Sharp SL-550 Owner`s manual

Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com.
Owner’s Manual
Installation and Operation
Models:
SL-550TR-E
SL-750TR-E
SL-950TR-E
SL-550TR-IPI-E
SL-750TR-IPI-E
SL-950TR-IPI-E
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC OT
AR
D
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
A. Congratulations
This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Congratulations on selecting a Heat & Glo gas fireplace, an
elegant and clean alternative to wood burning fireplaces.
The Heat & Glo gas fireplace you have selected is designed
to provide the utmost in safety, reliability, and efficiency.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
Your new Heat & Glo gas fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fireplace products!
Homeowner Reference Information
We recommend that you record the following pertinent
information about your fireplace.
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on fireplace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
Type of Gas
The model information regarding your specific fireplace can be found on the
rating plate usually located in the control area of the fireplace.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz)
Gaz)::
NATURAL GAS
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX · UL307B
Gas and Electric
Information
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Model Number
Serial Number
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 Listing and Code Approvals
A.
B.
C.
D.
E.
F.
G.
H.
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
7
7
7
7
7
7
7
8
User Guide
Appliance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Decorative Fronts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote Controls, Wall Controls and Wall Switches . . . . . 10
Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11
Lighting Instructions (Standing Pilot) . . . . . . . . . . . . . . . . 12
After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 13
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 14
B. Maintenance Tasks-Qualified Service Technician . . . . . . 14
Installer Guide
Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . .
Design and Installation Considerations . . . . . . . . . . . . . .
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . .
Inspect Appliance and Components . . . . . . . . . . . . . . . . .
16
17
17
17
5 Framing and Clearances
A.
B.
C.
D.
Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Flex Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
23
23
23
24
25
8 Vent Clearances and Framing
A.
B.
C.
D.
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .
Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . .
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . .
38
38
39
39
Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . .
Constructing the Appliance Chase . . . . . . . . . . . . . . . . . .
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 42
10 Installing Vent Pipe (DVP and SLP Pipe)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . .
Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . .
Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Install Decorative Ceiling Components (SLP only). . . . . .
Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . .
Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . .
Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . .
Install Decorative Wall Components (SLP only) . . . . . . . .
Heat Shield Requirements for Horizontal Termination . . .
Install Horizontal Termination Cap (DVP and SLP Pipe) .
43
44
44
45
45
46
47
47
48
48
48
49
11 Gas Information
4 Getting Started
A.
B.
C.
D.
A.
B.
C.
D.
E.
F.
9 Appliance Preparation
2 Operating Instructions
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
7 Vent Information and Diagrams
18
19
19
20
6 Termination Locations
A.
B.
C.
D.
Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . .
50
50
50
50
12 Electrical Information
A.
B.
C.
D.
E.
F.
G.
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . .
Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . .
Optional Accessories Requirements . . . . . . . . . . . . . . . .
Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . .
Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Switch Installation for Fan (Optional) . . . . . . . . . . . .
51
51
51
51
53
53
53
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 21
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
3
13 Finishing
A.
B.
C.
D.
E.
Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decorative Fronts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . .
54
56
57
58
59
14 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
I.
Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . .
Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lava Rock, Mineral Wool/Ember Placement . . . . . . . . . .
Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . .
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Trim and/or Surround . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
60
60
60
60
61
63
63
63
15 Troubleshooting
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 64
B. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 66
16 Reference Materials
 A. Appliance/Decorative Front Dimension Diagrams . . . . . . 68
B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 72
C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
 = Contains updated information.
4
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
B. Limited Lifetime Warranty
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
X
X
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
Ignition Modules
Firepots and burnpots
X
5 years
Components Covered
Electric Venting
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645G 2/15
Page 1 of 2
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
5
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
•
•
•
•
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
This warranty is only valid while the HHT appliance remains at the site of original installation.
This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
•
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645G 2/15
6
Page 2 of 2
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
1
Listing and Code Approvals
A. Appliance Certification
C. BTU Specifications
MODELS: SL-550TR-E, SL-750TR-E, SL-950TR-E
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Heater
STANDARD: ANSI Z21.88-2014 • CSA 2.33-2014
This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Tempered Glass Specifications
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered
glass has been tested and certified to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certification Council SGCC# 1595 and 1597. Architectural Testing, Inc. Reports 02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
(0-2000 FT)
21,000
15,000
#44
(0-2000 FT)
20,600
14,600
#55
(0-2000 FT)
24,300
16,900
#42
(0-2000 FT)
23,400
17,600
#54
(0-2000 FT)
30,400
20,900
#37
(0-2000 FT)
30,800
23,000
#52
Models
(U.S. or Canada)
SL-550TR-E (NG)
SL-550TR-IPI-E (NG)
SL-550TRLP-E (LP)
SL-550TRLP-IPIE (LP)
SL-750TR-E (NG)
SL-750TR-IPI-E (NG)
SL-750TRLP-E (LP)
SL-750TRLP-IPIE (LP)
SL-950TR-E (NG)
SL-950TR-IPI-E (NG)
SL-950TR-E (LP)
SL-950TR-IPI-E (LP)
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Input ratings are certified without a reduction
of input rate for elevations up to 4500 feet (1370 m)
above sea level. Please consult provincial and/or
local authorities having jurisdiction for installations at
elevations above 4500 feet (1370 m).
Check with your local gas utility to determine proper
orifice size.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750 ºC shall be considered
non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
7
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
8
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
2
Operating Instructions
User Guide
A. Appliance Safety
• Teach children to NEVER touch the fireplace.
WARNING! DO NOT operate fireplace before reading
and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
• Consider not using the fireplace when children will be
present.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
• Keep children away.
• CAREFULLY SUPERVISE children in same room
as fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Clothing, furniture, draperies, and other flammable
materials must not be placed on or near the
appliance.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed for the protection of children and other
at-risk individuals. DO NOT operate the appliance with
the barrier removed. If the barrier becomes damaged,
the barrier shall be replaced with the manufacturer’s
barrier for this appliance.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fireplace for an extended period of time (summer months,
vacations, trips, etc):
• Remove batteries from remote controls.
• Turn off wall controls.
• Unplug 3 volt adapter plug and remove batteries on IPI
models.
• Turn off gas controls valve on standing pilot models.
When lighting the pilot light on fireplaces with a standing
pilot, remove the fixed glass assembly so you can detect presence of residual gas build-up. See Standing Pilot
Lighting instructions and Maintenance Tasks.
B. Your Fireplace
WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.E.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 14.G.
Young children should be carefully supervised when they
are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental
contact burns.
• A physical barrier is recommended if there are at risk
individuals in the house.
• To restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young children
and other at risk individuals out of the room and away
from hot surfaces.
• Install a switch lock or a wall/remote control with child
protection lockout feature.
MANTEL
FAN KIT
SECTION 2.C
HEARTH
CLEAR SPACE
SECTION 2.D.
• Keep remote controls out of reach of children.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
Figure 2.1 General Operating Parts
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
9
C. Fan Kit (optional)
F. Fixed Glass Assembly
If desired, a fan kit may be added. Contact your dealer to
order the correct fan kit.
See Section 14.G.
D. Clear Space
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
G. Remote Controls, Wall Controls and Wall
Switches
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
H. Before Lighting Fireplace
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Review proper placement of logs, ember material and/or
other decorative materials.
• Check the wiring.
3F
T.
IN CLE
FR AR
ON S
T O PAC
FF E
IR
EP
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
LA
CE
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.
Figure 2.2 Clear Space
E. Decorative Fronts
WARNING! Risk of Fire! Install ONLY decorative fronts
approved by Hearth & Home Technologies. Unapproved
decorative fronts may cause fireplace to overheat.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
Determine if this fireplace has a standing pilot or an
Intellifire ignition system. Ask your dealer or open control
access panel, look at gas valve assembly.
• A standing pilot ignition will have a red or black ignitor
button (refer to Figure 2.3).
• An Intellifire ignition system will not have a button.
RED OR
BLACK
BUTTON
For more information refer to the instructions supplied with
your decorative front.
Figure 2.3 Ignitor Button
10
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
I. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an intermittent pilot ignition (IPI) device which
automatically lights the burner. DO NOT try to light the burner by hand.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell
next to the floor because some gas is heavier than air and will settle on the floor.
• If you cannot reach your gas supplier, call the fire department.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any phone in your building.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If
the knob will not push in or turn by hand, DO NOT try to repair it, call a qualified
service technician. Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any part has been under water. Immediately call
a qualified service technician to inspect the appliance and to replace any part of
the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS (IPI)
1.
This appliance is equipped with an ignition device which
automatically lights the burner. DO NOT try to light the burner by hand.
GAS
VALVE
2.
Wait five (5) minutes to clear out any gas. Then smell for gas, including near the
floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the
top of this label. If you do not smell gas, go to next step.
3.
To light the burner:
Equipped with wall switch: Turn ON/OFF switch to ON.
Equipped with remote or wall control: Press ON or FLAME button.
Equipped with thermostat: Set temperature to desired setting.
4.
If the appliance does not light after three tries, call your service technician or gas
supplier.
TO TURN OFF GAS TO APPLIANCE
1.
Equipped with wall switch: Turn ON/OFF switch to OFF.
Equipped with remote or wall control: Press OFF button.
Equipped with thermostat: Set temperature to lowest setting.
2.
Service technician should turn off electric power to the control when performing
service.
DANGER
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.
WARNING:
CAUTION:
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to the owner’s information manual provided with
this appliance. For assistance or additional information, consult a qualified installer,
service agency or the gas supplier.
DO NOT operate the appliance with fixed glass assembly removed, cracked or
broken. Replacement of the fixed glass assembly should be done by a licensed or
qualified service person.
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.
This appliance needs fresh air for safe operation and must be installed so there are
provisions for adequate combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which
are known to the State of California to cause cancer, birth defects, or other reproductive
harm.
Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline
and other liquids having flammable vapors away.
NOT FOR USE WITH SOLID FUEL
For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.
Also Certified for Installation in a Bedroom or a Bedsitting Room.
This appliance must be installed in accordance with local codes, if any; if none,
follow the National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and
Propane Installation code, CSA B149.1.
Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
593-913i
11
J. Lighting Instructions (Standing Pilot)
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand. When lighting the
pilot, follow these instructions exactly.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell
next to the floor because some gas is heavier than air and will settle on the floor.
• If you cannot reach your gas supplier, call the fire department.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any phone in your building.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If
the knob will not push in or turn by hand, DO NOT try to repair it, call a qualified
service technician. Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any part has been under water. Immediately call
a qualified service technician to inspect the appliance and to replace any part of
the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1
Turn off all electric power to the appliance
6.
Turn knob on gas control counterclockwise to
2.
Push in gas control knob slightly to turn clockwise
to “OFF”.
7.
Push in control knob all the way and hold in. Immediately depress red or
black piezo button. It may require several depressions of the red or black
piezo button until PILOT lights . If PILOT light does not light after 10 seconds, return to step 2. Continue to hold the control knob in for about one
minute after the pilot is lit. Release knob and it will pop back out. Pilot
should remain lit. If it goes out, repeat steps 2 through 5.
8.
Reinstall fixed glass assembly. Reinstall decorative front.
9.
Turn gas control knob counterclockwise to
Note: Knob cannot be turned from “PILOT” to “OFF” unless
knob is pushed in slightly. DO NOT force.
3.
Open the fixed glass assembly. You may need to remove the decorative front.
4.
Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety
Information located at the top of this label.
5.
Find the pilot. The pilot is inside combustion chamber next to the
main burner.
1.
Turn off all electric power to the appliance if service is to provided.
2.
Move switch to “OFF” position.
“PILOT”.
“ON”.
10. Turn on electric power to the appliance.
11. To light burner, turn the wall control or on/off switch to “ON”.
TO TURN OFF GAS TO APPLIANCE
3.
Push in gas control knob slightly and turn clockwise to
DO NOT force.
“OFF”.
DANGER
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance
and shall be installed for the protection of children and other at-risk individuals.
CAUTION:
WARNING:
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.
Hot while in operation. DO NOT touch. Severe burns may result. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to the owner’s information manual provided with
this appliance. For assistance or additional information, consult a qualified installer,
service agency or the gas supplier.
DO NOT operate the appliance with fixed glass assembly removed, cracked or
broken. Replacement of the fixed glass assembly should be done by a licensed or
qualified service person.
This appliance needs fresh air for safe operation and must be installed so there are
provisions for adequate combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which
are known to the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.
NOT FOR USE WITH SOLID FUEL
For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.
Also Certified for Installation in a Bedroom or a Bedsitting Room.
This appliance must be installed in accordance with local codes, if any; if none,
follow the National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and
Propane Installation code, CSA B149.1.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
12
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
464-903i
K. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.G.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fireplace.
NOTICE! Open windows for air circulation during fireplace break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
L. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the appliance.
