Epson EB-G6650WU Guide User`s guide

User's Guide

Notations Used in This Guide

• Safety indications

The documentation and the projector use graphical symbols to show how to use the projector safely.

Please understand and respect these caution symbols in order to avoid injury to persons or property.

Warning

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

Caution

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

• General information indications

Attention a s

g

[Name]

Menu Name

Indicates procedures which may result in damage or injury if sufficient care is not taken.

Indicates additional information and points which may be useful to know regarding a topic.

Indicates a page where detailed information regarding a topic can be found.

Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendix".

s

"Glossary" p.176

Indicates the name of the buttons on the remote control or the control panel.

Example: [Esc] button

Indicates Configuration menu items.

Example:

Select Brightness from Image.

Image - Brightness

Contents

3

Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2

Introduction

Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Removing and Attaching the Projector Lens Unit . . . . . . . . . . . . . . . . . . . . . . . . 16

Attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Preparing the Projector

Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Changing the direction of the image (projection mode) . . . . . . . . . . . . . . . . . 21

Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Adjusting the position of the image on the projected screen . . . . . . . . . . . . . . 23

Displaying a Test Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Adjusting the Position of the Projected Image (Lens Shift) . . . . . . . . . . . . . . . . . . 24

Adjusting the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Correcting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

When using the short throw zoom lens ELPLU01 . . . . . . . . . . . . . . . . . . . . . . 26

Adjusting the Image Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Adjusting the Horizontal Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

ID Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Set the projector ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Checking the Projector ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setting the remote control ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setting the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Connecting a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Connecting Image Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Connecting External Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Connecting a LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Connecting an HDBaseT Transmitter (EB-G6750WU Only) . . . . . . . . . . . . . . . . . . 36

Installing the Wireless LAN Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Attaching the Cable Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Basic Usage

Projecting Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Automatically Detect Input Signals and Change the Projected Image (Source Search)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Switching to the Target Image by Remote Control . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Correcting Distortion in the Projected Image . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

H/V-Keystone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Quick Corner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Arc Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . . . . . . 46

Projecting 3D images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . . . . . . 47

Changing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Hue, Saturation, and Brightness Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 49

Gamma Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Frame Interpolation (EB-G6750WU/EB-G6650WU/EB-G6550WU/EB-G6450WU only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Contents

4

Useful Functions

Multi-Projection Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Adjusting the Position of the Projected Image . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Point Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Checking the Color Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Adjust the Edges of the Images (Edge Blending) . . . . . . . . . . . . . . . . . . . . . . . . . 55

Adjusting the brightness of the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Performing edge blending . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Adjusting to Match Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Scaling an Image (Scale) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Projecting Two Images Simultaneously (Split Screen) . . . . . . . . . . . . . . . . . . . . . 60

Operating procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Restrictions during split screen projection . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . . . . . . . . . 63

Freezing the Image (Freeze) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Enlarging Part of the Image (E-Zoom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Saving a User's Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Memory Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Saving/Loading/Erasing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Scheduling Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Saving a Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Setting Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Editing a schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Managing Users (Password Protection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Kinds of Password Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Setting Password Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Restricting Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Control Panel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Remote control button lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Anti-Theft Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Installing the wire lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Configuration Menu

Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Configuration Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Extended Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Network Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Soft keyboard operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Basic menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Wireless LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Wired LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Administrator Settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Info Menu (Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Reset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Troubleshooting

Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

When the Indicators Provide No Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Problems Relating to Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

No images appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Moving images are not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Projection stops automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Contents

5

The message Not supported is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

The message No Signal is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . . . 113

Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . . . 113

The image is truncated (large) or small, the aspect is not suitable, or the image has been reversed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Image colors are not right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Images appear dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Problems when Projection Starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Other Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . . . 117

The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Nothing appears on the external monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 119

I want to change the language for messages and menus . . . . . . . . . . . . . . . . 119

The authentication setting of wireless LAN fails . . . . . . . . . . . . . . . . . . . . . . 120

Email is not received even if a problem occurs in the projector . . . . . . . . . . . . 120

The battery that saves your clock settings is running low. is displayed . . . . . . . 120

Cannot change settings using a Web browser . . . . . . . . . . . . . . . . . . . . . . . 121

About Event ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Maintenance

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Cleaning the Projector's Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Cleaning the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Lamp replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

How to replace the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Resetting the lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Air filter replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

How to replace the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Notes on Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Moving Nearby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

When Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Preparing packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Notes when packing and transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Image Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Panel Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Color Uniformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Adjusting the Lens Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Appendix

Network Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Projecting with "Connect to a Network Projector" . . . . . . . . . . . . . . . . . . . . . . . 142

Making a WPS (Wi-Fi Protected Setup) Connection with a Wireless LAN Access Point

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Connection Setup Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Using the Quick Wireless Connection USB Key . . . . . . . . . . . . . . . . . . . . . . . . . 143

Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

About EasyMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

About Message Broadcasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Changing Settings Using a Web Browser (Web Control) . . . . . . . . . . . . . . . . . . . 145

Projector setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Displaying the Web Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Setting Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Secure HTTP Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

List of supported certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . . . . . . 148

Reading Error Notification Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Management Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Displaying the Web Remote Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

ESC/VP21 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

Command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

Contents

6

Cable layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

About PJLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

About Crestron RoomView

®

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

Operating a projector from your computer . . . . . . . . . . . . . . . . . . . . . . . . . 152

Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . 156

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 158

Projection Distance (For EB-G6750WU/EB-G6650WU/EB-G6550WU/EB-G6450WU/

EB-G6250W/EB-G6050W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

Standard zoom lens ELPLS06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

Short throw zoom lens ELPLU01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

Rear projection wide lens ELPLR03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

Middle throw zoom lens ELPLM04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160


Long throw zoom lens ELPLL06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

Projection Distance (For EB-G6350/EB-G6150) . . . . . . . . . . . . . . . . . . . . . . . . . 163

Standard zoom lens ELPLS06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

Short throw zoom lens ELPLU01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

Rear projection wide lens ELPLR03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165



Long throw zoom lens ELPLL06 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167

Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Component Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Composite video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

Input signal from the HDMI port and DisplayPort (EB-G6750WU/EB-G6650WU/EB-

G6550WU/EB-G6450WU/EB-G6250W/EB-G6050W) . . . . . . . . . . . . . . . . . . . . 170

Input signal from the HDMI port and DisplayPort (EB-G6350/EB-G6150) . . . . . . 170

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

Projector General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176

General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

Trademarks and Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

Introduction

This chapter explains the names for each part.

Part Names and Functions

The illustrations in this guide are for EB-G6750WU (with the standard zoom lens ELPLS06 attached).

Front/Top

Name

A Air exhaust vent

Function

Exhaust vent for air used to cool the projector internally.

Caution

While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent. Hot air from the air exhaust vent could cause burns, warping, or accidents to occur.

B

Name

Focus ring

Function

Adjusts the image focus.

s

"Correcting the Focus" p.26

C

D

Zoom ring

Lens unit removal button

Adjusts the image size.

s

"Adjusting the Image Size" p.26

When replacing the lens unit, press this button and then remove the lens unit.

s

"Removing and Attaching the Projector Lens Unit" p.16

Receives signals from the remote control.

E Remote receiver

F Status indicators The color of the indicators and whether they are flashing or lit indicate the status of the projector.

s

"Reading the Indicators" p.106

G Wireless LAN indicator Indicates the access status of the supplied or optional wireless LAN unit.

s

"Optional Accessories" p.156

H Air intake vent

(air filter)

Takes in air to cool the projector internally.

s

"Cleaning the Air Filter" p.125

I Speaker Outputs audio.

J Air filter cover operation knob

Use this knob to open the air filter cover.

s

"Replacing the Air Filter" p.131

K Cable cover Cover for the rear interface cable connection section.

s

"Attaching the Cable Cover" p.39

L Vertical lens shift dial Turn the dial to move the position of the projected image up or down.

s

"Adjusting the Position of the Projected Image (Lens

Shift)" p.24

M Lens shift dial lock

N Horizontal lens shift dial

Locks or releases the lens shift dials.

Turn the dial to move the position of the projected image left or right.

s

"Adjusting the Position of the Projected Image (Lens

Shift)" p.24

8


Name

O Lamp cover

Function

Open when replacing the projector's lamp.

s

"Replacing the Lamp" p.128

Rear

Interface

Name

A Interface

B Security slot

C Power inlet

D Control panel

E Cable holder

Function s

"Interface" p.9

The security slot is compatible with the Microsaver

Security System manufactured by Kensington.

s

"Anti-Theft Lock" p.75

Connects to the power cable.

s

"Control Panel" p.11

Insert the supplied cable clamp here to prevent the HDMI cable from falling out.

s Quick Reference

Name

A Audio1 port

B Computer port

C

D

E

BNC port

Audio2 port

RS-232C port

F Remote port

G Audio-L/R port

H Video port

Function

Inputs audio from equipment connected to the Computer port.

For analog RGB signals from a computer and component video signals from other video sources.

For analog RGB signals from a computer and component video signals from other video sources.

Inputs audio from equipment connected to the BNC port.

When controlling the projector from a computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used.

s

"ESC/VP21 Commands" p.150

Connects the optional remote control cable set and inputs signals from the remote control. When the remote control cable is plugged into the Remote port, the remote receiver on the projector is disabled.

s


Inputs audio from equipment connected to the Video port or the S-Video port.

Inputs composite video signals from video sources.

9


10

Name

I S-Video port

J Audio Out port

K Monitor Out port

L DisplayPort

M HDMI port

N Audio3 port

O HDBaseT port (EB-

G6750WU only)

P LAN port

Q Service port

Function

For S-video signals from video sources.

Outputs audio from the currently projected image to an external speaker.

Outputs to an external monitor the analog signal from the computer connected to the Computer port or the BNC port. You cannot output signals input from other ports or component video signals.

Inputs video signals from DisplayPort compatible

computers. This projector is compatible with HDCP g

.

Inputs video signals from HDMI compatible video equipment and computers. This projector is compatible with HDCP

g .

Inputs audio from equipment connected to the

DisplayPort or the HDMI port.

Connects a LAN cable to the optional HDBaseT

Transmitter.

s

"Connecting an HDBaseT Transmitter (EB-

G6750WU Only)" p.36

s


Connects a LAN cable to connect to a network.

This port is used by maintenance personnel to control the projector. This should not normally be used.

Base

Name Function

A Front adjustable foot When setup on a surface such as a desk, extend the foot to adjust the position of the image.

s

"Adjusting the Image Position" p.27

B Rear feet When setup on a surface such as a desk, turn to extend and retract to adjust the horizontal tilt.

s

"Adjusting the Horizontal Tilt" p.27

C Screw holes to fix the cable cover

Screw holes to fix the cable cover in place.

s

"Attaching the Cable Cover" p.39


11

Name

D Security cable installation point

E Ceiling mount fixing points (four points)

F Screw hole for the screw to fix the lens unit removal button

Function

Pass a commercially available wire lock through here and lock it in place.

s

"Installing the wire lock" p.76

Attach the optional Ceiling Mount here when suspending the projector from a ceiling.

s

"Installing the Projector" p.20

s


When installing a lens unit, use this screw hole to fix the lens unit removal button using the screw supplied.

s

"Removing and Attaching the Projector Lens Unit" p.16

Control Panel

A

B

Name

[t] button

[Source Search] button

Function

Turns the projector power on or off.

Changes to the next input source that is sending an image.

s

"Automatically Detect Input Signals and Change the

Projected Image (Source Search)" p.41

C

D

E

F

[

[

[

Name

[ ]/[ ] buttons

] button

]/[ ] buttons

] /[ ] buttons

G [A/V Mute] button

Function

• Displays the Control Panel Lock screen allowing you to make settings to lock the control panel buttons.

s

"Restricting Operation" p.74

• If pressed when the Configuration menu or the Help screen is displayed, this button selects menu items and setting values.

s

"Using the Configuration Menu" p.78

s

"Using the Help" p.105

• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.

• If pressed while projecting analog RGB signals from the

Computer port or the BNC port, you can automatically optimize Tracking, Sync., and Position.

• Displays a test pattern.

s

"Displaying a Test Pattern" p.23


s


s


• Displays the Info menu from the Configuration menu.

s

"Info Menu (Display Only)" p.102


s


s


Turns the video and audio on or off.

s

"Hiding the Image and Sound Temporarily (A/V

Mute)" p.63


Name

H [Esc] button

I

[ ]/[ ] buttons

J [Menu] button

Function

• Stops the current function.

• If pressed when the Configuration menu is displayed, it moves to the previous menu level.

s


• Performs screen adjustments using the settings in

Geometric Correction from the Configuration menu.

s Settings - Geometric Correction

p.84


s


s


Displays and closes the Configuration menu.

s


Remote Control

12


13

Name

A

[ ] button

Turns the projector on.

Function

B [t] button Turns the projector off.

C Change input buttons Changes to images from each input port.

s

"Switching to the Target Image by Remote Control" p.42

The [HDBaseT] button is only available for EB-

G6750WU.

The [SDI] button is not available for this projector.

D [Auto] button If pressed while projecting analog RGB signals from the

Computer port or the BNC port, you can automatically optimize Tracking, Sync., and Position.

E [Aspect] button Each time the button is pressed, the aspect mode changes.

s

"Changing the Aspect Ratio of the Projected Image " p.47

F [Test Pattern] button Displays a test pattern.

s


G [Freeze] button Images are paused or unpaused.

s

"Freezing the Image (Freeze)" p.64

H [Menu] button

I

[ ][ buttons

][ ][ ]


s


• When the Configuration menu or the Help screen is displayed, pressing these buttons selects menu items and setting values.

s


• When using the optional wireless mouse receiver, pressing these buttons moves the pointer.

s


Name

J

[ ] button

K [Split] button

L

M

N

[Page] buttons

[[][]]

[Volume] buttons

[a][b]

[User1] button

[User2] button

[User3] button

O Numeric buttons

P [ID] button

Function

• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.

s


• Acts as a mouse's left button when using the optional wireless mouse receiver.

s


Each time the button is pressed, the image changes between projecting two images simultaneously by splitting the projected screen, or projecting one image as normal.

s

"Projecting Two Images Simultaneously (Split Screen)

" p.60

Moves to the previous or next image file when projecting images from a computer connected via a network.

[a] Decreases the volume.

[b] Increases the volume.

s

"Adjusting the Volume" p.42

Select any frequently used item from the eight available

Configuration menu items, and assign it to one of these buttons. By pressing the button, the assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/adjustments.

s

"Settings Menu" p.84

• Enter the Password.

s

"Setting Password Protection" p.72

• Use this button to enter numbers in Network settings from the Configuration menu.

Hold down this button and press the numeric buttons to select the ID for the projector you want to operate using the remote control.

s

"ID Settings" p.28


14

Name

Q [ID] switch

R Remote port

S [Help] button

T [Num] button

U [E-Zoom] buttons

[z][x]

V [Default] button

W [Esc] button

X [A/V Mute] button

Function

Use this switch to enable (On)/disable (Off) ID settings for the remote control.

s

"ID Settings" p.28

Connects the optional remote control cable set and outputs signals from the remote control.

s


When the remote control cable is plugged into this remote port, the remote control light-emitting is disabled.

Displays and closes the Help screen which shows you how to deal with problems if they occur.

s


Hold down this button and press the numeric buttons to enter passwords and numbers.

s


Enlarges or reduces the image without changing the projection size.

s

"Enlarging Part of the Image (E-Zoom)" p.64

Enabled when [Default]: Reset is displayed on the configuration menu guide. The settings being adjusted are returned to their default values.

s


• Stops the current function.

• If pressed when the Configuration menu is displayed, it moves to the previous level.

s


• Acts as a mouse's right button when using the optional wireless mouse receiver.

s



s


Mute)" p.63

Y

Z a

[

Name

[Color Mode] button

[Search] button

] button b Indicator c Remote control lightemitting area

Function

Each time the button is pressed, the Color Mode changes.

s

"Selecting the Projection Quality (Selecting Color

Mode)" p.46


s



Illuminates the buttons on the remote control for approximately 15 seconds. This is useful when using the remote control in the dark.

A light is emitted when outputting remote control signals.

Outputs remote control signals.

Replacing the remote control batteries

If delays in the responsiveness of the remote control occur or if it does not operate after it has been used for some time, it probably means that the batteries are becoming flat. When this happens, replace them with new batteries. Have two AA size alkaline or manganese batteries ready. You cannot use other batteries except for the AA size alkaline or manganese.

Attention

Make sure you read the following manual before handling the batteries.

s Safety Instructions a Remove the battery cover.

While pushing the battery compartment cover catch, lift the cover up.

Part Names and Functions b Replace the old batteries with new batteries.

Remote control operating range

Caution

Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.

If the batteries are not used correctly, they could explode or leak causing a fire, injury, or damage to the product.

c Replace the battery cover.

Press the battery compartment cover until it clicks into place.

15


16 a • To restrict reception of the operation signals from the remote control, set Remote Receiver.

s Settings - Remote Receiver

p.84

• When using a remote control provided with other Epson projectors, set the Remote Control Type.

s Extended - Operation - Remote Control Type

p.86

The operating range depends on the remote control that you use.

Removing and Attaching the Projector Lens Unit

Attaching

Attention

• Do not attach the lens unit when the projector's lens insertion section is facing up. Dust or dirt could enter the projector.

• Only use the specified lens. See the following for a list of lenses that can be used with the projector.

s


a Turn the focus ring clockwise until it cannot go any further.

Turn the torque ring on the lens unit to adjust the torque for the zoom ring.

b Insert the lens unit straight into the projector's lens socket with the white dot at the top, and then turn it clockwise until you hear it click into place.

A Tighter

B Looser c Turn the lens unit counterclockwise and make sure that it does not come out of the socket.

d Fix the lens unit removal button with the screw supplied with the lens unit.


17

Make sure you fix the lens unit removal button with the screw to prevent the lens unit from being stolen.

Removing

Attention

• Only remove the lens unit when necessary. If dust or dirt enter the projector, projection quality deteriorates and it could cause a malfunction.

• Try not to touch the lens section with your hand or fingers. If fingerprints or oils are left on the surface of the lens, projection quality deteriorates.

• If the lens shift has been done, set the lens shift to the center before replacing the lens unit.

s

"Adjusting the Position of the Projected Image (Lens Shift)" p.24

a When the lens unit removal button is fixed with a screw, remove the screw.

Attention

• Store the projector with the lens unit installed.

If the projector is stored without the lens unit, dust and dirt may get inside the projector and cause malfunctions or lower the quality of projection.

• When the projector is facing up (35 to 150 degrees) or down (-35 to -150 degrees), tighten the lens torque ring. Note that it could malfunction if it is over tightened.

b While pressing the lens unit removal button, turn the lens unit counterclockwise until you hear it click.

Part Names and Functions c Pull the lens unit straight out as it is released.

18

Preparing the Projector

This chapter explains how to install the projector and connect projection sources.

Installing the Projector

20

Installation Requirements

The projector can be mounted on a ceiling or placed on a desk. Also, it can be mounted at a tilted angle, so you can flexibly project images to various places.

Warning

• A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If installation work is not carried out correctly, the projector could fall down. This may result in injury or accidents.

Contact your dealer or the nearest address provided in the Support and

Service Guide if you want to use this installation method. s Epson Projector

Contact List

• If you use adhesives on the Ceiling mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its ceiling mount. This could cause serious injury to anyone under the ceiling mount and could damage the projector.

When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants and so on.

• Do not cover the projector's air intake vent or air exhaust vent. If either of the vents are covered, the internal temperature could rise and cause a fire.

a • An optional ceiling mount is required when suspending the projector from a ceiling.

s


• When mounted on a ceiling, set Inv Direction Button to On so that the operations and movement of the [ ], [ ], [ ], and [ ] buttons on the control panel match.

s Extended - Operation - Inv Direction Button

p.86

The projector can be installed at the following angles.

