Emerson CF805SWW01 Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
CONTEMPORARY SNUGGER™
Ceiling Fan Owner's Manual
42” Model Numbers
52” Model Numbers
CF805SAB01 - Antique Brass
CF805SAW01 - Summer White
CF805SBS01 - Brushed Steel
CF805SORB01 - Oil Rubbed
CF804SBS01 - Brushed Steel
CF804SORB01 - Oil Rubbed
Bronze
CF804SWW01 -
Appliance
White
Bronze
CF805SWW01 Net Weight:
Appliance
White
13.9 Lbs.
Net Weight:
11.2 Lbs.
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service 8 a.m. - 6 p.m., Eastern, Monday-Friday
1-800-654-3545
Part No. F40BP71920008
Revision: 131101
www.emersonfans.com
Form No. BP7192-8
U.L. Model No.: 52-CL
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
!
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
Additional Safety Instructions for Installation
WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.
WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall
control/switch.
NOTE: This fan is suitable for use with solid-state speed
controls.
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2014” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record
this data above and keep it in a safe place for future use.
2
U.L. Model No.: 52-CL
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Wire Size A.W.G.
Up to 50 ft.
50 - 100 ft.
14
12
One Phillips head screwdriver
One 1/4" blade screwdriver
One stepladder
One wire stripper
Three wire connectors (supplied)
!
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 5). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
Materials
Wiring electrical box and box connectors must be of
type required by local code. The minimum wire would
be a 3-conductor (2-wire with ground) of size shown at
right.
Unpacking Instructions
For your convenience, check-off boxes are provide next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
!
NOTE: Place the parts from the loose parts bag in
a small container to keep them from being lost. If
any parts are missing, contact your local retailer
or catalog outlet for replacement before
proceeding.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
2. Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the upper
foam pad with the lead wires up.
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.
FAN
BLADES
UPPER
FOAM PAD
1.Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
a.
b.
c.
d.
e.
f.
MOUNTING
PLATE
FAN
HOUSING
BLADE FLANGES WITH
CAPTIVE SCREWS
Fan housing
Mounting plate
Fan motor assembly
Five fan blades
Five blade flanges with captive screws
One loose parts bag containing:
1. Sixteen M5 x 6mm Phillips washer
head screws
2. CF804S Only: M5 x 13mm Phillips pan head
screw with lockwasher
CF805S Only: M6 x 14mm Phillips pan head
screw with lockwasher
3. Five M5 x 10mm Phillips pan head screws
with internal tooth washers
4. Four 1/4” hex locknuts
5. One wood pendant
6. One chain coupling
7. Three wire connectors
LOWER
FOAM PAD
FAN
MOTOR
ASSEMBLY
CARTON
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: 52-CL
Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
!
!
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local Codes and the ceiling fan must be properly
grounded as a precaution against possible
electrical shock.
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
!
WARNING
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
How to Hang Your Ceiling Fan
!
NOTE: For better fan performance make sure the
mounting plate is level. Additional washers (not
included) may be needed to insert between the
electrical box and mounting plate (Figure 2).
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 1).
OUTLET BOX
CEILING
AT LEAST
7'
LEVELING WASHERS
(IF REQUIRED)
FLOOR
MOUNTING
PLATE
Figure 1
!
MOUNTING SCREW
(SUPPLIED WITH
OUTLET BOX)
WARNING
Figure 2
The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan Support
of 22.7kg. (50 lbs.) or less”.
!
HOOK
RUBBER WASHER
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
MOUNTING
PLATE
THREADED
STUDS
SUPPLY
WIRE LEADS
FAN
MOTOR
ASSEMBLY
MOTOR
BRACKET
1. Securely attach the mounting plate to the outlet box
(Figure 2) using two screws (supplied with outlet
box). Pull the black, white and ground wires out of
the outlet box through the hole in the mounting
plate and lay them to the side as shown in Figure 3.
Figure 3
4
2. Carefully lift the fan motor assembly and engage
the slot in the motor bracket with the hook on the
mounting plate so that it is securely suspended
(Figure 3). Then connect wiring to your fan
according to section "HOW TO WIRE YOUR
CEILING FAN".
U.L. Model No.: 52-CL
3. Once wiring is completed, lift the motor bracket so
that the four threaded studs on the mounting plate
protrude through the four slot in the motor bracket.
(See Figure 4.)
OUTLET BOX
Securely tighten the four 1/4” hex locknuts
(supplied) onto the threaded studs, then try to
shake the motor bracket to ensure that the
assembly is tight. Proceed to section "HOW TO
PUT YOUR CEILING FAN TOGETHER".
!
