Electrolux EHD80170P User manual

user manual
Induction hob
AU
EHD 80170 P
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety instructions.................................. 3
Description of the Appliance .................. 4
Operating the appliance ......................... 7
Tips on Cooking and Frying ................... 15
Cleaning and Care ................................. 17
What to do if … ..................................... 18
5
Disposal ................................................
Installation Instructions ..........................
Assembly ..............................................
Guarantee/Customer Service ................
Service ..................................................
21
22
24
29
31
Subject to change without notice
The following symbols are used in this user information:
1 Warning! This must be read! Important advice for the safety of persons and information
on avoiding damage to the appliance
3 General information and advice
2 Information on environmental protection
z
Dangerous voltage
electrolux 3
1 Safety instructions
Please comply with these instructions. If you
do not, any damage resulting is not covered
by the warranty.
Correct use
• This appliance is not intended for use by
persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person responsible for their safety"
• Do not leave the appliance unattended
during operation.
• This appliance should be used only for
normal domestic cooking and frying of
food.
• The appliance must not be used as a
work surface or as a storage surface.
• Additions or modifications to the appliance are not permitted.
• Do not place or store flammable liquids,
highly inflammable materials or fusible
objects (e.g. plastic film, plastic, aluminium) on or near the appliance.
Children’s safety
• The cooking zones will become hot
when you cook. Therefore, always keep
small children away from the appliance.
• The appliance is not intended for use by
young children or infirm persons without
supervision.
• Children should be supervised to ensure
they do not play with the appliance.
• To avoid small children and pets unintentionally switching the appliance on,
we recommend activation of the child
safety device.
General safety
•
The appliance may only be installed and
connected by trained, registered service
engineers.
• Built-in appliances may only be used after they have built in to suitable built-in
units and work surfaces that meet
standards.
• This appliance is not intended to be operated by means of an external timer or
separate remote control system.
•
In the event of faults with the appliance
or damage to the glass ceramic (cracks,
scratches or splits), the appliance must
be switched off and disconnected from
the electrical supply, to prevent the possibility of an electric shock.
• Repairs to the appliance must only be
carried out by trained registered service
engineers.
Safety during use
• Remove stickers and film from the glass
ceramic.
• There is the risk of burns from the appliance if used carelessly.
• Cables from electrical appliances must
not touch the hot surface of the appliance or hot cookware.
• Overheated fats and oils can ignite very
quickly. Warning! Fire hazard!
• Switch the cooking zones off after each
use.
• Users with implanted pacemakers
should keep their upper body at least
30 cm from induction cooking zones
that are switched on.
• Risk of burns! Do not place objects
made of metal, such as knives, forks,
spoons and saucepan lids on the cooking surface, as they can get hot.
• After use, switch off the hob by its control, do not rely on the pot detector.
Safety when cleaning
• For cleaning, the appliance must be
switched off and cooled down.
• For safety reasons, the cleaning of the
appliance with steam jet or high-pressure cleaning equipment is not permitted.
How to avoid damage to the appliance
• The glass ceramic can be damaged by
objects falling onto it.
• The edge of the glass ceramic can be
damaged by being knocked by the
cookware.
• Cookware made of cast iron, cast aluminium or with damaged bottoms can
scratch the glass ceramic if pushed
across the surface.
4 electrolux
•
•
Objects that melt and things that boil
over can burn onto the glass ceramic
and should be removed straightaway.
Do not use the cooking zones with empty cookware or without cookware.
•
•
To avoid damaging cookware and glass
ceramics, do not allow saucepans or
frying pans to boil dry.
The ventilation gap of 5mm between the
worktop and front of the unit underneath
it must not be covered.
