advertisement
Specifications
Environment
Devices
Transmission
Standard supported
PoE Power
Connectors
LED Indicators
Maximum Distance
RJ45 Pin Configuration
Reverse Polarity
Sensitive. Use EIA/TIA
568A or 586B straightthrough wiring.
PoE CCTV IP
PoE CCTV IP cameras with a 10/100Mb/s Ethernet port, using up to
15.4 Watts.
Transparent to the user
Ethernet side:
IEEE 802.3 10BaseT,
IEEE 802.3U 100Base-TX
IEEE 802.3af compatible PoE
Class 3
One (1) BNC 75 Ohms.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.
Power, IP Traffic, 100MBps
RG59/RG6:
UTP Cat 5e/6:
Up to 980 ft (300m) @ 100Mbps
Up to 330 ft (100 m)
Note: When installed in an electrically noisy environment, an STP cable must be used. Also, cross-connection reduces the effective distance depending on the grade of twisted cable used.
RJ45 Link
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
Cable
PoE Power Supply
(500113)
Power Consumption
Temperature
Enclosure
Accessories
Dimensions
Weight
Compliance
Warranty
Order Information
UTP/STP: One (1) Cat 5e/6 or better twisted pair cables required
RG59/RG6: 75 Ohms (avoid CCS cable)
Optional PoE Power Supply (110-240V/48VDC/.625A, 2.1mm plug) with inter-changeable blades (sold separately). Required at the Camera
Side Device when coax cable quality or length results in insufficient power reaching the camera. Required at the Network Side Device when used with non-PoE LAN switch.
Network Side: 1.82 Watt Camera Side: 1.73 Watt
Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Metal
Wall-mount brackets included
4.37” x 2.95” x 0.99” (110 x 75 x 25 mm)
1.5 lb (0.68 kg)
Regulatory: FCC, CE, RoHS
2 years
Flammability: 94V0
500112 LongReach CCTV IP PoE Extender Kit
500113 Power Supply for 500112 (48VDC)
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: [email protected] URL: www.muxlab.com
© MuxLab Inc.
94-000749-A SE-000749-A
LongReach CCTV IP PoE Extender Kit
500112
Quick Installation Guide
Overview
The LongReach CCTV IP PoE Extender Kit (500112) allows one IP camera (15.4
Watts) to be connected up to 980 ft (300 m) via a single 75-ohm coax cable in a pointto-point configuration. The maximum distance depends on the grade and quality of coaxial cable. An optional PoE 48VDC Power Supply (500113) is available if required.
Applications
CCTV IP surveillance
Installation
1. Identify the connectors on the Extenders as indicated on the product labels.
2. Attach the surface-mount brackets if required as shown below.
3. Verify that the distance between the CCTV IP PoE extenders is within MuxLab specifications (see Specifications table).
4. To install the Network Side Device:
3a. Connect the extender to the PoE Ethernet Switch with a UTP Cable.
Note: If the Ethernet Switch is not PoE; you will need to connect a PoE Power
Supply (500113) to the Network Side Device.
3b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX
LINK connector on the Extender.
5. To install the Camera Side Device:
4a. Connect the extender to the camera with a Cat5e/6 cable.
Note: If the quality or length of the coaxial cable reduces the power to a level that is insuffiicent to power the camera, you will need to connect a PoE Power Supply
(500113) to the Camera Side device.
4b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX
LINK connector on the Extender.
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions in respect to the installation of the CCTV IP PoE Coax Extender Kit:
Symptom
No Image
Network Side Camera Side
LEDs LEDs
Power IP Traffic Power IP Traffic
OFF OFF OFF OFF
Probable Cause
No power
Possible
Solutions
No Image
No Image
No Image
No Image
ON
ON
ON
ON
Choppy Image ON
OFF
OFF
OFF
ON
BLINK
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
ON
Coaxial Cable
Distance
UTP Cable
No Traffic
BLINK Distance
• Check if the Ethernet switch is PoE.
• Check the power connection.
• Check the coaxial cables.
• Check the coaxial cables length and quality.
• Check the UTP Cable pin out.
• Check network configuration.
• Check cable length
• Check the coaxial cable quality.
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).
6. Power on the equipment and verify the image quality. The following is a diagram of a typical configuration.
© MuxLab Inc. 2013
advertisement
Related manuals
advertisement