UAB
CDC-697
COMPACT DISC AUTOMATIC CHANGER
OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
• Explanation of Graphical Symbols
1
2
3
4
5
6
7
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
9 Do not defeat the safety purpose of the polarized or
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
10 Protect the power cord from being walked on or
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
IMPORTANT!
Please record the serial number of this unit in the space
below.
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
Model:
Serial No.:
14 Refer all servicing to qualified service personnel.
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES–003.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à la
norme NMB–003 du Canada.
V843150
iiiEn
En
01_En_01_cau-CDC-697_UAB.p65
2
7/12/06, 13:22
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
For U.K. customers
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an appropriate
3 pin plug fitted. For details, refer to the instructions described
below.
Note:
The plug severed from the mains lead must be destroyed, as a plug
with bared flexible cord is hazardous if engaged in a live socket
outlet.
IMPORTANT:
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED. Making sure that neither core is connected to
the earth terminal of the three pin plug.
We Want You Listening For A Lifetime
English
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing
damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume
levels.
iiiii En
En
01_En_01_cau-CDC-697_UAB.p65
3
7/12/06, 13:22
Getting Started
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean place
with at least 10 cm on the top, 10 cm on the left and right, and 10
cm at the back of CDC-697 — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
- Other components, as they may cause damage and/or
discoloration on the surface of this unit.
- Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
- Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all connections are
complete.
8 Do not operate this unit upside-down. It may overheat, possibly
causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of
this unit with a voltage other than specified.
13 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
14 When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
15 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
20 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit must
be set for your local main voltage BEFORE plugging into the AC
wall outlet. Voltages are 110/120/220/230–240 V AC, 50/60 Hz.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
Caution for moving this unit
• When moving this unit, first remove all discs from the disc tray
and close the try by pressing the OPEN/CLOSE button, and
then switch off the power after you confirm that the front panel
display indicates as follows.
2 3 4 5
Never switch off the power if the front panel display is not
pictured as above, otherwise the unit will break down during
moving because the internal mechanism is not locked.
This unit is not disconnected from the AC power source as long
as it is connected to the wall outlet, even if this unit itself is
turned off. This state is called the standby mode. In this state,
this unit is designed to consume a very small quantity of power.
DANGER
When this unit is plugged to the wall outlet, do not place your
eyes close to the opening of the disc tray and other openings to
look into inside.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
16 Before moving this unit, press POWER ON/OFF to release it
outward to the OFF position to turn off this unit, and then
disconnect the power cable from the AC wall outlet.
17 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
18 When using the unit for a long time, the unit may become
warm. Turn the power off, then leave the unit alone for cooling.
19 Install this unit near the wall outlet and where the AC power
plug can be reached easily.
iv En
iii
En
01_En_01_cau-CDC-697_UAB.p65
4
7/12/06, 13:22
ENGLISH
GETTING STARTED
Introduction
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the
best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
Features
● 5-Discs Carousel Auto-changer
● Full Opening Disc Tray for Changing 5 Discs at a Time
PLAYING CDS
● PLAYXCHANGE; Disc Changing Capability while Playing back Another
● Repeat, Random and Program Play
● Remote Control Capability
Contents
Supplied Accessories .......................................... 3
Remote Control Transmitter ................................ 3
Connecting to an Amplifier .................................. 4
Connecting the AC power cable .......................... 5
CONTROLS AND FUNCTIONS ............. 6
PLAYING CDS
BASIC OPERATION .......................... 9
Automatic Tape Programming ........................... 18
Manual Tape Programming ............................... 19
Random Tape Programming ............................. 21
AUTOMATIC PEAK LEVEL SEARCHING .... 22
ADDITIONAL
INFORMATION
Front Panel .......................................................... 6
Remote Control Transmitter ................................ 7
Display ................................................................ 8
FUNCTIONS FOR RECORDING
CD SYNCHRONIZED RECORDING ........ 17
TRACK PROGRAMMING
FOR RECORDING........................... 18
FUNCTIONS FOR
RECORDING
GETTING STARTED
CD PREVENTIVE CARES .................... 2
PREPARATIONS ............................. 3
ADDITIONAL INFORMATION
TROUBLESHOOTING ....................... 23
SPECIFICATIONS ........................... 24
Turning On and Off the Power ............................. 9
Loading and Playing Discs .................................. 9
PLAYXCHANGE ................................................. 10
Scanning Discs ................................................. 10
Skipping Tracks ................................................. 11
Searching .......................................................... 11
CD TEXT ............................................................ 11
VARIOUS FUNCTIONS ..................... 12
Random Sequence Play .................................... 12
Program Play .................................................... 13
Repeat Play ....................................................... 15
Index Search ..................................................... 15
Adjusting the Level ............................................ 16
Timer Play ......................................................... 16
English
1 En
01_En_02_star_CDC-697_UAB.p65
1
7/13/06, 13:20
CD PREVENTIVE CARES
• This compact disc player is designed only for playing
back compact discs bearing the marks shown below.
Never attempt to load any other type of disc into the unit.
The unit can also play back 8 cm (3 inch) compact discs.
Notes
• This unit may not be able to play back some CD-R/CD-RW
discs or discs on which recording was not made correctly.
• This unit is not compatible with a CD-R/CD-RW disc
recorded with MP3 or WMA format.
• Compact discs are not subjected to wear during
playback, but damage to the disc surface when the disc is
being handled can adversely affect the disc playback.
• Do not use cleaning discs or warped discs. All of these
could damage the unit.
• Compact discs are not affected by small particles of dust
or fingerprints on their playing surface, but even so they
should be kept clean. Wipe by using a clean, dry cloth.
Do not wipe with a circular motion; wipe straight
outward from the center.
• Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, anti-static spray or liquid,
or any other chemical-based liquid, because such
substances might irreparably damage the disc’s surface.
• Do not expose discs to direct sunlight, high temperature
or high humidity for a long period of time, because these
might warp or otherwise damage the disc.