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Film on the glass
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn
continually?
In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when
ON/OFF is turned off. In a standing pilot system the pilot will always stay on.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
13
3
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend annual service by a qualified service technician.
A. Maintenance Tasks-Homeowner
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service appointment.
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
Glass Cleaning
Frequency: Seasonally
By: Homeowner
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.
• Remove decorative front from fireplace and set aside
on work surface.
• See Section 14.G for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
Surrounds, Decorative Fronts
Frequency: Annually
By: Homeowner
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
• Inspect for scratches, dents or other damage and repair
as necessary.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
Remote Control
Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote control instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
• Place batteries as needed in remote transmitters and
battery-powered receivers.
• Place remote control out of reach of children.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unintended operation:
• Remove batteries from remote controls.
• Unplug 3 volt adapter plug on IPI models.
Venting
Frequency: Seasonally
By: Homeowner
Tools needed: Protective gloves and safety glasses.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See
Section 6.
• Inspect for corrosion or separation.
• Verify weather stripping, sealing and flashing remains
intact.
• Inspect draft shield to verify it is not damaged or missing.
- Light deposits: Use a soft cloth with soap and water
B. Maintenance Tasks-Qualified Service
Technician
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
The following tasks must be performed by a qualified service technician.
• Carefully set fixed glass assembly in place on fireplace.
Hold glass in place with one hand and secure glass
latches with the other hand.
Gasket Seal and Glass Assembly Inspection
• Reinstall decorative front.
14
Frequency: Annually
By: Qualified Service Technician
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
Logs
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves.
• Inspect for damaged or missing logs. Replace as necessary. Refer to Section 14 for log placement instructions.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
Firebox
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Replace fireplace if firebox has been perforated.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 14 for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 3.1
and 3.2 for proper pilot flame pattern. Clean or replace
orifice spud as necessary.
• Inspect thermocouple/thermopile or IPI flame sensing
rod for soot, corrosion and deterioration. Polish with fine
steel wool or replace as required.
• Verify thermocouple/thermopile millivolt output. Replace
pilot as necessary. (Standing pilot only)
• Verify that there is not a short in flame sense circuit
by checking continuity between pilot hood and flame
sensing rod. Replace pilot as necessary. (IPI only)
Control Compartment and Firebox Top
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
Figure 3.1 IPI Pilot Flame Patterns
Burner Ignition and Operation
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 14 for proper ember placement.
• Verify batteries have been removed from battery back-up
IPI systems to prevent premature battery failure or
leaking.
Figure 3.2 Standing Pilot Flame Patterns
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
15
4
Installer Guide
Getting Started
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual.
HORIZONTAL
TERMINATION CAP
(SECTION 10.L)
Note: Dual venting configurations
ARE NOT allowed. Appliance MUST
be vented EITHER ver tically OR
horizontally.
VERTICAL TERMINATION CAP
(SECTION 10.I)
NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE (SECTION 10.G)
STORM COLLAR
(SECTION 10.H)
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)
VENT PIPE (SECTIONS 7 and 9)
ATTIC INSULATION SHIELD (NOT
SHOWN) MUST BE USED HERE
TO KEEP INSULATION AWAY
FROM VENT PIPE IF ATTIC IS
INSULATED (SECTION 8.D)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)
FRAMING/HEADER
(SECTION 5.B)
FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION 8.C)
OPTIONAL
WALL SWITCH
MANTEL AND
MANTEL LEG
(SECTION 5.D)
SURROUND
HEARTH EXTENSION
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
16
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
Before installing, determine the following:
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping requirements.
• Electrical wiring requirements.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
Installation and service of this appliance should
be performed by qualified personnel. Hearth &
Home Technologies suggests NFI certified or
factory trained professionals, or technicians
supervised by an NFI certified professional.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Framing material
Pliers
Non-corrosive leak check solutionHammer
Phillips screwdriver
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
Reciprocating saw
Manometer
Flat blade screwdriver
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure
rating)
One 1/4 in. female connection (for optional fan).
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
17
5
Framing and Clearances
A. Selecting Appliance Location
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
A
N
E
L
F
D
F
A
A
C
C
K
H
B
J
G
I
G
J
M
Models
SL-550TR-IPI-E
SL-550TR-E
SL-750TR-IPI-E
SL-750TR-E
SL-950TR-IPI-E
SL-950TR-E
A
B
C
42
37
59-1/2
mm
1067
940
1511
in.
45-1/2
42
64-3/8
mm
1156
1067
1635
in.
50-1/2
49
71-1/2
mm
1283
1245
1816
in.
D
See Section
5.D for Alcove
Installation
E
Min.
F
Min.
G
H
I
J
K
L
M
N
1
1/2
44
62-1/4
16-1/4
48-1/2
68-3/4
15-1/16
7-1/2
7-1/8
25
13
1118
1581
413
1232
1746
383
191
181
1
1/2
45-1/2
64-3/8
16-1/4
48-1/2
68-3/4
16-5/8
7-1/2
9
25
13
1156
1635
413
1232
1746
422
191
229
1
1/2
50-1/2
71-1/2
16-1/4
50-1/2
71-1/2
19-1/2
9-1/4
11-5/8
25
13
1283
1816
413
1283
1816
495
235
295
Figure 5.1 Appliance Locations
18
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
B. Constructing the Appliance Chase
firestops should be caulked with caulk with a minimum of
300ºF continuous exposure rating to seal gaps. Gas line
holes and other openings should be caulked with caulk with
a minimum of 300ºF continuous exposure rating or stuffed
with unfaced insulation. If the appliance is being installed
on a cement surface, a layer of plywood may be placed
underneath to prevent conducting cold up into the room.
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
C. Clearances
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
• Failure to maintain airspace may cause overheating and
a fire.
To further prevent drafts, the wall shield and ceiling
A
MEASURE FROM TOP OF
UNIT OPENING OR FROM
TOP OF HOOD
E
F
H
B
C
G
J
D
I
* MINIMUM FRAMING DIMENSIONS
A
B
DVP Pipe SLP Pipe
Models
SL-550TR-E
SL-750TR-E
SL-950TR-E
in.
mm
in.
mm
in.
mm
Rough
Opening
(Width)
Rough
Opening
(Width)
10
254
10
254
10
254
8-5/8
219
8-5/8
219
8-5/8
219
C
D
E
F
G
H
I
J
**DVP Pipe SLP Pipe
Rough
Opening
(Height)
34-3/4
883
38-1/4
971
42 1/4
1073
Rough
Opening
(Depth)
Rough
Opening
(Depth)
16-1/4
413
16-1/4
413
16-1/4
413
16-1/4
413
16-1/4
413
16-1/4
413
Rough
Clearance Combustible Combustible Behind
Sides of
Front of
Opening
to Ceiling
Floor
Flooring
Appliance Appliance Appliance
(Width)
37
940
42
1067
49
1245
32
813
32
813
32
813
0
0
0
0
0
0
0
0
0
0
0
0
1/2
13
1/2
13
1/2
13
1/2
13
1/2
13
1/2
13
36
915
36
915
36
914
* Adjust framing dimensions for interior sheathing (such as sheetrock)
C** Add 12 inches for rear venting with one 90° elbow.
Figure 5.2 Clearances to Combustibles
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
19
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than
the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).
1/2 IN.
MINIMUM
CEILING
All measurements are in inches.
2-7/8 IN.
MINIMUM
3 FT. MAXIMUM
12
10
9
5
3
6
7
11
Note: Clearance from opening
to perpendicular wall.
8
32
4
4
5
6
7
8
10
9
11
12
Figure 5.5 Mantel Leg (Acceptable on both sides of opening.)
13
TOP OF HOOD OR FIREPLACE OPENING
3 IN.
MINIMUM
5-3/8 IN.
MINIMUM
Figure 5.3 Clearances to Mantels or other Combustibles
above Appliance
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
Figure 5.6 Wall Projection (Acceptable on one side of opening.)
1/2 in. SHEETROCK
OR COMBUSTIBLE
MATERIAL
3-1/2 in.
1/2 in.
SHEETROCK
3-1/2 in.
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
1/2 in.
1/2 in.
NON-COMBUSTIBLE ZONE
Figure 5.4 Non-Combustible Zone
Models: SL-550TR-E, SL-750TR-E
SL-550TR-IPI-E, SL-750TR-IPI-E
20
NON-COMBUSTIBLE ZONE
Figure 5.7 Non-Combustible Zone
Models: SL-950TR-E, SL-950TR-IPI-E
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
6
Termination Locations
A. Vent Termination Minimum Clearances
WARNING
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
Fire Risk.
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
Gas, Wood or Fuel Oil
Termination Cap
B
A*
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Gas
Termination
Cap **
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
*
**
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
Figure 6.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5*
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
21
O
N
P
R
F
C
V
Q
B
J
H or i
B
V
D
V
B
V
V
H
V
X
G
M
V
A
V
E
H
V
V
V
L
A
V
V = VENT TERMINAL
X = AIR SUPPLY INLET
K
B
C
V
V
= 12 inches.................clearances above grade, veranda,
porch, deck or balcony
= 12 inches.................clearance to window or door that may
be opened, or to permanently closed
window
= 18 inches.................clearance below unventilated soffit
18 inches.................clearance below ventilated soffit
30 inches .................clearance below vinyl soffits and
electrical service
D
= 6 inches...................clearance to outside corner
E
= 6 inches...................clearance to inside corner
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
N
O
= 6 inches.................clearance from sides of electrical
service
L
= 12 inches................clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.
M
= 18 inches ....................clearance under veranda, porch, deck,
balcony or overhang
42 inches ................vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the floor.
Figure 6.3 Minimum Clearances for Termination
= 18 inches ......... non-vinyl soffit and overhang
42 inches ......... vinyl soffit and overhang
P
= 3 ft. (Canada) ..........not to be installed above a gas meter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
G = 3 ft ...........................clearance to gas service regulator
vent outlet
H
= 9 inches (U.S.A)
12 inches (Canada).clearance to non-mechanical (unpowered) air supply inlet, combustion air
inlet or direct-vent termination
i
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap
must be a minimum of 3 feet below termination.
J
= 7 ft. ......................... On public property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
K
= 6 inches ........... non-vinyl sidewalls
12 inches ......... vinyl sidewalls
F
22
K
C
= AREA WHERE TERMINAL IS NOT PERMITTED
A
Electrical
Service
= 8 ft.
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUAL
2 caps
6 feet
1 x Q ACTUAL
3 caps
9 feet
2/3 x Q ACTUAL
4 caps
12 feet
1/2 x Q ACTUAL
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
Measure vertical clearances from this surface.
CLEARANCE = 6 IN.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffic areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.
•
Local codes or regulations may require different
clearances.
•
Vent system termination is NOT permitted in screened
porches.
•
Vent system termination is permitted in porch areas with
two or more sides open.
•
Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
Vinyl protection kits are suggested for use with vinyl siding.
•
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
7
Vent Information and Diagrams
A. Approved Pipe
DO NOT mix pipe, fittings or joining methods from different manufacturers.
Vertical
12
in
.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
8-1/2 in.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
B. Vent Table Key
Horizontal
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
8-1/2 in.
This appliance is approved for use with Hearth & Home
Technologies DVP or SLP venting systems. Refer to Section 16B for vent component information.
Figure 7.1
Description
V1
First section (closest to appliance) of vertical length
V2
Second section of vertical length
H1
First section (closest to appliance) of horizontal length
H2
Subsequent sections of horizontal length
C. Use of Elbows
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).
D. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
6.3).
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
• Horizontal termination cap should have a 1/4 inch
downward slant to allow any moisture in cap to be
released.
Pipe
Effective
Height/Length
Effective Length
Inches
Millimeters
DVP4
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
Figure 7.2 DVP Pipe Effective Length
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
23
E. Use of Flex Vent
The flex vent must be supported with
the spacing between support intervals
not exceeding 4 feet, with no more
than 1/2 inch sag between supports.
A support is required at each change
in venting direction, and in any location
where it is necessary to maintain the
necessary clearance to combustibles.
A simple “up and out” installation (Figure 5.3) requires only enough support
to maintain the necessary clearance
to combustibles. However, the vent attachment point and the firestop location are considered to be supports.
3 in.
CLEARANCE
FLEX VENT
1 in.
CLEARANCE
Figure 7.3
24
TERMINATION CAP
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
F. Vent Diagrams
Top Vent - Horizontal Termination
Venting with one 90º elbow
V1 Minimum
90 Elbow *
H1 Maximum
SL-550TR-E
SL-750TR-E
SL-950TR-E
2 ft.
610 mm
2 ft.
610 mm
1 ft.
305 mm
152 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
1-1/2 ft.* 457 mm
3 ft.
914 mm
3 ft.
