE HDMI CONTROL FEATURE
Using the HDMI control feature
You can operate the following functions using the remote control supplied with your TV if this unit and an HDMI
control-compatible TV (except some models) are connected via HDMI.
• Turning on or off the power (synchronized operation with the TV)
• Selecting the audio output component (TV or this unit)
• Adjusting the volume level (up/down and mute)
An example of the HDMI control-compatible component is a Panasonic Viera Link-compatible component (TV, DVD
recorder, Blu-ray recorder, etc.).
y
If you connect this unit to an HDMI control-compatible DVD player or Blu-ray Disc player via HDMI, you can also control the
connected component in synchronization with this unit (except some models).
Connect this unit to your HDMI control-compatible TV via HDMI.
For details about HDMI and HDMI components, see “Information on HDMI™” on page 18 and “Connections using
HDMI cables” on page 19. Also in the owner’s manual supplied with your TV, refer to the information on
connecting an AV amplifier.
2
Turn on the power of all components connected via HDMI.
For details about controlling external components, see the owner’s manuals supplied with your components.
3
Check the system settings for all components connected via HDMI and activate the HDMI control
feature.
For details about setting external components, see the owner’s manuals supplied with your components. Once you
have followed steps 1 to 3, you do not need to carry out the same procedure again next time.
4
Turn off the power of your TV and then turn on the power again.
5
Set the input source selector of your TV to this unit (HDMI, etc.).
6
Select the connected component as the input source by pressing INPUT on the front panel of this
unit (or press one of the input selector buttons on the remote control). Confirm that the video
image played back on the DVD recorder (etc.) appears in your TV correctly.
7
Use the remote control supplied with your TV to turn on or off the power, select the audio output
component, and adjust the volume level of this unit.
BASIC
OPERATION
1
Notes
• Check the following if you cannot operate this unit in synchronization with your TV.
– Whether HDMI CONTROL is set to ON (see page 91).
– Whether the HDMI control feature is activated for your TV (see the owner’s manual supplied with your TV).
• While you are playing back audio from a non-HDMI component, turning off the power of your TV with the remote control
supplied with your TV does not turn off the power of this unit. Playback continues without being affected.
English
79 En
MANUAL SETUP
MANUAL SETUP
To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment
parameters, as well as to make advanced settings for sound signals, sound beams, digital input, and the OSD. Change the
initial settings (indicated in bold under each parameter) to reflect the needs of your own listening environment.
y
• You can save the settings optimized by the AUTO SETUP procedure (see page 41). A set of settings optimized according to the
specific conditions of your listening environment can be recalled later depending on the varying conditions of your listening
environment (see page 42).
• Most of the parameters in SOUND MENU and BEAM MENU are automatically set when you run AUTO SETUP (see page 34). Use
SOUND MENU and BEAM MENU to make additional adjustments.
• BEAM MENU allows you to make settings for the surround sound effects normally available in the speaker settings menu.
• Make settings for the parameters in BEAM MENU first before making settings for the parameters in SOUND MENU, INPUT MENU,
and DISPLAY MENU.
SOUND MENU
Use to manually adjust the various parameters related to the sound output.
Item
Features
Page
TONE CONTROL
Adjusts the output level of high-frequency or low-frequency sound.
86
SUBWOOFER SET
Adjusts the various subwoofer settings.
86
MUTE LEVEL
Adjusts the muting level.
87
AUDIO DELAY
Adjusts the audio delay.
87
ROOM EQ
Adjusts the tonal quality of the listening room.
87
DD/DTS Dynamic Range
Adjusts the dynamic range of Dolby Digital or DTS signals.
88
TruBass
Selects the bass sound enhancer.
88
BEAM MENU
Use to manually adjust the various parameters related to the sound beam output.
Item
Features
Page
SETTING PARAMETERS
Adjusts the listening room and listening position settings.
82
BEAM ADJUSTMENT
Adjusts the various sound beam settings.
83
IMAGE LOCATION
Adjusts the sound position of the front left and right channels.
86
INPUT MENU
Use to manually adjust the various parameters related to the audio and video input.
Item
Features
Page
INPUT ASSIGNMENT
Assigns jacks according to the component to be used.
88
INPUT MODE
Selects the initial input of the source.
89
INPUT TRIM
Adjusts the input level of the source.
89
INPUT RENAME
Renames the displayed input source.
90
HDMI SET
Adjusts the various HDMI settings.
90
DISPLAY MENU
Use to manually adjust the various parameters related to the display.
Item
Features
Page
F.DISPLAY SET
Adjusts the front panel display settings.
92
OSD SET
Adjusts the OSD settings.
93
UNIT SET
Changes the display unit of measurement.
93
80 En
MANUAL SETUP
Using MANUAL SETUP
3
Use the remote control to access and adjust each
parameter.
MUSIC
MOVIE
7
8
ENHANCER
SPORTS
9
OFF
0
Press
/
to select MANUAL SETUP and
press ENTER.
The following screen appears on your TV.
SUR. DECODE
ENTER
+10
ENTER
MENU
ENTRY
TV/AV
ENTER
YSP
DISPLAY
VOLUME
RETURN
CH
;MANUAL SETUP
TV VOL
. 1)SOUND MENU
2)BEAM MENU
3)INPUT MENU
4)DISPLAY MENU
y
1
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
You can adjust the SET MENU parameters while the unit is
reproducing sound.
Set the operation mode selector to YSP.
4
TV/AV
Press
/
ENTER.
to select a sub menu and press
YSP
2
Press MENU.
The SET MENU screen appears on your TV.
ENTER
ENTER
SET MENU
MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
5
Press
/
/ /
each parameter.
and ENTER to configure
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
ADVANCED
OPERATION
ENTER
y
• The control buttons used for SET MENU are displayed at
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN.
• To exit from the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
6
Press MENU to exit.
The OSD disappears from your TV screen.
MENU
English
81 En
MANUAL SETUP
BEAM MENU
ANGLE TO WALL
OR CORNER
FLAT TO WALL
Use to manually adjust the various parameters related to
the sound beam output.
SET MENU → MANUAL SETUP → BEAM MENU
2)BEAM MENU
. A)SETTING PARAMETERS
B)BEAM ADJUSTMENT
C)IMAGE LOCATION
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
You can adjust the sound beam output level of each channel in
“Adjusting the audio balance” (see page 94).
• Select FLAT TO WALL if this unit is installed in
parallel with the wall in your listening room. Adjust the
width and length of your listening room as well as the
distance of the listening position from this unit and the
distance of the center of this unit from the left wall.
Listening position
from the left wall
■ SETTING PARAMETERS
(Setting parameters)
Use to set the position of this unit in your listening room
and the distance of this unit from the listening position.
When you make settings for each parameter, other related
parameters are automatically adjusted to best match your
listening environment.
Listening position
from the unit
Room length
Room width
Note
Choices for the room width and length:
2.0 m to 12.0 m (6.5 ft to 40.0 ft)
Choices for the listening position from this unit:
1.8 m to 9.0 m (6.0 ft to 30.0 ft)
Choices for the listening position from the left wall:
0.6 m to 11.4 m (2.0 ft to 38.0 ft)
A)SETTING PARAMETERS 1/3
p
p
p
. INSTALLED POSITION
;;;;;;;FLAT TO WALL
INSTALLED HEIGHT
;;;;;;;1.0m
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
A)SETTING PARAMETERS 2/3
|
-------[ 5.4m ]|
4.9m
|
Room width and
length
p
p
If you make adjustments in SETTING PARAMETERS, the beam
optimization settings made in the AUTO SETUP procedure will
be lost. If you want to keep the beam optimization settings made
in the AUTO SETUP and make further adjustments, adjust
settings in BEAM ADJUSTMENT first (see page 83).
A)SETTING PARAMETERS 3/3
Listening position
from the unit and
the left wall
--------|
2.7m [ 2.5m ]
|
p
p
INSTALLED POSITION
(Installed position of this unit)
Use to adjust the installed position of this unit.
Choices: FLAT TO WALL (Parallel to wall installation),
ANGLE TO WALL OR CORNER
(Corner installation)
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
82 En
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
MANUAL SETUP
• Select ANGLE TO WALL OR CORNER if this unit is
installed in the corner of your listening room. Adjust
the width and length of your listening room as well as
the distance of the listening position from this unit.
Listening position
from the unit
INSTALLED HEIGHT
(Installed height of this unit)
Use to adjust the installed height of this unit.
Choices: 0.0 m to 3.0 m
Initial setting: 1.0 m
Room width
Room length
Choices for the room width and length:
2.0 m to 12.0 m (6.5 ft to 40.0 ft)
Choices for the listening position from this unit:
1.8 m to 9.0 m (6.0 ft to 30.0 ft)
Floor
0.0 m to 3.0 m
■ BEAM ADJUSTMENT (Beam adjustment)
A)SETTING PARAMETERS 2/3
----- 5.4m ---
p
Notes
p
|
[ 5.4m ]
|
|
Room width and
length
Use to manually adjust the various sound beam settings.
We recommend that you select 5 Beam as the beam mode
before adjusting these parameters (see page 60).
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
A)SETTING PARAMETERS 3/3
• When INSTALLED POSITION is adjusted in MANUAL
SETUP (see page 82), the factory default value is automatically
set for this parameter except Center in FOCAL LENGTH (see
page 85).
• Depending on the beam mode settings (see pages 60 and 66),
some channel positions may not be available for selection. In
this case, “– –” is displayed. When using Stereo plus 3 Beam as
the beam mode, set the surround left and right signals to be
output from the front left and right channels.
B)BEAM ADJUSTMENT
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
p
ADVANCED
OPERATION
\
[ 2.5m ]
\
Listening
position from the
unit
p
p
. a)HORIZONTAL ANGLE
b)VERTICAL ANGLE
c)BEAM TRAVEL LENGTH
d)FOCAL LENGTH
e)TREBLE GAIN
[ ]/[ ]:Up/Down
[ENTER]:Enter
Note
When you set the INSTALLED POSITION parameter in
MANUAL SETUP (see page 82), the parameters newly set for
the width and length of your listening room are automatically set
as the factory default value.
English
83 En
MANUAL SETUP
HORIZONTAL ANGLE (Horizontal angle)
Use to adjust the horizontal angle of sound beams for each
channel. By adjusting the horizontal angle of the sound
beams, you can optimize the sound beam paths. A test
tone is automatically output.
( )
(+)
(+)
( )
BEAM TRAVEL LENGTH (Beam travel length)
A certain amount of delay must be applied to the sound
from each channel so that all sounds can arrive at the
listening position at the same time. This menu sets the
distance that sound beams travel after being output and
reflected off the wall until they arrive at the listening
position and adjusts the delay applied to the respective
channel.
The lines in the illustration below indicate the distance.
Choices: L90° to R90°
Adjust toward L (left) to move the direction of the output
to the left and adjust toward R (right) to move it to the
right.
Front L
L65deg
L90
R90
*
0(deg)
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
VERTICAL ANGLE (Vertical angle)
Use to adjust the vertical angle of sound beams for each
speaker. By altering the beam path, you can optimize
sound beam angles.
c)BEAM TRAVEL LENGTH
5 beam
. Front L;;;;;;;6.0m
Front R;;;;;;;6.0m
Center;;;;;;;;2.5m
Surround L;;;;9.1m
Surround R;;;;9.1m
p
p
a)HORIZONTAL ANGLE5 beam
1/5
Choices: 0.3 m to 24.0 m (1.0 ft to 80.0 ft)
• Front L adjusts the distance the front left channel
sound beams travel.
• Front R adjusts the distance the front right channel
sound beams travel.
• Center adjusts the distance the center channel sound
beams travel.
• Surround L adjusts the distance the surround left
channel sound beams travel.
• Surround R adjusts the distance the surround right
channel sound beams travel.
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
y
Choices: –45° to +45°
Initial setting: 0°
• Adjust toward – (minus) to move the angle downward.
• Adjust toward + (plus) to move the angle upward.
b)VERTICAL ANGLE 1/5
5 beam
(+)
------0deg.
(-)
p
p
Front L
0deg.
