advertisement
Installation Manual
Models 99087, 99088, 99089, 99090, 99091
Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca Fans
MA004-01 • 07/24/13
BEFORE YOU BEGIN
Read entire installation instructions carefully before beginning installation and save these instructions.
1.888.830.1326
Switch
Housing
Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s switch housing. Begin on page 3 where you will choose the type of switch housing that most closely resembles the one on your fan. From there, you will be directed to the set of assembly instructions that are appropriate for installing the light kit to your fan.
READ AND SAVE THESE INSTRUCTIONS
This product conforms to UL Standard 507.
WARNINGS w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs. (31.8 kg) and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
CAUTIONS c.1 - All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
2
MA004-01 • 07/24/13
Turn
Pow er
OFF
1.888.830.1326
WHICH ASSEMBLY METHOD WILL I USE?
Choose one of the four images below that most closely resembles the switch housing on your fan; then follow the instructions under the image.
Cap
Screw
Switch
Housing
Cap
If your fan’s switch housing cap resembles this one, remove the cap screws with a Phillips head screwdriver.
Then follow the TYPE-A ASSEMBLY
INSTRUCTIONS on pages 4-5.
Switch
Housing
Screw
Switch
Housing
Cap
If your fan’s switch housing cap resembles this one, remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver.
Remove the two cap screws from the inside of the switch housing. Reinstall the switch housing. Tighten the switch housing screws. Then follow the TYPE-A
ASSEMBLY INSTRUCTIONS on pages 4-5.
Switch
Housing
Screw
Plug
Button
Plug
Button
Switch
Housing
Screw
If your fan’s switch housing cap resembles this one, remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver. Remove the plug button.
Then follow the TYPE-B ASSEMBLY
INSTRUCTIONS on pages 6-7.
If your fan’s switch housing cap resembles this one, remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver.
Remove the plug button using a standard screwdriver. Then follow the TYPE-C
ASSEMBLY INSTRUCTIONS on pages 8-9.
3
MA004-01 • 07/24/13
1
Light Kit
Screw
TYPE-A ASSEMBLY INSTRUCTIONS
2
Switch
Housing
Wire
Connector
1.888.830.1326
3
Remove the pre-installed light kit screws and replace them with the longer light kit screws provided.
If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness.
4
Light Kit
Screw
Using the single pin connectors, connect the black or blue wire from the fan to the black wire from the light kit. Connect the white wire from the fan to the white wire from the light kit.
4
MA004-01 • 07/24/13
Lift the light kit up to meet the lower switch housing. Align the light kit screws with the threaded holes in the lower switch housing. Tighten screws securely.
Do not allow the light kit to hang only by the wire connections!
1.888.830.1326
5
TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)
6
Socket
Shade
(sold separately)
Socket
Ring
Socket
Ring Tool
Installing the shades (sold separately)-
Remove the socket rings from the sockets. Install each shade onto a socket.
Install the socket rings onto the sockets by turning them clockwise using the socket ring tool.
Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage.
7 8
Installing the pull chain pendant -
Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
5
MA004-01 • 07/24/13
Turn
Pow er
ON
Turn on power. Your installation is complete!
1
TYPE-B ASSEMBLY INSTRUCTIONS
2
1.888.830.1326
Switch
Housing
Wire
Connector
3
If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness.
4
Feed the wires through the center hole in the switch housing, the washer, and the nut.
Push the center hole in the gasket over the threaded rod of the light kit. Then install the switch housing by twisting clockwise onto the threaded rod. Install the washer and nut onto threaded rod and tighten securely.
Using the single pin connectors, connect the black or blue wire from the fan to the black wire from the light kit. Connect the white wire from the fan to the white wire from the light kit.
6
Switch
Housing
Screw
Lift the light kit assembly up so that the screw holes in the lower switch housing line up with the holes in the upper switch housing. Install the switch housing screws and tighten securely.
Do not allow the light kit to hang only by the wire connections!
MA004-01 • 07/24/13
1.888.830.1326
5
TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)
6
Socket
Shade
(sold separately)
Socket
Ring
Socket
Ring Tool
Installing the shades (sold separately)-
Remove the socket rings from the sockets. Install each shade onto a socket.
Install the socket rings onto the sockets by turning them clockwise using the socket ring tool.
Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage.
7 8
Installing the pull chain pendant -
Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
7
MA004-01 • 07/24/13
Turn
Pow er
ON
Turn on power. Your installation is complete!
1
TYPE-C ASSEMBLY INSTRUCTIONS
2
Washer and Nut
Threaded
Rod
1.888.830.1326
Switch
Housing
Wire
Connector
3
If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness.
Feed the wires through the switch housing cap, washer, and nut. Then install the switch housing cap by twisting clockwise onto the threaded rod, making sure the gasket stays in line with the top of the light kit. Install the washer and nut onto threaded rod and tighten securely.
4
Upper
Switch
Housing
Using the single pin connectors, connect the black or blue wire from the fan to the black wire from the light kit. Connect the white wire from the fan to the white wire from the light kit.
8
Lift the light kit assembly up so that the screw holes in the lower switch housing line up with the holes in the upper switch housing. Install the switch housing screws and tighten securely.
Do not allow the light kit to hang only by the wire connections!
MA004-01 • 07/24/13
1.888.830.1326
5
TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)
6
Socket
Shade
(sold separately)
Socket
Ring
Socket
Ring Tool
Installing the shades (sold separately)-
Remove the socket rings from the sockets. Install each shade onto a socket.
Install the socket rings onto the sockets by turning them clockwise using the socket ring tool.
Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage.
7 8
Installing the pull chain pendant -
Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
9
MA004-01 • 07/24/13
Turn
Pow er
ON
Turn on power. Your installation is complete!
TROUBLESHOOTING
Lights don’t come on.
• Make sure that the bulbs are properly installed.
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power wires are correctly connected to the ceiling and the light kit.
1.888.830.1326
ONE YEAR WARRANTY
This product is warranted to the original purchaser by Casablanca Fan Company/
Hunter Fan Company against defects in material and workmanship for one (1) year from date of purchase. During the warranty period, we will repair or, at our option, replace a defective product at no charge. For information on how to obtain service, contact the Casablanca/Hunter Service Department by calling our tollfree number at 888-830-1326. Damage to the product caused by mishandling, improper installation or modification is not covered by this warranty. This warranty is given in lieu of all other warranties expressed or implied. Some states do not allow limitations of time on an implied warranty, therefore the above limitations may not apply in every case. This warranty states specific legal rights which may vary from state to state.
If you have problems installing or operating your light kit, do not return this product to the dealer. Call our Consumer Affairs Hotline.
888-830-1326
Monday through Friday
8:00 am to 4:30 pm Central
10
MA004-01 • 07/24/13
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement