Sharp AR-FX4 Service manual

SERVICE MANUAL
CODE: 00ZAR275//A1E
DIGITAL LASER COPIER/
PRINTER
MODEL
AR-235
AR-275
CONTENTS
[1] NOTE FOR SERVICING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[3] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[4] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[5] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[6] EXTERNAL VIEW AND INTERNAL STRUCTURE . . . . . . . . . . . . 6-1
[7] ADJUSTMENTS, SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[8] SIMULATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[9] TROUBLE CODE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[10] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[11] OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CAUTION
This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard and IEC825. This means that this
machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eye’s retina, there is the danger of spot
damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts.
2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical
system.
4) The middle frame contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
Warning!
This product is a class A product.
If it is operated in households, offices or similar surroundings, it can produce radio interferences at other
appliances, so that the user has to take adequate countermeasures.
VAROITUS!
CLASS 1 LASER PRODUCT
LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.
LASER KLASSE 1
LUOKAN 1 LASERLAITE
VARNING
OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I
DENNA BRUKSANVISNING SPECIFICERATS, KAN
ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG
LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN
FÖR LASERKLASS 1.
KLASS 1 LASERAPPARAT
CAUTION
INVISIBLE LASER RADIATION,
WHEN OPEN AND INTERLOCKS DEFEATED. AVOID
EXPOSURE TO BEAM.
VARO !
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT
DEM STRAHL AUSSETZEN.
VARNING !
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ
KATSO SÄTEESEEN.
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ
STRÅLEN. – STRÅLEN ÄR FARLIG.
ADVARSEL
USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER UDE AF
FUNKTION. UNDGÅ UDSAETTELSE FOR
STRÅLNING.
Laserstrahl
LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES.
CAUTION INVISIBLE
AVOID EXPOSURE TO BEAM.
ADVERSEL USYNLIG
UNNGÅ EKSPONERING FOR STRÅLEN.
LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET UND
LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR
VORSICHT UNSICHTBARE
VARNING OSYNLIG
SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
URKOPPLAD. BETRAKTA EJ STRÅLEN. – STRÅLEN ÄR FARLIG.
LASERSTRÅLNING VED ÅBNING, NÅR SIKKERHEDSBRYDERE ER
JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE
ADVARSEL USYNLIG
UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.
VARO! AVATTAESSA
LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.
CLASS 1
LASER PRODUCT
LASER KLASSE 1
LASER WAVE – LENGTH : 795 ± 15 mm
Pulse times : 0.481 ms/6 mm
Out put power : 5 mW
Disconnect the AC cord before servicing the unit.
CONTENTS
[1] NOTE FOR SERVICING
1. Warning for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
3. Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
A. Key position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
2. Precautions for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
B. LCD panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
3. Note for installing site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
4. Motor, Solenoid, Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
[2] SYSTEM CONFIGURATION
1. Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
A. Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2. System outline (Options) . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
[3] SPECIFICATIONS
1. Basic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
2. Operation specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
A. Common operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
B. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3. Engine specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
5. Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6. PWB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
7. Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
[7] ADJUSTMENTS, SETTING
1. List of adjustment items . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
2. Copier adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
A. Process section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
B. Mechanism section . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
C. Image density (exposure) adjustment . . . . . . . . . . . . . .7-9
[8] SIMULATION
A. Operation and display section . . . . . . . . . . . . . . . . . . . 3-2
1. Operating procedures and operations . . . . . . . . . . . . . . . .8-1
B. Paper feed, transport, paper exit section . . . . . . . . . . . 3-2
A. Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
C. Optical (Image scanning) section . . . . . . . . . . . . . . . . . 3-3
B. Simulation kinds and valid key functions . . . . . . . . . . . .8-1
D. Scanner (exposure) section . . . . . . . . . . . . . . . . . . . . . 3-3
C. Simulation operation and procedure basic pattern . . . .8-2
E. Image process section . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
2. Simulation code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3
F. Fusing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3. Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5
G. DRIVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
4. Safety and environmental protection standards. . . . . . . . . 3-4
5. Environment conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
[4] CONSUMABLE PARTS
1. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
A. SEC/LAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
B. SECL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
C. Europe affiliates/East Europe/SEEG/SUK/SCA/
SCNZ/SEA/SEES/SEZ/SEIS/SEB/SEN/SEF/SMEF/
Russia/Middle East/Africa/CIS . . . . . . . . . . . . . . . . . . . 4-3
[9] TROUBLE CODE LIST
1. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
2. Self diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
[10] DISASSEMBLY, ASSEMBLY AND MAINTENANCE
1. Maintenance table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
2. Counter clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1
3. List of disassembly and assembly . . . . . . . . . . . . . . . . . .10-1
4. Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2
A. Process unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2
D. Special country/Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
B. Developing section . . . . . . . . . . . . . . . . . . . . . . . . . . .10-3
E. Asia affiliates /Asia agent/STCL/SRH/SRS/SRSSC/
SBI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
C. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-4
2. Production number identification . . . . . . . . . . . . . . . . . . . . 4-6
E. Side door unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-10
3. Environment conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
F. 1st paper exit unit . . . . . . . . . . . . . . . . . . . . . . . . . . .10-10
A. Ambient conditions for transporting . . . . . . . . . . . . . . . 4-6
G. Laser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-12
B. Ambient storage conditions (sealed) . . . . . . . . . . . . . . 4-6
H. Power unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-13
C. Operating ambient conditions. . . . . . . . . . . . . . . . . . . . 4-6
I. PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-13
4. Life (packed conditions) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
J. Ozone filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-15
[5] UNPACKING AND INSTALLATION
D. Paper feed section. . . . . . . . . . . . . . . . . . . . . . . . . . . .10-6
[11] OTHERS
1. Removal of protective material and fixing screw . . . . . . . . 5-1
1. Flash ROM version up procedure . . . . . . . . . . . . . . . . . . .11-1
2. Removal and storage of fixing pin . . . . . . . . . . . . . . . . . . . 5-1
A. Program download procedure
(Main body program, FAX program) . . . . . . . . . . . . . .11-1
3. Developer cartridge installation . . . . . . . . . . . . . . . . . . . . . 5-1
4. Toner cartridge installation . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5. Toner concentration sensor level adjustment. . . . . . . . . . . 5-2
6. Paper size selection for paper feed tray . . . . . . . . . . . . . . 5-2
[6] EXTERNAL VIEW AND INTERNAL STRUCTURE
1. External view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
2. Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
2. User programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2
3. E-MAIL STATUS/E-MAIL ALERTS . . . . . . . . . . . . . . . . . .11-3
A. Basic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3
B. Main body specifications . . . . . . . . . . . . . . . . . . . . . . .11-3
C. Printer controller specifications . . . . . . . . . . . . . . . . . .11-3
D. Handling of transmission data . . . . . . . . . . . . . . . . . . .11-3
[1] NOTE FOR SERVICING
6) Do not leave the machine with the cabinet disassembled.
This Service Manual uses some photographs to assure safe operation.
This Service Manual uses some photographs to assure safe operation.
Please understand the meanings of photographs before servicing.
WARNING: If this WARNING should be ignored, a serious danger
to life or a serious injury would be resulted.
CAUTION: If this CAUTION should be ignored, an injury or a
damage to properties would be resulted.
Do not allow any person other than a serviceman to touch inside
the machine. It may cause an electric shock, a burn, or an injury.
7) When servicing, do not breathe toner, developer, and ink excessively. Do not get them in the eyes.
If toner, developer, or ink enters you eyes, wash it away with water
immediately, and consult a doctor if necessary.
8) The machine has got sharp edges inside. Be careful not to damage fingers when servicing.
9) Do not throw toner or a toner cartridge in a fire. Otherwise, toner
may pop and burn you.
1. Warning for servicing
1) Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Avoid complex wiring, which may lead to a fire or an electric shock.
It may cause a fire or an electric shock.
2) If there is any abnormality such as a smoke or an abnormal smell,
interrupt the job and disconnect the power plug.
10) When replacing the lithium battery of the PWB, use a specified one
only.
If a battery of different specification is used, it may be broken,
causing breakdown or malfunction of the machine.
11) When carrying a unit with PWB or electronic parts installed to it, be
sure to put it in an anti-static-electricity bag.
It may cause a breakdown or malfunctions.
It may cause a fire or an electric shock.
3) Be sure to connect the grounding wire. If an electric leakage
occurs without grounding, a fire or an electric shock may be the
result.
To protect the machine and the power unit from lightening, grounding must be made.
4) When connecting the grounding wire, never connect it to the following points.
It may cause an explosion, a fire or an electric shock.
• Gas tube
• Lightning conductor
3. Note for installing site
Do not install the machine at the following sites.
1) Place of high temperature, high humidity, low temperature, low
humidity, place under an extreme change in temperature and
humidity.
Paper may get damp and form dews inside the machine, causing
paper jam or copy dirt.
For operating and storing conditions, refer to the specifications
described later.
2) Place of much vibrations
• A water pipe or a water faucet, which is not recognized as a
grounding object by the authorities.
• Grounding wire for telephone line
It may cause a breakdown.
3) Poorly ventilated place
An electro-static type copier will produce ozone inside it.
5) Do not damage, brake, or work the power cord.
Do not put heavy objects on the power cable. Do not bend it forcibly or do not pull it extremely.
It may cause a fire or an electric shock.
6) Keep the power cable away from a heat source.
The quantity of ozone produced is designed to a low level so as
not to affect human bodies. However, continuous use of such a
machine may produce a smell of ozone. Install the machine in a
well ventilated place, and ventilate occasionally.
4) Place of direct sunlight.
Do not insert the power plug with dust on it into a power outlet.
It may cause a fire or an electric shock.
7) Do not put a receptacle with water in it or a metal piece which may
drop inside the machine.
It may cause a fire or an electric shock.
8) With wet or oily hands, do not touch the power plug, do not insert
the telephone line jack, do not operate the machine, or do not perform servicing.
It may cause an electric shock.
Plastic parts and ink may be deformed, discolored, or may undergo
qualitative change.
It may cause a breakdown or copy dirt.
5) Place which is full of organic gases such as ammonium
The organic photoconductor (OPC) drum used in the machine may
undergo qualitative change due to organic gases such as ammonium.
Installation of this machine near a diazo-type copier may result in
dirt copy.
6) Place of much dust
2. Precautions for servicing
1) When servicing, disconnect the power plug, the printer cable, the
network cable, and the telephone line from the machine, except
when performing the communication test, etc.
It may cause an injury or an electric shock.
2) There is a high temperature area inside the machine. Use an
extreme care when servicing.
It may cause a burn.
3) There is a high voltage section inside the machine which may
cause an electric shock . Be careful when servicing.
4) Do not disassemble the laser unit. Do not insert a reflective material such as a screwdriver in the laser beam path.
It may damage eyes by reflection of laser beams.
When dusts enter the machine, it may cause a breakdown or copy
dirt.
7) Place near a wall
Some machine require intake and exhaust of air.
If intake and exhaust of air are not properly performed, copy dirt or
a breakdown may be resulted.
8) Unstable or slant surface
If the machine drops or fall down, it may cause an injury or a breakdown.
If there are optional paper desk and the copier desk specified, it is
recommendable to use them.
When using the optional desk, be sure to fix the adjuster and lock
the casters.
5) When servicing with the machine operating, be careful not to
squeeze you hands by the chain, the belt, the gear, and other driving sections.
AR-235/275 NOTE FOR SERVICING - 1
AR-235/275 SYSTEM CONFIGURATION - 1
TRCL; Vertical transport
roller clutch 2
PPD1 ; Paper Pass Detector
PAP1 ; Paper Empty
LUD1 ; Lift Up Detector
CSS1 ; Casette Detector
DRS1 ; Door Detector
PCL1 ; Pick Up Clutch
LUM1 ; Lift Up Motor
OP-UP cassette
OP interface PWB
CN140
CN129
CN103
CN104
Pout Gate
Solenoid
CN131
CN126
CN118
2nd POUT COVER
SENSOR
CN28
Pout 2 Ssensor
HPSIZE2: Handpaper Size Sensor 2
HPWS: Handpaper Width Sensor
HPSOL: Handpaper PickUp Solenoid
PAP2 ; Paper Empty
LUD2 ; Lift Up Detector
CSS2 ; Casette Detector
Fuser-Lamp
THERMISTER
Fuser Unit
PSRSOL: Paper Stop Roller Sol.
LUM2 ; Lift Up Motor
LUM1H: Lift Up Motor
PCL1H: PickUp Cluth
CSS1H: Cassette Detector
PCL2 ; Pick Up Clutch
DRS2 ; Door Detector
HPSIZE1: Handpaper Size Sensor 1
PPD2 ; Paper Pass Detector
HPTRAY2: HandpaperTRAY Sensor 2
HPTRAY1: HandpaperTRAY Sensor 1
HPIN: Handpaper IN Sensor
HPEMPTY: HandpaperEmpty sensor
Manual feed cassette
Main body paper feed load
Paper Feed Motor
OP interface PWB
OP-LO cassette
Paper Feed Motor
Multi-step cassette unit (Optional)
TRCLH: Vertical transport
roller clutch
PCL2H ; Pick Up Clutch
LUM2H ; Lift Up Motor
CSS2H ; Casette Detector
DRS2H ; Door Detector
PPD2H ; Paper Pass Detector
PAP2H ; Paper Empty
LUD2H ; Lift Up Detector
2nd cassette unit (Optional)
Sol
Drum Initial
PCS1H ; Pick Up Solenoid
Sensor
Paper Remove
PPD1H(PIN):Paper IN
Sensor
Paper Out
Duplex
Duplex-Motor
LUD1H ; Lift Up Detector
PAP1H ; Paper Empty
Main body cassette unit
Shifter-Motor
Fuser Cooling Fan 22
Sensor
HP
Shifter
SPF-DupSO
Pout Sensor
SPF-pressure
release SOL
Fuser Cooling Fan 1
SPF-Motor
CN123
CN115
MAIN-Motor
Copy-Lamp
Heater
Defog
AB
FAX-OP-PWB
OPERATION PANEL
CN132
INCH
Coin
Vender
COPY-OP-PWB
LCD
CN108
CCD-PWB
IMC PWB
Sensor
Mirror HP
Paper Size Sensor
Cn130
(AB Area ONLY)
SPF-CON-PWB
Paper Full Sensor
CN113
Sensor
CN125
(INCH Area ONLY)
L2
CN139
Cover
CN136
L1
CN134
Scanner
CN111
SPF Paper Empty
D-Sub 25pin
InterLock
Switch
APC-PWB
LSU-PWB
D-Sub 9pin
MCU-PWB
CN117
D-Sub 15pin
BD-Sensor
BD-PWB
HVU
Power Unit
Power Supply
(CE Only)
Reactor
PS-SW
PS Cooling Fan
(Japan Only)
Defog Heater
Rear edge plate HP sensor
Paper Size Detector
Rear edge plate
drive motor
Transport select gate right
solenoid
Rear edge plate drive
solenoid
Paper position sensor
Tray position sensor Upper
Lift-up drive control sensor
(Optional)
PCL PWB
(Optional)
FIN main motor
Upper alignment plate drive
solenoid
Tray lift-up motor Transport select gate right
solenoid 2
Tray off-set motor Shutter drive solenoid
Tray position sensor Lower
Paper exit roller clutch
Off-set position sensor
Side guide plate
motor
No. 2 tray paper exit
sensor
Staple HP sensor
Staple operation motor
Stapler
No. 1 tray paper exit
sensor
Self priming sensor
Tray paper empty sensor
Side guide plate HP sensor
FAX PWB
JAM process PG
open/close sensor
Tray JAM process sensor
Staple supply cover
open/close sensor
Cartridge empty sensor
Staple empty sensor
Finisher Unit (Optional)
Mother PWB
Down-Load-CON
Option interface
PWB
Polygon-Motor
Toner-Motor
(include CRSM)
UNIT
DEV
CN135
SPF BOOK Sens
CN107
SPF Paper Size Sens (x5)
CN112
SPF-PSOL
CN106
SPF PS Sens
CN110
SPF Cover Sens
CN121
Mirror-Motor
CN109
SPF-SEN-PWB
CN102
TRAYPAPER
SENSOR
FINISHER PWB
SPF/RSPF Unit (Optional)
[2] SYSTEM CONFIGURATION
1. Structure
A. Hardware
Block diagram
2. System outline (Options)
Option
Item
Model
AR-VR3
AR-RP3
AR-SP4
AR-D11
AR-D12
AR-TR3
AR-FN5
AR-FX4
Platen cover
Reversing single pass feeder
Single pass feeder
500-sheet paper feed unit
2X500-sheet paper feed unit
Job separator tray kit
Finisher
Facsimile expansion kit
Fax memory
2MB
4MB
8MB
Printer expansion kit
Print server card
Network scanner expansion kit
Bar code font kit
PS3 expansion kit
Y: Installable
Main unit model
AR-235
AR-275
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y*1
Y*1
AR-MM5
AR-MM6
AR-MM7
AR-P11
Y
Y
Y
Y
Y
Y
Y
Y
AR-NC5J
AR-NS2
AR-PF1
AR-PK1
Y
Y
Y
Y
Y
Y
Y
Y
NOTE
∗1: FAX board option available only for SEC/SECL/SEEG/SEF/SUK/SCA/
SCNZ
When the printer board is set up on the machine, the function of duplex
can be automatically detected on printer mode.
For details of the options, refer to the Service Manual of each option.
(1) Main units
(2) Options
AR-235/275
AR-D12
2X500-sheet paper feed unit
AR-TR3
Job separator tray kit
AR-P11
Printer expansion kit
AR-NC5J
Print server card
(3) Expanded memory for IMC, PCL (Advisable)
Maker
Memory Card Technology
Kingston Technology
Product name
DM864VS65804X-7AG
DM864VS65804X-75G
DM1665VS65804X-7AG
DM1665VS65804X-75G
KVR100X64C2/64
KVR133X64C3/128
Capacity
AR-VR3
Platen cover
AR-RP3
Reversing single pass feeder
AR-SP4
Single pass feeder
AR-D11
500-sheet paper feed unit
AR-FN5
Finisher
AR-MM5/MM6/MM7
2/4/8MB Fax memory
AR-NS2
Network scanner expansion kit
AR-PF1
Bar code font kit
AR-PK1
PS3 expansion kit
AR-FX4
Facsimile expansion kit
Maker
Viking Components
64MByte
128MByte
64MByte
128MByte
AR-235/275 SYSTEM CONFIGURATION - 2
Product name
VIK4642CL2
VIK8641CL2
VIK6642CL2
Capacity
32MByte
64MByte
128MByte
[3] SPECIFICATIONS
• 1200 dpi mode
Copy magnification
ratio
Zoom width
Fixed magnification
mode
1. Basic specifications
(1) Type
Machine Type
Desktop type
(2) Target users
Average
Max.
10,000 to 13,000 sheets/month
50,000 sheets/month
(3) External dimensions
Packaged
Body
780 (W) × 760 (D) × 840 (H)mm
623 (W) × 585.5 (D) × 640.5 (H)mm
Independent
magnification width
(4) Weight
AR-235/275
About 55.95 kg
42.5 kg
Packaged
Copier body
Magnification
precision
(5) Machine life
Normal
• Copy magnification (Normal copy)
(1) Warm up time
Document Size
After turned on
Recovery from power-save mode
Recovery from paper jam
Under 40 seconds
Under 10 seconds
10 sec.
(2) Jam recovery time
About 10sec (Leaving the machine for 60 sec after opening the door,
standard condition, polygon stop.)
B. Copy mode
(1) Document size
A3 paper (11" × 17")
(2) Picture quality mode
Density adjustment
step
1 step
5 steps
5 steps
5 steps
5 steps
Toner save mode
Selectable
Selectable
Selectable
—
—
(3) Copy magnification ratio
• Normal mode
Copy magnification
ratio
Zoom width
Fixed magnification
mode
Independent
magnification width
Less than 4.8 seconds (when the single copy)
b. Multi copy speed (sheets/minute)
A. Common operation
Auto mode
Character mode
Text/Photo mode
Photo mode
Super Photo mode
Normal copy: 100%±1.0%
Enlargement copy: Set magnification ±1.0%
Reduction copy: Set magnification ±1.0%
a. First Copy Time
2. Operation specifications
Picture quality mode
50 to 200% (50 to 141% for SPF/RSPF)
AB Series: 50, 70, 81, 86, 100, 115, 122, 141,
200%
4R+4E
(50, 70, 81, 86, 100, 115, 122 and 141% for
SPF/RSPF)
Inch Series: 50, 64, 77, 95, 100, 121, 129,
141, 200%
4R+4E
(50, 764, 77, 95, 100, 121, 129 and 141% for
SPF/RSPF)
50 to 200% for horizontal/vertical (50 to 141%
for SPF/RSPF)
(4) Job speed
800,000 sheets or 5 years
Max. document size
Magnification range/fixed magnification
Magnification range/fixed magnification
25 to 400% (50 to 200% for SPF/RSPF)
AB Series: 25, 50, 70, 81, 86, 100, 115, 122,
141, 200, 400%
5R+5E
(50, 70, 81, 86, 100, 115, 122, 141 and 200%
for SPF/RSPF)
Inch Series: 25, 50, 64, 77, 95, 100, 121, 129,
141, 200, 400%
5R+5E
(50, 64, 77, 95, 100, 121, 129, 141 and 200%
for SPF/RSPF)
25 to 400% for horizontal/vertical (50 to 200%
for SPF/RSPF)
A3
B4
A4 (Horizontal feed)
A4 (Vertical feed)
B5 (Horizontal feed)
B5 (Vertical feed)
11" × 17"
8-1/2" × 14"
8-1/2" × 13"
8-1/2" × 11" (Horizontal
feed)
8-1/2" × 11" (Vertical
feed)
A5/INV
AR-235
600 dpi 1200 dpi
12
7.5
14
8.5
23
13.5
16
9
23
13.5
18
10.5
12
7.5
13
8
14
8.5
AR-275
600 dpi 1200 dpi
15
7.5
17
8.5
27
13.5
18
9
27
13.5
21
10.5
15
7.5
16
8
17
8.5
23
13.5
27
13.5
16
9
18
9
23
13.5
27
13.5
∗ The slowest speed is listed in enlargement/reduction copy.
∗ Single-side copy
• Copy magnification (Reduction copy (50% to 99%))
Document Size
A3
B4
A4 (Horizontal feed)
A4 (Vertical feed)
B5 (Horizontal feed)
B5 (Vertical feed)
11" × 17"
8-1/2" × 14"
8-1/2" × 13"
8-1/2" × 11" (Horizontal
feed)
8-1/2" × 11" (Vertical
feed)
A5/INV
AR-235
600 dpi 1200 dpi
12
7.5
14
8.5
23
13.5
16
9
23
13.5
18
10.5
12
7.5
13
8
14
8.5
AR-275
600 dpi 1200 dpi
15
7.5
17
8.5
27
13.5
18
9
27
13.5
21
10.5
15
7.5
16
8
17
8.5
23
13.5
27
13.5
16
9
18
9
23
13.5
27
13.5
∗ The slowest speed is listed in enlargement/reduction copy.
∗ Single-side copy
AR-235/275 SPECIFICATIONS - 1
3. Engine specifications
• Copy magnification (Enlargement copy (100% to 200%))
Document Size
A3
B4
A4 (Horizontal feed)
A4 (Vertical feed)
B5 (Horizontal feed)
B5 (Vertical feed)
11" × 17"
8-1/2" × 14"
8-1/2" × 13"
8-1/2" × 11" (Horizontal
feed)
8-1/2" × 11" (Vertical
feed)
A5/INV
AR-235
600 dpi 1200 dpi
12
7.5
14
8.5
23
13.5
16
9
23
13.5
18
10.5
12
7.5
13
8
14
8.5
AR-275
600 dpi 1200 dpi
15
7.5
17
8.5
27
13.5
18
9
27
13.5
21
10.5
15
7.5
16
8
17
8.5
23
13.5
27
13.5
16
9
18
9
23
13.5
27
13.5
∗ The slowest speed is listed in enlargement/reduction copy.
A. Operation and display section
Display unit
Operation system
B. Paper feed, transport, paper exit section
(1) Paper feed ability
Paper feed
section
Paper feed
capacity
Document Size
Remaining
detection
Remarks
Capacity
Paper weight
Document Size
(5) Max. multi-copy (print) quantity
999 sheets
(6) Picture quality
a. Image process
Picture quality mode
Auto mode
Text mode
Text/Photo mode
Photo mode
Super Photo mode
Image process (Software)
• 2 gradations
• Area separation
• Error diffusion
Dither
b. Toner save mode
10%
Paper kind
Special paper
Paper size
selection
Slide switch
Cassette
attachment/
detachment
Remarks
c. Zoom method
Main scanning
direction
Sub scanning direction
Performed through image processing
Performed by image processing and
changing scanning speed
Capacity
Paper weight
Document Size
Paper kind
• Read
Main scanning direction
Basic
Virtual
resolution
resolution
400 dpi
—
Sub scanning direction
Basic
Virtual
resolution
resolution
400 dpi
—
• Write
Main scanning direction
Basic
Virtual
resolution
resolution
600 dpi
1200 dpi
Sub scanning direction
Basic
Virtual
resolution
resolution
600 dpi
1200 dpi
Position
Center
—
3.2 line/mm
3.6 line/mm
5.0 line/mm
5.0 line/mm
5.0 line/mm
AB Series: A3 to A6R
Inch Series: 11"×17" to 8.5"×5.5"
Cassette section: empty detection only available
Manual paper feed section: empty detection only
available
—
Corners
—
2.8 line/mm
3.2 line/mm
4.5 line/mm
4.5 line/mm
4.5 line/mm
—
56 to 80 g/m² (15 to 21.3 lbs)
AB Series: A3/B4/A4/A4R/B5/B5R/A5
Inch Series: 8.5×11/8.5×14/11×17/8.5×13/
8.5×11R/8.5×5.5
Standard paper (56 to 80 g/m²), special paper
Reproduction paper
User operation (LCD panel operation)
—
Yes
A5, B5, 8.5 x 5.5 (only for upper cassette)
B5 is not applicable to lower cassette (2nd
stage).
Size detection
Guide display
100 sheets (52g to 80g/m²)
52 to 128 g/m² (14 to 34.1 lbs)
AB Series: A3 to A6R
Inch Series: 11"×17" to 8.5"×5.5"
Multi feed: Standard paper (52 to 80 g/m²),
special paper (Reproduction paper/OHP/label
paper/postcard/envelope)
Single feed: Standard paper (52 to 128 g/m²),
special paper (Reproduction paper/OHP/label
paper/postcard/envelope)
Yes
A3/A4,11,B4/B5,8.5,A4R/A5,B5R,A5R,5.5
∗ When poor image quality is resulted by the use of OHP sheet, adjust
with SIM 44-34.
(2) Finishing ability
Paper exit section
Capacity
Paper exit tray (1 tray)
500 sheets
(3) Job separator exit tray (AR-TR3)
a. Condition
In case of Optional function (printer, FAX) is set up as MFD.
b. Simultaneous wrapping in kit
Job separator tray
Setting manual book
e. Gradation
Read
Write
500×2+100
• Manual feed section
d. Resolution
Copy magnification
ratio
25% to 49%
50% to 69%
70% to 94%
95% to 105%
106% to 141%
142% to 400%
2 cassettes + multi manual feed
• Details of paper feed section
∗ Single-side copy
Toner save percentage
LED display system
Button switch system
256 gradations
2 gradations
c. Simultaneous wrapping
Setting manual book
d. Function
This exit tray is set up above main exit tray, and can separate copier
exit, printer exit and FAX exit.
AR-235/275 SPECIFICATIONS - 2
(5) Original size/Scanning area
e. Many of tray
1 (this tray can not set up more than 2)
a. Max. original size
f. Separator system
A3 paper (11" × 17")
by control of main machine
b. Scanning area
g. Exit paper size
Upper exit tray (Job separator
tray)
Lower exit tray (Main machine
exit tray)
CENTER
AB system
Inch system
AB system
Inch system
A3 to A6
11 x 17 to 8.5 x 5.5
A3 to A6
11 x 17 to 8.5 x 5.5
h. Exit paper weight
52 to 128g/m! (14 to 34.1lbs)
356 mm
i. Paper pass
center (same as main unit)
j. Exit area/finishing
Upper exit tray (Job separator tray)
Lower exit tray (main machine exit tray)
Face down
Face down
k. Power supply
Power supply
Power consumption
DC 24V (from main machine)
5.6W
(6) Scanning speed
l. Method of movement
with original motor (not with main machine)
122mm/sec (600 dpi: magnification ratio 100%)
61mm/sec (1200 dpi: magnification ratio 100%)
m. Machine weight
(7) Light source (lamp)
0.6 kg
n. Exit capacity
Upper exit tray (Job separator)
Lower exit tray (main machine exit tray)
100 sheets
500 sheets (550 sheets)
Upper exit tray (Job separator)
Lower exit tray (main machine exit tray)
Yes
No
Lower exit tray (main machine
exit tray)
Xenon
1.5 kV
(8) Read sensor
Reduction optical system image sensor (CCD)
Monochrome
D. Scanner (exposure) section
p. Concept of function
Upper exit tray (Job separator)
Type
Drive voltage
Type
o. Tray full detector
(1) Resolution
FAX/Printer (This setting can be
done by users.)
Copy/Printer/FAX (This setting can
be done by users.)
Main scanning direction
600 dpi
Sub scanning direction
600 dpi
(2) Gradation
2 gradations
q. Reliance
MCBJ
MCBF
216 mm
(3) Laser unit specifications
60k
10k
r.p.m.
Mirror surfaces
Laser power
Laser beam size
Laser wave length
r. Main color of cabinet
Frosty white
s. Setting
to be easy setting
E. Image process section
C. Optical (Image scanning) section
Imaging speed
(1) Type
Photo
conductor
Flat-bed type/monochrome
(2) Document reference position
Toner
Rear left reference
Type
LIFE
Type
LIFE
(3) Resolution
Main scanning direction
Basic
Virtual
resolution
resolution
400 dpi
—
(4) Gradation
28,800 rpm
6 faces
0.4mW/600dpi, 0.2mW/1200dpi
60µ (Main scan) x 70µ (Sub scan)
785nm
Sub scanning direction
Basic
Virtual
resolution
resolution
400 dpi
—
Charge
Transfer
Exposure
Developing
256 gradations (8-bit)
Separation
Discharge
Cleaning
AR-235/275 SPECIFICATIONS - 3
System
Voltage
System
Voltage
600 dpi : 122 mm/sec.
1200 dpi : 61 mm/sec.
OPC drum (dia. 30mm)
50,000 sheets
Developer (Black)
25,000 sheets (Toner, life: 25k, Developer life:
50k)
(–) DC scorotron (saw tooth)
560µA constant electric current
Transfer roller
18µA (electric current)
Xenon lamp
Dry, 2-component magnetic brush
development
(–) DC corotron
—
Blade
5. Environment conditions
F. Fusing
Type
Voltage
Power
consumption
Fusing temperature
Heat roller
Pressure roller
Separation system
Heat roller
Halogen lamp
100V
1000W
(1) Space required
Folded multi manual feed
Open multi manual feed
(2) Operating ambient conditions
185° (600 dpi)
160° (1200 dpi)
Teflon coated roller
Silicone rubber roller with roentgerized
cube
Natural separation (with pawl)
G. DRIVE
Drive section
Main motor
623 (W) × 585.5 (D) mm
889 (W) × 585.5 (D) mm
Motor
DC brushless motor
Humidity (%)
Type
Lamp
4. Safety and environmental protection
standards
Temperature (˚C)
(1) Safety and environmental protection standards
EnergyStar
Standard name
S mark
VCCI class A
VCCI class B
Country name
Japan
Japan
Taiwan
World-wide
(2) Ozone level
Ozone
Dust
(3) Ambient storage conditions
Less than 0.02mg/m³
Less than 0.075mg/m³
Humidity (%)
Item
Safety
standards
Radio wave
noise standard
(3) Noise level
Less than 63dB
Less than 40dB
Temperature (˚C)
(4) Ambient conditions for transporting
Humidity (%)
Operating
On standby
Temperature (˚C)
(5) Atmospheric pressure
595 mmHg or above
(6) Standard temperature and humidity
Temperature
Humidity
AR-235/275 SPECIFICATIONS - 4
20 to 25°C
65±5%RH
[4] CONSUMABLE PARTS
1. List
A. SEC/LAG
No.
Item
Content
1 Toner CA (black) w/IC Toner
Vinyl bag
2 Developer
Developer
(Developer; Net weight
500g)
3 Drum kit
Drum
4 Upper heat roller kit
Upper Heat Roller
Fusing gear
Upper heat roller bearing
Fusing separation pawl
(upper)
5 Lower heat roller kit
Lower Heat Roller
Fusing separation pawl
(lower)
Fusing busing (lower)
6 100K maintenance kit Drum Separation Unit
Transfer roller unit
7 MC unit
MC unit
8 Cleaner Blade
Cleaner Blade
9 Drum frame unit
Drum frame unit
×10
×10
×10
Life
25K (×10)
50K (×10)
Model name
Remarks
AR-270MT Life setting by A4 (8.5"×11") 6% document
MT=NT*10
AR-270MD MD=ND*10
×1
×1
×1
×2
×4
50K
150K
AR-270DR
AR-270UH
×1
×4
300K
AR-270LH
100K
AR-270KA1
×2
×2
×1
×10
×10
×1
50K (×10)
50K (×10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
11 Transfer roller unit
12 Paper feed roller kit
13 Fusing unit
Transfer roller unit
Paper feed roller kit
Fusing unit
×3 3000 staples
×3
×1
100K
×1
100K
×1
150K
AR-SC1
AR-270TX
AR-270IR
AR-270FU
Paper feed roller, pickup roller, separation sheet
* The other maintenance parts than the above are supplied as service parts.
B. SECL
No.
Item
Content
1 Toner CA (black) w/IC Toner
Vinyl bag
2 Developer
Developer
(Developer; Net weight
500g)
3 Drum kit
Drum
4 Upper heat roller kit
Upper Heat Roller
Fusing gear
Upper heat roller bearing
Fusing separation pawl
(upper)
5 Lower heat roller kit
Lower Heat Roller
Fusing separation pawl
(lower)
Fusing busing (lower)
6 100K PM kit
Drum Separation Unit
Transfer roller unit
DV blade
Side seal F
Side seal R
7 MC unit
MC unit
8 Cleaner Blade
Cleaner Blade
9 Drum frame unit
Drum frame unit
×10
×10
×10
Life
25K (×10)
50K (×10)
Model name
Remarks
AR-270MT Life setting by A4 (8.5"×11") 6% document
MT=NT*10
AR-270MD MD=ND*10
×1
×1
×1
×2
×4
50K
150K
AR-270DR
AR-270UH
×1
×4
300K
AR-270LH
100K
AR-270KA
×2
×2
×1
×1
×1
×1
×10
×10
×1
50K (×10)
50K (×10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
* The other maintenance parts than the above are supplied as service parts.
AR-235/275 CONSUMABLE PARTS - 1
C. Europe affiliates/East Europe/SEEG/SUK/SCA/SCNZ/SEA/SEES/SEZ/SEIS/SEB/SEN/SEF/SMEF/Russia/
Middle East/Africa/CIS
No.