MOUNTING
PLATE
1/4" LOCKNUTS
(SUPPLIED) (4)
MOTOR
BRACKET
FAN MOTOR
WARNING
To avoid possible fire or shock, do not pinch wires
between the motor bracket and mounting plate.
SWITCH
HOUSING
Figure 4
How To Wire Your Ceiling Fan
2. Connect the fan motor white wire to the supply
white (neutral) wire using a supplied wire connector
(Figure 5).
3. Connect the fan motor black wire and blue wire to
the supply black (hot) wire using a supplied wire
connector (Figure 5). Your fan is now wired to be
turned on and off from the fan switch. After
connections have been made, turn leads upward
and carefully push leads into the outlet box, with
the white and green leads on one side of the outlet
box and the black and blue leads on the other side
of the outlet box.
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice,
as it must be grounded for safe operation.
1. Connect the green grounding wires from the motor
bracket and the mounting plate to the grounding
conductor of supply (this may be a bare wire or wire
with green colored insulation). Securely connect
wires with wire connectors (supplied).
GREEN GROUND WIRE
!
WARNING
To avoid risk of fire or shock, check to see that all
connections are tight, including ground, and that no
bare wire is visible at the wire connectors, except for
the ground wire. Do not operate fan until blades are
in place. Noise and fan damage could result.
SUPPLY GROUNDING WIRE
GREEN GROUND WIRE
WHITE SUPPLY
BLACK
SUPPLY
(HOT)
4. Connect the wood ball with chain to the 3-speed
switch pull chain.
5. Return to step 3 of section" HOW TO HANG YOUR
CEILING FAN".
MOUNTING
PLATE
MOTOR BRACKET
WHITE FAN WIRE
WIRE
CONNECTORS
BLACK FAN WIRE
BLUE FAN WIRE
Figure 5
NOTE: If you are using an Emerson Light Fixture
with your fan, see the Light Fixture Owner’s
Manual for wiring.
5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: 52-CL
How To Put Your Ceiling Fan Together
1. Align the four holes in the fan housing with the
holes in the mounting plate and install four M5 x
10mm Phillips pan head screws with internal tooth
washers (supplied) (Figure 6).
M5 x 6MM PHILLIPS WASHER
HEAD SCREWS (3)
M5 x 10MM PHILLIPS
PAN HEAD SCREW (4)
BLADE
FLANGE
Figure 7
CAPTIVE SCREW
FAN BLADE
NOTE: Take care not to scratch the fan housing
when installing the blade assemblies.
FAN
HOUSING
Figure 6
BLADE
2. Mount the blade flanges to the fan blades using
three M5 x 6mm Phillips washer head screws per
blade (supplied) (Figure 7). Repeat for four
remaining blades.
!
WARNING
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
Figure 8
BLADE FLANGE
CAPTIVE SCREWS (2 PER FLANGE)
4. You have now completed the assembly of your new
ceiling fan.
3. Attach one blade assembly to the motor using the
captive screw provided for each flange (Figure 8).
Make sure the screws are tightened securely.
Repeat this procedure for the other four blade
assemblies.
Using Your Ceiling Fan
!
Your fan model is equipped with a 4-position,
3-speed pull chain switch. The operating sequence
is as follows:
THREE SPEED:
WARNING
To reduce the risk of fire or electrical shock, do not
use this fan with any solid-state speed control
device.
1st Pull – High
2nd Pull – Medium
3rd Pull – Low
4th Pull – OFF
1. Restore electrical power to the electrical box by
turning the electricity on at the main fuse box or
circuit breaker panel.
2. Check the operation of the fan by gently pulling on
the pull chain switch.
3. All fans are shipped from the factory with the reversing switch positioned to circulate air downward.
If airflow is desired in opposite direction, turn your
fan off and wait for the blades to stop turning, then
slide the reversing switch to opposite position, and
turn fan on again. The fan blades will turn in the
opposite direction and reverse the airflow.
SPEED
CONTROL SWITCH
REVERSING
SWITCH
Figure 9
6
U.L. Model No.: 52-CL
!
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER
BEFORE TROUBLE SHOOTING YOUR FAN.
Trouble Shooting
TROUBLE
PROBABLE CAUSE
SUGGESTED REMEDY
1. Reversing switch in neutral position.
1. Fan will not
start.
2. Fuse or circuit breaker blown.
3. Loose power line connections to the fan,
or loose switch wire connections in switch
housing.
.
1. Blades not attached to fan.
2. Loose screws in motor housing.
2. Fan sounds
noisy.
3. Screws securing fan blade flanges
to motor are loose.
4. Wire connectors inside switch housing
rattling.