914 mm
3 ft.
914 mm
2-1/2 ft.* 762 mm
5 ft.
1.5 m
5 ft.
1.5 m
5 ft.
1.5 m
3-1/2 ft.
1.1 m
7 ft.
2.1 m
7 ft.
2.1 m
7 ft.
2.1 m
4-1/2 ft.
1.4 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
1/2 ft.*
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
H MAX. =14 ft. (4.3 m)
V + H MAX. = 40 ft. (12.2 m)
* See warning below
V1
H1
WARNING *
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZC-SS
termination caps on top vented fireplaces, a one
foot minimum vertical vent section is required before
installing first elbow.
• When using DVP-TB1 termination cap on top vented fireplaces,
a three foot minimum vertical vent section is required before
installing first elbow.
Figure 7.4
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
25
Top Vent - Horizontal Termination
Venting with two 90º elbows
V Minimum
90 Elbow *
H1 + H2 Maximum
SL-550TR-E
SL-750TR-E
1/2 ft. 152 mm 1/2 ft. 152 mm
SL-950TR-E
0 ft.
0 mm
1/2 ft.*
152 mm
1 ft.
305 mm
1 ft.
305 mm
1 ft.
305 mm
1-1/2 ft.*
457 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
2-1/2 ft.*
762 mm
4 ft.
1.2 m
4 ft.
1.2 m
4 ft.
1.2 m
3-1/2 ft.
1.1 m
6 ft.
1.8 m
6 ft.
1.8 m
6 ft.
1.8 m
4-1/2 ft.
1.4 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
H + H1 MAX. =14 ft. (4.3 m)
V + H + H1 MAX. = 40 ft. (12.2 m)
* See warning below
V1
H2
H1
INSTALLED
HORIZONTALLY
WARNING *
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZC-SS
termination caps on top vented fireplaces, a one
foot minimum vertical vent section is required before
installing first elbow.
• When using DVP-TB1 termination cap on top vented fireplaces,
a three foot minimum vertical vent section is required before
installing first elbow.
Figure 7.5
26
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Top Vent - Horizontal Termination
Venting with three 90º elbows
V1 Minimum
90 Elbow **
H1 + H2 Maximum
SL-550TR-E
SL-750TR-E
SL-950TR-E
V2
V1 + V2 Min.
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
*
*
6 ft.
1.8 m
6 ft.
1.8 m
6 ft.
1.8 m
*
*
1-1/2 ft.** 457 mm 10 ft.
3.0 m
10 ft.
3.0 m
10 ft.
3.0 m
*
*
2-1/2 ft.** 762 mm 12 ft.
3.7 m
12 ft.
3.7 m
12 ft.
3.7 m
*
*
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
*
*
1/2 ft.**
3-1/2 ft.
152 mm
1.1 m
14 ft.
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
H1 + H2 MAX. =14 ft. (4.6 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
*No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)
** See warning below
H2
V2
H1
V1
WARNING **
Fire Risk.
• When using SLP-HRC-SS and SLP-HRC-ZCSS termination caps on top vented fireplaces,
a one foot minimum vertical vent section is
required before installing first elbow.
• When using DVP-TB1 termination cap on top vented
fireplaces, a three foot minimum vertical vent section is
required before installing first elbow.
Figure 7.6
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
27
Top Vent - Vertical Termination
No Elbows
V1 = 60 ft. Max. (18.3 m)
Note: If installing a vertical vent/termination off the top of
the appliance, the optional vertical termination baffle may
be needed.
Exhaust restrictor Instructions
1. Install the exhaust restrictor over the center of the exhaust outlet in the firebox (see Figure 7.8).
2. Center the exhaust restrictor in the open end of the
exhaust outlet and secure through the slots on the exhaust restrictor with the 2-1/4 in. self-tapping screws
provided in the appliance manual bag.
To access the exhaust
openings, remove the exhaust baffle. To remove
exhaust baffle, remove
the two wing nuts.
Note: Use SLP Series
components only.
Top Vent Application
Exhaust restrictor
V1
Rear Vent Application
Exhaust restrictor
Note: Be sure to reinstall the exhaust baffle
after exhaust restrictor
installation.
Figure 7.7
Exhaust restrictors are recommended for these vertically
terminated products which have excessive draft. Exhaust
restrictors will compensate for high draft, and restore visual flame height. If the vent configuration has a total
vertical of 15-60 feet, an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance
manual bag.
28
Figure 7.8
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
EXHAUST BAFFLE
Top Vent - Vertical Termination
Venting with two 90º elbows
V1 MIN.
90 Elbow
SL-550TR-E
SL-750TR-E
SL-950TR-E
H MAX.
H MAX.
H MAX.
1-1/2 ft.
457 mm
1-1/2 ft.
457 mm
1 ft.
305 mm
V2
V1 + V2 MIN.
*
*
1/2 ft.
152 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
*
*
1-1/2 ft.
457 mm
3 ft.
914 mm
3 ft.
914 mm
3 ft.
914 mm
*
*
2-1/2 ft.
762 mm
5 ft.
1.5 m
5 ft.
1.5 m
5 ft.
1.5 m
*
*
3-1/2 ft.
1.1 m
7 ft.
2.1 m
7 ft.
2.1 m
7 ft.
2.1 m
*
*
4-1/2 ft.
1.4 m
15 ft.
4.6 m
15 ft.
4.6 m
15 ft.
4.6 m
*
*
H MAX. =15 ft. (4.6 m)
V1 + V2 + H MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
V2
H1
V1
Figure 7.9
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
29
Top Vent - Vertical Termination
Venting with three 90º elbows
V1 MIN.
90 Elbow
SL-550TR-E
SL-750TR-E
SL-950TR-E
H MAX.
H MAX.
H MAX.
V2
V1 + V2 MIN.
1/2 ft.
152 mm
1/2 ft.
152 mm
0 ft.
0 mm
*
*
152 mm
1 ft.
305 mm
1 ft.
305 mm
1 ft.
305 mm
*
*
1-1/2 ft. 457 mm
2 ft.
610 mm
2 ft.
610 mm
2 ft.
610 mm
*
*
2-1/2 ft. 762 mm
4 ft.
1.2 m
4 ft.
1.2 m
4 ft.
1.2 m
*
*
3-1/2 ft.
1.1 m
6 ft.
1.8 m
6 ft.
1.8 m
6 ft.
1.8 m
*
*
4-1/2 ft.
1.4 m
14 ft.
4.3 m
14 ft.
4.3 m
14 ft.
4.3 m
*
*
1/2 ft.
H MAX. =14 ft. (4.6 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
V2
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.10
30
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Top Vent - Vertical Termination
Venting with four 90º elbows
V1 MIN.
Note: Use SLP Series
components only.
1-1/2 ft.
H1 MAX.
457 mm
4 ft.
1.2 m
V2 MIN.
4 ft.
1.2 m
H2 MAX.
4 ft.
1.2 m
V3 MIN.
3-1/2 ft.
1.0 m
V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 7.3).
V3
V2
H2
H1
V1
Figure 7.11
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
31
Rear Vent - Horizontal Termination
No Elbows
CAUTION
*For SL-950TR-E ONLY:
H1 Maximum can be up to 24 inches ONLY if the Optional
Refractory Kit (BRICK-950-E) is NOT used.
Note: Use DVP Series
components only.
H1 MAX
SL-550TR-E
24 in.
610 mm
SL-750TR-E
24 in.
610 mm
SL-950TR-E
18 in.*
457 mm
Figure 7.12
Rear Vent - Horizontal Termination
One 45º Elbow
H1 = 9 in. (229 mm) Maximum
For corner installation of models SL-550TR-E and SL-750TR-E ONLY
Note: Use DVP Series
components only.
Note: Do not use a 45º elbow
for SL-950TR-E. Use two 90º
elbows for corner installation on
SL-950TR-E.
Figure 7.13
32
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Rear Vent - Horizontal Termination
Venting with two 90º elbows
Note: Use DVP Series
components only.
H1 MAX.
V1 MIN.
H2 MAX.
1-1/2 ft. 457 mm
Back to back elbows
H1 + H2 MAX.
1 ft.
305 mm
2-1/2 ft.
762 mm
3 ft.
914 mm
1 ft.
305 mm
3 ft.
914 mm
6 ft.
1.8 m
5 ft.
1.5 m
3 ft.
914 mm
5 ft.
1.5 m
10 ft.
3.0 m
7 ft.
2.1 m
5 ft.
1.5 m
7 ft.
2.1 m
14 ft.
4.3 m
H1 MAX. = 7 ft. (2.1 m)
H1 + H2 MAX. = 14 ft. (4.3 m)
V1 + H1 + H2 MAX. = 40 ft. (12.2 m)
V1
H2
H1
Figure 7.14
Rear Vent - Horizontal Termination
Venting with three 90º elbows
Note: Use DVP Series
components only.
H1 MAX.
INSTALLED
HORIZONTALLY
V1 MIN.
1-1/2 ft.
457 mm
Back to back elbows
3-1/2 ft.
1.1 m
1 ft.
5-1/2 ft.
1.7 m
7-1/2 ft.
2.3 m
H2 + H3 MAX.
H1 + H2+ H3 MAX.
1 ft.
305 mm
2-1/2 ft.
762 mm
305 mm
2 ft.
610 mm
5-1/2 ft.
1.7 m
2 ft.
610 mm
4 ft.
1.2 m
9-1/2ft.
2.9 m
3 ft.
914 mm
6 ft.
1.8 m
13-1/2 ft.
4.1 m
H1 MAX. = 7-1/2 ft. (2.3 m)
H1 + H2+ H3 MAX. = 13-1/2 ft. (4.1 m)
V1 + H1 + H2+ H3 MAX. = 40 ft. (12.2 m)
H3
H2
V1
Figure 7.15
H1
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
33
Rear Vent - Vertical Termination
Venting with one 90º elbow
Note: Use DVP Series
components only.
V1 MIN.
H1 MAX.
1 ft.
305 mm
3-1/2 ft.
1.1 m
2 ft.
610 mm
5-1/2 ft.
1.7 m
3 ft.
914 mm
7-1/2 ft.
2.3 m
H MAX. = 7-1/2 ft. (2.3 m)
V1 + H1 MAX. = 40 ft. (12.2 m)
V1
H1
Figure 7.16
Note: Use DVP Series
components only.
Rear Vent - Vertical Termination
Venting with two 90º elbows
H1 + H2 MAX
V1
152 mm
Back to back elbows
2-1/2 ft.
762 mm
1 ft.
305 mm
4-1/2 ft.
1.4 m
2 ft.
610 mm
6-1/2 ft.
2.0 m
3 ft.
914 mm
H MAX. = 6-1/2 ft. (2 m)
V + H+ H1 MAX. = 40 ft. (12.2 m)
INSTALLED
HORIZONTALLY
H1
H2
Figure 7.17
34
V1 MIN.
1/2 ft.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Rear Vent - Vertical Termination
Venting with three 90º elbows
V1 MIN.
Back to back elbows
H1 MAX.
H2 MAX.
H1 + H2 MAX.
1-1/2 ft.
457 mm
1 ft.
305 mm
2-1/2 ft.
762 mm
1 ft.
305 mm
3-1/2 ft.
1.1 m
3 ft.
914 mm
6-1/2 ft.
2.0 m
2 ft.
610 mm
5-1/2 ft.
1.7 m
5 ft.
1.5 m
10-1/2 ft.
3.2 m
3 ft.
914 mm
7-1/2 ft.
2.3 m
7 ft.
2.1 m
14-1/2 ft.
4.4 m
H1 MAX. = 7-1/2 ft. (2.3 m)
H1 + H2 MAX. = 14-1/2 ft. (4.4 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
Note: Use DVP Series
components only.
V2
H2
V1
Figure 7.18
H1
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
35
Coaxial to Colinear Venting
The coaxial to colinear adapter (DV-46DVA-GCL) is approved for installations into solid fuel masonry or factory
built fireplaces that have been installed in accordance
with the National, Provincial, State and local building
codes. The DV-46DVA-GCL must be recessed into existing masonry fireplace. See Table 1 and Figure 7.20.
OUTSIDE FACE OF
FIREPLACE
EXHAUST VENT PIPE
TOP OF FIREPLACE
OPENING
5 IN. MIN.
INLET AIR VENT PIPE
EXHAUST VENT PIPE
3 IN. MIN.
SHADED AREA DEFINED AS
“INSIDE EXISTING MASONRY FIREPLACE”
Figure 7.19 Coaxial/Colinear Appliance Adapter (DV-46DVA-GCL)
WARNING! Risk of Fire! Coaxial to colinear venting
configuration may only be used in existing non-combustible chimney. Installation in any other venting application
could cause fire.
Prior to installing the gas appliance:
• Have the chimney and adjacent structure inspected
and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified
professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211
Level 2 inspection of the chimney.