Item
Content
1 Toner CA (black) w/IC Toner
Vinyl bag
2 Developer
Developer
(Developer; Net weight
500g)
3 Drum kit
Drum
4 Upper heat roller kit
Upper Heat Roller
Fusing gear
Upper heat roller bearing
Fusing separation pawl
(upper)
5 Lower heat roller kit
Lower Heat Roller
Fusing separation pawl
(lower)
Fusing busing (lower)
6 100K PM kit
Drum Separation Unit
Transfer roller unit
DV blade
Side seal F
Side seal R
7 MC unit
MC unit
8 Cleaner Blade
Cleaner Blade
9 Drum frame unit
Drum frame unit
×10
×10
×10
Life
25K (×10)
50K (×10)
Model name
Remarks
AR-270LT Life setting by A4 (8.5"×11") 6% document
LT=T*10
AR-270LD LD=DV*10
×1
×1
×1
×2
×4
50K
150K
AR-270DM
AR-270UH
×1
×4
300K
AR-270LH
100K
AR-270KA
×2
×2
×1
×1
×1
×1
×10
×10
×1
50K (×10)
50K (×10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
11 Transfer roller unit
12 Paper feed roller kit
13 Fusing unit
Transfer roller unit
Paper feed roller kit
Fusing unit
×3 3000 staples
×3
×1
100K
×1
100K
×1
150K
AR-SC1
AR-270TX
AR-270IR
AR-270FU
* The other maintenance parts than the above are supplied as service parts.
AR-235/275 CONSUMABLE PARTS - 2
Paper feed roller, pickup roller, separation sheet
D. Special country/Taiwan
No.
Item
Content
1 Toner CA (black) w/IC Toner
Vinyl bag
2 Developer
Developer
(Developer; Net weight
500g)
3 Drum kit
Drum
4 Upper heat roller kit
Upper Heat Roller
Fusing gear
Upper heat roller bearing
Fusing separation pawl
(upper)
5 Lower heat roller kit
Lower Heat Roller
Fusing separation pawl
(lower)
Fusing busing (lower)
6 100K PM kit
Drum Separation Unit
Transfer roller unit
DV blade
Side seal F
Side seal R
7 MC unit
MC unit
8 Cleaner Blade
Cleaner Blade
9 Drum frame unit
Drum frame unit
×10
×10
×10
Life
25K (×10)
50K (×10)
Model name
Remarks
AR-270CT Life setting by A4 (8.5"×11") 6% document
CT=ST*10
AR-270CD CD=SD*10
×1
×1
×1
×2
×4
50K
150K
AR-270DR
AR-270UH
×1
×4
300K
AR-270LH
100K
AR-270KA
×2
×2
×1
×1
×1
×1
×10
×10
×1
50K (×10)
50K (×10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
11 Transfer roller unit
12 Paper feed roller kit
13 Fusing unit
Transfer roller unit
Paper feed roller kit
Fusing unit
×3 3000 staples
×3
×1
100K
×1
100K
×1
150K
AR-SC1
AR-270TX
AR-270IR
AR-270FU
Paper feed roller, pickup roller, separation sheet
* The other maintenance parts than the above are supplied as service parts.
E. Asia affiliates /Asia agent/STCL/SRH/SRS/SRSSC/SBI
No.
Item
Content
1 Toner CA (black) w/IC Toner
Vinyl bag
2 Developer
Developer
(Developer; Net weight
500g)
3 Drum kit
Drum
4 Upper heat roller kit
Upper Heat Roller
Fusing gear
Upper heat roller bearing
Fusing separation pawl
(upper)
5 Lower heat roller kit
Lower Heat Roller
Fusing separation pawl
(lower)
Fusing busing (lower)
6 100K PM kit
Drum Separation Unit
Transfer roller unit
DV blade
Side seal F
Side seal R
7 MC unit
MC unit
8 Cleaner Blade
Cleaner Blade
9 Drum frame unit
Drum frame unit
×10
×10
×10
Life
25K (×10)
50K (×10)
Model name
Remarks
AR-270CT Life setting by A4 (8.5"×11") 6% document
CT=ST*10
AR-270CD CD=SD*10
×1
×1
×1
×2
×4
50K
150K
AR-270DR
AR-270UH
×1
×4
300K
AR-270LH
100K
AR-270KA
×2
×2
×1
×1
×1
×1
×10
×10
×1
50K (×10)
50K (×10)
200K
AR-270MC
AR-270CB
AR-270DU * The life of the toner reception seat welded to the
drum frame is 200K, and it can be used up to 4
times. (Supplied as a drum frame unit.)
* Drum frame unit contains all the drum unit parts
excluding Drum and Drum fixing plate.
10 Staple Cartridge
Staple Cartridge
×3 3000 staples
×3
AR-SC1
* The other maintenance parts than the above are supplied as service parts.
AR-235/275 CONSUMABLE PARTS - 3
2. Production number identification
3. Environment conditions
<TD cartridge>
A. Ambient conditions for transporting
Serial number
(0001-9999)
The end digit of
production year
~
Destination
~
Unit version
Production
month
1
January
September
October
November
December
9
0
X
Y
Humidity (%)
The label on the TD cartridge shows the date of production.
Temperature (˚C)
Humidity (%)
B. Ambient storage conditions (sealed)
Label position
<Drum>
The laser print indicates the date (year, month, day) of production.
Temperature (˚C)
Humidity (%)
C. Operating ambient conditions
1
2
Use environment
conditions
3
1
The last digit of the production year.
2
The prodoction month.
3
The production sub lot.
Temperature (˚C)
X stands for October, Y November, and Z December.
4. Life (packed conditions)
Photoconductor drum (36 months from the production month)
Developer, toner (24 months from the production month)
AR-235/275 CONSUMABLE PARTS - 4
[5] UNPACKING AND INSTALLATION
1. Removal of protective material and fixing
screw
1) Remove all tapes, then open the document cover and remove the
protective material of sheet shape.
2) Remove the fixing screw using a coin.
Fixing screw
The fixing screw is required when transporting the machine. Keep
it in the tray. (Refer to the later description.)
∗ If power is turned don without removing the fixing pin, it will be diffi-
cult to pull out the tray.
3. Developer cartridge installation
1) Hold the both sides of the front cover, and pull down to open it.
2. Removal and storage of fixing pin
1) Lift the knob and gently pull out the tray.
2) Loosen the screw and remove the developer cartridge.
TD cartridge lock
release lever
2) Hold the paper pressure plate and turn the fixing pin in the arrow
direction.
3) Remove the developer tank from the developer cartridge.
3) Store the removed fixing pin and the fixing screw which was
removed in the above procedure, together in the specified storage
place in the tray.
4) Supply developer into the developer tank while rotating the MG
roller.
Hook
Fixing pin
∗ Shake the developer bag enough before opening it.
∗ Check to insure that the hook is engaged in two positions.
5) Attach the developer tank to the developer cartridge.
After supplying developer into the developer cartridge, do not tilt or
shake the developer cartridge.
6) Attach the developer cartridge to the copier, and fix it with the
screw.
Note: When replacing the OPC drum with a new one, be sure to clear
the drum count.
AR-235/275 UNPACKING AND INSTALLATION - 1
4. Toner cartridge installation
• Screen display
1) Shake the toner cartridge several times horizontally, and remove
the tape.
4 or 5 times
3) On the screen, all trays are indicated and the previously selected
tray is highlighted. Use the Up/Down key to select the tray desired.
Shutter
• Screen display
Tape
Knob
∗ Do not hold the shutter lever when shaking.
2) Press the lock release lever, and insert the unit completely into the
copier along the guide groove. Then fix the blue screw and the
locking screw.
∗ Dirt or dust must be removed from the toner cartridge before
installing.
4) After selecting the tray, press the Right cursor key to move to the
paper size selection box on the right side of the screen (the highlighted size is the previously selected size). Use the Up/Down key
to select the desired paper size.
5) After selecting the paper size, press the Left cursor key to return to
the left side of the screen. At that time, the selected tray indicates
the paper size selected above.
3) Take off the tape, and remove the shutter from the toner cartridge.
Press the OK key to confirm the setting. The following message
appears:
• Message (M081)
5. Toner concentration sensor level
adjustment
1) Open the cover.
2) Power ON (The mechanism cannot be initialized because the
cover is open.)
3) Install the developing unit with new developer in it.
4) Enter SIM 25-2.
6) After the Start key is pressed, if the fed paper is different in size
from the setting, the machine makes copy and then stops running
with the mode retained. The following message appears for six
seconds. the Start LED is ON): The tray set EXTRA size is not
available for this specification.
• Message (C449)
5) Close the cover immediately before starting the operation.
6) Press the OK key to start.
After completion of the adjustment, be sure to cancel the simulation.
Note: When replacing developer with new one, be sure to clear the
developer counter.
6. Paper size selection for paper feed tray
1) The paper feed trays have no paper size detection mechanism and
the paper size can be selected by entry from the operation panel.
The bypass tray has a paper size detection mechanism and the
paper size cannot be selected from the operation panel.
7) If any of Trays 2 to 4 is selected, the paper sizes of A5/5.5 x 8.5 are
not available (because the A5/5.5 x 8.5-sized paper cannot be fed
from these trays).
2) To select the paper size from the operation panel, press the Special Function key and choose "Paper Size Enter" from the function
menu to open the paper size enter screen.
AR-235/275 UNPACKING AND INSTALLATION - 2
[6] EXTERNAL VIEW AND INTERNAL STRUCTURE
1. External view
1
2
3
4
5
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
4
Name
Platen cover (optional)
Paper output tray
Front cover
Paper trays
Power switch
Handles
Operation panel
Original table
Upper exit area cover
Side cover
Side cover handle
Bypass tray guides
Bypass tray
Bypass tray extension
6
Function/Operation
Place the original on the original table and close the platen cover before copying starts.
Finished copies are deposited in the paper output tray.
Open to remove misfeeds and for copier servicing.
Each tray holds 500 sheets of copy paper.
Press to turn copier power on and off.
Use to move the copier.
All copier controls are located here for easy operation.
Place the document to be copied here.
Open to remove misfeeds when an optional job separator tray kit or finisher is installed.
Open to remove misfeeds.
Lift and pull to open the side cover.
Adjust to the width of the copy paper.
Special papers (including transparency film) and copy paper can be fed from the bypass tray.
Pull out when feeding large paper such as 8-1/2" x 14" and 11" x 17".
2. Internal
1
2
3
4
5
No.
1
2
3
4
5
4
Name
Toner cartridge lock release lever
Toner cartridge
Paper guide
Fusing unit release levers
Roller rotating knob
6
Function/Operation
Use to unlock the toner cartridge.
Contains toner.
Open to remove misfed paper.
Lower to remove misfed paper.
Turn to remove misfed paper.
AR-235/275 EXTERNAL VIEW AND INTERNAL STRUCTURE - 1
3. Operation panel
A. Key position
(U.S.A., Canada)
1
2
12
13 14
3
15
16
17
4
18
5 6
7
19 20
21
8
9
22
10
11
23
These keys and indicators are not used
for the copier features
No.
1
Name
COPY key and indicator
Function/Operation
Press to select the COPY mode.
Press and hold during standby to display the total output count. Quantity of toner remaining is also displayed.
Displays information to assist the operator.
Press to return the display to the previous screen.
Press to display the detailed description when [i] is displayed at the upper right of the display.
Press to check the settings of selected functions or the status of reserved output jobs.
Press to register the selected setting.
Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are
made.
Used to select the desired copy quantity.
Interrupts a copy run.
2
3
4
5
6
7
Display
BACK key
Information key
JOB STATUS key
OK key
Copy quantity display
8
9
10
11
Numeric keys
INTERRUPT key and
indicator
CLEAR ALL key
START key and indicator
12
13
14
15
16
EXPOSURE key
PAPER SELECT key
COPY RATIO key
AUTO IMAGE key
2-SIDED COPY key
17
OUTPUT key
18
19
20
21
SPECIAL FUNCTION key
Arrow keys
AUDIT CLEAR key
Zero key
22
PROGRAM/READ END
key
CLEAR key
23
Clears all selected settings and returns the copier to the initial settings.
Copying is possible when the indicator is on.
Press to start copying.
Used to select the exposure modes: AUTO, TEXT, TEXT/PHOTO, PHOTO or SUPER PHOTO.
Used to manually select a paper tray.
Press to select a reduction or enlargement copy ratio.
Press for automatic copy ratio selection.
Press to select the 1-sided to 1-sided, 1-sided to 2-sided, 2-sided to 1-sided* or 2-sided to 2-sided* copy mode.
*To select the 2-sided to 1-sided or 2-sided to 2-sided copy mode, an optional RSPF must be installed.
Press to select the sort, group or staple sort* mode.
*To select the staple sort mode, an optional finisher must be installed.
Press to select special functions.
Press to move the highlighted item in the display.
Press to close an open account.
Use as part of numeric keys to enter copy quantity.
Press during a continuous copy run to display the number of copies completed in the current run.
Press to select the job memory mode.
Press to finish scanning of originals and to start copying when copying from the original table.
Press to clear the copy quantity display or press during a copy run to terminate copying.
B. LCD panel
(U.S.A., Canada)
1
4
2
5
3
6
No.
1
2
Name
Exposure display
Message display
3
4
Original size display
Copy ratio display
5
Paper size display
6
Paper tray display
AR-235/275 EXTERNAL VIEW AND INTERNAL STRUCTURE - 2
Function/Operation
Indicates the selected exposure mode.
Messages are displayed regarding
copier status and operation.
The original paper size is displayed.
Displays the copy ratios for reductions
or enlargements.
Displays the selected paper size.
When "AUTO" is displayed, paper size
matching the original and copy ratio
will be automatically selected.
The selected paper feed location is
highlighted.
4. Motor, Solenoid, Clutch
5. Sensor
2
3
1
1
4
18
2
29
17
3
28
4
27
5
6
7
5
8
6
9
7
26
10
11
12
13
14
8
9
25
10
14
13
12
17
24
16
11
30
23
18
22
21
15
No.
1
2
3
4
Name
Mirror motor
Shifter motor
Paper exit gate
switching solenoid
Duplex motor
5
Cooling fan
6
7
8
Main motor
PS clutch
Manual paper feed
solenoid
Manual paper feed
clutch
Paper feed transfer
clutch
Paper feed clutch
Cassette lift-up motor
Paper feed solenoid
9
10
11
12
13
14
17
2nd cassette paper
feed solenoid
Toner motor
Separation pawl
solenoid
Exhaust fan motor
18
Intake fan motor
15
16
20
Code
MIRM
SFTM
Function and operation
Optical mirror base drive
Shifter drive
Paper exit gate switcher
PGSOL
DPXM
TFAN
MM
PSRSOL
HPSOL
PCL1H
LUM1H
PCS1H
TM
PREMS
OL
PSFAN
Duplex paper switching
and exit roller
Cools the inside of the
unit.
Main drive
Main unit paper feed
Manual paper feed
solenoid
Manual paper feed clutch
Paper feed transfer
clutch
Paper feed roller drive
Cassette paper lift-up
Solenoid for the paper
feed from the cassette
Toner supply
Separation pawl
operation solenoid
Cools the inside of the
unit.
15
16
No
.
1
Name
19
Code
Original size sensor
DSIN0
2
Mirror home position
sensor
MHPS
3
4
Document cover
sensor
Document size sensor
5
1st paper exit sensor
POUT
6
SFTHP
8
Shifter home position
sensor
Paper exit sensor
(DUP side)
Thermistor
9
Thermostat
10
Manual feed paper
entry sensor
HPIN
11
1st cassette (paper
tray) detection
Manual feed paper
empty sensor
2nd cassette (paper
tray) detection
Manual feed width
detection volume
Manual paper feed
tray empty sensor 2
Manual paper feed
tray empty sensor 1
Manual feed length
detection sensor 2
Manual feed length
detection sensor 1
CSS1
7
12
13
14
15
16
17
18
AR-235/275 EXTERNAL VIEW AND INTERNAL STRUCTURE - 3
OCCOVER
DSIN3
PDPX
RTHIN
HPEMPTY
HPWS
HPTRAY2
HPTRAY1
HPSIZE2
HPSIZE1
Function and
operation
Document size
detection
Mirror (scanner)
home position
detection
Document cover
open/close detection
Document size
detection
1st paper exit
detection
Shifter home position
sensor detection
Paper exit detection
Fusing temperature
detection
Abnormal high
temperature detection
in the fusing section
Sensor of paper entry
from the manual
paper feed tray, the
2nd/multi-stage desk,
or the DUP
1st cassette (paper
tray) empty detection
Manual feed paper
empty detection
2nd cassette (paper
tray) empty detection
Manual feed paper
width detection
Manual feed tray
position detection
Manual feed tray
position detection
Manual feed paper
length detection
Manual feed paper
length detection
No
.
19
Name
Code
Door switch
SW24V
20
2nd right door switch
21
2nd cassette paper
pass sensor
2nd cassette paper
upper limit detection
sensor
2nd cassette paper
empty sensor
1st cassette paper
upper limit detection
sensor
1st cassette paper
empty sensor
Center tray peper
YES/NO sensor
Right cabinet door
switch
2nd paper exit sensor
22
23
24
25
26
27
28
29
LUD1H
PAP1H
TRAYPAPER
POUTCOV
2nd paper exit full
detection sensor
1st cassette paper
pass sensor
30
POUT2
PFULL2
Function and
operation
Front door and side
door open/close
detection
Side door open/close
detection
2nd cassette paper
pass
2nd cassette paper
upper limit detection
7. Section
1 2
3
6
23
7
8
9
10
11
12
13
14
1st cassette paper
empty detection
Center tray peper
YES/NO detection
Right cabinet door
open/close detection
2nd paper exit
detection
2nd paper exit section
full detection
1st cassette paper
pass
16
17
18
19
22
No.
1
2
Name
Copy lamp
Copy lamp unit
3
LSU unit
4
Lens unit
5
MC holder unit
6
7
8
Paper exit roller
Transport roller
Upper heat roller
9
Lower heat roller
10
11
12
13
Drum unit
DUP transport follower
roller
DUP transport roller
Transport roller
14
Resist roller
15
16
Manual feed tray
Manual paper feed roller
17
Manual feed transport
roller
1st cassette pick-up
roller
1st cassette paper feed
roller
2nd cassette pick-up
roller
2nd cassette paper feed
roller
MG roller
2nd/3rd mirror unit
1
2
3
4
11
5
6
10
9
7
18
No.
1
2
3
4
5
6
Name
Inverter PWB
CCD PWB
Option connector PWB
IMC PWB
MCU PWB
Mother board
7
8
9
10
11
Tray interface PWB
KEY/LED PWB (right side)
LCD back light PWB
KEY/LED PWB (left side)
Power source PWB
5
2nd cassette paper
empty detection
1st cassette paper
upper limit detection
6. PWB unit
8
4
Function and operation
Copy lamp control
For image scanning (read)
19
20
Image process
Main unit control
Connection with FAX PWB and
PCL PWB
2nd tray control
For the copy operation
LCD control
For the FAX operation
AC power input/DC voltage
control
21
22
23
AR-235/275 EXTERNAL VIEW AND INTERNAL STRUCTURE - 4
15
21 20
Function and operation
Image radiation lamp
Operates in synchronization with
2nd/3rd mirror unit to radiate
documents sequentially.
Converts image signals into laser
beams to write on the dum.
Reads images with the lens and
the CCD.
Supplies negative charges evenly
on the drum.
Paper exit roller
Paper transport roller
Fuses toner on paper.
(with the teflon roller)
Fuses toner on paper.
(with the silicone rubber roller)
Forms images.
Duplex paper transport
Duplex paper transport
Transfer images on the drum onto
paper.
Synchronize the paper lead edge
with the image lead edge.
Manual feed paper tray
Picks up papers in manual paper
feed port.
Transports paper from the manual
paper feed port.
Picks up paper from the cassette.
Transports the picked up paper to
RESIST section.
Picks up paper from the cassette.
Transports the picked up paper to
RESIST section.
Puts toner on the OPC drum.
Reflects the images from the copy
lamp unit to the lens unit.
[7] ADJUSTMENTS, SETTING
1. List of adjustment items
A
Section
Process section
B
Mechanism section
Adjustment item
Developing doctor gap adjustment
MG roller main pole position adjustment
Developing bias voltage adjustment
Grid bias voltage adjustment (High mode)
Grid bias voltage adjustment (Low mode)
OC image lead edge position/Sub scanning
magnification ratio/Original offset auto adjustment
Print start position adjustment
SPF image lead edge position adjustment
Rear edge void adjustment
Paper off center adjustment
Left edge void area adjustment
Main scanning direction (FR direction) distortion
balance adjustment
(1)
(2)
(3)
(4)
(5)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Sub scanning direction (scanning direction)
distortion adjustment
Main scanning direction (FR direction) distortion
adjustment
Main scanning direction (FR direction)
magnification ratio adjustment
Sub scanning direction (scanning direction)
magnification ratio adjustment
(9)
(10)
(11)
(12)
(13)
(14)
(15)
C
Image density
(exposure) adjustment
Off center adjustment (SPF mode)
OC (SPF) open/close detection position adjustment
Original sensor adjustment
SPF white correction pixel position adjustment
(required in an SPF model when replacing the lens
unit)
Copy mode
(1)
2. Copier adjustment
Adjustment procedure/SIM No.
Developing doctor gap adjustment
MG roller main pole position adjustment
SIM8-1
SIM8-2
SIM8-3
SIM48-3
SIM50-5
SIM50-6
SIM50-1-6
SIM50-10
SIM50-1-8
No. 2/3 mirror base unit installing position
adjustment
Copy lamp unit installing position adjustment
Winding pulley position adjustment
Rail height adjustment
SIM48-1-1, 48-1-2
a
b
OC mode in copying (SIM 48-1-3)
RSPF sub scanning direction magnification ratio
(SIM48-1-4, 48-1-5)
SIM50-12
SIM41-3
SIM41-2, 41-4
SIM63-7
SIM46-2
<Adjustment specification>
Developing doctor gap
A. Process section
+0.1mm
F/R both ends (20mm from the both ends):1.5 -0.15mm
(1) Developing doctor gap adjustment
C (Center)(150mm from the both ends):
1) Loosen the developing doctor fixing screw A.
2) Insert a thickness gauge of 1.5mm to the three positions at 20mm
and 150mm from the both ends of the developing doctor as shown.
+0.15mm
1.55-0.2mm
(2) MG roller main pole position adjustment
1) Put the developing unit on a flat surface.
2) Tie a needle or pin on a string.
150mm
20mm
3) Hold the string and bring the needle close to the MG roller horizontally. (Do not use paper clip, which is too heavy to make a correct
adjustment.) (Put the developing unit horizontally for this adjustment.)
10mm
10mm
R
20mm
DG:1.5 -+0.1
0.15
C
4) Do not bring the needle into contact with the MG roller, but bring it
to a position 2 or 3mm apart from the MG roller. Mark the point on
the MG roller which is on the extension line from the needle tip.
5) Measure the distance from the marking position to the top of the
doctor plate of the developing unit to insure that it is 18mm.
If the distance is not within the specified range, loosen the fixing
screw A of the main pole adjustment plate, and move the adjustment plate in the arrow direction to adjust.
DG:1.55 -+0.15
0.2
F
DG:1.5 -+0.1
0.15
3) Tighten the developing doctor fixing screw.
4) Check the clearance of the developing doctor. If it is within the
specified range, then fix the doctor fixing screw with screw lock.
∗ When inserting a thickness gauge, be careful not to scratch the
developing doctor and the MG roller.
AR-235/275 ADJUSTMENTS - 1
(5) Grid bias voltage adjustment (Low mode) (SIM 8-3)
1) Execute SIM 8-3.
Sim8-3 MHV(L) COPY
1:AE
3
2:TEXT
5
3:TEXT/PHOTO
5
1/2
2) After selecting the mode, enter the adjustment value and press the
[OK] key.
3) Output will be made for 30 sec.
<Adjustment specification>
Display items
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
A
AE
Character
Character/Photo
Photo
Super photo
Toner save
Setting
range
1-8
Default
4 (–426)
5 (–450)
5 (–450)
5 (–450)
3 (–400)
2 (–375)
∗ The input value is in the increment of –25V.
(3) Developing bias voltage adjustment (SIM 8-1)
B. Mechanism section
1) Execute SIM 8-1.
Sim8-1 DV BIAS
1:AE
2:TEXT
3:TEXT/PHOTO
1/2
Content
(1) OC image lead edge position/Sub scanning
magnification ratio/Original offset auto adjustment
COPY
426
450
450
1) Set the test chart (UKOG-0011QSZZ) on the OC table.
2) Execute SIM 48-3.
2) After selecting the mode, enter the adjustment value and press the
[OK] key.
3) Output will be made for 30 sec.
Set the
test chart
<Adjustment specification>
Display items
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
Content
AE
Character
Character/Photo
Photo
Super photo
Toner save
Installation
range
200-550
Default
426 (–426V)
450 (–450V)
450 (–450V)
450 (–450V)
400 (–400V)
376 (–376V)
(4) Grid bias voltage adjustment (High mode) (SIM 8-2)
1) Execute SIM 8-2.
1) Execute SIM 50-5.
Pressing the [START] key makes a print.
Pressing the [RETURN] key returns to the mode selection.
(Initial screen)
2) After selecting the mode, enter the adjustment value and press the
[OK] key.
3) Output will be made for 30 sec.
<Adjustment specification>
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
(2) Print start position adjustment
Select the mode with the arrow keys, enter the adjustment value
with the 10-key, and press the [OK] key.
Sim8-2 MHV(H) COPY
1:AE
3
2:TEXT
5
3:TEXT/PHOTO
5
1/2
Display items
3) Make a copy.
Content
AE
Character
Character/Photo
Photo
Super photo
Toner save
∗ The input value is in the increment of –25V.
Setting
range
1-8
Default
4 (–555V)
5 (–580V)
5 (–580V)
5 (–580V)
3 (–530V)
2 (–505V)
(Input screen)
(Executing screen)
Sim50-5 PRINT EDGE
1:TRAY1
50
2:OPTION
50
3:MANUAL
50
1/2
50
Display
items
1:TRAY1
2:OPTION
3:MANUAL
4:DUPLEX
Content
1st cassette
Option cassette
Manual feed
Back print
Setting
range
0-99
1-99
Default
53
Setup of various copy conditions: Similar to the normal copy mode.
2) Measure the distance H between the paper lead edge and the
image print start position. Set the image print start position set
value again.
• 1 step of the set value corresponds to about 0.127mm shift.
• Calculate the set value from the formula below.
AR-235/275 ADJUSTMENTS - 2
99 – H/0.127 (mm) = Image print start position set value <H:
Print start position measurement value (mm)>
0mm
0mm
5
<Adjustment specification>
Adjustment
mode
SPF image
lead edge
position
SIM
Set value
Spec value
50-6
1 step:
0.127mm
shift
Lead edge void:
1 – 4mm
Image loss: 3mm or less
Setting
range
1 – 99
(4) Rear edge void adjustment
1) Set a scale as shown in the figure below.
10
A4 (8.5" x 11")
∗ Fit the print edge with the paper edge, and perform the lead
edge adjustment.
Example:99 – 5/0.127 = 99 – 39.4 = about 59
FIf the set value is not obtained from the above formula, perform the fine adjustment.
3) Execute SIM 50-1-2 to adjust the main cassette lead edge void.
• 1 step of the set value corresponds to about 0.127mm shift.
• Calculate the set value from the formula below.
B/0.127 (mm) = Lead edge void adjustment value <B: Lead edge
void (mm)>
Paper rear edge
2) Set the document size to A4 (8.5" x 11"), and make a copy at
100%.
3) If an adjustment is required, follow the procedures below.
2.5mm
5
Void amount (Standard value: 4mm or less)
2.5mm
10
Scale image
Paper rear edge
Example: When setting the lead edge void to 2.5mm:
2.5 /0.127 = about 20
<Adjustment specification>
Adjustment
mode
Main cassette
lead edge void
Print start
position
SIM
50-12
50-5
Set value
B/0.127
99 – H/0.127
Spec value
Lead edge void:
1 to 4mm
Image loss: 3mm
or less
Setting
range
1 – 99
(3) SPF image lead edge position adjustment
1) Set a scale on the OC table as shown below.
4) Execute SIM 50-1 and set the density mode to DEN-B. The currently set adjustment value is displayed.
5) Enter the set value and press the start key.
The correction value is stored and a copy is made.
<Adjustment specification>
Adjustment
mode
Rear edge
void
SIM
Set value
1 step: 0.127mm
shift
50-1-6
Spec
value
4mm or
less
Setting
range
1 – 99
(5) Paper off center adjustment
1) Perform this adjustment after execution of SIM 48-3.
2) Set a test chart (UKOG-0089SCZZ) on the document table.
3) Select a paper feed port and make a copy.
Compare the copy and the test chart. If necessary, perform the following adjustment procedure.
4) Execute SIM 50-10.
Select the mode with the arrow keys, enter the adjustment value
with the 10-key, and press the [OK] key.
Since the printed copy is used as a test chart, put the scale in
paralleled with the edge lines.
2) Make a copy, then use the copy output as an original to make an
SPF copy again.
3) Check the copy output. If necessary, perform the following adjustment procedures.
4) Execute SIM 50-6.
5) Set the SPF lead edge position set value so that the same image is
obtained as that obtained in the previous OC image lead edge
position adjustment.
Pressing the [START] key makes a print.
Pressing the [RETURN] key returns to the mode selection.
(Initial screen)
Sim50-10 PRT.CENTER
1:BYPASS
50
2:TRAY1
50
3:TRAY2
50
1/2
50
AR-235/275 ADJUSTMENTS - 3
(Input screen)
(Executing screen)
Display
Setting
Content
Default
items
range
1:BYPASS Manual feed
1-99
50
2:TRAY1
1st cassette
3:TRAY2
2nd cassette
4:TRAY3
3rd cassette
5:TRAY4
4th cassette
6:DUPLEX Back print
Setup of various copy conditions: Similar to the normal copy mode.
<Adjustment specification>
Adjustment
mode
Left edge void
Second
print surface
off-center
SIM
50-10
-2
50-10
-6
Set value
Add 1: 0.127mm
shift to R side.
Reduce 1:
0.127mm shift to L
side.
Spec value
Single:
Center
±2.0mm
Duplex:
Center
±2.5mm
50-18
Set value
1 step: 0.127mm
shift
1)
Setting
range
1 – 99
1)
1)
2)
3)
Note: Before performing this adjustment, be sure to check that the
paper off center adjustment (SIM 50-10) is completed.
1)
4)
5)
1) Set a test chart (UKOG-0089SCZZ) on the document table.
2) Select a paper feed port and make two copies.
Compare the second copy and the test chart. If necessary, perform the following adjustment procedure.
∗ The first copy does not show the void. Be sure to check the second
2) Loosen the copy lamp unit wire fixing screw.
copy.
3) Execute SIM 50-1.
Select the mode with the arrow keys, enter the adjustment value
with the 10-key, and press the [OK] key.
Pressing the [START] key makes a print.
Pressing the [RETURN] key returns to the mode selection.
(Input screen)
(Executing screen)
Sim50-1 LEAD EDGE
1:RRC-A
43
2:RRC-B
18
3:RRC-MANUAL
18
1/4 [ 1- 99] 43
Display items
Wire fixing screw
Content
Original scan start position
adjustment
2:RRC-B
RRC cancel adjustment
(Main cassette)
3:RRC-MANUAL
RRC cancel adjustment
(Manual feed cassette)
4:RRC-OPTION
RRC cancel adjustment
(Option cassette)
5:RRC-DUPLEX
RRC cancel adjustment
(back of the machine)
6:DEN-B
Rear edge void adjustment
7:DEN-B-DUP
Rear edge void adjustment
(Duplex)
8:SIDE VOID
Left edge void adjustment
(First print surface)
9:SIDE VOID-DUP Left edge void adjustment
(Duplex)
10:LOSS(OC)
Image loss quantity
adjustment
1:RRC-A
Setting
range
1 – 99
1) Remove the OC glass and the right cabinet.
(6) Left edge void area adjustment
(Initial screen)
Spec
value
0.5 – 4mm
(7) Main scanning direction (FR direction) distortion
balance adjustment
<Adjustment specification>
Adjustment
mode
Paper off
center
SIM
Setting
range
1-99
Default
43
1-99
18
1-99
18
1-99
18
1-99
18
1-99
1-99
30
50
1-99
18
1-99
18
1-5
3
Setup of various copy conditions: Similar to the normal copy mode.
AR-235/275 ADJUSTMENTS - 4
3) Manually turn the mirror base drive pulley and bring No. 2/3 mirror
base unit into contact with the positioning plate.
At that time, if the front frame side and the rear frame side of No. 2/
3 mirror base unit are brought into contact with the positioning
plate at the same time, the mirror base unit parallelism is proper.
6) Put No. 2/3 mirror base unit on the positioning plate again, push
the projections on the front frame side and the rear frame side of
the copy lamp unit to the corner frame, and tighten the wire fixing
screw.
If one of them is in contact with the positioning plate, perform the
adjustment of 4).
4) Loosen the set screw of the scanner drive pulley which is not in
contact with No. 2/3 mirror base unit positioning plate.
5) Without moving the scanner drive pulley shaft, manually turn the
scanner drive pulley until the positioning plate is brought into contact with No. 2/3 mirror base unit, then fix the scanner drive pulley.
(8) Sub scanning direction (scanning direction) distortion
adjustment (Winding pulley position adjustment)
This adjustment must be performed in the following cases:
• When the mirror base drive wire is replaced.
• When the lamp unit, or No. 2/3 mirror holder is replaced.
• When a copy as shown is made.
Lb
La
Paper exit
direction
Original
Copy
1) Set A3 (11" x 17") white paper on the original table as shown
below.
Place a little clearance from
the rear side original guide.
Glass holding plate
AR-235/275 ADJUSTMENTS - 5
A3 (11" x 17") white paper
Fit the paper edge and
the glass holding plate edge.
2) Open the original cover and make a normal (100%) copy.
• When a following copy is made.
3) Measure the width of the black background at the lead edge and at
the rear edge.
Original
Copy A
Copy B
1) Make an original for the adjustment.
Make test sheet by drawing parallel lines at 10mm from the both
ends of A3 (11" x 17") white paper as shown below. (These lines
must be correctly parallel to each other.)
Parallel line
Paper exit direction
Parallel line
10mm
10mm
10mm
10mm
La: Lead edge black background width
Lb: Rear edge black background width
If the width (La) of the black background at the lead edge is equal
that (Lb) at the rear edge, there is no need to execute the following
procedures of 4) – 7).
4) Loosen the mirror base drive pulley fixing screw on the front frame
side or on the rear frame side.
• When La < Lb
Turn the mirror base drive pulley on the front frame side in the
arrow direction A. (Do not move the mirror base drive pulley shaft.)
• When La > Lb
Turn the mirror base drive pulley on the rear frame side in the
arrow direction A. (Do not move the mirror base drive pulley shaft.)
White paper
2) Make a normal (100%) copy of the test sheet on A3 (11" x 17")
paper. (Fit the paper edge and the glass holding plate edge.)
3) Measure the distances (La, Lb, Lc, Ld) at the four corners as
shown below.
La
Lc
Rear side
A
B
Paper exit
direction
Front side
Lb
Ld
When La = Lb and Lc = Ld, no need to perform the procedures 4)
and 5).
5) Tighten the fixing screw of the mirror base drive pulley.
4) Move the mirror base B rail position up and down (in the arrow
direction) to adjust.
<Adjustment specification>
La = Lb
6) Execute the main scanning direction (FR) distortion balance
adjustment previously described in 2) again.
(9) Main scanning direction (FR direction) distortion
balance adjustment (Rail height adjustment)
When there is no skew copy in the mirror base scanning direction and
there is no horizontal error (right angle to the scanning direction), the
adjustment can be made by adjusting the No. 2/3 mirror base unit rail
height.
Before performing this adjustment, be sure to perform the horizontal
image distortion adjustment in the laser scanner section.