Vertical: Can be installed at any angle in a complete 360 degrees.

90

45 135

0 180

-45

-135

-90

Horizontal: Can be tilted within the range of expansion and contraction for the rear feet.

s

"Adjusting the Horizontal Tilt" p.27


21

Make sure there is a gap of at least 50 cm between the wall and the air exhaust vent and the air intake vent.

Air exhaust vent c Use the [ ][ ] buttons to set the projector's installation angle.

Each time you press one of the buttons, the angle of tilt changes by

15 degrees. Set as close to the actual setup angle as possible.

Air intake vent

When setting up multiple projectors, make sure there is a gap of at least

50 cm between the projectors.

d When you have finished making settings, use the [ ] button to select Set, and then press the [ ] button.

Changing the direction of the image (projection mode)

You can change the direction of the image using Projection mode from the

Configuration menu.

s

Extended - Projection

p.86

When installation is complete, set the Direction from the configuration menu according to the vertical installation angle.

Attention

Make sure you set Direction correctly. The lamp's operating life may be reduced if it is not set.

a b

Press the [Menu] button while projecting.

Select Direction from Extended.


When Front is the standard, the image directions for each projection mode are as follows.

Front (default) Front/Ceiling

22 a Press the [Menu] button while projecting.

s


b c d

Select Display from Extended.

Select Screen Type from Screen.

Select the screen's aspect ratio.

The shape of the background test pattern changes depending on the setting.

Rear Rear/Ceiling a • You can change the setting as follows by pressing down the [A/V

Mute] button on the remote control for about five seconds.

FrontWFront/Ceiling

• Make sure you check the Direction setting when you change the projector's installation position.

s Extended - Direction

p.86

Screen Settings

Set the Screen Type according to the aspect ratio of the screen being used.

The area where the image is displayed matches the shape of the screen.

e Press the [Menu] button to finish making settings.

a • When you change the Screen Type, adjust the aspect ratio for the projected image as well.

s


• Make sure you install the applications EasyMP Network Projection and EasyMP Multi PC Projection from the EPSON Projector

Software CD-ROM. When using older versions of the applications, images are not projected correctly. You can download the latest versions of EasyMP Network Projection and EasyMP Multi PC

Projection from the following Web site.

http://www.epson.com/

• This function does not support Message Broadcasting (an EasyMP

Monitor plugin).


23

Adjusting the position of the image on the projected screen

You can adjust the position of the image if there are margins between the edge of the image and the projected screen frame due to the Screen Type setting.

Example: When the Screen Type is set to 4:3 for EB-G6750WU e Press the [Menu] button to finish making settings.

a

The Screen Position cannot be adjusted in the following situations.

• If the Screen Type is set to 16:10 when using EB-G6750WU/EB-

G6650WU/EB-G6550WU/EB-G6450WU/EB-G6250W/EB-G6050W

• If the Screen Type is set to 4:3 when using EB-G6350/EB-G6150 You can move the image to the left and right.

a Press the [Menu] button while projecting.

s


b c d


Select Screen Position from Screen.

Use the [ ], [ ], [ ], and [ ] buttons to adjust the position of the image.

You can check the current display position by using the background test pattern.

Displaying a Test Pattern

A test pattern can be displayed to adjust the projection status without connecting video equipment.

The shape of a test pattern is according to the setting of Screen Type. Set

Screen Type first.

s

"Screen Settings" p.22

a Press the [Test Pattern] button on the remote control or the [ ] button on the control panel while projecting.


24 b Press the [ ][ ] buttons on the remote control or the [ ] button on the control panel to change the test pattern.

Using the remote control Using the control panel

Top Menu Name

Signal

Settings

Extended

Sub Menu/Items

Auto Setup

Geometric Correction s

p.43

Multi-Projection

- Brightness Level

- Edge Blending s

p.55

- Multi-screen s

p.57

* Except for custom settings of gamma a

To set menu items that cannot be set while the test pattern is being displayed or to fine-tune the projected image, project an image from the connected device.

The following image adjustments can be made while the test pattern is being displayed.

Top Menu Name

Image

Sub Menu/Items

Color Mode s

p.46

Abs. Color Temp.

Advanced

- Gamma * s

p.49

- RGB

- RGBCMY s

p.49

Reset c Press the [Esc] button to close the test pattern.

Adjusting the Position of the Projected Image

(Lens Shift)

The lens can be shifted to adjust the position of the projected image, for example, when the projector cannot be installed directly in front of the screen.

a Release the lens shift dial lock.

Installing the Projector b Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image.

25 a • We recommend setting the focus, zoom, and lens shift at least

30 minutes after you start the projection, because images are not stable right after turning on the projector.

• The image will be clearest when both the vertical and horizontal lens shift are set in the center.

The ranges within which the image can be moved are shown below.

Attention

When adjusting the image height with the vertical lens shift dial, adjust by moving the image from the bottom to the top. If it is adjusted from the top to the bottom, the image position may move down slightly after adjusting.

A Center of lens

B Projected image when lens shift is set in the center

The position of the projected image cannot be moved to both the horizontal and vertical maximum values.

c When you have finished making adjustments, lock the lens shift dial lock.


26

Adjusting the Image Size

Turn the zoom ring to adjust the size of the projected image.

W T

When using the short throw zoom lens ELPLU01

Follow the steps below to adjust the focus when the lens is shifted up, down, left, or right using the lens shift function.

a Turn the distortion ring anti-clockwise until it cannot go any further.

Correcting the Focus

You can correct the focus using the focus ring.

b Focus the image around the axis of the lens using the focus ring.

Example: When the lens shift is turned all the way down.


27 d Turn the focus ring to focus the entire screen.

If the area around the lens axis is out of focus, fine-tune by turning the distortion ring.

a

When using the short throw zoom lens ELPLU01, set Lens Type to

ELPLU01 from the Configuration menu so that keystone correction is performed correctly.

s Extended - Operation - Lens Type

p.86

c Correct screen distortion using the distortion ring.

When correcting distortion, the area around the edges of the image is also focused.

Adjusting the Image Position

Extend or retract the front foot to make adjustments. You can adjust the position of the image by tilting the projector up to 10 degrees.

A Extend the front foot.

B Retract the front foot.

a

The larger the angle of tilt, the harder it becomes to focus. Install the projector so that it only needs to be tilted at a small angle.

Adjusting the Horizontal Tilt

Extend and retract the rear feet to adjust the projector's horizontal tilt.


A Extend the rear foot.

B Retract the rear foot.

Attention

The rear feet can be attached and removed. Note that the feet will detach if they are extended more than 10 mm.

Set the projector ID a Press the [Menu] button while projecting.

s


b c d

Select Multi-Projection from Extended.

Select Projector ID, and then press the [ ] button.

Select the ID you want to set, and then press the [ ] button.

ID Settings

When an ID is set for the projector and the remote control, you can use the remote control to operate only the projector with a matching ID. This is very useful when managing multiple projectors.

a • Operation using the remote control is possible only for projectors that are within the operating range of the remote control.

s

"Remote control operating range" p.15

• When Remote Control Type is set to Simple from Operation in the configuration menu, you cannot set the remote control ID.

s

p.86

• IDs are ignored when the projector ID is set to Off or the remote control ID is set to 0.

e Press the [Menu] button to close the configuration menu.

28


Checking the Projector ID

During projection, press the [Help] button while holding the [ID] button.

Remote control

29 b While holding the [ID] button, press a number button to select a number to match the ID of the projector you want to operate.

s

"Checking the Projector ID" p.29

Remote control

When you press the buttons, the current Projector ID is displayed on the projection screen. It disappears in about three seconds.

Setting the remote control ID a Set the remote control [ID] switch to On.

Once this setting has been made, the projector that can be operated by the remote control is limited.

a

The remote control ID setting is saved in the remote control. Even if the remote control batteries are removed to replace them and so on, the stored ID setting is retained. However, if the batteries are left out for a long time, it is reset to the default value (ID0).

Setting the Time

You can set the time for the projector. The set time is used for scheduling and for wireless LAN authentication.

s

"Scheduling Function" p.69

Installing the Projector a • When you turn on the projector for the first time, the message "Do you want to set the time?" is displayed. When you select Yes, the screen from step 4 is displayed.

• When Time/Schedule Protection is set to On in Password

Protection , settings related to the date and time cannot be changed.

You can make changes after setting Time/Schedule Protection to

Off .

s

"Managing Users (Password Protection)" p.72

a Press the [Menu] button while projecting.

s


b c d

Select Operation from Extended.

Select Date & Time, and then press the [ ] button.

Make settings for the date and time.

Use the soft keyboard to enter the date and time.

s

"Soft keyboard operations" p.91

Date & Time

Submenu

Date

Time

Function

Set today's date.

Set the current time.

30

Submenu Function

Time Difference (UTC) Set the time difference from Coordinated

Universal Time.

Set The settings made in Date & Time are applied.

Daylight Saving Time

Submenu Function

Daylight Saving Time Set whether or not (On/Off) to activate the daylight saving time.DST Adjustment (min) adjusts the time difference between the standard time and the daylight saving time.

DST Start

DST End

Set

Set the date and time to start the daylight saving time.

Set the date and time to end the daylight saving time.

The settings made in Daylight Saving Time are applied.

Internet Time

Submenu

Internet Time

Internet Time Server

Set

Function

Set to On to update the time automatically through an Internet time server.

Input the IP address for an Internet time server.

The settings made in Internet Time are applied.

a

When changing settings, make sure you select Set, and then press the [ ] button.


Connecting Equipment

31

The port name, location, and connector orientation differ depending on the source being connected.

Connecting a Computer

To project images from a computer, connect the computer using one of the following methods.

A When using the supplied computer cable

Connect the computer's display output port to the projector's Computer port.

You can output audio from the projector's speaker by connecting the audio output port on the computer to the projector's Audio1 port using a commercially available audio cable.

B When using a commercially available 5BNC cable

Connect the computer's display output port to the projector's BNC port.

You can output audio from the projector's speaker by connecting the audio output port on the computer to the projector's Audio2 port using a commercially available audio cable.

C When using a commercially available HDMI cable

Connect the HDMI port on the computer to the projector's HDMI port.

You can send the computer's audio with the projected image.

D When using a commercially available DisplayPort cable

Connect the computer's DisplayPort to the projector's DisplayPort.

You can send the computer's audio with the projected image.


4

Computer

Audio1

BNC

Audio2

HDMI HDMI OUT

4

DisplayPort DisplayPort OUT a • Change the audio output from Audio Settings.

s Extended - A/V Settings - Audio Settings

p.86

• If audio is not sent using an HDMI or DisplayPort cable, connect a commercially available audio cable to the Audio3 port to send the audio. Set HDMI Audio

Output or DisplayPort Audio Output to Audio3.

s Extended - A/V Settings - Audio Settings - HDMI Audio Output, DisplayPort Audio Output

p.86

• Some commercially available DisplayPort cables come with a lock. When removing the cable, press the button on the cable's connector section and pull out the cable.

32


33

Connecting Image Sources

To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.

A When using a commercially available video cable

Connect the video output port on the image source to the projector's Video port.

You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio cable.

B When using a commercially available S-video cable

Connect the S-video output port on the image source to the projector's S-Video port.

You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio cable.

C When using an optional component video cable (D-sub/component converter) s


Connect the component output port on the image source to the projector's Computer port.

You can output audio from the projector's speaker by connecting the audio output port on the video equipment to the projector's Audio1 port using a commercially available audio cable.

D When using a commercially available component video cable (RCA) and a BNC/RCA adapter

Connect the component output port on the video equipment to the projector's BNC port (R/Cr/Pr, G/Y, B/Cb/Pb).

You can output audio from the projector's speaker by connecting the audio output port on the video equipment to the projector's Audio2 port using a commercially available audio cable.

E When using a commercially available HDMI cable

Connect the HDMI port on the image source to the projector's HDMI port.

You can send the image source's audio with the projected image.


Video

Video

AUDIO OUT (L,R)

5

Audio-L/R

S-Video

Audio-L/R

S-Video

AUDIO OUT (L,R)

4

Computer

Audio1

4

BNC(R/Cr/Pr, G/Y, B/Cb/Pb)

Audio2

5

HDMI

Attention

• If the input source is on when you connect it to the projector, it could cause a malfunction.

• If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.

Y

Cb/Pb

Cr/Pr

AUDIO OUT

Y

Cb/Pb

Cr/Pr

AUDIO OUT

HDMI OUT

34

Connecting Equipment a • Change the audio output from Audio Settings.


p.86

• If audio is not sent using an HDMI cable, connect a commercially available audio cable to the Audio3 port to send the audio. Set HDMI Audio Output to

Audio3 .

s Extended - A/V Settings - Audio Settings - HDMI Audio Output

p.86

• If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.

• When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".

Connecting External Equipment

You can output images and audio by connecting an external monitor or speaker.

A When outputting images to an external monitor

Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.

B When outputting audio to an external speaker

Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.

35

Monitor Out

Audio Out

D-Sub

Audio IN

Connecting Equipment a • Make the following settings to output image and audio even when the projector is in standby mode.

Set Standby Mode to Communication On.

s Extended - Standby Mode

p.86

Set A/V Output to Always On.

s Extended - A/V Settings - A/V Output

p.86

• When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external output.

Connecting a LAN Cable

Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN cable.

By connecting a computer to the projector over a network, you can project images and check the status of the projector.

36

LAN a

To prevent malfunctions, use a category 5 or higher shielded LAN cable.

Connecting an HDBaseT Transmitter (EB-G6750WU Only)

Connect the optional HDBaseT Transmitter with a commercially available 100BASE-TX LAN cable.

s



HDBaseT a • Make sure you read the User's Guide supplied with the HDBaseT transmitter carefully before use.

• Use a category 5e or category 6 shielded LAN cable.

• When connecting or disconnecting the LAN cable, make sure you turn off the power for the projector and the HDBaseT transmitter.

• When performing Ethernet communication or serial communication, or when using the wired remote control via HDBaseT port, set Control Communications to On from the Configuration menu.

s Extended - HDBaseT - Control Communications

p.86

Note that when Control Communications is set to On, the projector's LAN port, RS-232C port, and Remote port are disabled.

37


Installing the Wireless LAN Unit

a Open the air filter cover.

Slide the air filter cover operation knob, and open the air filter cover.

c Install the Wireless LAN unit.

d Secure the stopper with a screw.

b Remove the stopper for the Wireless LAN unit.

e Close the air filter cover.

38


Attaching the Cable Cover

By attaching the cable cover, you can hide the connected cables giving a nice, clean finish to the projector installation. (The illustrations are of a projector installed on a ceiling.)

Attaching a Bundle the cables together with a commercially available tie.

39 c Tighten the two screws on the cable cover. (You can tighten the screws with your fingers.) b Insert the tabs on the cable cover into the two slots on the back of the projector.

Basic Usage

This chapter explains how to project and adjust images.

Projecting Images

Automatically Detect Input Signals and Change the Projected Image (Source Search)

Press the [Search] button on the remote control or the [Source Search] button on the control panel to project images from the port currently receiving an image.

Using the remote control Using the control panel a

The following screen is displayed while no image signals are input.

41

* EB-G6750WU only

When two or more image sources are connected, press the [Search] button on the remote control or the [Source Search] button on the control panel until the target image is projected.

When your video equipment is connected, start playback before beginning this operation.

Projecting Images

Switching to the Target Image by Remote Control

You can change directly to the target image by pressing the following buttons on the remote control.

The input ports for each button are shown below.

Remote control

42

• Press the [Volume] button on the remote control to adjust the volume.

[ a ] Decreases the volume.

[ b ] Increases the volume.

Remote control

Input Port

• Adjust the volume from the Configuration menu.

s Settings - Volume

p.84

Caution

Do not start at high volume.

A sudden excessive volume may cause loss of hearing. Always lower the volume before powering off, so that you can power on and then gradually increase the volume.

E Changes to images from a computer connected via the network.

F EB-G6750WU only

Adjusting the Volume

You can adjust the volume using one of the following methods.

Adjusting Projected Images

Correcting Distortion in the Projected Image

You can correct keystone distortion in projected images using one of the following methods.

• H/V-Keystone

Manually correct distortion in the horizontal and vertical directions independently.

s

"H/V-Keystone" p.43

43

• Arc Correction

Fine adjustment of the curved distortion caused by slack or shrinkage of the screen.

s

"Arc Correction" p.45

• Quick Corner

Manually correct the four corners independently.

s

"Quick Corner" p.44

• Point Correction

Corrects slight distortion which occurs partially, or adjusts the image position in an overlapping area when projecting from multiple projectors.

s

"Point Correction" p.53

a • By pressing the [

] button on the control panel, you can perform the selected adjustment method directly.

• You cannot combine multiple adjustment methods.

H/V-Keystone

Manually correct distortion in the horizontal and vertical directions independently. The angle of vertical and horizontal tilt for the projector can be corrected up to 30 degrees against the screen.

a b


Select Geometric Correction from Settings.


44 c Select H/V-Keystone, and then press the [ ] button.

If the message "If this setting is changed, the image may be distorted."is displayed, press the [ ] button.

d Use the [ ][ ] buttons to select the correction method, and then use the [ ][ ] buttons to make the corrections.

V-Keystone e When you are done, press the [Menu] button to exit the correction menu.

Quick Corner

This allows you to manually correct each of the four corners of the projected image separately.

a b c



Select Quick Corner, and then press the [ ] button.


d Use the [ ], [ ], [ ], and [ ] buttons to select the corner you want to adjust, and then press the [ ] button.

H-Keystone a

When you correct keystone distortion, the projected image may be reduced.


45 a

If the [Esc] button is pressed for at least 2 seconds, the confirm default reset screen is displayed.

Select Yes to reset the result of Quick Corner corrections.

e Use the [ ], [ ], [ ], and [ ] buttons to correct the position of the corner.

When you press the [ ] button, the screen shown in step 4 that allows you to select the area to be corrected is displayed.

If the message "Cannot adjust any further." is displayed while adjusting, you cannot adjust the shape any further in the direction indicated by the gray triangle.

Arc Correction a b c



Select Arc Correction, and then press the [ ] button.


d Use the [ ], [ ], [ ], and [ ] buttons to select the area you want to adjust, and then press the [ ] button.

f Repeat procedures 4 and 5 as needed to adjust any remaining corners.

g When you are done, press the [Menu] button to exit the correction menu.

When selecting a corner, you can adjust the two sides next to the corner.

a

If the [Esc] button is pressed for at least 2 seconds, the confirm default reset screen is displayed.

Select Yes to reset the result of Arc Correction.

e Use the [ ], [ ], [ ], and [ ] buttons to adjust the shape.


46 f g h

If the triangle in the direction you are adjusting the shape turns gray, as shown in the screenshot below, you cannot adjust the shape any further in that direction.

Press the [Esc] button to return to the previous screen.

Repeat procedures from 4 to 6 as needed to adjust any remaining parts.

When you are done, press the [Menu] button to exit the correction menu.

Selecting the Projection Quality (Selecting Color

Mode)

You can easily obtain the optimum image quality simply by selecting the setting that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected.

Dynamic

Mode

Presentation

Theatre

Photo *1

Sports *2 sRGB

DICOM SIM *1

Multi-Projection

Application

Ideal for use in a bright room. This is the brightest mode.

Ideal for making presentations using color materials in a bright room.

Ideal for watching films in a dark room. Gives images a natural tone.

Ideal for projecting still pictures, such as photos, in a bright room. The images are vivid and brought into contrast.

Ideal for watching TV programmes in a bright room. The images are vivid and brought to life.

Ideal for images that conform to the sRGB

g

color standard.