• Replace component parts of the chimney and fireplace
as specified by the professionals.
• Ensure all joints are properly engaged and the chimney
is properly secured.
Table 1
CLEARANCE TO COMBUSTIBLES REQUIREMENTS
DV-46DVA-GCL
3 IN.
Exhaust Vent Pipe
5 IN.
Figure 7.20 Existing Fireplace DV-46DVA-GCL Clearance
Requirements
Clearances to Combustibles:
Refer to Section 5 for clearances to the appliance, mantel, mantel legs and wall projection.
Refer to Section 8 for pipe clearances to combustibles.
Termination Cap
For installation of termination cap see minimum vent
heights for various pitched roofs. See Section 6 of appliance owner’s manual.
Flue Damper
Fully lock the solid fuel fireplace’s flue damper in the open
position, OR completely remove it.
Venting Components
The LINK-DV30B is approved for use with the coaxial/colinear venting application. The LINK-DV30B kit includes:
• Two 30 feet sections of flexible vent pipe (3 inches Ø).
One section is used to draw combustion air and the other
section is used to expel exhaust gases.
• One vertical termination cap.
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL adapter and LINK-DV30B
kit. This may result in poor flame appearance, sooting,
pilot malfunction, or overheating.
36
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Connecting the DV-46DVA-GCL Adapter to Appliance
Top Vent
• Remove top seal cap and insulation if equipped. See
Section 14, “Appliance Setup.” Attach the DV-46DVAGCL adapter to the appliance starting collar with 3-1/2
in. self-tapping screws. See Figure 7.21.
Rear Vent
• Remove the rear seal cap and insulation if equipped.
Connect the DVP-2SL adapter to the vertically positioned
elbow. Follow installation instructions included with DVP2SL kit. Secure DV-46DVA-GCL adapter to DVP-2SL with
3-1/2 in. self-tapping screws. See Figure 7.21.
Connecting the LINK-DV30B to the DV-46DVA-GCL
adapter
• Insert the two sections of flexible vent pipe down the
existing chimney.
• Attach one section of flexible vent pipe to the exhaust
collar on top of the DV-46DVA-GCL adapter with three
self-tapping screws.
• Attach one section of flexible vent pipe to the inlet collar
on top of the DV-46DVA-GCL adapter with three selftapping screws.
• To minimize cold air drafts, seal around the flex vents
at the damper inside the chimney with non-combustible
unfaced fiberglass or rock wool insulation.
The DV-46DVA-GCL adapter must be recessed into existing
masonry fireplace. This measurement is taken from the top
of the fireplace opening. See Table 1 and Figure 7.20.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Do NOT connect this gas appliance to a chimney flue
serving a separate solid fuel or gas burning appliance.
• May impair safe operation of this appliance or other
appliances connected to the flue.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL
adapter and LINK-DV30B kit. This may result in poor flame appearance, sooting, pilot
malfunction, or overheating.
REAR VENT
TERMINATION CAP
TOP VENT
TERMINATION CAP
NOTICE: To achieve optimum performance of appliance, minimize or
avoid bends in exhaust vent pipe.
V
V
EXISTING CHIMNEY
EXISTING CHIMNEY
EXHAUST AIR
VENT PIPE
INLET AIR
VENT PIPE
EXISTING CHIMNEY
EXHAUST AIR
VENT PIPE
INLET AIR
VENT PIPE
EXISTING CHIMNEY
To minimize cold air
drafts, seal with
non-combustible
insulation.
DIRECT VENT FIREPLACE
To minimize cold air
drafts, seal with
non-combustible
insulation.
DIRECT VENT FIREPLACE
HEARTH
FLOOR
FLOOR
HEARTH
H
V
H
V
Minimum
10 ft.
3.05 m
0 ft.
0 mm
Minimum
10 ft.
3.05 m
Maximum
40 ft.
12.2 m
2 ft.
610 mm
Maximum
40 ft.
12.2 m
Figure 7.21
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
37
8
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B.)
attached to them.
• See Section 10.L for information for regarding the installation of a horizontal termination cap.
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
Failure to keep insulation or other material away from
vent pipe may cause overheating and fire.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
‡DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
‡,IZDOOWKLFNQHVVLVOHVVWKDQLQWKHH[LVWLQJKHDWVKLHOGVPXVWEHILHOGWULPPHG,I
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
‡SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
‡,IZDOOWKLFNQHVVLVOHVVWKDQWKHH[LVWLQJKHDWVKLHOGVPXVWEHILHOGWULPPHG
,IZDOOWKLFNQHVVLVJUHDWHUWKDQLQD'93+60%ZLOOEHUHTXLUHG
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter
one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
WALL
3 in. (76 mm)
top clearance *
Heat
Shield
Heat
Shield
Wall
Shield
Firestop
1 in. (25 mm)
clearance
bottom & sides
10 in.
10 in.
10 in.
12 in.
A*
WALL
SL-550TR-E
SL-750TR-E
SL-950TR-E
D
B*
* When using SLP pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are:
Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
C
in.
mm
in.
mm
in.
mm
A*
37
940
41
1041
45
1143
B*
24-3/8
619
27-7/8
708
31-7/8
810
C
36
914
40
1016
44
1118
D
23-3/8
594
26-7/8
683
30-7/8
784
* Shows center of vent framing hole for top or rear venting.
The center of the hole is one (1) inch (25.4 mm) above the
center of the horizontal vent pipe.
Figure 8.2 Wall Penetration
38
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 8.3).
ATTIC ABOVE
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 8.3).
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
A
• The ceiling firestop may be installed above or
below the ceiling joists when installed with an
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.4.
• Secure with three fasteners on each side.
A
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
D. Install Attic Insulation Shield
PIPE
A
DVP
10 in. (254 mm)
SLP
9 in. (229 mm)
WARNING! Fire Risk. DO NOT allow loose
materials or insulation to touch vent. Hearth
& Home Technologies requires the use of an
attic shield.
The International Fuel Gas Code requires an
attic shield constructed of 26 gauge minimum
steel that extends at least 2 in. (51 mm) above
insulation.
• Attic insulation shields must meet specified
clearances to combustible materials and be
secured in place.
• An attic insulation shield kit is available from
Hearth & Home Technologies. Contact your
dealer to order. Install attic insulation shield
according to instructions included with kit.
Figure 8.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
CEILING FIRESTOP
INSTALLED BELOW CEILING
CEILING FIRESTOP
INSTALLED ABOVE CEILING
Figure 8.4 Installing the Attic Shield
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
39
9
Appliance Preparation
A. Top Vent
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
Note: Actual unit may look different than the fireplace shown
in this section.
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
2 SCREWS
Figure 9.4 Remove the seal cap.
Figure 9.1 For top vent, remove the two screws holding the
top heat shield in place. For rear vent, see Section 9B.
WARNING! Risk of Fire! Do not remove heat shield. Elevated header temperatures may cause a fire.
Figure 9.2 Rotate the top heat shield to the vertical
position as shown above. The heat shield must remain in
the vertical position.
Figure 9.5 Remove the insulation basket and white insulation from the center vent pipe.
2 SCREWS
Figure 9.3 Replace the two screws as shown.
40
Figure 9.6 Remove the insulation from the outer vent pipe.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
NOTICE: Once the seal cap has been removed it CANNOT
be reattached.
2 SCREWS
Figure 9.7 To attach the first section of vent pipe, make
sure to use the fiberglass gasket to seal between the first
vent component and the outer fireplace wrap. Use 2 selftapping screws to secure the gasket to the outer wrap.
Figure 9.10 Fold the center parts of the retaining band
out and use to remove the seal cap.
Note: Once the vent cap has been removed, it cannot be
reattached.
B. Rear Vent
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
Figure 9.11 Discard the seal cap, remove and discard
the insulation basket. Note: Once the vent cap has been
removed it CANNOT be reattached.
Figure 9.8 Fold the tabs toward the center of the fire plug
(90°) and remove the insulation gasket.
Figure 9.9 Cut the metal retaining band and fold the
sides out.
Figure 9.12 Attach the first vent section (it will snap into
place). Slide the insulation gasket onto the vent section,
up against the appliance and over the tabs. Use two selftapping screws to secure gasket to outer wrap.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
41
C. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air space clearance may cause
overheating and fire.
The diagram shows how to properly position and secure
the appliance (see Figure 9.13). Nailing tabs are provided
to secure the appliance to the framing members.
• Bend out nailing tabs on each side.
NAILING TABS
BOTH SIDES
• Place the appliance into position.
• Keep nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
Figure 9.13 Proper Positioning and Securing of an Appliance
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
42
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
10
Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with silicone with a
minimum of 300ºF continuous exposure rating, including the
slip section that connects directly to the horizontal termination cap.
Figure 10.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1
A
Lances
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Assemble Pipe Sections
B
Figure 10.3
Figure 10.2
Note: Make sure that the seams are not aligned to prevent
Per Figure 10.2:
unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90° and 45° elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
Figure 10.4 Seams
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
INCORRECT
43
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.6.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Slide together to the desired length.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 10.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration. Caulk with a minimum of 300ºF continuous exposure
rating may be used to hold the part in place.
• Continue adding vent components, locking each
succeeding component into place.
Pilot hole
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
Figure 10.6 Slip Section Pilot Holes
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with silicone with a minimum of
300ºF continuous exposure rating, including the slip section
that connects directly to the horizontal termination cap.
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 10.7.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1.
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 10.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
Figure 10.5 Adding Venting Components
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed
using a high temperature silicone sealant (300ºF minimum
continuous exposure rating).
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
44
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs originating off the top of the appliance, with
no offsets, must be supported every 8 ft. (2.44 m) after
the maximum allowed 25 ft. (7.62 m) of unsupported rise.
• Rotate either section (see Figure 10.10) so the seams
on both pipe sections are aligned as shown in Figure
10.11.
• Vertical runs originating off the rear of the appliance, or
after any elbow, must be supported every 8 ft. (2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal runs must be supported every 5 feet (1.52
m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support vent sections. See Figures 10.8
and 10.9.
• Wall shield firestops may be used to provide horizontal
support to vent sections.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 10.10 Rotate Seams for Disassembly
120º
Figure 10.11 Align and Disassemble Vent Sections
Figure 10.8 Securing Vertical Pipe Sections
120º
Figure 10.9 Securing Horizontal Pipe Sections
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
45
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
high temperature silicone (300ºF minimum continuous
exposure rating) to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
A decorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 10.12
• Remove shingles or other roof covering as necessary
to cut the rectangular hole for the support box. Cut the
hole 1/8 in. (3 mm) larger than the support box outline.
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
10.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
46
Figure 10.13
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
G. Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 10.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.15.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Figure 10.15
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
H. Assemble and Install Storm Collar
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
•
•
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................ 2.5*
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
Slide the storm collar onto the exposed pipe section
and align brackets.
Insert a bolt (provided) through the brackets and install
nut. Do not completely tighten.
Figure 10.16 insert Bolt into Brackets
* 3 foot minimum in snow regions
Figure 10.14 Minimum Height From Roof To Lowest Discharge
Opening
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
•
Slide the assembled storm collar down the pipe section
until it rests on the roof flashing. See Figure 10.16.
•
Tighten nut and make sure the collar is tight against the
pipe section.
•
Caulk around the top of the storm collar. See Figure 10.17
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.15.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
47
I. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of
the cap into the outer flue of the pipe. See Figure 10.17.
K. Heat Shield Requirements for Horizontal
Termination
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.19).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
Termination Cap
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.19.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
Screws
Storm
Collar
• Use an extended heat shield if the finished wall thickness
is greater than 7-1/4 in. (184 mm).
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
Caulk
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 10.17
J. Install Decorative Wall Components (SLP
only)
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the wall shield firestop.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have
been connected, slide the wall thimble up to the interior
wall surface and attach with screws provided. See Figure
10.18.
Figure 10.18 Wall Thimble
48
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
L. Install Horizontal Termination Cap (DVP
and SLP Pipe)
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
WALL SHIELD
FIRESTOP
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
SLIP SECTION
CAN BE EXTENDED
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 10.19 Venting through the wall
Termination Cap Specification Chart
(depth without using additional pipe sections)
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Rear Vent
Top Vent
Rear Vent
Depth
Depth
Depth
Depth
3-1/8 in. to
5-1/2 in. to
N/A
N/A
5 in.
9-1/2 in.
SL Series
DVP-HPC1
Top Vent
Depth
N/A
DVP-HPC1
Rear Vent
Depth
3-1/8 in. to
5-1/4 in.
DVP-HPC2
Top Vent
Depth
N/A
DVP-HPC2
Rear Vent
Depth
5-1/4 in. to
9-3/8 in.