Description of the Appliance
Cooking surface layout
Induction cooking zone 1800 W
with power function 2500 W
Induction cooking zone 1800 W
with power function 2500 W
Induction cooking zone 2400 W
with power function 3700 W
Induction cooking zone 1400 W
with power function 1800 W
Control panel
electrolux 5
Control panel layout
Child lock
with display
Pan recognition and automatic
switch-off indicator
Cooking zone indicators
Timer function
STOP+GO
with indicator
Power function Timer display
Heat setting indicator
Heat setting selection
On/Off
with indicator
Residual heat indicator
Timer
Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. Functions are controlled by
touching sensor fields and confirmed by displays and acoustic signals.
Touch the sensor fields from above, without
covering other sensor fields.
Sensor field
1-9/
Function
On / Off
To switch the appliance on and off
Lock
Locking/unlocking the control panel
Stop+Go
To switch the Keep Warm setting on/off
Cooking zone Off
To switch off the cooking zone
Heat settings
To set heat settings
Power
Switching the power function on and off
Timer
Timer selection
Increase settings
To increase Timer time
Reduce settings
To reduce Timer time
6 electrolux
Displays
Display
+
number
Description
Residual heat
Cooking zone is still hot
Fault
Malfunction has occurred
Pan detection
Cookware is unsuitable or too small or no
cookware has been placed on the cooking
zone
Automatic switch off
Switch off is active.
Residual heat indicator
1 Warning: Risk of burns from residual
heat. After being switched off, the cooking zones take some time to cool down.
Look at the residual heat indicator
.
Control bar
The heat setting and the power function are
set via the control bar. The heat setting indicator consists of a chain of light elements.
Operational readiness
indicator for cooking zone
Heat setting indicator
Power function indicator
Power function
Cooking zone Off
Heat setting selection
3 If the control bar is touched for longer
than 6 seconds, a signal sounds and the
appliance switches itself off.
The induction cooking zones create the
heat required for cooking directly in the base
of the cookware. The glass ceramic is merely
heated by the residual heat of the cookware.
The cooling fan switches itself on and off
depending upon the temperature of the electronics.
electrolux 7
Operating the appliance
3 Use the induction cooking zones with
suitable cookware.
Switching the appliance on and off
Control panel
Display
To switch on
Touch
for 1 second
lights up. The operational readiness indicators of the individual
cooking zones also
light up.
To switch off
Touch
for 1 second
goes out. The operational readiness indicators of the individual
cooking zones also go
out.
3 After switching on, within approx.
10 seconds a heat setting or a function
must be set, otherwise the appliance
automatically switches itself off.
Setting the heat setting
The control bar is touched where the desired
heat setting is positioned. The heat setting is
shown in the display. Correct to the left or the
right, if necessary.
Do not release before the desired heat setting is reached.
8 electrolux
Locking/unlocking the control panel
The control panel, with the exception of the
“On/Off” sensor field, can be locked at any
time in order to prevent the settings being
changed e.g. by wiping over the panel with a
cloth.
Control panel
Display
To switch on
Touch
lights up
To switch off
Touch
goes out
3 When you switch the appliance off, the
locking function is automatically
switched off.
Turning the STOP+GO function
on and off
The STOP+GO function simultaneously toggles all active cooking zones to keep-warm
mode then back to the heat setting they
were at before.
Control panel
To switch on
To switch off
Touch
Touch
3 STOP+GO does not stop timer func3
tions.
STOP+GO controls the entire control
panel apart from the sensor field .
Display
Keep-warm setting
Previous heat setting (not automatic
warm-up or power function)
electrolux 9
Using the automatic warm-up function
All cooking zones are equipped with an automatic warm-up function. When setting a
heat setting using the automatic warm-up
function, the cooking zone switches to full
power for a certain amount of time and then
automatically switches back to the heat setting set.
Step
Control panel
Display
1.
Select warm-up setting
2.
Select the desired heat setting between 1
and 8
display flashes
The desired heat setting is displayed.
display lights up.
As long as the
display is lit,
the appliance is working at full
power.
After the automatic warm-up is
completed, the
display goes
out.
The length of time that the automatic warm
up function operates depends on the heat
setting selected.