To prevent a malfunction of this unit
• Do not use any non standard shaped CD (heart, etc.)
available on the market, because it may damage the unit.
No!
• Do not use a CD with tape, seals, or paste on it, because
damage to the unit may result.
2 En
01_En_02_star_CDC-697_UAB.p65
2
7/12/06, 13:22
GETTING STARTED
PREPARATIONS
Supplied Accessories
Remote Control Transmitter
Batteries (AA, R6, UM-3) x 2
Power cable
(U.S.A., Canada, Australia, U.K. and
Europe models) The shape of the
plug may vary depending on the area
where you purchased.
STANDBY/ON
SYNCHRO DIMMER
OPEN/
CLOSE
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
7
8
9
0
+10
INDEX
MODE
DISC SCAN
REPEAT
- OUTPUT LEVEL
+
Audio Pin Cable
DISC SKIP
RANDOM
CDC8 WH26170
Remote Control Transmitter
■ Battery installation
1
■ Remote control transmitter
operation range
NATURAL SOUND COMPACT DISC PLAYER CDC-697
POWER
3
ON
OFF
PLAYXCHANGE
DISC
STANDBY
/ON
2
1
2
3
4
5
Remote control sensor
■ Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Within approximately
6 m (19.7 feet)
30°
30°
Notes
• Use only AA, R6, UM-3 batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
• Remove the batteries if the remote control transmitter will not
be used for an extended period of time.
• If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Notes
• There should be no large obstacles between the remote
control transmitter and the main unit.
• If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
English
3 En
01_En_02_star_CDC-697_UAB.p65
3
7/12/06, 13:22
PREPARATIONS
Connecting an Amplifier
Never plug in this unit and other components until all connections are completed.
• Before making any connections, switch OFF the power to the unit and the amplifier or other components.
• Connections should be made to the correct input terminals of the amplifier or other components.
• If the placement of this unit causes noise in other equipment, such as a tuner, separate them from each other.
(General model)
LINE OUT
R
L
LINE OUT
R
L
VOLTAGE SELECTOR
RS-232C
REMOTE CONTROL
IN
OUT
230240V
OPTICAL
DIGITAL AUDIO OUT
OPTICAL
REMOTE CONTROL IN/OUT terminals
DIGITAL AUDIO OUT
RS-232C terminal
1 Audio pin cable
(included)
2 Optical cable
(not included)
L
R
OPTICAL
CD
ANALOG IN
DIGITAL IN
Amplifier
Choose one of the ways listed below to connect this unit to your amplifier.
■ When the LINE OUT (analog) terminals of this unit are used (1)
• Be sure that the left (L) and right (R) LINE OUT terminals are connected to the corresponding (left and right) terminals of
the amplifier or other components.
• Connect the LINE OUT terminals to the CD (or AUX) terminals of the amplifier. For additional details concerning these
connections, refer to the operation instructions for the amplifier being used.
■ When the DIGITAL AUDIO OUT (OPTICAL) terminal of this unit is used (2)
• Before using this terminal, remove the terminal cover by pulling it.
• Make the connection from this terminal to the optical input terminal of an amplifier by using a commercially available
optical cable.
* Be sure to use a high quality optical fiber cable. Other cables might not function correctly.
• Be sure to attach the terminal cover when this terminal is not being used in order to protect the terminal from dust.
• Set the level of signals output into an amplifier to max by using the OUTPUT LEVEL –/+ buttons.
For Custom Installer
■ REMOTE CONTROL IN/OUT terminals
These terminals are used for custom installation system. When this unit is connected to the components for custom
installation system, you can operate this unit with the system remote control.
Connect the REMOTE CONTROL IN terminal of this unit to the output terminal of the central controller for custom
installation system.
By connecting the REMOTE CONTROL OUT terminal of this unit to the REMOTE CONTROL IN terminal of the
other component, you can also operate it with the system remote control. In this way, up to 6 components can be
connected in series.
■ RS-232C terminal
This terminal dose not support normal external component connection. This is an expansion terminal for factory use
only.
4 En
01_En_02_star_CDC-697_UAB.p65
4
7/12/06, 13:22
PREPARATIONS
GETTING STARTED
Connecting the power cable
After all other connections are completed, plug the power cable to an AC wall outlet.
• China, Asia and General models
• Other models
AC IN
To AC wall outlet
To AC wall outlet
Plug the power cable into the AC IN, then plug the power
cable to an AC wall outlet.
■ VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the
AC main supply. Voltages are AC 110/120/220/230–240 V, 50/60 Hz.
VOLTAGE SELECTOR
230240V
English
5 En
01_En_02_star_CDC-697_UAB.p65
5
7/12/06, 13:22
CONTROLS AND FUNCTIONS
Front Panel
1
2
3
NATURAL SOUND COMPACT DISC PLAYER CDC-697
POWER
ON
OFF
DISC
STANDBY
/ON
4
1
2
3
5
PLAYXCHANGE
4
5
6
1 POWER ............................................................ P.9
2 Disc tray ............................................................. P.9
3 f (Open/Close) .................................................. P.9
4 STANDBY/ON ................................................. P.9
5 DISC-select ..................................................... P.10
6 Display panel ..................................................... P.8
7
89 0 q w
7 Remote control sensor ....................................... P.3
8 t/e (Skip/Search) ...................................... P.11
9 r/y (Skip/Search) ...................................... P.11
0 w/d (Play/Pause) ............................................. P.10
q a (Stop) ........................................................... P.10
w PLAYXCHANGE ........................................... P.10
6 En
01_En_02_star_CDC-697_UAB.p65
6
7/12/06, 13:22
CONTROLS AND FUNCTIONS
GETTING STARTED
Remote Control Transmitter
STANDBY/ON
1
SYNCHRO DIMMER
2
3
4
OPEN/
CLOSE
t
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
7
8
9
0
+10
INDEX
5
y
u
i
6
MODE
- OUTPUT LEVEL
+
7
DISC SCAN
8
9
0
q
w
e
r
DISC SKIP
REPEAT
RANDOM
o
p
a
s
d
f
1 STANDBY/ON ................................................. P.9
2 SYNCHRO ..................................................... P.17
3 DIMMER ........................................................... P.8
4 TEXT/TIME ....................................................... P.8
5 TAPE ............................................................... P.18
6 Numeric buttons ............................................... P.11
7 Disc play MODE-select ..................................... P.9
8 DISC SCAN ................................................... P.10
9 d (Pause) .......................................................... P.10
0 REPEAT.......................................................... P.15
q w (Play) ............................................................ P.10
w t (Skip) ......................................................... P.11
e a (Stop) ........................................................... P.10
r e (Search) ..................................................... P.11
t OPEN/CLOSE ................................................. P.9
y PEAK .............................................................. P.22
u PROG .............................................................. P.13
i CLEAR ............................................................ P.14
o INDEX ............................................................. P.15
p OUTPUT LEVEL –/+ .................................... P.16
a DISC SKIP ..................................................... P.10
s RANDOM ....................................................... P.12
d y (Skip) ......................................................... P.11
f r (Search) ..................................................... P.11
English
CDC8 WH26170
7 En
01_En_02_star_CDC-697_UAB.p65
7
7/12/06, 13:22
CONTROLS AND FUNCTIONS
Display
The display located in the center of this unit provides
information about discs.