Ideal for projecting X-ray photographs and other medical images. This produces images with clear shadows. The projector is not a medical device and cannot be used for medical diagnosis.

Ideal for projecting from multiple projectors.

Minimize the color tone difference between each projected image.

* 1 This can only be selected when inputting RGB signals, or when LAN is selected as the input source.

* 2 This can only be selected when inputting component video signals, or when the source is Video or S-Video.


Each time you press the [Color Mode] button, the Color Mode name is displayed on the screen and the Color Mode changes.

Remote control

• 3D Presentation

• 3D Theatre

• 3D Multi-Projection a

This projector arranges the direction of polarizing projection for R

(red), G (green), and B (blue). It is not necessary to inverse left and right eye G (green) image signals.

47 a

You can set Color Mode from the Configuration menu.

s Image - Color Mode

p.81

Changing the Aspect Ratio of the Projected

Image

You can change the Aspect Ratio

g

of the projected image to suit the type, the ratio of height and width, and the resolution of the input signals.

Available aspect modes vary depending on the Screen Type currently set.

a

Set the Screen Type before changing the aspect ratio.

s


Projecting 3D images

By using two projectors, you can project passive 3D images. You need the following optional items to project and view 3D images. Make sure you read the notes in the user's guides supplied with the optional items.

• Polarizer (ELPPL01)

• Passive 3D Glasses (ELPGS02A/ELPGS02B) s


When projecting 3D images, set 3D Images to On from the Configuration menu.

s Signal - 3D Setup - 3D Images

p.82

The following color modes are available when projecting 3D images. When projecting using the optional polarizers (ELPPL01), you can view images at their optimal color tint.

• 3D Dynamic

Changing methods

Each time you press the [Aspect] button on the remote control, the aspect mode name is displayed on the screen and the aspect ratio changes.

Remote control


48

The aspect mode changes as follows.

Screen Type: 4:3

Auto or Normal

4:3

16:9

Native *

* Only computer images and images from the HDMI port/HDBaseT port

Screen Type: 16:9

Auto or Normal

Full

Zoom

Native

Screen Type: 16:10

Auto or Normal

16:9

Full

Native

Zoom

Native

Auto

Aspect Mode

Normal

4:3

16:9

Full

Zoom

Explanation

Projects in an appropriate aspect ratio based on information from the signal being input.

Projects while retaining the aspect ratio of the input image.

Projects at an aspect ratio of 4:3.

Projects at an aspect ratio of 16:9.

Projects at the full size of the projected screen.

Projects by enlarging the input image to the full width of the projected screen while retaining the aspect ratio. Areas that exceed the edges of the projected screen are not projected.

Projects to the center of the projected screen at the resolution of the input image. Areas that exceed the edges of the projected screen are not projected.


49 a • You can also set the aspect ratio from the Configuration menu.

s Signal - Aspect

p.82

• If parts of the computer image are missing, set the Resolution setting to Wide or Normal from the Configuration menu, according to the resolution of the computer.

s Signal - Resolution

p.82

s Image - Advanced - Gamma

p.81

Select and adjust the correction value s Image - Advanced - Gamma

p.81

Adjusting the Image

Hue, Saturation, and Brightness Adjustment

The Hue, Saturation, and Brightness for each of the R (red), G (green), B

(blue), C (cyan), M (magenta) and Y (yellow) color components can be adjusted.

Make settings from the configuration menu.

s

Image - Advanced - RGBCMY

p.81

Gamma Adjustment

Adjusts differences in the coloring for the projected image that occurs depending on the connected device.


When a smaller value is selected, the dark areas of images become brighter, but the color saturation for lighter areas may become weaker. When a larger value is selected, you can reduce the overall brightness of the image to make the image sharper.

If you select DICOM SIM from Color Mode on the Image menu, select the adjustment value according to the projection size.

• If the projection size is 120 inches or less, select a large value.

• If the projection size is 120 inches or more, select a small value.

a

Medical images may not be reproduced correctly according to your settings and screen specifications.

Adjust while viewing the image s

Image - Advanced - Gamma - Customized - Adjust it from the image

p.81


Move the cursor on the projected image to the part where you want to change the brightness, then press the [ ] button. Use the [ ][ ] buttons to adjust the value.

50

Adjust using the gamma adjustment graph s

Image - Advanced - Gamma - Customized - Adjust it from the graph

p.81

Adjust while looking at the gamma adjustment graph.

Frame Interpolation (EB-G6750WU/EB-G6650WU/EB-G6550WU/EB-

G6450WU only)

The current and previous frames are used to create intermediate frames, interpolating to produce smooth-moving images. You can resolve clumsymoving images, such as frame skipping when projecting a fast moving image.


s Signal - Frame Interpolation

p.82


You can select the level of interpolation: Low, Normal or High. Set to Off if noise occurs after setting them.

51

Useful Functions

This chapter explains useful tips for giving presentations, and the Security functions.

Multi-Projection Function

53

When projecting to a wide screen from multiple projectors, you can adjust the difference of brightness and color tone between each projected image to create a seamless screen.

There are two general methods of projecting from multiple projectors.

U Projecting different images from each projector, and creating a seamless screen

V Projecting the same image from each projector, using the Scale function to project a large image

Follow the steps below.

1.

Set an ID for the projector and the remote control s p.28

2.

Adjust the position of the projected image s

p.53

3.

Checking the Color Mode

4.

Adjust the edges of the images (edge blending) s

p.55

5.

Adjusting to match colors

Adjusting the Position of the Projected Image

Adjust the position of the projected image, starting from the adjustments that have larger corrections.

1.

Projector's position (angle) s

p.20

2.

Lens shift/Zoom s

p.24

3.

Geometric Correction

• Quick Corner s

p.44

• Point Correction s

p.53

a • We recommend setting the focus, zoom, and lens shift at least 30 minutes after you start the projection, because images are not stable right after turning on the projector.

• The Test Pattern can be displayed to adjust the projection status without connecting video equipment. s

p.23

• When projecting from multiple projectors, the correction is easier if you use the image in dot by dot format, that can be displayed without being enlarged or reduced.

Here we will take

U

as an example.

The steps for V are the same, but use the Scale function to adjust the position of the projected image. s

p.58

Point Correction

Corrects slight distortion which occurs partially, or adjusts the image position in an overlapping areas.


Divides the projected image by the grid and corrects the distortion by moving the point of intersection from side to side and up and down.

54 f Use the [ ], [ ], [ ], and [ ] buttons to move to the point you want to correct, and then press the [ ] button.

a b c



Select Point Correction, and then press the [ ] button.


d Select Point Correction, and then press the [ ] button.

g Use the [ ], [ ], [ ], and [ ] buttons to correct distortion.

Point Correction : Performs point correction.

Pattern Color : Select the color of the grid when performing corrections.

Reset : Resets all corrections for Point Correction to their default values.

e Select the number of grid lines (3x3, 5x5, or 9x9), and then press the [ ] button.

To continue to correct another point, press the [Esc] button to return to the previous screen, and then repeat steps 6 and 7.

a

Each time you press the [ image and the grid.

] button, you can show or hide the h When you are done, press the [Menu] button to exit the correction menu.


Checking the Color Mode

Set the Color Mode to Multi-Projection (or 3D Multi-Projection for 3D images). s

p.46

Adjust the Edges of the Images (Edge Blending)

When multiple projectors are lined up and projecting images, you can create a seamless screen.

c d e

Select Brightness Level, and then press the [ ] button.

Select 1 to 5 as the brightness.


Performing edge blending a Press the [Menu] button while projecting.

s


b c


Select Edge Blending, and then press the [ ] button.

The following screen is displayed.

Adjusting the brightness of the lamp

Before performing edge blending, adjust so that the lamp brightness is the same for each projector.

Adjust so that all projectors are the same brightness as the darkest lamp.

You can adjust the brightness in five levels.

a • Set Power Consumption to Normal.

• Even if you adjust the Brightness Level, the brightness of each lamp may not match exactly.

• Brightness Level is not available for EB-G6450WU.

a b



55


Submenu

Edge Blending

Top Edge/Bottom

Edge/Right Edge/Left

Edge

Blend Curve

Guide Display

Pattern Guide

Guide Colors

Function

Set to On to activate the edge blending function.

Set to Off when not projecting from multiple projectors.

Blending : Set to On to activate the edge blending function towards where you are setting, and the brend range will be shaded.

Blend Range : Adjusts the range to be shaded.

Adjustment is possible at the level of one pixel. The maximum range is 45% of the resolution.

You can select from three ways of shading.

Set to On to display the guide on the edge blending setting range.

Set to On to display a guide to match the position of the edge blending setting range.

You can select the combination of guide colors from the three.

d Turn on Edge Blending.

(1) Select Edge Blending, and then press the [ ] button.

(2) Select On, and then press the [ ] button.

(3) Press the [Esc] button.

e Display the guide.

(1) Select Guide Display, and then press the [ ] button.



a

If the guide is not clear, you can change the color of the guide on Guide Colors.

f Display a pattern.

(1) Select Pattern Guide, and then press the [ ] button.



g Set Top Edge/Bottom Edge/Right Edge/Left Edge.

(1) Select Top Edge/Bottom Edge/Right Edge/Left Edge to set the edge blending, and then press the [ ] button.

(2) Select Blending, and then press the [ ] button.



56


(5) In Blend Range, adjust the range to be shaded.

The value for when the overlapped range and the guide are in the same position is the best.

a b c



Select Multi-screen, and then press the [ ] button.


57


(7) Set Guide Display and Pattern Guide to Off.

h Set Blend Curve.

(1) Select Blend Curve, and then press the [ ] button.

(2) Select the amount of shading from 1 to 3, and then press the [ ] button.

The edges of the images are adjusted.

(3) Press the Menu button to finish making settings.

Adjusting to Match Colors

Follow the steps below to adjust the brightness of the projected image and the color balance that was adjusted by performing edge blending.

a

The brightness and color may not be uniform even after making adjustments.

Adjustment Level : There are five levels from white, gray, and up to black. Adjust each level individually.

Brightness Correct.

: Adjust from black to white for each color tone.

Color Correct. (G/R) : Adjust the color tone for green and red.

Color Correct. (B/Y) : Adjust the color tone for blue and yellow.

a

Whenever the [ ] button is pressed, the screen changes between the projected image and the adjustment screen.

d Select Adjustment Level, and then use the [ ][ ] buttons to set the adjustment level.

e Select Brightness Correct., and then use the [ ][ ] buttons to adjust the brightness.

f Select Color Correct. (G/R) or Color Correct. (B/Y), and then use the [ ][ ] buttons to adjust the color.

Multi-Projection Function g h

Return to step 4 and adjust each level.

When you are done, press the [Menu] button to exit the correction menu.

Scaling an Image (Scale)

A section of the image is cropped and displayed. This allows you to create one large image by combining images projected from multiple projectors.

a Press the [Menu] button while an image is being projected.

s


b c

Select Scale from Signal.

Set Scale to On.

(1) Select Scale, and then press the [ ] button.


(3) Press the [Esc] button to return to the previous screen.

d Set Scale Mode.

(1) Select Scale Mode, and then press the [ ] button.

(2) Select Zoom Display or Full Display, and then press the [ ] button.

Zoom Display : Adjusts according to the image currently displayed.

58

Full Display : Adjusts according to the projector's panel size (the maximum area in which an image can be displayed).


Multi-Projection Function e Adjust the scale.

Select the adjustment method with the [ ][ ] buttons, then adjust using the [ ][ ] buttons.

+: Enlarges or reduces an image horizontally and vertically at the same time.

Scale Vertically : Enlarges or reduces an image vertically.

Scale Horizontally : Enlarges or reduces an image horizontally.

f Adjust the Image Display Range.

(1) Select Image Display Range, and then press the [ ] button.

(2) Use the [ ], [ ], [ ], and [ ] buttons to scroll the image.

Adjust the coordinates and size of each image while viewing the screen.

(3) Press the [Menu] button to finish making settings.

59

Projection Functions

60

Projecting Two Images Simultaneously (Split

Screen)

You can simultaneously project images from two sources on the right and left of the screen.

Operating procedures

Projecting on a split screen a Press the [Split] button while projecting.

The currently selected input source is projected on the left of the screen.

Remote control a • The following input source combinations cannot be projected using the split screen function.

Computer - BNC, S-Video - Video, HDMI - HDBaseT (EB-

G6750WU only)

• You cannot project the same input source on both sides (left and right) of the screen.

a

You can perform the same operations from the configuration menu.

s Settings - Split Screen

p.84

b Press the [Menu] button.

The Split Screen Setup screen is displayed.

c Select Source, and then press the [ ] button.

Projection Functions d Select each input source for Left and Right.

b Select Swap Screens, and then press the [ ] button.

The projected images on the left and right are swapped.

61 a

You can perform the same operations using the following procedure.

s



s


e Select Execute, and then press the [ ] button.

To switch the source during split screen projection, start the procedure from step 2.

Switching the left and right screens

Use the following procedure to switch the projected images displayed on the left and right screens.

a Press the [Menu] button during split screen projection.

Switching the left and right image sizes a b c

Press the [Menu] button during split screen projection.

Select Screen Size, and then press the [ ] button.

Select the screen size you want to display, and then press the [ ] button.


62

The projected images will appear as shown below after setting the screen size.

Equal Larger Left c Select the audio you want to output, and then press the [ ] button.

When you select Auto, audio is output for the largest screen.

If the screens are the same size, audio is output for the screen on the left.

Larger Right a • You cannot enlarge both the left screen and right screen images at the same time.

• When one image is enlarged, the other image is reduced.

• Depending on the video signals that are input, the images on the left and right may not appear to be the same size even if Equal is set.

Changing the audio a b

Press the [Menu] button during split screen projection.

Select Audio Source, and then press the [ ] button.

Ending the split screen

Press the [Esc] button to end split screen.

The following steps can also be used to end the split screen.

• Press the [Split] button on the remote control.

• Select Exit Split Screen on the Split Screen Setup screen. s

p.60

Restrictions during split screen projection

Operating restrictions

The following operations cannot be performed during split screen projection.

• Setting the configuration menu

• E-Zoom

• Changing the aspect mode

• Using the [User1], [User2], or [User3] buttons on the remote control

• Help can be displayed only when image signals are not input or when an error or warning notification is displayed.


• The user's logo is not displayed.

Restriction relating to images

• The default values for the Image menu are applied to the image on the right screen. However, the settings for the image projected on the left screen are applied to the image on the right screen for Color Mode,

Abs. Color Temp.

, and Advanced. Also, the Frame Interpolation settings from the Signal menu are applied to the image projected on the left screen.

• Auto Iris is not available.

s Image - Auto Iris

p.81

Hiding the Image and Sound Temporarily (A/V

Mute)

You can use this when you want to focus the audience's attention on what you are saying, or if you do not want to show details such as when you are changing between files during presentations from a computer.

A/V Mute is applied or released each time you press the [A/V Mute] button.

Remote control a

63

• When A/V Mute Release is set to A/V Mute from the configuration menu, the following operations can still be performed without releasing A/V mute.

s Extended - Operation - A/V Mute Release

p.86

- Change the source with the change input buttons on the remote control.

s


- Control the projector from a computer using communication commands.

s

"Monitoring and Controlling" p.145

A/V mute is only released by pressing the [A/V Mute] button, or by sending an A/V mute Off command.

• When projecting moving images, the images and sound continue to be played back while A/V Mute is on. It is not possible to resume projection from the point where A/V Mute was activated.

• You can select the screen displayed when the [A/V Mute] button is pressed from the Configuration menu.

s Extended - Display - A/V Mute

p.86

• The lamp is still lit during A/V Mute, so the lamp hours continue to accumulate.


Freezing the Image (Freeze)

When Freeze is activated on moving images, the frozen image continues to project on the screen, so you can project a moving image one frame at a time like a still photo. Also, you can perform operations such as changing between files during presentations from a computer without projecting any images if the Freeze function is activated beforehand.

Each time you press the [Freeze] button, Freeze turns on or off.

Remote control a Start E-Zoom.

Press the [ z ] button to display the Cross ( ).

Remote control

64 a • Audio does not stop.

• When projecting moving images, the images continue to be played back while the screen is frozen. It is not possible to resume projection from the point where the screen was frozen.

• If the [Freeze] button is pressed while the Configuration menu or the Help screen is displayed, the menu or the Help screen that is displayed is closed.

• Freeze still works while E-Zoom is being used.

Enlarging Part of the Image (E-Zoom)

This is useful when you want to expand images to see them in greater detail, such as graphs and tables.

b Move the Cross ( ) to the area of the image that you want to enlarge.

Remote control

Projection Functions c Enlarge.

Remote control

[z] button: Expands the area each time it is pressed. You can expand quickly by holding the button down.

[x] button: Reduces images that have been enlarged.

[Esc] button: Cancels E-Zoom.

a

• During enlarged projection, press the [

[ ] buttons to scroll the image.

], [ ], [ ], or

• E-Zoom is unavailable when Scale is set to On.

s Signal - Scale

p.82

Saving a User's Logo

You can save the image that is currently being projected as a User's Logo.

a

Once a User's Logo has been saved, the logo cannot be returned to the factory default.

a Project the image you want to save as the User's Logo, and then press the [Menu] button.

s


b Select User's Logo from Extended.

65 a • When User's Logo Protection from Password Protection is set to On, a message is displayed and the User's Logo cannot be changed. You can make changes after setting User's Logo

Protection to Off.

s


• If User's Logo is selected when Geometric Correction, E-

Zoom or Aspect are being performed, the function currently being performed is temporarily cancelled.

c When the message "Choose this image as the User's Logo?" is displayed, select Yes.

a

When you press the [ ] button, the screen size may change depending on the signal to match the actual resolution of the image signal.

d Move the box to select the part of the image to use as the User's

Logo.

You can perform the same operations from the projector's control panel.

Remote control a

You can save at 400x300 dots in size.

Projection Functions e When you press the [ ] button and the message "Select this image?" is displayed, select Yes.

f g

Select the zoom factor from the zoom setting screen.

When the message "Save this image as the User's Logo?" is displayed, select Yes.

The image is saved. After the image has been saved, the message

"Completed." is displayed.

a

When a User's Logo is saved, the previous User's Logo is erased.

66

Memory Function

The settings for the image currently displayed are saved as a memory, allowing you to load them when necessary. Settings for the following menu items are saved in the memory.

Submenu

Image

Signal

Top Menu

Settings

Extended

All setting items

3D Setup

Progressive

Frame Interpolation

Noise Reduction

Mosquito NR

Video Range

Scale

Overscan

Image Processing

Power Consumption

Brightness Level

Edge Blending

Multi-screen

Saving/Loading/Erasing the Memory

a Press the [Menu] button while an image is being displayed.

s


b Select Memory from Settings.

67 c Select the function you want to perform, then press the [ ] button.

You can only perform Load Memory and Save Memory when an image is displayed.

Memory Function

68

Function

Rename Memory

Explanation

Changes the memory name. Select the memory name you want to change, and then press the [ ] button. Enter the memory name using the soft keyboard.

s


When you have finished, move the cursor over

Finish , and then press the [ ] button.

When a memory has already been saved, the memory name and its color mode are displayed.

Function

Load Memory

Save Memory

Erase Memory

Explanation

Loads the saved memory. When you select a memory and press the [ ] button, the settings applied to the current image are replaced with the settings from the memory.

The settings for the image currently displayed are saved as a memory. When you select a memory name and press the [ ] button, the settings are saved.

Erases the registered memory. When you select a memory name and press the [ ] button, a message is displayed. Select Yes, and then press the

[ ] button to erase the selected memory. You can erase all memories from Reset Memory.

s

Reset - Reset Memory p.101

a

If the mark on the left of the memory name is turned green, it means the memory has already been registered. When you select a registered memory, a message is displayed asking you to confirm that you want to overwrite the memory. If you select

Yes , the previous settings are deleted and the current settings are registered.