This adjustment must be performed in the following cases:
• When the mirror base wire is replaced.
• When the copy lamp unit and no. 2/3 mirror unit are replaced.
• When the mirror unit rail is replaced and moved.
AR-235/275 ADJUSTMENTS - 6
• When La > Lb
Shift the mirror base B rail upward by the half of the difference of
La–Lb.
• When La < Lb
Shift the mirror base B rail downward by the half of the difference
of Lb–La.
Example: When La = 12mm and Lb = 9mm, shift the mirror base
B rail upward by 1.5mm.
• When .E >.F
Shift the mirror base B rail downward by the half of the difference
of Lc–Ld.
• When Lc < Ld
When Lc < Ld, move the mirror base B on the paper feed side
upward.
∗ When moving the mirror base rail, hold the mirror base rail with
• Error in the auto correction mode
Copy quantity
display "– –"
Display
Content
The correction
value
calculated is
over 5%.
Paper jam
lamp ON
Reference line
scanning error
Major cause
• Improper position of reference
width line of the reference white
plate
• Improper installation of CCD unit
• Defective CCD
• No reference white plate
(11) Sub scanning direction (scanning direction)
magnification ratio adjustment (SIM 48-1-3)
a. OC mode in copying
Note: Execute the procedure after completion of SIM 48-1-3.
1) Put a scale on the original table as shown below, and make a normal (100%) copy.
your hand.
<Adjustment specification>
La = Lb, Lc = Ld
5) After completion of adjustment, manually turn the mirror base drive
pulley, scan the mirror base A and mirror base B fully, and check
that the mirror bases are not in contact with each other.
∗ If the mirror base rail is moved extremely, the mirror base may be in
contact with the frame or the original glass. Be careful to avoid this.
(10) Main scanning direction (FR direction) magnification
ratio adjustment (SIM 48-1)
Before performing this adjustment, be sure to check that the
CCD unit is properly installed.
2) Compare the scale image and the actual scale.
If necessary, perform the following adjustment procedures.
3) Execute SIM 48-1-3.
1) Put a scale on the original table as shown below.
4) Enter the set value and press the start key.
The set value is stored and a copy is made.
<Adjustment specification>
Adjustment
mode
Sub scanning
direction
magnification
ratio (OC mode)
Spec value
SIM
Set value
At normal:
±1.0%
48-13
Add 1:
0.05% increase
Reduce 1:
0.05% decrease
Setting
range
1 – 99
b. RSPF sub scanning direction magnification ratio
2) Execute SIM 48-1.
3) After warm-up, shading is performed and the current set value of
the main scanning direction magnification ratio is displayed on the
display section in 2 digits.
4) Select the mode and press the start key again.
Note: Before performing this adjustment, be sure to check that the
CCD unit is properly installed and that OC mode adjustment in
copying has been completed.
1) Put a scale on the original table as shown below, and make a normal (100%) copy to make a test chart.
5) Auto correction mode (SIM48-1-1)
The mirror unit moves to the shading position, and the reference
width of the reference white plate is scanned, and the correction
value is automatically calculated from that scanned value.
The correction value is displayed and a copy is made.
6) Compare the scale image and the actual scale.
If a fine adjustment is required, switch to the manual correction
mode with the magnification ratio display key and perform fine
adjustment.
7) Manual correction mode (SIM48-1-2)
Enter the set value and press the start key.
The correction value is stored and a copy is made.
Since the printed copy is used as a test chart, put the scale in
paralled with the edge lines.
<Adjustment specification>
2) Set the test chart on the SPF and make a normal (100%) copy.
3) Compare the scale image and the actual image.
If necessary, perform the following adjustment procedures.
A judgement must be made with 200mm width, and must not be
made with 100mm width.
Adjustment
mode
Main scanning
direction
magnification
ratio
Spec value
At normal:
±1.0%
SIM
48-1
Set value
Add 1: 0.1%
increase
Reduce 1: 0.1%
decrease
Setting
range
1 – 99
4) Execute SIM 48-1-4.
5) After warm-up, shading is performed.
The current front surface sub scanning direction magnification ratio
correction value is displayed in two digits on the display section.
AR-235/275 ADJUSTMENTS - 7
6) Enter the set value and press the start key.
The set value is stored and a copy is made.
<Adjustment specification>
7) Execute SIM 48-1-5.
The current back surface sub scanning direction magnification
ratio is displayed in two digits on the display section.
3) If the distance is outside the specified range, adjust the open/close
sensor attachment plate position as shown below.
OC (SPF) open/close position A: 125 – 225mm
8) Enter the set value and press the start key.
The set value is stored and a copy is made.
Distance < : Shift toward A.
Distance > : Shift toward B.
<Adjustment specification>
Adjustment
mode
Sub scanning
direction
magnification
ratio (SPF mode)
Spec value
SIM
Set value
At normal:
±1.0%
48-1-4
48-1-5
Add 1:
0.05% increase
Reduce 1:
0.05% decrease
Setting
range
1 – 99
A
(12) Off center adjustment (SPF mode)
Before performing this adjustment, be sure to check that the
paper off center is properly adjusted.
1) Place the center position adjustment test chart (sheet with a
straight line in the scan direction at the center) on the SPF.
B
2) Make a normal copy from the manual paper feed tray, and check
the printed copy with the test chart.
If any adjustment is required, perform the following procedure.
3) Execute SIM 50-12.
(14) Original sensor adjustment (SIM 41-2, 41-4)
4) After warm-up, shading is performed and the current set value of
the off center adjustment is displayed on the display section in 2
digits.
1) Set A3 (11" x 17") paper on the OC table.
(Keep the SPF (OC cover) open.)
5) Enter the set value and press the start key.
The set value is stored and a copy is made.
3) Keep A=125mm, and execute SIM 41-4. (Do not put paper on the
table.)
4) Check the reaction with SIM 41-1.
<Adjustment specification>
Adjustment
mode
Original off
center mode
(SPF mode)
2) Execute SIM 41-2.
Spec value
SIM
Set value
Single: Center
± 3.0mm
Duplex: Center
±3.5mm
50-12
Add 1: 0.1mm
shift to R side
Reduce 1: 0.1mm
shift to L side
Setting
range
1 – 99
(13) OC (SPF) open/close detection position adjustment
1) Execute SIM 41-3.
2) Gradually close the OC (SPF) from the full open position, and measure distance A when the display on the operation panel changes.
(See the figure below.)
(15) SPF white correction pixel position adjustment
(required in an SPF model when replacing the lens
unit) (SIM63-7)
1) Fully open the SPF.
2) Execute SIM 63-7.
3) When the operation panel displays "COMPLETE," the adjustment
is completed.
4) If the operation panel displays "ERROR," perform the following
measures.
• When the display is 0:
Check that the SPF is open.
Check that the lamp is ON. (If the lamp is OFF, check the MCU connector.)
Check that the CCD harness is properly inserted into the MCU connector.
• When the display is 281 or above:
Distance A = Table glass top - OC (SPF) handle rib
1) Remove the table glass.
2) Remove the dark box.
3) Slide the lens unit toward the front side and attach it, then execute SIM.
• When the display is 143 or below:
1) Remove the table glass.
2) Remove the dark box.
A
3) Slide the lens unit toward the rear side and attach it, then execute SIM.
F
AR-235/275 ADJUSTMENTS - 8
R
∗ When the lens unit is moved, execute the OC main scanning magni-
fication ratio auto adjustment, SIM 48-1-1, SIM48-3 and the SPF
original off-center adjustment.
∗ This adjustment is basically O.K. with SIM 63-7.
C. Image density (exposure) adjustment
(1) Copy mode (SIM46-2)
1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown
below.
Rear
Front
2) Place three or more sheets of A3 (11" x 17") paper on the test
chart.
3) Execute SIM 46-2.
4) After warm-up, shading is performed and the current set value of
the density (exposure) level is displayed on the display section in 2
digits.
For mode selection, use the [10-key].
5) Change the set value with the [10-key] to adjust the copy image
density.
6) Make a copy and check that the specification below is satisfied.
Note: Place originals in the rear reference, and the test chart in the
front reference when adjusting the exposure.
<Adjustment specification>
Density
mode
AUTO
Display
Lamp
AUTO
TEXT
TEXT
TEXT/
PHOTO
PHOTO
TEXT/
PHOTO
PHOTO
SUPER
PHOTO
TONER
SAVE
SUPER
PHOTO
AUTO (TS)
TEXT (TS)
TEXT
PHOTO (TS)
Exposure
level
–
3
3
3
3
3
3
3
Sharp Gray
Chart output
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
"3" is
copied.
Set value
If too bright,
increase the
quantity
displayed on
the copy
quantity
display.
If too dark,
decrease the
quantity
displayed on
the copy
quantity
display.
Setting
range
0 – 99
AR-235/275 ADJUSTMENTS - 9
[8] SIMULATION
1. Operating procedures and operations
Screen
Maginification
ratio selection
A. Basic operation
Procedure
Key operation
Execution
Key
CA
Interrupt
←, →
↓, ↑
OK
Back
CA
Interrupt
Back
Function
Cancel simulation
Sub code input screen appears.
Magnification ratio selection (1% increment)
Fixed magnification ratio setting
Shifts to the screen during operation.
Shifts to the number of times selection screen.
Cancel simulation
Sub code input screen appears.
Shifts to the magnification ratio setup menu.
1 Simulation mode selection
# → INTERRUPT → C → INTERRUPT
2 Main code selection
10-key (Input main code) → START
Load operation system with data setup
3 Sub code selection
10-key (Input sub code) → START
Screen
Key
Selection of
CA
the adjustment Interrupt
items
C
10-key
↓, ↑
OK
Adjustment
CA
value input
Interrupt
10-key
C
OK
Back
Execution
CA
Interrupt
Back
4
Selection of the mode and
item
5 Start simulation operation
Returns to the sub code
6 selection.
Simulation mode clear
10-key and ↑
↓
OK or START
INTERRUPT
CA
• Selection of the main code and the sub code is set with the [START]
key.
• There are two or more screens, the adjustment "Current page/Max.
page" is displayed. Press [↑] key (previous page) or [↓] key to select
a screen.
B. Simulation kinds and valid key functions
Single print system
Data screen system
Screen
Key
Selection of the CA
adjustment
Interrupt
items
C
10-key
↓, ↑
←, →
OK
START
Screen
Key
Counter display CA
Interrupt
↓, ↑
Function
Cancel simulation
Sub code input screen appears.
Page switch (in the case of multiple pages)
Sensor check system
Screen
Sensor check
screen
Key
CA
Interrupt
↓, ↑
Function
Cancel simulation
Sub code input screen appears.
Page switch (in the case of multiple pages)
Adjustment
value input
CA
C
Back
10-key
START
Execution
CA
Data setting system
Screen
Key
Selection of the CA
adjustment
Interrupt
items
C
10-key
↓, ↑
OK
Adjustment
CA
value input
Interrupt
10-key
C
OK
Back
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Adjustment item selection
Page switch (in the case of multiple pages)
The adjustment value input screen appears.
Cancel simulation
The sub code input screen appears.
Adjustment value input
Input value clear
Input final value
The adjustment item select screen appears.
C
Execution
Key
CA
Interrupt
C
10-key
↓, ↑
OK
CA
Interrupt
Back
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Load number selection
Page switch (in the case of multiple pages)
Shifts to the screen during operation.
Cancel simulation
Sub code input screen appears.
The load selection screen appears.
Screen
Initial stage
Execution
Key
CA
Interrupt
Selection of the
C
number of times
10-key
OK
Function
Simulation cancel
Sub code input screen appears.
Input value clear
Entry of the number of times
Shifts to the magnification ration selection screen.
Key
CA
Interrupt
C
10-key
OK
CA
Interrupt
Back
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Speed number selection
Shifts to the screen during operation.
Cancel simulation
Sub code input screen appears.
The intial screen appears.
Memory clear system
Screen
Counter
selection
Load operation system with magnification ratio setup
Screen
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Adjustment value input
Page switch (in the case of multiple pages)
Item switch
The adjustment value input screen appears.
Input value assured. → Print one page. → Shifts to
the execution screen.
Cancel simulation
Input value clear
The adjustment item selection screen appears.
Adjustment value input
Determination of the input value → Print of one page
→ shift to the execution screen.
After the single print, the copy conditions are cleared
and the adjustment value input screen appears.
After the single print, the copy conditions are not
cleared and the adjustment value input screen
appears.
Load operation system with data display
Load operation system
Screen
Load selection
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Adjustment item selection
Page switch (in the case of multiple pages)
The adjustment value input screen appears.
Cancel simulation
Sub code input screen appears.
Adjustment value input
Input value clear
Set value check
The adjustment item selection screen appears.
Cancel simulation
Sub code input screen appears.
The adjustment value input screen appears.
Check
Key
CA
Interrupt
C
10-key
OK
CA
Interrupt
OK
Back
Function
Cancel simulation
Sub code input screen appears.
Input value clear
Load number selection
The check screen appears.
Cancel simulation
Sub code input screen appears.
Clears and shifts to the counter select menu.
Not clears and shifts to the counter select menu.
Display check system
Screen
Display check
AR-235/275 SIMULATION - 1
Key
Function
CA
Cancel simulation
Interrupt Sub code input screen appears.
C. Simulation operation and procedure basic pattern
The pattern numbers in the table below are specified to the detailed procedures described below (for each simulation). Refer to them as necessary.
No.
1
2
3
Simulation operation and
procedure pattern
Used to set the
adjustment only.
Screen type
Adjustment value
input menu
Used to select the mode
and set the adjustment
value.
Mode selection menu
Used to set the
adjustment value and
output.
Adjustment value
input menu
Adjustment value
input menu
Execution menu
4
Used to select the mode
and set the adjustment
value and make an
output.
Mode selection menu
Adjustment value
input menu
Execution menu
5
1 sheet print mode
Mode selection menu
Adjustment value
input menu
6
Used to clear.
Initial menu
Confirmation menu
7
Used to select the item to
clear and execute
clearing.
Selection menu
8
Used to operate loads.
Initial menu
Execution menu
9
Used to select the load to
operate and operate the
load.
Selection menu
Used to set the number of
times, the magnification
ratio, and the original
size, and check the
operations.
(Scanner unit)
Input menu of the
number of times
Magnification ratio
and original size
setup menu
10
Confirmation menu
Execution menu
Execution menu
Operations and procedures common to every pattern
Enter the adjustment value with the 10-key and press the [OK] key.
If the input value is within the set range, it is stored. If it is outside the set range, it is not
set.
Select the mode with the 10-key and press the [OK] key, and the menu shifts to the
adjustment value input menu.
Enter the adjustment value with the 10-key and press the [OK] key.
If the input value is within the set range, it is stored. If it is outside the set range, it is not
set.
Pressing the [BACK] key returns to the mode selection menu.
Enter the adjustment value with the 10-key and press the [OK] key, and the menu goes
to the execution display.
If the input value is within the set range, it is stored. If it is outside the set range, it is not
set.
During execution, [EXEC] is highlighted.
Pressing the [BACK] key interrupts the operation and returns to the adjustment value
input menu.
Select the mode with the 10-key and press the [OK] key, and the menu shifts to the
adjustment value input menu.
Enter the adjustment value with the 10-key and press the [OK] key, and the menu goes
to the execution display.
If the input value is within the set range, it is stored. If it is outside the set range, it is not
set.
Pressing the [BACK] key returns to the mode selection menu.
During execution, [EXEC] is highlighted.
Pressing the [BACK] key interrupts the operation and returns to the adjustment value
input menu.
Enter the adjustment value with the 10-key and press [←] key to shift to the next mode,
and press [→] key to shift to the previous mode. Press the [START] key to make 1 sheet
print.
Pressing the [OK] key shifts to the adjustment value input menu.
If the input value is within the set range, it is stored. If it is outside the set range, it is not
set.
Press the adjustment value with the 10-key and press the [START] key to make 1 sheet
print.
After completion of print, the mode selection screen appears.
Pressing the [OK] key shifts to the confirmation display.
The confirmation message is displayed. Press the [OK] key to clear.
Pressing the [BACK] key returns to the initial menu without cleaning.
Select the counter to clear with the 10-key and press the [OK] key, and the menu goes to
the confirmation display.
The confirmation message is displayed. Press the [OK] key to clear.
Pressing the [BACK] key returns to the selection menu without cleaning.
Pressing the [OK] key shifts to the execution display.
During execution of load operation, [EXEC] is highlighted.
Pressing the [BACK] key interrupts the operation and returns to the initial menu.
The names of the loads which can be operated are displayed. Select one with the 10-key
and press the [OK] key, and the menu will go to the execution menu.
During execution of load operation, [EXEC] is highlighted.
Pressing the [BACK] key interrupts the operation and returns to the mode selection
menu.
Select the mode with the 10-key and press the [OK] key, and the menu shifts to the
magnification ratio and original size setup menu.
Select the magnification ratio with [↑][↓] keys. (Fixed magnification ratio)
Set the magnification ratio to a desired level with [←][→] keys. (1% increment)
Select the original size with the [PAPER SIZE] key.
Pressing the [OK] key shifts to the execution display.
Pressing the [BACK] key returns to the input menu of the number of times.
The scanner unit is moved at the speed corresponding to the set magnification ratio and
the original size.
During execution, [EXEC] is highlighted.
Pressing the [BACK] key interrupts the operation and returns to the setup menu of the
magnification ratio and the original size.
AR-235/275 SIMULATION - 2
No.
11
Simulation operation and
procedure pattern
Used to set the number of
times, the magnification
ratio, and the original
size, and check the
operations.
(SPF unit)
Screen type
Input menu of the
number of times
Magnification ratio
and original size
setup menu
Execution menu
12
Used to select the mode
and check the operations.
(Shifter)
Mode selection menu
Execution menu
Input menu
Operations and procedures common to every pattern
Select the mode with the 10-key and press the [OK] key, and the menu shifts to the
magnification ratio and original size setup menu.
Select the magnification ratio with [↑][↓] keys. (Fixed magnification ratio)
Set the magnification ratio to a desired level with [←][→] keys. (1% increment)
Select the original size with the [PAPER SIZE] key.
Select Single/Duplex with the [DUPLEX] key.
Pressing the [OK] key shifts to the execution display.
Pressing the [BACK] key returns to the input menu of the number of times.
The SPF unit is moved at the speed corresponding to the set magnification ratio and the
original size.
During execution, [EXEC] is highlighted.
Pressing the [BACK] key interrupts the operation and returns to the setup menu of the
magnification ratio and the original size.
Select the mode with the 10-key and press the [OK] key.
When 1 is selected, the menu shifts to the execution menu. When 2 is selected, the
menu shifts to the input menu.
During execution, [EXEC] is highlighted.
Pressing the [BACK] key interrupts the operation and returns to the mode selection
menu.
Pressing [←] key shifts the position toward R side by the specified steps.
Pressing [→] key shifts the position toward F side by the specified steps.
Pressing [↑] key shifts the home position.
Pressing the [BACK] key returns to the mode selection menu.
2. Simulation code list
Code
Main
Sub
1
1
2
2
1
2
3
3
2
3
4
6
7
11
2
3
5
1
2
3
6
1
2
7
1
6
8
Code
Main
Sub
8
1
Function
Used to check the operation of the scanner unit
and its control circuit.
Used to check the operation of sensor and
detector in the scanning (read) section and the
related circuit.
Used to check the operation of the SPF unit and
the related circuit.
Used to check the operation of sensors and
detectors in the SPF unit and the related circuit.
Used to check the operation of the loads in the
SPF unit and the control circuits.
Used to check the operation of sensor and
detector in the finisher and the related circuit.
Used to check the operation of the load in the
finisher and the control circuit.
Used to adjust the finisher jogger position.
Used to adjust the offset tray operations.
Used to check the operation of the shifter.
Used to check the operation of sensor and
detector in the option tray and the related circuit.
Used to check the operation of the load in the
option tray and the control circuit.
Used to check the operation of the display, LCD in
the operation panel, and control circuit.
Used to check the operation of the heater lamp
and the control circuit.
Used to check the operation of the copy lamp and
the control circuit.
Used to check the oepration of the loads (clutches
and solenoids) in the paper transport system and
the control circuit.
Used to check the operation of each fan motor and
its control circuit.
Used to set the aging operation conditions.
Used to set the cycle of intermittent aging.
Used to set the display of the warm-up time.
2
3
10
11
12
13
14
15
9
1
4
5
10
0
14
0
16
17
21
0
0
1
AR-235/275 SIMULATION - 3
Function
Used to check and adjust the operation of the
developing bias voltage in each copy mode and
the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each copy
mode and the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each copy
mode and the control circuit.
Used to check and adjust the operation of the
developing bias voltage in each printer mode and
the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each printer
mode and the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each printer
mode and the control circuit.
Used to check and adjust the operation of the
developing bias voltage in FAX mode and the
control circuit.
Used to check and adjust the operation of the main
charger grid voltage (high mode) in FAX mode and
the control circuit.
Used to check and adjust the operation of the main
charger grid voltage (low mode) in FAX mode and
the control circuit.
Used to check and adjust the operation of the load
(motor) in the duplex section and the control
circuit.
Used to adjust the rotation speed of the duplex
motor.
Used to adjust the switch back time of the duplex
motor.
Used to check the operation of the toner motor and
its control circuit.
Used to cancel excluding the self-diag U2/PF
troubles.
Used to cancel the self-diag U2 trouble.
Used to cancel the self diag "PF" trouble.
Used to set the maintenance cycle.
Code
Main
Sub
22
1
2
3
4
5
7
8
9
10
11
12
24
19
1
2
3
4
5
6
7
9
25
10
15
1
2
26
1
2
3
5
6
10
12
Function
Used to check the counter value of each section.
Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing this
count value with the total counter value.)
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
Used to check the total trouble (self diag) history.
Used to check the ROM version of each unit
(section).
Used to display the key operator code
Used to check the number of use of the staple, the
SPF, and scanning.
Used to check the number of use of each paper
feed section. (the number of prints)
Used to check the system configulation.
FAX related counter display
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
Used to display the scanner mode counter.
Used to clear the misfeed counter, the misfeed
history, the trouble counter, and the trouble history.
(The counters are cleared after completion of
maintenance.)
Used to clear the number of use (the number of
prints) of each paper feed section.
Used to clear the number data of use of the staple,
the SPF and scanning.
Used to reset the maintenance counter.
Used to reset the developer counter. (The
developer counter of the DV unit which is installed
is reset.)
Used to reset the copy counter.
Used to clear the OPC drum (membrane
decrease) correction counter. (This simulation is
executed when the OPC drum is replaced.
Used to clear the printer print counter. (The
counter is cleared after completion of
maintenance.)
FAX related counter clear
Used to clear the scanner mode counter.
Used to check the operation of the main drive
(excluding the scanner section) amd to check the
operation of the toner concentration sensor. (The
toner concentration sensor output can be
monitored.)
Used to make the initial setting of toner
concentration when replacing developer.
Used to set options. (This simulation is used to
make option setting when an option is installed.)
Used to detect the paper size.
Used to set the specifications of the auditor.
Setting must be made depending on the use
condition of the auditor.
Used to set the count mode of the total counter
and the maintenance counter.
Used to set the specifications depending on the
destination.
Used to enter the Software Key for the Network
Scanner. (Setup is allowed only when the PCL
board is installed.
Used to input the Software Key for E-MAIL RIC.
Code
Main
Sub
26
14
18
20
22
30
35
36
37
38
46
50
54
57
60
27
1
30
5
1
2
40
1
2
3
41
1
2
3
4
43
1
44
10
1
AR-235/275 SIMULATION - 4
34
35
40
Function
Used to input the Software Key for the PS
extention kit.
Used to set enable/disable of toner save operation.
Used to set the job separator paper exit mode.
Used to set the specification (language display) for
the destination.
Used to set the operation mode for CE mark.
Used to set the mode of trouble memory.
Used to set whether to stop when the maintenance
life is reached.
Used to set whether to stop when the developer
life is reached.
Used to set whether to stop when the drum life is
reached.
Used to set whether to meet with the output
direction of images regardless of the mode when
installing the finisher.
Used to set whether to use the black/white reverse
function.
Used to set the PWM duty (brightness) at the
center value of the LCD contrast.
Used to set the model code.
Used to set enable/disable of the FAX mode key
when FAX is not installed. (When FAX is installed,
the FAX mode is enabled regardless of this setup.)
Used to set PC/MODEM communication trouble
(U7-00) detection Yes/No.
Used to enter the TAG No. of the copier.
Used to check the operation of sensors and
detectors in the sections other than the paper feed
section of the copier and the related circuit. (The
operation of sensors and detectors can be
monitored with the LCD.)
Used to check the operation of sensors and
detectors in the paper feed section and the related
circuits. (The operations of sensors and detectors
in the paper feed section can be monitored with
the LCD.)
Used to check the operation of the manual paper
feed tray paper size detector and the related
circuit. (The operation of the manual paper feed
tray paper size detector can be monitored with the
LCD.)
Used to adjust the manual paper feed tray paper
width detector detection level.
The AD conversion value of manual feed width
detection is displayed.
Used to check the document size detection photo
sensor.
Used to adjust the detection level of the document
size photo sensor.
Used to check the light reception level and the
detection level of the original size detection photo
sensor.
Used to adjust the detection level of OC 20
degrees.
Used to set the fusing temperature in each
operation mode.
Used to set the paper feed cycle for postcard.
Used to make various setups in each mode of
process control.
Used to adjust the transfer current value.
Correction temperature setup when correcting the
ambient temperature.
Used to set the rotating time before toner supply.
Code
Main
Sub
46
2
7
9
10
11
12
13 to
16
18
19
48
20
30
1
2
3
50
8
9
10
1
5
6
8
9
10
12
51
1
2
8
61
63
1
1
7
64
1
65
5
Function
Used to adjust the copy exposure level.
Used to adjust individually the copy exposure
level. (Super photo)
Used to adjust individually the copy exposure
level. (Character)
Used to adjust individually the copy exposure
level. (Character/Photo)
Used to adjust individually the copy exposure
level. (Photo)
FAX exposure level adjustment (batch)
FAX exposure level adjustment (individual)
Used to adjust the copy contrast. (Inclination)
Used to change the image quality in the exposure
mode.
Used to correct SPF exprosure.
Used to set the AE limit.
Used to adjust the copy magnification ratio (main
scanning direction, sub scanning direction).
Used to adjust the scanner magnification ratio
(main/sub scanning direction).
Used to adjust the lead edge/sub scan
magnification ratio.
FAX magnification ratio adjustment (read)
FAX magnification ratio adjustment (print)
FAX auto reduction magnification ratio (print).
Used to adjust the copy lead edge position.
Used to adjust the print image position (top
margin) on the print paper in the print mode.
Used to adjust the print image position (top
margin) on print paper in the copy mode. (SPF/
RSPF)
FAX lead edge adjustment (read)
FAX lead edge adjustment (print)
Used to adjust the print image center position.
(Adjustment can be made for each paper feed
section.)
Used to adjust the print image center position.
(Adjustment can be made for each document
mode.)
Used to adjust the OPC drum separation pawl ON
time.
Used to adjust the contact pressure of paper onto
the resist roller in each section (copier paper feed
section, duplex paper feed section, SPF paper
feed section). (When the print image position
varies greatly for the paper or when a lot of paper
jam troubles occur, the adjustment is required.)
Used to set to disable the operation of the
separation pawl of the photoconductor drum.
Used to test the operation of the LSU.
Used to check the result of shading correction.
(The shading correction data are displayed.)
Used to adjust the SPF white correction start pixel
position automatically.
This adjustment is performed after the lens unit is
replaced.
Used to check the operation of the printer function
(auto print operation).
Used to check the operation panel.
Code
Main
Sub
66
1
2
3
4
6
7
8
10
11
13
67
17
21
22
30
32
34
37
38
41
50
51
52
53
11
14
17
18
20
Function
FAX related soft SW setting
Initial set for the value of the FAX soft SW
FAX PWB memory check
Signal send mode
Printing the confidential password
Image data print
Voice Message send
Image data memory clear
300bps signals send
Send test and adjustment of the dial pulse and
DTMF signal.
DTMF signal send
FAX information print
Handset sound volume adjustment
TEL/LIU state change recognition
Receive data check
Communication time measurement display
Speaker sound volume adjustment
Time setting/check
CI signal check
FAST SRAM clear
Signal detection check
Pseudo-ringer check
SRAM backup
Used to set the Select-IN signal.
Used to check write/comparison of flash programs.
Used to clear NVRAM.
Used to clear the data area for FLASH ROM
Network Scanner Application.
Used to check the network connection when a
scanner option is installed.
3. Details
1
1-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the scanner unit and its
control circuit.
Optical (Image scanning)
Operation
Operation/procedure (Pattern 10)
Enter the number, set the magnification ratio and the original size and
press the [OK] key, and the scanner unit will operate in a speed corresponding to the setup.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim1-1 SCAN CHECK
115%
A3
100%
86%
ZOOM <100%>
0
Sim1-1 SCAN CHECK
115%
A3
100%
86%
ZOOM <100%>
EXEC
Sim1-1 SCAN CHECK
115%
A3
100%
86%
ZOOM <100%>
EXEC
The fixed magnification ratio (25% to 400%) can be changed in 11
steps with [↑] [↓] keys.
(AB series) → 25 → 50 → 70 → 81 → 86 → 100 → 115 → 122 → 141 →
200 → 400
(Inch series) 25 → 50 → 64 → 77 → 95 → 100 → 121 → 129 → 141 →
200 → 400
The scan counter is displayed during execution.
AR-235/275 SIMULATION - 5
Magnification ratio
Default
Document size
Set number of times
25% to 400%
100%
Varies depending on the destination.
1 to 999 (0: Continuous operation)
The active sensors and detectors are highlighted.
Sim2-2 SENSOR CHECK
EMPS DLS1 DLS2
DWS1 DWS2 DWS3
FGOD DFD RDD
OPCLS
1-2
Operation test/check
Purpose
Used to check the operation of sensor and detector in
Function
(Purpose) the scanning (read) section and the related circuit.
Optical (Image scanning)
Section
Operation
Item
Operation/procedure
The status of sensors and detectors in the scanner section is displayed. The active sensors and detectors are highlighted.
Sim1-2 SENSOR CHECK
MHPS
EMPS
DLS1
DLS2
DWS1
DWS2
DWS3
FGOD
DFD
RDD
OPCLS
Empty sensor
Tray length sensor (small)
Tray length sensor (large)
Tray width sensor (small)
Tray width sensor (middle)
Tray width sensor (large)
Paper feed cover sensor
Document entry detection sensor
Document exit sensor
Book sensor
Note: Executable only when the SPF/RSPF is installed.
2-3
MHPS
Mirror home position sensor
Purpose
Function
(Purpose)
Section
Item
2
Operation/procedure (Pattern 9)
2-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the loads in the SPF
unit and the control circuits.
SPF
Operation
Operation test/check
Used to check the operation of the SPF unit and the
related circuit.
SPF
Operation
Operation/procedure (Pattern 11)
Set a document on the APF paper feed tray, and fix it with tape.
Enter the number, set the magnification ratio and the original size and
press the [OK] key, and the SPF unit will operate in a speed corresponding to the setup.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim2-1 SPF AGING
115%
A3 1SIDE
100%
2SIDE
86%
ZOOM <100%>
0
Sim2-1 SPF AGING
115%
A3 1SIDE
100%
2SIDE
86%
ZOOM <100%>
EXEC
Sim2-1 SPF AGING
115%
A3 1SIDE
100%
2SIDE
86%
ZOOM <100%>
EXEC
The magnification ratio can be selected in the range of 50% – 200% in
9 steps with ↑ ↓ keys.
(AB series) 50 → 70 → 81 → 86 → 100 → 115 → 122 → 141 → 200
(Inch series) 50 → 64 → 77 → 95 → 100 → 121 → 129 → 141 → 200
The names of the loads which can be operated are displayed. Select
the load to be checked with the 10-key.
(Initial screen)
(Executing screen)
Sim2-3 OUTPUT CHECK
1:DTM-F 4:CLH
2:DTM-R 5:GSOL
3:DFSOL 6:RSOL
EXEC
2
1:DTM-F
2:DTM-R
3:DFSOL
4:CLH
5:GSOL
6:RSOL
Sim2-3 OUTPUT CHECK
1:DTM-F 4:CLH
2:DTM-R 5:GSOL
3:DFSOL 6:RSOL
EXEC
2
SPF motor forward rotation
SPF motor reverse rotation
SPF document pick-up solenoid
SPF document exit transport clutch
RSPF document exit gate solenoid
RSPF document pressure solenoid
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
Note: Executable only when the SPF/RSPF is installed.
3
The scan counter is displayed during execution.
Magnification ratio
Default
Document size
Single/duplex
Set number of times
50% to 200%
100%
Varies depending on the destination.
Selectable only when RSPF is installed, fixed
(single) for SPF.
1 to 999 (0: Continuous operation)
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of sensor and detector in
the finisher and the related circuit.
Sorter/Finisher
Operation
Operation/procedure
Note: Executable only when the SPF/RSPF is installed.
Used to display the operations of sensors and detectors in the finisher
section.
2-2
Purpose
Function
(Purpose)
Section
Item
3-2
Operation test/check
Used to check the operation of sensors and detectors
in the SPF unit and the related circuit.
SPF
Operation
The active sensors and detectors are highlighted.
Sim3-2 SENSOR 1/2
INPD FWPS JGHP1
JGHP2 JGPD T1OD
T1PF PGOP T2OD
OFHP T2UP T2DN
Operation/procedure
The operations of sensors and detectors in the SPFsection are displayed.
AR-235/275 SIMULATION - 6
INPD
FWPS
JGHP1
JGHP2
JGPD
T1OD
T1PF
PGOP
T2OD
OFHP
T2UP
T2DN
JGDSW
EVRE
STHP
READY
LSTS
NCTS
STND
T2PUD
Finisher paper entry sensor
Paper width sensor
Side guide plate HP sensor
Rear edge plate HP sensor
Tray paper empty sensor
1st tray exit sensor
1st tray paper full sensor
JAM processing PG open/close detection sensor
2nd tray transport sensor
Offset HP sensor
Tray position sensor (upper)
Tray position sensor (lower)
Tray jam processing interlock
Lift-up drive control sensor
Staple HP sensor
Self priming sensor
Staple empty sensor
Cartridge empty sensor
Staple supply cover open/close sensor
2nd tray upper surface sensor
3-6
Adjustment
Purpose
Used to adjust the finisher jogger position.
Function
(Purpose)
Sorter/Finisher
Section
Operation
Item
Operation/procedure (Pattern 4)
After the paper size is set, the side guide plate and the rear guide plate
are set.
Shifts to the specified paper size position.
(Initial screen)
(Input screen)
Sim3-6 JOGGER ADJ.
1:PAPER SIZE
2:JOGGER POS X
3:JOGGER POS Y
1
Note: Executable only when the finisher is installed.
3-3
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the load in the finisher
and the control circuit.
Sorter/Finisher
Operation
Operation/procedure (Pattern 9)
The names of the loads which can be operated are displayed. Select
the load to be checked with the key.