■ Selecting time displays and the text
data
After closing the disc tray by pressing the OPEN/CLOSE
button or selecting any disc by using the DISC SKIP
buttons when this unit is stopped, the display shows the total
number of tracks and the total recorded time of the selected
disc for a few seconds.
You can select any of the four time displays by pressing the
TEXT/TIME display mode-select button. Since this unit is
CD TEXT compatible, the disc title, artist name, and track
name are also displayed in addition to the time displays
when playing back a CD with CD TEXT. Each time you
press the TEXT/TIME display mode-select button, the
display changes as follows.
1 2 3 4 5
12
5DISCS
53:38
1 2 3 4 5
6 7 8 9 10
11 12
■ Display information at disc playback
1
2
1 2 3 4 5
1 Elapsed time of the track now playing back
1 2 3 4 5
5
5DISCS
3
0:08
3
4
3 4 5
6 7 8 9 10
11 12
2
2:35
2 3 4 5
6 7 8 9 10
11 12
2 Remaining time of the track now playing back
1 2 3 4 5
6
1 Encloses the tray number of the selected disc.
2 The numbers corresponding to trays that contain discs
light up after discs are selected.
3 Shows the selected track number.
4 Shows the time displays. (For details, refer to “Selecting
time displays and the text data” on the right column.)
5 Displays the numbers that correspond to the numbers of
the tracks (as high as number 20) on the selected disc.
After each track is played back, its corresponding
number disappears so the number of remaining tracks
(and their numbers) can be seen at a glance.
6 Shows the level of signals output into an amplifier
adjusted by using the OUTPUT LEVEL –/+ buttons.
TEXT/
TIME
5DISCS
2
5DISCS
- 1:02
2 3 4 5
6 7 8 9 10
11 12
3 Total disc playback time
1 2 3 4 5
5DISCS
TOTAL
38:14
2 3 4 5
6 7 8 9 10
11 12
4 Total remaining time on the disc
1 2 3 4 5
5DISCS
TOTAL -32:27
■ Changing brightness of the display
2 3 4 5
6 7 8 9 10
11 12
Disc title
If desired, you can change brightness of the display in three
degrees by pressing the DIMMER button.
Artist name
DIMMER
Track name
when playing back a disc without CD TEXT
when playing back a CD TEXT disc
Notes
• The remaining time 2 will not be displayed if the track
number is 21 or higher.
• The disc title, artist names, or track names may not be
displayed with some CD TEXT discs. In this case,
“NO ENTRY” appears in the display.
8 En
01_En_02_star_CDC-697_UAB.p65
8
7/12/06, 13:22
BASIC OPERATION
This manual describes how to operate this unit by using the
remote control transmitter.
To operate this unit on the front panel, use the
corresponding buttons on the front panel.
Loading and Playing Discs
DISC SCAN
DISC SKIP
STANDBY/ON
Turning On and Off the Power
REPEAT
SYNCHRO DIMMER
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
7
8
9
0
+10
INDEX
RANDOM
1,2
4
PLAYING CDS
POWER
OPEN/
CLOSE
NATURAL SOUND COMPACT DISC PLAYER CDC-697
POWER
ON
OFF
PLAYXCHANGE
DISC
STANDBY
/ON
1
2
3
4
5
3
MODE
DISC SCAN
- OUTPUT LEVEL
+
DISC SKIP
4
STANDBY/ON
STANDBY/ON
REPEAT
SYNCHRO DIMMER
TAPE
OPEN/
CLOSE
TEXT/
TIME
PEAK
CLEAR
PROG
1
■ To turn on this unit
Open the disc tray and load discs.
Use the disc guides to align the discs correctly in the
tray.
Label side upward
Press the POWER button inward to the ON position.
OPEN/
CLOSE
POWER
ON
CDC8 WH26170
RANDOM
OFF
On the front panel
Disc tray
• Press the STANDBY/ON button to set this unit to
the standby mode.
To play back an 8 cm (3 inch) CD, place it in the inner
recessed area of the disc tray. Do not put a normal
(12 cm (5 inch)) CD on top of an 8 cm CD.
STANDBY/ON
STANDBY
/ON
On the remote control
transmitter
On the front panel
• Press the STANDBY/ON button to turn on this unit.
2
Close the disc tray.
OPEN/
CLOSE
STANDBY/ON
STANDBY
/ON
On the front panel
On the remote control
transmitter
Note
You can operate this unit only when the POWER button is
pressed inward to the ON position.
■ To turn off this unit
• You can also close the disc tray by pressing the w/d
button on the front panel, a DISC-select button on
the front panel, a numeric button or the RANDOM
button, or by pressing the front edge of the disc tray
gently. If the tray is closed in these ways, playback
will start automatically, however, the display will not
show the total number of tracks and the total
recorded time of the first selected disc.