Scheduling Function

You can schedule turning the projector power on/off and switching the input source, as events in the schedule. Registered events are executed automatically at the specified time on the specified dates or weekly.

Warning

Do not place flammable objects in front of the lens. If you set the schedule to turn on the projector automatically, any flammable objects placed in front of the lens could cause a fire.

Saving a Schedule

a • You can set or adjust the date and time for the projector in Date &

Time from the configuration menu.

s

"Setting the Time" p.29

• When Time/Schedule Protection is set to On in Password

Protection , settings related to the scheduling function cannot be changed. You can make changes after setting Time/Schedule

Protection to Off.

s


Setting Methods a Press the [Menu] button while projecting.

s


b c

Select Schedule Settings from Extended.

Select Add New from Schedule.

69 d Set the schedule.

Submenu Name

Event Settings

Date / Time Settings

Function

Select an operation of the projector when the event is executed. Select No Change for items that you do not want to change when the event occurs.

You can set the following item operations.

• Power

• Source

• Power Consumption

• A/V Mute

• Volume

Set the date, day of the week, and time to execute the event. Use the soft keyboard to enter the date and time.

s


When you have finished, move the cursor over

Finish , and then press the [ ] button.

Scheduling Function e Select Save, and then press the [ ] button.

To register additional schedules, repeat steps 3 to 5.

f Select Setup complete, and then select Yes to finish saving.

a

A calendar is displayed on the Schedule Settings screen (the screen in step 3). The indicator turns on when an event is saved. ( : one-time event; : periodic event; : communication on/off; : event invalid)

Use the [ ][ ] buttons to highlight and check the schedule registered for that day.

Editing a schedule a Press the [Menu] button while projecting.

s


b c

Select Schedule Settings from Extended.

Use the [ ][ ] buttons to highlight the date containing the schedule you want to edit.

70 d Highlight the schedule you want to edit, and then press the [Esc] button.

Scheduling Function a

A repeat icon is displayed for periodic schedules.

e Perform editing from the menu displayed.

a

To delete all registered schedules, select Schedule Reset, and then select Yes. Select Setup complete, and then select Yes to delete the schedules.

71

Submenu Name

On/Off

Edit

Clear

Add New

Function

Enable or disable the selected schedule. When a schedule is enabled, the indicator turns green.

Edit the content of the selected schedule. Select

Save , and then press the [ ] button to complete the editing.

Deletes the selected schedule.

Save a new schedule. Select Save, and then press the

[ ] button to complete the saving.

f Select Setup complete, and then select Yes to finish editing.

Security Functions

72

The projector has the following enhanced security functions.

• Password Protection

You can limit who can use the projector.

• Control Panel Lock/Remote Control Button Lock

You can prevent people changing the settings on the projector without permission.

s

"Restricting Operation" p.74

• Anti-Theft Lock

The projector is equipped with the following anti-theft security device.

s

"Anti-Theft Lock" p.75

• User's Logo Protection

Even if someone tries to change the User's Logo set by the owner of the projector, it cannot be changed. When User's Logo Protection is set to

On , the following setting changes for the User's Logo are prohibited.

• Capturing a User's Logo

• Setting Display Background, Startup Screen, or A/V Mute from

Display s

Extended - Display

p.86

• Network Protection

When Network Protection is set to On, changing the settings for

Network is prohibited.

s

"Network Menu" p.89

• Time/Schedule Protection

When Time/Schedule Protection is set to On, changing settings for the projector's system time or schedules is prohibited.

Managing Users (Password Protection)

When Password Protection is activated, people who do not know the password cannot use the projector to project images even if the projector power is on. Furthermore, the user's logo that is displayed when you turn on the projector cannot be changed. This acts as an anti-theft function as the projector cannot be used even if it is stolen. At the time of purchase,

Password Protection is not activated.

Kinds of Password Protection

The following three kinds of Password Protect settings can be made according to how the projector is being used.

• Power On Protection

When Power On Protection is On, you need to enter a preset password after the projector is plugged in and turned on (this also applies to Direct

Power On). If the correct password is not entered, projection does not start.

Setting Password Protection

Use the following procedure to set Password Protect.

a During projection, hold down the [Freeze] button for about five seconds.

The Password Protection setting menu is displayed.

Remote control


73

Remote control a

If Password Protection is already activated, you must enter the password.

If the password is entered correctly, the Password Protection setting menu is displayed.

s

"Entering the Password" p.73

b Select the type of Password Protect you want to set, and then press the [ ] button.

(4) Re-enter the password.

The message "Password accepted." is displayed.

If you enter the password incorrectly, a message is displayed prompting you to re-enter the password.

Entering the Password

When the password entry screen is displayed, enter the password using the remote control.

While holding down the [Num] button, enter the password by pressing the numeric buttons.

c Select On, and then press the [ ] button.

Press the [Esc] button to return to the screen in step 2.

d Set the password.

(1) Select Password, and then press the [ ] button.

(2) When the message "Change the password?" is displayed, select Yes and then press the [ ] button. The default password is set to "0000". Change this to your own desired Password. If you select No, the screen displayed in step 2 is displayed again.

(3) While holding down the [Num] button, enter a four digit number using the numeric buttons. The number entered is displayed as "* * * *". When you enter the fourth digit, the confirmation screen is displayed.

When you enter the correct password, Password Protect is temporarily released.


Attention

• If an incorrect password is entered three times in succession, the message

"The projector's operation will be locked." is displayed for approximately five minutes, and then the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet and then reinsert it and turn the projector's power back on. The projector displays the password entry screen again so that you can enter the correct password.

• If you have forgotten the password, make a note of the "Request Code: xxxxx" number that appears on the screen and contact the nearest address provided in the Epson Projector Contact List.

s Epson Projector Contact List

• If you continue to repeat the above operation and input the wrong password thirty times in succession, the following message is displayed and the projector does not accept any more password entries."The projector's operation will be locked. Contact Epson as described in your documentation." s Epson Projector Contact List

Restricting Operation

The following two kinds of operation restriction functions are available with the projector.

• Control Panel Lock

This is useful at events or shows when you want to deactivate all buttons during projection or at schools when you want to limit button operation.

• Remote control button lock

This function deactivates buttons except for main buttons needed for basic remote control operation, to prevent mistakes in operations.

Control Panel Lock

Perform one of the following to lock the operation buttons on the control panel. Even if the control panel is locked, you can still use the remote control as usual.

• Full Lock

All of the buttons on the control panel are locked. You cannot perform any operations from the control panel, including turning the power on or off.

• Partial Lock

All of the buttons on the control panel, except for the [ t

] button, are locked.

a Press the [ ] button on the control panel during projection to display the Control Panel Lock screen.

a

You can also make settings in Control Panel Lock from the configuration menu.

s Settings - Control Panel Lock

p.84

b

74

Select either Full Lock or Partial Lock according to your purpose.

c Select Yes when the confirmation message is displayed.

The control panel buttons are locked according to the setting you chose.


75 a

You can release the control panel lock by one of the following two methods.

• Use the remote control to set Control Panel Lock to Off from the configuration menu.

s Settings - Control Panel Lock

p.84

• Press and hold down the [

] button on the control panel for about seven seconds, a message is displayed and the lock is released.

Remote control button lock

This function locks the following buttons on the remote control.

Each time the [Help] button is pressed for at least 5 seconds, the remote control button lock turns on or off.

Remote control a

Even if the remote control button lock is on, the following operations are possible.

• Resetting default for the Remote Receiver setting

• Releasing the remote control button lock

Anti-Theft Lock

The projector is equipped with the following types of anti-theft security devices.

• Security slot

The security slot is compatible with the Microsaver Security System manufactured by Kensington.

See the following for more details on the Microsaver Security System.

s http://www.kensington.com/

• Security cable installation point

A commercially available theft-prevention wire lock can be passed through the installation point to secure the projector to a desk or pillar.


Installing the wire lock

Pass an anti-theft wire lock through the installation point.

See the documentation supplied with the wire lock for locking instructions.

76

Configuration Menu

This chapter explains how to use the Configuration menu and its functions.

Using the Configuration Menu

This section explains how to use the Configuration menu.

Although steps are explained using the remote control as an example, you can perform the same operations from the control panel. Check the guide under the menu for the available buttons and their operations.

a Display the Configuration menu screen.

c Select a submenu item.

d Change settings.

b Select a top menu item.

a

When [Default]: Reset is displayed on the guide, and you press the [Default] button on the remote control, the settings being adjusted are returned to their default values.


78

List of Functions

Configuration Menu Table

Settable items vary depending on the model being used and the image signal and source being projected.

Top Menu Name

Image menu s

p.81

Signal menu s

p.82

Submenu Name

Color Mode

Brightness

Contrast

Color Saturation

Tint

Sharpness

Abs. Color Temp.

Advanced

Auto Iris

Auto Setup

Resolution

Tracking

Sync.

Position

3D Setup

Progressive

Frame Interpolation

(EB-G6750WU/EB-

G6650WU/EB-

G6550WU/EB-

G6450WU only)

Items or Setting Values

Dynamic, Presentation, Theatre,

Photo, Sports, sRGB, DICOM SIM,

Multi-Projection, 3D Dynamic, 3D

Presentation, 3D Theatre, and 3D

Multi-Projection

-24 - 24

-24 - 24

-32 - 32

-32 - 32

-5 to 5, and Advanced

5000K to 10000K

Gamma, RGB, and RGBCMY

On and Off

On and Off

Auto, Wide, Normal, Manual

-

-

-

3D Images

Off, Video, and Film/Auto

Off, Low, Normal, High

79

Top Menu Name

Settings menu s

p.84

Extended menu s

p.86

Submenu Name

Noise Reduction

Mosquito NR

Video Range

Input Signal

Video Signal

Aspect


Off, NR1, and NR2

On and Off

Auto, Normal, and Expanded

Auto, RGB, and Component

Auto, NTSC, NTSC4.43, PAL, M-

PAL, N-PAL, PAL60, and SECAM

Normal, Auto, 4:3, 16:9, Full,

Zoom, and Native

Scale

Overscan

-

Auto, Off, 4%, and 8%

Image Processing Fast, Fine

DisplayPort EQ Setting 1, 2

Geometric Correction H/V-Keystone, Quick Corner, Arc

Correction, Point Correction

Split Screen

Control Panel Lock

Power Consumption

Volume

Remote Receiver

User Button

-

Full Lock, Partial Lock, and Off

Normal, Temp Interlock, and ECO

0 - 20

Test Pattern

Memory

Display

-

Front/Rear, Front, Rear, and Off

User Button 1, User Button 2, and

User Button 3

Load Memory, Save Memory,

Erase Memory, Rename Memory

Menu Position, Messages, Display

Background, Startup Screen, A/V

Mute, Air Filter Notice, Screen,

Panel Alignment, and Color

Uniformity


Top Menu Name Submenu Name

User's Logo

Projection

Direction

Operation

Info menu s

p.102

A/V Settings

Standby Mode

HDBaseT (EB-

G6750WU only)

Multi-Projection

Schedule Settings

Language

Lamp Hours

Source

Input Signal

Resolution

Video Signal

Refresh Rate

Sync Info


-

Front, Front/Ceiling, Rear, and

Rear/Ceiling

0 Degree to 180 Degree to -15

Degree

Direct Power On, Sleep Mode,

Sleep Mode Timer, High Altitude

Mode, BNC Sync Termination,

Remote Control Type, Inv

Direction Button, Startup Source

Search, A/V Mute Release, Beep,

Lens Type, and Date & Time

A/V Output, Monitor Out, and

Audio Settings

Communication On and

Communication Off

Control Communications

-

-

-

-

-

-

-

Brightness Level (not available for

EB-G6450WU), Edge Blending,

Multi-screen, and Projector ID

-

27 languages

Top Menu Name

Reset menu s

p.103

Submenu Name

Status

Serial Number

Event ID

Reset All

Reset Lamp Hours

Reset Memory

-

-

-

-

-

-


Network menu

Top Menu Name

Basic menu s

p.91

Wireless LAN menu s

p.92

Submenu Name

Projector Name

Web Remote Password

Projector Keyword

Wireless LAN Power

Wi-Fi Protected Setup

Wireless LAN system

Connection Mode

SSID Auto Setting

SSID

Search Access Point

Channel

SSID Display

DHCP

IP Address

Subnet Mask

Gateway Address

-

-

-

-


-

On and Off

-

On and Off

802.11b/g and

802.11b/g/n

-

-

Quick and Advanced

On and Off

1ch, 6ch, and 11ch

On and Off

On and Off

80


81

Top Menu Name

Security menu s

Wired LAN menu s

p.97

Administrator Settings menu s

p.98

p.94

Submenu Name

IP Address Display

Region Code

Security


On and Off

-

Open, WPA/WPA2-PSK,

WPA/WPA2-EAP

DHCP

IP Address

Subnet Mask

Gateway Address -

-

-

On and Off

IP Address Display

Administrator Password -

On and Off

Network Host Name

PJLink Password

-

-

Web Control Password -

Monitor Password -

Secure HTTP

Mail Notification -

On and Off

Manage Certificates

SNMP

Priority Gateway

-

-

Wired, Wireless

AMX Device Discovery On and Off

Crestron RoomView On and Off

Bonjour

EPSON Message

Broadcasting

On and Off

On and Off

Image Menu

Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each image signal.

s

"Automatically Detect Input Signals and Change the Projected Image

(Source Search)" p.41

Submenu

Color Mode

Brightness

Function

You can select the quality of the image to suit your surroundings.

s

"Selecting the Projection Quality (Selecting Color Mode)" p.46

You can adjust the image brightness.

Contrast You can adjust the difference between light and dark in the images.

Color Saturation (Adjustment is only possible when component video or composite video images are being input.)

You can adjust the color saturation for the images.


82

Tint

Submenu

Sharpness

Function

(Adjustment is possible when a component video signal is being input. If a composite video signal is input, adjustment is only possible when NTSC signals are being input.)

You can adjust the image tint.

Standard : You can adjust the image sharpness. To make moredetailed settings, select Advanced.

Advanced : The following four items can be set.

Thin Line Enhancement : If this parameter is set to a positive value, details such as hair or fabric patterns will be enhanced.

Thick Line Enhancement : If this parameter is set to a positive value, the outline, background, and the other main parts of the objects in the image will be enhanced to show them clearly.

Vert. Line Enhancement : If this parameter is set to a positive value, vertical lines in the image are enhanced.

Horiz. Line Enhancement : If this parameter is set to a positive value, horizontal lines in the image are enhanced.

Abs. Color Temp.

You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. The image is tinted blue when a high value is selected and tinted red when a low value is selected.

Advanced You can make adjustments by choosing the following items.

Gamma : You can adjust the coloring by selecting one of the gamma correction values, or referring to the projected image or a gamma graph.

RGB : You can adjust the individual R (red), G (green), and B

(blue) components of the offset and gain.

RGBCMY : You can adjust the hue, saturation, and brightness of each color R (red), G (green), B (blue), C (cyan), M (magenta), Y

(yellow) individually.

Submenu

Auto Iris

Reset

Function

(This item can be set only if Color Mode is set to Dynamic,

Theatre , 3D Dynamic or 3D Theatre. It cannot be set if Edge

Blending is set to On.)

Set to On to adjust the iris to obtain the optimum light for images being projected.

The setting is stored for each Color Mode.

You can reset all adjustment values for the Image menu to their default settings. See the following to return all menu items to their default settings.

s

"Reset Menu" p.103

Signal Menu

Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each image signal.


Submenu

Auto Setup

Resolution

Tracking

Function

(Only available when an analog RGB computer signal is being input.)

Set to On to automatically adjust Tracking, Sync., and Position to the optimum state when the input signal changes.


Set to Auto to automatically identify the resolution of the input signal. If images are not projected correctly when set to Auto, for example if some of the image is missing, set to Wide for wide screens, or set to Normal for 4:3 or 5:4 screens depending on the connected computer.

Manual allows you to specify the resolution. This is ideal when connected computer is fixed.


You can adjust computer images when vertical stripes appear in the images.

83

Submenu

Sync.

Position

3D Setup

Progressive

Function


You can adjust computer images when flickering, fuzziness, or interference appear in the images.

You can adjust the display position up, down, left, and right when a part of the image is missing so that the whole image is projected.

When projecting passive 3D images using two projectors, set 3D

Images to On.

Interlace

g (i) signal is converted to Progressive g

(p). (IP conversion)

Off : Ideal for images with a large amount of movement.

Video : Ideal for general video images.

Film/Auto : This is ideal for movie films, computer graphics, and animation.

Frame Interpolation (EB-

G6750WU/EB-

G6650WU/EB-

G6550WU/EB-

G6450WU only)

You can play fast moving images smoothly by producing intermediate frames between the original frames.

Noise Reduction (This cannot be set when Image Processing is set to Fast.)

Smoothes out the roughness in progressive images. There are two modes. Select your favorite setting. It is recommended that this is set to Off when viewing image sources in which noise is very low, such as for DVDs.

Mosquito NR

Video Range

(This cannot be set when Image Processing is set to Fast.)

When a progressive signal is being input, you can reduce the wavy noise that occurs in lines between areas with dramatic changes in colors.

Select the video range for the input signal from the HDMI port, the DisplayPort, HDBaseT port (EB-G6750WU only). Set to

Expanded if you are concerned about misadjusted black levels or blown out highlights in the image.


84

Submenu

Input Signal

Video Signal

Aspect

Scale

Overscan

Image Processing

DisplayPort EQ

Setting

Function

You can select an input signal from the Computer port or BNC port.

If set to Auto, the input signal is set automatically according to the connected equipment.

If colors do not appear correctly when set to Auto, select the appropriate signal according to the connected equipment.

You can select an input signal from the Video port or S-Video port. If set to Auto, video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being projected when set to Auto, select the appropriate signal according to the connected equipment.

You can set the aspect ratio

g for projected images.

s


When using multiple projectors to project one image, adjust the range of the image displayed by each projector.

s

"Scaling an Image (Scale)" p.58

(This setting can only be adjusted when a component video signal is being input.)

Changes the output image ratio (the range of the projected image). You can set the cropping range to 4% or 8%. When set to

Auto , this is automatically adjusted according to the input signal.

Changes settings for image processing.

Fast : Images are displayed quicker.

Fine : Images are displayed in higher quality.

Adjusts the DisplayPort input signal level depending on the devices connected to the DisplayPort. If there is a lot of interference in the image, or if a problem such as no image being projected occurs, select 1 or 2, and then confirm the selection.

Submenu

Reset

Settings Menu

Function

You can reset all adjustment values on the Signal menu to their default settings, except for Input Signal, Image Processing and

DisplayPort EQ Setting .

See the following to return all menu items to their default settings.

s

"Reset Menu" p.103


85

Submenu

Geometric Correction

Split Screen

Control Panel

Lock

Power Consumption

Volume

Function

You can correct distortion.

s

"Correcting Distortion in the Projected Image" p.43

• H/V-Keystone:

Adjust V-Keystone and H-Keystone to correct horizontal and vertical keystone distortion.

• Quick Corner:

Select and correct the four corners of the projected image.

• Arc Correction:

Fine adjustment of the curved distortion caused by slack or shrinkage of the screen.

• Point Correction:

Divides the projected image into a grid and corrects the distortion by moving the selected point of intersection from side to side and up and down.

You can split the screen into two screens.

s

"Projecting Two Images Simultaneously (Split Screen) " p.60

You can use this to restrict operation of the projector's control panel.

s

"Control Panel Lock" p.74

When set to Normal, the lamp is at its brightest.

When set to Temp Interlock, if the surrounding temperature * gets too high, the lamp automatically dims to control the operating temperature.