Heat setting
Warm-up time
[min:sec]
1
0:10
2
0:10
3
3:10
4
5:50
5
10:10
6
2:00
7
2:30
8
2:50
9
---
10 electrolux
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Switching on the child safety device
Step
Control panel
Pilot light
1.
Switch on appliance. (Do not set a heat
setting.)
lights up. The operational readiness indicators of the individual
cooking zones light up.
2.
Touch
over
for 4 seconds
lights up
The child safety device is switched on
Switching off the child safety device
Step
Control panel
Pilot light
1.
Switch on appliance. (Do not set a heat
setting.)
above
lights up
2.
Touch
above
goes out
3.
Switch appliance off.
for 4 seconds
The child safety device is switched off.
3The child safety device can only be
switched on and off, if no heat setting is set.
Overriding the child safety device
The child safety device can be switched off
in this way for a single cooking session; it remains activated afterwards.
Step
1.
2.
Control panel
Switch appliance on
Touch
for 4 seconds
Pilot light
over
lights up
over
goes out.
Until the appliance is next switched off, it can used as normal. The child safety device is still
active after switching off.
3 After overriding the child safety device, a
heat setting or a function must be set
within approx. 10 seconds, otherwise
the appliance automatically switches itself off.
electrolux 11
Switching the power function on and off
The power function makes more power
available to the induction cooking zones, e.g.
to bring a large quantity of water to the boil
quickly.
The power function is activated for 10 minutes at most. After that the induction cooking
zone automatically switches back to heat
setting 9.
Control panel
Display
To switch on
Touch
The light elements in the
control bar light up. The
display flashes
To switch off
Select the heat setting
The heat setting selected is
shown in the display. The
display above
will go out.
1-9
3 If the power function has ended, the
cooking zones automatically switch
back to the heat setting set previously.
Power Management
The cooking zones of the cooking surface
have a maximum power.
The maximum power is reached when the
heat setting 9 has been set for all cooking
zones.
Two cooking zones generate a pair (see figure) and therefore, the power management
shares the maximum available power between these cooking zones.
When the power function is selected for one
cooking zone, the power management
makes the additional power for this cooking
zone available by reducing the power of the
corresponding other cooking zone.
Example: the heat setting 9 is selected on
one cooking zone. The power function is
switched on for the corresponding cooking
zone. The power function is carried out but
the heat setting 9 of one of the cooking
zones and the power function for the other
cooking zone of the pair exceed the maximum power for both at the same time. For
this purpose, the power management reduces the power of the cooking zone that
switched on first from 9 to example 5 and the
display of this cooking zone changes between 9 and 5 and then stays at the current
possible maximum 5. (If the display changes
between 9 and 5 or 9 and 3 or another value
depends on the type of appliance and the
size of the cooking zone.).
12 electrolux
Using the timer
Function
Condition
Outcome after the time
has elapsed
Automatic cut-out
a heat setting is set
acoustic signal
00 flashes
Cooking zone switches off
Countdown timer
cooking zones not in use
acoustic signal
00 flashes
3 If just one countdown value is set you
can change it only when the appliance is
switched on.
3 If a heat setting is set on this cooking
zone in addition to a countdown timer,
the cooking zone is switched off after
the time set has elapsed.
3 If a cooking zone is switched off, the
timer function set is also switched off.
Selecting a cooking zone
Step
Control panel
Display
1.
Touch
once
Pilot light of the first cooking zone
flashes
2.
Touch
once
Pilot light of the second cooking
zone flashes
3.
Touch
once
Pilot light of the third cooking
zone flashes
4.
Touch
once
Pilot light of the fourth cooking
zone flashes
3 If other timer functions are set, after a
few seconds the shortest remaining
time of all the timer functions is displayed and the corresponding pilot light
flashes.
electrolux 13
Setting the time
Step
Control panel
Indicator
1.
Select
Pilot light for the cooking zone selected flashes
2.