84 En
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
We recommend that you use the setting optimized by AUTO
SETUP (see page 34). Adjust this parameter only when you
changed HORIZONTAL ANGLE (see page 84).
MANUAL SETUP
FOCAL LENGTH (Focal length)
Use to set the distance from the front of this unit to the
focal point of output for each channel to achieve an
expansive feeling for each channel.
The focal points except for the center channel should be
set near the reflection points on the walls. The shorter the
distance, the larger the expansion.
TREBLE GAIN (Treble gain)
Use to adjust the high-frequency output level of each
channel.
y
If the reflection points of the front left and right or surround left
and right sound beams are on curtain or other acoustically
absorbent surfaces, you can achieve more effective surround
sound by increasing the treble level for those sound beams.
focal length
focal point
sweet spot
Center channel
( )
(+)
e)TREBLE GAIN-
. Front L;;;;;;;;0dB
Front R;;;;;;;;0dB
Center;;;;;;;;;0dB
Surround L;;;;;0dB
Surround R;;;;;0dB
p
+
--------------------------
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
p
ADVANCED
OPERATION
Choices: –1.0 m to +13.0 m (–3.5 ft to +43.5 ft)
Adjust toward – (minus) to move the focus outward and
adjust toward + (plus) to move the focus toward the
normal position.
• Front L adjusts the focal length for the front left sound
beams.
• Front R adjusts the focal length for the front right
sound beams.
• Center adjusts the focal length for the center sound
beams. Initial setting: –0.5 m (–1.5 ft)
• Surround L adjusts the focal length for the surround
left sound beams.
• Surround R adjusts the focal length for the surround
right sound beams.
p
Front left channel
Choices: –12.0 dB to +12.0 dB
Initial setting: 0 dB
• Front L adjusts the high-frequency output level of the
front left channel.
• Front R adjusts the high-frequency output level of the
front right channel.
• Center adjusts the high-frequency output level of the
center channel.
• Surround L adjusts the high-frequency output level
of the surround left channel.
• Surround R adjusts the high-frequency output level
of the surround right channel.
y
We recommend that you use the initial setting (–0.5 m (or 1.5 ft))
for the center channel.
d)FOCAL LENGTH
5 beam
. Front L;;;;;;+1.5m
Front R;;;;;;+1.5m
Center;;;;;;;-0.5m
Surround L;;;+2.3m
Surround R;;;+2.3m
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
English
85 En
MANUAL SETUP
■ IMAGE LOCATION (Image location)
OFF
L
C
)ON
R
Use to manually adjust the various parameters related to
the sound output.
SET MENU → MANUAL SETUP → SOUND MENU
1)SOUND MENU
. A)TONE CONTROL
B)SUBWOOFER SET
C)MUTE LEVEL
D)AUDIO DELAY
E)ROOM EQ
F)DD/DTS Dynamic Range
G)TruBass
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
C)IMAGE LOCATION
.
SOUND MENU
p
Use to adjust the direction from which the front left and
right channel sound is heard so that each sound can be
heard closer to the center channel.
Use this feature to redirect audio signals if the sound
coming from the front left and right channels seems
unnatural, such as when your listening position is not the
center of your listening room.
You can only adjust this parameter when 3 Beam or 5
Beam is selected as the beam mode (see page 60).
Choices: ON, OFF
Setting range: 0% to 95%
Initial setting: 0%
■ TONE CONTROL (Tone control)
p
You can adjust the tonal quality of sound beams.
LEFT;;;;;;;;;;;0%
RIGHT;;;;;;;;;;0%
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
.
A)TONE CONTROLTREBLE;;;;;0dB
BASS;;;;;;;0dB
p
With the front left
channel adjusted
p
Without adjustment
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
p
LEFT (Left)
Adjusts audio signals toward the left.
The higher the percentage, the louder the output from the
center.
+
-----+
------
TREBLE (Treble)
Use to adjust the high-frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
BASS (Bass)
Use to adjust the low-frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
Without adjustment
With the front right
channel adjusted
■ SUBWOOFER SET (Subwoofer settings)
Use to manually adjust the various subwoofer
settings.
B)SUBWOOFER SET
. BASS OUT;;;;;FRONT
CROSS OVER;;;100Hz
LFE LEVEL;;;;;;0dB
DISTANCE;;;;;;3.0m
p
p
RIGHT (Right)
Adjusts audio signals toward the right.
The higher the percentage, the louder the output from the
center.
86 En
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
MANUAL SETUP
■ MUTE LEVEL (Muting level)
C)MUTE LEVEL
pMUTE
■ ROOM EQ (Room equalizer)
Use to change the tonal qualities of your listening room
when the unit is mounted on the wall.
Choices: MOUNTING (Mount type),
REFLECTING (Reflectivity type)
E)ROOM EQ
. MOUNTING;;;;;SHELF
REFLECTING;;;NORMAL
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
MOUNTING (Mounting type)
Use to enhance medium to low range sounds.
Choices: WALL (Wall mount), SHELF (Shelf mount)
• Select WALL if this unit is mounted on the wall in your
listening room.
• Select SHELF if this unit is mounted on the shelf in
your listening room.
REFLECTING (Reflectivity type)
Use to select the reflectivity of your listening room.
Choices: NORMAL (Normal), HI ECHO (High echo)
• Select NORMAL if your listening room has a normal
reflectivity.
• Select HI ECHO if your listening room has highly
reflective surfaces such as concrete walls.
p
p
-20dB
p
[ ]/[ ]:Select
[ENTER]:Return
ADVANCED
OPERATION
Use to adjust how much the mute function reduces the
volume level.
Choices: MUTE, –20 dB
• Select MUTE to completely halt all sound output.
• Select –20 dB to reduce the current volume level by
20 dB.
AUDIO DELAY;;;;;0msec
p
DISTANCE (Distance)
Select to adjust the distance of the subwoofer from the
listening position.
Choices: 0.3 to 15.0 m (1.0 ft to 50.0 ft)
Initial setting: 3.0 m (10.0 ft)
D)AUDIO DELAY
p
LFE LEVEL (Low-frequency effect level)
Select to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer. The LFE channel carries low-frequency
special effects which are only added to certain scenes.
This setting is effective only when this unit decodes Dolby
Digital or DTS signals.
Choices: –20 to 0 dB
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 160 msec
p
CROSS OVER (Crossover)
When BASS OUT is set to SWFR, you can use this
feature to select a crossover (cutoff) frequency for all lowfrequency signals. All frequencies below the selected
frequency will be sent to the subwoofer position.
Choices: 80Hz, 100Hz, 120Hz
■ AUDIO DELAY (Audio delay)
p
BASS OUT (Bass out)
Low-frequency (bass) signals can be directed to the
subwoofer and/or the front left and right channels. This
setting also determines the routing of LFE (low-frequency
effect) signals found in Dolby Digital or DTS sources.
Choices: SWFR (Subwoofer), FRONT
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer.
• Select FRONT if you do not use a subwoofer. LFE and
low-frequency signals from other channels are directed
to the front left and right channels.
[ ]/[ ]:Select
[ENTER]:Return
English
87 En
MANUAL SETUP
■ DD/DTS Dynamic Range
(Dynamic range of Dolby Digital and
DTS signals)
Use to select the amount of dynamic range compression.
This setting is effective only when the unit is decoding
Dolby Digital and DTS signals. Dynamic range is the
difference between the smallest sound that can be heard
above the noise of the equipment and the biggest sound
that can be heard without distortion.
Choices: MIN (minimum), STD (standard),
MAX (maximum)
STD
[ ]/[ ]:Select
[ENTER]:Return
Select to adjust the dynamic range compression.
• Select MIN for listening to sources at low volume
levels.
• Select STD for general use.
• Select MAX for feature films.
■ TruBass
Use to turn on or off the bass sound enhancer. The SRS
TruBass technology improves bass even without a
subwoofer and provides deeper, richer bass in the presence
of a subwoofer.
Choices: OFF, MID, DEEP
G)TruBass
p
pMID
DEEP
p
OFF
[ ]/[ ]:Select
[ENTER]:Return
Note
TruBass is not available when My Beam (see page 67) or My
Surround (see page 61) is selected as the beam mode.
88 En
[ ]/[ ]:Up/Down
[ENTER]:Enter
pMAX
p
p
3)INPUT MENU
. A)INPUT ASSIGNMENT
B)INPUT MODE
C)INPUT TRIM
D)INPUT RENAME
E)HDMI SET
p
MIN
Use to manually adjust the various parameters related to
the audio and video input.
SET MENU → MANUAL SETUP → INPUT MENU
p
F)DD/DTS Dynamic Range
INPUT MENU
■ INPUT ASSIGNMENT (Input assignment)
Use to assign the HDMI IN jacks of this unit to other
components if the initial settings of this unit do not
correspond to your needs. By assigning other components
to the HDMI IN jacks of this unit, you can display the
names of the connected components in the front panel
display and OSD and operate the components with the
input selector buttons of the same name. If you connect a
component to one of the HDMI IN jacks of this unit and
do not assign a name to it, the default component name for
HDMI IN jack is displayed in the front panel and OSD
when selected.
• Select HDMI1 to assign a component to the HDMI
AUX 1 IN jack of this unit.
Choices: TV/STB, AUX1
• Select HDMI2 to assign a component to the HDMI
DVD IN jack of this unit.
Choices: DVD, AUX2
• Select Line1 to assign a component to the STB
COMPONENT VIDEO IN jacks of this unit.
Choices: TV/STB, AUX1
• Select Line2 to assign a component to the DVD/AUX 2
COMPONENT VIDEO IN jacks of this unit.
Choices: DVD, AUX2
• Select Line3 to assign a component to the AUX 1
VIDEO IN jack of this unit.
Choices: DVD, AUX2
MANUAL SETUP
■ INPUT TRIM (Input trim)
AUX1
AUX1
DVD
DVD
p
)
C)INPUT TRIM 1/2
)
p
. HDMI1;;;;
(
HDMI2;;;;
(
Use to adjust the input level of the input source.
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
. TV/STB
DVD
ANALOG;;;-3.0dB
DIGITAL;;-3.0dB
DIGITAL;;-3.0dB
p
p
A)INPUTHDMI
ASSIGNMENT 1/3
A)INPUTCOMPONENT
ASSIGNMENT 2/3
. Line1;;;;TV/STB
( TV/STB
Line2;;;; DVD
( DVD
)
p
p
)
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
A)INPUT ASSIGNMENT 3/3
COMPOSITE
. Line3;;;; AUX2
( AUX2
p
p
)
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
■ INPUT MODE (Input mode)
B)INPUT MODE
pAUTO
p
p
LAST
[ ]/[ ]:Select
[ENTER]:Return
English
• Select AUTO to set this unit to automatically detect the
type of input signals and select the appropriate input
mode.
• Select LAST to set this unit to automatically select the
last input mode used for that input source. If the type of
input signals is different from the setting, no sounds
will be produced.
• Select TV/STB ANALOG to adjust the level of audio
and video signals input at the TV/STB AUDIO IN
jacks of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select TV/STB DIGITAL to adjust the level of audio
and video signals input at the TV/STB OPTICAL
DIGITAL IN jack of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select DVD DIGITAL to adjust the level of audio and
video signals input at the DVD COAXIAL DIGITAL
IN jack of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select AUX1 ANALOG to adjust the level of audio and
video signals input at the AUX 1 AUDIO IN jacks of
this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select AUX1 DIGITAL to adjust the level of audio and
video signals input at the AUX 1 OPTICAL DIGITAL
IN jack of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select AUX2 DIGITAL to adjust the level of audio and
video signals input at the AUX 2 COAXIAL DIGITAL
IN jack of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select AUX3 ANALOG to adjust the level of audio
signals input at the AUX 3 input jack on the front
panel.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select DOCK ANALOG to adjust the level of audio
signals input at the DOCK terminal of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
ADVANCED
OPERATION
Use to designate the input mode for the input sources
connected to the DIGITAL IN jacks when you turn on the
power of this unit. For information on the types of audio
signals that can be output by this unit, see “Selecting the
input mode” on page 97.