5. Screws holding flanges to blades are
loose.
1. Screws securing fan blade flanges to
motor are loose.
2. Fan blade flanges not seated properly.
3. Fan wobbles
or shakes.
3. Mounting plate and/or ceiling outlet
box is not securely fastened.
4. Fan blades out of balance.
1. Check to be sure screws which attach
the fan blade flanges to the motor are tight.
2. Check to be sure the fan blade flanges
seat firmly and uniformly to the surface
of the motor. If flanges are seated
incorrectly, loosen the flange screws
and retighten according to the procedure
in the section on "How to Put Your
Ceiling Fan Together".
3. Tighten the mounting plate screws to
the outlet box, and/or secure outlet box.
4. Interchanging an adjacent (side-byside) blade pair can redistribute the
weight and result in smoother operation.
1. Ceiling Fan Light Kits (see store or catalog).
IMPORTANT CARE INSTRUCTIONS
For Your Ceiling Fan
2. Emerson SW-95 Speed Control (see store or
catalog).
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
!
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
WARNING
!
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
!
1. Attach blades to fan before operating.
2. Check to make sure all screws in motor
housing are snug (not over-tight).
3. Check to make sure the screws which
attach the fan blade flanges to the
motor are tight.
4. Check to make sure wire connectors
in switch housing are not rattling
against each other or against the
interior wall of the switch housing.
5. Tighten securely.
Accessories
Maintenance
!
1. Make sure reversing switch position is
all the way to one side.
2. Check main and branch circuit fuses or
circuit breakers.
3. Check line wire connections to fan and
switch wire connections in the switch
housing.
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.
WARNING
To reduce the risk of fire or electrical shock, do not
use this fan with any solid-state speed control
device.
7
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: 52-CL
Repair Parts
3
2
1
5
4 - Loose Parts Bag Not Shown
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
For repair parts, phone 1-800-654-3545.
8
U.L. Model No.: 52-CL
Repair Parts List
52” Model Numbers
Key
No.
CF805SAB01
CF805SAW01
CF805SBS01
CF805SORB01
CF805SWW01
Switch Housing
Assembly
762577
762577-4
762577-3
762577-9
762577-2
Flange Assembly
(set of 5)
762573-2
762573-4
762573-3
762573-6
762573
Blade Assembly
(set of 5)
762566-1
762566-4
762566-2
762566-5
762566
Loose Parts Bag
Containing:
Blade Hardware
Hanging Hardware
Pull Chain Ball
762567-1
762567
762567-3
762567-1
762567-2
5
Harness, Wiring
762569-2
762569-1
762569-3
762569-2
762569-4
–
Owner’s Manual
BP7192-8
BP7192-8
BP7192-8
BP7192-8
BP7192-8
1
2
3
4
Description
Repair Parts List
42” Model Numbers
Key
No.
CF804SBS01
CF804SORB01
CF804SWW01
Switch Housing
Assembly
762575-5
762575-4
762575
Flange Assembly
(set of 5)
762571-5
762571-4
762571
Blade Assembly
(set of 5)
762564-5
762564-4
762564
Loose Parts Bag
Containing:
Blade Hardware
Hanging Hardware
Pull Chain Ball
762567-4
762567-1
762567-2
5
Harness, Wiring
762568-3
762568-2
762568
–
Owner’s Manual
BP7192-8
BP7192-8
BP7192-8
1
2
3
4
Description
9
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: 52-CL
Notes
10
U.L. Model No.: 52-CL
Emerson Air Comfort Ceiling Fan Limited Warranty
What The Limited Warranty Covers:
This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the original
retail purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components and
accessories of the Emerson Ceiling Fan against all defects in workmanship and materials.
What The Period Of Coverage Is:
This limited warranty will cover the Emerson Ceiling Fan motor for the expected lifetime of your Emerson Ceiling Fan (when operated in accordance with your Owner's
Manual or other instructions provided by Emerson to you with the Emerson Ceiling Fan). All other components and accessories of the Emerson Ceiling Fan are covered
by this limited warranty for a period of one (1) year from its date of original retail purchase. ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS AVAILABLE TO YOU UNDER THE LAWS OF YOUR STATE OR
PROVINCE SHALL COVER THE MOTOR FOR THE EXPECTED LIFETIME OF THE MOTOR (SUBJECT TO PROPER USE), AND FOR ONE YEAR WITH RESPECT TO
COMPONENTS AND ACCESSORIES.
