156998720en.qxp
1/31/2007
4:22 PM
Page 1
User
manual
Dishwasher
ZDI 100
156998720en.qxp
1/31/2007
4:22 PM
Page 2
Content
Safety information - - - - - - - - - - - - - - - - - - -3
Control panel and functions - - - - - - - - - - - -4
Programme table - - - - - - - - - - - - - - - - - - -6
Before the first use - - - - - - - - - - - - - - - - - -7
Setting the water softener - - - - - - - - - - - - -8
Filling with dishwasher salt - - - - - - - - - - - -9
Filling with rinse aid - - - - - - - - - - - - - - - - -10
Adjusting the dosage of rinse aid - - - - - - -11
Loading cutlery and dishes - - - - - - - - - - - -11
Filling with detergent - - - - - - - - - - - - - - - -13
Unloading the dishwasher - - - - - - - - - - - -14
Cleaning and care- - - - - - - - - - - - - - - - - - 14
Environmental concerns - - - - - - - - - - - - - 15
Something not working - - - - - - - - - - - - - - 16
Technical data- - - - - - - - - - - - - - - - - - - - - 18
Consumption values - - - - - - - - - - - - - - - - 18
Hints for test institutes - - - - - - - - - - - - - - - 19
Installation - - - - - - - - - - - - - - - - - - - - - - - 19
European Guarantee - - - - - - - - - - - - - - - - 22
2
156998720en.qxp
1/31/2007
4:22 PM
Page 3
Safety information
In the interest of your safety and to ensure the correct use, before installing and first using the
appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary
mistakes and accidents. it is important to ensure that all people using the appliance are thoroughly
familiar with its operation and safety features. Save these instructions and make sure that they
remain with the appliance if it is moved or sold, so that everyone using it through its life will be
properly informed on appliance use and safety.
Correct use
●
This dishwasher is only intended for washing
household utensils suitable for machine
washing.
●
Do not put any solvents in the dishwasher.
This could cause an explosion.
●
Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
●
Ensure that the door of the dishwasher is
always closed when it is not being loaded or
unloaded. In this way you will avoid anybody
tripping over the open door and hurting
themselves.
●
Do not sit or stand on the open door.
Child safety
●
This appliance is designed to be operated by
adults. Don’t allow children to use the
dishwasher unsupervised.
●
Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
●
●
Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
Keep all packaging well away from children.
There is risk of suffocation.
●
Do not take any dishes out of the dishwasher
before the end of the dishwashing cycle.
Keep all detergents in a safe place out of
children’s reach.
●
Keep children well away from the dishwasher
when the door is open.
●
●
After use, isolate the appliance from the
power supply and turn off the water supply.
●
This product should be serviced only by an
authorised service engineer, and only
genuine spare parts should be used.
Installation
●
Check your dishwasher for any transport
damage. Never connect a damaged
machine. If your dishwasher is damaged
contact your supplier.
●
All packaging must be removed before use.
●
Any electrical and plumbing work required to
install this appliance must be carried out by
a qualified and competent person.
●
For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
General safety
●
●
Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could
endanger life! Comply with the safety
instructions of the dishwasher detergent
manufacturer.
The water in your dishwasher is not for
drinking. Detergent residues may still be
present in your machine.
3
156998720en.qxp
●
1/31/2007
4:22 PM
Page 4
Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
or if the control panel, work top or plinth area
are damaged such that the inside of the
appliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.
●
All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
WARNING!
For electrical and water connection carefully
follow the instructions given in specific
paragraphs.
Control panel and functions
1. Programme selector dial and On/Off switch
2. Start/cancel button
3. Half load button
4. Indicator lights
5. On/off indicator light
Programme selector dial and
On/Off switch
●
●
4
when in this position, the machine is switched off (On/Off
indicator light off),
when the marker on the dial corresponds with a programme,
the machine is switched on and a programme is selected
(On/off indicator light on).
156998720en.qxp
1/31/2007
4:22 PM
This option must be linked to the selection of a washing programme.
(See “Programme table” chart). When selected, the corresponding light
illuminates. Load dishes in both baskets (lower and upper). When using
this option reduce the dose of detergent that is normally used for a
complete load.