Touch
cooking zone
or
00 to 99
minutes
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Switching off the timer function
Step
Control panel
Indicator
1.
Select
Pilot light of cooking zone selected flashes faster
Time remaining is displayed
2.
Touch
cooking zone
The time remaining counts backwards to 00.
The pilot light goes out.
The Timer function for the selected cooking zone is switched off.
Changing the time
Step
Control panel
Indicator
1.
Select
Pilot light of the selected cooking zone flashes
faster
Time remaining is displayed
2.
Touch
cooking zone
or
01 to 99
minutes
After a few seconds, the pilot light flashes more slowly.
The time is set.
The time counts down.
Displaying the time remaining for a cooking zone
Step
1.
Control panel field
Select cooking zone
Display
Pilot light of the cooking zone selected flashes
faster
The time remaining is displayed
After a few seconds the pilot light flashes more slowly.
Switching off the acoustic signal
Step
Control panel field
Acoustic signal
1.
Touch
Acoustic signal to acknowledge.
Acoustic signal stops.
14 electrolux
Automatic switch off
Cooking surface
• If after switching on the cooking surface,
a heat setting is not set for a cooking
zone within approx. 10 seconds, the
cooking surface automatically switches
itself off.
• If one or more sensor fields are covered
by objects (a pan, etc.) for longer than
approx. 10 seconds, a signal sounds
and the cooking surface switches off
automatically.
• If all cooking zones are switched off, the
cooking surface automatically switches
itself off after approx. 10 seconds.
Control panel
• When the appliance is switched off, if
one or more of the sensor fields on the
control panel are covered for more that
10 seconds, an acoustic signal sounds.
The acoustic signal switches itself off
automatically when the sensor fields are
no longer covered.
Induction cooking zones
• In the case of overheating (e.g. when a
saucepan boils dry) the cooking zone
automatically switches itself off.
is
displayed. Before being used again, the
cooking zone must be set to 0 and
cooled down.
• If cookware that is not suitable is used,
lights up in the display and after 2
minutes the indicator for the cooking
zone switches itself off.
• If one of the cooking zones is not
switched off after a certain time, or if the
heat setting is not modified, the relevant
cooking zone switches off automatically.
is displayed. Before being used
again, the cooking zone must be set to
.
Heat setting
Switches off after
1-2
6 hours
3-4
5 hours
5
4 hours
6-9
1.5 hours
electrolux 15
Tips on Cooking and Frying
3 Information on acrylamides
According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can
constitute a health risk due to acrylamides. Therefore we recommend cooking at the lowest possible temperatures
and not browning foods too much.
Cookware for induction cooking zones
Cookware material
Cookware material
Cast iron
suitable
+
Steel, enamelled steel
+
Stainless steel
+*
Multi-layer pan bottom
+*
Aluminium, copper, brass
-
Glass, ceramic, porcelain
-
3 * Cookware for induction cooking zones
is labelled as suitable by the manufacturer.
Suitability test
Cookware is suitable for induction cooking,
if …
• ... a little water on an induction cooking
zone set to heat setting 9 is heated very
quickly.
• ... a magnet sticks to the bottom of the
cookware.
Cookware base
The bottom of the cookware should be as
thick and flat as possible.
Pan size
Up to a certain limit, induction cooking zones
adapt themselves to the size of the bottom
of the cookware automatically. However, depending on the cooking zone size, the magnetic part of the bottom of the cookware
must have a minimum diameter.
Diameter of cooking zone
[mm]
Minimum diameter of dish base [mm]
210
180
180
145
145
120
3 The cookware must be placed centrally
on the cooking zone.
16 electrolux
Tips on energy saving
2 Place cookware on the cooking zone
before it is switched on.
2 If possible, always place a lid on the
cookware.
Examples of cooking applications
The information given in the following table is for guidance only.
Heat
setting
Cookingprocess
0
1
1-2
2-3
3-4
4-5
suitable for
Cooking
time
Tips/Hints
Off position
Keeping
food warm
Keeping cooked foods warm
as required
Cover
Melting
Hollandaise sauce,
melting butter, chocolate, gelatine
5-25 mins.
