Bosch 1200 Series IP Installation manual

1200 Series IP Video Storage System
en
Installation Manual
1200 Series IP Video Storage System
Table of Contents | en
3
Table of Contents
1
Safety Instructions
4
1.1
Overview
4
1.2
Warnings and Precautions
4
1.3
Preparing for Setup
4
1.4
Electrical Safety Precautions
4
1.5
General Safety Precautions
5
1.6
System Safety
5
2
System Overview
6
3
System Interface
7
3.1
Control Panel Buttons
7
3.2
Control Panel LEDs
7
4
Installation
9
5
Chassis Setup and Maintenance
10
5.1
Removing the Chassis Cover
10
5.2
Rotating the Hard Drive Cage
11
5.3
Removing and Installing Hard Drives
11
5.4
Installing the I/O Shield and Motherboard
13
5.5
Installing the System Fan
13
5.6
Power Supply
13
A
Appendix
14
A.1
Motherboard layout
14
A.2
Chipset Overview
19
A.3
PC Health Monitoring
19
A.4
Power Configuration Settings
20
A.5
Power Supply
20
A.6
Super I/O
20
A.7
iSCSI Support
21
A.8
Overview of the Nuvoton BMC Controller
21
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
4
en | Safety Instructions
1200 Series IP Video Storage System
1
Safety Instructions
1.1
Overview
This chapter provides a quick setup checklist to get your chassis up and running. Following
the steps in the order given should enable you to have your chassis setup and operational
within a minimal amount of time. This quick setup assumes that you are an experienced
technician, famailiar with common concepts and terminology.
1.2
Warnings and Precautions
You should inspect the box the chassis was shipped in and note if it was damaged in any way.
If the chassis itself shows damage, file a damage claim with carrier who delivered your
system.
Avoid areas where heat, electrical noise and eletromagnetic fields are generated. Position the
chassis near at least one grounded power outlet.
1.3
Preparing for Setup
The 1200 Series chassis contains many features that are unique to the 1200 Series chassis
model. Read this manual in its entirety before beginning the installation procedure.
1.4
Electrical Safety Precautions
Basic electrical safety precautions should be followed to protect yourself from harm and the
1200 Series from damage:
–
Be aware of the locations of the power on/off switch on the chassis as well as the room’s
emergency power-off switch, disconnection switch or electrical outlet. If an electrical
accident occurs, you can then quickly remove power from the system.
–
Do not work alone when working with high voltage components.
–
Power should always be disconnected from the system when removing or installing main
system components, such as the serverboard, memory modules and optical device
drives. When disconnecting the power, you should first power down the system with the
operating system and then unplug the power cords from all the power supply modules in
the system.
–
When working around exposed electrical circuits, another person who is familiar with the
power-off controls should be nearby to switch off the power, if necessary.
–
Use only one hand when working with powered-on electrical equipment. This is to avoid
making a complete circuit, which will cause electrical shock. Use extreme caution when
using metal tools, which can easily damage any electrical components or circuit boards
they come into contact with.
–
Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed as
electrical insulators.
–
The power supply power cord must include a grounding plug and must be plugged into a
grounded electrical outlet.
–
Serverboard battery: CAUTION - There is a danger of explosion if the onboard battery is
installed upside down, which will reverse its polarities This battery must be replaced only
with the same or an equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
DOC | V1 | 2010.08
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
–
Safety Instructions | en
5
DVD-ROM laser: CAUTION - This server may have come equipped with a DVD-ROM drive.
To prevent direct exposure to the laser beam and hazardous radiation exposure, do not
open the enclosure or use the unit in any unconventional way.
1.5
General Safety Precautions
–
Keep the area around the chassis clean and free of clutter.
–
Place the chassis top cover and any system components that have been removed away
from the system or on a table so that they won’t accidentally be stepped on.
–
While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits or be
pulled into a cooling fan.
–
Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into contact with
printed circuit boards or areas where power is present.