Half load button
Start/Cancel button
Page 5
●
Starting the washing programme:
1. Select a washing programme.
2. Press the Start/Cancel button (On/Off indicator light on).
IMPORTANT!
Once the programme has started, if you want to change the selection made
you must cancel the washing programme in progress.
●
Cancel the washing programme in progress:
1. Press and hold the Start/Cancel button until the corresponding light
turns off.
2. Release the Start/Cancel button.
3. Turn the programme selector dial to the Off position or select a new
washing programme (check that there is detergent in the detergent
dispenser).
Indicator lights
WASH
Illuminates when the washing and rinsing phases are running.
DRY
Illuminates when the drying phase is running.
END
Illuminates when a washing programme has ended.
Switch of the dishwasher by returning the programme selector dial to the
Off position. The On/Off indicator light turns off.
It also has added functions of visual signalling as:
- the setting of the water softener,
- intervention of an alarm due to the malfunction of the machine.
5
156998720en.qxp
1/31/2007
4:22 PM
Page 6
Programme table
Programme
Intensive 65°C
Normal 65°C
Half load
Heavy soil.
Crockery, cutlery,
pots and pans
Prewash - Main wash
2 intermediate rinses Final rinse - Dry
Yes*
Normal soil.
Crockery and cutlery
Final rinse - Dry
Prewash - Main wash
2 intermediate rinses -
Light soil.
Crockery and cutlery
Main washFinal rinse
Yes**
Normal soil.
Crockery and
cutlery
Prewash - Main wash
1 intermediate rinse Final rinse - Dry
Prewash
No
Any.
Partial load (to be completed
later in the day).
This programme does not
require the use of detergent.
Rinse and Hold
* When the Half load button is pressed, the
prewash phase will be automatically
excluded. In this case the detergent dose for
the prewash phase is no longer necessary.
6
Cycle description
Yes*
No
Eco 50°C
Use
** When the Half load button is pressed, the
duration of the washing phase is reduced.
156998720en.qxp
1/31/2007
4:22 PM
Page 7
Before the first use
When using separately special
(dishwasher)salt, rinse aid and
detergent:
- set the water softener
- add special salt
- fill up with rinse aid
When using tablets that integrate
rinse aid and detergent:
there is no need to fill up with rinse aid
- set the water softener
- add special (dishwasher) salt
When using tablets that integrate
rinse aid, detergent, salt function
and other additives:
there is no need to fill up with special salt or
rinse aid.
Check whether these detergents are suitable
for your water hardness. Follow the
manufacturers instructions.
- Set the water hardness to level 1.
IMPORTANT!
If the drying results are not satisfactory we
recommend that you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
If you decide in future to use separated
detergents, we advise that you:
- Fill up the salt and rinse aid container.
- Adjust the water hardness setting to the
highest level and perform 1 normal washing
programme without loading any dishes.
- Adjust the water hardness setting according
to the hardness of the water in your area.
- Adjust the rinse aid dosage
Setting the water softener
The dishwasher is equipped with a water
softener designed to remove minerals and salts
from the water supply, which would have a
detrimental or adverse effect on the operation
of the appliance.
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
IMPORTANT!
The water softener must be set in both ways:
manually and electronically.
7
156998720en.qxp
in °dH1)
1/31/2007
4:22 PM
Water hardness
in mmol/l2)
Page 8
Range
Adjustment of the water hardness setting
manually
electronically
51 - 70
9,0 - 12,5
IV
2
level 10
43 - 50
7,6 - 8,9
IV
2
level 9
37 - 42
6,5 - 7,5
IV
2
level 8
29 - 36
5,1 - 6,4
IV
2
level 7
23 - 28
4,0 - 5,0
IV
2
level 6
19 - 22
3,3 - 3,9
III
2
level 5
15 - 18
2,6 - 3,2
III
1
level 4
11 - 14
1,9 - 2,5
II
1
level 3
4 - 10
<4
0,7 - 1,8
< 0,7
I/II
I
1
1
level 2
level 1
no salt necessary
1) (°dH) German degree, measure of the water hardness.