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
49
11
Gas Information
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 16 for location of gas line
access in appliance.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
• Gas line may be run through knockout(s) provided.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pressure requirements are:
Gas Pressure
• The gap between supply piping and gas access hole may
be caulked with caulk with a minimum of 300ºF continuous
exposure rating or stuffed with non-combustible, unfaced
insulation to prevent cold air infiltration.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Natural Gas
Propane
Minimum inlet pressure
5.0 in. w.c.
11.0 in. w.c.
• A small amount of air will be in the gas supply lines.
Maximum inlet pressure
10.0 in. w.c.
13.0 in. w.c.
Manifold pressure
3.5 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in. (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
50
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
12
Electrical Information
A. Wiring Requirements
B. Intellifire Ignition System Wiring
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• Wire the appliance junction box to 110-120 VAC. This is
required for use of optional accessories (standing pilot
ignition) or proper operation of the appliance (Intellifire
ignition).
• Wire the appliance junction box to 110-120 VAC for
proper operation of the appliance.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
• Low voltage and 110-120 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
Determine if the appliance uses an Intellifire ignition system or standing pilot ignition system:
• Open the control access panel or remove the decorative
front.
• A red or black ignitor button (as shown in Figure 12.1)
indicates this appliance is standing pilot ignition.
RED OR
BLACK
BUTTON
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• Refer to Figures 12.2 and 12.3, Intellifire Pilot Ignition
(IPI) Wiring Diagram.
• This appliance is equipped with an Intellifire control valve
which operates on a 3 volt system.
• Plug the 3-volt AC transformer into the appliance junction
box to supply power to the unit OR install two D cell
batteries (not included) into the battery pack before use.
NOTICE: Batteries should not be placed in the battery
pack while using the transformer. Remove batteries before
using the transformer, and unplug the transformer before
installing the batteries. Battery polarity must be correct or
module damage will occur.
C. Standing Pilot Ignition System Wiring
• The standing pilot ignition system wiring does not require
a 110 VAC supply to operate. See Figure 12.4.
• A 110 VAC junction box MUST be installed for use with
a fan or remote control. See Figure 12.5 for junction box
wiring. Keep wire lengths short as possible.
NOTICE: DO NOT wire 110-120 VAC to the millivolt valve!
This will damage the valve.
• If using a thermostat use one compatible with a millivolt
gas valve system:
- Install the thermostat in the location as indicated in the
thermostat instructions to ensure proper operation of
appliance.
- Use low resistance thermostat wire for wiring from
ignition system to the wall switch and thermostat.
- Keep wire lengths short as possible.
Figure 12.1 Ignitor Button
D. Optional Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
51
IGNITION MODULE 3 VAC
INTERMITTENT PILOT IGNITOR
I
S
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 110-120 VAC
is required at junction box unless equipped
with battery back-up.
TRANSFORMER
3 VAC
WHITE
NEUTRAL
HOT
PLUG IN
ORANGE
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
WIRES
(TO BROWN)
GREEN
ORANGE
BATTERY PACK
WIRE ASSEMBLY
VALVE
Figure 12.2 Intellifire Ignition Wiring Diagram with Wall Switch or Thermostat
IGNITION
MODULE 3 VAC
NOTE: 1. Ignition module, valve, pilot, and
wall switch operate on 3 volts. 110-120 VAC
is required at junction box unless equipped
with battery back-up.
INTERMITTENT
PILOT IGNITOR
I
S
TRANSFORMER
3 VAC
ORANGE
NEUTRAL
HOT
WHITE
PLUG IN
GROUND TO
FIREPLACE
CHASSIS
K
AC
BL
D
RE
ORANGE
REMOTE
PLUG IN
VALVE
Figure 12.3 Intellifire Ignition Wiring Diagram with Remote Receiver
52
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
GREEN
WIRES
(TO BROWN)
BATTERY PACK
PILOT
THERMOPILE
THERMOCOUPLE
PIEZO
RED
THERMOSTAT
WIRE ASSEMBLY
WHITE
VALVE
Figure 12.4 Standing Pilot Ignition Wiring Diagram
E. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
Romex
Connector
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
14/2WG
Cover Plate
outside firebox
F. Junction Box Installation
If the box is being wired from the INSIDE of the appliance:
HT
WHT B
LK
BLK
W
• Remove the screw attaching the junction box/receptacle
to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 12.5).
• Pull the electrical wires from outside the appliance through
the opening into the valve compartment and secure wires
with a Romex connector. See Figure 12.5.
• Make all necessary wire connections to the junction box/
receptacle and reattach the junction box/receptacle to
the outer shell.
Copper
ground attached
to GRN screw with
GRN wire
GRN wire
inside box
NOTICE: DO NOT wire 110 -120 VAC
to wall switch.
Figure 12.5 Junction Box Detail
G. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted switch for use
with a fan (See Figure 12.6):
• The power can then be supplied from the switch box to
the appliance using a minimum of 14-3 with ground wire.
Switch
Minimum 14-3 AWG
with Ground
Red
Black
White
Green
Junction Box
• At the switch box connect the black (hot) wire and red
(switch leg) wire to the wall switch as shown.
Switch Box
• At the appliance connect the black (hot), white (neutral)
and green (ground) wires to the junction box as shown.
• Add a 1/4 in. insulated female connector to the red
(switch leg) wire, route it through the knockout in the face
of the junction box, and connect to the top fan switch
connector (1/4 in. male) as shown.
Black
White
Green
Red
Black
White
Green
• The power supply for the appliance must be brought into
a switch box.
Power
Supply
Wires
Knockout
Red
Figure 12.6 Junction Box Wired to Wall Switch or BC10
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
53
13
Finishing
A. Splatter Guard
The splatter guard is a piece of corrugated material
used to protect the appliance during the installation
process before finishing work on the whole hearth is
complete. Splatter guards may be factory installed or
accompany the decorative front of the unit, depending
on the fireplace model. Splatter guards must be removed before appliance is fired.
WARNING! Risk of Fire! Close the ball valve before installing the splatter guard to prevent accidental lighting.
Remove the splatter guard before lighting the appliance.
Step 1. Turn off gas to valve. Red gas shutoff knob is
located on ball valve. Disconnect the 3 volt transformer
from the junction box. See Figure 13.1.
Figure 13.3
Step 4. Center the splatter guard in front of the unit as
shown in Figure 13.4. Place the splatter guard in the unit
by guiding the top flap into proper position and then continuing to guide the tabs on the side flaps into the top slot
on the left and right sides of the appliance. The top slot
is indicated in Figure 13.5 Take care not to bend or break
off the tabs.
Figure 13.1
To install the Splatter Guard:
Step 2. Crease flap on top side of splatter guard using the
scored line as the guide. See Figure 13.2.
Figure 13.4
TOP SLOT
Figure 13.2
Step 3. Crease flaps on left and right sides of splatter guard
using the scored line as the guide. See Figure 13.3.
54
Figure 13.5
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Step 5. Fold bottom flap along score line as indicated in
Figure 13.6 and tuck into valve access area of appliance.
Splatter guard should fit securely on front of unit.
Figure 13.9
Once plumbing and wiring are complete on the fireplace,
the lower access panel may be closed until the time that the
splatter guard must be removed for firing the appliance.
Figure 13.6
Figure 13.10
To Close the Lower Access Panel:
Figure 13.7
Step 6. To open lower access panel of splatter guard,
place one hand above score line and place two fingers
from other hand in the round holes on the front of the
splatter guard. See Figure 13.7. Pull out and fold up
the panel as shown in Figure 13.8. Disengage the tabs
on left and right bottom of splatter guard and fit them
into the square holes. The tabs are now inside the front
of the splatter guard; carefully bend them down. See
Figure 13.9.
Carefully disengage the tabs from the square holes and
bend the access panel to its original position. Bend the
center bottom flap and insert it into the bottom of the appliance.
Figure 13.11
To Remove the Splatter Guard:
Figure 13.8
Carefully grab splatter guard on or near the vertical center
on the left and right sides. Pull outward gently, but firmly,
taking care not to tear or remove the inserted tabs.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
55
B. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply
could cause fire.
CEILING
All measurements are in inches.
12
10
9
5
3
6
7
8
32
5
6
7
8
2-7/8 IN.
MINIMUM
3 FT. MAXIMUM
Note: Clearance from opening
to perpendicular wall.
11
4
4
1/2 IN.
MINIMUM
9
10
11
12
Figure 13.14 Mantel Leg (Acceptable on both sides of opening.)
13
3 IN.
MINIMUM
TOP OF HOOD OR FIREPLACE OPENING
5-3/8 IN.
MINIMUM
Figure 13.12 Clearances to Mantels or other Combustibles
above Appliance
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
Figure 13.15 Wall Projection (Acceptable on one side of opening.)
1/2 in. SHEETROCK
OR COMBUSTIBLE
MATERIAL
3-1/2 in.
1/2 in.
SHEETROCK
3-1/2 in.
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
1/2 in.
1/2 in.
NON-COMBUSTIBLE ZONE
Figure 13.16 Non-Combustible Zone
Models: SL-950TR-E, SL-950TR-IPI-E
Figure 13.13 Non-Combustible Zone
Models: SL-550TR-E, SL-750TR-E
SL-550TR-IPI-E, SL-750TR-IPI-E
56
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
C. Facing Material
• Metal front faces may be covered with non-combustible
materials only.
• Facing and/or finishing materials must not interfere
with air flow through louvers, operation of louvers or
decorative fronts, or access for service.
• Facing and/or finishing materials must never overhang
into the glass opening.
TOP SEAL
JOINT
SIDE SEAL
JOINT
3 IN.
(76 mm)
• Observe all clearances when applying combustible
materials.
• Seal joints between the finished wall and appliance top
and sides using a 300°F minimum sealant. Refer to
Figure 13.17.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of decorative fronts and
louvers.
FINISH WALL MATERIAL
MAY BE COMBUSTIBLE
TOP AND SIDES
0 IN.
(0 mm)
NON-COMBUSTIBLE STRIP
SHIPPED WITH UNIT
Figure 13.18 Facing Materials
Models: SL-950TR-E, SL-950TR-IPI-E
FACING MATERIAL UP TO 1/2 IN. THICK
MAY BE COMBUSTIBLE - TOP AND SIDES
0 IN.
1 IN.
1 IN.
0 IN.
0 IN.
HIGH TEMPERATURE (300 ºF/ 149 ºC MIN.)
TOP AND SIDE SEAL JOINT
BOTTOM 1 INCH (SHADED AREA)
MAY BE COVERED WITH COMBUSTIBLE
OR NON-COMBUTIBLE MATERIAL
Figure 13.17 Facing Materials
Models: SL-550TR-E, SL-750TR-E
SL-550TR-IPI-E, SL-750TR-IPI-E
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
57
D. Decorative Fronts
Only decorative fronts certified for use with this appliance
model may be used. Contact your dealer for a list of decorative fronts that may be used. Once you have determined what kind of decorative front and finishing material
is going to be used on the fireplace, use the information
below which shows the decorative front models and the
non-combustible finishing material thickness allowed.
FRONT FACE OF FIREPLACE
1 in. MAX
FINISHING MATERIAL
(TOP EDGE)
DECORATIVE FRONT
Finishing materials 1 inch maximum thick.
Stop finishing material flush with opening.
Figure 13.21 Overlap Fit Decorative Front (Chateau and Halston)
DECORATIVE FRONT
FINISHING MATERIAL
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
4 IN. MAXIMUM THICKNESS
Stop finishing material flush with fireplace surround opening.
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
Figure 13.19 Inside Fit Decorative Front (Folio)
DECORATIVE FRONT
= NON COMBUSTIBLE ZONE
Y
X
(Includes approximately 1/8 in. opening each side of door)
Finishing material up to 4 inches thick may come to the
appliance surround opening on the sides and cover the top
and bottom vanity panels.
Finishing material between 1 and 4 inches thick.
Refer to Figure 16.3 for X and Y dimensions.
Figure 13.22 Inside Fit Decorative Front (Chateau and Halston)
Figure 13.20 Inside Fit Decorative Front (Clean Face)
58
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
E. Elevated Hearth Systems
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various
dimensions. Some hearth systems will elevate the appliance off the floor at a given dimension. For example, if appliance
will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 in. The 9-1/4 in. elevation will also
have to be added to the following: Wall penetration referenced in Figure 8.2 (Wall penetration) and Rough Opening Height
(header height) referenced in Figure 5.2. Note: Finished floor thickness should also be considered when determining installation dimensions.