When set to ECO, the power consumption during projection drops and the fan noise is reduced.

You can adjust the volume. Setting values are saved for each source.

Remote Receiver

Submenu

User Button

Test Pattern

Memory

Reset

Function

You can limit the reception of the operation signal from the remote control.

When set to Off, you cannot perform any operations from the remote control. If you want to make operations from the remote control, hold down the [Menu] button on the remote control for at least 15 seconds to reset the setting to its default value.

Select the items from the Configuration menu that you want to assign to the [User1], [User2], and [User3] buttons on the remote control. The following items can be assigned.

Power Consumption , Info, Progressive, Geometric

Correction , Multi-Projection, Resolution, Memory, or

Image Processing

You can display a test pattern to adjust the projection without connecting other equipment when you set up the projector.

s


Perform operations and make settings for the memory function.

s

"Memory Function" p.67

You can reset all adjustment values on the Settings menu to their default settings, except for User Button and

Memory .


s

"Reset Menu" p.103

* Operating temperature of +40˚C at an altitude of 0 to 1499 m, and +35˚C at an altitude of 1500 to 3048 m.


Extended Menu

86

Submenu

Display

User's Logo *

Function

You can make settings related to the projector's display.

Menu Position : Select the position to display the menu on the projected screen.

Messages : When set to Off, the following items will not be displayed.

Item names when the Source, Color Mode, or Aspect is changed, messages when no signal is being input, and warnings such as High Temp Warning.

Display Background * : You can set the screen background to Black, Blue, or Logo when no image signal is available.

Startup Screen * : Set to On to display the User's Logo when projection starts.

A/V Mute * : You can set the screen displayed when the [A/V Mute] button is pressed to Black, Blue, or

Logo .

Air Filter Notice : You can set whether or not (On/Off) to enable Air Filter Notice. When this is set to On and a clog in the air filter is detected, the message is displayed on the screen.

Screen : (This setting is unavailable when projecting images from a computer over a network.) Set the aspect ratio and position of the projected screen according to the type of screen being used.

s


Panel Alignment : Correct color misalignments (red and blue) in the screen.

s

"Panel Alignment" p.134

Color Uniformity : Adjusts the color tone balance for the whole screen.

s

"Color Uniformity" p.135

You can change the user's logo that is displayed as a background during Display Background, A/V Mute, and so on.

s

"Saving a User's Logo" p.65


Submenu

Projection

Direction

Function

Select from one of the following projection methods depending on how the projector is installed.

Front , Front/Ceiling, Rear, and Rear/Ceiling

You can change the setting as follows by pressing down the [A/V Mute] button for about five seconds.

FrontWFront/Ceiling

RearWRear/Ceiling

Set this parameter according to the installation status of the projector.

s

"Installation Requirements" p.20

87

Submenu

Operation

Function

Direct Power On : Set to On to turn on the projector simply by plugging it in.

When the power cord is plugged in, note that the projector turns on automatically in cases such as a power outage being restored.

Sleep Mode : When set to On, this automatically stops projection when no image signal is being input and no operations are carried out.

Sleep Mode Timer : When Sleep Mode is set to On, you can set the time before the projector automatically turns off within a range of 1 to 30 minutes.

High Altitude Mode : Set to On when using the projector above an altitude of 1500 m.

BNC Sync Termination : Set the termination for the signal from the BNC port. This should usually be set to Off. Set to

On when analog (75Ω) termination such as for switchers is necessary.

Remote Control Type : You can select Normal or Simple depending on the type of remote control.

Set this item to Normal to use the remote control provided with this projector. When Simple is selected, you can use the remote control provided with other Epson projectors to operate this projector. This is useful if you want to use a remote control that you are already familiar with to operate the projector.

However, you cannot use the remote control provided with this projector if this is set to Simple. Make sure that the setting is correct because, if the projector is mounted on the ceiling or somewhere hard to reach, changing it back to

Normal may be difficult. Additionally, you cannot use the functions that are not equipped with this projector or the remote control which you use.

Inv Direction Button : Set this to On when the projector is installed on a ceiling.


Submenu Function

Startup Source Search : Set whether or not (On/Off) to automatically detect the image signal being input when the projector is turned on.

A/V Mute Release : (This item cannot be set if User's Logo

Protection from Password Protection is set to On.

s

p.72

)

When set to A/V Mute, you can only release A/V mute by pressing the [A/V Mute] button (or by sending an A/V mute Off command).

When set to Any Button, A/V mute is released when any operation is performed on the projector.

s

"Hiding the Image and Sound Temporarily (A/V Mute)" p.63

Beep : When this is set to On, the confirmation buzzer beeps to notify you that the power turns on or off, or cooling down is finished.

Lens Type : Set this to ELPLU01 when the optional short throw zoom lens (ELPLU01) is attached. When using another lens, set this to Others.

Date & Time : Make system time settings for the projector.

s


88

Submenu

A/V Settings

Function

A/V Output : (This item can be set only if Standby Mode is set to Communication On) Set this to Always On when the projector is in standby status and you want to output audio and images to an external device.

Monitor Out : Select the image source output to an external monitor when the projector is in standby status. When set to Auto, analog RGB signals from the Computer port or the

BNC port are output depending on which source was selected when the projector was turned off.

Audio Settings : Perform the following audio related settings.

• Audio Output: Select the audio to be output when projecting images from the Computer port, BNC port,

S-Video port or Video port. When set to Auto, audio is output from the audio input port corresponding to each image input port.

s

"Connecting Equipment" p.31

• DisplayPort Audio Output: Select the audio source when projecting images from the DisplayPort. If you select

DisplayPort , audio for the image is output as it is. If you select Audio3, audio is output from the Audio3 port.

• HDMI Audio Output: Select the audio source when projecting images from the HDMI port. If you select

HDMI , audio for the image is output as it is. If you select

Audio3 , audio is output from the Audio3 port.

Standby Mode If you set Communication On, you can perform the following operations even if the projector is in standby mode.

• Monitor and control the projector over a network.

• Output audio and images to an external device. (Only when A/V Output is set to Always On.)

• Communication from the HDBaseT port is enabled. (Only when Control Communications is set to On.)


89

Submenu

HDBaseT (EB-

G6750WU only)

Function

Make settings when the optional HDBaseT Transmitter is connected to the HDBaseT port.

Control Communications : When set to On, Ethernet communication from the HDBaseT port, serial communication, and control using the wired remote control connected to the optional HDBaseT Transmitter are all enabled. (When this is enabled, the projector's LAN port,

RS-232C port, and Remote port are disabled.)

Multi-Projection Make settings when projecting from multiple projectors.

s

"Multi-Projection Function" p.53

Brightness Level (not available for EB-G6450WU): When the brightness of each lamp differs, set the lamp brightness level between 1 and 5. This item can be adjusted only when

Power Consumption is set to Normal from the Settings menu.

Edge Blending : Corrects a border between multiple images to create a seamless screen.

s

"Adjust the Edges of the Images (Edge Blending)" p.55

Multi-screen : You can adjust the tint and brightness of each projected image.

s

"Adjusting to Match Colors" p.57

Projector ID : Set the ID from 1 to 9.Off indicates that no

ID is set.

s

"ID Settings" p.28

Schedule Settings

Language

You can set the projector's schedule so that it performs a specific operation at a pre-scheduled time.

s

"Scheduling Function" p.69

You can set the language for messages and menus.

Submenu

Reset

Function

You can reset all adjustment values for the Extended menu to their default settings. However, the following items are not reset.

Screen Type , Screen Position, Projection, Direction, High

Altitude Mode , Remote Control Type, Inv Direction

Button , Startup Source Search, Lens Type, A/V Output,

Monitor Out , Standby Mode, Control Communications,

Multi-screen , Projector ID, and Language


s

"Reset Menu" p.103

* When User's Logo Protection is set to On in Password Protection, settings related to user's logo cannot be changed. You can make changes after setting

User's Logo Protection to Off.

s


Network Menu

When Network Protection is set to On in Password Protection, a message is displayed and the network settings cannot be changed. Set Network

Protection to Off and then configure the network.

List of Functions s


Submenu

Net. Info. - Wireless LAN

Net. Info. - Wired

LAN

Function

Displays the following network setting status information.

• Connection Mode

• Antenna Level

• Projector Name

• SSID

• DHCP

• IP Address

• Subnet Mask

• Gateway Address

• MAC Address

• Region Code

Displays the following network setting status information.

• Projector Name

• DHCP

• IP Address

• Subnet Mask

• Gateway Address

• MAC Address

90

Submenu

Network Configuration

Function

The following menus are available for setting Network items.

Basic , Wireless LAN, Security, Wired LAN, Administrator

Settings , and Reset a

By using a Web browser of a computer connected to the projector on a network, you can set functions and control the projector. This function is called Web Control. You can easily enter text using a keyboard to make settings for Web Control such as Security settings.

s

"Changing Settings Using a Web Browser (Web Control)" p.145

Notes on operating the Network menu

Selecting from the top menu and sub menus, and changing selected items is the same as making operations from the Configuration menu.

When done, make sure you go to the Setup complete menu, and select Yes,

No , or Cancel. When you select Yes or No, you are returned to the

Configuration menu.


Yes : Saves the settings and exits the Network menu.

No : Does not save the settings and exits the Network menu.

Cancel : Continues displaying the Network menu.

a • You cannot use colons (:) for Network menu items.

• Except for SSID, you cannot use spaces for Network menu items.

• The following four characters cannot be entered using the soft keyboard. Enter these characters using a Web browser.

“ * , ; s


Soft keyboard operations

The Network menu contains items that require input of alphanumerics during setup. In this case, the following software keyboard is displayed. Use the [ ][ ][ ][ ] buttons to move the cursor to the desired key, and then press the [ ] button to enter the selected character. Enter figures by holding down the [Num] button on the remote control, and pressing the numeric buttons. After inputting, press Finish on the keyboard to confirm your input. Press Cancel on the keyboard to cancel your input.

Basic menu

91

• Each time the CAPS key is selected and the [ ] button is pressed, it sets and changes between upper case and lower case letters.

• Each time the SYM1/2 key is selected and the [ ] button is pressed, it sets and changes the symbol keys for the section enclosed by the frame.

The following types of character can be entered.

Numbers

Letters

Symbols

0123456789

ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz

! # $ % & ' ( ) + - . / < = > ? @ [ ¥ ] ^ _ { | } ~

Submenu Function

Projector Name The projector's name is displayed when using the supplied application EasyMP Network Projection and EasyMP Multi PC

Projection.

When editing, you can enter up to 16 single-byte alphanumeric characters. (" * + , / ; < = > ? [ ¥ ] ` | cannot be used.)


92

Submenu

Web Remote

Password

Projector Keyword

Function

Set a password to use Web Remote. You can enter up to 8 singlebyte alphanumeric characters. (* cannot be used)

Web Remote is a computer function that allows you to operate the projector by using the Web browser on a computer connected on a network.

s


When set to On, you have to enter the keyword when you try to connect the projector to a computer via a network. As a result, you can prevent presentations from being interrupted by connections from other computers.

Normally this should be set to On.

s EasyMP Network Projection Operation Guide

Wireless LAN menu

To connect the projector to a computer using a wireless LAN, install the

Wireless LAN unit (ELPAP07).

s

"Installing the Wireless LAN Unit" p.38

Submenu

Wireless LAN

Power

Wi-Fi Protected

Setup

Wireless LAN system

Function

Set this to On when connecting the projector and a computer via a wireless LAN. If you do not want to connect via wireless LAN, turn it Off to prevent unauthorized access by others.

Set this when connecting to a network via a wireless LAN access point compatible with WPS (Wi-Fi Protected Setup)

g . You can

easily connect the projector to the access point and make security settings.

s

"Making a WPS (Wi-Fi Protected Setup) Connection with a

Wireless LAN Access Point " p.142

Sets the wireless LAN system. Normally this should be set to

802.11b/g/n . The connection method is selected automatically according to the access point settings.

In an area that does not support 802.11n, only 802.11b/g is displayed.


Submenu

Connection

Mode

SSID Auto Setting

SSID

Search Access

Point

Channel

SSID Display

DHCP

Function

Set the connection mode to use when connecting the projector and a computer via a wireless LAN.

If you select Quick, a small network is created automatically by the projector and computer. It is used with EasyMP Network

Projection. If SSID Auto Setting is set to On, the projector becomes an easy access point; if it is set to Off, the network is

created in Ad hoc mode g

.

If you select Advanced, the connection is established in infrastructure mode

g through the access point installed.

If Connection Mode is set to Quick, when you set this to On, you can search for the projector more quickly from among multiple projectors. SSID is set automatically.

When connecting to multiple projectors from 1 computer in

Quick, set this to Off, and set the same SSID in all the projectors that will connect.

Enter an SSID. When an SSID is provided for the wireless LAN system in which the projector participates, enter the SSID.

You can enter up to 32 single-byte alphanumeric characters. (^ cannot be used.) Set SSID to blank or ANY to establish an ANY connection.

When Connection Mode is set to Advanced, you can search for surrounding access points, and set the SSID to be connected from those access points. Depending on the access point settings, they may not be displayed in the list. You must set security separately.

s

"Search Access Point screen" p.94

You can select the channels used to connect in Quick mode. If interference from other signals occurs, use a different channel.

To prevent the SSID from being displayed on the LAN Standby screen, set this to Off.

You can set whether or not (On/Off) to use DHCP

g

.

If this is set to On, you cannot set any more addresses.

93

Submenu

IP Address

Subnet Mask

Gateway Address

IP Address Display

Region Code

Function

You can input the IP address

g assigned to the projector.

You can enter a number from 0 to 255 in each field of the address.

However, the following IP addresses cannot be used. 0.0.0.0,

127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from

0 to 255)

You can input the Subnet Mask

g

for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following subnet masks cannot be used.

0.0.0.0, 255.255.255.255

You can input the IP address for the gateway for the projector.


However, the following Gateway addresses

g cannot be used.

0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)

To prevent the IP address from being displayed on the LAN

Standby screen, set this to Off.

This is a specific string of the wireless LAN module.


Search Access Point screen

Detected access points are displayed in a list.

94

Security menu

When the Wireless LAN unit is installed, it is strongly recommended that you set security.

Submenu

Refresh

Function

Searches for the access point again.

Indicates an already set access point.

Indicates the access points where security is set.

If you select an access point where security has not been set, the

Wireless LAN menu is displayed.

If you select an access point where security has been set, the

Security menu is displayed. Select a type of security according to the security settings for the access point.


Submenu

Security

Function

You can select a type of security.

• When Quick is selected

Open : Security is not set.

WPA2-PSK(AES) (only when SSID Auto Setting is set to

On ): Communication is performed using WPA2 security.

Uses AES method for encryption. When establishing a connection from a computer to the projector, enter the value set in the passphrase.

• When Advanced is selected

Open : Security is not set.

WPA2-PSK(AES) : Connects in WPA personal mode.

Encryption method is selected automatically according to the access point settings. Set a passphrase which is the same for the access point.

WPA/WPA2-EAP : Connects in WPA enterprise mode.

Encryption method is selected automatically according to the access point settings. Select this item when using

LEAP.

a

You cannot set WEP as an encryption method for this projector.

When WPA/WPA2-PSK is selected

Submenu

Passphrase

Function

Enter the passphrase. You can enter at least 8 and up to 63 singlebyte alphanumeric characters. When the passphrase is entered and the [ ] button is pressed, the value is set and displayed as an asterisk (*).

When using it with EasyMP Network Projection, you do not need to input the passphrase in the computer if it is the initial

(default) passphrase.

It is recommended to change the passphrase periodically for the purpose of security. If the network settings are initialized, it returns to the initial passphrase.

s

"Reset menu" p.101

You can enter up to 32 characters on the Configuration menu.

When entering more than 32 characters, use your Web browser to enter the text.

s


In Quick mode, the initial passphrase is set.

95


When WPA/WPA2-EAP is selected

Submenu

EAP Method

Function

Set the protocol for authentication.

PEAP : Authentication protocol widely used in Windows Server.

PEAP-TLS : Authentication protocol used in Windows Server.

Set when using client certificate.

EAP-TLS : Authentication protocol widely used to use a client certificate.

EAP-Fast , LEAP: Select this when these authentication protocols are used.

96

Submenu

User name

Function

Enter a user name to be used for authentication. You can enter up to 64 single-byte alphanumeric characters.

If you select PEAP-TLS or EAP-TLS, the user name obtained automatically from the client certificate is displayed. You can change the user name if the authentication server requires another user name.



s


If you also need to enter a domain name, add the domain name before the user name separated by a backslash.

Password Enter a password to be used for authentication. You can enter up to 64 single-byte alphanumeric characters. When the password is entered and Finish is selected, the value is set and displayed as an asterisk (*).



s


Client Certificate Displays the Issued to, Issued by, and Validity period information set in the stored client certificate. It is blank if the certificate is not set.

Verify Server

Certificate

CA certificate

Set to On to perform verification for the authentication server certificate. To verify a server certificate, you need to set CA certificate.

s

"Setting Certificates" p.146

Displays the Issued to, Issued by, and Validity period information set in the stored CA certificate. It is blank if the certificate is not set.


Submenu

Setting RADIUS

Server Name

RADIUS Server

Name

Verify Exp. date of Server Cert.

Function

Set to On to perform authentication of the server name during server certificate verification. By specifying the server name, you can reduce the risk of connecting to an invalid authentication server.

Specify the authentication server name.

You can enter up to 32 single-byte alphanumeric characters. (^ cannot be used.)

Set to On to perform verification of the certificate's validity period during server certificate verification.

Wired LAN menu

97

Submenu

IP Address

Subnet Mask

Gateway Address

IP Address Display

Function


g assigned to the projector.


However, the following IP addresses cannot be used.


You can input the Subnet Mask

g

for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following subnet masks cannot be used.

0.0.0.0, 255.255.255.255

You can input the IP address for the gateway for the projector.


However, the following Gateway addresses

g cannot be used.


To prevent the IP address from being displayed on the LAN

Standby screen, set this to Off.

Submenu

DHCP

Function

You can set whether or not (On/Off) to use DHCP

g

.

If this is set to On, you cannot set any more addresses.


Administrator Settings menu

Submenu

Administrator

Password

Function

Enter the password for the Administrator Settings menu for network settings.

You can enter up to 16 single-byte alphanumeric characters. (* cannot be used.)

If the administrator password is not set, click OK with an empty password box.

Network Host

Name

This name is used to identify the projector on a network. Use for

Web control, "Connect to a Network Projector" and so on.

When editing, you can enter up to 15 single-byte alphanumeric characters. (The only symbols you can use are - _. The first character should be a letter, and the last character should be a letter or a number.)

PJLink Password Set a password to use when you access the projector using compatible PJLink software.

You can enter up to 32 single-byte alphanumeric characters.

(Symbols cannot be used.) s

"About PJLink" p.151

98

Submenu

Web Control

Password

Function

Set a password to use when making settings and controlling the projector using Web Control. You can enter up to 8 single-byte alphanumeric characters. (* cannot be used.) Web Control is a computer function that allows you to set up and control the projector by using the Web browser on a computer connected on a network.

s


Monitor Password

Secure HTTP

Set a password to use EasyMP Monitor.

You can enter up to 16 single-byte alphanumeric characters. (* cannot be used.)

To strengthen security, communication between the projector and computer in Web control is encrypted. When setting security with Web control, it is recommended to set this to On.

Mail Notification Goes to the Mail Notification setting menu.

s

"Mail Notification menu" p.99

Manage Certificates

Goes to the Manage Certificates settings menu.

s

"Manage Certificates menu" p.100

SNMP Goes to the SNMP settings menu.

s

"SNMP menu" p.100

Priority Gateway For the priority gateway, select either Wired or Wireless.