2) (mmol/l) millimol per litre, international unit for water hardness
Setting the water softener manually (see table)
The water softener is factory set at position 2.
Set switch to position 1
or 2
8
156998720en.qxp
1/31/2007
4:22 PM
Page 9
Setting the water softener electronically (see table)
The water softener is factory set at position 5.
The dishwasher must be switched off
Release the button. The END indicator light will
flash. The number of flashes corresponds to current
level set.
The END indicator light might flash 5 times, for
example. The flashing is repeated every 5 seconds.
Press and hold the start/cancel button and turn the
programme selector dial clockwise till the first
programme.
Keep the button pressed until the programme On/off
indicator light and the start/cancel indicator light
start flashing.
To change the level, press the start/cancel button.
Each time the button is pressed the level increases.
(Level 1 follows level 10).
The END indicator light indicates the new setting.
To memorise the operation, turn the programme
selector dial to position off.
Filling with dishwasher salt
CAUTION!
Use only special salt suitable for dishwashers
Unscrew the cap.
Only before filling with
salt for the first time,
fill the salt container
with water
Using the funnel
provided, pour in the
salt until the container is
full.
9
156998720en.qxp
1/31/2007
Remove any trace of
salt.
4:22 PM
Page 10
Replace the cap tightly
turning it clockwise until
it stops with a click.
IMPORTANT!
Immediately start a complete programme.
IMPORTANT!
The salt container will require topping up
periodically.
The salt cap has a refill indicator window in
the centre in which a green float is clearly
visible when there is salt inside the container
and almost disappears when the salt has
finished.
Filling with rinse aid
Open the lid.
Fill up with rinse aid.
The maximum level for
filling is indicated by
"max".
Clean up any rinse aid
which overflows. Close
the lid and press until it
locks.
CAUTION!
Never fill the rinse aid dispenser with any other
substances (e.g. dishwasher cleaning agent,
liquid detergent). This would damage the
appliance.
Top up the rinse aid
when the indicator (B)
becomes clear.
10
156998720en.qxp
1/31/2007
4:22 PM
Page 11
Adjusting the dosage of rinse aid
Increase the dose if there are drops of water or
lime spots on the dishes after washing.
Open the lid.
Reduce the dose if there are whitish streaks
on the dishes or a bluish film on glassware or
knife blades.
Set the dosage level.
(The dose is factory set
in position 4).
Close the lid and press
until it locks.
Loading cutlery and dishes
●
●
The following items are not suitable for use
in the dishwasher:
- Cutlery with wooden, horn, china or
mother-of-pearl handles
- Plastic items that are not heat resistant
- Older cutlery with glued parts that are not
temperature resistant
- Bonded cutlery items or dishes
- Pewter or copper items
- Lead crystal glass
- Steel items prone to rusting
- Wooden platters
- Items made from synthetic fibres
- Dishes and items of cutlery must not lie
inside one another, or cover each other.
- To avoid damage to glasses, they must not
touch.
- Lay small objects in the cutlery basket.
●
Plastic items and pans with teflon have a
tendency to retain water drops; these
items will not dry as well as porcelain and
steel items.
IMPORTANT!
Before closing the door, ensure that the spray
arms can rotate freely.
When loading the dishwasher, make sure
that you:
- Remove all left over food and debris.
- Soften remnants of burnt food in pans
- Load hollow items such as cups, glasses,
pans, etc. with the opening downwards so
that water cannot collect in the container
or a deep base.
11
156998720en.qxp
1/31/2007
Load cutlery.
For best results we
recommend you to use
the cutlery grid provided
(if the size and
dimensions of the
cutlery allow it).
Load upper basket.
Light items (plastic
bowls etc.) must be
loaded in the upper
basket and arranged so
they do not move.
4:22 PM
Page 12
Place knives and other
items of cutlery with
sharp points or edges
with their handles facing
upwards.
Risk of injury!
For taller items, the cup
racks can be folded
upwards.
Load the lower basket.
Arrange serving dishes and large lids around the
edge of the basket.
If plates are to be loaded in the upper basket:
load them starting from the rear positions; tilting
them slightly forwards and avoiding the front
positions near the door.