–
After accessing the inside of the system, close the system back up and secure it to the
rack unit with the retention screws after ensuring that all connections have been made.
1.6
System Safety
Electrostatic discharge (ESD) is generated by two objects with different electrical charges
coming into contact with each other. An electrical discharge is created to neutralize this
difference, which can damage electronic components and printed circuit boards. The
following measures are generally sufficient to neutralize this difference before contact is
made to protect your equipment from ESD:
–
Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed as
electrical insulators.
–
Use a grounded wrist strap designed to prevent static discharge.
–
Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready
for use.
–
Touch a grounded metal object before removing any board from its antistatic bag.
–
Do not let components or PCBs come into contact with your clothing, which may retain a
–
Handle a board by its edges only; do not touch its components, peripheral chips, memory
–
When handling chips or modules, avoid touching their pins.
–
Put the serverboard and peripherals back into their antistatic bags when not in use.
–
For grounding purposes, make sure your computer chassis provides excellent
charge even if you are wearing a wrist strap.
modules or contacts.
conductivity between the power supply, the case, the mounting fasteners and the
serverboard.
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
6
en | System Overview
2
1200 Series IP Video Storage System
System Overview
1200 Series chassis features a unique and highly-optimized design, allowing most
configuration of the chassis to be accomplished without tools or screws. The chassis is
equipped with high-efficiency power supply. High-performance fans provide ample optimized
cooling for FB-DIMM memory modules, and four hot-swap drive bays offer maximum storage
capacity.
For information on supported hardware, see the datasheet for the 1200 Series in the Bosch
Online Product Catalog.
For more detailed technical information on your device refer to http://
www.supermicro.com/support/manuals/index.cfm.
There you can download a manual for a 731 model.
DOC | V1 | 2010.08
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
3
System Interface | en
7
System Interface
There are several LEDs on the control panel as well as others on the drive carriers to keep you
constantly informed of the overall status of the system as well as the activity and health of
specific components. The 1200 Series has a power on/off switch, located on the control
panel. This chapter explains the meanings of all LED indicators and the appropriate responses
you may need to take.
1
2
3
4
5
3.1
All-in-One Card Reader
NIC LED
HDD LED
OH LED
Power Button
Control Panel Buttons
Power: The main power button is used to apply or remove power from the power supply to
the system. When the power is on, the power button will be lighted by a blue LED. Turning off
the system power with this button will cause the blue LED to turn off and will remove the
main power, but will keep standby power supplied to the system. Therefore, you must unplug
system before servicing the system.
3.2
Control Panel LEDs
The control panel located on the front of the 1200 Series chassis has three LEDs. These LEDs
provide you with critical information related to different parts of the system. This section
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
8
en | System Interface
1200 Series IP Video Storage System
explains what each LED indicates when illuminated and any corrective action you may need to
take.
HDD: Indicates IDE channel activity. SAS/SATA drive activity when flashing.
NIC1: Indicates network activity on GLAN1 / 2 when flashing.
Overheat/Fan Fail: This LED indicates a fan failure when flashing.
When Continuously On (not flashing): This LED indicates an overheat condition caused by
cables obstructing the airflow in the system or the ambient room temperature being too
warm.
Correcting an Overheat/Fan Fail Condition
1.
Check the routing of the cables and move any cables the restrict airflow.
2.
Confirm that all fans are operating normally.
3.
Verify that the heatsinks are installed properly.
4.
If the chassis cover is not aligned correctly, the airflow may be disrupted. This leads to
overheating. Confirm that the chassis cover is placed correctly.
5.
DOC | V1 | 2010.08
This LED will remain active as long as the overheat condition exists.
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
4
Installation | en
9
Installation
The systems comes pre-installed and only hard drives may be exchanged onsite. In case of any
other failure the entire system has to be exchanged (by advanced exhange).