Stir occasionally
Solidifying
Fluffy omelettes, baked eggs
10-40 mins.
Cook with lid on
25-50 mins.
Add at least twice as much
liquid as rice, stir milk dishes
part way through cooking
Steaming vegetables, fish
braising meat
20-45 mins.
With vegetables add only a
little liquid (a few tablespoons)
Steaming potatoes
20-60 mins.
Use only a little liquid, e. g.:
max. ¼ l water for
750 g potatoes
Cooking larger quantities of
food, stews and soups
60-150 mins.
Up to 3 l liquid plus ingredients
Simmering rice and milk-based
Simmering
dishes
on low heat
Heating up ready-cooked meals
Steaming
Braising
Boiling
6-7
Gentle
Frying
Frying escalopes, veal cordon
bleu, cutlets, rissoles, sausages,
liver, roux, eggs, pancakes,
doughnuts
Steady frying
Turn halfway through cooking
7-8
Heavy
Frying
Hash browns, loin steaks,
steaks, Flädle (pancakes for garnishing soup)
5-15 mins.
per pan
Turn halfway through cooking
9
Boiling
Boiling large quantities of water, cooking pasta, searing meat (goulash, pot roast),
Searing
deep frying chips
Deep frying
The power function is suitable for heating large quantities of liquid.
electrolux 17
Cleaning and Care
1 Take care! Risk of burns from residual
heat.
1 Warning! Sharp objects and abrasive
cleaning agents can damage the appliance by scratching the glass surface,
which may result in shattering of glass.
Clean the appliance and remove the
residues with water and washing up liquid after each use. Remove also remnants of cleaning agents!
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth
and a little washing up liquid.
2. Rub the appliance dry using a clean
cloth.
Removing deposits
1. Place a scraper on the glass ceramic
surface at an angle.
2. Remove residues by sliding the blade
over the surface.
3. Wipe the appliance with a damp cloth
and a little washing up liquid.
4. Rub the appliance dry using a clean
cloth.
Remove
Type of dirt
imme- when the appliance has
diately
cooled down
sugar, food containing sugar
yes
---
plastics, tin foil
yes
---
limescale and water rings
---
yes
fat splashes
---
yes
shiny metallic discolouration
---
yes
*Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialized shops
3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel.
3 Scratches or dark stains on the glass
ceramic that cannot be removed do not
however affect the functioning of the appliance.
using
a scraper*
cleaner for glass ceramic
or stainless steel*
18 electrolux
What to do if …
Problem
Possible cause
The appliance cannot be switched More than 10 seconds have
on or is not operating
passed since the appliance was
switched on
The lock is switched on
Remedy
Switch the appliance on again.
Switch off the lock (See the section “Locking/unlocking the control panel”)
The child safety device is switched Deactivate child safety device (See
on
the section “Child safety device”)
Several sensor fields were
touched at the same time
Only touch one sensor field
Automatic switch off has been trig- Remove any objects (pan, cloths,
gered
etc.) that are lying on the control
panel. Switch the appliance on
again
The residual heat indicator is not
displaying anything
Dirty control panel
The sensor fields must be dry and
fat-free.
The cooking zone was only on for
a short time and is therefore not
hot
If the cooking zone is supposed to
be hot, call the Customer Service
Department.
Repeated acoustic signal (6x), ap- One or more sensor fields have
pliance switches off
been covered for longer than 10
seconds
Acoustic signal sounds when appliance is switched off
Uncover sensor field
The control panel is wholly or part- Remove objects.
ly covered by objects.