AMX Device Discovery

When you want to allow the projector to be detected by AMX

Device Discovery g , set this to On. Set this to Off if you are not

connected to an environment controlled by a controller from

AMX or AMX Device Discovery.

Crestron Room-

View

Set this to On only when monitoring or controlling the projector over the network using Crestron RoomView ® . Otherwise, set this to Off.

s

"About Crestron RoomView ® " p.152

Changes in projector settings take effect upon restarting.

When this is set to On, the following functions are not available.

• Web control

• Message Broadcasting (EasyMP Monitor plugin)


Submenu

Bonjour

EPSON Message

Broadcasting

Function

Set this to On when connecting to the network using Bonjour.

See Apple's Web site for more information on the Bonjour service.

http://www.apple.com/

You can switch the EPSON Message Broadcasting function to enable or disable.

You can download Message Broadcasting and its Operation

Guide from the following Web site.

http://www.epson.com

Mail Notification menu

When this is set, you receive an email notification if a problem or warning occurs in the projector.

s

"Reading Error Notification Mail" p.148

99

Submenu

SMTP Server

Port Number

Email Address 1/

Email Address 2/

Email Address 3

Setting a Notification Event

Function


g for the SMTP server for the

projector.




0 to 255)

You can input the port number for the SMTP server. The default value is 25. You can input numbers between 1 to 65535.

You can input the email address of the destination to send the notification email to. You can register up to three destinations.

You can enter up to 64 single-byte alphanumeric characters for the email addresses. ( " ( ) , ; < > [ ¥ ] cannot be used.)



s


The address for destination 1 is the mail notification sender's address.

You can select the problems or warnings to be notified about by email. When the selected problem or warning occurs in the projector, an email is sent to the specified Email Address notifying that a problem or warning has occurred. You can select multiple items from the displayed items.

Submenu Function

Mail Notification Set to On to send an email to the preset addresses when a problem or warning occurs with a projector.


Manage Certificates menu

100

Submenu

Web Server Certificate

Function

(This item can only be set when Secure HTTP is set to On.)

The Issued to, Issued by, and Validity period information on the certificate set in the projector is displayed. This information is not displayed when a Self-signed Certificate is set.

Select Clear to delete the stored certificate.

a

Web Control is used to set certificates.

s

"Setting Certificates" p.146

SNMP menu

Submenu Function

Client Certificate Displays the Issued to, Issued by, and Validity period information set in the stored client certificate. It is blank if the certificate is not set. You need to set Client Certificate when

WPA/WPA2-EAP is selected in Security, and PEAP-TLS or

EAP-TLS are selected in EAP Method.


CA certificate

Self-signed Certificate

Displays the Issued to, Issued by, and Validity period information set in the stored CA certificate. It is blank if the certificate is not set. You need to set CA certificate when

WPA/WPA2-EAP is selected in Security, when verifying the authentication server certificate.


(This item can only be set when Secure HTTP is set to On.)

The Issued to, Issued by, and Validity period information on the certificate maintained by the server function in the projector is displayed. This information is not displayed if Web Server

Certificate is set.

Select Refresh to update the self-signed certificate.

Submenu

SNMP

Function

Set to On to monitor the projector using SNMP

g . To monitor

the projector, you need to install the SNMP manager program on your computer. SNMP should be managed by a network administrator. The default value is Off.


Submenu

Trap IP Address

1/Trap IP Address 2

Community

Name

Function

You can register up to two IP addresses for the SNMP trap notification destination.




0 to 255)

Set the community name of SNMP. You can enter up to 32 singlebyte alphanumeric characters. (The only symbol you can use is

@.)

Reset menu

Resets all of the network settings.

101

Submenu

Reset network settings.

Function

To reset all of the Network settings, select Yes.

When you reset the network settings , the Passphrase,

Administrator Password and Manage Certificates menu settings change back to their default values, and the certificates are deleted.

After you reset all the settings, the Basic menu appears.


102

Info Menu (Display Only)

Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the source currently being projected.

Submenu

Status

Serial Number

Event ID

Function

This is information about errors that have occurred on the projector.

This information may be needed if service is required.

Displays the projector's serial number.

Displays the application error log.

s

"About Event ID" p.122

* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H", "11H", and so on.

Submenu

Lamp Hours

Source

Input Signal

Resolution

Video Signal

Refresh Rate

Sync Info

Function

You can display the cumulative lamp operating time * .

When the lamp replacement time is reached, the characters are displayed in yellow.

You can display the source name for the connected equipment currently being projected.

You can display the content of Input Signal set in the

Signal menu according to the source.

You can display the resolution.

You can display the settings for Video Signal in the Signal menu.

You can display the refresh rate

g

.

You can display the image signal information.

This information may be needed if service is required.


Reset Menu

Submenu

Reset All

Reset Lamp

Hours

Reset Memory

Function

You can reset all items in the Configuration menu to their default settings.

The following items are not reset to their defaults: Input Signal,

User's Logo , all items for Network menus, Lamp Hours,

Language , Password, Multi-screen, Date & Time, Panel

Alignment , and Color Uniformity.

Clears the cumulative lamp hours use time. Reset when you replace the lamp.

The name and settings saved in Save Memory are reset.

s

"Memory Function" p.67

103

Troubleshooting

This chapter explains how to identify problems and what to do if a problem is found.

Using the Help

If a problem occurs with the projector, the Help screen is displayed to assist you by pressing the Help button. You can solve problems by answering the questions.

a Press the [Help] button.

The Help screen is displayed.

Remote control c Confirm the selection.

Remote control

105

Questions and solutions are displayed as shown on the screen below.

Press the [Help] button to exit the Help.

b Select a menu item.

a

See the following if the Help function does not provide a solution to the problem.

s

"Problem Solving" p.106

Remote control

Problem Solving

If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.

See the following if the indicators do not show clearly what the problem might be.

s

"When the Indicators Provide No Help" p.110

Reading the Indicators

The projector is provided with the following four indicators that indicate the operating status of the projector.

106

A Power indicator Indicates the operating status.

Standby condition

In this status, you can start projecting by pressing the [ ] button on the remote control, or the [t] button on the control panel.

Preparing for network monitoring or cool down in progress

All buttons are disabled while the indicator is flashing.

Problem Solving

107

B Lamp indicator

C Temp indicator

D Filter indicator

Warming up

Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.

The [t] button is disabled during warm-up.

Projecting

Indicates the projection lamp status.

Indicates the internal temperature status.

Indicates the air filter status.

Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.

If all indicators are off, check that the power cord is connected correctly and that the power is being supplied normally.

Sometimes, when the power cord is unplugged, the [ t

] indicator remains lit for a short period, but this is not a fault.

Status Cause

Internal Error

: Lit : Flashing : Off : Varies according to the projector status

Remedy or Status

Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the

Epson Projector Contact List.


Fan Error

Sensor Error




High Temp Error

(Overheating)

The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector switches to standby mode, so check the following two points.

• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.

• If the air filter is clogged, clean or replace it.

s


s


If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Problem Solving

108

Status Cause

Lamp Error

Lamp Failure

Auto Iris Error

Power Err. (Ballast)

Remedy or Status

When using at an altitude of 1500 m or more, set High Altitude Mode to On.

s

"Extended Menu" p.86

Check the following two points.

• Take out the lamp and check if it is cracked.

s


• Clean the air filter.

s


If the lamp is not cracked : Reinstall the lamp and turn on the power.

If the error continues : Replace the lamp with a new one and then turn on the power.

If the error continues : Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


If the lamp is cracked : Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be projected until the lamp is replaced.) s Epson Projector Contact List

When using at an altitude of 1500 m or more, set High Altitude Mode to On.

s

"Extended Menu" p.86




Filter Airflow Error Check the following two points.



s


s




Problem Solving

109

Status Cause

High Temp Warning

Replace Lamp

Low Air Flow

Air Filter Notice

Remedy or Status

(This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)



s


s


Replace it with a new lamp.

s


If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. Replace it with a new lamp as soon as possible.

Check the following two points.



s


s




"Time to clean the air filter. Clean or replace the air filter."is displayed. Clean the air filter.

s


The indicators or messages regarding Air Filter Notice are displayed only when Air Filter Notice is set to On from the Configuration menu.

s Extended - Display - Air Filter Notice

p.86

a • See the following if the projector is not operating properly, even though the indicators are all showing normal.

s

"When the Indicators Provide No Help" p.110

• If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Problem Solving

When the Indicators Provide No Help

If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem.

Problems Relating to Images

• No images appear

Projection does not start, the projection area is completely black, or the projection area is completely blue.

• Moving images are not displayed

Videos played back on a computer are black or no image is projected, or the video is not played back on the computer.

• Projection stops automatically

• The message "Not supported" is displayed

• The message "No Signal" is displayed

• Images are fuzzy, out of focus, or distorted

• Interference or distortion appear in images

• The image is truncated (large) or small, the aspect ratio is not suitable, or the image has been reversed

Only part of the image is displayed, the height and width ratios of the image are not correct, or the image may appear reversed from top to bottom or left to right.

• Image colors are not right

The whole image appears purplish or greenish, images are black

& white, or colors appear dull.

• Images appear dark s

p.111

s

p.111

s s s s s s

p.112

p.112

p.112

p.113

p.113

p.114

s

p.115

s

p.116

Problems when projection starts

• The projector does not turn on

Other Problems

• No sound can be heard or the sound is faint s

p.116

s

p.117

• The remote control does not work

• Nothing appears on the external monitor

• I want to change the language for messages and menus

• The authentication setting of wireless LAN fails

• Email is not received even if a problem occurs in the projector

• "The battery that saves your clock settings is running low." is displayed

• Cannot change settings using a Web browser s

p.118

s

p.119

s

p.119

s

p.120

s

p.120

s

p.120

s

p.121

110

Problem Solving

111

Problems Relating to Images

No images appear

Check

Did you press the [ ] button on the remote control or the [t] button on the control panel?

Are the indicators switched off?

Press the [

Remedy

] button on the remote control or the [t] button on the control panel to turn on the projector.

Is A/V Mute active?

Are the Configuration menu settings correct?

Is the image to be projected completely black?

(Only when projecting computer images)

Is the image signal format setting correct?

(Only when projecting images from a video source)

Is Windows Media Center displayed in full screen?

(Only during network connection)

Is an application using the Windows DirectX function displayed?

(Only during network connection)

The power cord is not connected correctly or power is not being supplied.

Connect the projector's power cord correctly.

Check that your electrical outlet or power source is functioning correctly.

Press the [A/V Mute] button to release A/V Mute.

s


Reset all of the settings.

s Reset - Reset All

p.103

Some input images, such as screen savers, may be completely black.

Change the setting according to the signal for the connected equipment.

s Signal - Video Signal

p.82

When Windows Media Center is displayed at full screen, you cannot project using a network connection. Reduce the screen size.

Applications using the Windows DirectX function may not display images correctly.

Moving images are not displayed

Check

Is the computer's image signal being output to the LCD and the monitor?

(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)

Remedy

Change the image signal from the computer to external output only. Check your computer's documentation, or contact the computer's manufacturer.

Problem Solving

112

Check

Are the contents of the moving image you are trying to project copyright protected?

Remedy

The projector may not be able to project copyright protected moving images that are being played back on a computer.

For more details, see the user's guide supplied with the player.

Projection stops automatically

Check

Is Sleep Mode set to On?

Remedy

Press the [ ] button on the remote control or the [t] button on the control panel to turn on the projector. If you do not want to use Sleep Mode, change the setting to Off.

s

Extended - Operation - Sleep Mode p.86

The message "Not supported" is displayed

Check



Do the image signal resolution and the refresh rate correspond to the mode?


Remedy



p.82

Refer to the computer's documentation for how to change the image signal resolution and the refresh rate output from the computer.

s

"Supported Monitor Displays" p.169

The message "No Signal" is displayed

Check

Are the cables connected correctly?

Is the correct port selected?

Is the power for the computer or video source turned on?

Remedy

Check that all the cables required for projection are securely connected.

Check that no cables are disconnected and that there are no poor contacts in the cables.

Press the [Search] button or the [Source Search] button to change the image.

s

"Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.41

Turn the power on for the equipment.

Problem Solving

113

Check

Are the image signals being output to the projector?

(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)

Remedy

If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to change the output to an external destination as well as the computer's own monitor. For some computer models, when the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.

If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn the power for the computer and the projector off and then back on again.

s Computer's documentation

Images are fuzzy, out of focus, or distorted

Check

Is the focus adjusted correctly?

Is the projector at the correct distance?

Has condensation formed on the lens?

Are you using the optional short throw zoom lens (ELPLU01)?

Remedy

Turn the focus ring to adjust the focus.

s


Is it projecting outside of the recommended projection distance range?

Setup within the recommended range.

s

"Screen Size and Projection Distance" p.158

If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and wait for the condensation to disappear.

Set the Lens Type to ELPLU01 from the configuration menu.

s Extended - Operation - Lens Type

p.86

See the following for more information on focus correction methods.

s

"When using the short throw zoom lens ELPLU01" p.26

Interference or distortion appear in images

Check



Remedy



p.82

Problem Solving

114

Check


Is an extension cable being used?

Is the correct resolution selected?


Are the Sync.

g and Tracking g

settings adjusted correctly?


Is the Resolution set to anything other than Auto?

(Only when projecting on a split screen)

Remedy


s


If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to check if the cables you are using may be causing the problem.

Set the computer so that the signals being output are compatible with the projector.

s



Press the [Auto] button on the remote control or the [ ] button on the control panel to perform automatic adjustment.

If the images are not adjusted correctly even after performing automatic adjustment, you can also make adjustments from the Configuration menu.

s

Signal - Tracking, Sync. p.82

The image may be collapsed if the Resolution on the Configuration menu and the resolution of the projected image are not the same.

If the image is collapsed, set the Resolution to Auto.


p.82

The image is truncated (large) or small, the aspect is not suitable, or the image has been reversed

Check

Have the Screen been set correctly?

Is the aspect adjusted correctly?

Is a wide panel computer image being projected?


Is the image still being enlarged by E-Zoom?

Is Scale set to On?

Remedy

Make the appropriate Screen for the screen being used.

s


Press [Aspect] button, and then select the aspect according to the input signal.

s




p.82

Press the [Esc] button on the remote control to cancel E-Zoom.

s


Set Scale to Off on the configuration menu.

s

Signal - Scale p.82

Problem Solving

115

Check

Is the image position adjusted correctly?

Is the computer set for dual display?


Is the correct resolution selected?


Is the image direction correct?

Remedy

(Only when projecting analog RGB signals input from the Computer port)

Press the [Auto] button on the remote control or the [ ] button on the control panel to adjust the position.

You can also adjust the position from the Configuration menu.

s Signal - Position

p.82

If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.

s Computer video driver documentation

Set the computer so that the signals being output are compatible with the projector.

s



Make the correct settings in Projection from the Configuration menu.

s

"Installation Requirements" p.20

Image colors are not right

Check

Do the input signal settings match the signals from the connected device?

Is the image brightness adjusted correctly?


Is the contrast g adjusted correctly?

Remedy

Change the following settings according to the signal for the connected equipment.

• When the image is from a device connected to the Computer port or the BNC port s Signal - Input Signal

p.82

• When the image is from a device connected to the Video port or the S-Video port s Signal - Video Signal

p.82

Adjust the Brightness setting from the Configuration menu.

s

Image - Brightness p.81


Check that no cables are disconnected and that there are no poor contacts in the cables.

s


Adjust the Contrast setting from the Configuration menu.

s Image - Contrast

p.81

Problem Solving

116

Check

Is the color adjustment set correctly?

Are the color saturation and tint adjusted correctly?


Images appear dark

Check

Is the image brightness set correctly?

Is the contrast g adjusted correctly?

Is it time to replace the lamp?

Is only one projector being used?

Remedy

Adjust the Gamma, RGB, or RGBCMY setting from the Configuration menu.

s Image - Advanced

p.81

s

"Adjusting the Image" p.49

Adjust the Color Saturation and Tint settings from the Configuration menu.

s Image - Color Saturation, Tint

p.81

Remedy

Check the Brightness and Power Consumption settings from the Configuration menu.

s

Image - Brightness p.81

s Settings - Power Consumption

p.84

Adjust the Contrast setting from the Configuration menu.

s Image - Contrast

p.81

When the lamp is nearly ready for replacement, the images become darker and the color quality becomes poorer. When this happens, replace the lamp with a new lamp.

s


Check if the following items are set to dark.

s Extended - Multi-Projection - Brightness Level

p.86

s Extended - Multi-Projection - Multi-screen

p.86

Problems when Projection Starts

The projector does not turn on

Check

Did you press the [ ] button on the remote control or the [t] button on the control panel?

Remedy

Press the [ ] button on the remote control or the [t] button on the control panel to turn on the projector.

Problem Solving

117

Check

Are the indicators switched off?

Remedy

The power cord is not connected correctly or power is not being supplied.

Disconnect and then reconnect the power cord.


Do the indicators turn on and off when the power cord is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Is the Control Panel Lock set to Full Lock?

Press the [ ] button on the remote control. If you do not want to use Control Panel Lock, change the setting to

Off .

s

"Control Panel Lock" p.74

Is the correct setting for the remote receiver selected?

Was the power cable plugged back in or was the breaker turned on immediately after Direct Power Off?

Check the Remote Receiver from the Configuration menu.


p.84

When the operation to the left is performed when Direct Power On is set to On, the power may not turn back on. Press the [ ] button on the remote control or the [t] button on the control panel to turn on the projector.

Is the [ID] switch on the remote control set to On?

Are the lamp cover and lamps installed correctly?

When the switch is set to On, you can use the remote control to operate only a projector with a matching ID. Set the [ID] switch to Off.

s

"Setting the remote control ID" p.29

If the lamp or lamp cover is installed incorrectly, the projector cannot be turned on. Check how it is installed.

s

"How to replace the lamp" p.129

Other Problems

No sound can be heard or the sound is faint

Check

Check that the audio/video cable is securely attached to both the projector and audio source.

Remedy

Disconnect the cable from the Audio port, and then reconnect the cable.

Problem Solving

118

Check

Is the projector volume set to the minimum?

Is the volume for the computer or from the image source set to the minimum?

Is A/V Mute active?

Adjust the volume so that sound can be heard.

s

Settings - Volume p.84

s

"Adjusting the Volume" p.42

Adjust the volume so that sound can be heard.

Is the audio cable's specification "No resistance"?

Is it connected with an HDMI cable?

Is the correct audio input selected?

Remedy

Press the [A/V Mute] button to release A/V Mute.

s


When using a commercially available audio cable, make sure it is labeled "No resistance".

If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.

Check the Audio Settings from the configuration menu.


p.86

The remote control does not work

Check

Is the remote control light-emitting area pointing towards the remote receiver on the projector during operation?

Point the remote control towards the remote receiver.

s


Remedy

Is the remote control too far from the projector?

The operating range for the remote control is about 15 m.

s


Set the projector up in a location where strong light does not shine onto the remote receiver.

Is direct sunlight or strong light from fluorescent lamps shining onto the remote receiver?

Is the correct setting for the Remote Receiver selected?

Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary.

s

"Replacing the remote control batteries" p.14

Are the remote control ID and the projector ID matched?

Check the Remote Receiver from the Configuration menu.


p.84

Make sure the ID for the projector you want to operate and the ID for the remote control match. To operate all projectors by remote control regardless of the ID setting, set the [ID] switch on the remote control to Off.

s

"ID Settings" p.28

Problem Solving

119

Check

Does Remote Control Type match the remote control that you are using?

Is the optional remote control cable connected to the projector's

Remote port?

Is Control Communications set to On? (EB-G6750WU only)

Is the remote control button lock set?