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
10
en | Chassis Setup and Maintenance
5
1200 Series IP Video Storage System
Chassis Setup and Maintenance
This chapter covers the steps required to install components and perform maintenance on the
chassis. Most components of the 1200 Series do not require tools or screws to set them up.
Those components which must be secured with screws require only a Phillips screwdriver.
Print this chapter to use as a reference while setting-up your chassis.
Review the warnings and precautions listed in the manual before setting up or servicing this
chassis. These include information in Chapter System Safety and the warning/precautions
listed in the setup instructions.
5.1
Removing the Chassis Cover
Removing the Chassis Cover
1.
Push the power button to turn off the power to the system.
2.
Disconnect the chassis from any power source.
3.
Slide the release tab (A) towards the cover handle (B).
4.
Grasp the cover handle with your fingers.
5.
Slide the cover toward the rear of the chassis
6.
Remove the cover from the chassis.
CAUTION!
Except for short periods of time, do NOT operate the system without the cover in place. The
chassis cover must be in place to allow for proper airflow and to prevent overheating.
DOC | V1 | 2010.08
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
5.2
Chassis Setup and Maintenance | en
11
Rotating the Hard Drive Cage
In order to access and install components in the chassis interior, it is necessary to rotate the
hard drive cage. This will provide sufficient room to install and configure the chassis
components.
Rotating the Hard Drive Cage
1.
5.3
Disconnect the chassis from any power source.
2.
Lift the release tab (A).
3.
Rotate the hard disk drive cage (B) outward.
Removing and Installing Hard Drives
The 1200 Series chassis must be powered-down before hard drives can be removed from the
hard drive carriers.
Removing and Installing Hard Drives
1.
2.
Disconnect the chassis from any power source.
Rotate the hard drive cage outward 90 degrees as described in section Rotating the Hard
Drive Cage.
3.
4.
Disconnect all of the cables from the hard drive.
Press the release tab on the side of the hard drive carrier that is to be removed from the
hard drive cage.
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
12
en | Chassis Setup and Maintenance
5.
6.
1200 Series IP Video Storage System
Gently slide the hard drive carrier out of the hard drive cage.
If a hard drive is already present, remove it by carefully pulling the sides of the hard drive
carrier outward.
7.
Remove the hard drive from the hard drive carrier.
8.
Insert the new hard drive into the hard drive carrier.
9.
Insert the hard drive carrier into the hard drive cage, sliding it towards the back of the
the hard drive cage until it clicks into a locked position.
DOC | V1 | 2010.08
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
Chassis Setup and Maintenance | en
13
10. If desired, each hard drive carrier may be secured to the exterior of the hard drive cage
using optional screws.
11. Rotate the hard drive cage 90 degrees inward, returning it to the closed, operational
position in the chassis.
12. Connect the related cables to the hard drives.
5.4
Installing the I/O Shield and Motherboard
Motherboard problems will be handled by trained support people only.
5.5
Installing the System Fan
System fan problems will be handled by trained support people only. If the system fan has to
be replaced the entire unit will be exchanged (advanced exchange service).
Note: The fan noise of the system is a factor to note. When it occurs, this can be an indication
of impending failure of the fan and should be replaced.
5.6
Power Supply
Power Supply Failure problems will be handled by trained support people only. If the power
supply has to be replaced the entire unit will be exchanged (advanced exchange service).