(Initial screen)
(Executing screen)
Sim3-3 OUTPUT CHECK
1:JGM1
4:FM-1200
2:JGM2
5:EVM
3:FM-600 6:OFM
1/3
EXEC
2:JOGGER POS X
3:JOGGER POS Y
EXEC [ 0- 99]
EXEC [ 0- 99]
50
Content
Paper size
(1:A3, 2:A4, 3:B4, 4:B5,
5:A4R, 6:WLT, 7:LT, 8:LG,
9:FC, 10:LTR, 11:8K,
12:16K)
Side guide plate
Rear edge guide plate
Setting
range
1-12
50
Default
1-99
50
Example: When the side guide plate value is adjusted in A3, the same
adjustment is made in A4. (Value 1 in the table)
Paper size
Side guide plate
adjustment value number
A3
A4
B4
B5
A4R
WLT
LT
LG
FC
LTR
8K
16K
1
1
3
3
5
2
2
4
4
4
6
6
Sim3-3 OUTPUT CHECK
7:STM
10:JGSL1
8:OGSLR 11:JGSL2
9:OGSLL 12:SHTSL
2/3
EXEC
8
Side guide plate drive motor
Rear edge plate drive motor
Finisher main motor (600dpi)
Finisher main motot (1200dpi)
Tray lift-up motor
Tray offset motor
Staple operation motor
Transport selection gate solenoid (R)
Transport selection gate solenoid (L)
Rear edge plate drive solenoid
Upper alignment plate drive solenoid
Shutter drive solenoid
Paper exit roller clutch
Paper holding solenoid
Sim3-6 JOGGER ADJ.
2:JOGGER POS X 50
There are 6 adjustment values for the side guide plate, and 12 for the
rear guide plate. The adjustment position is determined from the table
below according to the paper size.
During execution, [EXEC] is highlighted. Under this state, press the
[BACK] key to interrupt the operation.
1:JGM1
2:JGM2
3:FM-600
4:FM-1200
5:EVM
6:OFM
7:STM
8:OGSLR
9:OGSLL
10:JGSL1
11:JGSL2
12:SHTSL
13:T2SCL
14:STGSL
Sim3-6 JOGGER ADJ.
2:JOGGER POS X 50
Display items
1:PAPER SIZE
(Executing screen)
Adjustment value number
of the rear edge guide
plate
2
9
3
10
6
1
8
4
5
7
11
12
Note: Executable only when the finisher is installed.
3-7
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the offset tray operations.
Operation
Operation/procedure
The finisher main motor operates for 10sec, the staple motor 5 times,
the tray lift-up motor one reciprocating operation, other motors max. 20
reciprocating operations from the home position, the solenoid repeats
500msec ON and 500msec OFF 20 times.
The staple operation motor operates only when there is no cartridge
installed.
(Initial screen)
Sim3-7 OFFSET ADJ.
1:PAPER PUSH TMG 50
2:PAPER OUT DOWN 1
3:STAPLE UP
6
1/2
Note: Executable only when the finisher is installed.
AR-235/275 SIMULATION - 7
(Input/Selection screen) (Executing screen)
Sim3-7 OFFSET ADJ.
1:PAPER PUSH TMG 50
[ 34- 66]
50
Sim3-7 OFFSET ADJ.
5:OFFSET INI.POS 13
EXEC [ 0- 99]
13
Display items
1:PAPER PUSH TMG
2:PAPER OUT DOWN
3:STAPLE UP
4:STAPLE DOWN
5:OFFSET INI.POS
Content
Installation
range
34-66
Default
Paper holder
50
descending timing in
non-staple
Used to adjust the descending timing of the
paper holder lever before lift-up operation
after paper exit or offset operation. (The
paper holder lever prevents against paper
shift in paper top surface detection and paper
stacking .)
Tray descending
0-12
1
distance after nonstaple paper exit
Used to adjust the offset tray descending
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
Tray lift distance
0-12
6
before staple paper
exit
The height of the tray standby position in
stapling is changed for that in non-stapling to
improve stacking capacity in stapling. (The
relative distance for the height of the tray
standby position in non-stapling is set.)
Tray descending
0-12
6
distance after staple
paper exit
Used to adjust the offset tray descending
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
Offset tray shift
0-99
13
position adjustment
Used to shift the offset tray to the shipment
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
(In the case of 0 - 94 (Shipment position: 13))
1) Initialize the offset tray normally.
2) The tray descends to the parameter position + 1 pulse position.
3) The tray lifts up to the specified parameter position.
(Disassembly position: 94 - 99)
1) The tray descends to the bottom.
* If there is some paper in the offset tray, the
tray cannot descend to the specified position. Check to insure that there is no paper
in the tray before execution.
Note: Executable only when the finisher is installed.
3-11
(Initial screen)
(Executing screen)
Sim3-11 SHIFTER CHK
1:F-R
2:HP CHECK
1
1:F-R
2:HP CHECK
[Selection 2]
Sim3-11 SHIFTER CHK
1:F-R
2:HP CHECK
EXEC
1
Reciprocating operation
Home position check
(Input/Selection screen)
Sim3-11 SHIFTER CHK
SFTHP
[ ]:R [ ]:HP [ ]:F
SFTHP:
Shifter home position (At detection, highlighted)
[←] key
[→] key
[↑] key
Shifts the position toward R side by the specified steps.
Shifts the position toward F side by the specified steps.
Shifts to the home position.
4
4-2
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of sensor and detector in
the option tray and the related circuit.
Paper feed
Operation
Operation/procedure
The operating states of the sensor and the detector are displayed.
The active sensors and detectors are highlighted.
Sim4-2 SENSOR CHECK
PED2 LUD2 PFD2 CD2
PED3 LUD3 PFD3 CD3
PED4 LUD4 PFD4 CD4
DSWR2 DSWR3 DSWR4
PED2
LUD2
PFD2
CD2
PED3
LUD3
PFD3
CD3
PED4
LUD4
PFD4
CD4
DSWR3
DSWR2
DSWR4
2nd cassette paper empty sensor
2nd cassette paper upper limit detection sensor
2nd cassette paper pass sensor
2nd cassette empty sensor
3rd cassette paper empty sensor
3rd cassette paper upper limit detection sensor
3rd cassette paper pass sensor
3rd cassette empty sensor
4th cassette paper empty sensor
4th cassette paper upper limit detection sensor
4th cassette paper pass sensor
4th cassette empty sensor
3rd cassette right door detection sensor
2nd cassette right door detection sensor
4th cassette right door detection sensor
Note: Execution is possible only when the option cassette is installed.
Purpose
Function
(Purpose)
Item
Operation test/check
Used to check the operation of the shifter.
Operation
Operation/procedure (Pattern 12)
[Selection 1]
Select with the 10-key.
4-3
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the load in the option
tray and the control circuit.
Paper feed
Operation
Operation/procedure (Pattern 9)
Select the load to check with the 10-key.
During execution of load operation, [EXEC] is highlighted.
Pressing the [BACK] key under this state interrupts the operation.
AR-235/275 SIMULATION - 8
(Initial screen)
(Initial screen)
(Executing screen)
Sim4-3 OUTPUT CHECK
1:LUM2
4:TRC2
2:CPFC2 5:DM
3:CPFS2 6:LUM3
1/2
EXEC
(Executing screen)
Sim5-2 HEATER LAMP
Sim4-3 OUTPUT CHECK
7:CPFC3 10:LUM4
8:CPFS3 11:CPFC4
9:TRC3
12:CPFS4
2/2
EXEC
8
PRESS OK KEY
2nd cassette lift-up motor
2nd cassette pick-up solenoid
2nd cassette paper feed clutch
2nd cassette transport roller clutch
2nd cassette paper transport motor (3rd cassette paper
transport motor)
6:LUM3
3rd cassette lift-up motor
7:CPFC3
3rd cassette pick-up solenoid
8:CPFS3
3rd cassette paper feed clutch
9:TRC3
3rd cassette transport roller clutch
10:LUM4
4th cassette lift-up motor
11:CPFC4 4th cassette pick-up solenoid
12:CPFS4 4th cassette paper feed clutch
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
1:LUM2
2:CPFC2
3:CPFS2
4:TRC2
5:DM
Sim5-2 HEATER LAMP
EXEC
EXEC
5-3
Operation test/check
Purpose
Used to check the operation of the copy lamp and the
Function
(Purpose) control circuit.
Optical (Image scanning)
Section
Operation
Item
Operation/procedure (Pattern 8)
Press the [OK] key.
The copy lamp lights up for 10 sec.
(Initial screen)
(Executing screen)
Sim5-3 COPY LAMP
Sim5-3 COPY LAMP
The lift-up motor operates only when the tray is opened. (20 times)
Note: Execution is possible only when the option cassette is installed.
PRESS OK KEY
EXEC
EXEC
When 10 sec passed, the copy lamp is turned OFF.
5
6
5-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the display, LCD in the
operation panel, and control circuit.
Operation (screen/operation)
Operation
Operation/procedure
The LCD is displayed as follows. (All LED’s are ON.)
(Initial screen)
With the upper half section highlighted,
Sim5-1 LCD/LED CHK.
contrast changes "Standard → MAX → MIN." in
every 2sec.
(6 sec later)
Sim5-1 LCD/LED CHK.
With the lower half section highlighted, contrast
changes "Standard → MAX → MIN." in every
2sec.
(6 sec later)
Sim5-1 LCD/LED CHK.
The back light changes in the sequence of
"OFF → Red → Yellow → Green" every 2
seconds.
5-2
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the heater lamp and the
control circuit.
Fixing (Fusing)
Operation
Operation/procedure (Pattern 8)
Press the [OK] key.
ON/OFF operation of the heater lamp is repeated 5 times in an interval
of 500ms.
6-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the loads (clutches and
solenoids) in the paper transport system and the
control circuit.
Paper transport (Discharge/Switchback/Transport)
Operation
Operation/procedure (Pattern 9)
The names of the loads which can be operated are displayed. Select
the load to be checked with the 10-key.
(Initial screen)
(Executing screen)
Sim6-1 OUTPUT CHECK
1:LUM1
4:MPFS
2:CPFC1 5:RRC
3:CPFS1 6:PSPS
1/2
EXEC
1:LUM1
2:CPFC1
3:CPFS1
4:MPFS
5:RRC
6:PSPS
7:OGS
8:LUM2
9:CPFC2
10:CPFS2
11:TRC2
12:LUM3
13:CPFC3
14:CPFS3
15:TRC3
16:LUM4
17:CPFC4
18:CPFS4
Sim6-1 OUTPUT CHECK
7:OGS
10:CPFS2
8:LUM2
11:TRC2
9:CPFC2
2/2
EXEC
8
1st cassette lift-up motor
1st cassette pick-up solenoid
1st cassette paper feed clutch
Manual feed pick-up solenoid
Resist roller clutch
Separation pawl solenoid
Paper exit gate switching solenoid
2nd cassette lift-up motor
2nd cassette pick-up solenoid
2nd cassette paper feed clutch
2nd cassette transport roller clutch
3rd cassette lift-up motor
3rd cassette pick-up solenoid
3rd cassette paper feed clutch
3rd cassette transport roller clutch
4th cassette lift-up motor
4th cassette pick-up solenoid
4th cassette paper feed clutch
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
The lift-up motor operates only when the tray is opened.
AR-235/275 SIMULATION - 9
7-6
6-2
Operation test/check
Purpose
Used to check the operation of each fan motor and its
Function
(Purpose) control circuit.
Others
Section
Operation
Item
Operation/procedure (Pattern 9)
The names of the loads which can be operated are displayed. Select
the load to be checked with the key.
(Initial screen)
(Executing screen)
Sim6-2 FAN MOTOR
1:VFM
2:DCFM&DCFM2
3:VFM&DCFM&DCFM2
EXEC
2
Sim6-2 FAN MOTOR
1:VFM
2:DCFM&DCFM2
3:VFM&DCFM&DCFM2
EXEC
2
3:VFM&DCFM&DCFM2
Enter the interval aging cycle time (sec) with the 10-key pad . Refer to
7-1.
Sim7-6 INTERVAL SET
AGING INTERVAL
3
[ 1-255]
The selected fan motor is highlighted and it rotates for 10sec.
1:VFM
2:DCFM&DCFM2
Setting/Operation test/check
Purpose
Used to set the cycle of intermittent aging.
Function
(Purpose)
Operation
Item
Operation/procedure (Pattern 1)
Only the fusing fan operates
Power cooling fan, power cooling fan 2
operations
Fusing fan, power cooling fan, and power
cooling fan 2 are operated at the same time.
Setting range
Default
3
1-255
3
7-8
Purpose
Function
(Purpose)
Item
Setting/Operation test/check
Used to set the display of the warm-up time.
Operation
Operation/procedure
7
Warm-up starts by the cover open/close.
(Can be performed repeatedly by open/close of the cover.)
The warm-up time is counted up and displayed in the unit of sec.
7-1
(Initial screen)
Purpose
Function
(Purpose)
Item
Setting/Operation test/check
Used to set the aging operation conditions.
(Executing screen)
Sim7-8 WARM UP TIME
PLEASE COVER
OPEN AND CLOSE
Sim7-8 WARM UP TIME
WARMING UP,
PLEASE WAIT.
Operation
1
Operation/procedure
Select with the 10-key.
4:INTERVL
5:WARMUP
6:DV CHK.
Sim7-8 WARM UP TIME
PLEASE COVER
OPEN AND CLOSE
WARM UP COMPLETED.
10
If the [CA] key is pressed at this time, count-up is interrupted to terminate the simulation. (However, warm-up is continued.)
Sim7-1 AGING SET.
1:AGING 4:INTERVL
2:MISFEED 5:WARMUP
3:FUSING 6:DV CHK.
2
1:AGING
2:MISFEED
3:FUSING
(Initial screen after completion)
After completion of warming up, "WARM UP COMPLETED" is displayed and the control returns to the initial screen.
Aging enable/disable setting
Jam detection enable/disable setting
Fusing operation enable/disable setting
The fusing temperature is not controlled. The heater is
not turned ON.
Intermittent setting (Valid only when set to AGING.)
Warm-up save setting
The machine goes into the ready state only by
shading, disregarding fusing and process control.
After going into the ready state, normal control is
performed.
Developing unit detection enable/disable setting
Press [CA] key, and the simulation will be terminated and copying will
be made with the set contents.
When selected without setup, the selected value is registered and
highlighted. When selected with previous setup, the previous setup is
canceled and it is displayed normally.
This setting is canceled by power OFF.
Note: In SIM 7-1, pressing [CA] key terminates the simulation and the
machine enters the aging mode without resetting. Therefore, to
perform "4. Intermittent setup," the intermittent cycle must be set
with SIM 7-6 in advance.
Reset is not performed when the machine enters the aging
mode.
8
8-1
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the
developing bias voltage in each copy mode and the
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Developer/Toner hopper
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-1 DV BIAS
1:AE
2:TEXT
3:TEXT/PHOTO
1/2
AR-235/275 SIMULATION - 10
COPY
426
450
450
Sim8-1 DV BIAS COPY
5:SUPER PHOTO 400
Sim8-1 DV BIAS COPY
5:SUPER PHOTO 400
EXEC [200-550] 400
EXEC [200-550] 400
Display items
Installation
range
200-550
Content
Default
1:AE
AE (∗)
426 (–426V)
2:TEXT
Character
450 (–450V)
3:TEXT/PHOTO
Character/Photo
450 (–450V)
4:PHOTO
Photo
450 (–450V)
5:SUPER PHOTO Super photo
400 (–400V)
6:TONER SAVE
Toner save
376 (–376V)
(∗) Linked with the destinations of SIM 26-6.
Linked with the auto exposure mode of SIM 46-19-1.
The minimum increment is 2V.
The result of (Set value – 199) / 2 is stored in the EEPROM.
When reading a value from the EEPROM, the value of (EEP value *2)
+ 200 is used as the set value.
Therefore, the set value entered must be an even number. If an odd
number is entered the entered odd number + 1 is displayed after
pressing [OK] key.
8-3
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each copy mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Section
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
Purpose
Function
(Purpose)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of –25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-3 MHV(L) COPY
1:AE
3
2:TEXT
5
3:TEXT/PHOTO
5
1/2
Sim8-3 MHV(L) COPY
5:SUPER PHOTO
3
Sim8-3 MHV(L) COPY
5:SUPER PHOTO
3
EXEC [ 1- 8]
EXEC [ 1- 8]
3
3
8-2
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each copy mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of –25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-2 MHV(H) COPY
1:AE
3
2:TEXT
5
3:TEXT/PHOTO
5
1/2
Display items
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
Sim8-2 MHV(H) COPY
5:SUPER PHOTO
3
Sim8-2 MHV(H) COPY
5:SUPER PHOTO
3
EXEC [ 1- 8]
EXEC [ 1- 8]
Content
AE (∗)
Character
Character/Photo
Photo
Super photo
Toner save
3
Setting
range
1-8
3
Default
4 (–555V)
5 (–580V)
5 (–580V)
5 (–580V)
3 (–530V)
2 (–505V)
(∗) Linked with the destinations of SIM 26-6.
Linked with the auto exposure mode of SIM 46-19-1.
NO.
1
2
3
4
5
6
7
8
Set value
480
505
530
555
580
605
630
655
Grid High
–480V
–505V
–530V
–555V
–580V
–605V
–630V
–655V
Display items
Content
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:TONER SAVE
AE (∗)
Character
Character/Photo
Photo
Super photo
Toner save
Setting
range
1-8
Default
4 (–425V)
5 (–450V)
5 (–450V)
5 (–450V)
3 (–400V)
2 (–375V)
(∗) Linked with the destinations of SIM 26-6.
Linked with the auto exposure mode of SIM 46-19-1.
NO.
1
2
3
4
5
6
7
8
Set value
480
505
530
555
580
605
630
655
Grid High
–480V
–505V
–530V
–555V
–580V
–605V
–630V
–655V
Grid Low
–350V
–375V
–400V
–425V
–450V
–475V
–500V
–525V
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.
8-10
Grid Low
–350V
–375V
–400V
–425V
–450V
–475V
–500V
–525V
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the
developing bias voltage in each printer mode and the
control circuit.
Image process (Photoconductor/Developping/
Transfer/Cleaning)
Developer/Toner hopper
Operation/procedure (Pattern 4)
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-10 DV BIAS
1:DENS1(600)
2:DENS2(600)
3:DENS3(600)
1/4
AR-235/275 SIMULATION - 11
PRT
400
450
450
Sim8-10 DV BIAS PRT
5:DENS5(600)
500
Sim8-10 DV BIAS PRT
5:DENS5(600)
500
EXEC [200-550] 500
EXEC [200-550] 500
Display items
Installation
range
200-550
Content
Default
1:DENS1(600)
Density 1 (600dpi)
400 (–400V)
2:DENS2(600)
Density 2 (600dpi)
450 (–450V)
3:DENS3(600)
Density 3 (600dpi)
450 (–450V)
4:DENS4(600)
Density 4 (600dpi)
450 (–450V)
5:DENS5(600)
Density 5 (600dpi)
500 (–500V)
6:TS(600)
Toner save (600dpi)
350 (–350V)
7:DENS1(1200)
Density 1 (1200dpi)
300 (–300V)
8:DENS2(1200)
Density 2 (1200dpi)
350 (–350V)
9:DENS3(1200)
Density 3 (1200dpi)
376 (–376V)
10:DENS4(1200) Density 4 (1200dpi)
426 (–426V)
11:DENS5(1200) Density 5 (1200dpi)
500 (–500V)
The minimum increment is 2V.
The result of (Set value – 199) / 2 is stored in the EEPROM.
When reading a value from the EEPROM, the value of (EEP value *2)
+ 200 is used as the set value.
Therefore, the set value entered must be an even number. If an odd
number is entered the entered odd number + 1 is displayed after
pressing [OK] key.
8-11
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each printer mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of –25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-11 MHV(H) PRT
1:DENS1(600)
3
2:DENS2(600)
5
3:DENS3(600)
5
1/4
Sim8-11 MHV(H) PRT
5:DENS5(600)
7
Sim8-11 MHV(H) PRT
5:DENS5(600)
7
EXEC [ 1- 8]
EXEC [ 1- 8]
Display items
Content
1:DENS1(600)
2:DENS2(600)
3:DENS3(600)
4:DENS4(600)
5:DENS5(600)
6:TS(600)
7:DENS1(1200)
8:DENS2(1200)
9:DENS3(1200)
10:DENS4(1200)
11:DENS5(1200)
Density 1 (600dpi)
Density 2 (600dpi)
Density 3 (600dpi)
Density 4 (600dpi)
Density 5 (600dpi)
Toner save (600dpi)
Density 1 (1200dpi)
Density 2 (1200dpi)
Density 3 (1200dpi)
Density 4 (1200dpi)
Density 5 (1200dpi)
NO.
1
2
3
4
5
6
7
8
Grid High
–480V
–505V
–530V
–555V
–580V
–605V
–630V
–655V
Set value
480
505
530
555
580
605
630
655
7
Installation
range
1-8
7
Default
5 (–580V)
5 (–580V)
5 (–580V)
5 (–580V)
7 (–630V)
3 (–530V)
1 (–480V)
3 (–530V)
4 (–555V)
5 (–580V)
7 (–630V)
Grid Low
–350V
–375V
–400V
–425V
–450V
–475V
–500V
–525V
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.
8-12
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each printer mode
and the control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 4)
After selecting the mode, enter the adjustment value and press the
[OK] key, and output will be made for 30sec.
The input value is in the increment of –25V.
(Initial screen)
(Input/Selection screen) (Executing screen)
Sim8-12 MHV(L) PRT
1:DENS1(600)
3
2:DENS2(600)
5
3:DENS3(600)
5
1/4
Display items
Sim8-12 MHV(L) PRT
5:DENS5(600)
7
Sim8-12 MHV(L) PRT
5:DENS5(600)
7
EXEC [ 1- 8]
EXEC [ 1- 8]
Content
1:DENS1(600)
2:DENS2(600)
3:DENS3(600)
4:DENS4(600)
5:DENS5(600)
6:TS(600)
7:DENS1(1200)
8:DENS2(1200)
9:DENS3(1200)
10:DENS4(1200)
11:DENS5(1200)
Density 1 (600dpi)
Density 2 (600dpi)
Density 3 (600dpi)
Density 4 (600dpi)
Density 5 (600dpi)
Toner save (600dpi)
Density 1 (1200dpi)
Density 2 (1200dpi)
Density 3 (1200dpi)
Density 4 (1200dpi)
Density 5 (1200dpi)
NO.
1
2
3
4
5
6
7
8
Grid High
–480V
–505V
–530V
–555V
–580V
–605V
–630V
–655V
Set value
480
505
530
555
580
605
630
655
7
Installation
range
1-8
7
Default
5 (–450V)
5 (–450V)
5 (–450V)
5 (–450V)
7 (–500V)
3 (–400V)
1 (–350V)
3 (–400V)
4 (–425V)
5 (–450V)
7 (–500V)
Grid Low
–350V
–375V
–400V
–425V
–450V
–475V
–500V
–525V
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.
8-13
Purpose
Function
(Purpose)
Section
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
Adjustment/Operation test/check
Used to check and adjust the operation of the
developing bias voltage in FAX mode and the control
circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Developer/Toner hopper
Operation/procedure (Pattern 3)
Enter the adjustment value and press the [OK] key, and output operation is performed for 30sec.
AR-235/275 SIMULATION - 12
(Initial screen)
(Initial screen)
(Executing screen)
(Executing screen)
Sim8-13 DV BIAS FAX
FAX
426
Sim8-13 DV BIAS FAX
FAX
426
Sim8-15 MHV(L) FAX
FAX
5
Sim8-15 MHV(L) FAX
FAX
5
EXEC [200-550] 4260
EXEC [200-550] 426
EXEC [ 1- 8]
5
EXEC [ 1- 8]
Setting range
Default
1-8
5
Setting range 200-550
Default
426
The minimum increment is 2V.
The result of (Set value – 199) / 2 is stored in the EEPROM.
When reading a value from the EEPROM, the value of (EEP value *2)
+ 200 is used as the set value.
Therefore, the set value entered must be an even number. If an odd
number is entered the entered odd number + 1 is displayed after
pressing [OK] key.
8-14
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (high mode) in FAX mode and the
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 3)
Enter the adjustment value and press the [OK] key, and output operation is performed for 30sec.
(Initial screen)
(Executing screen)
Sim8-14 MHV(H) FAX
FAX
5
Sim8-14 MHV(H) FAX
FAX
5
EXEC [ 1- 8]
5
EXEC [ 1- 8]
Setting range
Default
1-8
5
5
NO.
Set value
Grid High
Grid Low
1
480
–480V
–350V
2
505
–505V
–375V
3
530
–530V
–400V
4
555
–555V
–425V
5
580
–580V
–450V
6
605
–605V
–475V
7
630
–630V
–500V
8
655
–655V
–525V
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.
9
9-1
Purpose
Function
(Purpose)
Section
Item
5
Operation test/check
Used to check and adjust the operation of the load
(motor) in the duplex section and the control circuit.
Duplex
Operation
Operation/procedure (Pattern 9)
NO.
1
2
3
4
5
6
7
8
Set value
480
505
530
555
580
605
630
655
Grid High
–480V
–505V
–530V
–555V
–580V
–605V
–630V
–655V
Select with the 10-key and operate for 30 seconds.
(Initial screen)
(Executing screen)
Grid Low
–350V
–375V
–400V
–425V
–450V
–475V
–500V
–525V
Sim9-1 MOTOR CHECK
1:DMF600 4:DMR1200
2:DMF1200
3:DMR600
EXEC
2
*1. The negative value of the set value corresponds to the grid high
output voltage.
*2. The set values can be selected from the above 8 patterns only.
*3. The selected pattern determines the grid high voltage and the grid
low voltage.
If, for example, the grid high voltage is set to –480V (pattern 1), the
grid low voltage is –350V.
8-15
Purpose
Function
(Purpose)
Section
Adjustment/Operation test/check
Used to check and adjust the operation of the main
charger grid voltage (low mode) in FAX mode and the
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Photo conductor
Operation/procedure (Pattern 3)
Enter the adjustment value and press the [OK] key, and output operation is performed for 30sec.
1:DMF600
2:DMF1200
3:DMR600
4:DMR1200
Sim9-1 MOTOR CHECK
1:DMF600 4:DMR1200
2:DMF1200
3:DMR600
EXEC
2
Duplex motor forward rotation (600dpi)
Duplex motor forward rotation (1200dpi)
Duplex motor reverse rotation (600dpi)
Duplex motor reverse rotation (1200dpi)
9-4
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to adjust the rotation speed of the duplex motor.
Duplex
Operation
Operation/procedure (Pattern 1)
Set the rotation speed of the duplex motor.
Sim9-4 MOTOR SPEED
MOTOR SPEED
3
[ 1- 13]
Setting range
Default
AR-235/275 SIMULATION - 13
3
1-13
3
9-5
16
Adjustment
Purpose
Used to adjust the switch back time of the duplex
Function
(Purpose) motor.
Operation/procedure (Pattern 2)
Set the switch back time of the duplex motor.
(Initial screen)
(Input screen)
Sim9-5 SW BACK TIME
1:600dpi
50
2:1200dpi
50
1
Display items
1:600dpi
2:1200dpi
Sim9-5 SW BACK TIME
1:600dpi
50
16-0
Clear/Cancel (Trouble etc.)
Purpose
Used to cancel the self-diag U2 trouble.
Function
(Purpose)
Trouble
Error
Item
Operation/procedure (Pattern 6)
When the [OK] key is pressed, the trouble is canceled.
(Initial screen)
(Process check screen)
[ 18- 76]
Installation range
18-76
50
Default
50
50
10
Sim16 TROUBLE CLEAR
U2 TROUBLE CLEAR
Sim16 TROUBLE CLEAR
U2 TROUBLE CLEAR
PRESS OK KEY
ARE YOU SURE?
17
10-0
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the toner motor and its
control circuit.
Image process (Photoconductor/Developping/Transfer/
Cleaning)
Developer/Toner hopper
Operation
Operation/procedure (Pattern 8)
Press the [OK] key and operate the toner motor for 30 sec.
Pressing the [INTERRUPT] key interrupts the operation, and the display returns to the main code entry screen.
(Initial screen)
(Executing screen)
Sim10 TONER MOTOR
PRESS OK KEY
17-0
Purpose
Function
(Purpose)
Item
Cancel (Trouble, etc)
Used to cancel the self diag "PF" trouble.
Trouble
Error
Operation/Procedure (Pattern 6)
When the [OK] key is pressed, the trouble is canceled.
(Initial screen)
(Execution check screen)
Sim17 TROUBLE CLEAR
PF TROUBLE CLEAR
Sim17 TROUBLE CLEAR
PF TROUBLE CLEAR
PRESS OK KEY
ARE YOU SURE?
Sim10 TONER MOTOR
EXEC
21
EXEC
21-1
Purpose
Function
(Purpose)
Item
14
14-0
Purpose
Function
(Purpose)
Item
Clear/Cancel (Trouble etc.)
Used to cancel excluding the self-diag U2/PF troubles.
Trouble
Error
Operation/procedure (Pattern 6)
When the [OK] key is pressed, the trouble is canceled.
(Initial screen)
(Process check screen)
Sim14 TROUBLE CLEAR
TROUBLE CLEAR
(WITHOUT U2,PF)
Sim14 TROUBLE CLEAR
TROUBLE CLEAR
(WITHOUT U2,PF)
PRESS OK KEY
ARE YOU SURE?
Setting
Used to set the maintenance cycle.
Specifications
Counter
Operation/procedure (Pattern 1)
Enter the adjustment value and press the [OK] key.
Sim21-1 CYCLE SET.
MAINTE CYCLE
0
(0:5K 1:12.5K
2:25K 3:50K 4:FREE)
[ 0- 4]
0
Item
0
1
2
3
4
Content
5K
12.5K
25K
50K
FREE
AR-235/275 SIMULATION - 14
Setting range
0-4
Default
3
22
22-1
Adjustment/setting/operation data output/check
(display/print)
Used to check the counter value of each section.
Purpose
Function
(Purpose)
Counter
Item
Operation/procedure
Counter is displayed.
Sim22-1
TOTAL
MAINTE
DEVE
DRUM
COUNTER 1/3
: nnnnnnn
: nnnnnnn
: nnnnnnn
: nnnnnnn
Total
Maintenance
Developer counter
Drum counter
Copy counter
Printer counter
TOTAL
MAINTE
DEVE
DRUM
COPY
PRINTER
IMC
DUPLEX
IMC counter
Duplex counter
OTHERS
FAX SEND
FAX RCV
The other counters
FAX Send counter
FAX receive counter
22-2
Purpose
Function
(Purpose)
Item
Adjustment/setting/operation data output/check
(display/print)
Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is considerably
great, it is judged as necessary for repair. The misfeed
rate is obtained by dividing this count value with the
total counter value.)
Trouble
Operation/procedure
Counter data is displayed.
Sim22-2
JAM
SPF JAM
TROUBLE
JAM/TROUBLE
: nnnnnnn
: nnnnnnn
: nnnnnnn
JAM
SPF JAM
TROUBLE
JAM counter
SPF JAM counter
Trouble counter
Function
(Purpose)
Item
Jam contents
1st cassette pick-up miss
2nd cassette pick-up miss
3rd cassette pick-up miss
4th cassette pick-up miss
Multi manual feed pick-up miss
Paper-in sensor lead edge jam
Paper-in sensor rear edge jam
Paper-in sensor reverse jam
Duplex sensor lead edge jam
Duplex sensor rear edge jam
Upper stage paper exit lead edge jam
Upper stage paper exit rear edge jam
Lower stage paper exit lead edge jam
Lower stage paper exit rear edge jam
Abnormality between PS papers.
2nd paper pass lead edge jam
2nd paper pass rear edge jam
3rd paper pass lead edge jam
3rd paper pass rear edge jam
4th paper pass lead edge jam
4th paper pass rear edge jam
Duplex short scale error
Duplex long scale error
Duplex print remain (double feed) jam
Finisher paper entry jam
Finisher escape tray jam
Finisher offset tray jam
Finisher staple tray jam
22-4
Adjustment/setting/operation data output/check
(display/print)
Used to check the total trouble (self diag) history.
Purpose
Function
(Purpose)
Trouble
Item
Operation/procedure
The trouble error codes are displayed in the sequence of the latest one
first. Max. 40 items of information are stored. (Older ones are deleted
in sequence.) The machine condition can be estimated by this data.
Sim22-4 TROUBLE 1/4
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
XX-XX XX-XX XX-XX
22-3
Purpose
Display items
1ST_PICK
2ND_PICK
3RD_PICK
4TH_PICK
HND_PICK
PIN_TOP
PIN_END
PIN_DUP
DPX_TOP
DPX_END
UPO_TOP
UPO_END
LPO_TOP
LPO_END
PS
2ND_TOP
2ND_END
3RD_TOP
3RD_END
4TH_TOP
4TH_END
DPX_SHORT
DPX_LONG
DPX_DBLFD
FIN_PIN
FIN_ESC
FIN_OFST
FIN_STPL
Adjustment/setting/operation data output/check
(display/print)
Used to check the misfeed positions and the number of
misfeed at each position. (When the number of
misfeed is considerably great, it can be judged as
necessary for repair.)
Trouble
Mis-feed
Operation/procedure
The misfeed history is displayed in the sequence of recentness by the
name of sensors and detectors. Max. 40 items of information can be
stored in memory. (The old ones are deleted sequentially.) The trouble
section may be determined by the data.
Sim22-3 JAM HIS.1/5
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
22-5
Purpose
Function
(Purpose)
Item
Adjustment/Setting/Check
Used to check the ROM version of each unit (section).
Software
Operation/procedure
ROM and CPU data of each section are displayed.
Sim22-5
S/N
MCU
IMC
OPE
ROM VER.1/2
:0000000000
:00.00
:00.00
:00.00
[Display example]
ROM version 1.250 → [1.25] (upto 2 decimal places)
The display of the protocol monitor and the soft SW follows this display.
S/N
MCU
IMC
OPE
AR-235/275 SIMULATION - 15
Machine serial number
Main Control Unit
IMC
Panel
PRINTER
NIC
FINISHER
FAX
PRINTER
NIC
FINISHER
FAX
22-7
Sim22-10 SYSTEM 1/4
SPEED : XXXXXXX
DF
: XXXXXXX
OUTPUT : XXXXXXX
CASETTE1: XXXXXXX
User data output/Check (Display/Print)
Purpose
Used to display the key operator code
Function
(Purpose)
Data
User data
Item
Operation/procedure
Key operetion code is displayed.
Sim22-7 KEY OPE
KEY OPE CODE: nnnnn
22-8
Purpose
Function
(Purpose)
Item
Adjustment/setting/operation data output/check
(display/print)
Used to check the number of use of the staple, the
SPF, and scanning.
Counter
Operation/procedure
SPF
SCAN
STAPLE
[ ]: Shows the product code in the list below.
ORG./STAPLE
: nnnnnnn
: nnnnnnn
: nnnnnnn
SPF counter
Scan counter
Stapler counter
22-9
Purpose
Function
(Purpose)
Section
Item
Display items
23CPM/25CPM/27CPM
NONE/[1: SPF]/[2: RSPF]
NONE/[3: Finisher]/[4: Job separator]
NONE/[5: One-step paper feed unit]
NONE/[6: Two-step paper feed unit]
NONE/Expansion memory capacity (MB)
NONE/[7: PCL]
NONE/[8: PS3]
NONE/[9: NIC]
NONE/[10: SCANNER]
NONE/[11: FAX]
NONE/Memory capacity (MB)
NONE/[12: Handset]
NONE: "- - - - - - - - -" is displayed.
The data shows the use frequency of each section.
Sim22-8
SPF
SCAN
STAPLE
Display items
SPEED
DF
OUTPUT
CASETTE1
CASETTE2
IMC MEM
PCL
PS3
NIC
SCANNER
FAX
FAX MEM
HAND SET
Adjustment/setting/operation data output/check
(display/print)
Used to check the number of use of each paper feed
section. (the number of prints)
Paper feed
Counter
No.