Adjusting the height of the upper basket
If washing very large
plates you can load them
in the lower basket after
moving the upper basket
to the higher position.
12
Maximum height of the dishes in:
upper basket
lower basket
With upper basket raised
20 cm
31 cm
With upper basket lowered
24 cm
27 cm
156998720en.qxp
1/31/2007
4:22 PM
Page 13
IMPORTANT!
When the basket is in the higher position you
will not be able to use the cup racks.
Move the front runner
stops (A) of the upper
basket outwards and
slide the basket out.
Refit the basket in
the higher position
and replace the stops
(A) in their original
position.
Filling with detergent
IMPORTANT!
Only use detergents suitable for dishwashers.
Observe the manufacturer’s dosing and storage recommendations.
For programmes with
prewash add an
additional detergent
dose in compartment B.
Open the lid.
Fill in the detergent in
compartment A.
When using detergent
tablets:
place detergent tablets
in compartment A.
Close the lid.
Observe the dosing
levels.
13
156998720en.qxp
1/31/2007
4:22 PM
Page 14
Unloading the dishwasher
IMPORTANT!
Open the dishwasher’s door, leave it ajar and
wait a few minutes before removing the
dishes: hot dishes are sensitive to knocks. In
this way they will be cooler and the drying will
be improved.
Empty the lower basket first and then the
upper one; this will avoid water dripping from
the upper basket onto the dishes in the lower
one.
● Water may appear on the sides and the door
of the dishwasher as the stainless steel will
eventually become cooler than the dishes.
●
Cleaning and Care
Cleaning the filters
IMPORTANT!
NEVER use the dishwasher without filters.
Incorrect repositioning and fitting of the filters will produce poor washing results.
The dishwasher must
be switched off
Clean filters A, B and C
thoroughly under
running water.
Turn the handle about
1
/4 turn anticlockwise
and remove filters B
and C.
Remove filter A from the
base of the washing
compartment.
IMPORTANT!
NEVER try to remove the spray arms.
If residues of soil have clogged the holes in the
upper spray arm, remove them with a
toothpick.
Put the flat filter A back
in the base of the
washing compartment
and ensure that it fits
perfectly under the two
guides D.
14
Replace the filters and
lock by turning the
handle clockwise to the
stop.
156998720en.qxp
1/31/2007
4:22 PM
Page 15
External cleaning
Frost precautions
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc....).
Ensure that the seals around the door, the
detergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
We recommend every 3 months to run a 65°C
wash programme without dishes using
detergent.
Avoid placing the machine in a location where
the temperature is below 0°C. If this is
unavoidable, empty the machine, close the
appliance door, disconnect the water inlet pipe
and empty it.
Prolonged periods of non-operation
If you are not using the machine for any period
of time you are advised to:
1. Unplug the appliance and then turn off the
water.
2. Leave the door ajar to prevent the formation
of any unpleasant smells.
3. Leave the inside of the machine clean.
Moving the machine
If you have to move the machine (moving
house etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge
hoses.
4. Pull the machine out together with the
hoses.
5. Only transport the dishwasher in an upright
position, otherwise salt water may run out.
Environmental concerns
Packaging material
Old appliance
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate
container at the community waste disposal
facilities.
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it shall
be handed over to the applicable collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about recycling
of this product, please contact your local city
office, your household waste disposal service
or the shop where you purchased the product.
WARNING!
When a unit is no longer being used:
- Pull the plug out of the socket.
- Cut off the cable and plug and dispose of
them.
- Dispose of the door catch.
This prevents children from trapping
themselves inside and endangering their
lives.
15
156998720en.qxp
1/31/2007
4:22 PM
Page 16
Something not working
IMPORTANT!
The dishwasher will not start or stops during operation.
Certain problems are due to the lack of simple maintenance or oversights, which can be solved
with the help of the indications described in the chart, without calling out an engineer.
Switch off the dishwasher, open the door and carry out the following suggested corrective actions.
Fault code / malfunction
The dishwasher does not fill with
water.
- continuous flashing of the
start/cancel indicator light
- 1 flash of the "end of
programme" indicator light
The dishwasher will not drain.