Choices: AUTO, LAST
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
89 En
MANUAL SETUP
■ INPUT RENAME (Input rename)
■ HDMI SET (HDMI settings)
Use to change the name of the input source in the OSD
and the front panel display. Press an input selector button
(e.g., DVD) to select the component you want to change
the name for and perform the following procedure.
Use to change the HDMI audio/video output/input to
match the connected component.
Choices: SUPPORT AUDIO (Support audio),
VIDEO INFO (Video information),
UP-SCALING (HDMI up-scaling),
ASPECT RATIO (HDMI aspect ratio),
HDMI CONTROL (HDMI control)
D)INPUT RENAME
DVD ->
E)HDMI SET
p
p
DVD
p
p
[ ]/[ ]:Position
[ ]/[ ]:Character
[ENTER]:Return
Press / to place the _ (underscore) under
the space or the character you want to edit.
The _ (underscore) flashes.
ENTER
2
SUPPORT AUDIO (Support audio)
Use to select whether to play back HDMI audio signals on
this unit or on another HDMI component connected to the
HDMI OUT jack of this unit.
Choices: YSP-40D, OTHER
a)SUPPORT AUDIO
Press
/
to select the desired character.
• You can use up to 8 characters for each input.
• Press
to change the character in the following
order or press
to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, #, *,
+, etc.
pYSP-40D
p
OTHER
p
1
p
p
. a)SUPPORT AUDIO
b)VIDEO INFO
c)UP-SCALING
d)ASPECT RATIO
e)HDMI CONTROL
[ ]/[ ]:Up/Down
[ENTER]:Enter
[ ]/[ ]:Select
[ENTER]:Return
Notes
ENTER
3
Repeat steps 1 to 2 to rename each input.
4
Press ENTER to exit.
The new names are registered, and the display returns
to the previous screen.
ENTER
90 En
• This setting is effective when HDMI CONTROL is set to OFF
(see page 91).
• The HDMI video signals input at one of the HDMI IN jacks of
this unit are always output at the HDMI OUT jack of this unit.
• When HDMI CONTROL is set to ON, this setting is ineffective.
This unit follows the setting of the HDMI control-compatible
TV.
MANUAL SETUP
VIDEO INFO (Video information)
Use to display the video information of the current input
signal.
Choices: HDMI SIGNAL, HDMI RES., HDMI ERROR
b)VIDEO INFO
. HDMI SIGNAL;;;HDMI -> HDMI
HDMI RES.;;;;1080P -> 1080P
HDMI ERROR;;;----
p
p
[ ]/[ ]:Up/Down
[ENTER]:Return
Notes
• When “MONITOR CHECK” is set to “YES”, this unit receives
the information of the available video signal resolutions from
the video monitor connected via HDMI and you can only select
the resolutions supported by the video monitor in “UPSCALING” (see page 101).
• When “MONITOR CHECK” is set to “SKIP”, an asterisk (*)
appears on the left of the unavailable video signal resolution(s)
(see page 101).
ASPECT RATIO (HDMI aspect ratio)
Use this feature to select the adjustment of aspect ratio for
analog video signals output at the HDMI OUT jack.
Choices: THROUGH, 16:9 Normal, Smart Zoom
• Select HDMI SIGNAL to display the type of the
HDMI input/output signals.
• Select HDMI RES. to display the resolution of the
HDMI input/output signals.
• Select HDMI ERROR to display the error message for
HDMI sources or devices connected
(see page 115 for details).
c)UP-SCALING
p
• Select OFF to deactivate the HDMI up-conversion
feature
• Select THROUGH not to up-scale any analog video
signals.
• Select 480p (or 576p), 1080i, or 720p to up-scale
analog video signals to 480p (or 576p), 1080i, or 720p
of resolution.
• Select THROUGH if you do not make any adjustments
to the aspect ratio for HDMI video signal sources.
• Select 16:9 Normal to display video images with 4:3 of
aspect ratio on your video monitor with 16:9 of aspect
ratio. Black stripes appear on the right and left sides as
a result.
• Select Smart Zoom to fit video images with 4:3 of
aspect ratio to your video monitor with 16:9 of aspect
ratio.
Notes
• When “UP-SCALING” is set to “THROUGH”, you cannot
make any adjustments to “ASPECT RATIO”.
• When “ASPECT RATIO” is set to “Smart Zoom”, the video
images of the edge of the video monitor are rather stretched.
• When the video signals are input at the HDMI IN jacks or the
signals are input with 720p or 1080i of resolution, the
“ASPECT RATIO” setting does not affect the video signals
output at the HDMI OUT jack.
ADVANCED
OPERATION
HDMI UP-SCALING;;;*720p
XXX(480pXX1080iXXX*720p)XX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
p
[ ]/[ ]:Select
[ENTER]:Return
HDMI ASPECT RATIO;;;THROUGH
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
p
[ ]/[ ]:Select
[ENTER]:Return
p
UP-SCALING (HDMI up-scaling)
Use this feature to activate or deactivate the HDMI upconversion of the analog video signals input at the
composite video and component video jacks so that the
up-scaled analog video signals are output at the HDMI
OUT jack. This unit up-scales the analog video signals as
follows:
• 480i (NTSC)/576i (PAL) → 480p (NTSC)/576p (PAL),
1080i or 720p
• 480p (NTSC)/576p (PAL) → 1080i or 720p
Choices: OFF, THROUGH, 480p (or 576p), 1080i, 720p
d)ASPECT RATIO
HDMI CONTROL (HDMI control)
Use this function to link this unit and an HDMI controlcompatible TV via HDMI. You can turn on or off the
power, select the input mode, and adjust the volume level
of this unit using the remote control supplied with your
HDMI control-compatible TV. For details, see “Using the
HDMI control feature” on page 79.
Choices: OFF, ON
English
91 En
MANUAL SETUP
e)HDMI CONTROL
OFF
p ON XXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
p
[ ]/[ ]:Select
[ENTER]:Return
DISPLAY MENU
Use to manually adjust the various parameters related to
the display.
SET MENU → MANUAL SETUP → DISPLAY MENU
p
4)DISPLAY MENU
. A)F.DISPLAY SET
B)OSD SET
C)UNIT SET
• Select ON to enable the HDMI control. The signals
input at the HDMI IN jacks are output at the HDMI
OUT jack when this unit is in the standby mode.
• Select OFF to disable the HDMI control. The signals
input at the HDMI IN jacks are not output at the HDMI
OUT jack when this unit is in the standby mode.
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ F.DISPLAY SET
(Front panel display settings)
Use to adjust the brightness and display settings of the
front panel display.
A)F.DISPLAY SET
. STANDARD DIMMER;;;;;OFF
AUTO DIMMER
;;;;;;;;;;;;;OFF
SCROLL;;;;;;;;;;;;CONT.
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
STANDARD DIMMER (Standard dimmer)
Use to adjust the brightness of the front panel display
when you operate this unit by using the control buttons on
the front panel or on the remote control.
Choices: –2, –1, OFF
AUTO DIMMER (Auto dimmer)
If no operation is performed for a specified period of time,
the front panel display dims. Use to adjust the brightness
of the front panel display in this case.
Choices: OFF (the same brightness as the STANDARD
DIMMER setting), –1 to –3 (based on the
STANDARD DIMMER setting), DISPLAY OFF
SCROLL (Front panel display scroll)
Use to select the mode to display information in the front
panel display when operating your iPod.
Choices: CONT., ONCE
• Select CONT. to continue to scroll the display.
• Select ONCE to scroll the display to the end once, after
which the first 15 characters appear and stay.
92 En
MANUAL SETUP
■ OSD SET (OSD settings)
Use to adjust the display position and to set the display
time of the OSD.
B)OSD SET
. OSD SHIFT;;;;;;;;;;0
OSD DISPLAY TIME;;;ON
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
OSD SHIFT (OSD shift)
Use to adjust the vertical position of the OSD. Adjust
toward the – (minus) direction to raise the position of the
OSD, and adjust toward the + (plus) direction to lower it.
Choices: –5 to +5
Initial setting: 0
OSD DISPLAY TIME (OSD display time)
Use to set the interval for which the OSD screen is
displayed after an operation.
Choices: ON, 10s, 30s
• Select ON to show the OSD screen constantly.
• Select 10s to turn off the OSD screen 10 seconds after
an operation.
• Select 30s to turn off the OSD screen 30 seconds after
an operation.
y
The OSD display time setting is available for your iPod (see
page 58).
■ UNIT SET (Unit settings)
Use this to change the display unit of measurement.
Choices: METERS, FEET
FEET
p
p
ADVANCED
OPERATION
C)UNIT SET
p METERS
[ ]/[ ]:Select
[ENTER]:Return
• Select METERS to enter distances in meters.
• Select FEET to enter distances in feet.
Note
If you change this setting, the adjusted sound beam settings may
change.
English
93 En
Adjusting the audio balance
Adjusting the audio balance
You can adjust the sound beam output level of each channel by using the test tone or the audio output being played back
in each beam mode to achieve a more true-to-life surround sound experience.
Using the test tone
3
You can use the test tone feature to output a test tone from
each channel to manually balance the channel levels.
Use this to set the channel levels so that the volume level
of each channel is identical when heard from your
listening position.
Press
/
to select the channel you want
to adjust.
The front panel display changes as follows:
TEST FRONT L
ENTER
ENHANCER
ENTRY
TEST CENTER
MENU
TEST FRONT R
TV/AV
ENTER
YSP
DISPLAY
RETURN
TEST SUR.R
VOLUME
CH
TV VOL
TEST SUR.L
MUTE
TV INPUT
CH LEVEL
TEST
TEST SWFR
TV MUTE
CODE SET
Note
1
Set the operation mode selector to YSP.
TV/AV
YSP
2
“TEST SWFR” is only available when a subwoofer is
connected to this unit and SWFR is selected for BASS OUT
in SOUND MENU (see page 87).
Press TEST.
“TEST FRONT L” appears in the front panel display
and a test tone is output from the front left channel.
TEST
TEST FRONT L
94 En
4
Press
/
to adjust the channel volume.
ENTER
Control range: –10.0 dB to +10.0 dB
Adjusting the audio balance
5
Press TEST when you have completed all
your adjustments.
1
Set the operation mode selector to YSP.
TV/AV
TEST
YSP
2
Notes
• All channel levels cannot be adjusted when the 2-channel or
5-channel stereo playback (see page 63), My Beam
(see page 61), or My Surround (see page 61) is selected as the
beam mode.
• “FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is
selected as the beam mode (see page 61).
• “FRONT L/R” are automatically adjusted depending on the
settings of the other channels when Stereo plus 3 Beam or
stereo playback is selected as the beam mode (see pages 61 and
66).
Press CH LEVEL repeatedly (or press
CH LEVEL and
/
) to select the channel
you want to adjust.
The front panel display changes as follows.
CH LEVEL
or
CH LEVEL
ENTER
y
If the level of a particular channel cannot be adjusted, “– –dB”
appears in the front panel display.
Using the audio output being
played back
You can also manually adjust the channel levels while
playing back an input source such as a DVD.
ENHANCER
ENTRY
FRONT L
+1.0dB
CENTER
-2.5dB
FRONT R
+1.0dB
SUR.R
+2.0dB
SUR.L
+2.0dB
MENU
TV/AV
ENTER
YSP
DISPLAY
CH
TV VOL
SWFR
MUTE
CH LEVEL
TV INPUT
TEST
TV MUTE
CODE SET
--dB
Note
ADVANCED
OPERATION
VOLUME
RETURN
“SWFR” is available only when a subwoofer is connected to
this unit and SWFR is selected for BASS OUT in SOUND
MENU (see page 86).
English
95 En
Adjusting the audio balance
3
Press
/
to adjust the channel volume.
ENTER
Control range: –10.0 dB to +10.0 dB
4
Wait for a few seconds without operating this
unit when you have completed your
adjustment.
Notes
• All channel levels cannot be adjusted when the 2-channel or
5-channel stereo playback (see page 66), or My Surround (see
page 61) is selected as the beam mode.
• “FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is
selected as the beam mode (see page 41).
• Only CENTER can be adjusted when My Beam is selected as
the beam mode (see page 67).