Item
1
2
3
4
5
6
7
8
9
10
11
12
SPF
RSPF
Finisher
Job separator
1 tray paper feed unit
2 tray paper feed unit
PCL
PS3
NIC
SCANNER
FAX
Handset
Model code
AR model
DM model
AR-SP4
DM-SP2
AR-RP3
DM-RP1
AR-FN5
DM-FN1
AR-TR3
STANDARD
AR-D11 (*1)
DM-DE3 (*1)
AR-D12 (*1)
DE-DE4 (*)
AR-P11
STANDARD
AR-PK1
STANDARD
AR-NC5J
STANDARD
AR-NS2
DM-NS1
AR-FX4
DM-FX2
AR-HN4
–
*1: Installed quantity is displayed in ( ).
For the cassettes, only the option cassette is displayed.
Operation/procedure
The data shows the use frequency of each paper feed section.
Sim22-9
BYPASS
TRAY1
TRAY2
TRAY3
BYPASS
TRAY1
TRAY2
Purpose
Function
(Purpose)
FEED
1/2
: nnnnnnn
: nnnnnnn
: nnnnnnn
: nnnnnnn
Manual feed counter
Tray 1 counter
Tray 2 counter
Function
(Purpose)
Item
Adjustment/Setting/Check
FAX related counter display
Operation/procedure
TRAY3
TRAY4
Tray 3 counter
Tray 4 counter
The current counter value (number of send/receive pages) of the FAX
send/receive counter and the accumulated reception time and the print
counter are displayed.
Note: Executable only when the FAX is installed.
22-12
22-10
Purpose
22-11
Adjustment/setting/operation data output/check
(display/print)
Used to check the system configulation.
Specifications
Purpose
Function
(Purpose)
Option
Operation/procedure
The detected machine composition is displayed.
Section
Item
Adjustment/setting/operation data output/check
(display/print)
Used to check the misfeed positions and the number of
misfeed at each position. (When the number of
misfeed is considerably great, it can be judged as
necessary for repair.)
SPF
Trouble
Mis-feed
Operation/procedure
Fourty SPF JAM history datas are displayed sequentially from the latest.
AR-235/275 SIMULATION - 16
(Initial screen)
Sim22-12 SPF JAM1/5
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
XXXXXXX
Display items
PI_TOP
PI_END
PO_TOP
PO_END
JAM_REV
ORG_SHORT
ORG_LONG
1:BYPASS
2:TRAY1
3:TRAY2
Jam contents
SPF paper-in lead edge jam
SPF paper-in rear edge jam
SPF paper-out lead edge jam
SPF paper-out rear edge jam
SPF duplex reversion jam
SPF short scale error
SPF long scale error
Function
(Purpose)
Item
Sim24-2 COUNTER CLR
1:BYPASS 4:TRAY3
2:TRAY1 5:TRAY4
3:TRAY2
ARE YOU SURE?
2
Manual feed counter
Tray 1 counter
Tray 2 counter
4:TRAY3
5:TRAY4
Tray 3 counter
Tray 4 counter
24-3
Data clear
Purpose
Used to clear the number data of use of the staple, the
Function
(Purpose) SPF and scanning.
Counter
Item
Operation/procedure (Pattern 7)
22-19
Purpose
(Check screen)
Sim24-2 COUNTER CLR
1:BYPASS 4:TRAY3
2:TRAY1 5:TRAY4
3:TRAY2
2
Adjustment/setting/operation data output/check
(display/print)
Used to display the scanner mode counter.
Trouble
Operation/procedure
Counter data is displayed.
Clear the counters individually.
(Initial screen)
(Check screen)
Sim24-3 COUNTER CLR
1:SPF
2:SCAN
3:STAPLE
2
1:SPF
2:SCAN
3:STAPLE
Sim22-19 SCAN MODE
SCANMODE:nnnnnnnnn
Sim24-3 COUNTER CLR
1:SPF
2:SCAN
3:STAPLE
ARE YOU SURE?
2
SPF counter
Scan counter
Stapler counter
24-4
SCANMODE
Purpose
Function
(Purpose)
Item
Scanner mode counter
Data clear
Used to reset the maintenance counter.
Counter
24
Operation/procedure (Pattern 6)
24-1
Press the [OK] key.
(Initial screen)
Purpose
Function
(Purpose)
Item
Data clear
Used to clear the misfeed counter, the misfeed history,
the trouble counter, and the trouble history. (The
counters are cleared after completion of maintenance.)
Counter
Operation/procedure (Pattern 7)
Each counter is cleared individually. (The history of each counter is
deleted when clearing)
(Initial screen)
(Check screen)
Sim24-1 COUNTER CLR
1:JAM
2:SPF JAM
3:TROUBLE
2
1:JAM
2:SPF JAM
3:TROUBLE
Sim24-1 COUNTER CLR
1:JAM
2:SPF JAM
3:TROUBLE
ARE YOU SURE?
2
Clear the counters individually.
PRESS OK KEY
ARE YOU SURE?
24-5
Purpose
Function
(Purpose)
Section
Item
Data clear
Used to reset the developer counter. (The developer
counter of the DV unit which is installed is reset.)
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Developer/Toner hopper
Counter
Developer
Press the [OK] key.
(Initial screen)
Data clear
Used to clear the number of use (the number of prints)
of each paper feed section.
Paper feed
Counter
Operation/procedure (Pattern 7)
Sim24-4 COUNTER CLR
MAINTENANCE COUNTER
CLEAR
Operation/procedure (Pattern 6)
JAM counter/JAM history
SPF JAM counter/SPF JAM history
Trouble counter/Trouble history
24-2
Purpose
Function
(Purpose)
Section
Item
(Check screen)
Sim24-4 COUNTER CLR
MAINTENANCE COUNTER
CLEAR
(Check screen)
Sim24-5 COUNTER CLR
DEVELOPER COUNTER
CLEAR
Sim24-5 COUNTER CLR
DEVELOPER COUNTER
CLEAR
PRESS OK KEY
ARE YOU SURE?
24-6
Purpose
Function
(Purpose)
Item
AR-235/275 SIMULATION - 17
Data clear
Used to reset the copy counter.
Counter
Copier
Operation/procedure (Pattern 6)
Operation/procedure (Pattern 6)
Press the [OK] key.
(Initial screen)
Press the [OK] key.
(Check screen)
Sim24-6 COUNTER CLR
COPIES COUNTER
CLEAR
Sim24-6 COUNTER CLR
COPIES COUNTER
CLEAR
PRESS OK KEY
ARE YOU SURE?
The scanner mode counter and the number of send of the scanner are
cleared.
(Initial screen)
(Process check screen)
Sim24-15 COUNTERCLR
SCANNER MODE
COUNTER CLEAR
Sim24-15 COUNTERCLR
SCANNER MODE
COUNTER CLEAR
PRESS OK KEY
ARE YOU SURE?
24-7
Purpose
Function
(Purpose)
Section
Item
Data clear
Used to clear the OPC drum (membrane decrease)
correction counter. (This simulation is executed when
the OPC drum is replaced.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Photo conductor
Counter
Operation/procedure (Pattern 6)
Press the [OK] key.
(Initial screen)
(Check screen)
Sim24-7 COUNTER CLR
DRUM COUNTER CLEAR
Sim24-7 COUNTER CLR
DRUM COUNTER CLEAR
PRESS OK KEY
ARE YOU SURE?
25
25-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the main drive
(excluding the scanner section) and to check the
operation of the toner concentration sensor. (The toner
concentration sensor output can be monitored.)
DRIVE
Operation
Operation/procedure
The operation of the drive system is checked.
Toner density control sensor value is displayed.
Select the mode with the 10-key and press the [OK] key, and the main
motor will rotate and the toner concentration control sensor value will
be displayed.
24-9
Purpose
Function
(Purpose)
Section
Item
Data clear
Used to clear the printer print counter. (The counter is
cleared after completion of maintenance.)
Printer
Counter
Printer
Operation/procedure (Pattern 7)
After execution, interruption cannot be made for about 7 sec. ([CA] key,
[INTERRUPT] key, and [BACK] key are invalid.)
(Initial screen)
(Executing screen)
Sim25-1 MAIN MOTOR
1:600dpi
2:1200dpi
Clear the counters individually.
(Initial screen)
(Check screen)
Sim24-9 COUNTER CLR
1:PRINTER 4:OTHERS
2:IMC
3:DUPLEX
2
1:PRINTER
2:IMC
3:DUPLEX
4:OTHERS
EXEC
Sim24-9 COUNTER CLR
1:PRINTER 4:OTHERS
2:IMC
3:DUPLEX
ARE YOU SURE?
2
2
Sim25-1 MAIN MOTOR
1:600dpi
2:1200dpi
[128]
EXEC
2
25-2
Purpose
Function
(Purpose)
Section
Printer counter
IMC counter
DUPLEX counter
The other counters
Setting
Used to make the initial setting of toner concentration
when replacing developer.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Developer/Toner hopper
Operation/procedure
1) Open the cover.
24-10
Purpose
Function
(Purpose)
2) Power ON. (The mechanism cannot be initialized because the
cover is open.)
Adjustment/Setting/Check
FAX related counter clear
3) Install the developing unit with new developer in it.
4) Enter SIM 25-2.
Operation/procedure
5) Close the cover immediately before starting the operation.
The current counter value (number of send/receive pages) of the FAX
send/receive counter and the accumulated reception time and the print
counter are cleared to 0.
6) Press the [OK] key to start.
Note: Executable only when the FAX is installed.
When "EE-EU" or "EE-EL" after completion, an error display is shown.
24-15
EU error occurs when the finally calculated toner concentration reference value is 179 or greater.
Purpose
Function
(Purpose)
Item
Data clear
Used to clear the scanner mode counter.
Sampling is made 54 times every 600ms, and the average of the last
three times in the last 1.8sec of 3min is stored.
EL error occurs when the finally calculated toner concentration reference value is 77 or smaller.
Counter
AR-235/275 SIMULATION - 18
(Initial screen)
(Executing screen)
Sim25-2 AUTO DV ADJ
AUTO DEVE ADJUST
26
Sim25-2 AUTO DV ADJ
AUTO DEVE ADJUST
26-1
[128]
[CRUM-related error cancel procedure]
Setting
Purpose
Used to set options. (This simulation is used to make
Function
(Purpose) option setting when an option is installed.)
Specifications
Option
Item
Operation/procedure (Pattern 1)
• When “CRUM DEVICE ERROR” is displayed:
Set the job separator.
PRESS OK KEY
EXEC
EXEC
Note: After completion of execution, be sure to press the [CA] key to
cancel the simulation.
Error content:
Occurs in case of a communication error
between the machine and CRUM.
Cancel procedure: Reset with [CA] key and cancel with SIM 16.
• "CRUM DATA ERROR"
Error content:
CRUM identification error, CRUM model error,
CRUM type error, CRUM destination error
Cancel procedure: Install the CRUM which is satisfactory with the
machine setup, reset with the [CA] key, and
execute SIM 25-2 again.
• "DEVE UNIT NONE"
Error content:
Occurs when the developing unit is not installed
in an AR model.
Cancel procedure: It returns to the state before execution of auto
developer adjustment. It is canceled by the
operations of Cover open → Developing unit
installation → Cover close. Therefore, developer
adjustment is started by pressing [OK] key.
• "TONER UNIT NONE"
Error content:
Occurs when the CRUM is not installed in a DM
model.
Cancel procedure: It returns to the state before execution of auto
developer adjustment. It is canceled by the
operations of Cover open → CRUM installation →
Cover close. Therefore, developer adjustment is
started by pressing [OK] key.
• "EU ERROR"
Occurs when the toner concentration reference
value calculated in developer adjustment finally
is 179 or greater.
Cancel procedure: Reset with [CA] key and execute SIM 25-2 again.
Sim26-1 OPTION SET.
JOB SEPARATOR
0
(0:NONE
1:JOB SEPARATOR)
[ 0- 1]
0
Set value
0
1
Connection option
None (default)
Job separator provided.
26-2
Purpose
Function
(Purpose)
Section
Item
Setting
Used to detect the paper size.
Paper feed
Specifications
Operation/procedure (Pattern 2)
Used to set the automatic size detection.
Setting to detect B4/Legal as FC
0: B4 legal is detected as B4 legal.
1: B4 legal is detected as FC.
2:A4<->LT
This setup detects Letter as A4 in the inch series and
A4 as Letter in the AB series.
0: Detection disable
1: Detection valid
(Initial screen)
(Input screen)
1:B4/LG,FC
Sim26-2 SIZE SET
1:B4/LG,FC
0
2:A4<->LT
0
Sim26-2 SIZE SET
1:B4/LG,FC
0
(0:OFF 1:ON)
Error content:
• "EL ERROR"
Error content:
Occurs when the toner concentration reference
value calculated in developer adjustment finally
is 77 or smaller.
Cancel procedure: Reset with [CA] key and execute SIM 25-2 again.
Employed unit
Document
Document
table/SPF
1
Set value
0
1
Setup
Detection invalid
Detection valid
Remarks
Default
Detection size when 8.5" x 13" document/paper is used.
Destination
Document size
AB series (Japan)
FC (8.5” x 13”)
LG (8.5” x 14”)
B4
FC (8.5” x 13”)
LG (8.5” x 14”)
B4
FC (8.5” x 13”)
LG (8.5” x 14”)
B4
Set value
0
1
(Invalid)
(Valid)
B4
B4
B4
B4
B4
B4
B4
FC (8.5” x 13”)
B4
FC (8.5” x 13”)
B4
FC (8.5” x 13”)
LG (8.5” x 14”) FC (8.5” x 13”)
LG (8.5” x 14”) FC (8.5” x 13”)
WLT (11” x 17”) WLT (11” x 17”)
–
Set with key operations.
Inch series
Machine paper
feed cassette
Manual paper
feed tray
1
8.5" x 13" detection valid/invalid setup
AB series
Paper
[ 0- 1]
All destinations
Japan (AB series)
AB series
Inch series
AR-235/275 SIMULATION - 19
FC (8.5” x 13”)
LG (8.5” x 14”)
B4
FC (8.5” x 13”)
LG (8.5” x 14”)
B4
FC (8.5” x 13”)
LG (8.5” x 14”)
B4
LG (8.5” x 14”)
LG (8.5” x 14”)
B4
LG (8.5” x 14”)
LG (8.5” x 14”)
B4
LG (8.5” x 14”)
LG (8.5” x 14”)
B4
LG (8.5” x 14”)
LG (8.5” x 14”)
B4
FC (8.5” x 13”)
FC (8.5” x 13”)
B4
FC (8.5” x 13”)
FC (8.5” x 13”)
B4
A4/LT (8.5" x 11") detection enable/disable setup
In the inch series, Letter is detected as A4; in the AB series, A4 is detected as Letter.
Set value
0
1
Setup
Detection invalid
Detection valid
Remarks
Default
Detection size when A4/LT (8.5" x 11") document/paper is used.
Employed unit
Document
Document
table/SPF
Destination
AB series
Inch series
Paper
Machine paper
feed cassette
Manual paper
feed tray
A4
LT (8.5” x 11”)
A4
LT (8.5” x 11”)
Set value
0
1
(Invalid)
(Valid)
A4
LT (8.5” x 11”)
A4
LT (8.5” x 11”)
LT (8.5” x 11”)
A4
LT (8.5” x 11”)
A4
–
Set with key operations.
–
Regardless of the simulation
setup.
Document size
All destinations
All destinations
26-3
Purpose
Function
(Purpose)
Section
Item
26-6
Setting
Used to set the specifications of the auditor. Setting
must be made depending on the use condition of the
auditor.
Auditor
Specifications
Purpose
Function (Purpose)
Item
Setting
Used to set the specifications depending on
the destination.
Specifications
Destination
Operation/procedure (Pattern 1)
Select the destination.
Operation/procedure (Pattern 1)
Sim26-6 DESTINATION
DESTINATION
0
(0:JAPAN 1:SEC
2:SECL 3:SEEG 4:SUK
1/3 [ 0- 13]
0
Set the auditor.
Sim26-3 AUDITOR SET
AUDITOR
0
(0:P10 1:VENDOR
2:OTHER)
[ 0- 2]
0
Display
items
0:P10
1:VENDOR
2:OTHER
Content
Built-in auditor mode
Coin vendor mode
Others
Setting
range
0-2
Default
0
26-5
Purpose
Function
(Purpose)
Item
Setting
Used to set the count mode of the total counter and the
maintenance counter.
Specifications
Counter
Operation/procedure (Pattern 2)
Used to set the count up number (1 or 2) when an A3/WLT paper
passes through.
For the drum counter and the developer counter, double count is
employed unconditionally.
(Target counter selection)
1:TOTAL COUNTER
2:MAINTE COUNTER
Total
Maintenance
Used to set the count up number of the selected counter.
1:SINGLE COUNT
2:DOUBLE COUNT
Single count
Double count
Setting range
Default
(Initial screen)
1-2
2
(Input screen)
Sim26-5 COUNT MODE
1:TOTAL COUNTER 1
2:MAINTE COUNTER 1
2
Sim26-5 COUNT MODE
2:MAINTE COUNTER 1
(1:SINGLE COUNT
2:DOUBLE COUNT)
[ 1- 2]
1
Display
items
0:JAPAN
1:SEC
2:SECL
3:SEEG
4:SUK
5:SCA
6:SEF
7:INEG
8:ABEG
9:INEF
10:ABEF
11:CHINESE
12:TAIPEI
13:SEEG2
Content
Japan
SEC
SECL
SEEG
SUK
SCA
SEF
EX inch series
EX AB series
EX inch series (FC)
EX AB series (FC)
China
Taiwan
SEEG2
Setting
range
0-13
Default
0
26-10
Function
(Purpose)
Used to enter the Software Key for the Network
Scanner. (Setup is allowed only when the PCL board is
installed.
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the NETWORK soft key and press the [OK]
key, and the collating result is displayed with OK or NG.
When "0" is entered to the soft key, it is treated as a trial setup.
(Initial screen)
(In case of OK)
(In case of NG)
Sim26-10 SCANNERKEY
SCANNER KEY ON
-------------------
AR-235/275 SIMULATION - 20
Sim26-10 SCANNERKEY
SCANNER KEY OK
-------------------
Sim26-10 SCANNERKEY
SCANNER KEY NG
----------
After canceling the simulation, if OK, the scanner function is enable; if
NG, the scanner function is disabled.
26-20
Used to set the job separator paper exit mode.
Function
(Purpose)
Operation/procedure (Pattern 1)
This setting must be reset after the simulation cancel.
Note: Executable only when the SCANNER is installed.
Input the set value with the 10-key and press the [OK] key.
26-12
Function
(Purpose)
Sim26-20 JOBSEP OUT
JOBSEP OUT MODE 0
(0:OFF 1:ON)
Used to input the Software Key for E-MAIL RIC.
Operation/procedure
[ 0- 1]
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the E-MAIL RIC soft key and press the
[OK] key, and the collating result is displayed with OK or NG.
(Initial screen)
(In case of OK)
(In case of NG)
Sim26-12 E-MAIL KEY
E-MAIL KEY OK
-------------------
Sim26-12 E-MAIL KEY
E-MAIL KEY ON
-------------------
Sim26-12 E-MAIL KEY
E-MAIL KEY
NG
-------------------
Display
items
0:OFF
1:ON
0
Content
Paper is discharged to No. 1
paper exit port.
Used to discharge paper to the
job separator tray (No. 2 paper
exit port).
Setting
range
0-1
Default
0
Note: Executable only when the finisher is not installed.
After canceling the simulation, if OK, the E-MAIL RIC function is
enable; if NG, the E-MAIL RIC function is disabled.
This setting must be reset after the simulation cancel.
Purpose
Function
(Purpose)
Item
Note: Executable only when the PCL/NIC is installed.
26-14
Function
(Purpose)
26-22
Used to input the Software Key for the PS extention kit.
Setting
Used to set the specification (language display) for the
destination.
Specifications
Operation/procedure (Pattern 1)
Select the language to be used according to the table below.
Operation/procedure
This setup varies in connection with SIM 26-6 (Destination setup).
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the PS expansion kit soft key and press the
[OK] key, and the collating result is displayed with OK or NG.
(Initial screen)
(In case of OK)
(In case of NG)
Sim26-14 PS KIT KEY
PS KIT KEY OK
-------------------
Sim26-14 PS KIT KEY
PS KIT KEY ON
-------------------
Sim26-14 PS KIT KEY
PS KIT KEY
NG
-------------------
After canceling the simulation, if OK, the PS expansion kit function is
enable; if NG, the PS expansion kit function is disabled.
This setting must be reset after the simulation cancel.
Note: Executable only when the PCL/PS3 is installed.
26-18
Purpose
Function
(Purpose)
Item
Setting
Used to set enable/disable of toner save operation.
Specifications
Sim26-22 LANGUAGE
LANGUAGE
0
(0:JAPANESE
1:ENG.US 2:ENG.UK
1/3 [ 0- 19]
0
Display items
0:JAPANESE
1:ENG.US
2:ENG.UK
3:FRENCH
4:GERMAN
5:ITALY
6:DUTCH
7:SWEDISH
8:SPANISH
9:PORTUGUESE
10:TURKISH
11:GREEK
12:POLISH
13:HUNGARIAN
14:CZECHOSLOVAK
15:RUSSIAN
16:FINNISH
17:NORWEGIAN
18:DANISH
19:CHINESE
Setting
range
0-19
Default
0
Operation mode (Common)
Operation/procedure (Pattern 1)
26-30
Input the set value with the 10-key and press the [OK] key.
Purpose
Function
(Purpose)
Item
Sim26-18 TONER SAVE
TONER SAVE MODE 0
(0:OFF 1:ON)
Setting
Used to set the operation mode for CE mark.
Specifications
Operation mode (Common)
Operation/procedure (Pattern 1)
[ 0- 1]
Display
items
0:OFF
1:ON
0
Input the set value with the 10-key and press the [OK] key.
Content
Disable
Enable
Setting
range
0-1
This setup varies in connection with SIM 26-6 (Destination setup).
Default
0
Sim26-30 CE MARK
CE MARK CONTROL 0
(0:OFF 1:ON)
[ 0- 1]
Note
Setup is allowed only for Japan and UK.
AR-235/275 SIMULATION - 21
0
Display items
Setting range
0-1
0:OFF
1:ON
Default
Japan, SEC, SECL,
SCA, SEF, Taiwan
0
26-38
Others
1
26-35
Setting
Purpose
Used to set whether to stop when the drum life is
Function
(Purpose) reached.
Operation
Item
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Setup
Purpose
Used to set the mode of trouble memory.
Function
(Purpose)
Specifications
Item
Operation/procedure (Pattern 1)
Sim26-38 DRUM STOP
DRUM LIFE OVER
0
(0:STOP
1:NON STOP)
[ 0- 1]
0
Used to set whether the trouble history of SIM 22-4 is displayed as
one-time trouble or as a number of times of troubles continuously
occurred when two or more troubles of the same kind occurred.
Enter the set value with 10-key, and press [OK] key.
Display item
0:ONCE
Purpose
Function
(Purpose)
0
Set range
0-1
Default
0
Sim26-46 OUT DIR
OUT DIRECTION
0
(0:OFF 1:ON)
Operation/procedure (Pattern 1)
[ 0- 1]
Display items
0:OFF
1:ON
0
Content
Setting No
Setting Yes
Sim26-36 MAINTESTOP
MAINTENANCE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1]
0
Setting range
0-1
Purpose
Function
(Purpose)
Item
Default
1
Setting
Used to set whether to use the black/white reverse
function.
Operation
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Sim26-50 B/W REV.
B/W REVERSE
0
(0:ON 1:OFF)
26-37
Setting
Used to set whether to stop when the developer life is
reached.
Operation
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Sim26-37 DEVE. STOP
DEVE. LIFE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1]
0
Display items
0:STOP
1:NON STOP
Content
Stop
Non stop
Default
0
26-50
Note: Executable only with SRU (AR models).
Purpose
Function
(Purpose)
Item
Setting range
0-1
Note: Executable only when the finisher is installed.
Input the set value with the 10-key and press the [OK] key.
Content
Stop
Non stop
Item
Setting
Used to set whether to meet with the output direction of
images regardless of the mode when installing the
finisher.
Operation
Input the set value with the 10-key and press the [OK] key.
Setting
Used to set whether to stop when the maintenance life
is reached.
Operation
Display items
0:STOP
1:NON STOP
Default
0
Operation/procedure (Pattern 1)
26-36
Purpose
Function
(Purpose)
Item
Setting range
0-1
26-46
Content
When two or more troubles
occur, only one is registered.
All the troubles occurred are
registered.
1:ANY
Content
Stop
Non stop
Note: Executable only with CRU (DM models).
Sim26-35 TROUBLE
TROUBLE MODE
0
(0:ONCE 1:ANY)
[ 0- 1]
Display items
0:STOP
1:NON STOP
[ 0- 1]
Display
items
0:ON
1:OFF
Content
Enable
Disable
Setting
range
0-1
Default
0
0
26-54
Purpose
Function
(Purpose)
Item
Setting
Used to set the PWM duty (brightness) at the center
value of the LCD contrast.
Operation
Operation/procedure (Pattern 1)
Setting range
0-1
Default
0
Input the set value with the 10-key and press the [OK] key, and the
LCD contrast will be immediately changed and displayed.
Sim26-54 LCD DUTY
LCD PWM DUTY
0
Note: Executable only with CRU (DM models).
[ 30- 70]
Setting range
Default
AR-235/275 SIMULATION - 22
0
30-70
50
Operation/procedure (Pattern 1)
26-57
Input the set value with the 10-key and press the [OK] key.
Setting
Purpose
Used to set the model code.
Function
(Purpose)
Operation
Item
Operation/procedure (Pattern 1)
Sim27-1 U7-00 SET.
DISABLE U7-00
0
(0:OFF 1:ON)
[ 0- 1]
0
Input the set value with the 10-key and press the [OK] key.
Display
items
0:OFF
Sim26-57 MACHINE
MACHINE CODE
1
(1:AR-235
2:AR-255S
1/5 [ 1-10]
1
Content
In case of the communication
trouble, U7-00 is not displayed.
In case of the communication
trouble, U7-00 is displayed.
1:ON
Display items
Setting range
1-10
1:AR-235
2:AR-255S
3:AR-255P
4:AR-255F
5:AR-255FP
6:AR-275
7:AR-N275
8:DM-2305
9:DM-2515
Default
1
Purpose
Function
(Purpose)
Item
0
Setting
Used to enter the TAG No. of the copier.
Data
Operation/procedure
Current memory is displayed in PRESENT column.
Enter a value (max. 8 digits) with the 10-key, and press the [OK] key.
The input number is displayed instead of "NEW".
If a model different from CPM setup (22cpm or 27cpm) of BOOT is set,
a system error will occur after canceling the simulation.
26-60
Item
Default
27-5
10:DM-2705
Purpose
Function
(Purpose)
Setting
range
0-1
Setting
Used to set enable/disable of the FAX mode key when
FAX is not installed. (When FAX is installed, the FAX
mode is enabled regardless of this setup.)
Operation
Operation/procedure (Pattern 1)
The set value is stored and "PRESENT" of LCD is revised.
Sim 27-5 TAG# SET.
TAG# SETTING
PRESENT :
NEW
:12345678
30
Input the set value with the 10-key and press the [OK] key.
This setup varies in connection with SIM 26-6 (Destination setup).
Purpose
Function
(Purpose)
Sim26-60 FAX KEY
FAX KEY SETTING 0
(0:ON 1:OFF)
[ 0- 1]
Display
items
0:ON
1:OFF
30-1
0
Content
Effective (The
message with FAX
uninstalled is
displayed.)
Disable (Error Beep)
Setting
range
0-1
Default
JAPAN,
SEC, SECL, Others
SUK, SCA
0
1
Section
Item
Operation test/check
Used to check the operation of sensors and detectors
in the sections other than the paper feed section of the
copier and the related circuit. (The operation of
sensors and detectors can be monitored with the
LCD.)
Others
Operation
Operation/procedure
The operating conditions of sensors and detectors in the different sections than the paper feed section of the machine are displayed. The
active sensors and detectors are highlighted.
Sim30-1 MAIN SENSOR
PPD1H PPD1L PPD2
POD1 DVCH DRST
DSWR1 SFTHP POD2
TOPF DSWR0 LOEMP
27
27-1
Purpose
Function
(Purpose)
Section
Item
Setting
Used to set PC/MODEM communication trouble (U700) detection Yes/No.
Communication (RIC/MODEM)
Specifications
Operation mode
(Common)
PPD1H
PPD1L
PPD2
POD1
DVCH
DRST
DSWR1
SFTHP
POD2
TOPF
DSWR0
LOEMP
AR-235/275 SIMULATION - 23
PS paper detection 1 sensor
PS paper detection 2 sensor
Duplex sensor
1st paper exit paper out sensor
Developing cartridge detection sensor
Drum intial detection sensor
Interlock switch (side door)
Shifter home position sensor
2nd paper exit paper out sensor
2nd paper exit full detection sensor
2nd paper exit cover open/close detection sensor
1st paper exit empty detection sensor
40-2
30-2
Operation test/check
Used to check the operation of sensors and detectors
in the paper feed section and the related circuits. (The
operations of sensors and detectors in the paper feed
section can be monitored with the LCD.)
Paper feed
Section
Operation
Item
Operation/procedure
Purpose
Function
(Purpose)
The operating conditions of sensors and detectors in the paper feed
section of the machine are displayed. The active sensors and detectors are highlighted.
Sim30-2 TRAY SEN1/2
PED1 LUD1 CD1
PED2 LUD2 CD2 PFD2
DSWR2
MPED
Adjustment
Purpose
Used to adjust the manual paper feed tray paper width
Function
(Purpose) detector detection level.
Paper feed
Section
Operation
Item
Operation/procedure
1) Set A3/W Letter and fit the guide, then press the [OK] key.
2) Set A4R/LetterR and fit the guide, then press the [OK] key.
When the intermediate position adjustment is not performed, press
the [OK] key without changing the guide position.
3) Set to A5R/INVOICE R and fit the guide, then press the [OK] key.
When the intermediate position adjustment is not performed, press
the [OK] key without changing the guide position.
4) Narrow the guide at minimum, press the [OK] key.
5) Set the paper detection width (+), and press the [OK] key.
6) Set the paper detection width (–), and press the [OK] key.
PED1
LUD1
CD1
PED2
LUD2
CD2
PFD2
DSWR2
MPED
MPLS1
MPLS2
MPLD1
MPLD2
1st cassette paper empty sensor
1st cassette paper upper limit detection sensor
1st cassette empty sensor
2nd cassette paper empty sensor
2nd cassette paper upper limit detection sensor
2nd cassette empty sensor
2nd cassette paper pass sensor
2nd cassette right door detection sensor
Manual tray paper empty detection
Manual tray length detection 1
Manual tray length detection 2
Manual feed paper length detection 1
Manual feed paper length detection 2
If "FAILED" is displayed in procedure 1), 2), 3), or 4), it is NG of adjustment. Repeat the adjustment.
(Maximum position setting
screen: AB series)
(Maximum position setting screen:
Inch series)
Sim40-2 MB SENSOR
A3 PAPER SET
Sim40-2 MB SENSOR
WLT PAPER SET
PRESS OK KEY
PRESS OK KEY
(Intermediate position L setting (Intermediate position L setting
screen: AB series)
screen: INCH series)
Sim40-2 MB SENSOR
A4R PAPER SET
Sim40-2 MB SENSOR
LTR PAPER SET
PRESS OK KEY
PRESS OK KEY
Width detection size of the manual feed tray (one of them is displayed.)
A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA
(At detection, highlighted)
If the intermediate position adjustment is not performed, press the
[OK] key without changing the guide position.
40
(Intermediate position S setting (Intermediate position S setting
screen: AB series)
screen: INCH series)
40-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the operation of the manual paper feed
tray paper size detector and the related circuit. (The
operation of the manual paper feed tray paper size
detector can be monitored with the LCD.)
Paper feed
Operation
Operation/procedure
The status of sensors and detectors in the manual paper feed section
is displayed. The active sensors and detectors are highlighted.
Sim40-2 MB SENSOR
A5R PAPER SET
Sim40-2 MB SENSOR
INVR PAPER SET
PRESS OK KEY
PRESS OK KEY
If the intermediate position adjustment is not performed, press the
[OK] key without changing the guide position.
(Minimum position setting screen)
Sim40-2 MB SENSOR
MIN POSITION SET
PRESS OK KEY
Sim40-1 MB SENSOR
MPLS1 MPLS2 MPLD1
MPLD2 A3/A4 INV/LTR
B5/B4 LT/WLT A5/A4R
B5R POSTCARD EXTRA
MPLS1
MPLS2
Manual tray length
detection 1
Manual tray length
detection 2
(Paper width detection (+)
setting screen)
MPLD1
MPLD2
Manual feed paper
length detection 1
Manual feed paper
length detection 2
Sim40-2 MB
PAPER +
MID-L ADJ.
MID-S ADJ.
[ 1-
SENSOR
60
ON
ON
99]
60
(Paper width detection (–) setting
screen)
Sim40-2 MB SENSOR
PAPER40
MID-L ADJ. ON
MID-S ADJ. ON
[ 1 -99] 40
The intermediate position adjustment setup YES/NO is displayed.
Width detection size of the manual feed tray (one of them is displayed.)
A4/A3, LT/WLT, B5/B4, INV/LTR, A5/A4R, B5R, POSTCARD, EXTRA
AR-235/275 SIMULATION - 24
Sim40-2 MB SENSOR
PAPER +
60
PAPER 40
COMPLETE
LON SON
(Executing screen)
(Initial screen)
(Adjustment result screen)
Adjustmen state is displayed.
Sim41-2 PD SENSOR
Paper width detection (+) adjustment
value
Paper width detection (–) adjustment
value
Intermediate position L YES : LON
Intermediate position L NO : LOFF
Intermediate position S YES : SON
Intermediate position S NO : SOFF
PRESS OK KEY
EXEC
OCSW
Original cover state
1 to 5
PD sensor detection
Open: Highlighted display
level
Close: Normal display
The value in [ ] shows the threshold value.
For AB series, 1 - 5 is displayed, for inch series, 1 - 4.
During execution, [EXEC] is highlighted.
40-3
Adjustment
Purpose
The AD conversion value of manual feed width
Function
(Purpose) detection is displayed.
Paper feed
Section
Operation
Item
Operation/procedure
The AD conversion value of manual feed width detection is displayed.
41-3
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the light reception level and the
detection level of the original size detection photo
sensor.
Others
Operation
Operation/procedure
Sim40-3 MB SENSOR
AD CONVERT VALUE
The detection output level of each sensor is displayed in real time.
[123]
41
OCSW
41-1
Purpose
Function
(Purpose)
Section
Item
Operation test/check
Used to check the document size detection photo
sensor.
Others
Operation
Operation/procedure
The operation status of the sensors and detectors in the original size
detection section are displayed. The active sensors and detectors are
highlighted.
Sim41-1 PD SENSOR
OCSW PD1 PD2
PD3 PD4 PD5
Original cover state
Open: Highlighted display
Close: Normal display
1 to 5
PD sensor detection
level
The value in [ ] shows the threshold value of 20 degree detection
adjustment.
For AB series, 1 - 5 is displayed, for inch series, PD1 - 4.
41-4
Purpose
Function
(Purpose)
Section
Item
Adjustment
Used to adjust the detection level of OC 20 degrees.
Others
Operation
Operation/procedure
Set the OC cover at 20 degrees detection and press the [OK] key.
(Initial screen)
OCSW
Original cover state
Open: Highlighted
display
Close: Normal display
PD1 to 5
Original sensor status
Without original:
Normal display
With original:
Highlighted display
For AB series, PD1 - 5 is displayed, for inch series, PD1 - 4.