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
en | Appendix
1200 Series IP Video Storage System
A
Appendix
A.1
Motherboard layout
JPUSB1:B/P USB WAKE UP
1-2:ENABLE
2-3:DISABLE
KB/MOUSE
JPI2C:PWR I2C
JPI2C
14
FLOPPY
DIMM1B DIMM1A DIMM2B DIMM2A
DDR3 1066/1333 UDIMM/RDIMM required
JPW1
1
JAR
U26
FAN5
JPB:BMC
1-2:ENABLE
2-3:DISABLE
1
JF1
J6
1
JPB
JPL11
JPL2 1
JI2C1 1
JI2C2 1
JPES
PWR RST
ON
X OH/FF
CPU
JLAN2
NIC2
LAN1
NIC1
HDD PWR
LED LED
JLED1
JD1
JLAN1
SPKR1
1
1
JLED1:Power LED
VGA
1
JTPM
JD1:Buzzer/Speaker
FAN2 FAN1
1
JAR:PSU ALARM RST
COM1
JPUSB1
SLOT7 PCI-E X8 GEN2
J5
FAN3
JI2C1/JI2C2
ON:Enable
OFF:Disable
LE4
BAR CODE
J13
I-SATA1
I-SATA5
I-SATA3
I-SATA4
I-SATA0
I-SATA2
PCI1
JL1:CHASSIS INTRUSION
JPG1
USB 10/11
JPT1:TPM
1-2:Enable
2-3:Disable
JL1
J24
J14
COM2
U61
JPL1:LAN1
1-2:ENABLE
2-3:DISABLE
USB4
USB2/3
1
J16
JPL2:LAN2
1-2:ENABLE
2-3:DISABLE
JPG1: VGA
1-2:Enable
2-3:Disable
JBT1
JBT1:CMOS CLEAR
FAN4 JPT1
MAC CODE
T-SGPIO1 T-SGPIO2
U2
X8SIL
SLOT4 PCI 33MHZ
LE2
REV:1.00
J8
SLOT5 PCI-E X4 on X8
LE3
DESIGNED IN USA
LE7
SLOT6 PCI-E X8 GEN2
DOM PWR
Figure 1.1 Motherboard Layout
Note: All graphics shown in this manual were based upon the latest PCB Revision available at
the time of publishing of the manual. The motherboard you've received may or may not look
exactly the same as the graphics shown in this manual.
Important Notes to the User
–
Jumpers not indicated are for testing only.
–
When LE2 (Onboard Power LED Indicator) is on, system power is on. Unplug the power
cable before installing or removing any components.
DOC | V1 | 2010.08
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
Appendix | en
15
X8SIL/X8SIL-F/X8SIL-V Jumpers
Number
Jumper
Description
Default
38
42
JPUSB1
BP USB0/1 Wake-up
Pins 1-2 (Enabled)
JBT1
CMOS Clear
40
JPES
Energy Saving Feature
13,14
JI2C1/JI2C2
SMB to PCI Slots
17
JPG1
Onboard VGA Enable
Pins 1-2 (Enabled)
11,12
JPL1/JPL2
LAN1/LAN2 Enable
Pins 1-2 (Enabled)
24
JPT1
TPM Enable
Pins 1-2 (Enabled)
10
JPB
BMC Jumper
Pins 1-2 (Enabled)
Pins 2-3 (Disabled)
X8SIL/X8SIL-F/X8SIL-V Headers/Connectors
Number
Connector
Description
4,16
COM1/COM2
COM1/2 Serial connection headers
33,32,27,23,7
Fans 1~5
System/CPU fan headers
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
16
en | Appendix
1200 Series IP Video Storage System
34
Floppy
Floppy Disk Drive connector
5
JAR
Alarm Reset
30
JD1
Speaker header (Pins 3/4: Internal, 1~4:External)
28
JF1
Front Panel Control header
41
JL1
Chassis Intrusion header
29
JLED
Power LED Indicator header
37
JPW1
24-pin ATX main power connector (required)
36
JPW2
+12V 8-pin CPU power connector (required)
1
KB/Mouse
Keyboard/mouse connectors
8,9
LAN1~LAN2,
Gigabit Ethernet (RJ45) ports (LAN1/LAN2)
21
I-SATA 0~5
Serial ATA ports (X8SIL has 4 Serial ATA Ports)
2
IPMI
IPMI LAN Port (X8SIL-F Only)
35
JPI2C
PWR supply (I2C) System Management Bus
31
SPKR1
Internal speaker/buzzer
25
T-SGPIO-0/1
Serial General Purpose IO headers (for SATA)
3,20
USB0/1, USB 2/3
Backplane USB 0/1, Front panel accessible USB 2/
3
19
USB 4
Type A USB Connector
18
USB 10/11
Front Panel USB header (X8SIL-F Only)
22
DOM PWR
Disk-On-Module (DOM) Power Connector
39
JTPM
Trusted Platform Module (TPM) Header
6
VGA
Onboard Video Port
X8SIL/X8SIL-F/X8SIL-V LED Indicators
Number
LED
Description
Color/State
Status
26
LE4
Onboard Standby PWR LED
Green: Solid on
PWR On
15
LE7
IPMI Heartbeat LED (X8SIL-F
Yellow: Blinking
IPMI: Normal
Motherboard Features
CPU
Memory
Single Intel Xeon 3400 series processor in an LGA1156 socket.