• “FRONT L/R” are automatically adjusted depending on the
settings of the other channels when Stereo plus 3 Beam or
stereo playback is selected as the beam mode (see pages 61 and
66).
y
If the level of a particular channel cannot be adjusted, “– –dB”
appears in the front panel display.
96 En
Selecting the input mode
Selecting the input mode
You can select the type of audio input signals of the selected input source according to your preference or the conditions
of the input source. This function is available for TV/STB, DVD, AUX1, and AUX2.
y
We recommend setting the input mode to AUTO in most cases.
AV
3
TV
DOCK
DVD
AUX1
STB
TV
AUX2
Press INPUTMODE repeatedly to toggle
between input modes.
AUX3
TV
INPUT1 MACRO
SEARCH
INPUTMODE
MEMORY
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
3BEAM
9
DVD
AUTO
TV/STB
AUTO
DVD
DTS
TV/STB
DTS
TV/STB
ANALOG
SUR. DECODE
+10
0
ENHANCER
ENTRY
MENU
When DVD is selected
as the input source
TV/AV
AUX1
AUTO
AUX1
DTS
AUX1
ANALOG
When TV or STB is selected
as the input source
ENTER
YSP
DISPLAY
1
RETURN
Set the operation mode selector to YSP.
When AUX1 is selected
as the input source
AUX2
AUTO
AUX2
DTS
When AUX2 is selected
as the input source
TV/AV
Note
YSP
2
Press one of the input selector buttons to
select the desired input source.
AUX1
STB
TV
AUX2
• AUTO
Automatically selects audio input signals in the following
priority order:
1) HDMI
2) Digital
3) Analog
ADVANCED
OPERATION
DVD
ANALOG is not available as the input mode of DVD and
AUX2.
y
Use this input mode in most cases.
• DTS
Selects only digital signals encoded in DTS.
Compared to AUTO, this input mode provides greater
stability while playing back CDs or LDs encoded in DTS.
• ANALOG
Selects only analog signals.
Even when both digital and analog signals are input
simultaneously, only analog signals are selected.
You can adjust the default input mode to be selected when the
power of this unit is turned on by adjusting INPUT MODE in
INPUT MENU (see page 89).
97 En
English
y
Adjusting the system parameters
Adjusting the system parameters
This unit has additional menus that are displayed in the front panel display. These menus offer additional operations to
adjust and customize the way this unit operates.
Note
When “F.PANEL KEY” is set to “F.PANEL: OFF” (see page 104), STANDBY/ON on the front panel is ineffective. Use STANDBY/ON
on the remote control instead to adjust the system parameters.
Using the system parameters
2
Follow the procedure below to enter the system
parameters.
Press and hold INPUT on the front panel and
press STANDBY/ON on the remote control to
turn on the power of this unit.
“MEMORY PROTECT” is displayed in the front
panel display.
STANDBY/ON
INPUT
MEMORY PROTECT
INPUT
VOLUME
+
STANDBY/ON
3
STANDBY/ON
POWER POWER
AV
ENHANCER
ENTRY
AUX1
AUX2
TV/AV
AUX3
ENTER
YSP
TV
INPUT1 MACRO
STB
DISPLAY
TV
SEARCH
MENU
TV
DOCK
DVD
RETURN
MEMORY
DAB
(U.S.A. and Canada models)
1
Press STANDBY/ON on the remote control to
turn off the power of this unit.
STANDBY/ON
98 En
Release INPUT on the front panel.
INPUT
Adjusting the system parameters
Setting the MEMORY PROTECT
4
You can protect the settings you saved in the system
memory of this unit from being accidentally erased or
unwantedly changed.
Press / to switch between “PROTECT:
ON” and “PROTECT: OFF”.
ENTER
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
TV/AV
PROTECT: ON
YSP
3
Confirm that “MEMORY PROTECT” is
displayed in the front panel display and
press ENTER.
PROTECT: OFF
• Select PROTECT: ON to activate the protection
feature.
• Select PROTECT: OFF to deactivate the protection
feature.
MEMORY PROTECT
5
ENTER
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
STANDBY/ON
The new setting will be activated when you turn on
the power of this unit next time.
ADVANCED
OPERATION
English
99 En
Adjusting the system parameters
Setting the MAX VOLUME
5
You can set the maximum volume level so that this unit
will not output sound beyond the limited volume level.
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
Press
level.
/
to adjust the maximum volume
ENTER
Control range: MAX, 99 to 01, MIN
Control step: 1
“
TV/AV
YSP
3
6
Press
/
so that “MAX VOLUME SET” is
displayed in the front panel display.
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
STANDBY/ON
The new setting for the maximum volume level will
be activated when you turn on the power of this unit
next time.
ENTER
Setting the TURN ON VOLUME
You can set the initial volume level when the power of this
unit is turned on.
MAX VOLUME SET
4
Press ENTER.
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
TV/AV
ENTER
100 En
YSP
Adjusting the system parameters
3
Press
/
so that “TURN ON VOLUME” is
displayed in the front panel display.
ENTER
Setting the MONITOR CHECK
Use this feature to activate or deactivate the monitor check
function of this unit. When this parameter is set to “YES”,
this unit receives the information on the available video
signal resolutions from the video monitor connected via
HDMI (see page 19). If your TV monitor is not
compatible with 1080i and/or 720p of resolutions, you
cannot select “1080i” and/or “720p” in “UP-SCALING”
(see page 91).
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
TURN ON VOLUME
4
Press ENTER.
TV/AV
YSP
ENTER
5
Press
/
3
Press
/
so that “MONITOR CHECK” is
displayed in the front panel display.
to adjust the initial volume level.
ENTER
ENTER
Control range: MAX, 99 to 01, OFF
Control step: 1
MONITOR CHECK
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
ADVANCED
OPERATION
6
STANDBY/ON
The new setting for the maximum volume level will
be activated when you turn on the power of this unit
next time.
English
101 En
Adjusting the system parameters
4
Press / to switch between “MON CHK:
YES” and “MON CHK: SKIP”.
ENTER
Setting the DEMO MODE
You can test the sound beam output from this unit to
experience the sound beam.
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
TV/AV
MON CHK:
YSP
YES
3
MON CHK:
Press
/
so that “DEMO MODE” is
displayed in the front panel display.
SKIP
ENTER
• Select MON CHK: YES to activate the monitor
check function.
• Select MON CHK: SKIP to deactivate the monitor
check function.
5
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
STANDBY/ON
The new setting will be activated when you turn on
the power of this unit next time.
Note
If you change the setting of “MONITOR CHECK”, “UPSCALING” is automatically set to “OFF” (see page 91).
102 En
DEMO MODE
Adjusting the system parameters
4
Press / to switch between “DEMO: ON”
and “DEMO: OFF”.
ENTER
Setting the PANEL INPUT KEY
You can disable the INPUT on the front panel when you
adjust the system parameters.
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
TV/AV
DEMO:
YSP
ON
3
DEMO:
Press
/
so that “PANEL INPUT KEY” is
displayed in the front panel display.
OFF
ENTER
• Select DEMO: ON to activate the demo mode.
• Select DEMO: OFF to deactivate the demo mode.
5
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
STANDBY/ON
PANEL INPUT KEY
ADVANCED
OPERATION
The new setting will be activated when you turn on
the power of this unit next time.
Press ENTER while playing back sources to test the
sound beam.
The sound beam being output shuttles between left
and right. Press ENTER again to stop shuttling.
English
103 En
Adjusting the system parameters
4
Press / to switch between “P.INPUT: ON”
and “P.INPUT: OFF”.
ENTER
Disabling the front panel keys
You can disable the front panel keys except when you
adjust the system parameters.
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
TV/AV
P.INPUT:
YSP
ON
3
P.INPUT:
OFF
Press
/
so that “F.PANEL KEY” is
displayed in the front panel display.
ENTER
• Select P.INPUT: ON to enable the INPUT key on
the front panel.
• Select P.INPUT: OFF to disable the INPUT key on
the front panel. “F.PANEL KEY” is automatically
set to “ON”.
5
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
STANDBY/ON
The new setting will be activated when you turn on
the power of this unit next time.
104 En
F.PANEL KEY
Adjusting the system parameters
4
Press / to switch between “F.PANEL:
ON” and “F.PANEL: OFF”.
ENTER
Setting the FACTORY PRESET
You can reset all of the parameters of this unit to the
factory presets. This procedure completely resets ALL the
parameters in SET MENU.
Note
After performing the following procedure you must run AUTO
SETUP again to match your surround sound environment.
F.PANEL: ON
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 98.
2
Set the operation mode selector to YSP.
TV/AV
YSP
F.PANEL: OFF
3
Press
/
so that “FACTORY PRESET” is
displayed in the front panel display.
• Select F.PANEL: ON to enable the front panel
keys.
• Select F.PANEL: OFF to disable the front panel
keys. “P.INPUT” is automatically set to “ON”.
5
ENTER
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
STANDBY/ON
FACTORY PRESET
4
Press ENTER.
ADVANCED
OPERATION
The new setting will be activated when you turn on
the power of this unit next time.
ENTER
English
105 En
Adjusting the system parameters
5
Press / to switch between “PRESET:
RESET” and “PRESET: CANCEL”.
ENTER
PRESET: RESET
PRESET:CANCEL
• Select PRESET: RESET to reset all of the current
settings.
• Select PRESET: CANCEL to cancel the resetting
procedure.
6
Press STANDBY/ON on the remote control to
set this unit to the standby mode.
STANDBY/ON
The new setting will be activated when you turn on
the power of this unit next time.
106 En
Remote control features
Remote control features
In addition to controlling this unit, the remote control can also operate other AV components made by Yamaha and other
manufacturers. To control other components, you must set up the remote control with the appropriate remote control
codes and set the operation mode selector to TV/AV to change the control area.
Note
Depending on the external AV component you are using, you may not be able to operate the component with the remote control, even if
a remote control code is set. In this case, operate the component using the supplied remote control.
Setting remote control codes
2
You can control other components by setting the
appropriate remote control codes. Codes can be set up for
each input area (DVD, AUX1, AUX2, STB, and TV).
For a complete list of available remote control codes, refer
to “List of remote control codes” at the end of this manual.
Press the numeric buttons to enter the
remote control code while holding down
CODE SET.
Setting example: Yamaha DVD input area
MY SUR.
6
TV MUTE
Transmission indicator
AV
While holding
down, press
SPORTS
9
CODE SET
TV
SPORTS
DOCK
AUX1
DVD
AUX2
9
AUX3
TV
INPUT1 MACRO
TV
STB
SEARCH
MEMORY
STB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
3
9
SUR. DECODE
+10
ENHANCER
MUTE
CH LEVEL
TEST
TV MUTE
CODE SET
Note
Press and hold CODE SET and press one of
the input selector buttons to select the input
source you want to set a remote control code
for.
The transmission indicator flashes twice and remains
lit.
Proceed to step 2 while holding down CODE SET.
TV MUTE
CODE SET
While holding
down, press
DVD
AUX1
STB
TV
AUX2
If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
ADVANCED
OPERATION
1
TV INPUT
Refer to “Controlling other components” on
page 108 to operate the external component
using the remote control.
If the external component functions correctly the
remote control code setup is successful.
If the external component does not function correctly,
the remote control code may be incorrect. Confirm
that the remote control code is correct. See “List of
remote control codes” at the end of this manual and
start over from step 1.
If the remote control is without batteries for more than
two minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries and reset the remote control codes.
When changing the batteries, be careful not to press
any of the buttons on the remote control. Doing so will
clear the contents of the memory.
English
107 En
Remote control features
Controlling other components
■ Operating your TV
Set the operation mode selector to TV/AV, and
press TV to select TV as the input source.
The control area of the remote control changes to the TV
operation mode.
TV/AV
TV
YSP
STANDBY/ON
4
TV
DOCK
DVD
AUX1
AUX2
AUX3
TV
INPUT1 MACRO
TV
STB
SEARCH
MEMORY
5
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
1
5BEAM
ST+3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
3BEAM
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
9
SUR. DECODE
+10
ENTRY
MENU
TV/AV
ENTER
YSP
DISPLAY
VOLUME
RETURN
CH
TV VOL
2
3
108 En
6
MUTE
TV INPUT
CH LEVEL
TEST
TV MUTE
CODE SET
2 CH +/–
Switches between the available TV channels.