Remedy

Check the Remote Control Type on the configuration menu.

s Extended - Operation - Remote Control Type

p.86

When the remote control cable is connected, the projector's remote receiver is disabled. When not using the remote control cable set, disconnect it from the Remote port.

The Remote port is disabled. When using the optional remote control cable set, set Control Communications to

Off .

s

Extended - HDBaseT - Control Communications p.86

When the remote control button lock is set, buttons except for those needed for basic remote control operations are deactivated. Hold down the [Help] button to cancel the remote control button lock.

s

"Remote control button lock" p.75

Nothing appears on the external monitor

Check

Are images input from a port other than the Computer port or

BNC port?

Are you projecting a split screen?

Remedy

Only RGB signals from the Computer port or the BNC port can be displayed on an external monitor.

Is the projector in standby status?

Only RGB signals projected on the left screen from the Computer port or the BNC port can be displayed on an external monitor.

s

"Projecting Two Images Simultaneously (Split Screen) " p.60

Check that Standby Mode, A/V Output, and Monitor Out from the Configuration menu are set correctly.


p.86

s Extended - A/V Settings

p.86

I want to change the language for messages and menus

Check

Change the Language setting.

Remedy

Adjust the Language setting from the Configuration menu.

s Extended - Language

p.86

Problem Solving

120

The authentication setting of wireless LAN fails

Check

Is the time set correctly?

Remedy

If the wireless LAN is set correctly but the authentication setting fails, the time may not be set correctly. Check if it is set correctly.

s


Email is not received even if a problem occurs in the projector

Check

Is Standby Mode set to Communication On?

Did a fatal abnormality occur and the projector come to a sudden stop?

Is power being supplied to the projector?

Is the Mail Notification function set correctly in the Configuration menu?

Remedy

To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from the Configuration menu.


p.86

When the projector comes to a sudden stop, email cannot be sent.

If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson Projector Contact

List.



An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.

s

"Administrator Settings menu" p.98

"The battery that saves your clock settings is running low." is displayed

Check

The internal power supply that saves your clock settings is running low.

Remedy

Contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Problem Solving

121

Cannot change settings using a Web browser

Check

Are the user ID and password correct?

Remedy

Enter "EPSONWEB" as the user ID. This cannot be changed. Enter the user ID even if the password setting is disabled.

Enter the characters set for the Web Control Password as the password. The default password is "admin".

About Event ID

122

Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Event ID

0432

0435

0434

0481

0482

0485

0433

0484

04FE

04FF

0891

0892

0893

0894

0898

Cause

Failed to startup EasyMP Network Projection.

Network communication is unstable.

Cannot play transferred images.

Communication was disconnected from the computer.

EasyMP Network Projection ended unexpectedly.

A system error occurred in the projector.

Cannot find an access point with the same SSID.

The WPA/WPA2 authentication type does not match.

The WEP/TKIP/AES encryption type does not match.

Communication was disconnected because the projector connected to an unauthorized access point.

Failed to acquire DHCP.

Restart the projector.

Remedy

Check the network communication status, and reconnect after waiting for a while.

Restart EasyMP Network Projection.

Check the status of network communications. Restart the projector.

Restart the projector.

Set the computer, the access point, and the projector to the same SSID.

Check that the wireless LAN security settings are correct.

s

"Security menu " p.94

Contact your network administrator for more information.

0899

089A

089B

089C

Other communication errors

The EAP authentication type is not the same.

EAP server authentication failed.

EAP client authentication failed.

Check the DHCP server to see if it is operating correctly and check the LAN cable to see if it is connected correctly. If you are not using DHCP, turn off the

DHCP setting.

s

"Network Menu" p.89

If restarting the projector or EasyMP Network Projection does not solve the problem, contact your local dealer or the nearest address provided in the Epson

Projector Contact List.


Check that the wireless LAN security settings are correct. Also, check if the certificate is installed correctly.

s

"Security menu " p.94

About Event ID

Event ID

089D Key exchange failed.

Cause Remedy

123

Maintenance

This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.

Cleaning

125

You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.

Caution

When cleaning, unplug the power cable from the electric outlet. Otherwise, it could cause an electric shock.

Cleaning the Lens

Use a commercially available cloth for cleaning glasses to gently wipe the lens.

Warning

Do not use sprays that contain flammable gas to remove dust and lint from the lens. The projector may catch fire due to the high internal temperature of the lamp.

Attention

Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged.

Cleaning the Projector's Surface

Clean the projector's surface by wiping it gently with a soft cloth.

If the projector is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and then firmly wring the cloth dry before using it to wipe the projector's surface.

Attention

Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality of the case may change or become discolored.

Cleaning the Air Filter

When the following message is displayed and the filter indicator flashes green, clean the air filter and the air intake vent.

"Time to clean the air filter. Clean or replace the air filter."

"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter."

"The air filter is clogged. Clean or replace the air filter."

Attention

• If dust collects on the air filter, it can cause the internal temperature of the projector to rise, and this can lead to problems with operation and shorten the optical engine's service life. Clean the air filter immediately when the message is displayed.

• Do not rinse the air filter in water. Do not use detergents or solvents.

• When using a brush for cleaning, use one with long soft bristles, and brush it lightly. If it is brushed too strongly, dust will be ground into the air filter and cannot be removed.

Cleaning the air filter

The air filter can be replaced even when the projector is suspended from a ceiling.

a After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cable.

Cleaning b Open the air filter cover.


126 d With the front (the side with tabs) of the air filter facing down, tap the air filter four or five times to shake off the dust.

Turn it over and tap the other side in the same way.

c Remove the air filter.

Grip the tab in the center of the air filter, and pull it straight out.

Attention

If the air filter is hit too hard, it may become unusable due to deformities and cracks.

e Remove any dust remaining on the air filter by using a vacuum cleaner from the front side.

Cleaning f Replace the air filter.

Press until it clicks into place.

g Close the air filter cover.

a • If a message is frequently displayed, even after cleaning, it is time to replace the air filter. Replace it with a new air filter.

s


• It is recommended that you clean these parts at least once every three months. Clean them more often than this if using the projector in a particularly dusty environment.

• The indicators or messages regarding Air Filter Notice are displayed only when Air Filter Notice is set to On from the Configuration menu.

s Extended - Display - Air Filter Notice

p.86

127

Replacing Consumables

This section explains how to replace the lamp and the air filter.

Replacing the Lamp

Lamp replacement period

It is time to replace the lamp when:

• The following message is displayed.

"It is time to replace your lamp. Please contact your Epson projector reseller or visit www.epson.com to purchase."

The message is displayed for 30 seconds.

• The lamp indicator flashes orange.

128

Attention

• The lamp replacement message is set to appear after the following time periods in order to maintain the initial brightness and quality of the projected images.

For EB-G6750WU/EB-G6650WU/EB-G6350/EB-G6250W

When using Power Consumption continually at Normal: About 1900 hours

When using Power Consumption continually at ECO: About 3900 hours

For EB-G6550WU/EB-G6150


When using Power Consumption continually at ECO: About 3900 hours

For EB-G6450WU/EB-G6050W


When using Power Consumption continually at ECO: About 3900 hours s Settings - Power Consumption

p.84

• If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. When the lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working.

• Do not repeatedly turn off the power and immediately back on. Turning the power on and off frequently may shorten the lamp's operating life.

• Depending on the characteristics of the lamp and the way it has been used, the lamp may become darker or stop working before the lamp warning message appears. You should always have a spare lamp unit ready in case it is needed.

• We recommend the use of genuine EPSON spare lamps. The use of nongenuine lamps may affect projection quality and safety. Any damage or malfunction caused by the use of non-genuine lamps may not covered by

Epson's warranty.

• The projected image gets darker or starts to deteriorate.

Replacing Consumables a • We recommend that you clean the air filter whenever you replace the lamp.

s


• Replace the air filter if it is discolored or if a message appears even after cleaning the air filter.

s


How to replace the lamp

The lamp can be replaced even when the projector is suspended from a ceiling.

Warning

• When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is cracked, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Be careful when removing the lamp cover as shards of glass may fall out and could cause an injury. If any shards of glass get into your eyes or mouth, contact your local physician immediately.

• Never disassemble or remodel the lamp. If a modified or disassembled lamp is installed in the projector and used, it could cause a fire, electric shock, or an accident.

Caution

Wait until the lamp has cooled down sufficiently before removing the lamp cover. If the lamp is still hot, burns or other injuries may result. It takes about one hour after the power has been turned off for the lamp to be cool enough.

a After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cord.

129 b Wait until the lamp has cooled down, then remove the projector's lamp cover.

Loosen the Lamp cover fixing screw with the screwdriver supplied with the new lamp unit or a cross-head screwdriver, and then remove the lamp cover. Because there is a string attached to the lamp cover to prevent it from falling, you can replace the lamp even when the projector is installed on a ceiling without the lamp cover falling down.

c Loosen the two lamp fixing screws.

Replacing Consumables d Take out the old Lamp by pulling the handle.

If the Lamp is cracked, replace it with a new lamp, or contact your local dealer for further advice.

s Epson Projector Contact List f Tighten the two lamp fixing screws.

130 e Install the new lamp.

Insert the lamp along the guide rail in the correct direction so that it fits in place and press it firmly to the back.

g Replace the lamp cover.

Replacing Consumables

Attention

• Make sure you install the lamp securely. If the lamp cover is removed, the power turns off automatically as a safety precaution. If the lamp or the lamp cover is not installed correctly, the power does not turn on.

• This product includes a lamp component that contains mercury (Hg). Please consult your local regulations regarding disposal or recycling. Do not dispose of it with normal waste.

Resetting the lamp hours

The projector records how long the lamp is turned on and a message and indicator notify you when it is time to replace the lamp. After replacing the lamp, make sure you reset the Lamp Hours from the Configuration menu.

s

"Reset Menu" p.103

a

Only reset the Lamp Hours after the lamp has been replaced.

Otherwise the lamp replacement period is not indicated correctly.

Replacing the Air Filter

Air filter replacement period

If the message is displayed frequently even though the air filter has been cleaned, replace the air filter.

How to replace the air filter

The air filter can be replaced even when the projector is suspended from a ceiling.

a After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cord.

b Open the air filter cover.


131 c Remove the air filter.

Grip the tab in the center of the air filter, and pull it straight out.

Replacing Consumables d Install the new air filter.

Press until it clicks into place.

e Close the air filter cover.

a

Dispose of used air filters properly in accordance with your local regulations.

Material of the frame part: Polypropylene

Material of the filter part: Polypropylene

132

Notes on Transportation

133

There are many glass parts and precision components inside the projector.

To prevent damage due to impacts when transporting, handle the projector as follows.

• Fit the protective lens pad that was used at the time of purchase.

Notes when packing and transporting

Enclose the projector securely in buffer material to protect it from shock, and place it into a strong cardboard container. Be sure to notify the carrier company that the contents are fragile.

Moving Nearby

Check the following points, and move the projector carefully.

• Turn off the power to the projector and disconnect all cables.

• Attach the cover to the lens.

Caution

Do not carry the projector by one person.

Two people are needed to unpack or carry the projector.

When Transporting

Preparing packaging

After checking the points in "Moving Nearby", prepare the following and then pack up the projector.

• Remove the lens unit if an option lens, other than the standard zoom lens, is installed. Attach the standard zoom lens if the projector has a built-in lens. If the projector does not have a lens, attach the cover that was on the lens mount when you purchased the projector.

• Set the vertical lens shift to the lowest position.

s

"Adjusting the Position of the Projected Image (Lens Shift)" p.24

Image Maintenance

134

Panel Alignment

Adjusts the pixel color shift for the LCD panel. You can adjust the pixels horizontally and vertically by 0.25 pixels within a range of ±1 pixel.

a • Image quality may decline after performing LCD alignment.

• Images for pixels that extend beyond the edge of the projected screen are not displayed.

a b c



Select Panel Alignment, and then press the [ ] button.

(1) Select Panel Alignment, and then press the [ ] button.



e Select the color you want to adjust.

(1) Select Select Color, and then press the [ ] button.

(2) Select R (red) or B (blue), and then press the [ ] button.


f Select the grid color displayed when making adjustments from

Pattern Color.

(1) Select Pattern Color, and then press the [ ] button.

d Enable Panel Alignment.


135

(2) Select a combination of R (red), G (green), and B (blue) for the grid color.

R/G/B : Displays a combination all three colors; red, green and blue. The actual color of the grid is white.

R/G : This is available when R is selected from Select Color. Displays a combination of two colors; red and green. The actual color of the grid is yellow.

G/B : This is available when B is selected from Select Color. Displays a combination of two colors; green and blue. The actual color of the grid is cyan.


g Select Start Adjustments, and then press the [ ] button. When the message is displayed, press the [ ] button again.

Adjustment starts. All four corners are adjusted in order starting at the top left.

a

The image may become distorted while adjusting. The image is restored once adjustments are complete.

h Use the [ ], [ ], [ ], and [ ] buttons to make adjustments, and then press the [ ] button to move to the next adjustment point.

i When you have adjusted all four corners, select Exit, and then press the [ ] button.

If you feel you still need to make adjustments after correcting all four points, select Select intersection and adjust and then continue making adjustments.

Color Uniformity

Adjusts the color tone for the whole screen.

a

The color tone may not be uniform even after performing color uniformity.

a b c



Select Color Uniformity, and then press the [ ] button.



136 h Use the [ ], [ ], [ ], and [ ] buttons to select the area you want to adjust, and then press the [ ] button.

If you select the center, the whole screen is adjusted. Adjust the outer areas first, and then adjust the whole screen.

Adjustment Level : There are five levels from white, through gray, and up to black. You can adjust each level individually.

Start Adjustments : Starts making color uniformity adjustments.

Reset : Resets all adjustments and settings for Color Uniformity to their default values.

a

The image may become distorted while adjusting Color

Uniformity . The image is restored once adjustments are complete.

d e f g

Select Adjustment Level, and then press the [ ] button.

Use the [ ][ ] buttons to set the adjustment level.


Select Start Adjustments, and then press the [ ] button.

i Use the [ ][ ] buttons to select the color you want to adjust, and then use the [ ][ ] buttons to adjust.

Press the [ ] button to weaken the color tone. Press the [ ] button to strengthen the color tone.

j Return to step 4 and adjust each level.

Image Maintenance k When you are done, press the [Menu] button.

Adjusting the Lens Balance

The lens may tilt depending on the projector's installation angle or the weight of the lens unit that is attached. If the lens is tilted, images may be out of focus. Adjust the lens balance if some areas of the projected image are out of focus.

Special techniques are necessary to adjust the lens balance. Contact your local dealer or the nearest address provided in the Epson Projector Contact

List.

Warning

When adjusting the lens balance, make sure you follow the steps in this User's

Guide to prevent light from the projector from shining into your eyes. If you do not follow the steps correctly, the bright light can damage your eyes.

a b

Turn off the projector if it is on.

Remove the projector lens unit.

s

"Removing" p.17

c Press a screwdriver and so on down into the clip on the lens installation section (on the opposite side of the lens shift dial), and then remove the cover.

The illustration shows the projector mounted on a ceiling.

137 d Remove the inner cap by pushing the two clips on the inner cap in the direction shown by the arrows.

e Use a cross-head screwdriver #1 to remove the fixing screws (four points).


138

Attention

Keep the screws in a safe place as you will need these when transporting the projector.

f Loosen the locking screws (three points) by 1/4 of a turn (45˚) with a ball point hexagonal wrench.

a

Use the following pattern to adjust the lens balance.

45 j Adjust the focus with the focus ring.

s


Check the areas that are out of focus on the projection screen.

k l

Press the [A/V Mute] button to temporarily hide the images.

Insert the ball point hexagonal wrench into the adjustment screw holes. Cover the lens with your hand so that you cannot look directly into it.

Attention

Do not rotate the locking screw more than 1/4 of a turn (45˚). This may cause malfunctions to occur.

g Attach the projector lens unit.

s

"Attaching" p.16

h Turn on the projector in a position that prevents you from looking directly into the lens.

i Press the [Test Pattern] button on the remote control or the [ ] button on the control panel to display the test pattern.

Press the [ ][ ] buttons on the remote control or the [ ] button on the control panel to change the test pattern.

m Move around to the back of the projector so that the light cannot shine into your eyes, and then press the [A/V Mute] button to release A/V Mute.

Image Maintenance n Press the [Test Pattern] button on the remote control or the [ ] button on the control panel to display the test pattern.

o Adjust the lens balance by turning the adjustment screws with the ball point hexagonal wrench.

139

A Loosen

B Tighten

When the screws are loosened the focus moves to the rear, and when the screws are tightened the focus is brought to the front.

The following illustration shows the adjustment screws and their relative adjustment positions when viewed from the rear of the projector.

p Repeat steps 11 to 15 to make further adjustments.

Whenever you make adjustments, adjust the focus with the focus ring and check the projected image.

q When you have finished making adjustments, turn off the projector and remove the projection lens unit.

r Tighten the locking screws (three points).

Image Maintenance s See step 4 to attach the inner cap, and then see step 3 to attach the cover.

t Attach the projector lens unit.

Attention

When performing the following operations, attach the fixing screws, and then tighten all screws to their initial positions.

• When transporting

• When readjusting the lens balance

If the screws are not tightened to their initial positions, a malfunction could occur.

140

Appendix

Network Functions

142

This chapter explains the additional functions for networks.

Projecting with "Connect to a Network Projector"

The projector supports the Windows "Connect to a Network Projector" function. For more information about the "Connect to a Network Projector" function, see the documentation supplied with your computer or the

Microsoft's Web site.

a • Make sure the computer and projector are ready to connect to the network.

• When using "Connect to a Network Projector", change the projector's source to LAN.

• When the projector password screen is displayed, enter the keyword shown at the bottom of the LAN standby screen.

• You can connect only one projector to a computer.

• When using Network Projector from Options in Windows Meeting

Space, set the colors for the computer screen you are using to the highest level (32bit). If it is not capable of a 32bit display, a message is displayed and you cannot connect.

• PIN Code Method

SSID and security are set automatically by inputting an 8-digit code that was assigned to the projector from the computer to the access point in advance. Make connection settings between the computer and the access point in advance. For details on how to make this connection, refer to the manual provided with the access point. This method is recommended when the projector is mounted on the ceiling.

a

Refer to the documentation for the access point device and to the following section when using any connection method other than WPS.

s

"Wireless LAN menu" p.92

Connection Setup Method a Press the [Menu] button.

s


b Select Network Configuration from Network.

Making a WPS (Wi-Fi Protected Setup) Connection with a Wireless LAN Access Point

There are two methods for setting WPS g

.

• Push Button Method

SSID and security are set automatically when the [ ] button is pressed on the projector's control panel and the dedicated button on the access point equipment. This method is recommended when the projector and access point are close together.

The Network Configuration screen is displayed.

c From Wireless LAN select To Setup Wizard.

Network Functions

143

• The wireless LAN unit (ELPAP07) is connected to the projector.

• The projector is setup to connect to the network using wireless LAN.

s

"Wireless LAN menu" p.92

a Turn on the projector, and then press the [LAN] button on the remote control.



Follow the on-screen instructions.

Using the Quick Wireless Connection USB Key

Connect the optional Quick Wireless Connection USB Key to the wireless

LAN unit installation section. Check the following points when connecting a computer to the projector using wireless LAN.

b Check that the SSID and IP address information are displayed, and then remove the wireless LAN unit.

s

"Installing the Wireless LAN Unit" p.38

c Insert the Quick Wireless Connection USB Key in the wireless LAN unit installation section.

Network Functions d When the message "Network information update complete.

Remove the Quick Wireless Connection USB Key Adapter." is displayed, remove the Quick Wireless Connection USB Key.