Press the POWER button again to release it outward to the
OFF position.
POWER
English
ON
OFF
On the front panel
9 En
01_En_03_play_CDC-697_UAB.p65
9
7/12/06, 13:22
BASIC OPERATION
3
Select a desired disc play mode (1DISC or
5DISCS) confirming it on the display.
MODE
1DISC REP RN
5DISCS S F P
SEARCH TITLE ARTIST
Shows the selected disc mode.
“1DISC” mode: The unit will play back a
designated disc only.
“5DISCS” mode: The unit will play back all discs on
the tray in sequence.
4
PLAYXCHANGE
During playback, you can open the disc tray by pressing the
PLAYXCHANGE button on the front panel without
interrupting disc playback. However, in this case, pressing
the DISC SKIP buttons has no effect. You can load or
replace discs on the trays when the disc tray is opening,
however, never load a disc on the tray hidden inside the unit.
If doing so, the disc and the unit may be damaged, because
the tray already has a disc, which is being played back.
Start playback from the first track of the disc 1.
* If necessary, select a desired disc by using the
DISC SKIP buttons, or a DISC-select button on the
front panel.
DISC
DISC SKIP
or
2
3
4
On the front panel
On the remote control
transmitter
Playback will automatically
start.
Scanning Discs
■ This mode is convenient to search
for a desired disc (or to check discs
on the disc tray)
When the DISC SCAN button is pressed in stop mode, this
unit will play back a section of each disc in turn for 8
seconds.
If, during this playback, you find a disc that you want to
listen to, press the DISC SCAN button once again or press
the w button to cancel this function. The unit will enter into
the normal playback mode.
DISC SCAN
■ To stop playback temporarily
or
Notes
On the remote control
transmitter
On the front panel
To resume playback, press the d button again (or press the
w button).
* The w/d button on the front panel can also be used to
stop playback temporarily or to resume playback.
• During this playback, the disc tray numbers blink in the
display. Every time the playback of a disc is finished, the
corresponding tray number is changed from flashing to
lighting.
• If the disc being played back has a long blank space between
tracks, you will hear no sound during disc scan.
■ To stop playback completely
or
On the front panel
On the remote control
transmitter
10 En
01_En_03_play_CDC-697_UAB.p65
10
7/12/06, 13:22
BASIC OPERATION
Skipping Tracks
Searching
■ To play back from the beginning of
the track following the one now
playing back
■ To go forward rapidly
(Press and hold.)
■ To go backward rapidly
■ To play back from the beginning of
the track before the one now
playing back
(Press and hold.)
• The sound can be heard (although slightly garbled)
during manual search in either direction. This is
convenient for locating a precise position within a track,
or for reviewing the contents quickly.
• Manual search can also be performed while disc
playback is paused. In this case, no sound will be heard.
PLAYING CDS
■ To play back from the beginning of
the track now playing back
CD TEXT
(Twice)
• These operations can also be performed when the unit is
paused or stopped.
• When using the t or y button on the remote control
transmitter:
* If the button is pressed and held, the track number is
continuously changed to higher numbers (or lower
numbers).
This unit is compatible with the CD TEXT function. The
CD TEXT disc has information, such as the disc title, artist
names, and track names. If the current disc is a CD TEXT
disc, the unit reads the disc title, artist name, and track
names from the disc. You can display the CD TEXT data
(see “Selecting time displays and the text data” on page 8).
■ DIRECT PLAY
Select a desired track by using the numeric buttons.
1 2 3 4 5
2
3
4
5
6
7
8
9
0
—10
—
1
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
11 12 13 14 15
16 17 18 19
5
The selected track number is displayed.
Example: To select track 25
English
Press +10 twice, then immediately press 5 once.
* If a track number higher than the highest track number
on the disc is selected, the last track on the disc will be
played back.
11 En
01_En_03_play_CDC-697_UAB.p65
11
7/12/06, 13:22
VARIOUS FUNCTIONS
Random Sequence Play
You can play back the tracks on one or more discs in a
random sequence. The unit will automatically mix up tracks
from all discs or a designated disc on the disc tray.
DISC SCAN
4
Press the RANDOM button.
RANDOM
DISC SKIP
STANDBY/ON
REPEAT
SYNCHRO DIMMER
3
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
8
9
0
+10
INDEX
MODE
- OUTPUT LEVEL
REPEAT
RANDOM
4
1,2
“RNDM” lights up in the display.
■ To cancel random-sequence play
Press the a button or RANDOM button once again, or open
the disc tray by pressing the OPEN/CLOSE button.
“RNDM” disappears from the display.
7
DISC SCAN
1
OPEN/
CLOSE
Notes
+
DISC SKIP
CDC8 WH26170
RANDOM
Load one or more discs.
• This feature will not function during programming, or during
program play.
• If the y button is pressed during random-sequence play, the
next randomly programmed track will be played back. If the
t button is pressed, playback will return to the beginning of
the track now being played back.
• This indication appears while the unit is mixing up tracks.
OPEN/
CLOSE
• Total remaining time on the disc will not be displayed during
random-sequence play.
2
Close the disc tray.
OPEN/
CLOSE
3
Select a desired disc play mode (1DISC or
5DISCS).
MODE
* If you select “1DISC” mode, next select a desired
disc by using the DISC SKIP buttons on the remote
control transmitter or a DISC-select button on the
front panel.
12 En
01_En_03_play_CDC-697_UAB.p65
12
7/12/06, 13:22
VARIOUS FUNCTIONS
Program Play
You can enjoy listening to your favorite tracks selected from
one or more discs in any desired order by programming
tracks.
DISC SCAN
4
If necessary, select a desired disc.
DISC
DISC SKIP
or
2
3
4
DISC SKIP
STANDBY/ON
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
7
8
9
0
+10
INDEX
MODE
- OUTPUT LEVEL
DISC SCAN
REPEAT
1
2
On the remote control
transmitter
7
1
3
5
+
DISC SKIP
2,4
On the front panel
Program a desired track by pressing the
corresponding numeric button.