3 TV INPUT
Switches the input source for your TV.
4 TV POWER
Turns on or off the power of your TV.
POWER POWER
AV
1 Numeric buttons
Selects a TV channel for playback.
7
5 TV INPUT1
Selects the input source of your TV.
6 TV VOL +/–
Adjusts the audio output level of your TV.
7 TV MUTE
Temporarily mutes audio output from your TV.
Remote control features
■ Operating your DVD player/recorder
Set the operation mode selector to TV/AV and
press DVD to select DVD as the input source.
The control area of the remote control changes to the DVD
operation mode.
TV/AV
■ Operating your STB
(CATV/Satellite tuner)
Set the operation mode selector to TV/AV and
press STB to select STB as the input source.
The control area of the remote control changes to the STB
operation mode.
DVD
YSP
TV/AV
STB
YSP
STANDBY/ON
POWER POWER
AV
TV
DOCK
AUX1
DVD
AUX2
4
STANDBY/ON
POWER POWER
AV
AUX3
TV
INPUT1 MACRO
TV
STB
DVD
SEARCH
TV
DOCK
AUX1
AUX2
3
AUX3
TV
INPUT1 MACRO
MEMORY
DAB
TV
STB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
SEARCH
MEMORY
DAB
5BEAM
1
ST+3BEAM
3BEAM
AUTO
VOL MODE SETUP INPUTMODE SLEEP
1
2
3
STEREO
MY BEAM
MY SUR.
5BEAM
ST+3BEAM
4
5
6
1
2
3
MUSIC
MOVIE
SPORTS
STEREO
MY BEAM
MY SUR.
7
0
ENHANCER
9
8
OFF
1
SUR. DECODE
+10
ENTRY
MENU
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
5
3BEAM
0
ENHANCER
9
SUR. DECODE
+10
ENTRY
MENU
TV/AV
2
ENTER
YSP
DISPLAY
VOLUME
RETURN
CH
MUTE
TV INPUT
CH LEVEL
TEST
TV/AV
6
ENTER
YSP
TV VOL
DISPLAY
RETURN
VOLUME
CH
MUTE
TV INPUT
TV VOL
2
TV MUTE
CODE SET
TV MUTE
CODE SET
3
1 Numeric buttons
Enter numeric digits.
2 Cursor buttons
/
/
Use to select DVD menu items.
ADVANCED
OPERATION
1 Numeric buttons
Enter numeric digits.
2 CH +/–
Switches between the available STB channels.
/
, ENTER
3 AV POWER
Turns on or off the power of your STB.
3 Operation buttons for DVD players
Operate your DVD player/recorder, such as play and stop.
4 AV POWER
Turns on or off the power of your DVD player/recorder.
5 MENU
Displays the DVD menu.
English
6 RETURN
Use to return to the previous DVD menu screen or exit
from the DVD menu.
109 En
Remote control features
■ Operating your VCR
Set the operation mode selector to TV/AV and
press AUX1 to select VCR as the input source.
The control area of the remote control changes to the
AUX1 operation mode.
y
This operation is available when your VCR is connected to the
AUX 1 AUDIO IN jacks on this unit.
TV/AV
AUX1
YSP
STANDBY/ON
POWER POWER
AV
TV
DOCK
DVD
AUX1
AUX2
4
AUX3
TV
INPUT1 MACRO
TV
STB
SEARCH
MEMORY
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
1
5BEAM
ST+3BEAM
1
2
3BEAM
3
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
OFF
0
ENHANCER
9
SUR. DECODE
+10
ENTRY
MENU
TV/AV
ENTER
YSP
DISPLAY
RETURN
VOLUME
CH
MUTE
TV INPUT
TV VOL
2
CH LEVEL
TEST
TV MUTE
CODE SET
3
1 Numeric buttons
Enter numeric digits.
2 CH +/–
Switches between the available VCR channels.
3 Operation buttons for VCR
Operate your VCR, such as play and stop.
4 AV POWER
Turns on or off the power of your VCR.
110 En
Remote control features
■ Setting macros for the TV with the
tuning capability
Using the TV macro
The TV macro feature makes it possible to perform a
series of operations with the press of a single button. For
example, when you want to play a DVD, you would
normally turn on the component, select DVD as the input
source, and press the play button to start playback. The TV
macro feature lets you perform all of these operations
simply by pressing the DVD macro button.
1
Press and hold CODE SET and press one of
the input selector buttons to select the input
source you want to set macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
While holding
down, press
Notes
• Be sure to set up a remote control code for your TV before
setting macros.
• The ways to set macros differ if your TV does not have the
tuning capability.
• If you press any control buttons on the remote control other than
the ones used to set macros while setting macros, the setting
procedure is automatically canceled.
• If it takes more than 10 seconds in steps 2 and 3, the setting
procedure is automatically canceled. In this case, repeat from
step 1.
CODE SET
2
DVD
AUX1
AUX2
STB
Press MACRO while holding down CODE
SET.
TV MUTE
MACRO
While holding
down, press
CODE SET
STANDBY/ON
POWER POWER
AV
TV
DOCK
AUX1
DVD
AUX2
AUX3
3
TV
INPUT1 MACRO
TV
STB
SEARCH
MEMORY
Press CH +/– or the numeric buttons to select
the TV channel.
Check that the TV screen changes to the tuner screen.
DAB
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
5BEAM
ST+3BEAM
3BEAM
1
2
3
1
2
3
STEREO
MY BEAM
MY SUR.
STEREO
MY BEAM
MY SUR.
4
5
6
MUSIC
MOVIE
SPORTS
7
8
CH
OFF
0
ENHANCER
or
9
7
8
9
+10
4
YSP
RETURN
Press TV INPUT repeatedly until the screen
changes to the display of the input source
selected in step 1.
TV VOL
TV INPUT
MUTE
TV INPUT
CH LEVEL
TEST
ADVANCED
OPERATION
TV/AV
CH
6
SPORTS
MENU
ENTER
VOLUME
5
MOVIE
0
+10
DISPLAY
4
MUSIC
OFF
SUR. DECODE
ENTRY
3BEAM
TV MUTE
CODE SET
5
Press ENTER to confirm the macro setting.
ENTER
English
111 En
Remote control features
■ Setting macros for the TV without the
tuning capability
1
Press and hold CODE SET and press one of
the input selector buttons to select the input
source you want to set macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
DVD
Press and hold one of the input selector buttons
for approximately two seconds to select the input
source you want to operate macros for.
The TV input changes at the same time the input mode
changes.
DVD
AUX2
While holding
down, press
While holding
down, press
1
MACRO
CODE SET
Press and hold CODE SET and press one of
the input selector buttons to select the input
source you want to cancel the macros for.
Proceed to step 2 while holding down CODE SET.
DVD
TV MUTE
Press INPUT1.
Check that the TV screen changes to the input 1
screen.
INPUT1
Press TV INPUT repeatedly until the screen
changes to the display of the input source
selected in step 1.
TV INPUT
Press MACRO while holding down CODE
SET.
While holding
down, press
Press ENTER to cancel the macros.
ENTER
5
Press ENTER to confirm the setting.
ENTER
112 En
MACRO
CODE SET
3
AUX2
STB
CODE SET
2
AUX1
While holding
down, press
TV MUTE
4
AUX2
■ Canceling the macros
Press MACRO while holding down CODE
SET.
TV MUTE
3
AUX1
STB
STB
CODE SET
2
AUX1
■ Operating macros
Troubleshooting
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the AC power supply cable, and
contact the nearest authorized Yamaha dealer or service center.
■ General
Problem
Cause
Remedy
See
page
The AC power supply cable is not firmly
connected to the AC wall outlet.
Connect the AC power supply cable firmly
to the AC wall outlet.
28
This unit has been exposed to a strong
external electric shock (such as lightning
and strong static electricity).
Set this unit to the standby mode, disconnect
the AC power supply cable, plug it back in
after 30 seconds, and use it normally.
—
This unit suddenly enters the
standby mode.
The internal temperature becomes too high
and the overheat protection circuitry has
been activated.
Wait for about one hour for this unit to cool
down and turn it back on.
—
The sleep timer has turned the unit off.
Turn on the power and play back the source
again.
—
Incorrect input or output cable connections.
Connect the cables properly. If the problem
persists, the cables may be defective.
17
No appropriate input source has been
selected.
Select an appropriate input source with
INPUT or the input selector buttons.
44
The volume is turned down.
Turn up the volume.
46
The sound is muted.
Press MUTE or VOLUME +/– to resume
audio output and adjust the volume level.
46
The signals this unit cannot reproduce (such
as PCM signals with more than 96 kHz of
sampling frequency) are being received
from the source component.
Play a source whose signals can be
reproduced by this unit.
—
Change the system settings of the source
component.
—
The HDMI components connected to this
unit do not support the HDCP copy
protection standards.
Connect the HDMI components that support
the HDCP copy protection standards.
18
SUPPORT AUDIO is set to OTHER and
HDMI audio signals are not being played
back on this unit.
Set SUPPORT AUDIO to YSP-40D in
MANUAL SETUP
90
The sleep timer has turned this unit off.
Turn on the power and play back the source
again.
—
The sound is muted.
Press MUTE or VOLUME +/– to resume
audio output and adjust the volume level.
46
No sound from the effect
channels.
You are playing back the source or program
in the 2-channel stereo playback or My
Beam mode.
Press one of the beam mode buttons on the
remote control to select a multi-channel
playback mode and play back the source or
program once more.
60
No sound from the center
channel.
The output level of the center channel is set
to minimum.
Raise the level of the center channel.
94
No sound from the surround
channels.
The output level of the surround channels is
set to minimum.
Raise the output level of the surround
channels.
94
No sound.
The sound suddenly goes
off.
ADDITIONAL
INFORMATION
This unit fails to turn on
when STANDBY/ON is
pressed, or enters the
standby mode soon after the
power has been turned on.
English
113 En
Troubleshooting
Problem
No sound from the
subwoofer.
Cause
BASS OUT in SUBWOOFER SET is set to
FRONT.
Remedy
Select SWFR.
See
page
87
The source does not contain low bass signals.
Distorted or too little bass
sound.
CROSS OVER in SUBWOOFER SET is set
incorrectly.
Set CROSS OVER correctly.
One of the night listening enhancers is
currently selected.
Turn off the night listening enhancers.
TruBass is currently turned on.
Turn off TruBass.
88
The volume level of the subwoofer is too high.
Turn down the volume level of the subwoofer.
—
The listening room is not a regular shape.
Install this unit in a square or rectangular
shaped room.
—
There is no wall in the path of the sound
beam.
Try placing a flat object, such as a board, in
the path of the sound beam.
—
Dolby Digital or DTS sources
cannot be played back.
(Dolby Digital or DTS
indicator does not light up in
the front panel display.)
The connected component is not set to
output Dolby Digital or DTS digital signals.
Make an appropriate setting following the
operating instructions for your component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO.
97
There is noise interference
when a subwoofer is not
connected to this unit.
The protection circuitry was in operation
because a source with strong bass elements
was played back.
Turn down the volume level.
46
Select SWFR for BASS OUT.
87
Connect a subwoofer and adjust settings for
SUBWOOFER SET.
86
Too much bass sound.
Surround sound effects are
insubstantial.
86
75
Low-frequency sounds are
distorted.
CROSS OVER in SUBWOOFER SET is set
incorrectly.
Set CROSS OVER correctly.
87
On-screen display does not
appear.
The OSD video pin cable is not connected
properly.
Connect the cable properly.
20
This unit does not operate
properly.
The internal microcomputer has been frozen
by an external electric shock (such as
lightning or excessive static electricity) or
by a power supply with low voltage.
Disconnect the AC power supply cable from
the outlet and plug it in again after about 30
seconds.
—
No sound is heard from the
TV connected via HDMI.
The TV does not accept the multi-channel
audio signals.
Convert the multi-channel audio signals to
the 2-channel audio signals at the source
component such as a DVD player.