Purpose
Function
(Purpose)
Section
Item
Sim41-4 20˚ SENSOR
PRESS OK KEY EXEC
The detection output level of each sensor is displayed in real time.
OCSW
41-2
Adjustment
Used to adjust the detection level of the document size
photo sensor.
Others
Operation
Operation/procedure
(Executing screen)
Original cover state
Open: Highlighted
display
Close: Normal display
1 to 5
PD sensor
detection level
The value in [ ] shows the threshold value of 20 degree detection
adjustment.
For AB series, 1 - 5 is displayed, for inch series, 1 - 4.
During execution, [EXEC] is highlighted.
Place an A3 (or WLT) document on the document table, and press
[OK] key with the OC cover open.
The adjustment is performed and the result is displayed.
AR-235/275 SIMULATION - 25
43
Display items
Content
ENVIRONMENT ADJ.
Environmental correction
Valid/Invalid
(0: Environmental
correction invalid
1: Environmental
correction valid)
43-1
Setting
Purpose
Used to set the fusing temperature in each operation
Function
(Purpose) mode.
Fixing (Fusing)
Section
Operation
Item
Operation/procedure (Pattern 2)
After the mode selection, enter the adjustment value and press the
[OK] key.
(Initial screen)
(Input screen)
Sim43-1 FUSER TEMP.
1:600dpi
185
2:1200dpi
160
3:POST CARD
185
2
Display items
1:600dpi
2:1200dpi
3:POST CARD
Sim43-1 FUSER TEMP.
2:1200dpi
160
Setting range
155-190
140-190
155-190
1
44-34
Adjustment
Purpose
Used to adjust the transfer current value.
Function
(Purpose)
Operation/procedure
When changing +V2, check with +V1 unchanged. If there is any trouble
in the half tone image of graphics, keep the relationship between +V1
and +V2 at the default and change it.
Default
185
160
185
When the image quality is deteriorated because the user selects the
OHP mode and use other than the recommended OHP, decrease the
transfer current to adjust deterioration of black background picture
quality. If some of characters are not printed, increase the transfer current.
43-10
Purpose
Function
(Purpose)
Section
Item
Default
To support an individual necessity in paper and the environment, it is
variable in the range of 5 to 30uA in the increment of 1uA in each
mode.
[140-190] 160
Content
600dpi
1200dpi
Postcard
Setting
range
0-1
Setting
Used to set the paper feed cycle for postcard.
Paper feed
Operation
Operation/procedure (Pattern 1)
(Initial screen)
Sim44-34
1:+V1
2:+V2 F
3:+V2 R
1/4
(Input/Executing screen)
TC ADJ.
(600) 20
(600) 20
(600) 18
Sim44-34 TC ADJ.
4:+V2 S-F(600) 22
[ 5- 30]
22
Input the set value with the 10-key and press the [OK] key.
Sim43-10 POST CARD
PICK UP CYCLE
50
[ 1- 99]
Setting range
Default
Display items
1-99
50
44
44-1
Purpose
Function
(Purpose)
Section
Item
Setting
Used to make various setups in each mode of process
control.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Operation
Operation/procedure (Pattern 1)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Sim44-1 PROCON MODE
ENVIRONMENT ADJ. 1
[ 0- 1]
1
600dpi +V1
600dpi +V2 front
surface
3:+V2 R (600)
600dpi +V2 back
surface
4:+V2 S-F(600)
600dpi +V2 small
size front
5:+V2 S-R(600)
600dpi +V2 small
size back
6:+V2 OHP(600)
600dpi +V2OHP
7:+V1 (1200)
1200dpi +V1
8:+V2 F (1200)
1200dpi +V2 front
surface
9:+V2 R (1200)
1200dpi +V2 back
surface
10:+V2 S-F(1200) 1200dpi +V2 small
size front
11:+V2 S-R(1200) 1200dpi +V2 small
size back
12:+V2 OHP(1200) 1200dpi +V2OHP
1:+V1 (600)
2:+V2 F (600)
50
Content
Setting
range
5-30
5-30
Default
Japan,
Others
USA
18
20
18
20
5-30
16
16
5-30
24
24
5-30
18
18
5-30
5-30
5-30
20
8
12
20
8
14
5-30
8
8
5-30
14
14
5-30
12
12
5-30
10
10
44-35
Purpose
Function
(Purpose)
Setting
Correction temperature setup when correcting the
ambient temperature.
Operation/procedure
Correction is performed when the temperature sensor installed to the
MCU indicates 15°C or below.
The content of correction is to raise the DVB-Bias and Grid by –50V.
The simulation allows to vary the correction threshold value in the
range of 0 to 20°C.
AR-235/275 SIMULATION - 26
If, however, the set temperature is increased, correction at a high voltage is performed in normal temperatures.
Sim44-35 ENV.ADJ.
DVB/GRID ENV TMP 15
[ 0- 20]
Setting range
Default
0-20
15°C
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-7 SUPER PHOTO
1:
1.0(SHIFT) 50
2:
1.0(GAMMA) 50
3:
2.0(SHIFT) 50
1/4
50
15
44-40
Display items
Purpose
Function
(Purpose)
Setting
Used to set the rotating time before toner supply.
Operation/procedure (Pattern 1)
Enter the set value with the 10-key, and the set value will be registered.
Sim44-40 TONER
ROTATE TIME
50
[ 1- 99]
8
Setting range
Default
1-99
8
1:1.0(SHIFT)
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
10:5.0(GAMMA)
Content
Super photo level 1.0 (shift q’ty)
Super photo level 1.0 (slant)
Super photo level 2.0 (shift q’ty)
Super photo level 2.0 (slant)
Super photo level 3.0 (shift q’ty)
Super photo level 3.0 (slant)
Super photo level 4.0 (shift q’ty)
Super photo level 4.0 (slant)
Super photo level 5.0 (shift q’ty)
Super photo level 5.0 (slant)
Setting
Default
range
1-99
32
1-99
50
1-99
41
1-99
50
1-99
50
1-99
50
1-99
56
1-99
61
1-99
62
1-99
66
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
46
46-9
46-2
Purpose
Function
(Purpose)
Item
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the copy exposure level.
Picture quality
Density
Operation/procedure (Pattern 5)
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
(Auto adjustment)
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:AE(TS)
7:TEXT(TS)
8:TEXT/PHOTO(TS)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-9 TEXT
1:
1.0(SHIFT)
2:
1.0(GAMMA)
3:
2.0(SHIFT)
1/7
Sim46-2 EXP. LEVEL
1:AE
50
2:TEXT
50
3:TEXT/PHOTO
50
1/3
50
Display items
Adjustment
Used to adjust individually the copy exposure level.
(Character)
Picture quality
Density
50
50
50
50
Display items
Setting
range
1-99
Content
AE
Character
Character/Photo
Photo
Super photo
AE (TS)
Character (TS)
Character/Photo (TS)
Default
1:1.0(SHIFT)
50
Level 3.0
Level 3.0
Level 3.0
Level 3.0
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
Level 3.0
Level 3.0
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
46-7
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust individually the copy exposure level.
(Super photo)
Picture quality
Density
10:5.0(GAMMA)
11:TS 1.0(SHIFT)
12:TS 1.0(GAMMA)
Operation/procedure (Pattern 5)
13:TS 2.0(SHIFT)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
14:TS 2.0(GAMMA)
AR-235/275 SIMULATION - 27
Content
Character level 1.0 (shift
q’ty)
Character level 1.0 (slant)
Character level 2.0 (shift
q’ty)
Character level 2.0 (slant)
Character level 3.0 (shift
q’ty)
Character level 3.0 (slant)
Character level 4.0 (shift
q’ty)
Character level 4.0 (slant)
Character level 5.0 (shift
q’ty)
Character level 5.0 (slant)
Character (TS) level 1.0
(shift q’ty)
Character (TS) level 1.0
(slant)
Character (TS) level 2.0
(shift q’ty)
Character (TS) level 2.0
(slant)
Setting
range
1-99
Default
22
1-99
1-99
44
36
1-99
1-99
47
50
1-99
1-99
50
61
1-99
1-99
55
72
1-99
1-99
60
22
1-99
44
1-99
36
1-99
47
Display items
Content
Setting
range
1-99
Default
Character (TS) level 3.0
50
(shift q’ty)
16:TS 3.0(GAMMA) Character (TS) level 3.0
1-99
50
(slant)
17:TS 4.0(SHIFT) Character (TS) level 4.0
1-99
61
(shift q’ty)
18:TS 4.0(GAMMA) Character (TS) level 4.0
1-99
55
(slant)
19:TS 5.0(SHIFT) Character (TS) level 5.0
1-99
72
(shift q’ty)
20:TS 5.0(GAMMA) Character (TS) level 5.0
1-99
60
(slant)
Setup of various copy conditions: Similar to the normal copy mode.
15:TS 3.0(SHIFT)
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
46-10
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust individually the copy exposure level.
(Character/Photo)
Picture quality
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-10 TEXT/PHOTO
1:
1.0(SHIFT) 50
2:
1.0(GAMMA) 50
3:
2.0(SHIFT) 50
1/7
50
Display items
Content
Display items
1:1.0(SHIFT)
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
10:5.0(GAMMA)
11:TS 1.0(SHIFT)
12:TS 1.0(GAMMA)
13:TS 2.0(SHIFT)
14:TS 2.0(GAMMA)
15:TS 3.0(SHIFT)
Content
Character/Photo level 1.0
(shift q’ty)
Character/Photo level 1.0
(slant)
Character/Photo level 2.0
(shift q’ty)
Character/Photo level 2.0
(slant)
Character/Photo level 3.0
(shift q’ty)
Character/Photo level 3.0
(slant)
Character/Photo level 4.0
(shift q’ty)
Character/Photo level 4.0
(slant)
Character/Photo level 5.0
(shift q’ty)
Character/Photo level 5.0
(slant)
Character/Photo (TS)
level 1.0 (shift q’ty)
Character/Photo (TS)
level 1.0 (slant)
Character/Photo (TS)
level 2.0 (shift q’ty)
Character/Photo (TS)
level 2.0 (slant)
Character/Photo (TS)
level 3.0 (shift q’ty)
Default
30
1-99
37
1-99
40
1-99
43
1-99
50
1-99
50
1-99
57
1-99
61
1-99
64
1-99
66
1-99
30
1-99
37
1-99
40
1-99
43
1-99
50
Default
Character/Photo (TS)
50
level 3.0 (slant)
17:TS 4.0(SHIFT) Character/Photo (TS)
1-99
57
level 4.0 (shift q’ty)
18:TS 4.0(GAMMA) Character/Photo (TS)
1-99
61
level 4.0 (slant)
19:TS 5.0(SHIFT) Character/Photo (TS)
1-99
64
level 5.0 (shift q’ty)
20:TS 5.0(GAMMA) Character/Photo (TS)
1-99
66
level 5.0 (slant)
Setup of various copy conditions: Similar to the normal copy mode.
16:TS 3.0(GAMMA)
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
46-11
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust individually the copy exposure level.
(Photo)
Picture quality
Density
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-11 PHOTO
1:
1.0(SHIFT)
2:
1.0(GAMMA)
3:
2.0(SHIFT)
1/4
50
50
50
50
Display items
Setting
range
1-99
Setting
range
1-99
Content
1:1.0(SHIFT)
2:1.0(GAMMA)
3:2.0(SHIFT)
4:2.0(GAMMA)
5:3.0(SHIFT)
6:3.0(GAMMA)
7:4.0(SHIFT)
8:4.0(GAMMA)
9:5.0(SHIFT)
10:5.0(GAMMA)
Photo level 1.0 (shift q’ty)
Photo level 1.0 (slant)
Photo level 2.0 (shift q’ty)
Photo level 2.0 (slant)
Photo level 3.0 (shift q’ty)
Photo level 3.0 (slant)
Photo level 4.0 (shift q’ty)
Photo level 4.0 (slant)
Photo level 5.0 (shift q’ty)
Photo level 5.0 (slant)
Setting
range
1-99
Default
32
50
41
50
50
50
56
61
62
66
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
46-12
Purpose
Function
(Purpose)
Adjustment
FAX exposure level adjustment (batch)
Operation/procedure
Shading is performed to turn on the copy LED.
The current exposure value of "Normal character, Auto exposure"
mode is displayed.
Enter an adjustment value of 2 digits with the 10-key and press the
START key, and the entered value will be set to all the modes and the
self print will be made in the normal size.
Exposure adjustment value table
AR-235/275 SIMULATION - 28
Mode
AE
Photo
Exposure adjustment
ON
–
STD
(Standard
character)
Auto
Manual
Auto
Manual
Fine
Auto
(Small
Manual
character)
Auto
Manual
S-fine
Auto
(Fine)
Manual
Auto
Manual
U-fine
Auto
(Super fine)
Manual
Auto
Manual
When initializing each data: 50
Display items
OFF
ON
OFF
ON
Individual adjustment
enable
(46-13 to 16)
Character
Level 3.0
Character/Photo
Level 3.0
Photo
Level 3.0
Super photo
Level 3.0
Default
50
AE(TS)
Character (TS)
Level 3.0
Character/Photo (TS) Level 3.0
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
OFF
46-19
Purpose
Function
(Purpose)
Item
Adjustment
FAX exposure level adjustment (individual)
The FAX exposure level can be adjusted separately for each mode by
specifying a sub code. Since selection of Auto/Manual and Photo ON/
OFF is allowed separately for each mode, adjustments of 14 patterns
in total can be made.
(Refer to 46-12, "Exposure adjustment table".)
Adjustment
Used to change the image quality in the exposure
mode.
Picture quality
Operation/procedure (Pattern 2)
Select the mode with the 10-key and press the [OK] key.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
Auto exposure mode
• When SIM 26-6 (Destination setup) is changed from EX to Japan,
the setup value becomes 1 (Default: Japan). If, on the contrary, it is
changed from Japan to EX, the set value becomes 2 (Default: EX)
• If the auto exposure mode setup value is changed, the setup value
of SIM 46-30 (AE limit setup) is reset to the default value.
(Initial screen)
(Input screen)
Mode
STD (normal character)
Fine (small character)
S-fine (super fine)
U-fine (super fine)
Shading is performed to turn on the copy LED.
The current exposure value of the selected mode is displayed.
Enter the 2-digit adjustment value with the 10-key pad and push
START key. The entered value is set for the specified mode, and the
self print is made with the same magnification ratio for the mode.
Note: Executable only when the FAX is installed.
46-18
Adjustment
Used to adjust the copy contrast. (Inclination)
Picture quality
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim46-18 GAMMA SET.
1:AE
50
2:TEXT
50
3:TEXT/PHOTO
50
1/3
50
AE
ON
Operation/procedure
Purpose
Function
(Purpose)
Item
1:AE
2:TEXT
3:TEXT/PHOTO
4:PHOTO
5:SUPER PHOTO
6:AE(TS)
7:TEXT(TS)
8:TEXT/PHOTO(TS)
Setup of various copy conditions: Similar to the normal copy mode.
46-13 to 16
Sub code
13
14
15
16
Setting
range
1-99
Content
OFF
Note: Executable only when the FAX is installed.
Purpose
Function
(Purpose)
(Auto adjustment)
Sim46-19 AE MODE
1:AE MODE
2:AE STOP(COPY)
3:AE STOP(FAX)
1/2
1
0
0
1
Display items
1:AE MODE
(1:EXPOSURE
2:TONER)
2:AE STOP(COPY)
(0:FIXED
1:REAL TIME)
3:AE STOP(FAX)
(0:FIXED
1:REAL TIME)
4:AE STOP(SCAN)
(0:FIXED
1:REAL TIME)
5:1200dpi PHOTO
(1:SOFT
2:HARD)
Sim46-19 AE MODE
1:AE MODE
1
(1:EXPOSURE
2:TONER)
[ 1- 2]
1
Content
Auto exposure mode
(1: Priority on Image quality,
2: Priority on toner consumption)
Auto exposure STOP mode (COPY)
(0: Fixed, 1: Real-time)
Default
2
0
Auto exposure STOP mode (FAX)
(0: Fixed, 1: Real-time)
0
Auto exposure STOP mode
(SCANNER)
(0: Fixed, 1: Real-time)
1200dpi photo mode
(Countermeasures for claims on
dither)
(1: Soft mode, 2: Hard mode)
0
1
46-20
Purpose
Function
(Purpose)
Item
Adjustment
Used to correct SPF exprosure.
Picture quality
Operation/procedure (Pattern 2)
Select the mode with the 10-key and press the [OK] key.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
AR-235/275 SIMULATION - 29
(Initial screen)
Setup of various copy conditions: Similar to the normal copy mode.
(Input screen)
Sim46-20 SPF EXP.
1:SPF EXPOSURE 50
2:RSPF EXPOSURE 50
1
Display items
1:SPF EXPOSURE
2:RSPF EXPOSURE
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
Sim46-20 SPF EXP.
1:SPF EXPOSURE 50
[ 1- 99]
Content
SPF
RSPF
48-2
50
Setting range
1-99
Purpose
Function
(Purpose)
Section
Item
Default
50
Adjustment
Used to adjust the scanner mode magnification ratio
(main/sub scanning direction).
Image processing
Picture quality
46-30
Operation/procedure (Pattern 5)
Setting
Purpose
Used to set the AE limit.
Function
(Purpose)
Operation/procedure (Pattern 2)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
Select the mode with the 10-key and press the [OK] key.
Input the offset for the copy adjustment.
(Initial screen)
(Input screen)
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
If SIM 26-6 (Destination setup) and SIM46-19 (Auto exposure mode)
are changed, this setup is also changed to the default value accordingly.
(Initial screen)
(Input screen)
Sim46-30 AE LIMITTE
1:AE
0
2:AE(TS)
0
1
Display items
1:AE
2:AE(TS)
Setting range
0-31
1:F-R
2:SCAN
0
Default
0
(Executing screen)
MAG
50
50
50
50
Display items
Sim46-30 AE LIMITTE
1:AE
0
[ 0- 31]
Sim48-2 SCANNER
1:F-R
2:SCAN
3:SPF(SIDE1)
1/2
3:SPF(SIDE1)
4:SPF(SIDE2)
Content
Main scanning magnification
ratio adjustment
Sub scanning magnification
ratio adjustment
SPF surface sub scan
magnification ratio
SPF back surface sub scan
magnification ratio
Setting
range
1-99
Default
50
Setup of various copy conditions: Similar to the normal copy mode.
48
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
48-1
Purpose
Function
(Purpose)
Section
Item
Adjustment
Used to adjust the copy mode magnification ratio (main
scanning direction, sub scanning direction).
Image processing
Picture quality
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim48-1 COPY MAG.
1:F-R(AUTO)
50
2:F-R
50
3:SCAN
50
1/2
50
1:F-R(AUTO)
Main scanning magnification
ratio adjustment (auto)
Main scanning magnification
ratio adjustment
Sub scanning magnification
ratio adjustment
SPF surface sub scan
magnification ratio
SPF back surface sub scan
magnification ratio
DUPLEX sub scanning
magnification ratio adjustment
4:SPF(SIDE1)
5:SPF(SIDE2)
6:DUPLEX
Adjustment
Used to adjust the lead edge/sub scan magnification
ratio automatically.
Operation
Open the OC cover, and put the lead edge/sub scan automatic adjustment chart on the OC. (Keep the OC cover open.)
Place the chart correctly on the OC reference position. (If not, a correct
adjustment cannot be made.)
If the adjustment is normally completed, the adjusted value is displayed and written into the EEPROM. In case of an abnormality, "ERR"
is displayed and the value is not written into the EEPROM.
Sim48-3 READ AUTO
Content
3:SCAN
Purpose
Function
(Purpose)
Item
If no adjustment is made because of an abnormality, "---" is displayed.
(Initial screen)
(Execution screen)
Display items
2:F-R
48-3
Setting
range
–
Default
–
50
60
50
EXEC
PRESS OK KEY EXEC
(Normal end screen)
1-99
Sim48-3 READ AUTO
Sim48-3 READ
RRC-A
OC Center
MirSpeed
PRESS OK KEY
AR-235/275 SIMULATION - 30
AUTO
[ 32]
[ 53]
[ 58]
EXEC
(Abnormal end screen)
Sim48-3 READ
RRC-A
OC Center
MirSpeed
PRESS OK KEY
AUTO
[ ERR]
[ ERR]
[ ---]
EXEC
48-8
Display items
Adjustment
Purpose
FAX magnification ratio adjustment (read)
Function
(Purpose)
Related soft SW76-1 to 8, SW77-1 to 8
SW
Operation/procedure
OC read main scanning
magnification ratio
OC read sub scanning
magnification ratio
SPF read main scanning
magnification ratio
SPF read sub scanning
magnification ratio
Adjustment
range
Adjustment
unit
1 – 128 –
255%
0.1%
increment
Note: Executable only when the FAX is installed.
48-9
Purpose
Function
(Purpose)
Related soft SW
Adjustment
FAX magnification ratio adjustment (print)
Setting
range
1-99
Default
Original scan start position
43
adjustment
2:RRC-B
Lead edge cancel
1-99
18
adjustment (Main
cassette)
3:RRC-MANUAL
Lead edge cancel
1-99
18
adjustment (Manual feed
cassette)
4:RRC-OPTION
Lead edge cancel
1-99
18
adjustment (Option
cassette)
5:RRC-DUPLEX
Lead edge cancel
1-99
18
adjustment (back of the
machine)
6:DEN-B
Rear edge void adjustment
1-99
30
7:DEN-B-DUP
Rear edge void adjustment
1-99
50
(Duplex)
8:SIDE VOID
Left edge void adjustment
1-99
18
(First print surface)
9:SIDE VOID-DUP Left edge void adjustment
1-99
18
(Duplex)
10:LOSS(OC)
Image loss quantity
1-5
3
adjustment
Setup of various copy conditions: Similar to the normal copy mode.
1:RRC-A
Adjust and set FAX document read magnification ratio, read and print
the document.
Adjustment magnification ratio
Content
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
SW78-1 to 8, SW79-1 to 8
Operation/procedure
After the adjustment/setting of FAX print magnification ratio, read and
print the document.
Adjustment magnification ratio
Main scanning magnification ratio
Sub scanning magnification ratio
Adjustment
range
1 – 128 –
255%
Adjustment
unit
0.1%
increment
50-5
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the print image position (top margin) on
the print paper in the print mode.
Picture quality
Print area
Operation/procedure (Pattern 5)
Note: Executable only when the FAX is installed.
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
48-10
Purpose
Function
(Purpose)
Related soft SW
Adjustment
FAX auto reduction magnification ratio (print).
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-5 PRINT EDGE
1:TRAY1
50
2:OPTION
50
3:MANUAL
50
1/2
50
SW25-1 to 4
Operation/procedure
Set the FAX auto reduction magnification ratio (0 to 15%).
Note: Executable only when the FAX is installed.
Display
items
1:TRAY1
2:OPTION
3:MANUAL
4:DUPLEX
50
50-1
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the copy lead edge position.
Picture quality
1st cassette
Option cassette
Manual feed
Back print
Setting range
Default
0-99
1-99
53
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
Image position
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-1 LEAD EDGE
1:RRC-A
43
2:RRC-B
18
3:RRC-MANUAL
18
1/4 [ 1- 99] 43
Content
50-6
Purpose
Function
(Purpose)
Item
Adjustment
Used to adjust the print image position (top margin) on
print paper in the copy mode. (SPF/RSPF)
Picture quality
Image position
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
AR-235/275 SIMULATION - 31
(Initial screen)
(Input screen)
(Executing screen)
Sim50-6 SPF EDGE
1:SIDE1
50
2:SIDE2
50
3:DEN-B
50
1/4
50
Adjustment
Purpose
FAX lead edge adjustment (print)
Function
(Purpose)
Related soft SW SW74-1 to 4, SW75-5 to 8
Operation/procedure
Display items
Setting
range
1-99
Content
Default
Surface original scan start
50
position adjustment value
2:SIDE2
Back original scan start
1-99
50
position set value
3:END EDGE
Rear edge void
1-99
50
adjustment value (SPF)
4:LOSS(SIDE1)
Surface image loss
1-5
3
quantity set value
5:LOSS(SIDE2)
Back image loss quantity
1-5
3
set value
6:REARLOS(SIDE1) Surface rear edge image
1-5
3
loss quantity set value
7:REARLOS(SIDE2) Back rear edge image
1-5
3
loss quantity set value
Setup of various copy conditions: Similar to the normal copy mode.
1:SIDE1
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
50-8
The adjustments on the machine side must have been normally
completed.
Purpose
Function
(Purpose)
Related soft SW
50-9
Adjustment
FAX lead edge adjustment (read)
SW44-5 to 8, SW45-5 to 8
Operation/procedure
Adjust and set FAX document read lead edge position, read and print
the document.
OC read
SPF read
E
A
B
After the adjustment/setting of FAX print lead edge position, read and
print the document.
Adjustment position
A
B
Lead edge position
Left edge position
Adjustment range
43 – 50 – 57
43 – 50 – 57
Adjustment
unit
16 lines
16 dots
Note: Executable only when the FAX is installed.
50-10
Adjustment
Used to adjust the print image center position.
(Adjustment can be made for each paper feed
section.)
Image processing (ICU)
Picture quality
Image position
Purpose
Function
(Purpose)
Section
Item
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-10 PRT.CENTER
1:BYPASS
50
2:TRAY1
50
3:TRAY2
50
1/2
50
Display items
1:BYPASS
2:TRAY1
3:TRAY2
4:TRAY3
5:TRAY4
6:DUPLEX
Content
Manual feed
1st cassette
2nd cassette
3rd cassette
4th cassette
Back print
Setting range
1-99
Default
50
Setup of various copy conditions: Similar to the normal copy mode.
F
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
Read area
50-12
Read area
D
H
C
A
B
C
D
E
F
G
H
G
Adjustment position
Adjustment range
OC read lead edge position
OC read left edge position
OC read rear edge position
OC read right edge position
SPF read lead edge position
SPF read left edge position
SPF read rear edge position
SPF read right edge position
43 – 50 – 57 lines
43 – 50 – 57 lines
43 – 50 – 57 lines
43 – 50 – 57 lines
43 – 50 – 57 lines
43 – 50 – 57 lines
43 – 50 – 57 lines
43 – 50 – 57 lines
Adjustment
unit
8 lines
8 dots
8 lines
8 dots
8 lines
8 dots
8 lines
8 dots
Purpose
Function
(Purpose)
Section
Item
Adjustment
Used to adjust the print image center position.
(Adjustment can be made for each document mode.)
Image processing
Picture quality
Image position
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim50-12 ORG.CENTER
1:OC
50
2:SPF(SIDE1)
50
3:SPF(SIDE2)
50
50
Note: Executable only when the FAX is installed.
AR-235/275 SIMULATION - 32
Display items
Content
Setting range
Default
1:OC
OC
1-99
50
2:SPF(SIDE1) SPF front surface
3:SPF(SIDE2) SPF back surface
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
51-1
Item
Setting
Used to set to disable the operation of the separation
pawl of the photoconductor drum.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Operation
Item
Operation/procedure (Pattern 1)
Purpose
Function
(Purpose)
Section
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
51
Purpose
Function
(Purpose)
Section
51-8
Adjustment
Used to adjust the OPC drum separation pawl ON
time.
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Operation
Sim51-8 D/F SETTING
DETACH FINGER
0
(0:ON
1:OFF)
[ 0- 1]
1
Display items
0:ON
1:OFF
Content
Setting range
0-1
Enable
Disable
Default
0
Operation/procedure (Pattern 2)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
(Initial screen)
(Input screen)
Sim51-1 D/F TIMING
1:600dpi
50
2:1200dpi
50
2
Display items
1:600dpi
2:1200dpi
Sim51-1 D/F TIMING
2:1200dpi
50
[ 1- 99]
Setting range
1-99
61
61-1
Purpose
Function
(Purpose)
Section
Item
50
Default
50
Operation test/check
Used to test the operation of the LSU.
LSU
Operation
Operation/procedure
Pressing the [OK] key performs the LSU test.
51-2
Purpose
Function
(Purpose)
Section
Item
Adjustment
Used to adjust the contact pressure of paper onto the
resist roller in each section (copier paper feed section,
duplex paper feed section, SPF paper feed section).
(When the print image position varies greatly for the
paper or when a lot of paper jam troubles occur, the
adjustment is required.)
Paper transport (Discharge/Switchback/Transport)
Operation
Used to set the LSU to ON state and check that the sync signal
(HSYNC/) is outputted or not.
After operation for 30 sec, the result is displayed. (Interruption cannot
be made for 5 sec after starting the operation.)
(Initial screen)
(Executing screen)
Sim61-1 LSU CHECK
PRESS OK KEY
Sim61-1 LSU CHECK
Interruption is inhibited
during execution.
During execution,
[EXEC] is highlighted.
EXEC
EXEC
(Result screen/Normal) (Result screen/Abnormal)
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen)
(Input screen)
(Executing screen)
Sim51-2 RESIST ADJ.
1:BYPASS
50
2:TRAY1
50
3:TRAY2
50
1/3
50
Sim61-1 LSU CHECK
Sim61-1 LSU CHECK
COMPLETE
ERROR
EXEC
EXEC
63
63-1
Display items
1:BYPASS
2:TRAY1
3:TRAY2
4:TRAY3
5:TRAY4
6:DUPLEX
7:SPF(SIDE1)
8:SPF(SIDE2)
Content
Manual feed
1st cassette
2nd cassette
3rd cassette
4th cassette
Back print
SPF front surface
SPF back surface
Setting range
1-99
Default
50
Purpose
Function
(Purpose)
Section
Item
Adjustment/setting/operation data output/check
(display/print)
Used to check the result of shading correction. (The
shading correction data are displayed.)
Scanner (Exposure)
Operation
Operation/procedure
Pressing the [OK] key performs shading, and displays the result (center pixel).
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTERRUPT] key is inhibited.
AR-235/275 SIMULATION - 33
(Initial screen)
(Executing screen)
(Screen after execution
screen)
Sim63-1 SHADING
Sim63-1 SHADING
Sim63-1 SHADING
PRESS OK KEY
EXEC
EXEC
PRESS OK KEY
EXEC
65
65-5
40
63-7
Adjustment
Used to adjust the SPF white correction start pixel
position automatically.
This adjustment is performed after the lens unit is
replaced.
Scanner
Section
Operation
Item
Operation/procedure
Purpose
Function
(Purpose)
Used to check the operation panel.
Function
(Purpose)
Operation (screen/operation)
Section
Operation/procedure
Check the key input of the operation panel.
Press the keys displayed on LCD sequentially.
After completion of all key entries, "COMPLETE" is displayed.
(1)
(2)
(3)
Sim65-5 KEY CHECK
FAX
Sim65-5 KEY CHECK
COPY
Sim65-5 KEY CHECK
COMPLETE
Set the SPF unit OPEN, and press the [OK] key.
[ ] indicates the order number of the pixel of the white sheet for SPF
exposure correction in the SPF position.
If the adjustment is normally completed, "COMPLETE" is displayed
and data are written into the EEPROM.
In case of an abnormality, "ERROR" is displayed and no data is written
into the EEPROM.
The SPF white correction start pixel = Displayed pixel position - 34
If the simulation is executed with the SPF unit closed, an error is
resulted.
(Initial screen)
(Executing screen)
Interruption is inhibited
Sim63-7 SPF ADJ.
Sim63-7 SPF ADJ.
during execution.
WHITE ADJUST
WHITE ADJUST
During execution,
[EXEC] is highlighted.
EXEC
PRESS OK KEY
(Initial screen with the execution result displayed)
Normal end screen
Abnormal end screen
66
66-1
Purpose
Function
(Purpose)
Adjustment/Setting/Check
FAX related soft SW setting
Operation/procedure
Display FAX software SW on LCD, and set/change those with 10-key.
Note: Executable only when the FAX is installed.
66-2
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Initial set for the value of the FAX soft SW
Operation/procedure
Sim63-7 SPF ADJ.
WHITE ADJUST
COMPLETE
[160]
PRESS OK KEY EXEC
Sim63-7 SPF ADJ.
WHITE ADJUST
ERROR
[ 0]
PRESS OK KEY EXEC
Used to clear the FAX-related soft switches except for the line signal
adjustment value and the machine adjustment value and to set default
values (which differ depending on the country code separately
entered.)
Note: Executable only when the FAX is installed.
66-3
64
Purpose
Function
(Purpose)
64-1
Purpose
Function
(Purpose)
Section
Item
Adjustment/Setting/Check
FAX PWB memory check
Operation/procedure
Operation test/check
Used to check the operation of the printer function
(auto print operation).
Printer
Operation
Operation/procedure
Pressing the [START] key makes a print by 2 by 4 mode. After completion of printing, the menu returns to the initial menu.
Pressing the [CA] key cancels the simulation mode.
(Input screen)
(Executing screen)
Read/write can be checked for FAX PWB memory.
The check result is displayed separately for each memory.
1. Memory to be checked
DRAM
SRAM
Flash ROM
Program area
Memory area
Option memory
SUM check only
The memory size follows the
automatically detected value.
PAGE
2. Detailed procedure
1
2
"55H" is written to all the addresses of each memory, and the
address data are read in sequence to check that they were
properly written.
"AAH" is written to all the addresses of each memory, and the
address data are read in sequence to check that they were
properly written.
AR-235/275 SIMULATION - 34
3
"00H" is written to all the addresses of each memory, and the
address data are read in sequence to check that they were
properly written.
4 Perform checks 1 - 3 sequentially. If there is no abnormality, it is
"OK." If there is any abnormality, "NG" is notified to the error
address.
5 After completion of check, the memory is returned to the initial
state.
(CPU is not reset)
Interruption cannot be made during operation.
Adjustment/Setting/Check
Purpose
Print the screen memory contents
Function
(Purpose)
Operation/procedure
Used to input all image data (including confidential reception data,
remote send image, not-sent image) stored in image memory of the
FAX section.
The output image is remained even after outputting.
Note: Executable only when the FAX is installed.
Note: Executable only when the FAX is installed.
66-8
66-4
Purpose
Function
(Purpose)
Related soft
SW
66-7
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Signal send mode
Operation/procedure
SW5-5 to 8 (signals send level)
SW23-1 to 4 (RBT ON time)
SW23-5 to 8 (RBT OFF time)
SW43-1 to 5 (DTMF signal send time)
By setting the message No., the sound message is sent to the line and
the speaker of the body. (The message is repeated until the interruption command is provided by pressing the [BACK] key.)
Operation/procedure
By setting the message No., the signal is sent to the line and the
speaker of the body. (The signal is continuously sent until the interruption command is provided by pressing the [BACK] key.)
Message
number
1
The signal send level can be selected from 0dB or the soft SW set
value. However, the level setup is not required for 01, 31 - 35, the
selection may does not appear. After completion of the mode, the signal send level is returned to the soft SW set value before execution of
the mode.
Signal
number
01
26
27 to 30
31
32
33
34
35
Other than
the above
Send signal
Signal not send
7EH Flag signal
Tone signal
Pseudo-ringer sound
([ON HOOK] key ON)
Voice message (no sound)
Under the state where the ring back
tone can be sent to the line, keep
the sound composition IC volume to
0.
Ring back tone (no sound)
Under the state where the ring back
tone can be sent to the line, keep
the G/A volume to 0.
Dial pulse (make)
Maintain the make state with
keeping the condition to be able to
send to the dial pulse line.
Dial pulse (break)
Maintain the break state with
keeping the condition to be able to
send to the dial pulse line.
FFH
Send level
Selection menu
None
Yes
Yes
None
None
2
3
4
Voice message
"Hold the line a minute, please send fax."
(TEL/FAX voice response)
"Hold the line a minute."