MODEL
SL-550
SL-750
SL-950
DESCRIPTION
PART #
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
KENWOOD CABINET
KENWOOD CABINET W/ BASE
KENWOOD CORNER CABINET
KENWOOD CORNER CABINET W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
KENWOOD MANTEL
KENWOOD MANTEL W/ BASE
KDC44SBP
KDC44SBP W/ HTKDC44SBP
KDA44SBP
KDA44SBP W/ HTKDA44SBP
AFKDMPA
AFKDMPA W/ HTKDMPA
KDC48DBP
KDC48DBP W/ HTKDC48DBP
KDA48SBP
KDA48SBP W/ HTKDA48SBP
AFKDMPB
AFKDMPB W/ HTKDMPB
AFKDMPC
AFKDMPC W/ HTKDMPC
ELEVATED APPLIANCE
DIMENSION
See Note 1
0
9-1/4 in.
0
9-1/4 in.
0 (See Note 3)
9 1/4 in.
0
9-1/4 in.
0
9-1/4 in.
0 (See Note 3)
9-1/4 in.
0 (See Note 3)
9-1/4 in.
MARBLE LEG CUT
LENGTH
See Note 2
29-3/8 in.
29-3/8 in.
29-3/8 in.
29-3/8 in.
27-3/8 in.
29-3/8 in.
32-7/8 in.
32-7/8 in.
32-7/8 in.
32-7/8 in.
27-3/8 in.
29-3/8 in.
32-7/8 in.
32-7/8 in.
Note 1. Add dimensions to Wall Penetration (Figure 8.2) and Rough Opening Height (Figure 5.2).
Note 2. Verify Marble Cut Lengths on site prior to cutting.
Note 3. Dimensions assume use of a 3/4 in. Hearth Pad.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
59
14
Appliance Setup
A. Remove Fixed Glass Assembly
Placing the Lava Rock
See Section 14.G.
See Section 14F for Lava Rock placement instructions.
B. Remove the Shipping Materials
• Place lava rock on base pan. Do NOT place on burner
top.
Remove shipping materials from inside or underneath the
firebox.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Placing the Ember Material
Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT be placed directly over ports. See
Figure 14.4 for the only exception to this guideline. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• When placing Glowing Embers® onto the burner care
should be taken so that the ports are not covered. Place
the dime-size ember pieces near the port holes in the
burner top (see Figure 14.3). Failure to follow this procedure will likely cause lighting and sooting problems.
• Some of the small port holes should be covered with
ember material. See Figure 14.4 for detail.
• Save the remaining ember materials for use during appliance servicing. The embers provided should be enough
for 3 to 5 applications.
NO EMBERS
RHEOSTAT
SWITCH
TEMPERATURE
SENSOR
Figure 14.1 Blower wiring
VARIABLE
SPEED SWITCH
LO
G
JUNCTION BOX
Figure 14.3 Placement of Embers
TEMPERATURE
SENSOR SWITCH
BLUE
Figure 14.2 Detail of Fan Wiring with Rheostat
E. Lava Rock, Mineral Wool/Ember Placement
WARNING! Risk of Explosion! Follow ember placement
instructions in manual. DO NOT place embers directly over
burner ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.
Figure 14.4
60
PORT HOLES IN CIRCLED
AREA SHOULD BE COVERED
WITH EMBER MATERIAL. NO
OTHER PORT HOLES MAY
COME INTO CONTACT WITH
EMBER MATERIAL.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
F. Install the Log Assembly
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the following instructions.
Log Set Assembly: LOGS-550-E, 750-E, 950-E
Model: SL-550TR-E, 750TR-E, 950TR-E,
SL-550TV-E, SL-750TV-E, SL-950TV-E
Note: Figure 1 illustrates the recommended gap between the
burner and the lava rock retainer.
3/8 in.
Burner
Carefully remove the logs from the packaging.
CAUTION: LOGS ARE FRAGILE! Handle with care.
SRV2118-701
SRV2121-701
Log 2
SRV2115-702
SRV2118-702
SRV2121-702
Log 3
SRV2115-703
SRV2118-703
SRV2118-703
Log 4
SRV2115-704
SRV2118-704
SRV2121-704
Log 5
SRV2115-705
SRV2118-705
SRV2121-705
Lava rock
retainers
NE
SRV2115-701
ZO
Log 1
CK
SL-950TR-E
SL-950TV-E
RO
SL-750TR-E
SL-750TV-E
VA
LA
SL-550TR-E
SL-550TV-E
PLACE LAVA ROCK
BETWEEN LAVA ROCK
RETAINERS
Figure 1
Left rear log tab
Right rear log tab
Indentation
Shoulder screw
1
Lava rock retainer
Grate tine (4)
Slot
Figure 2
Figure 3
Left rear log tab
Log # 2 should touch firebox
Indentation
1
2
Mate slot with tab
Figure 5
Figure 4
Log #1: Locate the slot on the bottom right side of log 1.
Mate the slot with the right rear log tab. Pull the left end of
log #1 forward until it touches the left rear log tab.
Mate notch with grate tine
Log #2: Mate the far left grate tine with the notch located
on the left end of log #2. The right end of log #2 should rest
on log #1 as shown. Be sure that the top of log # 2 touches
the back of the firebox.
2118-935E 6/13
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
61
Log should touch lava rock retainer
3
3
Pin hole
Figure 6
Figure 7
Mate shoulder screw with pin hole
Log #3: Locate the pin hole on the underside of log #3.
Mate the pin hole with the shoulder screw located on the
burner top. Push the left end of log # 3 toward the back of
the firebox until it touches the lava rock retainer.
Bump
Bump
Swing knot towards log #3
5
4
Figure 8
Mate notch with grate tine
Log #4: Locate the notch at the end of log # 4. Mate the
notch with the tine as shown above. The top end of log #4
should rest between the end of log #2, and the bump located
on log #1. Swing the knot on log # 4 towards log #3.
Mate notch with grate tine
Figure 9
Log #5: Locate the notch at the end of log # 5. Mate the
notch with the far right grate tine. The top end of log # 5
should rest on the right side of the “bump” as shown above.
You may need to move log #4 slightly.
WARNING
RISK OF EXPLOSION!
• Place lava rock according to instructions.
• Do NOT place lava rock on burner top.
• Do NOT place lava rock in a position that they may
fall into pilot area.
• Improperly placed lava rock interferes with proper
burner operation.
Figure 10
Lava Rock
Step #6: Apply the supplied lava rock as shown above. Place
an even layer of lava rock in zone shown in Figure 1. The
amount should be just enough to cover the metal surface.
Take care to ensure that no lava rock is placed outside the
zone indicated in Figure 1.
62
Delayed ignition could occur.
• Use ONLY Hearth & Home Technologies-approved
lava rock.
• Some models may not require use of entire contents
of bag.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
G. Fixed Glass Assembly
I. Air Shutter Setting
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
This appliance has an adjustable air shutter (which controls the primary air) factory set for the minimum vertical
vent run (see Figure 14.4). If your installation has more
than the minimum required vertical vent length, adjustment of the air shutter may be necessary to obtain optimal flame appearance. This should be adjusted by a
qualified installer at the time of installation.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
• Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 14.5).
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
By sliding the air shutter to the right, you will be closing
the air shutter. To adjust loosen the wing nut. Care should
be taken when adjusting the air shutter so as not to cause
the appliance to soot. If sooting occurs the air shutter will
need to be opened by sliding the air shutter to the left.
When finished, tighten wing nut.
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
LATCHES
(BOTH BOTTOM
AND TOP)
GLASS
ASSEMBLY
SHUTTER ADJUSTMENTS
Figure 14.5 Fixed Glass Assembly
H. Install Trim and/or Surround
• Install optional trim kits and/or surrounds using the
instructions included with the accessory.
• Use non-combustible materials to cover the gap between
the sheet rock and the appliance (when applicable to the
model).
Figure 14.6 Air Shutter
Shutter Settings
Models
NG
LP
SL-550TR-E
SL-550TR-IPI-E
3/16 in.
3/16 in.
SL-750TR-E
SL-750TR-IPI-E
3/16 in.
3/16 in.
SL-950TR-E
SL-950TR-IPI-E
3/8 in.
Full Open
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
63
15
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. Standing Pilot Ignition System
Symptom
1. After repeated triggering
of the red or black piezo
ignitor button, the spark
ignitor will not light the
pilot.
2. The pilot will not stay lit
after carefully following
the lighting instructions.
Possible Causes
Corrective Action
A. No gas or low gas pressure.
Check the remote shut-off valves from the appliance. Usually, there
is a valve near the gas main. There can be more than one valve between the appliance and the main.
B. No lp in tank.
Check the LP (propane) tank. You may be out of fuel.
C. Ignitor.
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor. Verify that there is no
short in electrode wire.
D. Pilot or misaligned electrode
(spark at electrode).
Using match, light the pilot. If the pilot lights, turn off the pilot and
trigger the piezo ignitor button again. If the pilot lights, an improper
gas/air mixture caused the bad lighting and a longer purge period is
recommended. If the pilot will not light, ensure the gap at the electrode and pilot is one-eighth in. to have a strong spark. If the gap is
OK, replace the pilot.
A. Thermocouple.
Check that the pilot flame impinges on the thermocouple. Adjust the
pilot for proper flame impingement.
Ensure that the thermocouple connection at the gas valve is fully inserted and tight (hand tighten plus 1/4 turn).
Verify proper voltage output from the thermocouple to the valve.
Place one millivolt meter lead wire on the thermocouple copper lead.
Place the second lead wire on the solder button on the back of the
valve (blue wire). Start the pilot and hold the valve knob in. The millivolt reading should read 8-16 millivolts. If millivolt reading is less
than 8 millivolts, replace thermocouple.
3. The pilot is burning,
there is no burner
flame, the valve knob is
in the ON position, and
the ON/OFF switch is in
the ON position.
B. Improper gas inlet pressure.
Natural gas should be 5-14 in. w.c. LP should be 10-14 in. w.c. Verify
pressure with manometer.
C. Valve.
If the thermocouple is producing 8-16 millivolts, replace control valve.
A. ON/OFF switch or wires.
Check the ON/OFF switch and wires for proper connections. Place
the jumper wires across the terminals at the ON/OFF switch. If the
burner comes on, replace the ON/OFF switch. If the ON/OFF switch
is OK, place the jumper wires across the ON/OFF switch wires at the
gas valve. If the burner comes on, the wires are faulty or connections
are bad.
B. Thermopile may not be generating sufficient millivoltage.
Check that the pilot flame impinges thermopile properly.
Be sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millivolt meter. Take the reading at THTP&TP terminals of the gas valve. The meter should read 350 millivolts minimum, while holding the valve knob depressed in the pilot
position, with the pilot lit, and the ON/OFF switch in the OFF position.
Replace the thermopile if the reading is below the specified minimum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The reading
should be 350 millivolts minimum. Replace the thermopile if the reading is below the minimum.
64
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Troubleshooting (continued)
Symptom
3. (Continued)
Possible Cause
Corrective Action
C. Valve.
Turn the valve knob to the ON position. Place the ON/
OFF switch in the ON position. Take a reading with a
millivolt meter at the thermopile terminals. The millivolt
meter should read greater than 125mV. If the reading
is acceptable, and if the burner does not come on, replace the gas valve.
D. Plugged burner orifice.
Check the burner orifice for stoppage. Remove stoppage.
E. Wall switch or wires.
Check the wall switch and wires for proper connections. Place the jumper wires across the terminals at
the wall switch. If the burner comes on, replace the
wall switch. If the wall switch is OK, place the jumper
wires across the wall switch wires at the gas valve. If
the burner comes on, the wires are faulty or connections are bad.
4. Frequent pilot outage A. Pilot flame may be too high or too low, or blowproblem.
ing out (high pressure), causing pilot safety to
drop out.
Clean thermocouple and adjust the pilot flame for
proper flame impingement. Follow lighting instructions
carefully.
5. The pilot and main
burner extinguish
while in operation.
A. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
B. Improper gas inlet pressure.
Natural gas should be 5-14 in. w.c. LP should be 1014 in. w.c. Verify pressure with manometer.
C. Inner vent pipe leaking exhaust gases back
into the system.
Check venting system for damage. Replace/repair improperly assembled pipe sections.
D. Glass installed improperly.
Check to ensure glass is installed properly. Replace
fixed glass panel assembly.
E. Thermopile or thermocouple.
Replace pilot if necessary.
F. Improper vent cap installation.
Check for proper installation and freedom from debris
or blockage.
A. Flame impingement.
Adjust the log set so that the flame does not excessively impinge on it. Refer to log instructions.
B. Improper air shutter setting.
Refer to manual for shutter set points. Ensure that set
point is correct for appliance/gas type. If unit has adjustable shutter, it may be necessary to increase shutter opening.
C. Debris around air shutter.
Inspect the opening at the base of the burner. NO MATERIAL SHOULD BE PLACED IN THIS OPENING.
A. Insufficient oxygen being supplied.
Ensure that the vent cap is installed properly and free
of debris. Ensure that the vent system joints are tight
and have no leaks.