- continuous flashing of the
start/cancel indicator light
- 2 flashes of the "end of
programme" indicator light
- continuous flashing of the
start/cancel indicator light
Possible cause
The water tap is blocked or furred
with limescale.
The water tap is turned off.
The filter (where present) in the .
threaded hose fitting at the water
inlet valve is blocked.
The water inlet hose has not been
correctly laid or it is bent or
squashed.
Turn the water tap on.
Clean the filter in the.
threaded hose fitting.
Check the water inlet hose
connection.
The sink spigot is blocked.
Clean out the sink spigot.
The water drain hose has not been
correctly laid or it is bent or
squashed.
Check the water drain hose
connection.
Anti-flood device has activated.
Close the water tap and
contact your local Service
Force Centre.
The dishwasher door has not been
properly closed.
Close the door
The main plug is not plugged in.
Insert the mains plug
- 3 flashes of the "end of
programme" indicator light
The programme does not start.
Solution
Clean the water tap.
The fuse has blown in the household Replace the fuse.
fuse box.
Delay start has been selected.
If dishes are to be washed
immediately, cancel the delay
start.
Once these checks have been carried out; close the door, switch on the dishwasher and press the
start/cancel button. The programme will continue from the point at which it was interrupted. If the
malfunction or fault code reappears contact the Service Force Centre.
For other combinations of fault codes not described in the above chart, please contact your
Service Force Centre.
16
156998720en.qxp
1/31/2007
4:22 PM
Page 17
The wash results are not satisfactory
The dishes are not clean
The wrong washing programme has been selected.
The dishes were arranged in such a way as to stop water reaching all parts
of the surface. The baskets must not be overloaded.
● The spray arm do not rotate freely due to wrong arrangement of the load.
● The filters in the base of the washing compartment are dirty or incorrectly
positioned.
● Too little or no detergent has been used.
● Where there are limescales deposits on the dishes; the salt container is
empty or the wrong level of the water softener has been set.
● The drain hose connection is not correct.
● The salt container cap is not properly closed.
●
●
The dishes are wet and
dull
●
●
Rinse aid was not used.
The rinse aid dispenser is empty.
There are streaks, milky
spots or a bluish coating
on glasses and dishes
●
Decrease rinse aid dosing.
Water drops have dried
onto glasses and dishes
●
Increase rinse aid dosing.
The detergent may be the cause, Contact the detergent manufacturer’s
consumer care line.
●
If after all these checks, the problem persists,
contact your local Service Force Centre,
quoting the model (Mod.), product number
(PNC) and serial number (S.N.).
This information can be found on the rating
plate located on the side of the dishwasher
door (see picture).
So that you always
have these numbers
at hand, we
recommend you to
make a note of them
here:
Mod. : . . . . . . . . . . . .
PNC : . . . . . . . . . . . .
S.N. :. . . . . . . . . . . . .
17
156998720en.qxp
1/31/2007
4:22 PM
Page 18
Technical data
Dimensions
Width
Height
Depth.
59,6 cm
81,8 - 87,8 cm
57,5 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate on
the inner edge of the dishwasher’s door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Capacity
12 place settings
Max. weight
38 Kg
Noise level
53 dB (A)
Consumption values
The consumption values are intended as a
guide and depends on the pressure and the
temperature of the water and also by the
variations of the power supply and the amount
of dishes.
Programme
Programme duration
(minutes)
Energy
(kWh)
Water
(litres)
INTENSIVE 65°C
120 - 130
1,8 - 2,0
22 - 25
NORMAL 65°C
100 - 110
1,4 - 1,6
19 - 21
30
0,9
9
140
1,05
16
12
< 0,1
5
65°C A 30’
BIO 50°C
(Test programme for
Test Institutes)
RINSE & HOLD
18
156998720en.qxp
1/31/2007
4:22 PM
Page 19
Hints for test institutes
Testing in accordance with EN 60704 must be
carried out with appliance fully loaded and
using the test programme (see "Consumption
values").
Test in accordance with EN 50242 must be
carried out when the salt container and rinse
aid dispenser have been filled with salt and
rinse aid respectively and using the test
programme (see "Consumption values").