Acoustic signal sounds and appli- The On/Off sensor field has been
ance switches itself on and then
covered up, e.g. by a cloth
off again; after 5 seconds another
acoustic signal sounds
Do not place any objects on the
control panel
Display is switching between two
heat settings
Power management is reducing
the power of this cooking zone
See the section “Switching the
power function on and off”
Unsuitable cookware
Use suitable cookware
lights up
No cookware on the cooking zone Place cookware on the cooking
zone
lights up
The diameter of the bottom of the
cookware is too small for the
cooking zone
Move onto a smaller cooking zone
Overheating protection for the
cooking zone has been triggered
Switch off the cooking zone.
Switch the cooking zone on again
Automatic switch-off has been
triggered
Switch appliance off. Switch appliance on again
Use suitable cookware
electrolux 19
Problem
and number are displayed
Possible cause
Electronics fault
If you are unable to remedy the problem
by following the above suggestions,
please contact your local Service Force
Centre.
1 Warning! Repairs to the appliance are
only to be carried out by qualified service engineers. Considerable danger to
the user may result from improper repairs.
3 If the appliance has been operated incorrectly, the engineer's visit will be
chargeable, even during the warranty
period.
Remedy
Disconnect the appliance from the
electrical supply for a few minutes
(Take the fuse out of the house’s
wiring system)
If after switching on again,
is
displayed again, call the customer
service department
20 electrolux
Operating noises
Depending on the material and the processing of the base, the following noises may occur when using induction cooking zones.
• Cracking noise (1)
when using cookware made of different
materials (Sandwich construction)
• Whistling (1)
when using an individual cooking zone
or several cooking zones with high powers when the cookware is made of different materials (Sandwich construction)
1
•
Humming (2)
can occur at high power levels
• Clicking (2)
during electric switching processes
• Hissing, buzzing (3)
The device is fitted with a fan for cooling
the electrics. A whiring noise can be
heard when operating the fan which
may deviate depending on the performance and may continue for a while after
the appliance is switched off.
The noises described are normal and do
not refer to any defects.
2
3
electrolux 21
Disposal
2 Packaging material
The packaging materials are environmentally friendly and can be recycled.
The plastic components are identified by
markings, e.g. >PE<, >PS<, etc. Please
dispose of the packaging materials in
the appropriate container at the community waste disposal facilities.
2 Old appliance
W
on the product or on its
The symbol
packaging indicates that this product
may not be treated as household waste.
Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences
for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about
recycling of this product, please contact
your local city office, your household
waste disposal service or the shop
where you purchased the product.
22 electrolux
Installation Instructions
1 Safety instructions
Warning! This must be read!
The laws, ordinances, directives and standards in force in the country of use are to be
followed (safety regulations, proper recycling
in accordance with the regulations, etc.)
Installation may only be carried out by a qualified electrician.
The minimum distances to other appliances
and units are to be observed.
Anti-shock protection must be provided by
the installation, for example drawers may
only be installed with a protective floor directly underneath the appliance.
The cut surfaces of the worktop are to be
protected against moisture using a suitable
sealant.
The sealant seals the appliance to the work
top with no gap.
When building in, protect the underside of
the appliance from steam and moisture, e.g.
from a dishwasher or oven.
Avoid installing the appliance next to doors
and under windows. Otherwise hot cookware may be knocked off the rings when
doors and windows are opened.
z
•
•
•
•
•
•
z
•
•
•
•
•
•
Risk of injury from electrical current.
The electrical mains terminal is live.
Make electrical mains terminal free of
voltage.
Follow connection schematic.
Observe electrical safety rules.
Ensure anti-shock protection by installing correctly.
The appliance must be connected to the
electrical supply by a qualified electrician.
Risk of injury from electrical current.
Loose and inappropriate plug and socket connections can make the terminal
overheat.
Have the clamping connections correctly installed by a qualified electrician.
Use strain relief clamp on cable.
CAUTION: The surface temperature exceeds 95°C. To avoid a hazard, underbench access must be restricted.
Supply cords must have a temperature
rating not less than 105°C.