1
2
3
4
5
6
7
8
9
0
—10
PLAYING CDS
5
RANDOM
OPEN/
CLOSE
—
REPEAT
SYNCHRO DIMMER
CDC8 WH26170
RANDOM
Stop the unit.
6
Repeat steps 4 and 5 to program more tracks.
You can select the same track again.
7
When the programming is completed, start the
playback.
If you will select tracks from a disc (or discs)
other than the disc on the Disc 1 tray, make this
unit display the total recorded time of each disc
to be used by pressing the DISC SKIP buttons
in turn.
* Without this operation, the total time of the
programmed tracks will not be displayed during
programming.
DISC SKIP
3
Press the PROG button to start programming.
PROG
5
1DISC REP RNDM SAVE BEST EDIT
5DISCS S F PROG CD- TEXT 1 2
SEARCH TITLE ARTIST TRACK
6 7
STEP
1
11 12
16 17
English
13 En
01_En_03_play_CDC-697_UAB.p65
13
7/12/06, 13:22
VARIOUS FUNCTIONS
■ Display information during
programming
1 2 3 4 5
--
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
STEP
1
11 12 13 14 15
16 17 18 19 20
2
-6
Press the a button. The first programmed track number will
be displayed.
To resume playback, press the w button. Playback will start
from the beginning of the program.
■ To cancel a programmed sequence
1
4
1 2 3 4 5
■ To stop program play
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9
STE 3:25
11 12 13 14 15
16 17 18 19 20
3
1 Shows the program number for the track to be
programmed next.
2 Shows the selected disc and track number.
3 Shows the total time of the tracks currently
programmed.
4 Shows only the numbers of programmed tracks on the
selected disc.
* If “STEP 1” does not appear on the display after the
PROG button is pressed, press the TEXT/TIME display
mode-select button.
* If the total time exceeds 99 minutes and 59 seconds, the
time will not be displayed.
Notes
• You can program as many as 40 tracks at one time.
• You can program a whole disc by pressing “0”, instead of one
track. At that time, “ALL” lights up in the display.
• The total time of the programmed tracks will not be
displayed, if a track number higher than 20 is programmed.
• If, during programming, the TEXT/TIME display modeselect button is pressed, the program number display can be
changed to display the total time of the programmed tracks or
no information. To return to the previous display, press the
TEXT/TIME display mode-select button once again.
• The t and y buttons can be used during playback, but
only within the range of the programmed tracks.
• Pressing a numeric button stops the current program and
skips to the beginning of the track of the number pressed.
Once that track has finished playback, the previously
interrupted program resumes playback.
• The e and r buttons can be used during playback to
search all tracks, including unprogrammed tracks.
There are several methods, as described below.
• Press the a button or the CLEAR button while the unit
is stopped.
• Open the disc tray.
• Press the STANDBY/ON button.
• Switch off the power.
■ To check program data
1 During program play, press the a button.
2 Press the PROG button.
3 Each time the y button is pressed, the track numbers
and sequential order of the programmed tracks can be
checked one after another. The display of the track
number can be returned (sequentially in reverse order) by
pressing the t button.
■ To correct program data
1 Follow the procedure described in “To check program
data”.
2 Display the track number to be corrected by pressing the
t or y button.
3 Press a numeric button to select a track to replace the one
displayed. The previously programmed track will be
cleared from the memory and the new one will be
programmed.
4 After the correction has been completed, press the
PROG button or w button once again.
14 En
01_En_03_play_CDC-697_UAB.p65
14
7/12/06, 13:22
VARIOUS FUNCTIONS
Repeat Play
Index Search
You can play back any desired track or disc (or a set of
discs) repeatedly by pressing the REPEAT button. The
repeat play mode will change whenever you press the
REPEAT button.
If the disc includes index numbers, playback can be started
from any desired index number.
1
Select a track which has index numbers.
(Off)
1
2
3
4
5
6
7
8
9
0
—10
PLAYING CDS
—
REPEAT
1DISC REP RNDM SA
5DISCS S F PROG C
RCH TITLE ARTIST TRAC
2
Press the INDEX button.
INDEX
1DISC REP RNDM SA
5DISCS S F PROG C
RCH TITLE ARTIST TRAC
■ REP S (Single repeat)
A single track is repeatedly played back.
* This is also available in the program play mode and the
random-sequence play mode. (If the repeat play mode is
switched off, the program play mode or the randomsequence play mode will be resumed.)
1 2 3 4 5
5
3
INDEX 1
11 12
Select the desired index number.
■ REP F (Full repeat)
In the “1DISC” disc play mode: A designated disc is
repeatedly played back.
In the “5DISCS” disc play mode: All discs on the disc tray
are repeatedly played back.
* In the program play mode, all programmed tracks are
repeatedly played back.
* In the random-sequence play mode, all randomly
sequenced tracks on a designated disc (1DISC) in the
same order, or all randomly sequenced discs and tracks
(5DISCS) are repeatedly played back.
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
3
1DISC REP RNDM SAVE BEST
5DISCS S F PROG CD- TEXT
SEARCH TITLE ARTIST TRACK
IDX 3
13 14 15
16 17 18 19 20
■ To cancel the index search function
Press the INDEX button.
Notes
• Not all discs have index numbers. The index system has a
method for sub-dividing tracks into smaller divisions (for
example, the movements within classical symphonies) for
easier location of those parts. The liner notes with the disc
usually tell if such index numbers are included.
• If an index number is selected that is higher than any index
number on that disc, playback will start from the last index
number point on the disc.
• For some discs, playback may start slightly prior to the actual
designated index point.
• If the disc has no encoded index points, playback will start
from the beginning of the selected track.
English
15 En
01_En_03_play_CDC-697_UAB.p65
15
7/12/06, 13:22
VARIOUS FUNCTIONS
Adjusting the Level
■ Adjusting the level of signals output
into an amplifier, etc.
You can adjust the level of sound signals output from the
LINE OUT terminals on the rear panel into an amplifier,
etc.