—
“SUPPORT AUDIO” is set to “YSP-40D”.
Set “SUPPORT AUDIO” to “OTHER”.
90
There is noise interference
from digital or highfrequency equipment.
This unit is too close to the digital or highfrequency equipment.
Move this unit farther away from such
equipment.
—
This unit does not output
effect sounds properly.
The original source includes surround effects.
Disable the surround effect settings of this unit.
—
My Beam auto-adjust
function does not work.
The listening room is too noisy.
Keep the listening room as quiet as possible.
—
Try manual-adjust function.
68
The sound reflectivity of the listening room
is too much.
Set REFLECTING to HI ECHO.
87
The remote control may be operated outside
of the remote control operation range.
The remote control functions within a
maximum range of 6 m (20 ft) and no more
than 45 degrees off-axis from the front
panel.
29
The function does not work properly
because of the condition of the connected
components.
Select My Beam and then try again.
67
114 En
Troubleshooting
■ Remote control
Problem
The remote control does not
work and/or function
properly.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control functions within a
maximum range of 6 m (20 ft) and no more
than 45 degrees off-axis from the front
panel.
29
Direct sunlight or lighting (from an inverter
type of fluorescent lamp, etc.) is striking the
remote control sensor of this unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
29
The external component you want to operate
is not selected as the input source.
Press INPUT on the front panel or the input
selector buttons on the remote control to
select the external component you want to
operate.
44
The remote control code was not correctly
set.
Set the remote control code correctly or try
another code for the same manufacturer
using the “List of remote control codes” at
the end of this manual.
107
Even if the remote control code is correctly
set, there are some models that do not
respond to the remote control.
Use the remote control supplied with the
external component.
—
The cursor buttons do not
work during SET MENU
operation.
The operation mode selector was
unwantedly set to TV/AV.
Set the operation mode selector to YSP.
—
Cannot use the My Beam
auto-adjust function.
Wrong distance or angle.
The remote control functions within a
maximum range of 6 m (20 ft) and no more
than 45 degrees off-axis from the front
panel.
29
Cannot operate external
components with the remote
control of this unit.
■ HDMI
Error message
Cause
Remedy
See
page
Device Error
The number of the connected HDMI
components exceeds the limit.
Reduce the number of the connected HDMI
components.
—
HDCP Error
HDCP authentication failed.
Check that the connected HDMI
components support the HDCP copy
protection standards.
—
Out of Resolution
The resolution of the HDMI output signals
exceeds the limit allowed by your TV.
Adjust UP-SCALING.
91
ADDITIONAL
INFORMATION
English
115 En
Troubleshooting
■ DAB
Problem
Cause
Cannot tune into any DAB
services.
The INIT SCAN operation
was not successful, and “Not
Available” appears in the
front panel display.
Remedy
See
page
INIT SCAN has not been performed yet, or
the DAB registry list needs to be updated.
Perform INIT SCAN
53
There may be no DAB coverage in your
area.
Check with your dealer or visit WorldDAB
online at “http://www.worlddab.org” for a
listing of the DAB coverage in your area.
—
The DAB signals are weak.
Use a commercially available high-quality
outdoor DAB antenna.
—
The DAB antenna may not be connected.
Make sure that the DAB antenna is firmly
connected.
27
The DAB signals are weak.
Use a commercially available high-quality
outdoor DAB antenna.
—
The position of the indoor DAB antenna
and/or this unit is not optimal for DAB
reception.
Use TUNE AID to locate the best location
of the indoor DAB antenna and this unit for
optimal DAB reception.
54
The DAB signals are weak.
Use a commercially available high-quality
outdoor DAB antenna.
—
The indoor DAB antenna needs to be
repositioned.
Readjust the position of the indoor DAB
antenna.
27
The DAB signals are weak.
Use a commercially available high-quality
outdoor DAB antenna.
—
The DAB service may be temporarily out of
service or is not provided by the DAB
broadcasting company.
Contact the DAB broadcasting company.
—
There is no DAB service in your area.
The DAB service reception is
weak.
There is noise interference
(e.g. hiss or crackle)
The DAB service information
does not appear or is
inaccurate.
■ iPod
Note
In case of a transmission error with no status message appearing in the front panel display and in the OSD, check the connection
between your iPod and this unit.
Status message
Loading...
Cause
Remedy
See
page
This unit is in the middle of recognizing
the connection with your iPod.
This unit is in the middle of acquiring the
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Turn off this unit and reconnect the Yamaha iPod
universal dock to the DOCK terminal of this unit.
57
Try resetting your iPod.
—
Only iPod (Click and Wheel), iPod nano, and iPod
mini are supported.
—
Unknown iPod
Your iPod is not supported by this unit.
iPod connected
The connection between your iPod and
this unit is completed.
Disconnected
Your iPod is removed from the Yamaha
iPod universal dock.
Set your iPod back in the Yamaha iPod universal
dock.
57
Unable to play
This unit cannot play back the files stored
on your iPod.
Check the playability of the files stored on your iPod.
—
Store other playable music files on your iPod.
—
116 En
Glossary
Glossary
■ Dolby Digital
■ DTS Digital Surround
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (left, center, and right) and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low-frequency effect), the system has
a total of 5.1-channels (LFE is counted as 0.1-channel).
By using 2-channel stereo for the surround channels, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with excitement and realism
previously unheard of.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. DTS, Inc. has developed a
home theater system so that you can enjoy the depth of
sound and natural spatial representation of DTS digital
surround in your home. This system produces practically
distortion-free 6-channel sound (technically, left, right,
and center channels, 2 surround channels, plus an LFE
0.1-channel as a subwoofer, for a total of 5.1 channels).
The unit incorporates a DTS-ES decoder that enables 6.1channel reproduction by adding the surround back channel
to existing 5.1-channel format.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround software.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels (instead of
only 1 surround channel for conventional Pro Logic
technology). Music and Game modes are also available for
2-channel sources in addition to the Movie mode.
■ Dolby Surround
Neo:6 decodes the conventional 2-channel sources for 6channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
modes are available: Music mode for playing music
sources and Cinema mode for movies.
■ EUPHONY
Euphony is a revolutionary sound field reproduction
system implemented with state-of-the-art sound
technologies developed under the basic concept of
enjoying beautiful sound. It can reproduce surround sound
optimized without depending on the number of input
channels, the number of speakers (two or more speakers)
or the speaker’s dimensions. In addition, it features steady
center localization. It also can reproduce the surround
sound for the headphones with natural sound and “out-ofhead” localization so that the listener feels an expanded
sound and will not tire, even when listening to music or a
movie for long time.
■ HDMI
117 En
English
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital audio/video
interface. Providing an interface between any source (such
as a set-top box or AV receiver) and an audio/video
monitor (such as a digital television), HDMI supports
standard, enhanced, or high-definition video as well as
multi-channel digital audio using a single cable. HDMI
transmits all ATSC HDTV standards and supports 8channel digital audio, with bandwidth to spare to
accommodate future enhancements and requirements.
When used in combination with HDCP (High-bandwidth
Digital Content Protection), HDMI provides a secure
audio/video interface that meets the security requirements
of content providers and system operators. For further
information on HDMI, visit the HDMI website at
“http://www.hdmi.org/”.
ADDITIONAL
INFORMATION
Dolby Surround uses a 4-channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
■ DTS Neo:6
Glossary
■ LFE 0.1-channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low-frequency range compared to the full-range
reproduction by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded, and transmitted
without using any compression. This is used as a method
of recording CDs and DVD audio. The PCM system uses
a technique for sampling the size of the analog signal per
very small unit of time. Standing for pulse code
modulation, the analog signal is encoded as pulses and
then modulated for recording.
■ SRS TruBass
SRS TruBass is a psychoacoustic bass enhancement
technology developed by SRS Labs, Inc. for speakers and
headphone systems that delivers bass up to an octave
below the physical capabilities of the speaker’s driver.
SRS TruBass technology takes advantage of a
spontaneous tendency of the human ears to infer lowrange audio data when presented with higher-frequency
harmonic signals. As a result, our ears can hear the
original low-range sound that the speaker system is
incapable of producing.
118 En
DAB frequency table
DAB frequency table
Band III
Frequency
Channel label
218.640 MHz
11B
220.352 MHz
11C
222.064 MHz
11D
223.936 MHz
12A
225.648 MHz
12B
227.360 MHz
12C
229.072 MHz
12D
ADDITIONAL
INFORMATION
English
119 En
Index
Index
■ Numerics
■ M
3 Beam............................................................................ 61
5 Beam............................................................................ 60
MANUAL SETUP.......................................................... 80
MEMORY....................................................................... 41
Movie program ............................................................... 72
Music program................................................................ 71
My Beam ........................................................................ 67
■ A
AC power supply cable................................................... 28
Audio pin cable............................................................... 18
AUTO SETUP (IntelliBeam) ......................................... 34
■ B
Battery ............................................................................ 29
BEAM MENU................................................................ 82
Beam mode......................................................... 60, 66, 67
■ C
■ N
Night listening enhancer ................................................. 75
■ O
On-screen display (OSD)................................................ 31
Optical cable ................................................................... 18
OSD video pin cable ....................................................... 18
Cable clamp .................................................................... 18
Cardboard microphone stand.......................................... 36
CINEMA DSP ................................................................ 71
■ P
■ D
■ R
DAB................................................................................ 47
DEMO MODE.............................................................. 102
Demonstration DVD......................................................... 6
Digital audio pin cable.................................................... 18
DISPLAY MENU........................................................... 92
Dolby Digital .................................................................. 62
Dolby Pro Logic ............................................................. 62
Dolby Pro Logic II.......................................................... 62
DTS ................................................................................ 62
DTS Neo: 6..................................................................... 62
Dynamic range................................................................ 88
Rear panel ......................................................................... 9
Remote control................................................................ 11
Remote control code ..................................................... 107
Remote control sensor .................................................... 29
■ E
EUPHONY ................................................................... 117
■ F
FACTORY PRESET..................................................... 105
Fastener........................................................................... 16
Front panel........................................................................ 7
Front panel display ........................................................... 8
■ H
HDMI ............................................................................. 18
HDMI cable .................................................................... 18
■ I
IntelliBeam ..................................................................... 34
IntelliBeam microphone ................................................. 35
■ L
LFE 0.1-channel ........................................................... 118
120 En
PCM .............................................................................. 118
Power .............................................................................. 30
■ S
SET MENU .................................................................... 31
Sleep timer ...................................................................... 76
Sound field program ....................................................... 69
Stereo plus 3 Beam ......................................................... 61
Surround mode................................................................ 62
Surround sound ............................................................... 60
SOUND MENU.............................................................. 86
Sports program................................................................ 72
Stereo sound.................................................................... 66
System parameter............................................................ 98
■ T
Test tone.......................................................................... 94
TruBass ........................................................................... 88
TV macro ...................................................................... 111
TV volume equal mode................................................... 75
■ V
Volume ............................................................................ 46
Volume mode .................................................................. 75
Specifications
Specifications
AMP SECTION
• Maximum Output Power (JEITA)
................................................. 2 W (1 kHz, 10% THD, 4 Ω) × 40
20 W (100 Hz, 10% THD, 4 Ω) × 2
SPEAKER SECTION
DAB SECTION
• Tuning Range
...............................................................................218 to 230 MHz
• Sensitivity
.......................................................................................... –99 dBm
• Signal to Noise Ratio ...............................................................97 dB
• Driver
Small dia. speakers
...................... 4 cm (1-9/16 in) cone magnetic shielding type × 40
Woofers
...................... 11 cm (4-5/16 in) cone magnetic shielding type × 2
• Total Harmonic Distortion ....................................................0.005%
• Frequency response ................................................. 55 Hz to 20 kHz
(-10 dB, stereo mode)
GENERAL
CONNECTIONS
• Input Jacks
TV/STB, AUX 1 AUDIO IN (1 V, 32 kΩ) .......... 2 pairs (Analog)
TV/STB, AUX 1 OPTICAL DIGITAL IN ....... 2 (Optical digital)
DVD, AUX 2 COAXIAL DIGITAL IN ........... 2 (Coaxial digital)
STB, DVD/AUX 2, AUX 1 VIDEO IN ...................3 (Composite)
STB, DVD/AUX 2 COMPONENT VIDEO IN .... 2 (Component)
AUX 1, DVD HDMI IN ...............................................................2
AUX 3 ...........................................................................................1
• Stereo Separation (1 kHz) ........................................................95 dB
• Frequency Response (20 Hz to 20 kHz) ............................. ± 0.5 dB
• Power Supply ........................................... AC 220–240 V, 50/60 Hz
• Power Consumption ................................................................. 55 W
• Standby Power Consumption ...................................... 0.5 W or less
• Dimensions (W x H x D) .............................. 1030 x 198 x 144 mm
(40-17/32 x 7-21/32 x 5-22/32 in)
• Weight ........................................................... 15.5 kg (34 lbs 10 oz)
*
Specifications are subject to change without notice.