The ventilation gap requirement of 5mm
underneath the cooktop must be observed.
electrolux 23
Electrical Connection
Before connecting, check that the nominal
voltage of the appliance, that is the voltage
stated on the rating plate, corresponds to
the available supply voltage. Also check the
power rating of the appliance and ensure
that the wire is suitably sized in accordance
with local wiring rules. The rating plate is located on the lower casing of the hob.
The heating element voltage is AC230V~.
The appliance also works perfectly on networks with AC220V~ or AC240V~. Means
for disconnection must be incorporated in
the fixed wiring in accordance with local wiring rules.
The hob is to be connected to the mains using a device that allows the appliance to be
disconnected from the mains at all poles with
a contact opening width of at least 3 mm,
eg. automatic line protecting cut-out,earth
leakage tripsorfuse.
If this appliance’s mains cable is damaged, it
must be replaced by a special cable (type
H05BB-F Tmax 90°C; or higher). The latter is
available from the Customer Care Department.
The connection must be carried out as
shown in the diagram, refer to the sticker on
the back of the hob for wiring connection diagram. The connecting links should be fitted
according to the appropriate connection diagram. Note for single phase connection,
the link (or bridge) will need to be fitted between terminals 1 & 2 (refer to the connection sticker on back of the unit). The earth
lead is connected to terminal E. The earth
lead must be longer than leads carrying electric current.
The cable connections must be made in
accordance with regulations and the
terminal screws tightened securely.
Finally, the connecting cable is to be secured
with the mains cable cleat and the covering
closed by pressing firmly (lock into place).
Before switching on for the first time, any
protective foil or stickers must be removed
from the glass ceramic surface.
1 Once connected to the mains supply
check that all cooking zones are ready
for use by briefly switching each on in
turn at the maximum setting.
A duplicate rating label is supplied with
this unit. For easy identification of this
unit after installation, stick it to a readily
available surface adjacent to the cooktop.
Sticking on the seal
• Clean the worktop around the cut-out
area.
• Stick the single-sided adhesive sealing
tape provided on the underside of the
hob around the outside edge ensuring
that it is not stretched. The two ends of
the tape should join in the middle of one
side. After trimming the tape (allow it to
overlap by 2-3 mm), press the two ends
together.
24 electrolux
Assembly
electrolux 25
26 electrolux
electrolux 27
1 WARNING! Surface temperature of base exceed 95°C, under bench access must be
restricted by use of non-combustible barrier on installation.
28 electrolux
Rating Plate
EHD80170P
55GBDC2AU
ELECTROLUX
230 V
50 Hz
949 593 115
Induktion 7,4 kW
7,4 kW
electrolux 29
Guarantee/Customer Service
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: ELECTROLUX
This document sets out the terms and conditions of product warranties for Electrolux branded appliances. It
is an important document.
Please keep it with your proof of purchase documents in a safe place for future reference should you require
service for your Electrolux appliance.
General Terms and Conditions
1. In this warranty
(a) 'Electrolux' means Electrolux Home Products Pty Ltd ABN 51004 762 341 in respect of Appliances purchased in Australia and Electrolux (NZ) Limited in respect of Appliances purchased in New Zealand;
(b) 'Appliance' means any Electrolux product purchased by you accompanied by this document;
(c) 'Warranty Period' means
i) where you use the Appliance for personal, domestic or household purposes in Australia the period
of 24 months and in New Zealand the period of 24 months;
ii) where you use the Appliance for commercial purposes, in Australia the period of 3 months and in
New Zealand the period of 3 months, (if the period stated is 0 months you are not covered by this
product warranty) following the date of original purchase of the Appliance;
(d) 'you' means the purchaser of the Appliance not having purchased the appliance for re-sale, and 'your'
has a corresponding meaning.
2. This warranty only applies to Appliances purchased and used in Australia or New Zealand and is in addition
to (and does not exclude, restrict, or modify in any way) any non-excludable statutory warranties in Australia or New Zealand.
3. Electrolux warrants that, when dispatched from an Electrolux warehouse, the Appliance is free from defects in materials and workmanship for the Warranty Period.