Full load:
12 standard place settings
Amount of detergent required:
5 g + 25 g (Type B)
Rinse aid setting:
position 4 (Type III)
Upper basket
Cup racks:
position A
Cutlery basket
Lower basket
Installation
WARNING!
Any electrical and/or plumbing work required to
install this appliance should be carried out by a
qualified electrician and/or plumber or
competent person.
Water connection
WARNING!
The dishwasher must not be connected to
open water appliances or instantaneous water
heaters. This dishwasher may be fed with cold
water.
WARNING!
Only use, for connection to the water mains,
new hose-set; old hose-set must not be
reused.
19
156998720en.qxp
1/31/2007
4:22 PM
Page 20
CAUTION!
If the machine is connected to new pipes or pipes which have not been used for a long time, you
should run the water for a few minutes before connecting the inlet hose.
Water inlet hose with safety valve
Drain hose
Connect the inlet hose to a water tap with an
external thread of 3/4”.
After connecting the double-walled water inlet hose,
the safety valve is next to the tap.
If the water inlet hose leaks, the safety valve cuts off
the water supply.
- Connect drain hose to the sink. Secure it with the
supplied hose clamp.
- Required height: 30 to 100 cm above bottom of
the dishwasher.
- If you use a drain hose extension the total length
should not be longer than 4 metres. Likewise the
internal diameter of the couplings used for
connections to the waste outlet must be no
smaller than the diameter of the hose provided.
WARNING!
The electrical cable for the safety valve is in the
double-walled water inlet hose and is live.
Therefore do not immerse the water inlet hose or the
safety valve in water.
Take care when installing the water inlet hose.
Place the water inlet hose in such a way that it is
always lower than the bottom edge of the safety
valve.
If the water inlet hose or the safety valve is
danaged, remove the mains plug immediately.
ATTENTION!
Ensure that the hoses
are not kinked, crushed
or entangled.
A water inlet hose with safety valve MUST only be
replaced by your local Service Force Centre.
Electrical connection
WARNING!
● Safety standards require the appliance to be
earthed. The manufacturer accepts no
liability for failure to observe the above
safety precautions.
●
Prior to using the appliance for the first time,
ensure that the rated voltage and type of
20
supply on the rating plate match that of the
supply where the appliance is to be installed.
The fuse rating is also to be found on the
rating plate.
●
Always plug the mains plug into a correctly
installed shockproof socket.
156998720en.qxp
1/31/2007
4:22 PM
Page 21
WARNING!
● Multi-way plugs, connectors and extension
cables must not be used. This could
constitute a fire hazard through overheating.
●
If necessary, have the domestic wiring
system socket replaced. In case that the
electrical cable has to be replaced, contact
your local Service Force centre.
●
The plug must be accessible after the
appliance has been installed.
●
Never unplug the appliance by pulling on the
cable. Always pull the plug.
Levelling
Good levelling is essential for correct closure
and sealing of the door.
When the appliance is correctly levelled, the
door will not catch on either side of the cabinet.
If the door does not close correctly, loosen or
tighten the adjustable feet until the machine is
perfectly level. (See enclosed template).
Fitting under a counter
IMPORTANT!
Carefully follow the instructions on the
enclosed template for building in the
dishwasher and fitting the furniture panel.
WARNING!
The dishwasher must be secured against
tilting.
Therefore make sure that the counter it is fixed
under, is suitably secured to a fixed structure
(adjacent kitchen units cabinets, wall).
This dishwasher is designed to be fitted under
a kitchen counter or work surface.
No further openings for the venting of the
dishwasher are required, but only to let the
water fill and drain hose and power supply
cable pass through.
The dishwasher incorporates adjustable feet to
allow the adjustment of the height.
During all operations that involve accessibility
to internal components the dishwasher has to
be unplugged.
Be sure that once the appliance has been
installed, it is easily accessible for the service
engineer in the event that a repair is required.
21
156998720en.qxp
1/31/2007
4:22 PM
Page 22
European Guarantee
This appliance is guaranteed by Electrolux in
each of the countries listed below for the
period specified in the appliance guarantee or
otherwise by law. If you move from one of
these countries to another of the countries
listed below the appliance guarantee will move
with you subject to the following qualifications:
• The appliance guarantee starts from the date
you first purchased the appliance which will
be evidenced by production of a valid
purchase document issued by the seller of
the appliance.