(TEL/FAX voice response)
"Not around here, please send fax."
(TEL/FAX voice response)
"Ding Dong"
(Sound delivered when switching to remote reception)
Message No. 4 can be heard by an external telephone speaker.
Note: Executable only when the FAX is installed.
66-10
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Image data memory clear
Operation/procedure
Used to clear all image data (including confidential reception data)
stored in image memory of the FAX section.
None
The management table is also cleared (initialized) at the same time.
Note: Executable only when the FAX is installed.
1: 0dB
2: Soft SW
1: 0dB
2: Soft SW
Yes
Note: Executable only when the FAX is installed.
66-11
Purpose
Function
(Purpose)
Adjustment/Setting/Check
300bps signals send
Operation/procedure
By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [BACK] key.)
The signal send level can be selected from 0dB or the soft SW set
value.
The signal send level is returned to the soft SW set value before execution of the mode after completion of the mode.
66-6
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Voice Message send
Number
1
2
3
Adjustment/Setting/Check
Printing the confidential password
Signal
No signal (CML ON)
11111
11110
Number
4
5
6
Note: Executable only when the FAX is installed.
Operation/procedure
The confidential ID table (confidential BOX numbers, confidential BOX
names, and confidential password) is printed.
The confidential data of My company mode is printed separately.
Note: Executable only when the FAX is installed.
AR-235/275 SIMULATION - 35
Signal
00000
010101
00001
66-13
Adjustment/Setting/Check
Send test and adjustment of the dial pulse and
DTMF signal.
SW53-1 to 4 (DTMF high group end level)
SW53-5 to 8 (DTMF low group send level)
SW67-1 to 4 (DP 10PPS make time)
SW67-5 to 8 (DP 10PPS make time)
Operation/procedure
Purpose
Function
(Purpose)
Related soft SW
The send test of dial pulse and DTMF signal is performed and the
make time adjustment of dial pulse and the DTMF signal send level
adjustment are performed if necessary.
The DTMF signal of the specified dial number is delivered until the
interruption command is provided by pressing the [BACK] key.) When
another dial number is specified during delivery of the signal, the new
dial number is delivered.
The signal send level is returned to the soft SW set value before execution of the mode after completion of the mode.
Note: Executable only when the FAX is installed.
66-21
Purpose
Function
(Purpose)
Adjustment/Setting/Check
FAX information print
1. Dial pulse (10pps) send test
Operation/procedure
2. Dial pulse (20pps) send test
The following FAX information is printed.
• Used to set the make time. By performing the test, the registered
dial pulse of max. 100 digits can be sent from the line.
• When "*" and "#" are included in the registered dial number, they are
disregarded and the number is not processed as a dial.
• The make time set in the dial test is written into the corresponding
soft SW.
• Default: 1 2 3 4 5 6 7 8 9 0
Operate the [ ← ] [ → ] key in DP dial selection menu to switch.
(Time before pulse delivery can be changed as 2sec → 4sec →
8sec.)
A
B
C
D
Print information
User switch list
Soft SW list
Dump list
System error
E
Protocol monitor
3. DTMF signal send test
Details
Used to print the system error log (error
number and time). For this operation, the
system error log is always stored as the
ring buffer in the SRAM 256byte area.
Regardless of soft SW19-1 status, the
protocol monitor of the preceding
communication is printed. (Printing is
allowed at any time before starting the
next communication.) For this operation,
the protocol monitor of one
communication is always buffered.
• Set the signal send level to 0dB or the soft SW set value.
Used to set the high level group and the low level group of DTMF
signal send level. By executing the test, DTMF signal is sent from
the line to a recorded dial number of max. 100 digits.
Note: Executable only when the FAX is installed.
• The high group/low group value of the DTMF signal send level set in
the dial test is written into the corresponding soft SW.
66-22
• Default: 1 2 3 4 5 6 7 8 9 * 0 #
In the PB dial select menu, press [←][→] keys to select.
Pressing the [CLEAR] key during the operation clears the input
value and returns to the value input menu.
• Max. 100 digits can be assigned to each dial (0 - 9, *, #). While the
default value is displayed at first, a desired value can be entered and
the entered value is stored on the FAX side until the menu is canceled.
• After completion of the mode, the signal send level is returned to the
soft SW set value before execution of the mode.
Make time
Break time
DTMF signal
adjustment
1ms for input value of 1. Adjust so that the dial pulse
make rate is within 33±3%. (For North America,
40±3%.)
Dial pulse make rate =
Make time / (Make time + Break time)
It is obtained from the formula below and
automatically set.
PPS = 1000 / (make time + break time)
The signal send levels are classified into the high
group and the low group. The send level is 0.5dB for
each 1 of input value.
Note: Executable only when the FAX is installed.
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
Handset sound volume adjustment
SW13-1 to 2
Operation/procedure
By selection of the sound volume number, the sound volume of the
handset can be set or changed. The set value is written into the soft
SW.
During execution of the simulation, the reply sound message for auto
selection of TEL/FAX, "Hold the line for a while," is delivered.
Sound volume number
1
2
3
Sound volume
Small
Medium
Large
Note: Executable only when the FAX is installed.
66-30
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Recognize TEL/LIU state change.
Operation/procedure
66-17
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
DTMF signal send
SW53-1 to 4 (DTMF high group end level)
SW53-5 to 8 (DTMF low group send level)
Operation/procedure
Set the signal send level to 0dB or the soft SW set value, and specify
one dial to be delivered to.
When the relay state of the polarity reverse relay, the handset hook
switch, or the external telephone hook switch is changed, the content
of change is displayed regardless of the soft SW setup. The display of
change is kept until an interruption command is supplied by pressing
the [BACK] key.
Check signal
HS2
HS1
RHS
EXHS
Notification contents
Signal low
Signal high
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Note: Executable only when the FAX is installed.
AR-235/275 SIMULATION - 36
1. Sound kinds pattern
66-32
Adjustment/Setting/Check
Purpose
Receive data check
Function
(Purpose)
Operation/procedure
The data received from the line are checked to insure that the following
reception data are identical to the judgment data. If identical, "OK" is
notified. If not, "NG."
A judgment is made according to the reception start data. Continuous
coincidence is required.
Receive speed
Receive data
Number of judgment data
300bps
00
100
1
2
3
4
Note: Executable only when the FAX is installed.
5
66-34
6
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
Communication time measurement display
Operation/procedure
The send/receive test is performed, and the time required for send/
receive of the image data in the test is measured and displayed.
Measuring
range
Send
Receive
Mode when measuring
How to check the time
Measuring unit
Communication
: Memory send
means
: Normal Character
Picture quality
: Lighter
Density
: ON
ECM
: OFF
Sender information
From flag reception before sending of
image data until sending of RCP frame
From flag reception before reception of
image data until reception of RCP frame
Used to make communication not in a
simulation process but in the normal screen
and measure the time.
Enter the simulation for communication time
check and check the time.
msec
When there are two or more send/receive operations of image data in
one communication, only the time of the last send/receive data near
the end is measured.
Note: Executable only when the FAX is installed.
1
2
3
NS
NS
S
S
M
M
L
L
Sound
volume
Pattern
01 to 35
01 to 35
Call sound
Lline monitor sound
(Test sound :
Communication
signal sound)
On hook
(Test sound :
Communication
signal sound)
Read complete
sound
Communication
end sound
DTMF signal send
sound
Setting
Disable
S
M
L
01 to 35
NS
S
M
L
01 to 35
NS
S
M
L
01 to 35
NS
S
M
L
01 to 35
NS=No Sound S=Small M=Medium L=Large
Sound
volume
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
1
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
2
M
M
M
M
M
VR set value
3 4 5 6
L
L
L
L
M
M
M
M
L
L
L
M
M
M
L
L
M
M
L
M
S
S
S
S
M
M
M
M
L
Sound
7 volume 1
20
21
22
23
L
24
25
26
27
L
28
29
30
L
31
32
L
33
L
34
35
2
S
S
S
S
S
S
VR set value
3 4 5 6
M L
M
L
M
M L
M
M
S M L
S M
L
S M
S
M L
S
M
S
M
S M L
S M
S
M
S M
7
L
L
L
L
L
L
L
L
L
L
L
L
S=Small M=Medium L=Large
Note: Executable only when the FAX is installed.
66-38
66-37
Purpose
Function
(Purpose)
Related soft SW
Sound volume set value
2. Sound volume pattern
SW10-1
Setup on the user
side when executing
communication
0
Sound kinds
(Test sound)
Purpose
Function
(Purpose)
Adjustment/Setting/Check
Speaker sound volume adjustment
SW 86-1, 2 (call sound)
SW 85-1, 2 (line monitor sound)
SW 84-1, 2 (on hook)
SW 88-1, 2 (read end sound)
SW 89-1, 2 (communication end sound)
SW 87-1, 2 (DTMF send sound)
SW75-1, 2 (send end sound length)
SW75-3, 4 (receive end sound length)
Operation/procedure
The following test sound is delivered to the line and the speaker to
adjust the sound kind and volume.
The send level to the line is the set value of soft SW.
The set values of the selected sound kind and volume are written to
each soft SW.
Adjustment/Setting/Check
Time setting/check
Operation/procedure
Read/write the time (year, month, day, min., sec.) on RTC of FAX
PWB.
Note: Executable only when the FAX is installed.
66-41
Purpose
Function
(Purpose)
Related soft SW
Adjustment/Setting/Check
CI signal check
SW12-6 to 7, SW55-1 to 7
Operation/procedure
The call signal from CI pin is detected to deliver the call sound to the
line and the speaker. The volume of call sound follows the soft SW.
Signal detection and delivery of pseudo-call sound at detection are
executed until the interruption command is provided by pressing the
[BACK] key.
Note: Executable only when the FAX is installed.
AR-235/275 SIMULATION - 37
Note: Executable only when the FAX is installed.
66-50
Japan only
Note
Adjustment/Setting/Check
Purpose
FAST SRAM clear
Function
(Purpose)
Operation/procedure
66-53
Purpose
Function (Purpose)
SRAM data in FAST area is intialized.
Note: Executable only when the FAX is installed.
Adjustment/Setting/Check
SRAM backup
Operation/procedure
Used to save the SRAM data to the expanded memory and read it.
66-51
Purpose
Function
(Purpose)
Related soft SW
When reading, however, the current FAX software version and the
header FAX software version are collated together. If they are not identical, reading cannot be performed.
Adjustment/Setting/Check
Signal detection check
1. Back-up targets
SW13-3, 4 (call sound volume)
SW32-1 to 4 (Distinctive Ring)
SW12-6, 7 (CI detection pattern)
(00:4 Sine wave 10:3 Sine wave 01:2 Sine wave)
SW26-3, 4 (speaker volume)
SW35-3, 4 (CI extinction maximum OFF time)
SW51-7, 8 (BT detection cycle)
SW52-1, 2 (BT/DT detection level)
SW55-1 to 7 (detection possible time of CI
signal)
SW56-5, 6 (DT, BT filter efficiency)
SW56-7 (DP, BT detection level)
Operation/procedure
The detection test of signals is performed and the test result is displayed.
1. Detected signal
Detected in off-hook.
Detected in off-hook.
CI, CNG, FNET, DTMF
BusyTone, CNG
DialTone, CED
SDT, flag, DTMF
2. Display combination
Combination
CI, CNG, FNET
CED, CNG, BusyTone, DTMF
CED, Flag, BusyTone
CED, Flag, DialTone
CED, Flag, SDT
Hook state
On hook
Off hook
The display conforms to the detection frequency and pattern specified
according to each country information.
The detection signal level conforms to the range set by the soft SW.
The detected table and routines are shared with actual communications.
Note: Executable only when the FAX is installed.
66-52
Purpose
Function (Purpose)
Data out of target
Registration information, soft SW information,
FAX counter information (Information for each
department is not required.)
Image management information,
communication reservation information
2. Internal process
SRAM stack processing
1) Used to check if the installed expansion memory is ready to use.
If an expanded memory is available, write the target data of the
SRAM.
2) After completion of writing, management information is written to
the management information block.
3) For the management information, refer to the table below.
However, the FAX program version No. area is written into the data
version no. area (FFF0 - FFFF).
Lowest
address
CI displays the detected ring pattern simultaneously.
A
B
C
D
E
Target data
0000 to
FFAF
FFB0 to
FFCF
FFD0 to
FFDF
FFE0 to
FFEF
FFF0 to
FFF1
FFF2 to
FFF3
FFF4 to
FFF7
FFF8 to
FFFB
FFFC to
FFFF
Area name
Expanded
memory
Upper 2MB
Content
←
Reserved
TEST pattern
ROM data
name
Data version
No.
Write
complete FLG
SRAM clear
flag
Start address
End address
SUM
TEST pattern
*Reference
REGISTRATION
ASCII 16 Byte
ASCII 16 Byte
FAX program
version No.
ERASE=H'FFFF
Completion=H'0000
Clear/No=H'0000
Clear/Yes=H'0001
Data start address
←
Invalid
Data end address
←
Data check sum
←
←
*TEST pattern
Adjustment/Setting/Check
Pseudo-ringer check
Recognized that the card normally reads the next data.
Operation/procedure
• The pseudo-ringer sound is provided in both of the main speaker
and the external telephone.
• Holding the handset or the external telephone set stops the bell.
Hanging it restarts ringing. This operation is continued until the interruption command is supplied by pressing the [BACK] key.
• The LCD displays the TEL/LIU status, indicating the HOOK condition.
• During sending the pseudo-ringer, RBT (Ring Back Tone) is delivered to the line.
• The bell is ON for 1sec and OFF for 2sec. When off-hooking with the
bell ON, the HOOK detection at pseudo-ringer ringing can be
checked. When off-hooking with the bell OFF, the HOOK detection
before pseudo-ringer ringing can be checked.
Address
FFB0
FFB2
FFB4
FFB6
FFB8
FFBA
Date
0001
0002
0004
0008
0010
0020
Address
FFBC
FFBE
FFC0
FFC2
FFC4
FFC6
Date
0040
0080
0100
0200
0400
0800
Address
FFC8
FFCA
FFCC
FFCE
–
–
Date
1000
2000
4000
8000
–
–
Additional process when turning on the power
In normal cases, when installation of an expanded memory is detected
after turning ON the power, the expanded memory is cleared. When,
however, there are some SRAM data in the expanded memory, it must
not be cleared. When the ROM data name (FED0 - FFDF) in the management information of the expanded memory is "REGISTRATION,"
the expanded memory is not cleared.
AR-235/275 SIMULATION - 38
Process when reading the expanded memory
1) After checking the data in the management information, reading
from the expanded memory and writing into the SRAM are performed.
Sim67-14 FLASH D/L
PRESS OK KEY
Sim67-14 FLASH D/L
Please Send Data
READY
Sim67-14 FLASH D/L
PROGRAM
RECEIVE
2) After completion of writing into the SRAM, the expanded memory
is initialized for normal use again.
3) After completion of initializing the expanded memory, the SRAM
RESTORE operation of the simulation is terminated.
(Normal end screen)
(Abnormal end screen)
Sim67-14 FLASH D/L
Sim67-14 FLASH D/L
COMPLETE
FAILED
Remark 1: SRAM data saving procedure
1) Before saving, install the expanded memory to be used. (During
power OFF)
2) In the SRAM backup menu (66-53), SRAM BACK UP is selected,
and the process to save SRAM data into the expanded memory is
executed.
3) After completion of saving, turn off the power.
Remark 2: SRAM data reading procedure
1) Install the expanded memory into which data are written according
to the above procedures. (During power OFF)
2) In the SRAM backup menu (66-53), SRAM RESTORE is selected
to write the SRAM data which was saved into the expanded memory into the SRAM of the FAX board.
Note: Executable only when the FAX is installed.
(Flash Device)
(Processing state)
PROGRAM
RECEIVE
BOOTROM
ERASE
PS KANJI FONT
WRITE
ESC/P KANJI FONT
VERIFY
OPTION FONT
Press the [CA] key to cancel the simulation and reset.
Note: Executable only when the PCL is installed.
67-17
Function (Purpose)
Used to clear NVRAM.
Operation/procedure (Pattern 7)
67
Pressing the [OK] key displays the confirmation message.
Press the [OK] key again to clear. Press the [BACK] key to interrupt
clearing.
67-11
Purpose
Function (Purpose)
If there is no abnormality after Clear operation, "COMPLETE" is displayed. If there is any abnormality, "ERROR" is displayed.
(Initial screen)
(Process check screen) (Executing screen)
Setting
Used to set the Select-IN signal.
Operation/procedure (Pattern 1)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Sim67-11 SELECT-IN
SELECT-IN SIGNAL 0
(0:ON 1:OFF)
[ 0- 1]
Setting range
Default
Sim67-17 NVRAM CLR.
NVRAM CLEAR
Sim67-17 NVRAM CLR.
NVRAM CLEAR
Sim67-17 NVRAM CLR.
NVRAM CLEAR
PRESS OK KEY
ARE YOU SURE?
NOW DOING...
(Normal end screen)
0
0-1
0
(Abnormal end screen)
Sim67-17 NVRAM CLR.
NVRAM CLEAR
Sim67-17 NVRAM CLR.
NVRAM CLEAR
COMPLETE
PRESS OK KEY
ERROR
PRESS OK KEY
Note: Executable only when the PCL is installed.
Note: Executable only when the PCL is installed.
67-14
67-18
Function (Purpose)
Used to check write/comparison of flash
programs.
Function (Purpose)
Used to clear the data area for FLASH ROM
Network Scanner Application.
Operation/procedure
Operation/procedure (Pattern 7)
Download PCL.
Pressing the [OK] key displays the confirmation message.
Pressing the [OK] key displays "Please Send Data" "Ready" and the
data is sent from the PC under the MS-DOS command of FCOPY and
the file name.
Press the [OK] key again to clear. Press the [BACK] key to interrupt
clearing.
Used to overwrite and check the flash device while displaying its process status.
After completion, the result is displayed.
(It takes a little time to display READY.)
If there is no abnormality after Clear operation, "COMPLETE" is displayed. If there is any abnormality, "ERROR" is displayed.
(Initial screen)
(Process check screen) (Executing screen)
Sim67-18 APP. CLR.
APP. DATA CLEAR
PRESS OK KEY
(Normal end screen)
Sim67-18 APP. CLR.
APP. DATA CLEAR
Sim67-18 APP. CLR.
APP. DATA CLEAR
ARE YOU SURE?
NOW DOING...
(Abnormal end screen)
Sim67-18 APP. CLR.
APP. DATA CLEAR
Sim67-18 APP. CLR.
APP. DATA CLEAR
COMPLETE
PRESS OK KEY
ERROR
PRESS OK KEY
Note: Executable only when the PCL is installed.
AR-235/275 SIMULATION - 39
67-20
Function (Purpose)
Used to check the network connection when
the scan option is installed.
Operation/procedure
The network scanner is checked.
When [OK] key is pressed, "Please Send Data" and "READY" are displayed, and then ftp is booted from MS-DOS.
Put the file name, and data are transmitted from the PC.
The process is displayed. Check the display.
After completion, the result is displayed.
(It takes a little time to display READY.)
(1)
(2)
Sim67-20 SCAN TEST
PRESS OK KEY
(Normal end screen)
Sim67-20 SCAN TEST
Please Send Data
READY
(3)
Sim67-20 SCAN TEST
TEST DATA
RECEIVE
(Abnormal end screen)
Sim67-20 SCAN TEST
Sim67-20 SCAN TEST
COMPLETE
ERROR
(TEST DATA)
TEST DATA
(Process status)
RECEIVE
TESTING
Pressing [CA] key cancels the simulation resets the operation.
Note: Executable only when PCL and NIC are installed.
AR-235/275 SIMULATION - 40
[9] TROUBLE CODE LIST
1. List
Trouble
code
Main Sub
code code
E1
00
10
11
12
13
14
15
16
17
80
81
82
84
88
E7
F1
F2
F5
F6
02
10
11
12
00
01
06
08
11
15
02
04
02
00
10
80
81
82
84
88
99
Trouble
detection
Trouble contents
IMC board communication trouble
IMC board trouble
IMC ASIC error
IMC CODEC error
IMC board flash ROM error
IMC board Work RAM error
IMC board Page Memory error
IMC board image compression store
memory error
IMC board smoothing IC error
IMC PWB communication trouble
(protocol)
IMC PWB communication trouble (Parity)
IMC PWB communication trouble
(Overrun)
IMC PWB communication trouble
(Framing)
IMC PWB communication trouble (Timeout)
LSU trouble
Shading trouble (black correction)
Shading trouble (white correction)
Shading trouble
Finisher communication trouble
Finisher jogger shift trouble
Finisher shift motor abnormality
Finisher staple shift motor trouble
Pusher motor trouble
Finisher elevator motor trouble
Toner supply failure
Identification error
Model error
Type error
Destination error
Data abnormality
Misc error
Copy lamp lighting abnormality
F6-**: MCU-FAX communication trouble
FAX control PWB trouble
FAX control PWB communication trouble
(Protocol)
FAX control PWB communication trouble
(Parity)
FAX control PWB communication trouble
(Over-run)
FAX control PWB communication trouble
(Framing)
FAX control PWB communication trouble
(Timeout)
Machine-FAX board language error
Trouble
code
Main Sub
code code
F9
00
10
80
81
MCU
82
84
88
H2
H3
H4
H5
L1
L3
L4
L6
L8
U2
FIN
U7
U9
99
00
00
00
01
02
00
00
01
11
10
01
04
11
12
20
40
00
00
80
81
82
84
88
MCU
CE
99
00
01
02
03
04
05
EE
EL
EU
PF
00
AR-235/275 TROUBLE CODE LIST - 1
Trouble contents
F9-**: MCU-PRT communication trouble
Printer PWB trouble
Printer PWB communication trouble
(Protocol)
Printer PWB communication trouble
(Parity)
Printer PWB communication trouble
(Overrun)
Printer PWB communication trouble
(Framing)
Printer PWB communication trouble
(Timeout)
Machine-PCL board language error
Thermistor open detection
Heat roller abnormally high temperature
Heat roller abnormally low temperature
5 continuous T10D(T20D) not-reaching
JAM
Fusing thermistor abnormality
Scanner feed trouble
Scanner return trouble
Main motor lock
Shifter motor trouble
Polygon motor lock trouble
Zero cross detection error
EEPROM communication error
Counter check sum error
Adjustment value check sum error
Machine speed code data error
CRUM chip communication error
RIC communication trouble
U9-**: MCU-OPE communication trouble
Operation control PWB communication
trouble (Protocol)
Operation control PWB communication
trouble (Parity)
Operation control PWB communication
trouble (Overrun)
Operation control PWB communication
trouble (Framing)
Operation control PWB communication
trouble (Time-out)
Operation panel language error
The other communication error has
occurred.
The print server card (AR-NC3D) is not
installed or defective.
The specified mail server or the FTP
server is not found.
The specified server does not
correspond during image transmission.
The entered account name of the FTP
server or the password is invalid.
The entered directory of the FTP server
is invalid.
Developer adjustment trouble (Overtoner abnormality)
Developer adjustment trouble (Undertoner abnormality)
RIC copy inhibit signal received
Trouble
detection
MCU
OPE
Network
Network
Network
Network
Network
Network
2. Self diagnostics
Trouble
code
Main Sub
code code
E1
00
Details of trouble
Content
Details
Cause
Check
and
remedy
10
Content
Details
Cause
Check
and
remedy
11
12
13
14
Trouble
code
Main Sub
code code
E1
15
Content
Details
Cause
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
Cause
Check
and
remedy
Remarks
E1-**: MCU-IMC communication trouble
Communication establishment error/
framing/parity/protocol error
IMC PWB connector disconnection
IMC PWB MCU PWB harness failure
Motherboard connector pin breakage
IMC PWB ROM defect, data failure
Check the connectors and harness of the
IMC PWB and MCU PWB.
Check the grounding of the copier.
Check the ROM of the IMC PWB.
IMC PWB trouble
Communication trouble between MCU and
IMC PWB
IMC PWB connector disconnection
IMC PWB MCU PWB harness failure
Motherboard connector pin breakage
IMC PWB ROM defect, data failure
Check the connectors and harness of the
IMC PWB and MCU PWB.
Check the grounding of the copier.
Check the ROM of the IMC PWB.
IMC board ASIC error
ASIC abnormality on IMC board
IMC board abnormality
Replace the IMC PWB.
IMC board CODEC IC error
CODEC IC (JBIG chip) abnormality on
IMC board
IMC board abnormality
Replace the IMC PWB.
JBIG IC abnormality
IMC board flash ROM error
Flash ROM abnormality on IMC board
IMC board abnormality
Replace the IMC PWB.
"When the program download is
abnormally terminated, a error may occur.
In this case, download the program again."
Program ROM abnormality
IMC board Work RAM error
IMC extended compression memory
module installation error
IMC extended compression memory
access error
IMC expanded memory module
installation trouble
IMC expanded memory module trouble
IMC expanded memory contact trouble
IMC board abnormality
Check installation of the expanded
memory module. (Spec: Added to Slot 1.)
Replace the expanded memory module.
Replace the IMC PWB.
Extend memory abnormality for
compressed image store (DIMM module)
16
Details of trouble
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
17
80
Cause
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Content
Details
Cause
Check
and
remedy
81
Content
Details
Cause
Check
and
remedy
82
Content
Details
Cause
Check
and
remedy
AR-235/275 TROUBLE CODE LIST - 2
IMC board Page Memory error
IMC Page Memory abnormality
IMC board abnormality
Replace the IMC PWB.
Print Buffer Memory abnormality
IMC board compression image store
memory error
IMC standard compression memory
access error
IMC board abnormality
Replace the IMC PWB.
IMC board smoothing IC error
IMC smoothing IC abnormality
IMC board abnormality
Replace the IMC PWB.
IMC PWB communication trouble
(protocol)
Communication trouble between MCU and
IMC PWB (Protocol error)
IMC PWB connector disconnection
IMC PWB MCU PWB harness failure
Motherboard connector pin breakage
IMC PWB ROM defect, data failure
Check the connectors and harness of the
IMC PWB and MCU PWB.
Check the grounding of the copier.
Check the ROM of the IMC PWB.
IMC PWB communication trouble (Parity)
Communication trouble between MCU and
printer IMC (Parity error)
IMC PWB connector disconnection
IMC PWB MCU PWB harness failure
Motherboard connector pin breakage
IMC PWB ROM defect, data failure
Check the connectors and harness of the
IMC PWB and MCU PWB.
Check the grounding of the copier.
Check the ROM of the IMC PWB.
IMC PWB communication trouble
(Overrun)
Communication trouble between MCU and
IMC PWB (Overrun error)
IMC PWB connector disconnection
IMC PWB MCU PWB harness failure
Motherboard connector pin breakage
IMC PWB ROM defect, data failure
Check the connectors and harness of the
IMC PWB and MCU PWB.
Check the grounding of the copier.
Check the ROM of the IMC PWB.
Trouble
code
Main Sub
code code
E1
84
Details of trouble
Content
Details
Cause
Check
and
remedy
88
Content
Details
Cause
Check
and
remedy
E7
02
Content
Details
Cause
Check
and
remedy
10
Content
Details
Cause
11
Check
and
remedy
Content
Details
Cause
Check
and
remedy
IMC PWB communication trouble
(Framing)
Communication trouble between MCU and
IMC PWB (Framing error)
IMC PWB connector disconnection
IMC PWB MCU PWB harness failure
Motherboard connector pin breakage
IMC PWB ROM defect, data failure
Check the connectors and harness of the
IMC PWB and MCU PWB.
Check the grounding of the copier.
Check the ROM of the IMC PWB.
IMC PWB communication trouble (Timeout)
Communication trouble between MCU and
IMC PWB (Time-out error)
IMC PWB connector disconnection
IMC PWB MCU PWB harness failure
Motherboard connector pin breakage
IMC PWB ROM defect, data failure
Check the connectors and harness of the
IMC PWB and MCU PWB.
Check the grounding of the copier.
Check the ROM of the IMC PWB.
LSU trouble
BD signal from LSU is not detected in a
constant cycle. (Kept OFF or ON)
LSU connector or LSU inside harness
trouble or disconnection
Polygon motor rotation abnormality
Laser does not illuminate.
MCU PWB failure
Check for disconnection of the LSU
connector.
Check the LSU operation with SIM 61-1.
Check that the polygon motor rotates
normally.
Check laser LED lighting.
LSU replacement
Replace the MCU PWB.
Shading trouble (black correction)
CCD black reference plate scan level
abnormality when the copy lamp turns off.
Flat cable installation failure to CCD unit
CCD unit error
Check flat cable installation to the CCD
unit.
Check CCD unit.
Shading trouble (white correction)
Improper CCD white reference plate
reading level for copy lamp lighting
Flat cable installation failure to CCD unit
"Dirt on the mirror, lens, and reference
white plate"
Copy lamp operation error
CCD unit abnormality
MCU PWB abnormality (Occurred in the
SPF scan position.)
"Clean the mirror, the lens, and the
reference white plate."
Check the copy lamp light quantity and its
operation. (SIM 5-3)
Check CCD unit.
Check MCU PWB.
Trouble
code
Main Sub
code code
E7
12
Details of trouble
Content
Details
Cause
Check
and
remedy
F1
00
Content
Details
Cause
Check
and
remedy
01
Content
Details
Cause
06
Check
and
remedy
Content
Details
Cause
08
Check
and
remedy
Content
Details
Cause
Check
and
remedy
AR-235/275 TROUBLE CODE LIST - 3
Shading trouble
White correction is not completed in the
specified number of times.
Flat cable installation failure to CCD unit
"Dirt on the mirror, lens, and reference
white plate"
Copy lamp lighting trouble
CCD unit abnormality
MCU PWB abnormality
"Clean the mirror, the lens, and the
reference white plate."
Check the copy lamp light quantity and its
operation. (SIM 5-3)
Check CCD unit.
Check MCU PWB.
Finisher communication trouble
Communication line test error occurs when
power is turned on or after the exit of a
simulation mode.
Error in Finisher communication
Connection trouble or disconnection of the
connector and harness between the body
and the finisher.
Finisher control PWB trouble
Control PWB failure
Malfunction by noises
Turn off/of the power to cancel the trouble.
Check connector/harness of
communication line
Replace the finisher control PWB.
Side guide plated home position error
The side guide plate cannot return to the
home position.
Side guide plate drive motor abnormality
Side guide plate home position sensor
abnormality
Use SIM3-3-1 to check the side guide
plate motor operation.
Offset motor trouble
When the offset motor of the finisher is
driven it does not reach the specified
position.
Offset motor abnormality
Offset motor origin sensor abnormality
Finisher PWB abnormality
Use SIM 3-3-6 to check the offset motor
operation.
Staple motor error
The staple motor cannot return to the
home position.
Staple motor abnormality
Staple motor home position sensor
abnormality
Staple unit abnormality
Use SIM 3-3-7 to check the staple motor
operation.
Trouble
code
Main Sub
code code
F1
11
Details of trouble
Content
Details
Cause
15
Check
and
remedy
Content
Details
Cause
F2
02
Check
and
remedy
Content
Details
Cause
04
Check
and
remedy
Content
Details
Cause
Check
and
remedy
Rear edge plate home position error
The rear edge plate cannot return to the
home position.
Rear edge plate drive motor abnormality
Side guide plate home position sensor
abnormality
Finisher PWB abnormality
Use SIM 3-3-2 to check the rear edge
plate motor operation.
Finisher lift-up motor trouble
The finisher lift-up motor does not reach
the specified position.
Lift-up motor abnormality
Lift-up motor upper limit sensor
abnormality
Finisher PWB abnormality
Use SIM 3-3-5 to check the lift-up motor
operation.
Trouble
code
Main Sub
code code
F5
02
Content
Details
Cause
Check
and
remedy
Remarks
F6
00
Content
Details
Cause
Toner supply failure
The value judged from the actual toner
supply hysteresis differs greatly from the
toner sensor value.
Developing unit trouble
Toner supply abnormality caused by
installation of unpacked toner cartridge
Replace the developing unit
Use SIM 25-1 to perform DV stirring.
Check
and
remedy
10
Identification error
Model error
Type error
Destination error
Data abnormality
Misc error
Identification error
When the CRUM trademark differs.
When the CRUM company code differs.
Model error
When the boot program model code does
not match with the CRUM model
information.
Type error
When the CRUM type is other than
[Genuine/Conversion/Production rotation].
Destination error
The destination of the body differs from
that of the CRUM.
Data abnormality
The initial check information includes an
erroneous value.
When the max. toner supply time is 00:
When the print hard stop is 00:
CRUM chip failure
Erroneous developing unit
Replace the CRUM chip.
Replace the developing unit
Details of trouble
Content
Details
Cause
Check
and
remedy
80
Content
Details
Cause
Check
and
remedy
AR-235/275 TROUBLE CODE LIST - 4
Copy lamp lighting abnormality
The copy lamp does not light up.
Copy lamp error
Copy lamp harness abnormality
CCD PWB harness abnormality
Check the copy lamp (SIM 5-3)
When the lamp lights:
Check the harnesses and connectors
between the CCD unit and the MCU PWB.
When the lamp does not light:
Check the harness and connector
between the copy lamp and the MCU
PWB.
Replace the copy lamp unit.
Replace the MCU PWB.
Copy lamp disconnection
Cable is not attached.
F6-**: MCU-FAX communication trouble
Communication establishment error/
framing/parity/protocol error
FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
Check connector/harness of FAX control
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
FAX control PWB trouble
Communication trouble between MCU and
FAX control PWB
FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
Check connector/harness of FAX control
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
FAX control PWB communication trouble
(Protocol)
Communication trouble between MCU and
FAX control PWB (Protocol error)
FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
Check connector/harness of FAX control
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
Trouble
code
Main Sub
code code
F6
81
Details of trouble
Content
Details
Cause
Check
and
remedy
82
Content
Details
Cause
Check
and
remedy
84
Content
Details
Cause
Check
and
remedy
88
Content
Details
Cause
Check
and
remedy
99
Content
Details
Cause
Check
and
remedy
FAX control PWB communication trouble
(Parity)
Communication trouble between MCU and
FAX control PWB (Parity error)
FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
Check connector/harness of FAX control
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
FAX control PWB communication trouble
(Over-run)
Communication trouble between MCU and
FAX control PWB (Overrun error)
FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
Check connector/harness of FAX control
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
FAX control PWB communication trouble
(Framing)
Communication trouble between MCU and
FAX control PWB (Framing error)
FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
Check connector/harness of FAX control
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
FAX control PWB communication trouble
(Timeout)
Communication trouble between MCU and
FAX control PWB (Timeout error)
FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
Check connector/harness of FAX control
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
Machine-FAX board language error
The machine language setup does not
coincide with the FAX board language
setup.
FAX board correction error
SIM setup error
Check the firmware of the FAX board and
the combination of the panel screen data,
and download the correct version, if
necessary.
Check the machine language information.
(Machine language setup: SIM 26-22)
Trouble
code
Main Sub
code code
F9
00
Details of trouble
Content
Details
Cause
Check
and
remedy
10
Content
Details
Cause
Check
and
remedy
80
Content
Details
Cause
Check
and
remedy
81
Content
Details
Cause
Check
and
remedy
AR-235/275 TROUBLE CODE LIST - 5
F9-**: MCU-PRT communication trouble
Communication establishment error/
framing/parity/protocol error
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB trouble
Communication trouble between MCU and
printer PWB
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Protocol)
Communication trouble between MCU and
printer PWB (Protocol error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Parity)
Communication trouble between MCU and
printer PWB (Parity error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Trouble
code
Main Sub
code code
F9
82
Details of trouble
Content
Details
Cause
Check
and
remedy
84
Content
Details
Cause
Check
and
remedy
88
Content
Details
Cause
Check
and
remedy
99
Content
Details
Cause
Check
and
remedy
H2
00
Content
Details
Cause
Check
and
remedy
Remarks
Printer PWB communication trouble
(Overrun)
Communication trouble between MCU and
printer PWB (Overrun error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Framing)
Communication trouble between MCU and
printer PWB (Framing error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Printer PWB communication trouble
(Timeout)
Communication trouble between MCU and
printer PWB (Timeout error)
Printer PWB connector disconnection
Harness trouble between the printer PWB
and the MCU PWB
Motherboard connector pin breakage
Printer PWB ROM trouble/Data
disturbance
Check the connectors and harness of the
printer PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on printer PWB.