—
— OUTPUT LEVEL —
For optimum sound quality
* When the DIGITAL AUDIO OUT (OPTICAL) terminal
is used for the connection, set the level of output signals
to max.
* The level of output signals can be checked in the display.
CK
6 7 8 9 10
11 12 13 14 15
16 17 18 19 20
Timer Play
You can start playback at any specified time by connecting a
timer (sold separately). (For details, refer to the owner’s
manual of the timer.)
1 Select the desired play mode (1DISC or 5DISCS).
2 Press the POWER button to turn the unit off.
3 Press the POWER button while pressing the w/d button
on the front panel.
Shortly thereafter, “TIMER P. ON” appears in the
display and the timer play function is on.
(When the timer play function is already on, in which
case, “TIMER P. OFF” appears in the display and timer
play function is off. In this case, repeat the procedure in
steps 2 and 3 to set the timer play function to on.)
4 Set the timer to the desired time.
When the set time comes, the unit turns on and starts
playback.
NATURAL SOUND COMPACT DISC PLAYER CDC-697
POWER
ON
OFF
PLAYXCHANGE
DISC
STANDBY
/ON
1
2
3
4
5
2,3
3
16 En
01_En_03_play_CDC-697_UAB.p65
16
7/12/06, 13:22
CD SYNCHRONIZED RECORDING
DISC SCAN
4
If desired, select the track to be recorded first.
1
2
3
4
5
6
7
8
9
0
—10
DISC SKIP
or
5
—
Using a compatible YAMAHA tape deck, you can
synchronize the tape deck to start recording automatically
when this unit starts playback. With this function, you can
record a CD on tape more easily and precisely. (For details,
refer to the operation manual of the tape deck to know
whether it is compatible or not.)
* This unit and the tape deck must be placed close to each
other so that both of them can receive the signals from the
remote control transmitter of this unit at the same time.
Press the w button.
DISC SKIP
STANDBY/ON
REPEAT
3
SYNCHRO DIMMER
RANDOM
OPEN/
CLOSE
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
5
Both CD playback and tape deck recording start.
* CD playback starts a little later than recording.
6
7
8
9
0
+10
INDEX
MODE
DISC SCAN
- OUTPUT LEVEL
REPEAT
■ To cancel this function
+
DISC SKIP
Press the a button.
1
CDC8 WH26170
RANDOM
Notes
1
Select a disc.
DISC SKIP
2
Load a tape on the tape deck.
* The peak level searching function of this unit is
useful for adjusting recording level on the tape deck.
(For details, refer to page 22.)
3
Press the SYNCHRO button.
• To finish or stop recording, press the a button on the tape
deck.
• Programmed sequence of tracks can also be recorded with
this function, instead of recording an entire disc. (For details,
refer to pages 13 to 14.)
• This function can also be used together with the tapeprogramming function. (For details, refer to pages 18 to 21.)
FUNCTIONS FOR
RECORDING
4
If you want to stop recording temporarily and
restart recording from a desired track, follow
steps 3 to 5 again.
SYNCHRO
This unit enters into the pause mode, and the tape deck
enters into the REC/PAUSE mode.
* In this mode, the time display on this unit blinks.
English
17 En
01_En_04_func_CDC-697_UAB.p65
17
7/12/06, 13:22
TRACK PROGRAMMING FOR RECORDING
This convenient feature can be used to program tracks for
recording to tape. By only memorizing the total possible
recording time of the tape, the unit will automatically
program tracks or help you to program tracks so they will fit
onto the tape with the least amount of unrecorded space
remaining at each end of the tape.
The peak level searching function of this unit is useful for
adjusting recording level on the tape deck. (For details, refer
to page 22.)
You can select any of four tape lengths by pressing the
TAPE button.
TAPE
(Off)
Automatic Tape Programming
You can also enter the total possible recording time of
the tape manually.
Example: For a C-64 tape (32 minutes on each side)
The unit will automatically program tracks on a disc with
the original order of tracks unchanged.
DISC SCAN
6
4
1
2
DISC SKIP
64
STANDBY/ON
SYNCHRO DIMMER
3
REPEAT
RANDOM
PEAK
5
TAPE
CLEAR
PROG
1
1
2
3
4
5
6
7
8
9
0
+10
INDEX
MODE
- OUTPUT LEVEL
4
The unit automatically programs tracks for side A and
side B separately considering the total time of the tape.
* The programmed track numbers and the total number
of tracks for side A and B are displayed for a short
time.
2
CDC8 WH26170
RANDOM
Stop the unit.
Select the disc.
Press the REPEAT button.
REPEAT
+
DISC SKIP
REPEAT
2
4
TEXT/
TIME
DISC SCAN
1
OPEN/
CLOSE
5
Start recording on the tape deck and press the
w button at the same time.
6
The unit will pause at the end of side A of the
tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the w or d button.
DISC SKIP
Notes
3
Enter the total possible recording time of the
tape (tape length).
TAPE
46
• It is recommended that you use a tape that is slightly longer
in length than the CD you are recording, because the
programmed tracks on a CD may not fit properly into the
time allowed on each half of the tape.
• CD synchronized recording function can be used if your tape
deck is compatible with it. In this case, in step 5 and 6, press
the SYNCHRO button and then press the w button.
Recording automatically starts. (For details, refer to page 17.)
18 En
01_En_04_func_CDC-697_UAB.p65
18
7/12/06, 13:22
TRACK PROGRAMMING FOR RECORDING
■ Display information during
programming
3
1 2 3 4 5
Manual Tape Programming
With this function, you can program tracks from one or
more discs in any order to be recorded onto tape.
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
5
20:00
DISC SCAN
REPEAT
SYNCHRO DIMMER
1
DISC SKIP
STANDBY/ON
11 12 13 14 15
16 17 18 19 20
2
1 Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished,
and then it is replaced by the number of the first
programmed track for side A.