• The appliance guarantee is for the same
period and to the same extent for labour and
parts as exists in your new country of
residence for this particular model or range of
appliances.
22
• The appliance guarantee is personal to the
original purchaser of the appliance and
cannot be transferred to another user.
• The appliance is installed and used in
accordance with instructions issued by
Electrolux and is only used within the home,
i.e. is not used for commercial purposes.
• The appliance is installed in accordance with
all relevant regulations in force within your
new country of residence.
• The provisions of this European Guarantee
do not affect any of the rights granted to you
by law.
156998720en.qxp
1/31/2007
4:22 PM
Page 23
www.electrolux.com
Albania
Belgique/België/Belgien
+35 5 4 261 450
+32 2 363 04 44
Rr. Pjeter Bogdani Nr. 7 Tirane
Bergensesteenweg 719, 1502 Lembeek
Česká republika
Danmark
Deutschland
Eesti
España
+420 2 61 12 61 12
+45 70 11 74 00
+49 180 32 26 622
+37 2 66 50 030
+34 902 11 63 88
France
Great Britain
www.electrolux.fr
+44 8705 929 929
Hellas
Hrvatska
Ireland
Italia
Latvija
Lietuva
Luxembourg
Magyarország
Nederland
Norge
Österreich
Polska
Portugal
+30 23 10 56 19 70
+385 1 63 23 338
+353 1 40 90 753
+39 (0) 434 558500
+37 17 84 59 34
+370 5 27 80 609
+35 2 42 43 13 01
+36 1 252 1773
+31 17 24 68 300
+47 81 5 30 222
+43 18 66 400
+48 22 43 47 300
+35 12 14 40 39 39
Romania
Schweiz/Suisse/Svizzera
Slovenija
+40 21 451 20 30
+41 62 88 99 111
+38 61 24 25 731
Slovensko
+421 2 43 33 43 22
Electrolux Slovakia s.r.o., Electrolux
Domáce spotrebiče SK, Seberíniho 1,
821 03 Bratislava
Suomi
Sverige
+35 8 26 22 33 00
+46 (0)771 76 76 76
Türkiye
+90 21 22 93 10 25
Konepajanranta 4, 28100 Pori
Electrolux Service, S:t Göransgatan 143,
S-105 45 Stockholm
Tarlabaþý caddesi no : 35 Taksim Istanbul
Россия
+7 495 937 7837
Budějovická 3, Praha 4, 140 21
Sjællandsgade 2, 7000 Fredericia
Muggenhofer Str. 135, 90429 Nürnberg
Mustamäe tee 24, 10621 Tallinn
Carretera M-300, Km. 29,900
Alcalá de Henares Madrid
Addington Way, Luton, Bedfordshire
LU4 9QQ
4 Limnou Str., 54627 Thessaloniki
Slavonska avenija 3, 10000 Zagreb
Long Mile Road Dublin 12
C.so Lino Zanussi, 26 - 33080 Porcia (PN)
Kr. Barona iela 130/2, LV-1012, Riga
Verkiu, 09108 Vilnius
Rue de Bitbourg, 7, L-1273 Hamm
H-1142 Budapest XIV, Erzsébet királyné útja 87
Vennootsweg 1, 2404 CG - Alphen aan den Rijn
Risløkkvn. 2, 0508 Oslo
Herziggasse 9, 1230 Wien
ul. Kolejowa 5/7, Warsaw
Quinta da Fonte - Edificio Gonçalves Zarco Q 35 - 2774 - 518 Paço de Arcos
Str. Garii Progresului 2, S4, 040671 RO
Industriestrasse 10, CH-5506 Mägenwil
Electrolux Ljubljana, d.o.o.
Trćaška 132, 1000 Ljubljana
129090 Москва, Олимпийский
проспект, 16, БЦ „Олимпик“
23
156998720en.qxp
1/31/2007
4:22 PM
Page 24
www.electrolux.com
156998 721
31 01 2007
Subject to change without notice