No Other Express or Implied Warranty Applies:
THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES PROVIDED BY EMERSON TO YOU FOR YOUR EMERSON CEILING
FAN, AND ARE IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF LAW OR OTHERWISE,
WHETHER OR NOT THE PURPOSE HAS BEEN DISCLOSED AND WHETHER OR NOT THE EMERSON CEILING FAN HAS BEEN SPECIFICALLY DESIGNED OR
MANUFACTURED FOR YOUR USE OR PURPOSE. EMERSON HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION,
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR COMPONENTS AND ACCESSORIES AS OF THE EXPIRATION OF THE
ONE YEAR WARRANTY PERIOD FOR SUCH COMPONENTS AND ACCESSORIES. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE FOR THE MOTOR PORTION OF THE EMERSON CEILING FAN ARE LIKEWISE DISCLAIMED BY EMERSON AT SUCH TIME THAT THE EXPECTED LIFETIME
OF THE EMERSON CEILING FAN UNDER NORMAL USAGE HAS BEEN REACHED. EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES MAY VARY FROM
STATE TO STATE AND PROVINCE TO PROVINCE SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
What We Will Do To Correct Problems:
If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if during
the expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials or
workmanship, you must contact Emerson during the applicable warranty period. If the defect is covered by warranty, Emerson will repair or replace the defective
motor, component or other accessory at no charge to you. If repair of the motor, component or accessory is not practical or possible within a reasonable time and no
replacement Emerson Ceiling Fan can be provided, Emerson will refund to you the actual purchase price of your Emerson Ceiling Fan. We will ship the repaired or the
replacement Emerson Ceiling Fan to you at no charge, but you are responsible for all costs of removal and reinstallation of your Emerson Ceiling Fan.
How You Can Receive Warranty Service:
You must be the original retail purchaser and have proof of your purchase of the Emerson Ceiling Fan to obtain your remedy under this limited warranty. You can
return your Emerson Ceiling Fan to your place of purchase, or you can call Emerson Customer Service at 1-800-237-6511 to obtain a return authorization and service
identification tag. In order for us to confirm that your Emerson Ceiling Fan is still under warranty, please retain your receipt or other proof of purchase and have that
information readily available when returning your Emerson Ceiling Fan to your place of purchase, or upon calling Emerson Customer Service. If you call Emerson
Customer Service, prior to your call please be prepared to provide all model numbers shown on your Emerson Ceiling Fan. Once we have processed your return
authorization request, we will provide you with a postage paid return label which should be affixed to the Emerson Ceiling Fan package you ship to the address listed at
the end of this limited warranty. The return label will be sent to the mailing address you provide to us by phone.
What Is Not Covered:
This limited warranty does not extend to and expressly excludes:
• The glass globes and light bulbs of your Emerson Ceiling Fan,
• Loss or damage to the motor or any component or accessory caused by normal wear and tear, rather than due to defects in materials or workmanship,
• Loss or damage resulting from conditions beyond our reasonable control, including without limitation, repairs not made at our factory or authorized service center,
use of parts or accessories not provided to you as part of this warranty by our factory or authorized service center, mishandling, unreasonable use, misuse, abuse,
modifications or other damage caused by you or a third party to your Emerson Ceiling Fan while not in our possession,
• Loss or damage resulting from improper installation, or other failure to comply with instructions in your Owner's Manual.
This limited warranty is deemed null and void upon the occurrence of either of the following events:
• You cease to own the Emerson Ceiling Fan product, or
• The Emerson Ceiling Fan is moved from its original point of installation.
This limited warranty is only valid within the 50 United States, the District of Columbia, and Canada. No other written or oral warranties apply, and no employee, agent,
dealer or other person is authorized to give any warranties on behalf of Air Comfort Products or Emerson Electric Co.
Limitation of Liability
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE TO YOU UNDER THIS LIMITED WARRANTY. TO THE EXTENT PERMITTED BY
LAW, IN NO EVENT SHALL EMERSON OR ANY EMERSON AUTHORIZED DEALER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE EMERSON CEILING
FAN OR FOR THE NEGLIGENCE OF EMERSON OR AN EMERSON AUTHORIZED DEALER. EMERSON SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN
PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT,
NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL EMERSON'S OR ANY EMERSON AUTHORIZED AGENT'S LIABILITY TO YOU OR ANY
INDIVIDUAL USING THE EMERSON CEILING FAN EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE EMERSON CEILING FAN. The term "consequential
damages" shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or
equipment.
How State and Provincial Law Relates To The Warranty:
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
11
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: 52-CL
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., Eastern, Monday-Friday
1-800-654-3545
www.emersonfans.com
Retain this manual for future use.
Part No. F40BP71920008
Revision: 131101
Printed in China
11/13
Form No. BP7192-8
U.L. Model No.: 52-CL