Four (4) 240-pin, DDR3 SDRAM DIMM sockets with support for
up to 16GB of UDIMM or up to 32GB of RDIMM memory (ECC/
DDR3 1333/1066/800 MHz memory only.)
Supports dual-channel memory bus
DIMM sizes
Chipset
UDIMM
1 GB, 2 GB, and 4GB
RDIMM
1 GB, 2GB, 4GB, and 8GB
Intel 3420 Chipset (X8SIL-F/X8SIL-V)
Intel 3400 Chipset (X8SIL)
Expansion Slots
Two (2) PCI Express 2.0 (x8) slot
One (1) PCI Express x4 (x8) slot
One (1) 32-bit PCI 33MHz slot
Integrated Graphics
DOC | V1 | 2010.08
Matrox G200eW
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
Network Connections
Appendix | en
17
Two Intel 82574L Gigabit (10/100/1000 Mb/s) Ethernet
Controllers for LAN 1 and LAN 2 ports.
Two (2) RJ-45 Rear IO Panel Connectors with Link and Activity
LEDs
Single Realtek RTL8201N PHY to support IPMI 2.0 (X8SIL-F
Only)
I/O Devices
SATA Connections (X8SIL-F/X8SIL-V Only)
SATA Ports
Six (6)
RAID (Windows)
RAID 0, 1, 5, 10
RAID (Linux)
RAID 0, 1, 10
SATA Connections (X8SIL Only)
SATA Ports
Four (4)
Integrated IPMI 2.0 (X8SIL-F Only)
IPMI 2.0 supported by the WPCM450 Server BMC
Floppy Disk Drive
One (1) floppy drive interface (up to 1.44 MB)
USB Devices (X8SIL Only)
Two (2) USB ports on the rear IO panel
Two (2) USB header connectors for front access
One (1) Type A internal connector
I/O Devices
USB Devices (X8SIL-F/X8SIL-V Only)
(Continued)
Two (2) USB ports on the rear IO panel
Four (4) USB header connectors for front access
One (1) Type A internal connector
Keyboard/Mouse
PS/2 Keyboard/Mouse ports on the I/O backplane
Serial (COM) Ports
Two (2) Fast UART 16550 Connections: one 9-pin RS-232 port
and one header
Super I/O
Winbond Super I/O 83627DHG-P
BIOS
32 Mb SPI AMI BIOS SM Flash BIOS
DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0, USB Keyboard and SMBIOS
2.5
Power Configuration
ACPI/ACPM Power Management
Main switch override mechanism
Keyboard Wake-up from Soft-Off
Internal/External moder ring-on
Power-on mode for AC power recovery
PC Health Monitoring
CPU Monitoring
Onboard voltage monitors for CPU core, +3.3V, +5V, +/-12V,
+3.3V Stdby, +5V Stdby, VBAT, HT, Memory, Chipset
CPU 3-Phase switching voltage regulator
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
18
en | Appendix
1200 Series IP Video Storage System
CPU/System overheat LED and control
CPU Thermal Trip support
Thermal Monitor 2 (TM2) support
Fan Control
Fan status monitoring with firmware 4-pin (Pulse Width
Modulation) fan speed control
Low noise fan speed control
System Management
PECI (Platform Environment Configuration Interface) 2.0
support