2 Shows the total time of programmed tracks for each side.
3 Shows the programmed track numbers for each side.
8
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
7
8
9
0
+10
INDEX
6
MODE
DISC SCAN
- OUTPUT LEVEL
1
4
+
DISC SKIP
REPEAT
RANDOM
OPEN/
CLOSE
2,5
CDC8 WH26170
RANDOM
Stop the unit.
2
If you will select tracks from a disc (or discs)
other than the disc on the Disc 1 tray, make this
unit display the total recorded time of each disc
to be used by pressing the DISC SKIP buttons
in turn.
* This unit will read the contents of a disc by this
operation. If there is a disc to which this operation is
omitted, tracks on the disc cannot be programmed.
3
4
Follow step 3 on page 18.
FUNCTIONS FOR
RECORDING
1
Press the PROG button.
PROG
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4
H TITLE ARTIST TRACK
6 7 8 9
2A-01
11 12 13 14
16 17 18 19
5
If necessary, select a desired disc by pressing
the DISC SKIP buttons.
6
Select a desired track.
2
3
4
5
6
7
8
9
0
—10
—
1
English
19 En
01_En_04_func_CDC-697_UAB.p65
19
7/12/06, 13:22
TRACK PROGRAMMING FOR RECORDING
7
8
Repeat steps 5 and 6 to program more tracks
for side A of the tape.
You can select the same track again.
* If “ERROR” appears in the display, the track number
just selected cannot be programmed because there is
no enough time remaining on side A of the tape.
When you finish the programming for side A,
program the pause mode by pressing the TAPE
button.
■ Display information during
programming
1 2 3 4 5
--
2
1 2 3 4 5
-4
9
Repeat steps 5 and 6 to program more tracks
for side B of the tape.
You can select the same track again.
* If “ERROR” appears in the display, the track number
just selected cannot be programmed because there is
no enough time remaining on side B of the tape.
Start recording on the tape deck and press the
w button at the same time.
The unit will pause at the end of side A of the
tape. Turn the tape over to side B. Resume
recording and, at the same time, press the w or
d button.
Notes
A- 1
4
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
- 8:28
3
* If “A-1” does not appear in the display after the PROG
button is pressed, press the TEXT/TIME display modeselect button.
* If, during programming, the TEXT/TIME display modeselect button is pressed, the program number display can
be changed to display the total remaining time on the
side of the tape. To return to the previous display, press
the TEXT/TIME display mode-select button once again.
Notes on tape programming
• You can check, cancel or correct program data. (For
details, refer to page 14.)
• The maximum number of tracks that can be programmed
is 40. If, however, the PAUSE mode is inserted, it is
counted as one track.
• This function can be used to program up to track number
20. If the disc has more than 20 tracks, tracks with track
number 21 and higher cannot be programmed.
20 En
20
11 12 13 14 15
16 17 18 19 20
1 Shows the side of the tape and the program number for
the track to be programmed next.
2 Shows the selected disc and track number.
3 Shows the total remaining time on the side of the tape.
4 Programmed track numbers light up and programmable
track numbers among the unprogrammed ones blink.
• In steps 7 and 9, even if “ERROR” appears in the display, you
can program another track of which time is shorter than the
remaining time on the side of the tape. At this time, if any
other track number lights up in the display, you can program
it.
• CD synchronized recording function can be used if your tape
deck is compatible with it.
In this case, in steps 10 and 11, press the SYNCHRO button
and then press the w button. Recording automatically starts.
(For details, refer to page 17.)
01_En_04_func_CDC-697_UAB.p65
11 12 13 14 15
16 17 18 19 20
1
TAPE
* “PAUSE” lights up in the display.
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
7/12/06, 13:22
TRACK PROGRAMMING FOR RECORDING
Random Tape Programming
The unit will automatically program tracks on a disc in
random sequential order for recording to tape.
DISC SCAN
REPEAT
DISC SKIP
RANDOM
2
3
Notes
• Because the programmed data changes every time the
RANDOM button is pressed, the amount of time remaining
at the end of the tape also changes accordingly.
• It is recommended that you use a tape that is slightly longer
in length than the CD you are recording, because the
programmed tracks on a CD may not fit properly into the
time allowed on each half of the tape.
• CD synchronized recording function can be used if your tape
deck is compatible with it.
In this case, in steps 3 and 4, press the SYNCHRO button
and then press the w button. Recording automatically starts.
(For details, refer to page 17.)
Display information during programming
3
CDC8 WH26170
1 2 3 4 5
Follow steps 1 to 3 on page 18.
RANDOM
The unit will automatically program tracks for side A
and side B separately considering the total time of the
tape.
* The programmed track numbers and the total number
of tracks for side A and B are displayed for a short
time.
3
Start recording on the tape deck and press the
w button at the same time.
4
The unit will pause at the end of side A of the
tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the w or d button.
3
5
13:00
1
2
1 Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished,
and then it is replaced by the number of the first
programmed track for side A.
2 Shows the total time of programmed tracks for each side.
3 Shows the programmed track numbers for each side.
FUNCTIONS FOR
RECORDING
Press the RANDOM button.
1
7
4
1
2
PROG
English
21 En
01_En_04_func_CDC-697_UAB.p65
21
7/12/06, 13:22
AUTOMATIC PEAK LEVEL SEARCHING
This unit automatically searches for the peak level of the
disc, and play back the part repeatedly. When recording to
tape, this feature is very helpful for adjusting the recording
level on the tape deck.
DISC SCAN
4 Press the PEAK button.
PEAK
DISC SKIP
STANDBY/ON
REPEAT
SYNCHRO DIMMER
TEXT/
TIME
PEAK
TAPE
CLEAR
PROG
1
2
3
4
5
6
7
8
9
+10
INDEX
0
MODE
RANDOM
OPEN/
CLOSE
- OUTPUT LEVEL
4
1 2 3 4 5
1
REPEAT
The peak level search is performed on the disc.
1 2 3 4 5
+
DISC SKIP
2
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
P8AK
0:44
11 12 13 14 15
16 17 18 19 20
3
CDC8 WH26170
RANDOM
1 2 3 4 5
1
11 12 13 14 15
16 17 18 19 20
PEAK
2
DISC SCAN
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
Stop the unit.