6. Glass soots.
7. Flame burns blue
and lifts off burner.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
65
B. Intellifire Ignition System
Symptom
Possible Cause
1. Pilot won’t light.
A. Incorrect wiring.
The ignitor/module
makes noise, but no
B. Loose connections or electrical
spark.
shorts in the wiring.
2. Pilot won’t light,
there is no noise or
spark.
3. Pilot sparks, but
Pilot will not light.
66
Corrective Action
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify connections are not grounding out to metal
chassis, pilot burner, pilot enclosure, mesh screen if present, or any
other metal object.
C. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
D. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5
mm) away from “I” terminal on module. Place ON/OFF rocker switch
or wall switch in ON position. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode. Replace pilot if necessary.
A. No power or transformer installed
incorrectly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
B. A shorted or loose connection in
wiring configuration or wiring harness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
Verify that 110-120 VAC power is “ON” to junction box.
D. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
E. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF rocker switch or wall
switch in ON position. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits, inlet pressure must not
exceed 14 in. W.C.
B. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
D. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is below 2.7.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Intellifire Ignition System - (continued)
Symptom
4. Pilot lights but continues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
Possible Cause
A. A shorted or loose connection in flame
sensing rod.
Corrective Action
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure or screen if present, or any other metal
object.
B. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is enflame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. Verify correct pilot orifice is installed and gas inlet is set to pressure
specifications. Polish flame sensing rod with fine steel wool
to remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to the
module.
D. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod
is not cracked, damaged, or loose. Verify connection from
flame sensing rod to white sensor wire. Polish flame sensing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multimeter with ohms set at lowest range.
Replace pilot if any damage is detected.
E. Module.
Turn ON/OFF rocker switch or wall switch to OFF position.
Remove ignitor wire “I” from module. Place ON/OFF rocker
switch or wall switch in ON position. If there is no spark at “I”
terminal module must be replaced. If there is a spark at “I”
terminal, module is fine.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
67
16
Reference Materials
A. Appliance/Decorative Front Dimension Diagrams
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
N
O
P
M
Q
L
ØR
GAS LINE ACCESS
ØK
C
E
I
D
V
H
F
S
B
T
U
A
SL-550TR-E

G
SL-750TR-E
Location
Inches
Millimeters
Inches
Millimeters
A
36
913
41
1041
B
31-1/8
791
36-1/8
917
C
27-3/16
691
32-1/16
815
D
18-1/16
459
21-1/2
547
E
34-1/16
865
37-5/8
955
F
3-9/16
90
3-9/16
90
G
6-7/8
174
6-7/8
174
H
23-3/8
594
26-7/8
683
I
34-3/8
873
37-7/8
962
J
36-7/16
926
39-15/16
1015
K
8
203
8
203
L
8-13/16
223
8-13/16
223
M
16-5/16
415
16-5/16
415
N
1/2
13
1/2
13
O
25-3/4
653
30-3/4
781
391
P
12-7/8
326
15-3/8
Q
15-7/8
403
15-7/8
403
R
6-5/8
168
6-5/8
168
S
2-3/16
55
2-3/16
55
T
6
152
6
152
U
1
25
1
25
V
30-1/16
764
33-9/16
853
Figure 16.1 Appliance Dimensions - SL-550TR-E, SL-750TR-E
68
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
ELECTRICAL
ACCESS
J
O
N
P
Q
M
L
ØR
GAS LINE ACCESS
ØK
C
D
V
I
E
J
H
F
S
B
T
U
A
G
ELECTRICAL
ACCESS
SL-950TR-E
Location
Inches
Millimeters
A
48
1218
B
43
1092
C
39-1/16
993
D
23-9/16
599
E
41-9/16
1056
F
3-9/16
90
G
6-7/8
174
H
30-7/8
785
I
41-7/8
1063
J
43-15/16
1117
K
8
203
L
8-13/16
223
M
16-5/16
415
N
1/2
13
O
37-3/4
959
P
18-7/8
478
Q
15-11/16
406
R
6-5/8
168
S
2-3/16
55
T
6
152
U
1
25
V
37-9/16
955
Figure 16.2 Appliance Dimensions - SL-950TR-E
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
69
FOLIO DECORATIVE FRONT
C
D
B
E
F
A
G
550
750
950
A
B
C
D
E
F
G
in.
30-15/16
28-9/16
27-1/2
19-15/16
30-1/16
6-1/2
1-5/16
mm
785
728
699
505
763
164
34
in.
35-13/16
32-1/16
32-7/16
23-1/8
33-9/16
6-3/4
1-5/16
mm
909
814
823
587
852
172
34
in.
42-13/16
36-1/8
39-1/16
23-1/2
37-9/16
7-7/8
1-1/8
mm
1087
918
992
596
953
199
31
CHATEAU/HALSTON DECORATIVE FRONTS
C
D
Y
B
E
A
F
X
550
750
A
B
C
D
E
F
X
Y
in.
32-1/16
29-3/8
27-7/16
18-1/8
5-13/16
1-1/8
32-3/8
31-1/16
mm
814
746
696
461
147
29
822
791
in.
37-1/16
32-7/8
32-7/16
21-1/4
6-1/4
1-1/8
37-3/8
34-9/16
mm
941
834
823
539
158
29
949
878
Figure 16.3 Decorative Front Dimensions
70
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
CLEAN FACE DECORATIVE FRONTS
C
B
D
E
G
F
A
550
750
in.
A
B
C
D
E
F
G
30-13/16
23-5/16
26-9/16
18-11/16
25-7/16
3-1/2
4-9/16
mm
782
592
674
474
645
88
116
in.
35-13/16
26-13/16
31-1/2
22-3/16
28-15/16
3-1/2
4-9/16
mm
909
681
800
563
734
88
116
Figure 16.5 Appliance Dimensions - Clean Face Decorative Front
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
71
B. Vent Components Diagrams
Pipe
Effective
Height/Length
DVP Pipe (see chart)
Effective Length
Inches
Millimeters
DVP4
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
10-1/2 in.
(267 mm)
45 °
4-7/8 in.
(124 mm)
DVP48
48
1219
DVP6A
3 to 6
76 to 152
10-7/8 in.
(276 mm)
DVP12A
3 to 12
76 to 305
DVP45 (45º Elbow)
11-3/8 in.
(289 mm)
10 in.
(254 mm)
1 in.
(25 mm)
20-3/4 in.
(527 mm)
7-3/8 in.
(187 mm)
10 in.
(254 mm)
1-1/4 in. (32 mm)
9-1/4 in.
(235 mm)
Tab=1 in.
(25.4 mm)
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
Finished Height: 19-3/4 in./502 mm
UNIV-AS2 (Attic Insulation Shield)
DVP-FS (Ceiling Firestop)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
UP
5 in.
(127 mm)
1 in.
(25 mm)
8 in.
(203 mm)
14 in.
(356 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.6 DVP vent components
72
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
Trap1
Max
Effective
Length
12 in.
(305 mm)
Trap2
DVP-TRAP
Horizontal Termination Cap
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
DVP-HPC1
DVP-HPC2
Figure 16.7 DVP Vent Components
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
73
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(337 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(699 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(337 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
5 in.
(127 mm)
13-3/4 in.
(349 mm)
11-7/8 in.
(302 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-TRAPFL
Flashing
DVP-HSM-B
Extended Heat Shield
COOL-ADDM
Cap Shield
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DRC-RADIUS
Cap Shield
Figure 16.8 DVP Vent Components
74
5 in.
(127 mm)
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
B. Vent Components Diagrams (continued)
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
9 in.
(229 mm)
2-3/4 in.
(70 mm)
14 in.
(356 mm)
12-1/2 in.
(318 mm)
11-1/2 in.
(292 mm)
17-3/4 in.
(451 mm)
12-1/4 in.
(311 mm)
6 in.
152 mm
16 in.
(406 mm)
PVK-80
12 in.
(305 mm)
(For use with IPI and DSI appliances only.)
DVP-TB1
Basement Vent Cap
12 in.
305 mm
14 in.
(356 mm)
16-7/8 in.
(429 mm)
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
5-1/4 in.
(133 mm)
12 in.
(305 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
7-1/8 in.
(181 mm)
12-1/8 in.
(314 mm)
8-3/4 in.
(222 mm)
1 in.
(25 mm)
7-1/4 in.
(184 mm)
1-5/8 in.
(41 mm)
DVP-HPC
High Performance Cap
14 in.
(356 mm)
3/8 in. (10 mm)
1 in. (25 mm)
7-3/4 to 10-3/8 in.
(197 to 264 mm)
DVP-FBHT
FireBrickTermination Cap
Figure 16.9 DVP Vent Components
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
75
B. Vent Components Diagrams (continued)
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
8-3/8 in.
213 mm
5-1/2 in.
140 mm
87°
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
DVP-HRC-SS
HORIZONTAL TERMINATION CAP
Figure 16.6 DVP vent components
WARNING
Fire Risk.
• When using SLP-HRC-SS termination cap
on top vented fireplaces, a one foot minimum
vertical vent section is required before installing
first elbow.
• When using DVP-TB1 termination cap on top vented
fireplaces, a three foot minimum vertical vent section is required
before installing first elbow.
8-1/8 in.
(206 mm)
13 in.
(330 mm)
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in.
140 mm
87°
8-3/8 in.
213 mm
3°
15 in.
(381 mm)
10-1/2 in.
267 mm
10-7/8 in.
276 mm
SLP-HRC-SS
HORIZONTAL TERMINATION CAP
DVP-TB1
SLP90
DVP-TB1
SL-2DVP
ASSEMBLY
Figure 16.10 SLP Series Vent Components
76
DVP-TB1
HORIZONTAL TERMINATION CAP
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
6-1/2 in.
165 mm
9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
SLP45
45° Elbow
6-5/8 in.
168 mm
9-7/8 in.
251 mm
SLP90
90° Elbow
Effective
Height/
Length
Effective Height/Length
SLP PIPE
10-7/8 in.
276 mm
Pipe
inches
mm
SLP4
4
102
SLP6
6
152
SLP12
12
305
SLP24
24
610
SLP36
36
914
SLP48
48
1219
SLP6A
2-6
51 - 152
SLP12A
2 - 12
51 - 305
SLP-FLEX-2
24
610
SLP-FLEX-3
36
914
SLP-FLEX-5
60
1524
SLP-FLEX-10
120
3048
EFFECTIVE HEIGHT/
LENGTH
SLP-FLEX-PIPE
1-1/2 in.
38 mm
8-7/8 in.
225 mm
SLP-HVS
Horizontal Pipe
Support
8-11/16 in.
220 mm
12 in.
305 mm
8-11/16 in.
220 mm
1-1/2 in.
38 mm
12 in.
305 mm
5-1/2 in.
146 mm
SLP-WS
Wall Shield Firestop
SLP-FS
Ceiling Firestop
Figure 16.11 SLP Series Vent Components
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
77
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm)
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a
DVP-HSM-B will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Max
Effective
Length
12 in.
(305 mm)
Trap1
Trap2
SLP-TRAP
Horizontal Termination Cap
6-11/16 in.
(169 mm)
3-15/16 in.
(101 mm)
Maximum
Effective Length
3-1/8 in.
4-3/4 in.
79 mm
121 mm
5-1/4 in.
9-1/4 in.
133 mm
235 mm
4-3/16 in.
106 mm
6-3/8 in.
163 mm
3-15/16 in.
(101 mm)
3-13/16 in.
(97 mm)
Minimum
Effective Length
4-5/8 in.
117 mm
4 in.
102 mm
5-1/16 in.
(128 mm)
8 in.
(203 mm)
5-1/16 in.
128 mm
8-1/8 in.
206 mm
DVP-2SL
Adapter
SL-2DVP
Adapter
2-3/4 in.
(70 mm)
14-7/16 in.
367 mm
9 in.
(229 mm)
12-1/2 in.
(318 mm)
11-1/2 in.
(292 mm)
2-5/16 in.
59 mm
14-7/16 in.
367 mm
12-1/4 in.
(311 mm)
16 in.
(406 mm)
SLP-WT-BK
Wall Thimble-Black
PVK-80
(For use with IPI and DSI appliances only.)
26 in.
660 mm
DVP-FBHT
SLP90
SL-2DVP
DVP-HSM-B
Extended Heat Shield
Figure 16.12 SLP Series Vent Components
78
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
DVP-FBHT
B. Vent Components Diagrams (continued)
13 in.
330 mm
14 in.
356 mm
1-5/16 in.
34 mm
13 in.
330 mm
10-9/16 in.
269 mm
SLP-DCF-BK
Ceiling Firestop
Black
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
12 in.
305 mm
14-1/16 in.
357 mm
12-1/2 in.
318 mm
14 in.
356 mm
7-1/2 in.