System resource alert via Supero Doctor III
SuperoDoctor III, Watch Dog, NMI
Chassis Intrusion Header and Detection
CD Utilities
BIOS flash upgrade utility
Drivers and software for Intel 3400/3420 chipset utilities
Other
ROHS 6/6 (Full Compliance, Lead Free)
Dimensions
Micro ATX form factor, 9.6" x 9.6"
CD Utilities
BIOS flash upgrade utility
Drivers and software for Intel 3400/3420 chipset utilities
Other
ROHS 6/6 (Full Compliance, Lead Free)
Dimensions
Micro ATX form factor, 9.6" x 9.6"
BLOCK DIAGRAM
RoHS 6/6
P5-8
P9
P19
P19
PCIe x8 SLOT
PCIe2.0_x8
PCIe x8 SLOT
PCIe2.0_x8
5.0Gb
5.0Gb
Xeon 3400 Series
(Lynnfield)
DDR3 (CHA)
1333/1066MHz
DIMM1(Far)
DIMM2
P10
Clarkdale
VID[0-7]
DDR3 (CHB)
1333/1066MHz
DIMM1(Far)
DIMM2
4 UDIMM
4 RDIMM
(4 Quad rank
RDIMM run on
800MHz)
x4 DMI
VRM 11.1
MISC VRs
P26-27
P18
PCIe_x4
PCIe x8 SLOT
2.5Gb
P28-29
P11-14
2.5Gbps
P18
IBexPeak
PCI 32
1 PCI 32 SLOT
Intel 3400/3420
P12
SATA-II
4/6 SATA PORTS
USB2.0
5/7 USB PORTS
P15
GLAN1
82574L
PCIe_x1
2.5Gbps
GLAN2
82574L
LPC
PCI32
480Mbps
CK505
Rev1.0
CLOCK
LPC
RJ45
P16
RJ45
P17
P15
TPM1.2
(option)
P30-32
HERMON WPCM450
WINBOND
RMII
SPI
FLASH
SPI 16Mb
P33
LPC
P4
PCH
300MB/s
P21
PCIe_x1
2.5Gbps
P23
COM1,2
P21
P/S2
P20
RTL8201N
PHY
P34
VGA
PORT
P33
RJ45
HEALTH
INFO
W83627DHG
LPC I/O
Figure 1.2 Block diagram
DOC | V1 | 2010.08
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
Appendix | en
19
Note: This is a general block diagram and may not exactly represent the features on your
motherboard. See the Motherboard Features pages for the actual specifications of each
motherboard.
A.2
Chipset Overview
The X8SIL/X8SIL-F/X8SIL-V supports the Intel Xeon 3400 processor series. Built upon the
functionality and the capability of the single-chip Intel 3400 chipset, the X8SIL/X8SIL-F/X8SILV motherboard provides the performance and feature set required for single-processor-based
systems with configuration options optimized for entry-level server platforms.The high-speed
Direct Media Interface (DMI) featured in the Intel 3400/3420 chipset enables the X8SIL/
X8SIL-F/X8SIL-V motherboard to offer a high-speed Direct Media Interface (DMI) for chip-tochip true isochronous communication with the processor. This feature allows the X8SIL/
X8SIL-F/X8SIL-V to achieve up to 10 Gb/s of software-transparent data transfer on each
direction, achieving better performance than comparable systems. The X8SIL/X8SIL-F/X8SIL-V
also features a TCO timer (to enable the system to recover from a software/hardware lock),
ECC Error Reporting, Function Disable and Intruder Detect.