1DISC REP RNDM SAVE BEST EDIT FILE
5DISCS S F PROG CD- TEXT 1 2 3 4 5
SEARCH TITLE ARTIST TRACK
6 7 8 9 10
PEAK
Select the “1DISC” disc play mode.
MODE
4 5
1DISC REP RNDM SAVE BES
S F PROG CD- TEX
ARTIST TRACK
SEARCH TITLE
00:44
11 12 13 14 15
16 17 18 19 20
After searching, this unit plays back the part around the
peak level.
According to the peak level, adjust the recording level
on your tape deck. (For details, refer to the owner's
manual of the tape deck.)
■ To cancel this function
Press the a button.
3
Select the disc.
DISC SKIP
Notes
• Even if the peak level search is performed twice or more on
the same disc, the same part will not be always selected,
because this unit will search for the peak level among parts
on the disc that are randomly selected by the internal
microcomputer.
• In the program play mode, this feature will function among
the programmed tracks only. If program play is being
performed, first press the a button, and then press the PEAK
button. If program play is not being performed, only press the
PEAK button.
• To search for the peak level through all discs on the disc tray,
in step 2, select the “5DISCS” disc play mode.
22 En
01_En_04_func_CDC-697_UAB.p65
22
7/12/06, 13:22
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the problem can be corrected by the
simple measures suggested. If it cannot, or if the problem is not listed in the SYMPTOM column, disconnect the unit’s power
cord and contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
This unit fails to turn on or enters
the standby mode soon after the
power is turned on.
This unit does not work normally.
The disc tray does not close
completely.
A disc number does not light up
on the display.
PROBABLE CAUSE
The power cord is not connected or not
completely connected.
REMEDY
Securely connect the power cord.
There is an influence of strong external noise
(lightning, excessive static electricity, etc.) or
an incorrect operation was performed while
using this unit.
A foreign object is obstructing the tray.
Turn off and disconnect the AC power from
the AC wall outlet. After about 30 seconds,
connect the power and try again.
The disc has been loaded upside down.
The disc is damaged.
Reload the disc with the label side up.
Check the disc carefully; replace it if
necessary.
Wait 20 to 30 minutes after switching the unit
ON before trying to play back a disc.
Check the disc carefully; replace it if
necessary.
There is moisture on the laser pickup.
Playback does not start.
The disc is damaged.
Playback is delayed, or starts at
the wrong place.
No sound.
The disc has been loaded upside down.
The disc is dirty.
The disc may be scratched or damaged.
Improper output cable connections.
Improper amplifier operation.
This unit is being subjected to vibrations or
impacts.
The disc is dirty.
Improper cable connections.
Sound “hums”.
Noise from a nearby tuner.
Noise from inside of the disc tray.
The remote control transmitter
does not work.
The tuner is too close to this unit.
The disc may be warped.
The batteries of this remote control
transmitter are too weak.
Direct sunlight or lighting (of an inverter type
of fluorescent lamp, etc.) is striking the
remote control sensor of the main unit.
Reload the disc with the label side up.
Clean the disc.
Check the disc carefully; replace it if
necessary.
Connect the cables properly. If the problem
persists, the cables may be defective.
Set the amplifier controls to the correct input
selection.
Relocate this unit.
Clean the disc.
Securely connect the audio cables. If the
problem persists, the cables may be defective.
Move the tuner and this unit farther apart.
Replace the disc.
Replace the batteries with new ones.
ADDITIONAL
INFORMATION
Sound “skips”.
Carefully check the disc tray and remove the
foreign object.
Change position of the main unit.
English
23 En
01_En_05_addi_CDC-697_UAB.p65
23
7/12/06, 13:22
SPECIFICATIONS
Audio Section
General
Frequency response ...................... 10 Hz – 20 kHz, ± 0.5 dB
Power requirements
U.S.A. and Canada models .......................... 120 V, 60 Hz
Australia model ........................................... 240 V, 50 Hz
Europe and U.K. models ............................. 230 V, 50 Hz
Asia and General models
................................... 110/120/220/230-240 V, 50/60 Hz
China model ................................................ 220 V, 50 Hz
Harmonic distortion + noise (1 kHz) ......................... 0.003%
S/N ratio .................................................................... 106 dB
Dynamic range ............................................................. 96 dB
Output level (1 kHz, 0 dB) .................................. 2.0 ± 0.5 V
Power consumption ...................................................... 12 W
Laser Diode Properties
Type ........................................ Semiconductor laser GaAlAs
Wavelength ................................................................ 790 nm
Output Power ................................................ 1.23 mW (max)
Dimensions (W x H x D) ...................... 435 x 116 x 403 mm
(17-1/8” x 4-9/16” x 15-7/8”)
Weight ............................................... 5.5 kg (12 lbs. 125 oz.)
Please note that all specifications are subject to change
without notice.
24 En
01_En_05_addi_CDC-697_UAB.p65
24
7/12/06, 13:22
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION – VISIBLE AND / OR INVISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO BEAM.
VARNING – SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO !
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE.
ÄLÄ KATSO SÄTEESEEN.
VARNING – SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE
LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET.
NICHT DEM STRAHL AUSSETZEN.
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
GE
LTA
VO
OR
CT
LE
SE
240V
(Example: General model)
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID EXPOSURE TO BEAM.
LINE OUT
R
L
VOLTAGE SELECTOR
RS-232C
REMOTE CONTROL
IN
OUT
230240V
OPTICAL
DIGITAL AUDIO OUT
(Example: General model)
00_CV4_CDX-697_UAB.p65
1
7/12/06, 13:22
00_CV4_CDX-697_UAB.p65
2
7/12/06, 13:22
00_CV4_CDX-697_UAB.p65
3
7/12/06, 13:22
© 2006
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
00_CV4_CDX-697_UAB.p65
4
7/12/06, 13:22
All rights reserved.
Printed in Malaysia
WH52590