• Output Jacks
SUBWOOFER (1.5 V, less than 120 Hz) ............... 1 (Subwoofer)
VIDEO OUT (1 Vp-p, 75 Ω) ...................................1 (Composite)
COMPONENT VIDEO OUT
(Y: 1 Vp-p, 75 Ω PB/PR: 0.5 Vp-p, 75 Ω) ........... 1 (Component)
HDMI OUT ..................................................................................1
• System Connector Jack
INTELLIBEAM MIC .................................. 1 (Microphone input)
RS-232C ...........................................................1 (System control)
IR IN .................................................................1 (System control)
HDMI interface of this unit is based on the following standard:
• HDCP (High-bandwidth Digital Content Protection System)
licensed by Digital Content Protection, LLC.
ADDITIONAL
INFORMATION
English
121 En
Specifications
Limited Guarantee for European Economic Area (EEA) and Switzerland
Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from
whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our
website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).
The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha
undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge
for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been
discontinued or is considered uneconomic to repair.
Conditions
1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a
statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the
product may be returned at the customer’s expense.
2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.
3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.
4. The following are excluded from this guarantee:
a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.
b. Damage resulting from:
(1) Repairs performed by the customer himself or by an unauthorised third party.
(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to
ensure the product is adequately packaged when returning the product for repair.
(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper
use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in
the country where it is used.
(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.
(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.
(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety
standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.
(7) Non AV (Audio Visual) related products.
(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or
http://www.yamaha-uk.com/ for U.K. resident.)
5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.
6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the
product.
7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.
8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising
from their sales/purchase contract.
122 En
List of remote control codes
TV
ADMIRAL
292, 293, 216
AIWA
294, 276, 283, 284
AKAI
295, 296
ALBA
296
AOC
297
BELL &
HOWELL
292
BESTAR
298
BLAUPUNKT 229, 222
BLUE SKY
298
BRANDT
223
BROC SONIC 297
BUSH
296
BYD:SIGN
201, 202
CLATRONIC 298
CRAIG
224
CROSLEX
225, 298
CURTIS MATHIS
297, 226
DAEWOO
297, 298, 224,
227, 228
DAYTRON
239
DUAL
298
DWIN
293, 281
EMERSON
297, 224, 239, 232
FURGUSON 223, 265, 266
FIRST LINE 298
FISHER
295, 233
FRABA
298
FUJITSU
289
FUNAI
277, 278
GE
293, 297, 234,
235, 236
GOODMANS 296, 298, 223
GRUNDIG
229, 238, 249
HITACHI
297, 239, 242,
243, 285, 206
ICE
296
IRRADIO
296
ITT/NOKIA
244, 245
JC PENNY
293, 297, 234, 237
JVC
296, 246, 247, 286
KENDO
298
KTV
297, 239
LG/GOLDSTAR
297, 298, 239, 237
LOEWE
298, 248, 207
LXI
293, 297, 225,
226, 233, 298
MAGNAVOX 297, 225, 239, 298
MARANTZ
298, 210
MATSUI
295
MEDION
203, 204, 298
MEMOREX
297, 216
MITSUBISHI 299, 297, 259, 287
NAD
226, 255
NEC
297, 252, 282
NOKIA
244, 245
NOKIA OCEANIC
245
NORDMENDE 265, 266
ONWA
296
PANASONIC 234, 235, 236,
253, 288, 211
PHILCO
297, 225, 239, 298
PHILIPS
298, 225, 205
PIONEER
226, 235, 254,
255, 268
PORTLAND 297, 256
PROSCAN
293, 221
PROSCAN
231, 241, 251
PROTON
297, 250, 260, 270
QUASAR
234, 235
RADIO SHACK299, 293, 297
RCA
293, 297, 234,
256, 257, 258, 221
RUNCO
220, 230, 271
SABA
223, 269, 265, 266
SAMPO
281, 297, 280
SAMSUNG
297, 239, 248,
262, 275
SANYO
295, 233, 279,
272, 273, 274, 212
SCHNEIDER 296
SCOTT
297
SHARP
292, 239, 232,
213, 208
SIEMENS
229
SIGNATURE 216
SIGNATURE 292
SONY
263, 214
SYLVANIA
297, 225, 298
SYNPHONIC 217, 218, 219
TELEFUNKUN 269, 264, 265, 266
THOMSON
223, 266
TOSHIBA
292, 226, 267, 215
VIDECH
297, 242
WARDS
297, 239, 232, 216
YAMAHA
299, 292, 242,
285, 287, 253, 206
YAMAJI
298
ZENITH
216, 261, 271
DVD PLAYER
AIWA
648, 649
APEX DIGITAL
652, 653, 654
BYD:SIGN
678, 679
DAEWOO
655
DENON
623, 624, 682
FUNAI
625
HARMAN/KARDON
656, 657
HITACHI
626, 688, 689
JVC
627, 643, 692
KENWOOD
628
KLH
658
LG/GOLDSTAR
645, 663, 664
MARANTZ
699, 659
MITSUBISHI 629
ONKYO
632, 633, 634
PANASONIC 623, 635, 668,
672, 682, 683, 684
PHILIPS
699, 647, 659
PIONEER
636, 637, 638,
673, 674, 675, 685
686, 687
RCA
639
SAMSUNG
642
SHARP
643, 692
SONY
644, 676, 677
SYLVANIA
662
SYMPHONIC 662
THOMSON
646
TOSHIBA
634, 665, 666, 667
YAMAHA
699, 622, 623,
647, 682
ZERITH
663, 664
VCR
ADMIRAL
395
AIWA
396, 397, 398, 329
AKAI
322, 323, 324
AUDIO DYNAMIC
392, 394
BELL & HOWELL
393
BLAUPUNKT 325, 326
BROC SONIC 327
BUSH
322
CANON
325, 328
CGM
396, 332
CITIZEN
396
CRAIG
396, 363
CURTHIS MATHIS
397, 328, 333
DAEWOO
328, 334, 335
DBX
392, 394
DIMENSIA
333
DYNATECH 397
EMERSON
327, 334, 396, 397
FISHER
393, 336
FUNAI
397
GE
328, 333, 387
GO VIDEO
321, 331, 341,
351, 363
GOODMANS 334, 337
GRUNDIG
332, 338
HITACHI
325, 333, 349,
342, 343
INSTANT REPLAY
325, 328
ITT/NOKIA
393
JC PENNY
392, 393, 394,
328, 333, 349,
396, 363
JVC
392, 394, 344,
345, 346, 347
KENDO
396
KENWOOD
392, 394, 396
LG/GOLDSTAR
396, 388
LOEWE
396, 337
LUXOR
395
LXI
393, 396, 397,
336, 349
MAGNAVOX 325, 326, 328
MARANTZ
392, 394
MARTA
396
MATSUI
396
MEMOREX
328, 336, 396, 397
MINOLTA
333, 349
MITSUBISHI 399, 344, 348,
359, 353, 352
MTC
363, 397
MULTITECH 397, 348, 354
NEC
392, 394, 344, 383
NOKIA
393, 395
NOKIA OCEANIC
395
OKANO
323
OLYMPIC
325, 328
ORION
327
PANASONIC 325, 328, 339,
355, 378, 384,
385, 386
PENTAX
333, 349
PHILCO
325, 328, 397
PHILLIPS
325, 326, 328,
337, 356, 357
PHONOLA
337
PILOT
396
PIONEER
325
QUASAR
325, 328
RCA/PROSCAN
325, 326, 328,
333, 335, 349,
358, 363, 397
REALISTIC
393, 397, 328,
336, 359, 362,
396, 363
SAMSUNG
354, 358, 363,
364, 365, 366
SANSUI
394
SANYO
393, 336, 367
SCHNEIDER 337
SCOTT
399, 335, 336,
348, 359, 354,
358, 352
SELECO
322
SHARP
395, 362, 382
SIEMENS
393
SIGNATURE 2000
395, 397
SONY
368, 379, 372,
373, 374, 375
SYLVANIA
397, 325, 326, 328
SYMPHONIC 397
TANDBERG 334
TANDY
397
TASHIRO
396
TATUNG
392, 394
TEAC
392, 394, 397
TECHNICS
325, 328
TEKNIKA
396
TELEFUNKUN
376, 377
THOMAS
397
THORN
393, 396
TOSHIBA
335, 389
TOTEVISION 363, 396
UNITECH
363
UNIVERSUM 396, 327, 376
VIDEOSONIC 363
W.WHOUSE 396
WARDS
395, 396, 336,
362, 397, 363
YAMAHA
399, 392, 393, 394
ZERITH
344, 361, 368,
371, 379, 396, 397
CABLE TV TUNER
ABC
739, 752, 753,
755, 758, 759, 762
GENERAL INSTRUMENT
722, 786, 787, 788
HAMIN
723, 724, 725,
726, 727
HITACHI
722
JEROLD
722, 728, 729,
732, 733, 734,
735, 736, 737
MAGNAVOX 738
MOTOROLA 748, 728
OAK
739, 742, 743
PANASONIC 744, 745, 746,
747, 783, 784
PHILLIPS
763, 764, 765,
766, 767, 768
PIONEER
748, 785, 747
RADIO SHACK749
i
RCA
744, 792, 793
SCIENTIFIC ATLANTA
752, 753, 754, 789
SONY
756, 757
TOCOM
755
UNIVERSAL 769, 772, 773,
774, 775
VIEWSTAR
764, 766, 776,
777, 778, 779, 782
SATELLITE TUNER
ECHOSTAR
822
GE
837, 838, 839
GENERAL INSTRUMENT
823
HITACHI
824
HUGHES
843, 844, 845, 846
JVC
822
MAGNAVOX 825
PANASONIC 826, 829
PHILLIPS
825, 843, 844,
845, 846, 847,
848, 849
PRIMESTAR 827
PROSCAN
837, 838, 839, 842
RADIO SHACK
828
RCA
837, 838, 839, 842
SAMSUNG
852
SKY+
853
SKY HD
853
SONY
832, 835
TOSHIBA
833, 836
UNIDEN
825
ZENITH
834
ii
00cv_YSP-40D_B.fm Page 1 Wednesday, October 17, 2007 8:31 AM
B
YSP-40D
YSP-40D
Digital Sound ProjectorTM
© 2007
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WK94330
Items used for connections and operations
in this guide
s Audio pin cable (x1)
s OSD* video pin cable (x1)
s Optical cable (x1)
s Coaxial cable (x1)
s AC power supply cable (x1)
s IntelliBeam microphone (x1)
s Cardboard microphone stand (x1)
s Demonstration DVD (x1)
*OSD: On-Screen Display
YSP-40D
QUICK REFERENCE GUIDE
This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the
surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner’s Manual.
1
2
Connecting external components to this unit
Connecting external components such as a TV or DVD player to this unit.
Connect your TV or DVD player to this unit using appropriate cables as shown below. After all connections are complete, plug the power supply cable into the AC
wall outlet. For further information on connecting other components, see pages 17 to 28 in the Owner’s Manual.
Connection
example 2
Connection
example 1
This connection example shows a way to connect external components such as a TV or DVD player to
this unit by using the supplied cable. You can enjoy the multi-channel audio from the DVD player and the
analog/digital audio from the TV. Use the video pin cable supplied with your DVD player to make a video
connection between your DVD player and this unit.