192 mm
10-3/4 in.
273 mm
SLP-FLEX-TRAP
Horizontal
Termination Kit
10-11/16 in.
271mm
28-1/2 in.
724 mm
SLP-TVHW
Vertical
Termination Cap
1 in.
(25 mm)
7-1/4 in.
(184 mm)
14 in.
(356 mm)
3/8 in. (10 mm)
1 in. (25 mm)
13-1/2 in.
343 mm
7-3/4 to 10-3/8 in.
(197 to 264 mm)
SLK-SNKD
Snorkel
Termination Cap
DVP-FBHT
Horizontal
Termination Cap
Figure 16.13 SLP Series Vent Components
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
79
B. Vent Components Diagrams (continued)
Optional Wire Harness
13-5/8 IN.
346 mm
DESCRIPTION
12-1/2 IN.
318 mm
PART NUMBER
10 ft. PV Wire Harness
PVI-WH10
20 ft. PV Wire Harness
PVI-WH20
40 ft. PV Wire Harness
PVI-WH40
60 ft. PV Wire Harness
PVI-WH60
80 ft. PV Wire Harness
PVI-WH80
100 ft. PV Wire Harness
PVI-WH100
Note: Wire harnesses required to power the PVI-SLP
connect to the appliance and are ordered separately
from PVI-SLP. Contact your dealer to order.
20-3/4 IN.
527 mm
Note: Use only approved termination caps with the
PVI-SLP. See instructions included with PVI-SLP kit.
PVI-SLP
Power Vent Inline
16 IN.
406 mm
4-1/2 IN.
114 mm
15 IN.
(381 mm)
9-3/16 IN.
(233 mm)
13-5/8 IN.
(346 mm)
12-1/2 IN.
(318 mm)
16-11/16 IN.
424 mm
16-11/16 IN.
(424 mm)
SLP-LPC
SLP Low Profile Cap
COAXIAL to COLINEAR VENTING
LINK-DV30B
Flex Liner Kit
DVP-2SL
Adapter
DV-46DVA-GCL
Coaxial/Colinear Appliance Connector
Figure 16.14 Vent Components
80
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
SL-550TR-E
C.
Service
Parts
Service
Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
32” Gas Fireplace - DV
Log Set Assembly
2
3
4 1
5
6
7
8
10
9
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-550-E
1
Log 1
SRV2115-701
2
Log 2
SRV2115-702
3
Log 3
SRV2115-703
4
Log 4
SRV2115-704
5
Log 5
SRV2115-705
6
Burner NG, LP
2115-007
Y
Y
7
Valve Assembly
8
Grate Assembly
Refer to Valve page
2115-015
9
Glass Door Assembly
GLA-550TR
Y
10
Junction Box
4021-013
Y
Exhaust BafÀe
550-155
Exhaust Restrictor
530-299
Gasket Assembly
2115-080
Contains Burner neck, shutter bracket, vent, seal cap, valve plate,
and air passage gaskets
Pkg of 2
Glass Latch Assembly
33858/2
Lava Rock
4021-297
Mineral Wool
050-721
Touch Up Paint
TUP-GBK-12
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Y
3/15
81
SL-750TR-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
36” Gas Fireplace - DV
Log Set Assembly
2
4 1
3
5
6
7
8
10
9
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-750-E
1
Log 1
SRV2118-701
2
Log 2
SRV2118-702
3
Log 3
SRV2118-703
4
Log 4
SRV2118-704
5
Log 5
SRV2118-705
6
Burner NG, LP
7
Valve Assembly
8
Grate Assembly
2118-015
9
Glass Door Assembly
GLA-750TR
Y
Y
10
2118-007
Y
Y
Refer to Valve page
Junction Box
4021-013
Exhaust BafÀe
550-155
Exhaust Restrictor
530-299
Gasket Assembly
2118-080
Contains Burner neck, shutter bracket, vent, seal cap, valve
plate, and air passage gaskets
Pkg of 2
Glass Latch Assembly
Lava Rock
4021-297
Mineral Wool
050-721
Touch Up Paint
TUP-GBK-12
Additional service part numbers appear on following page.
82
33858/2
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Y
3/15
SL-550TR-E, SL-750TR-E
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
STANDING PILOT CONVERSION KITS
Conversion Kit NG
SL-550TR-E
Conversion Kit LP
Conversion Kit NG
SL-750TR-E
Conversion Kit LP
NGKS-550TR-E
Y
LPKS-550TR-E
Y
NGKS-750TR-E
Y
LPKS-750TR-E
Y
Pilot Ori¿ce NG
2103-116
Y
Pilot Ori¿ce LP
2103-117
Y
Regulator NG
230-1570
Y
Regulator LP
230-1520
Y
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
83
SL-550TR-E, SL-750TR-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
#7 Valve Assembly
7.1
7.2
7.3
7.10
7.9
7.4
7.8
7.5
7.7
7.6
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
7.1
COMMENTS
PART NUMBER
Pilot Assembly NG
2103-010
Y
Pilot Assembly LP
2103-011
Y
Pilot Tube
SRV485-301
Y
Thermocouple
2103-511
Y
Thermopile
2103-512
Y
7.2
3-Hole Grommet
2118-420
7.3
Shutter Bracket Assembly
2118-121
Y
7.4
Flex Tube Assembly
7000-156
Y
7.5
Thermostat Wire Assembly
2045-024
Y
Valve NG
230-0710
Y
Valve LP
230-0720
Y
7.6
7.7
Piezo Ignitor
291-513
Y
7.8
Flex Ball Valve Assembly
302-320A
Y
7.9
Valve Bracket
2118-104
Ori¿ce NG (#44C)
582-844
Y
Ori¿ce LP (#55C)
582-855
Y
Conversion Kit NG
NGKS-550TR-E
Y
Conversion Kit LP
LPKS-550TR-E
Y
Pilot Ori¿ce NG
2103-116
Y
Pilot Ori¿ce LP
2103-117
Y
Regulator NG
230-1570
Y
Regulator LP
230-1520
Y
7.10
84
DESCRIPTION
Stocked
at Depot
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
SL-550TR-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
32” Gas Fireplace - DV
Log Set Assembly
2
3
4 1
5
6
7
8
10
9
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-550-E
1
Log 1
SRV2115-701
2
Log 2
SRV2115-702
3
Log 3
SRV2115-703
4
Log 4
SRV2115-704
5
Log 5
SRV2115-705
6
Burner NG, LP
2115-007
Y
Y
7
Valve Assembly
8
Grate Assembly
Refer to Valve page
2115-015
9
Glass Door Assembly
GLA-550TR
Y
10
Junction Box
4021-013
Y
Exhaust BafÀe
550-155
Exhaust Restrictor
530-299
Gasket Assembly
2115-080
Contains Burner neck, shutter bracket, vent, seal cap, valve plate,
and air passage gaskets
Pkg of 2
Glass Latch Assembly
33858/2
Lava Rock
4021-297
Mineral Wool
050-721
Touch Up Paint
TUP-GBK-12
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Y
3/15
85
SL-550TR-IPI-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
32” Gas Fireplace - DV
6
Log Set Assembly
2
3
4 1
5
7
8
9
11
10
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Set Assembly
LOGS-550-E
1
Log 1
SRV2115-701
2
Log 2
SRV2115-702
3
Log 3
SRV2115-703
4
Log 4
SRV2115-704
5
Log 5
SRV2115-705
6
Drywall Lip
2115-119
7
Burner NG, LP
2115-007
8
Valve Assembly
Y
Y
Refer to Valve page
9
Grate Assembly
2115-015
10
Glass Door Assembly
GLA-550TR
Y
11
Junction Box
4021-013
Y
Exhaust BafÀe
550-155
Exhaust Restrictor
530-299
Gasket Assembly
2115-080
Contains Burner neck, shutter bracket, vent, seal cap, valve plate,
and air passage gaskets
Pkg of 2
Glass Latch Assembly
4021-297
Mineral Wool
050-721
Touch Up Paint
TUP-GBK-12
Additional service part numbers appear on following page.
86
33858/2
Lava Rock
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Y
3/15
SL-750TR-IPI-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
36” Gas Fireplace - DV
6
Log Set Assembly
2
3
4 1
5
7
8
9
11
10
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
Log Set Assembly
LOGS-750-E
1
Log 1
SRV2118-701
2
Log 2
SRV2118-702
3
Log 3
SRV2118-703
4
Log 4
SRV2118-704
5
Log 5
SRV2118-705
6
Drywall Lip
2118-119
7
Burner NG, LP
2118-007
Y
Y
8
Valve Assembly
9
Grate Assembly
Refer to Valve page
2118-015
10
Glass Door Assembly
GLA-750TR
Y
11
Junction Box
4021-013
Y
Exhaust BafÀe
550-155
Exhaust Restrictor
530-299
Gasket Assembly
2115-080
Contains Burner neck, shutter bracket, vent, seal cap, valve plate,
and air passage gaskets
Pkg of 2
Glass Latch Assembly
33858/2
Lava Rock
4021-297
Mineral Wool
050-721
Touch Up Paint
TUP-GBK-12
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Y
3/15
87
SL-950TR-IPI-E
Service Parts
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
42” Gas Fireplace - DV
6
Log Set Assembly
2
3
4 1
5
7
11
10
9
8
12
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
13
PART NUMBER
Log Set Assembly
LOGS-950-E
1
Log 1
SRV2121-701
2
Log 2
SRV2121-702
3
Log 3
SRV2118-703
4
Log 4
SRV2121-704
5
Log 5
SRV2121-705
6
Non Comb Support
2122-119
7
Burner NG, LP
2121-007
8
Valve Assembly
9
Burner Skirt
2121-142
10
Grate Assembly
2121-015
11
Glass Door Assembly
GLA-950TR
Y
12
Junction Box
4021-013
Y
13
Non Combustible Board
560-401
Exhaust BafÀe
550-155
Exhaust Restrictor
530-299
Y
Y
Refer to Valve Page
Gasket Assembly
2121-080
Contains Burner neck, shutter bracket, vent, seal cap, valve
plate, and air passage gaskets
Pkg of 2
Glass Latch Assembly
Lava Rock
4021-297
Mineral Wool
050-721
Non Combustible Board
560-401
Touch Up Paint
TUP-GBK-12
Additional service part numbers appear on following page.
88
33858/2
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
Y
3/15
Service Parts
SL-550-IPI-E, SL-750-IPI-E, SL-950-IPI-E
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
IPI CONVERSION KITS
NGK-550IPIE
Y
LPK-550IPIE
Y
NGK-750IPIE
Y
LPK-750IPIE
Y
NGK-950IPIE
Y
LPK-950IPIE
Y
Pilot Ori¿ce NG
593-528
Y
Pilot Ori¿ce LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
Conversion Kit NG
SL-550TR-IPI-E
Conversion Kit LP
Conversion Kit NG
SL-750TR-IPI-E
Conversion Kit LP
Conversion Kit NG
SL-950TR-IPI-E
Conversion Kit LP
Additional service part numbers appear on following page.
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
89
Service Parts
SL-550-IPI-E, SL-750-IPI-E, SL-950-IPI-E
Beginning Manufacturing Date: June 2007
Ending Manufacturing Date: Active
#8 Valve Assembly
8.1
8.12
8.2
8.10
8.11
8.3
8.9
8.8
8.13
8.4
8.6
8.5
8.7
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
8.1
DESCRIPTION
COMMENTS
PART NUMBER
Pilot Assembly NG
2090-012
Y
Pilot Assembly LP
2090-013
Y
SRV485-301
Y
Pilot Tube
8.2
Shutter Bracket Assembly
2118-121
Y
8.3
Battery Pack
593-594A
Y
8.4
Flex Tube Assembly
7000-156
Y
8.5
3 Volt Transformer
593-593A
Y
8.6
Module Wire Assembly
593-590A
Y
8.7
Thermostat Wire Assembly
2118-170
Y
8.8
Module
593-592
Y
Valve NG
750-500
Y
Valve LP
750-501
Y
8.10
Flex Ball Valve Assembly
302-320A
Y
8.11
Valve Bracket
2118-104
8.12
3-Hole Grommet
2118-420
Ori¿ce NG (#44)
582-844
Y
Ori¿ce LP (#55)
582-855
Y
Conversion Kit NG
NGK-550IPIE
Y
Conversion Kit LP
LPK-550IPIE
Y
Pilot Ori¿ce NG
593-528
Y
Pilot Ori¿ce LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
8.9
8.13
90
Stocked
at Depot
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th St, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5613487, 5647340, 5890485,
5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269,
7258116, 7470729, 8147240 or other U.S. and foreign patents pending.
2000-945C
Printed in U.S.A. - Copyright 2015
Heat & Glo • SL-550 / 750 / 950TR-E • 2118-900 Rev. AC • 3/15
91