Intel 3400/3420 Chipset Features
–
A.3
Direct Media Interface (up 10 Gb/s transfer, Full Duplex)
–
Intel Matrix Storage Technology and Intel Rapid Storage Technology
–
Dual NAND Interface
–
Intel I/O Virtualization (VT-d) Support
–
Intel Trusted Execution Technology Support
–
PCI Express 2.0 Interface (up to 5.0 GT/s)
–
SATA Controller (up to 3G/s)
–
Advanced Host Controller Interface (AHCI)
PC Health Monitoring
This section describes the PC health monitoring features of the X8SIL/X8SIL-F/X8SIL-V. These
features are supported by an onboard System Hardware Monitor chip.
Recovery from AC Power Loss
BIOS provides a setting for you to determine how the system will respond when AC power is
lost and then restored to the system. You can choose for the system to remain powered off (in
which case you must hit the power switch to turn it back on) or for it to automatically return
to a power on state. See the Power Lost Control setting in the BIOS chapter of this manual to
change this setting. The default setting is Last State.
Onboard Voltage Monitoring
The onboard voltage monitor will scan the following voltages continuously: CPU core, +3.3V,
+5V, +/-12V, +3.3V Stdby, +5V Stdby, VBAT, HT, Memory, Chipset. Once a voltage becomes
unstable, it will give a warning or send an error message to the screen. Users can adjust the
voltage thresholds to define the sensitivity of the voltage monitor by using SD III.
Fan Status Monitor with Software
PC health monitoring can check the RPM status of the cooling fans via Supero Doctor III.
CPU Overheat LED and Control
This feature is available when the user enables the CPU overheat warning feature in the BIOS.
This allows the user to define an overheat temperature. When this temperature reaches this
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
20
en | Appendix
1200 Series IP Video Storage System
pre-defined overheat threshold, the CPU thermal trip feature will be activated and it will send
a signal to the buzzer and, at the same time, the CPU speed will be decreased.
A.4
Power Configuration Settings
This section describes the features of your motherboard that deal with power and power
settings.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking to indicate
that the CPU is in the suspend mode. When the user presses any key, the CPU will wake-up
and the LED indicator will automatically stop blinking and remain on.
BIOS Support for USB Keyboard
If the USB keyboard is the only keyboard in the system, it will function like a normal keyboard
during system boot-up.
Main Switch Override Mechanism
When an ATX power supply is used, the power button can function as a system suspend
button. When the user presses the power button, the system will enter a SoftOff state. The
monitor will be suspended and the hard drive will spin down. Pressing the power button
again to wake-up the whole system. During the SoftOff state, the ATX power supply provides
power the system to keep the required circuitry "alive". In case the system malfunctions and
you want to turn off the power, just press and hold the power button for 4 seconds. The
power will turn off and no power will be provided to the motherboard.
A.5
Power Supply
As with all computer products, a stable power source is necessary for proper and reliable
operation. It is even more important for processors that have high CPU clock rates of 1 GHz
and faster.
The X8SIL/X8SIL-F/X8SIL-V accommodates ATX12V standard power supplies. Although most
power supplies generally meet the specifications required by the CPU, some are inadequate.
A 2-Amp of current supply on a 5V Standby rail is strongly recommended.
It is strongly recommended that you use a high quality power supply that meets ATX12V
standard power supply Specification 1.1 or above. It is also required that the 12V 8-pin power
connection (JPW2) be used for adequate power supply. In areas where noisy power
transmission is present, you may choose to install a line filter to shield the computer from
noise. It is recommended that you also install a power surge protector to help avoid problems
caused by power surges.
The DLA Series does not have a function to determine pre-failure of a power supply. The
power supply will have the LED to show it is “OK” or “failed” by showing the color green or
amber for the respective status. When the power supply fails, it shows amber, when it is
functioning correctly it shows green.