Installing this unit
TV
Decide where to install this unit.
Optical
digital
output
Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired
surround sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner.
TV
Analog
audio
output
R
L
Video
input
Coaxial
digital
output
2
Digital satellite tuner/Cable TV tuner/
Digital airwave tuner
DVD player
DVD player
1. Pull out the cap
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
This connection example shows a way to make the most of the capability of this unit. You can
enjoy DVD audio and video with higher quality via the HDMI cable. In case your TV does not have
a built-in digital satellite tuner, cable TV tuner, or digital airwave tuner, connect a digital satellite
tuner, cable TV tuner, or digital airwave tuner via the HDMI cable. For details, see “Connections
using HDMI cables” on page 19 in the Owner’s Manual.
Video
output
2. Check the direction
1
Install this unit in the corner at a 40˚ to 50˚ angle from the
adjacent walls.
Pull out the cap
before
connecting the
optical cable,
and then check
the direction to
insert the
cable.
HDMI
INPUT
HDMI connection
HDMI
OUTPUT
AUX1
Video connection
1
Subwoofer
(Sold separately)
2
(Sold separately)
This connection is not
necessary if your TV has a
built-in digital satellite tuner,
cable TV tuner, or digital
airwave tuner. Use the optical
cable supplied with this unit to
make an audio connection
between your TV and this unit.
For details, see “Connection
example 1”.
DVD
IN
An object, such as furniture
An object, such as furniture
2
1
3
4
OUT
HDMI
Front left channel
40˚ to 50˚
Center channel
Front left channel
Center channel
Front right channel
Front right channel
Surround left channel
Surround left channel
Surround right channel
Surround right channel
* The rear panel illustration
shows jacks and their names to
FM75
UNBAL.
COMPONENT
COMPONENT
ANTENNA
COMPONENT
SUBWOOFER
DVD
help you find them easily.
They are not exactly the same
as the ones on the actual rear
VIDEO OUT
STB
DVD/AUX 2
VIDEO IN
AUX 1
TV/STB AUX 1
AUDIO IN
DOCK
AUX 2
Audio connection
* The rear panel illustration
shows jacks and their names to
COAXIAL
help you find them easily.
OPTICAL
They are not exactly the same
TV/STB
AUX 1
DIGITAL IN
as the ones on the actual rear
panel of this unit.
YSP-40D
panel of this unit.
AL.
ANTENNA
COMPONENT
Do not plug
the power
supply cable
into an AC wall
outlet until all
connections
are complete.
SUBWOOFER
To the AC wall outlet
Install this unit using a rack, etc.
YSP-40D
Depending on your installation environment, connections with external components (see “2 Connecting external components to this unit”) can be done before
installing this unit. We recommend that you temporarily place and arrange all components in order to decide which procedure must come first. In case you
install this unit on top of a rack, etc., use the supplied fasteners to prevent an accidental fall of this unit.
For further information on installation, see page 14 in the Owner’s Manual.
To the AC wall outlet
Connect cables in the following order.
The following is an example of installing this unit in a rack. To prevent this unit or the floor from being scratched, we recommend putting a piece of
cloth on the floor in step 2.
1 Place this unit in front of
2 Place this unit upside
3 Install this unit in the
the rack.
down and connect this unit
to your TV and DVD player.
rack.
DVD/AUX 2
VIDEO IN
Do not plug the power supply
cable into an AC wall outlet
until all connections are
complete.
TV/STB AUX 1
AUDIO IN
Subwoofer
3
Audio connection
5
Supplied
4 Installation is completed.
AUX 1
Connect cables in the following order.
1 Audio pin cable
(Outputs TV analog audio sounds from this unit)
4 Digital audio pin cable
(Outputs DVD digital audio sounds from this unit)
2 OSD video pin cable
(Displays the DVD analog video and the YSP-40D menu
screen on the TV)
5 AC power supply cable
(Connects this unit to the AC wall outlet)
Supplied
3 AC power supply cable
(Connects this unit to the AC wall outlet)
Sold separately
1 HDMI cable
(Displays the DVD digital video and the YSP-40D menu
screen on the TV)
2 HDMI cable
(Inputs DVD digital audio/video signals to this unit)
3 Optical cable
(Outputs TV digital audio sounds from this unit)
y Hint
y Hint
y Hint
• To enjoy better surround effects, place this unit on the upper shelf to keep it away from the floor.
• You can also use the optional metal wall bracket (sold separately) to mount this unit on the wall. For details, refer to the instructions
supplied with the metal wall bracket.
Note
Check whether the digital audio output of your TV and DVD
player is turned on.
If you have connected external components,
follow the steps on the backside to start the Continued
on the back
AUTO SETUP procedure.
Be careful not to leave scratches on this unit or the rack.
Printed in Malaysia
0822_YSP-40D_guide.p65
Note
If you have connected external components,
follow the steps on the backside to start the Continued
on the back
AUTO SETUP procedure.
Check whether the digital audio output of your TV and DVD player is
turned on.
C2007
WK94440 [En]
1
If you connect this unit to an HDMI control-compatible TV (except
some models) via HDMI, you can use the remote control supplied
with your TV to turn on or off the power, select the audio output
component, and adjust the volume level of this unit.
8/22/07, 2:31 PM
All rights reserved.
Continued from the front
3
Carry out the AUTO SETUP (IntelliBeam)
Carry out the AUTO SETUP to adjust the settings that best match your
listening environment.
6 Set the operation mode selector
to YSP.
This unit switches to the YSP operation mode.
ENHANCER
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output
during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
ENTRY
ENTER
1 Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC
jack on the front panel.
DISPLAY
The following screen appears on the TV. Leave the room
within 10 seconds before the AUTO SETUP procedure
starts.
MENU
2
3
4
YSP
ENHANCER
ENTRY
MENU
AUTO SETUP START
RETURN
Will begin in 10sec
YSP
DISPLAY
7 Press and hold AUTO SETUP for
more than 2 seconds.
Please leave the room
TV/AV
ENTER
The menu screen appears on the TV.
If the menu screen does not appear, check the OSD video
pin cable (see the connection example on the front page).
INTELLIBEAM MIC
4
Enjoying surround sound
Enjoy TV or DVD digital audio in surround sound.
For instructions on how to operate or set your TV or DVD player, refer to the owner’s manual supplied with each component.
Enjoying DVDs in surround sound
Enjoying TV in surround sound
TV/AV
You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam
microphone on top of it as shown below.
1
10 Press ENTER to start the AUTO
SETUP procedure, and then
leave the room within 10 seconds.
**-------[RETURN]:Cancel
RETURN
The setup screen automatically changes during the AUTO
SETUP procedure.
When the AUTO SETUP procedure is completed, the
following screen appears on the TV.
1 Select the DVD video input on
your TV.
1 Select the TV channel using the
remote control supplied with
your TV.
2 Set the operation mode selector
to YSP.
2 Set the operation mode selector
to YSP.
SHOW RESULT
This unit switches to the YSP operation mode.
This unit switches to the YSP operation mode.
MEASUREMENT COMPLETE
IntelliBeam microphone (supplied)
SEARCH
MEMORY
DAB
Cardboard microphone stand (supplied)
VOL MODE
AUTO
SETUP INPUTMODE
SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE
AUTO SETUP
PREPARATION & CHECK
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
[ENTER]:Save set-up
[RETURN]:Do not save set-up
IntelliBeam
microphone
Center height of
this unit
Place the IntelliBeam microphone on
the extended center line of this unit
and 1.8 m (6.0 ft) or more away from
it. Also, make sure place the
IntelliBeam microphone within 1 m
(3.3 ft) upper or lower from the center
height of this unit.
Upper bound
position of the
microphone
Within 1 m
(3.3 ft)
Cardboard
microphone stand
More than 1.8 m (6.0 ft)
Within 1 m
(3.3 ft)
Listening
position
Lower bound position
of the microphone
Center line
Cardboard
microphone
stand
8 Check the following points.
About the IntelliBeam microphone
• Is the microphone placed on an imaginary center line drawn
from this unit?
• Is the microphone placed within 1 m (3.3 ft) upper or lower
from the center height of this unit?
• Is the microphone placed more than 1.8 m (6.0 ft) from the
front of this unit?
About the room environment
• Is your listening room kept as quiet as possible?
Subwoofer
VOLUME
STANDBY/ON
POWER
POWER
TV
AV
3
y Hint
• The result may differ depending on the environment.
• If any error occurs, the corresponding error message appears
on the screen. In this case, see “Error messages for AUTO
SETUP” on page 40 in the Owner’s Manual and then follow
the instructions. To start the AUTO SETUP procedure once
again, press RETURN.
9 Prepare to leave the room.
CROSSOVER/
HIGH CUT
If the OSD video pin cable is connected to the video input 1
on the TV as shown in the connection example, switch the
video input to “1”.
AUX1
AUX2
INPUT1
AUX3
TV
MIN
MAX
MIN
ENHANCER
ENTRY
MENU
AUTO SETUP COMPLETE
TV/AV
ENTER
YSP
2
Please remove the MIC from
the YSP and the listening
position.
RETURN
12 Disconnect the IntelliBeam
microphone.
This unit switches to the TV playback mode.
DOCK
DVD
AUX1
AUX2
INPUT1
INPUT1
AUX3
TV
STB
TV
MACRO
TV
MACRO
TV
SEARCH
MEMORY
VOL MODE
AUTO
SETUP INPUTMODE
SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
4 Check the digital signal being output at this unit.
Input channel indicators
The input channel indicators (see page 8 in the Owner’s Manual) are lit in the front panel display, and they switch
according to the channel composition of the corresponding input source. If the sound is output from your TV
speakers, mute the volume on your TV. For details about digital audio input signals, see page 62 in the Owner’s
Manual.
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
5BEAM
ST+3BEAM
1
2
3
STEREO
MY BEAM
MY SUR.
4
5
6
5 Press VOLUME +/- on the remote control to adjust the volume
level of this unit.
The AUTO SETUP has completed. Keep the IntelliBeam
microphone in a safe place.
The settings are automatically saved in the system memory.
6 Press one of the beam mode buttons on the remote control
to select the desired beam mode.
Select one of the six beam modes that best matches the current input source of this unit.
For further information on the beam modes, see page 60 in the Owner’s Manual.
MAX
3BEAM
MACRO
INTELLIBEAM MIC
0822_YSP-40D_guide.p65
This unit switches to the DVD playback mode.
3 Press TV on the remote control
of this unit.
2) Play back the supplied demonstration
DVD on the DVD player.
11 Press ENTER.
DOCK
DVD
RETURN
DAB
y Hint
• When leaving the room, bring this guide with you.
• Wait outside the room during the AUTO SETUP procedure.
• The AUTO SETUP procedure takes about 3 minutes.
• To cancel the AUTO SETUP procedure after it is started,
press RETURN.
5 Select the appropriate video
input on your TV.
1) Press DVD on the remote
control of this unit.
STB
DISPLAY
The power of this unit turns on.
Before operations, insert batteries into the remote control
(see page 29 in the Owner’s Manual).
If necessary, adjust the volume level of this unit.
If you have connected the subwoofer, set the volume and
crossover/high cut frequency. Refer to the note on page
35 in the Owner’s Manual.
YSP
DISPLAY
The following screen appears on the TV for 2 seconds and
then the menu screen disappears from the TV.
IntelliBeam
microphone
4 Turn on the power of your TV.
RETURN
If “ENVIRONMENT CHECK (FAILED) is displayed, see page
39 in the Owner’s Manual and then run the procedure again.
The best setting may not be done if you are in the room.
Prepare to leave the room in 10 seconds after pressing
ENTER in step 10.
3 Press STANDBY/ON on the
remote control.
TV/AV
ENTER
YSP
DISPLAY
2 Set the IntelliBeam microphone at your normal listening position.
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would
be when you are seated.
TV/AV
ENTER
8/22/07, 2:31 PM
To fine-tune the listening environment parameters manually or make advanced settings for speaker positions,
sound beams, etc., see “MANUAL SETUP” on page 80 in the Owner’s Manual.