4. During the Warranty Period Electrolux or its Authorised Service Centre will, at no extra charge if your appliance is readily accessible without special equipment, and subject to these terms and conditions, repair
or replace any parts which it considers to be defective. You agree that any replaced Appliances or parts become the property of Electrolux. This warranty does not apply to light globes, batteries, filters or similar
perishable parts.
5. Parts and Appliances not supplied by Electrolux are not covered by this warranty.
6. Where you are within an Electrolux service area, this warranty covers the cost of transport of the Appliance to and from Authorised Service Centres of Electrolux and travelling costs for representatives of the
Authorised Service Centre to and from your home or business. If you are outside an Electrolux service area,
you will bear these costs. For information about whether you are within an Electrolux service area, please
phone 13 13 49 in Australia,
or 0800 10 66 10 in New Zealand.
7. Proof of purchase is required before you can make a claim under this warranty.
8. You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts
or workmanship. Electrolux is not liable in the following situations (which are not exhaustive):
(a) The Appliance is damaged by
i) accident
ii) misuse or abuse, including failure to properly maintain or service
iii) normal wear and tear
iv) power surges, electrical storm damage or incorrect power supply
v) incomplete or improper installation
vi) incorrect, improper or inappropriate operation
vii) insect or vermin infestation.
30 electrolux
(b) The Appliance is modified without authority from Electrolux in writing.
(c) The Appliance's serial number or warranty seal has been removed or defaced.
(d) The Appliance was serviced or repaired by anyone other than Electrolux or its Authorised Service Centres.
9. This warranty, the contract to which it relates and the relationship between you and Electrolux are governed by the law applicable in the Australian State where the Appliance was purchased or the law applicable in New Zealand if the Appliance was purchased in New Zealand. Where the Appliance was purchased in
New Zealand for business purposes the Consumer Guarantee Act does not apply.
Limitation of Liability
10.To the extent permitted by law:
(a) Electrolux excludes all warranties other than as contained in this document;
(b) Electrolux shall not be liable for any loss or damage whether direct or indirect or consequential arising
from your purchase, use or non-use of the Appliance.
11.Provisions of the Trade Practices Act and State consumer legislation in Australia, and the Consumer
Guarantees Act, the Sale of Goods Act and the Fair Trading Act in New Zealand, imply warranties or conditions, or impose obligations, upon Electrolux which cannot be excluded, restricted or modified. To the extent permitted by law, the liability of Electrolux (if any) arising out of or in relation to the Appliance or
any services supplied by Electrolux shall be limited (where it is fair and reasonable to do so),:
(a) in the case of Appliances, at its option, to the replacement or repair of the Appliances or the supply of
equivalent products or the payment of the cost of replacing the Appliances or having the Appliances
repaired or of acquiring equivalent Appliances. Upon being replaced, parts and Appliances become the
property of Electrolux; or
(b) in the case of services, at its option, to the supply of the services again or the payment of the cost of
having the services re-supplied;
and in the case of Appliances or services supplied in New Zealand, loss or damage whether direct or indirect
or consequential that is reasonably foreseeable.
Privacy
You acknowledge that in the event that you make a warranty claim it will be necessary for Electrolux and its
Authorised Service Centres to exchange information in relation to you to enable Electrolux to meet its obligations under this warranty.
Important Notice
Before Calling a Service Technician please check carefully the operating instructions, service booklet and the
warranty terms and conditions.
electrolux 31
Service
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
–
three digit letter-number combination for
glass ceramic
– Model description
– Product number (PNC)
– Serial number (S No.)
(for numbers see rating plate)
– Type of fault
– Any error messages displayed by the
appliance
So that you have the necessary reference
numbers from your appliance at hand, we
recommend that you write them in here:
Model description:
.....................................
PNC:
.....................................
S No:
.....................................
www.electrolux.com
www.electrolux.com.au
www.electrolux.co.nz
867 202 652-D-060309-04