Machine-PCL board language error
The machine language setup does not
coincide with the PCL board language
setup.
PCL board connection error
SIM setup error
Check the firmware of the PCL board and
the combination of the panel screen data,
and download the correct version, if
necessary.
Check the machine language information.
(Machine language setup: SIM 26-22)
Thermistor open detection
Thermistor open detection
Fusing unit not installed
Thermistor defect
Control PWB failure
Fusing section connector contact failure
Fusing unit not installed
Check the harness and the connector of
the thermistor and the MCU.
Clear the display of self-diagnostics with
SIM 14.
Thermistor open
Trouble
code
Main Sub
code code
H3
00
Details of trouble
Content
Details
Cause
Check
and
remedy
H4
00
Content
Details
Cause
Check
and
remedy
H5
01
Content
Details
Cause
Check
and
remedy
02
Content
Details
Cause
Check
and
remedy
AR-235/275 TROUBLE CODE LIST - 6
Heat roller abnormally high temperature
The fusing temperature is over 220°C.
Thermistor defect
Control PWB failure
Fusing section connector contact failure
Check the heater lamp blinking with SIM 52.
When the lamp blinks normally:
Check the thermistor and the harness.
Check the MCU PWB thermistor input
circuit.
If lamp lights and stays lit:
Check the power PWB and the MCU PWB
lamp control circuit.
Clear the display of self-diagnostics with
SIM 14.
Heat roller abnormally low temperature
The setup temperature (about 90°C is not
reached within the specified time (about
35sec) from turning on the power ON SW.
(When the temperature falls below 120°C
in the standby mode.)
Thermistor defect
Heater lamp failure
Thermostat failure
Control PWB failure
Check the heater lamp blinking with SIM 52.
When the lamp blinks normally:
Check the thermistor and the harness.
Check the MCU PWB thermistor input
circuit.
When the lamp does not light:
Check for disconnection of the heater
lamp and thermostat.
Check the interlock switch.
Check the power PWB and the MCU PWB
lamp control circuit.
Clear the display of self-diagnostics with
SIM 14.
5 continuous T10D(T20D) not-reaching
JAM
T10D(T20D) not-reaching JAM was
detected 5 continuous times.
The fusing JAM is not completely
removed. (Jam paper remains.)
T10D or T20D sensor breakdown or
harness connection trouble
Fusing unit installation failure
Check for jam paper in the fusing section.
(paper winding, etc.)
Check fusing unit installation
Clear the trouble with SIM 14.
Fusing thermistor abnormality detect
Fusing thermistor temperature transient
abnormality (Paper winding)
Paper wound around the fusing roller.
Fusing pawl abnormality
Fusing unit installation failure
Check for jam paper in the fusing section.
(paper winding, etc.)
Check installation of the fusing unit. Check
the fusing pawl.
Clear the trouble with SIM 14.
Trouble
code
Main Sub
code code
L1
00
Details of trouble
Content
Details
Cause
Check
and
remedy
L3
00
Content
Details
Cause
Check
and
remedy
L4
01
Content
Details
Cause
Check
and
remedy
Scanner feed trouble
Scanner feed is not completed within the
specified time.
Mirror unit defect
Scanner wire disconnection
Origin detection sensor error
Mirror motor harness abnormality
Check the scanning operation with SIM 11.
Mirror base feed trouble
Check for disconnection of the scanner
wire.
Check the harness and connector
between the mirror motor and the MCU
PWB.
Replace the mirror unit.
Replace the MCU PWB.
When the mirror feeds:
Check the mirror home position sensor
with SiM 1-2.
Scanner return trouble
Scanner return is not completed within the
specified time.
"When OC copying with the mirror at the
home position, the mirror is not in the
home position. "
Mirror unit defect
The scanner wire is disconnected.
Origin detection sensor error
Mirror motor harness abnormality
Check the scanning operation with SIM 11.
Mirror base return trouble
Check for disconnection of the scanner
wire.
Check the harness and connector
between the mirror motor and the MCU
PWB.
Replace the mirror unit.
Replace the MCU PWB.
When the mirror feeds:
Check the mirror home position sensor
with SiM 1-2.
Main motor lock
The main motor does not rotate.
The motor lock signal is detected for 1sec
or more after the main motor rotates.
The motor lock signal is detected for 1sec
during rotation of the main motor.
Main motor defect
Main motor connection harness trouble or
disconnection
MCU PWB failure
Check the main motor operation with SIM
25-1.
Check connection of the main motor
harness and connector.
Replace the main motor.
Replace the MCU PWB.
Trouble
code
Main Sub
code code
L4
11
Details of trouble
Content
Details
Cause
Check
and
remedy
L6
10
Content
Details
Cause
Check
and
remedy
L8
01
Content
Details
Cause
Check
and
remedy
U2
04
11
Content
Details
Cause
Check
and
remedy
Remarks
Content
Details
Cause
12
Check
and
remedy
Remarks
Content
Details
Cause
Check
and
remedy
Remarks
AR-235/275 TROUBLE CODE LIST - 7
Shifter motor trouble
The shifter home position detection signal
is not detected when the shifter is
operating.
Shifter motor trouble or harness
connection trouble and disconnection
Shifter home position sensor trouble
Check the shift motor operation with SIM
3-11.
Check connection of the shifter motor
harness/connector.
Replace the shifter motor.
Replace the MCU PWB.
Polygon motor lock trouble
The polygon motor does not rotate.
The motor lock signal is detected for 6sec
or more after the polygon motor rotates.
The motor lock signal is detected for 1sec
during rotation of the polygon motor.
Polygon motor unit failure
Polygon motor connection harness trouble
or disconnection
MCU PWB failure
Check the polygon motor operation with
SIM 61-1.
Check connector/harness of polygon
motor
Replace the polygon motor.
Replace the MCU PWB.
Zero cross detection error
The zero cross signal is not detected.
Power failure
MCU PWB abnormality
Check connection of the harness and
connector.
Replace the MCU PWB.
Power unit replacement
EEPROM communication error
MCU PWB EEPROM access circuit failure
EEPROM defective
ICU PWB EEPROM access circuit failure
Check that the EEPROM is properly set.
Clear trouble with SIM 16.
Replace the MCU PWB.
EEPROM abnormality
Counter check sum error
Counter check sum value stored in the
EEPROM is abnormal.
EEPROM defective
ICU PWB EEPROM access circuit failure
Check that the EEPROM is properly set.
Clear trouble with SIM 16.
Replace the MCU PWB.
Checksum error in counter data area
Adjustment value check sum error
Adjustment value check sum error
(EEPROM)
EEPROM defective
ICU PWB EEPROM access circuit failure
Check that the EEPROM is properly set.
Clear trouble with SIM 16.
Replace the MCU PWB.
Checksum error in adjustment value data
area
Trouble
code
Main Sub
code code
20
U2
Details of trouble
Content
Details
Cause
Check
and
remedy
Remarks
40
Content
Details
Cause
Check
and
remedy
U7
00
Remarks
Content
Details
Cause
U9
00
Check
and
remedy
Content
Details
Cause
Check
and
remedy
80
Content
Details
Cause
Check
and
remedy
Machine speed code data error
The machine information is not identical to
the model code speed information.
EEPROM defective
SIM operation error
Check that the machine set with SIM 2657 is identical to the model information.
When the boot program speed code does
not match with the body model
information.
CRUM chip communication error
Error in MCU-CRUM chip communication
CRUM chip failure
Developing unit contact trouble
MCU PWB failure
Replace the CRUM chip.
Check installation of the developing unit.
Clear the trouble with SIM 16.
Replace the MCU PWB.
CRUM communication error
RIC communication trouble
Error in communication with RIC
Error in communication test after turning
on the power or canceling SIM.
Connector harness contact trouble or
disconnection
RIC control PWB trouble
MCU PWB failure
Malfunction by noises
check the communication cable
connectors from the RIC box to the main
body.
U9-**: MCU-OPE communication trouble
Communication establishment error/
framing/parity/protocol error
Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure
Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.
Check ROM on the operation control
PWB.
Operation control PWB communication
trouble (Protocol)
Communication trouble between MCU and
the operation control PWB (Protocol error)
Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure
Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.
Trouble
code
Main Sub
code code
81
U9
Details of trouble
Content
Details
Cause
82
Check
and
remedy
Content
Details
Cause
84
Check
and
remedy
Content
Details
Cause
88
Check
and
remedy
Content
Details
Cause
99
Check
and
remedy
Content
Details
Cause
CE
00
Check
and
remedy
Content
Detail
Cause
Check
and
remedy
AR-235/275 TROUBLE CODE LIST - 8
Operation control PWB communication
trouble (Parity)
Communication trouble between MCU and
the operation control PWB (Parity error)
Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure
Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.
Operation control PWB communication
trouble (Overrun)
Communication trouble between MCU and
the operation control PWB (Overrun error)
Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure
Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.
Operation control PWB communication
trouble (Framing)
Communication trouble between MCU and
the operation control PWB (Framing error)
Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure
Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.
Operation control PWB communication
trouble (Time-out)
Communication trouble between MCU and
the operation PWB (Time-out error)
Operation control PWB connector
disconnection
Operation control PWB MCU PWB
harness failure
Check the connectors and harness of the
operation control PWB and MCU PWB.
Check the grounding of the copier.
Operation panel destination error
An error occurred in checking the
operation panel and the destination of the
body.
Erroneous connection the operation panel
unit
SIM setup error
Check the destination information of the
operation panel unit and the MCU. (Use
SIM 26-22 for the destination of the body.)
The other communication error has
occurred.
Communication error
Network Cable connection failure
1) Check that the Network Cable is
properly inserted.
Trouble
code
Main Sub
code code
CE
01
Details of trouble
Content
Detail
Cause
Check
and
remedy
02
Content
Detail
Cause
Check
and
remedy
The print server card (AR-NC3D) is not
installed or defective.
NC3D connection failure
NC-3D is not installed to the AR-PB2A
board.
NC-3D control PWB trouble
1) Check that the NC-3D is installed to
the AR-PB2A board.
Trouble
code
Main Sub
code code
CE
05
Cause
Check
and
remedy
EE
EL
Cause
3) Check from the Web Page that the
Primary/Secondary E-mail Server
Address or the Destination FTP server/
Desktop PC address are properly set.
EU
Content
Detail
Cause
Check
and
remedy
04
Content
Detail
Cause
Check
and
remedy
2) Check that the SMTP server/FTP
server/NST causes a trouble or not.
The entered account name of the FTP
server or the password is invalid.
The entered account name of the FTP
server or the password is invalid.
Network Cable connection failure
The account name of the FTP server
recorded as the destination or the
password for the account name is
erroneous.
1) Check that the Network Cable is
inserted properly.
Check
and
remedy
Content
Details
4) If the above address is described with
Hostname, check that the DNS server
is properly set.
03
Content
Details
2) Check that the connected network
supports TCP/IP protocol.
5) Check that the SMTP server/FTP
server/NST causes a trouble or not.
The specified server does not correspond
during image transmission.
The specified server does not correspond
during image transmission.
Network Cable connection failure
SMTP server/FTP server/NST trouble
1) Check that the Network Cable is
inserted properly.
Content
Detail
2) Output the NIC Config. Page to check
the NIC version.
3) Replace the NIC.
The specified mail server or the FTP
server is not found.
The specified mail server or the FTP
server is not found.
Network Cable connection failure
Network setup failure
SMTP server/FTP server/NST trouble
1) Check that the Network Cable is
inserted properly.
Details of trouble
Cause
PF
00
Check
and
remedy
Content
Details
Cause
Check
and
remedy
2) Check that the account name of the
FTP server recorded as the destination
and the password for the account
name are proper.
AR-235/275 TROUBLE CODE LIST - 9
The entered directory of the FTP server is
invalid.
The entered directory of the FTP server is
invalid.
Network Cable connection failure
Check that the directory name exists in the
FTP server recorded as the destination.
1) Check that the Network Cable is
inserted properly.
2) Check that the directory name exists in
the FTP server recorded as the
destination.
Developer adjustment trouble (Over-toner
abnormality)
An abnormality occurred in execution of
automatic developer adjustment.
Sample data over-toner was detected.
Toner concentration sensor abnormality
Toner concentration trouble
Developing unit trouble
MCU PWB failure
Use SIM 25-2 to perform the auto
developer adjustment.
Developer adjustment trouble (Undertoner abnormality)
An abnormality occurred in execution of
automatic developer adjustment.
Sample data under-toner was detected.
Toner concentration sensor abnormality
Toner concentration trouble
Developing unit trouble
MCU PWB failure
Use SIM 25-2 to perform the auto
developer adjustment.
RIC copy inhibit signal received
The copy inhibit command from RIC is
received.
Judged by the host.
Information the host.
[10] DISASSEMBLY, ASSEMBLY AND MAINTENANCE
1. Maintenance table
N: Check (Check, clean, replace or adjust according to necessity.)
Y: Cleaning
R: Replace
L: Lubricate
Unit
Parts
Process unit Drum
Cleaning blade
Drum frame unit
Seal F/R
MC unit
50k
R
R
N
N
100k
R
R
N
N
150k
R
R
N
N
200k
R
R
R
N
250k
R
R
N
N
300k
R
R
N
N
R
R
R
R
R
R
N
R
N
R
N
R
Developer
DV seal
Side seal (F/R)
Upper heat roller
Lower heat roller
Upper separation pawl
Lower separation pawl
Thermistor
Upper heat roller gear
Upper heat roller bush
Lower heat roller bearing
Paper guide
Pickup roller (Multi bypass tray)
Separation sheet (Multi bypass tray)
Separation roller (Multi bypass tray)
Pickup roller (500 sheets tray)
Separation sheet (500 sheets tray)
Separation roller (500 sheets tray)
Transport roller unit
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
R
Y
R
Y
Y
R
R
N
Y
N
N
N
N
N
N
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
Y
Y
Y
Y
Y
L
N
N
Y
N
N
N
N
N
N
R
N
N
R
R
R
R
Y
R
R
R
Y
N
N
N
N
N
N
Y
R
Y
R
Y
R
Ozone filter
Paper feed rollers
Gears
Dust-proof glass
R
Y
L
R
Y
L
R
Y
L
R
Y
L
R
Y
L
R
Y
L
N
N
N
N
N
N
Separation pawl unit
DV unit
Fusing unit
Paper feed
Transport
roller unit
Ozone filter
Others
LSU
2. Counter clear
Item
Maintenance cycle setting
Jam/trouble counter clear
Paper feed counter clear
DF/Scan/Stapler counter clear
Maintenance counter clear
Developing counter clear
Copy counter clear
Drum counter clear
Printer, other counter clear
FAX related counter clear
Scanner mode counter clear
SIM
SIM 21-1
SIM 24-1
SIM 24-2
SIM 24-3
SIM 24-4
SIM 24-5
SIM 24-6
SIM 24-7
SIM 24-9
SIM 24-14
SIM 24-15
Remarks
At maintenance
At maintenance
At drum replacement
At developer replacement
At drum replacement
3. List of disassembly and assembly
Unit
A. Process unit
Parts
(1) Drum
(2) Drum section a.
b.
c.
d.
e.
Main charger
Cleaning blade
Drum frame unit
Moquette F/R
Separation pawl
Note
Unit supply only
(Individual parts in the unit can not be supplied.)
Unit supply only
(Individual parts in the unit can not be supplied.)
Changing criteria for parts: 50k
Changing criteria for parts: 50k
Changing criteria for parts: 50k
Changing criteria for parts: 50k
Changing criteria for parts: 50k
Changing criteria for parts: 50k
Unit supply only
(Individual parts in the unit can not be supplied.)
Clean only the outer surface of the glass with the
developing CRU disassembled (with the LSU
attached to the machine).
Unit
B. Developing unit
Parts
(1) Developer
(2) DV seal/side seal
C. Fusing unit
(1) Upper heat roller
(2) Lower heat roller
(3) Fusing Separation Pawl (upper)
(4) Fusing Separation Pawl (lower)
(5) Thermistor
(6) Upper heat roller gear
(7) Upper heat roller bearing
(8) Lower heat roller bearing
(9) Paper guide
D. Paper feed
(1) Multi manual a. Paper feed roller/pickup
paper feed
roller
b. Separation sheet
(2) Upper 500
a. Paper feed roller
sheets tray
b. Pickup roller
paper feed
c. Separation sheet
(3) Lower 500
a. Paper feed roller
sheets tray
b. Pickup roller
paper feed
c. Separation sheet
E. Side door unit
(1) Transport roller unit
F. 1st paper exit unit (1) Paper exit roller
G. Laser unit
(1) LSU
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 1
Unit
H. Power unit
I. PWB
b. Cleaning blade
Parts
(1) Power source
(1) Option CN PWB
(2) IMC PWB
(3) MCU PWB
(4) Motherboard PWB
(5) Second interface PWB
Ozone filter
J.Others
1)
1
2)
4. Details
A. Process unit
(1) Drum
1)
2)
c. Drum frame unit
2
4)
3)
1
No.
Part name
1 Drum
Service items
Replace
Cycle
50k
Remarks
(2) Drum section
a. Main charger
1)
4)
1)
d. Moquette F/R
2)
4
3
3)
Note: If it disturbs the blade movement, replace it and attach new one.
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 2
e. Separation pawl
Disassembly * Hold the tip of the separation pawl and remove it.
Assembly* Press the center of the separation pawl and install it.
5
1
No.
1
2
3
4
Part name
Cleaning
blade
Drum frame
unit
Service
items
Replace
Check
Replace
Moquette F/R Check
MC unit
Replace
Cycle
Separation
pawl unit
Check
Replace
∗
50k
50k
200k
50k
50k
5
Remarks
50k
100k
∗ When assembling, check that the hook is securely engaged in two
positions.
Unit supply only
(Individual parts in the unit
can not be supplied.)
Unit supply only
(Individual parts in the unit
can not be supplied.)
(2) DV seal/side seal
B. Developing section
(1) Developer
2)
3
1)
No.
Part name
1 Developer
2 DV seal
3 DV side seal (F/R)
2
Service items
Replace
Check
Check
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 3
3
Cycle
50k
50k
50k
Remarks
C. Fusing section
1)
2)
4)
3)
1)
2)
2)
1)
1)
(1) Upper heat roller
1)
4)
3)
2)
2)
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 4
(4) Fusing Separation Pawl (lower)
1
4
2)
1)
(2) Lower heat roller
1)
4
4)
2
4)
3)
2)
3)
2)
2)
(5) Thermistor
2) 3)
1)
4)
2) 3)
2)
5
1)
(3) Fusing Separation Pawl (upper)
3
3
3
3
1)
1)
(6) Upper heat roller gear
2)
1)
2)
2)
2)
1)
2)
3)
1)
3)
3)
3)
6
(7) Upper heat roller bearing
1)
2)
7
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 5
1)
7
(8) Lower heat roller bearing
D. Paper feed section
8
A
5)
B
4)
3)
2)
3)
2)
2)
C
5)
3)
2)
3)
A
B
C
8
Paper feed roller
Pickup roller
Separation sheet
(1) Multi manual paper feed
1)
a. Paper feed roller/pickup roller
1)
1)
(9) Paper guide
4)
3)
2)
9
7)
6)
5)
2)
1)
No.
Part name
1 Upper heat roller
2
3
4
5
6
7
8
9
Service items
Cleaning
Replace
Lower heat roller
Cleaning
Replace
Upper separation pawl Cleaning
Replace
Lower separation pawl Cleaning
Replace
Thermistor
Cleaning
Upper heat roller gear Lubricate
Replace
Upper heat roller
Check
bearing
Replace
Lower heat roller
Check
bearing
Replace
Paper guide
Cleaning
Cycle
50k
150k
50k
300k
50k
150k
50k
300k
50k
50k
150k
50k
150k
50k
300k
50k
Remarks
7)
Removal*Raise the shutter arm before its removal.
2)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 6
1)
2)
Installation*Install so that the boss of the lever arm comes into the rib
of the shutter arm.
3)
1)
2)
5)
1)
L O CK
4)
T
2)
1
OK
2
b. Separation sheet
1)
2)
3
3)
Installation*Install so that the cam transmit arm (1) comes under the
roller arm (2).
1)
2)
∗ Slightly apply grease GP501MR (UKOG-0012QSZZ) around the
axis. One rice grain for each.
No.
1
2
3
Part name
Service
items
Check
Pickup roller (Multi
bypass tray)
Separation roller (Multi Check
bypass tray)
Separation sheet (Multi Check
bypass tray)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 7
Cycle
50k
50k
50k
Remarks
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
(2) Upper 500 sheets tray paper feed
1)
a. Paper feed roller/pickup roller
2)
2)
1)
∗ When replacing, be careful not
3)
to adhere conduction grease
(black) to the drive section.
Slightly apply grease GE676
(UKOG-0013QSZZ) to the
drum boss.
1
4)
2)
3)
4)
2
1)
Note: With the toner cartridge installed, do not tilt or shake the developer cartridge.
2)
b. Separation sheet
2)
1)
1)
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 8
3
∗ Slightly apply grease GP501MR (UKOG-0012QSZZ) around the
axis. One rice grain for each.
Grease should not come out when assembling.
No.
1
3)
2
1)
3
Part name
Service
items
Check
Cycle
Pickup roller (500
sheets tray)
Separation roller (500 Check
sheets tray)
Separation sheet (500 Check
sheets tray)
50k
50k
50k
Remarks
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
Changing criteria
for parts: 50k
(3) Lower 500 sheets tray paper feed
a. Paper feed roller/pickup roller
1)
3)
2)
1)
1)
2)
3)
2)
1
4)
2)
2
4)
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 9
∗ Check that two springs are securely inserted into the transfer roller
b. Separation sheet
unit bosses.
No.
1
Part name
Transport
roller unit
Service
items
Cleaning
Replace
Cycle
Remarks
50k
Unit supply only
(Individual parts in the
unit can not be supplied.)
100k
F. 1st paper exit unit
(1) Paper exit roller
2)
1)
3
2)
1)
∗ Slightly apply grease GP501MR (UKOG-0012QSZZ) around the
axis. One rice grain for each.
Grease should not come out when assembling.
No.
1
2
3
Service
items
Check
Part name
Pickup roller (500
sheets tray)
Separation roller (500 Check
sheets tray)
Separation sheet (500 Check
sheets tray)
Cycle
Remarks
50k
Changing criteria for
parts: 100k
Changing criteria for
parts: 100k
Changing criteria for
parts: 100k
50k
50k
E. Side door unit
(1) Transport roller unit
3)
1
2)
2)
1)
1)
3)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 10
1)
• Remove the delivery frame.
2)
1)
1)
2)
2)
1)
1)
•
front right cabinet
1)
2)
3)
2)
1)
• Remove the MCU PWB section connector.
1)
2)
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 11
(1) LSU
Note: Check to confirm that the solenoid shaft is in the gate bracket,
and fix with the screw.
2)
1)
1)
1)
1)
1)
1)
2)
2)
1)
G. Laser unit
1)
3)
4)
Remove the panel unit, before performing the following works.
2)
Note: Before removing the left cover, remove the No.1 cassette in
advance.
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 12
I. PWB
(1) Option CN PWB
1)
2)
2)
2)
2)
2)
3)
1)
3)
1)
(2) IMC PWB
1)
H. Power unit
(1) Power source
(3) MCU PWB
2)
1)
1)
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 13
(4) Motherboard PWB
2)
1)
1)
1)
1)
2)
2)
1)
1)
1)
1)
4)
2)
3)
2)
1)
1)
1)
2)
1)
1)
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 14
(5) Second interface PWB
1)
1
2)
1)
Note: Before removing the left cover, remove the No.1 cassette in
advance.
2)
2)
1)
1)
1)
1)
J. Ozone filter
1
2)
1)
1)
No.
Part name
1 Ozone filter
Service items
Replace
AR-235/275 DISASSEMBLY, ASSEMBLY AND MAINTENANCE - 15
Cycle
50k
Remarks
[11] OTHERS
A. Program download procedure (Main body
program, FAX program)
1. Flash ROM version up procedure
The download procedures of the main body program and the FAX program are as follows:
(Items necessary for upgrade)
A
Personal computer
1) Preliminary procedure: Connect the PC and the main body with
the download cable (RS-232C cable).
B
RS232C Cross cable (D-sub 9pin to D-sub 9pin, or D-sub 25pin to
D-sub 9pin)
2) Main body side: Turn on the power of the main body. The machine
enters the download mode.
C
Software for upgrade
3) PC side: Confirm that the tree is displayed on the maintenance
program.
(Type of ROM)
∗ Be sure to perform procedure 2) before turning on the power.
Flash ROM is directly attached to each PWB
(Targeted PWBs)
1
MCU-PWB
2
Panel-PWB
3
IMC-PWB
4
FAX-PWB
5
Finisher-PWB
Diagrammatic sketch for upgrade method
(Personal computer)
A
RS232C connector
(9pin or 25pin)
B
When the tree is displayed, download may be performed. (Double
click to use.)
C
RS232C Cross cable
(D-sub 9pin to D-sub 9pin)
or
(D-sub 25pin to D-sub 9pin)
Download
data
4) PC side: Double click "Special" in the main tree item to develop
the sub tree items, and double click "All Area Download" in the sub
tree items.
I/F Circuit (9pin)
1
5) PC side: The maintenance program asks you the file name. Specify the download file (*.dat).
MCU-PWB
Download file
• leopXXXX.dat:
Collective download file (Main body, IMC, Panel, FAX, Finisher)
XXXXT: Whole release version
Operation
panel
2
IMC-PWB FAX-PWB
3
4
Finisher
6) PC side: The download file is specified, download is automatically
performed.
The download time is as follows
5
• Main body program download time: About 5 min
• FAX program download time:
About 5 min
(AR-235/275)
Note: If the download file version is older than the machine file version,
the following alert message is displayed during download.
(Necessary files for download)
• Maintenance software: mainte.exe
• Loader files
Main body loader file: downbios.cvt
Panel loader file: pnlbios.cvt
IMC loader file: imcbios.cvt
FAX loader file: faxbios.cvt
Finisher loader file: fiubios.cvt
• Printer control board data transfer tool: fcopy.exe
The maintenance program performs the following program download
operations:
• Main body program download
• FAX program download
• Printer control board program download
In this case, press the OK button to interrupt the current download operation, and the next download is performed.
7) PC side: When the message below is displayed, download is
completed.
Completion message: DOWNLOAD COMPLETE
8) After-process: Terminate the maintenance program, and turn on
the power of the main body.
With the above procedures, download is completed.
AR-235/275 OTHERS - 1
2. User programs
User Program
Auditing Mode
Copies per Account
Reset Account
Account Number
Control
Account Limit
Description
Enables or disables the basic auditing mode, which controls
access to copier.
Displays the total number of copies made against account
numbers.
Resets all audit accounts or selectively resets individual
accounts.
Registers accounts, deletes accounts or changes an account
number.
Sets the maximum number of copies which can be made
against a registered account number.
Guards against trial and error entering of audit account
numbers.
Changes the key operator code number.
Default
Account Number
Security
Key Operator Number
Change
Exposure Adjust
Limit of Copies
Margin Default
Lightens or darkens copies in the automatic exposure mode.
Sets the maximum number of copies that can be selected.
Sets the initial margin shift values.
Erase Adjust
Set the initial amount of the erase area.
Initial Conditions
Stream Feeding
Message Time
Sets the copier's initial settings in the ready condition.
Enables the stream feeding mode for copying from the optional
document feeder.
Enables/disables rotation of original images.
Sets the default output mode.
Sets the output trays for the copy and printer modes.
Sets the memory assignment used for printer feature (optional
for AR-235 and AR-275).
Enables/disables the offset function in the output tray.
Reduces toner consumption.
Sets a time interval after which the copier enters the auto power
shut-off mode.
Sets a time interval after which the copier returns to the initial
settings.
Sets the time that elapses before the copier enters the preheat
mode after copying is completed.
Sets the length of time that messages are displayed.
Time Out Setting
Sets the time after which a print job resumes.
30sec
Disable Auto Paper
Selection
Disable Auto Tray
Switching
Disable Job Program
Changing
Disable SPF/RSPF
Prevents automatic paper selection.
Rotation Copy
Sort Auto Select
Output Trays
Memory for Printer
Offset Function
Toner Save Mode
Auto Power Off
Auto Clear
Preheat Mode
Disable Duplex Copy
Disable Stapler
Disable Center Tray
Counting
Disable PC/Modem
Disable Auto Power
Shut-off
Disable Beep at Key
Touch
Disable Backlight
Change
Total Count
Prevents automatic switching between the paper trays.
Prevents stored programs from being replaced or deleted.
Prevents the use of the optional document feeder when it
malfunctions.
Temporarily prevents the duplex system from operating when it
malfunctions. Allows the use of the copier but not the duplex
system.
Prevents damage to the stapler while awaiting repair service.
(The stapler is included in the optional finisher (AR-FN5).)
Disables count of paper output tray of the copier.
Provides or prevents access to key operator programs through
a PC/modem without key operator code entry.
Disables the auto power shut-off mode.
Enables or disables sounding of beep when keys are touched.
Disables change of LCD backlighting color.
Recalls the total counts, including counts of the copier,
document feeder, duplex module, and stapler.
AR-235/275 OTHERS - 2
Setting range
00000 (5 digits)
Level 3
999
5 steps
AB series: 5mm pitch (5 to 20mm),
Inch series: 1/4" pitch (1/4 to 1“)
AB series: 5mm pitch (5 to 20mm),
Inch series: 1/4" pitch (1/4 to 1")
50%
30 to 70% (in the increment of 10%)
60sec
10/30/60/90/120/240min
60sec
0/30/60/90/120/240sec
15min
0/1/2/5/10/15/30min
Normal (6sec)
Slow (9sec)/Normal (6sec)/Slow
(3sec)
0sec (Immediate)/10sec/30sec/
60sec
3. E-MAIL STATUS/E-MAIL ALERTS
A. Basic functions
C. Printer controller specifications
1) Event driven type text message transmission by using MIB information of Printer control board.
The controller supports the following transmission functions:
2) Management information which body has is coded and transmitted
in a file type according to the schedule or in the event driven type.
In this case, the specified mail software is used to receive and
develop the data.
The above functions are available as standard provision only when the
Printer control board and the NIC card are installed.
For 2), the software key protect is made.
B. Main body specifications
The body provides event information to the controller. The file generated by the MCU according to setup can be transmitted as an attached
file as information for dealers. When a dealer's mail address is set, a
file can be attached only to a mail which is transmitted to the mail
address.
To read the attached file, the specified mail software is required. That
is, the attached file includes numeral information of each main body
and event information in coded state. If the other mail software is used
to receive, the display contents on the client side cannot be guaranteed.
• Text mail transmission by event driven setup and schedule driven
setup.
• Mail transmission with an attached file by event driven setup and
schedule driven setup. For the attached file, the printer controller
makes a file of information data from the MCU.
• It controls sending time and requests for the machine information at
the sending time to the MCU.
(1) Additional machine information
Information to identify the machine. The user administrator manually
enters this information by using a browser. The information is displayed
in the text of the mail.
∗ These items of information are kept on the controller side or on the
NIC side.
• Machine name
• Machine code
• Installation place
(2) Alert Message
ID
1
Event
Paper Jam
2
Toner Low
3
Toner Empty
4
Paper Empty
5
Service Required
6
PM Required
Message
Condition
! ! ! MISFEED HAS OCCURRED ! ! ! When paper/document jam has occurred. If a jam is detected when the power is
turned ON or reset, checking is made again.
! ! ! TONER SUPPLY IS LOW ! ! !
When toner LOW is detected for the first time. If toner LOW is detected when the
power is turned ON or reset, checking is made again.
! ! ! ADD TONER ! ! !
When toner empty is detected for the first time. If toner empty is detected when
the power is turned ON or reset, checking is made again.
! ! ! LOAD PAPER/XXX ! ! !
When paper empty is detected for the first time. If paper empty is detected when
the power is turned ON or reset, checking is made again. No information on the
number of steps of trays. Manual feed is not supported. When a tray empty is
detected, information of all the trays that are empty at that time is delivered.
! ! ! CALL FOR SERVICE ! ! !
When the machine enters the self-diagnosis mode. If detected when the power is
turned ON or reset, checking is made again.
! ! ! MAINTENANCE REQUIRED ! ! ! When the maintenance counter or the developer counter reaches the specified
count. If detected when the power is turned ON or reset, checking is made again.
(3) Status Message
• When the controller sends two or more requests during a job, only
the last request is accepted.
Counter information
When schedule driven is set, the total counter, the copy counter, and
the printer counter are displayed in a mail address for general. These
information items are supplied from the controller MIB. The "total
counter" means the "effective paper counter" controlled by the MCU.
Timer information
For schedule drive message, the Printer controller controls transmission time by means, and transmits a mail.
Timer setup is made from the Web setup page.
D. Handling of transmission data
In E-mail Alerts and E-mail Status, a transmission task is generated
regardless of the job which is under process in the machine. These
tasks are processed in the following rules:
• When the machine receives a mail transmission request during a job
process (copy scan, copy output, print output, other process) of the
machine, it performs transmission process regardless of the job.
• When the machine receives a mail transmission request under other
situation, if the job is triggered during transmission process, the job
is started.
• When the machine receives a mail transmission request during the
simulation mode, the request is accepted and transmission process
is started.
• When the machine receives a mail transmission request during the
key operator program, it is accepted and transmission process is
started.
AR-235/275 OTHERS - 3
CAUTION FOR BATTERY REPLACEMENT
(Danish)
ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
“BATTERY DISPOSAL”
CONTAINS MANGANESE DIOXIDE LITHIUM BATTERY
MUST BE DISPOSED OF PROPERLY.
REMOVE THE BATTERY FROM THE PRODUCT AND
CONTACT FEDERAL OR STATE ENVIRONMENTAL
AGENCIES FOR INFORMATION ON RECYCLING
AND DISPOSAL OPTIONS.
“BATTERY DISPOSAL”
CONTAINS LITHIUM-ION BATTERY.
MUST BE DISPOSED OF PROPERLY.
REMOVE THE BATTERY FROM THE PRODUCT AND
CONTACT FEDERAL OR STATE ENVIRONMENTAL
AGENCIES FOR INFORMATION ON RECYCLING
AND DISPOSAL OPTIONS.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
All rights reserved.
Printed.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.
Trademark Acknowledgments
Microsoft Windows, MS-DOS, Windows NT, Windows 2000 are trademarks of Microsoft
Corporation in the U. S. A. and other countries.
Macintosh, Power Macintosh, Mac OS, LaserWriter, and AppleTalk are registered trademarks of
Apple Computer, Inc.
IBM, PC/ AT, and PowerPC are trademarks of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation.
PCL is a trademark of the Hewlett- Packard Company.
PostScript is a registered trademark of Adobe Systems Incorporated.
NetWare is a registered trademark of Novell, Inc.
All other trademarks and copyrights are the property of their respective owners.
Digital Document Systems Group
Quality & Reliability Control Center
Yamatokoriyama, Nara 639-1186, Japan
2001 April Printed