A.6
Super I/O
The disk drive adapter functions of the Super I/O chip include a floppy disk drive controller
that is compatible with industry standard 82077/765, a data separator, write precompensation circuitry, decode logic, data rate selection, a clock generator, drive interface
control logic and interrupt and DMA logic. The wide range of functions integrated onto the
Super I/O greatly reduces the number of components required for interfacing with floppy disk
DOC | V1 | 2010.08
Installation Manual
Bosch Sicherheitssysteme GmbH
1200 Series IP Video Storage System
Appendix | en
21
drives. The Super I/O supports two 360 K, 720 K, 1.2 M, 1.44 M or 2.88 M disk drives and data
transfer rates of 250 Kb/s, 500 Kb/s or 1 Mb/s.
It also provides two high-speed, 16550-compatible serial communication ports (UARTs). Each
UART includes a 16-byte send/receive FIFO, a programmable baud rate generator, complete
modem control capability and a processor interrupt system. Both UARTs provide legacy speed
with baud rate of up to 115.2 Kbps as well as an advanced speed with baud rates of 250 K,
500 K, or 1 Mb/s, which support higher speed modems.
The Super I/O provides functions that comply with ACPI (Advanced Configuration and Power
Interface), which includes support of legacy and ACPI power management through a SMI or
SCI function pin. It also features auto power management to reduce power consumption.
A.7
iSCSI Support
The X8SIL/X8SIL-F/X8SIL-V motherboard supports the iSCSI Internet Protocol. iSCSI is an IP
networking standard used to link and manage data storage, and transfer data across the
internet and private intranets through long distance. iSCSI can be used to transmit data over
local area networks (LANs), wide area networks (WANs), or the Internet. It can enable
location-independent data storage and retrieval.
iSCSI allow clients to issue SCSI commands to remote SCSI storage devices and allow data
centers to consolidate remote storage devices into storage arrays, giving an illusion of locallyattached disks to host servers. Unlike fiber-optic networks that require special cabling, iSCSI
can run over long distance using existing networks.
For the X8SIL/X8SIL-F/X8SIL-V motherboard, iSCSI is supported on LAN 1. This can be
enabled through the BIOS: Advanced => PCI/PnP Configuration => Onboard LAN1 Option
ROM Select.
A.8
Overview of the Nuvoton BMC Controller
The Nuvoton WPCM150 is a combined Baseboard Management Controller and 2D/VGAcompatible Graphics Core with PCI interface, Virtual Media and Keyboard, and a Keyboard/
Video/Mouse Redirection (KVMR) module.
The WPCM150 interfaces with the host system via a PCI interface to communicate with the
Graphics core. It supports USB 2.0 and 1.1 for remote keyboard/mouse/virtual media
emulation. It also provides an LPC interface to control Super I/O functions and connects to
the network via an external Ethernet PHY module or shared NCSI connections.
The Nuvoton BMC communicates with onboard components via six SMBus interfaces, fan
control, Platform Environment Control Interface (PECI) buses, and General Purpose I/O (TSGPIO) ports.
It also includes the following features:
–
One X-Bus parallel interface for expansion I/O connections
–
Three ADC inputs, Analog and Digital Video outputs
–
Two serial for boundary scan and debug
There are two different versions of the Nuvoton BMC chip that are used in this product series.
The Nuvoton WPCM150 (Manufacturer P/N WPCM150GA0BX5) which includes all of the
features above, is the chip installed in the X8SIL motherboard. Another version, the Nuvoton
WPCM450 (Manufacturer P/N WPCM450RA0BX) also has all the features as described above
plus IPMI 2.0 support. This particular chip is installed in the X8SIL-F and X8SIL-V models.
However, IPMI is supported only on the X8SIL-F motherboard.
Bosch Sicherheitssysteme GmbH
Installation Manual
DOC | V1 | 2010.08
22
en | Appendix
DOC | V1 | 2010.08
1200 Series IP Video Storage System
Installation Manual
Bosch Sicherheitssysteme GmbH
Bosch Sicherheitssysteme GmbH
Werner-von-Siemens-Ring 10
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2010