After removing the Quick Wireless Connection USB Key, reattach the wireless LAN unit.

e Connect the Quick Wireless Connection USB Key to the computer.

From this point on, see the user's guide supplied with the Quick

Wireless Connection USB Key.

144

Monitoring and Controlling

145

About EasyMP Monitor

EasyMP Monitor lets you carry out operations such as checking the status of multiple Epson projectors that are connected to a network at a computer monitor, and controlling the projectors from the computer.

You can download EasyMP Monitor from the following Web site.


a

If you set Standby Mode to Communication On, you can use the

Web browser to make settings and perform control even if the projector is in standby mode (when the power is off).


p.86

Projector setup

In the Web browser, you can set items that are usually set in the projector's

Configuration menu. The settings are reflected in the Configuration menu.

About Message Broadcasting

Message Broadcasting is plugin software for EasyMP Monitor.

Message Broadcasting can be used to send a message (JPEG file) to project on all Epson projectors or specified projectors connected on the network.

The data can be sent manually, or sent automatically using Timer Settings of EasyMP Monitor.

Download the Message Broadcasting software from the following website.


Items in the Configuration menu that cannot be set by the Web browser

• Settings Menu - User Button

• Extended Menu - Display - Menu Position, Panel Alignment, Color

Uniformity

• Extended Menu - User's Logo

• Extended Menu - Operation - High Altitude Mode, BNC Sync

Termination

• Extended Menu - Language

• Reset Menu

The settings for items on each menu are the same as the projector's

Configuration menu.

s

"Configuration Menu" p.77

Changing Settings Using a Web Browser (Web

Control)

By using the Web browser of a computer connected to the projector on a network, you can make settings and control the projector. This function allows you to perform setup and control operations remotely. In addition, since you can use the computer's keyboard, entering characters required for the setup is easier.

Use Internet Explorer 8.0 or later as the Web browser. If using a Mac OS

X, use Safari.

Displaying the Web Control screen

Use the following procedure to display the Web Control screen.

Make sure the computer and projector are connected to the network.

Set Connection Mode to Advanced from the Configuration menu.

s

Network - Wireless LAN - Connection Mode

p.92

Monitoring and Controlling a

If your Web browser is set up to connect via a proxy server, the Web

Control screen cannot be displayed. To display Web Control, you need to make settings so that a proxy server is not used for a connection.

a b

Start the Web browser on the computer.

Enter the IP address of the projector in the address input box of the Web browser, and press the Enter key on the computer's keyboard.

The Web Control screen is displayed.

When Web Control Password is set in the Network menu from the projector's Configuration menu, the password entry screen is displayed.

c The user ID and password entry screen is displayed.

Enter "EPSONWEB" as the user ID.

The default password is "admin".

a • Enter the user ID even if the password setting is disabled.

You cannot change the user ID.

• You can change the password in the Network menu from the

Configuration menu.

s Network - Administrator Settings - Web Control

Password

p.98

Setting Certificates

You can use a Web browser to set the certificate settings used for wireless

LAN authentication.

Install the following certificates in the projector: Client Certificate and CA certificate for wireless LAN security settings, and Web Server Certificate for the Secure HTTP function.

a Display Web Control.

s

"Displaying the Web Control screen" p.145

b Click Administrator Settings - Manage Certificates from

Network.

c The Manage Certificates screen appears.

Submenu Name

Client Certificate

CA certificate

Self-signed Certificate


Refresh/Clear

Issued to

Issued by

Validity period

Refresh/Clear

Issued to

Issued by

Validity period

Refresh/Clear

Issued to

Issued by

Validity period

Web Server Certificate Refresh/Clear

Issued to

Issued by

Validity period

146

Monitoring and Controlling a

When installing a certificate, make sure the projector supports its format.

s

"List of supported certificates" p.147

Password

Item Explanation

Required. Up to 32 alphanumeric characters

Secure HTTP Notes

When Secure HTTP in Administrator Settings from the Network menu is set to On, security using HTTPS protocol is automatically applied. You can use this function to increase security between the projector and a Web browser.

A certificate is used in communication using HTTPS protocol to certify reliability of the server. Create a server certificate to verify reliability from a

Web browser, and install it on the projector.

If there is no server certificate, the projector automatically creates a selfsigned certificate and communicates. Because this self-signed certificate cannot verify reliability from a Web browser, a warning about the server's reliability is generated when the projector is accessed from a Web browser.

Although the security level is decreased when compared to a server certificate, you can continue to communicate by ignoring the warning.

List of supported certificates

Client Certificate (PEAP-TLS/EAP-TLS)

Extension

Hashes

Item

Supported format

Encryption

Key length

Explanation

PKCS#12

PKCS, P12

RSA

MD5/SHA-1/SHA-256/SHA-384/SHA-512

512/1024/2048/4096 bit

Server Certificate (PEAP/PEAP-TLS/EAP-TLS/EAP-Fast)

Key length

Encode

Item

Supported format

Extension

Encryption

Hashes

Explanation

X509v3

DER/CER/PEM

RSA


512/1024/2048/4096 bit

BASE64/Binary

Web Server Certificate (Secure HTTP)

Supported format

Extension

Encryption

Hashes

Key length

Common Name

Organization

Password

Item Explanation

PKCS#12

PKCS, P12

RSA


512/1024/2048/4096 bit

Network host name

Optional

Required. Up to 32 alphanumeric characters

147


148

Using the Mail Notification Function to Report

Problems

When you set Mail Notification, notification messages are sent to the preset email addresses when a problem or warning occurs with a projector. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.

s Network - Administrator Settings - Mail Notification

p.98

a • Up to a maximum of three notification destinations (addresses) can be registered, and notification messages can be sent to all three destinations at once.

• If a projector develops a critical problem and suddenly stops working, it may not be able to send a message notifying an operator of the problem.

• If you set Standby Mode to Communication On, you can control the projector even if it is in standby mode (when the power is off).


p.86

Reading Error Notification Mail

When the Mail Notification function is set to On and a problem or warning occurs in the projector, the following email will be sent.

Mail sender: Address for Address 1

Subject: EPSON Projector

Line 1: The projector name where the problem has occurred

Line 2: The IP address set for the projector where the problem has occurred.

Line 3 and on: Details of the problem

The details of the problem are listed line by line. The main message contents are listed below.

• Clean Air Filter (Air Filter Notice)

• Internal error

• Fan related error

• Sensor error

• Lamp cover is open. (Lamp Cover Open)

• Lamp timer failure

• Lamp out

• Internal temperature error

• High-speed cooling in progress

• Lamp replacement notification

• Low Air Flow (Low Air Flow)

• Low Air Flow Error (Filter Airflow Error)

• No-signal

No Signal is input to the projector. Check the connection status or check that the power for the signal source is turned on.

• Auto Iris Error

• Power Err. (Ballast)

See the following to deal with problems or warnings.

s

"Reading the Indicators" p.106


Management Using SNMP

By setting SNMP to On in the Configuration menu, notification messages are sent to the specified computer when a problem or warning occurs. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.

s Network - Administrator Settings - SNMP

p.98

a • SNMP should be managed by a network administrator or someone who is familiar with the network.

• To use the SNMP function to monitor the projector, you need to install the SNMP manager program on your computer.

• Up to two destination IP addresses can be saved.

Displaying the Web Remote Screen

The Web Remote function allows you to perform projector remote control operations with a Web browser.

a b

Display the Web Control screen.

Click Web Remote.

c The Web Remote screen is displayed.

149

A

[ ] button

Turns the projector on.

B Change input buttons s


C [Freeze] button s


D [A/V Mute] button s


E [Page] buttons s

"Remote Control" p.12

F [Volume] buttons

G [Source Search] button s

"Automatically Detect Input Signals and Change the Projected Image

(Source Search)" p.41

H [t] button

Turns the projector off.


150

ESC/VP21 Commands

You can control the projector from an external device using ESC/VP21.

Command list

When the power ON command is transmitted to the projector, the power turns on and it enters warm-up mode. When the projector's power has turned on, a colon ":" (3Ah) is returned.

When a command is input, the projector executes the command and returns a ":", and then accepts the next command.

If the command being processed terminates abnormally, an error message is output and a ":" is returned.

The main contents are listed below.

Power ON/OFF

Signal selection

Item

On

Off

Computer

BNC

Auto

RGB

Component

Auto

RGB

Component

HDMI

Video

S-Video

LAN

DisplayPort

HDBaseT (EB-G6750WU only)

Command

PWR ON

PWR OFF

SOURCE 1F

SOURCE 11

SOURCE 14

SOURCE BF

SOURCE B1

SOURCE B4

SOURCE 30

SOURCE 41

SOURCE 42

SOURCE 53

SOURCE 70

SOURCE 80

A/V Mute On/Off On

Off

Item Command

MUTE ON

MUTE OFF

Add a Carriage Return (CR) code (0Dh) to the end of each command and transmit.

For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Cable layouts

Serial connection

• Connector shape: D-Sub 9-pin (male)


• Projector input port name: RS-232C

<At the projector>

<At the projector>

Signal Name

GND

TD

RD

Function

Signal wire ground

Transmit data

Receive data

Communications protocol

• Default baud rate setting: 9600 bps

• Data length: 8 bit

• Parity: None

• Stop-bit: 1 bit

• Flow control: None

151

<At the computer>

(PC serial cable) <At the computer>

About PJLink

PJLink Class1 was established by the JBMIA (Japan Business Machine and

Information System Industries Association) as a standard protocol for controlling network-compatible projector's as part of their efforts to standardize projector control protocols.

The projector complies with the PJLink Class1 standard established by the

JBMIA.

You need to make network settings before you can use PJLink. See the following for more information on network settings.

s

"Network Menu" p.89

It complies with all commands except for the following commands defined by PJLink Class1, and agreement was confirmed by the PJLink standard adaptability verification.

URL: http://pjlink.jbmia.or.jp/english/

• Non-compatible commands

Mute settings

Function

Image muting set

Audio muting set

PJLink Command

AVMT 11

AVMT 21

• Input names defined by PJLink and corresponding projector sources

Source PJLink Command

Computer

BNC

Video

S-Video

HDMI

DisplayPort

INPT 11

INPT 13

INPT 21

INPT 22

INPT 32

INPT 35


152

LAN

HDBaseT

Source PJLink Command

INPT 52

INPT 56 (EB-G6750WU only)

• Manufacturer name displayed for "Manufacture name information query"

EPSON

• Model name displayed for "Product name information query"

EPSON 6750

EPSON 6650

EPSON 6550

EPSON 6450

EPSON 6350

EPSON 6250

EPSON 6150

EPSON 6050

• Remote operation using a Web browser

You can operate a projector from your computer just like using a remote control.

• Monitoring and control with application software

You can use Crestron RoomView ® Express or Crestron RoomView ®

Server Edition provided by Creston ® to monitor devices in the system, to communicate with the help desk, and to send emergency messages. See the following Web site for details.

http://www.crestron.com/getroomview

This manual describes how to perform operations on your computer using a Web browser.

a • You can only enter single-byte alphanumeric characters and symbols.

• The following functions cannot be used while using Crestron

RoomView ® .

s


Message Broadcasting (EasyMP Monitor plug-in)

• If you set Standby Mode to Communication On, you can control the projector even if it is in standby mode (when the power is off).


p.86

About Crestron RoomView

®

Crestron RoomView ® is an integrated control system provided by

Crestron ® . It can be used to monitor and control multiple devices connected on a network.

The projector supports the control protocol, and can therefore be used in a system built with Crestron RoomView ® .

Visit the Crestron ® Web site for details on Crestron RoomView ® . (Only

English-language displays are supported.) http://www.crestron.com

The following provides an overview of Crestron RoomView ® .

Operating a projector from your computer

Displaying the operation window

Check the following before carrying out any operations.

• Make sure the computer and projector are connected to the network.

• Set Crestron RoomView to On from the Network menu.

s

Network - Administrator Settings - Crestron RoomView

p.98

Monitoring and Controlling a b

Start the Web browser on the computer.

Enter the IP address of the projector in the address field of the

Web browser, and press the Enter key on the keyboard.

The operation window is displayed.

Using the operation window

A You can perform the following operations when you click the buttons.

Power

Button

Vol-/Vol+

Function

Turns the projector power on or off.

Adjusts the volume.

153

A/V Mute

Freeze

Button

Contrast

Button

Brightness

Color

Sharpness

Zoom

Function


s


Mute)" p.63

B Switch to the image from the selected input source. To display input sources that are not shown in Source List, click (a) or (b) to scroll up or down. The current video signal input source is displayed in blue.

You can change the source name if necessary.

C You can perform the following operations when you click the buttons. To display buttons that are not shown in Source List, click (c) or (d) to scroll left or right.

Function

Images are paused or unpaused.

s


Adjusts the difference between light and shade in the images.

Adjusts the image brightness.

Adjusts the color saturation for the images.

Adjusts the image sharpness.

Click the [z] button to enlarge the image without changing the projection size. Click the [x] button to reduce an image that was enlarged with the [z] button.

Click the [ ], [ ], [ ], or [ ] buttons to change the position of an enlarged image.

s


D

The [ ], [ ], [ ], and [ ] buttons perform the same operations as the [ ],

[ ], [ ], and [ ] buttons on the remote control. You can perform the following operations when you click the other buttons.


OK

Menu

Auto

Search

Esc

Button Function

Performs the same operation as the [ ] button on the remote control.

s



If clicked while projecting analog RGB signals from the

Computer port, you can automatically optimize

Tracking, Sync., and Position.


s



Performs the same operation as the [Esc] button on the remote control.

s


E You can perform the following operations when you click the tabs.

Tab

Contact IT Help

Info

Tools

Function

Displays the Help Desk window. Used to send messages to, and receive messages from, the administrator using

Crestron RoomView ® Express.

Displays information on the projector that is currently connected.

Changes settings in the projector that is currently connected. See the next section.

Using the tools window

The following window is displayed when you click the Tools tab on the operation window. You can use this window to change settings in the projector that is currently connected.

154

A Crestron Control

Make settings for Crestron ® central controllers.

B Projector

The following items can be set.

Item

Projector Name

Location

Assigned To

Function

Enter a name to differentiate the projector that is currently connected from other projectors on the network. (The name can contain up to 15 single-byte alphanumeric characters.)

Enter an installation location name for the projector that is currently connected on the network. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)

Enter a user name for the projector. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)


DHCP

Send

Item

IP Address

Subnet Mask

Default Gateway

Function

Select the Enabled check box to use DHCP. You cannot enter an IP address if DHCP is enabled.

Enter the IP address to assign to the currently connected projector.

Enter a subnet mask for the currently connected projector.

Enter the gateway address for the currently connected projector.

Click this button to confirm the changes made to the

Projector .

C Admin Password

Select the Enabled check box to require a password to open the Tools window.


Item

New Password

Confirm

Send

Function

Enter the new password when changing the password to open the Tools window. (The name can contain up to 26 single-byte alphanumeric characters.)

Enter the same password as you entered in New

Password . If the passwords are not the same, an error is displayed.


Admin Password .

D User Password

Select the Enabled check box to require a password to open the operation window on the computer.


Item

New Password

Confirm

Send

155

Function

Enter the new password when changing the password to open the operation window. (The name can contain up to 26 single-byte alphanumeric characters.)

Enter the same password as you entered in New

Password . If the passwords are not the same, an error is displayed.


User Password .

Optional Accessories and Consumables

The following optional accessories and consumables are available. Please purchase these products as and when needed. The following list of optional accessories and consumables is current as of: January 2013. Details of accessories are subject to change without notice and availability may vary depending on the country of purchase.

Optional Accessories

Standard zoom lens ELPLS06

The lens equipped to models with lenses.

Short throw zoom lens ELPLU01

Rear projection wide lens ELPLR03

Middle throw zoom lens ELPLM04

Middle throw zoom lens ELPLM05

Long throw zoom lens ELPLL06

See the following for more information on the projection distance for each lens.

s

"Screen Size and Projection Distance" p.158

Computer cable ELPKC02

(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)

This is the same as the computer cable supplied with the projector.


(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)


(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)

Use one of these longer cables if the computer cable supplied with the projector is too short.

Component video cable ELPKC19

(3 m - for mini D-Sub 15-pin/RCA male

^

3)

Use to connect a component video g

source.

156

Remote control cable set ELPKC28

(10 m 2 piece set)

Use this to guarantee operation from the remote control from a distance.

Wireless mouse receiver ELPST16

Use this to use the projector's remote control to control the mouse pointer on the computer or to page up and down.

HDBaseT Transmitter ELPHD01 (for EB-G6750WU only)

This transmitter performs long distance transmissions for HDMI signals and

control signals for 1 LAN cable. Based on the HDBaseT g

standard.

Wireless LAN unit ELPAP07

Use when connecting the projector to a computer wirelessly and projecting.

Quick Wireless Connection USB Key ELPAP09

Use when you want to quickly establish one-to-one connection between the projector and a computer with Windows installed.

Polarizer ELPPL01

Attach to this projector when stacking two projectors and projecting 3D images.

Passive 3D Glasses (standard five piece set) ELPGS02A

Passive 3D Glasses (five piece set for children) ELPGS02B

Passive polarized 3D glasses. Use these when viewing 3D images with the projectors.

Document Camera ELPDC11/ELPDC20

Use when projecting images such as books, OHP documents, or slides.

Ceiling pipe (450 mm) * ELPFP13

Ceiling pipe (700 mm) * ELPFP14

Use when installing the projector on a high ceiling.

Ceiling mount * ELPMB22

Use when installing the projector on a ceiling.

* Special expertise is required to suspend the projector from a ceiling. Contact your local dealer or the nearest address provided in the Epson Projector

Contact List.


Optional Accessories and Consumables

Consumables

Lamp unit ELPLP76

Use as a replacement for used lamps.

Air filter ELPAF43

Use as a replacement for used air filters.

157

Screen Size and Projection Distance

Projection Distance (For EB-G6750WU/EB-

G6650WU/EB-G6550WU/EB-G6450WU/EB-

G6250W/EB-G6050W)

A Projection distance

B is the distance from the center of the lens to the base of the screen. This changes depending on the setting for vertical lens shift.

C Center of lens

Standard zoom lens ELPLS06

This section shows the projection distances for models equipped with standard lenses.

158

4:3 Screen Size

50"

60"

70"

80"

100"

150"

200"

250"

102x76

122x91

142x107

163x122

203x152

305x229

406x305

508x381

16:9 Screen Size

150"

200"

250"

290"

50"

60"

80"

100"

111x62

133x75

177x100

221x125

332x187

443x249

553x311

642x361

A

Minimum (Wide) to

Maximum (Tele)

154 - 280

185 - 337

217 - 393

249 - 450

312 - 564

471 - 848

630 - 1132

788 - 1415

A

Minimum (Wide) to

Maximum (Tele)

139 - 254

168 - 305

226 - 408

283 - 511

427 - 769

571 - 1027

715 - 1285

830 - 1491

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-13 - +90

-16 - +108

-19 - +126

-22 - +143

-27 - +179

-40 - +269

-54 - +359

-67 - +448

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-16 - +78

-19 - +94

-25 - +125

-31 - +156

-47 - +234

-63 - +312

-78 - +390

-91 - +452


159

16:10 Screen Size

50"

60"

80"

100"

150"

200"

250"

300"

108x67

130x81

172x108

215x135

323x202

431x269

538x337

646x404

A

Minimum (Wide) to

Maximum (Tele)

135 - 247

163 - 297

219 - 397

275 - 498

416 - 748

556 - 999

696 - 1250

836 - 1501

Short throw zoom lens ELPLU01

4:3 Screen Size

60"

70"

80"

100"

150"

200"

250"

122x91

142x107

163x122

203x152

305x229

406x305

508x381

A

Minimum (Wide) to

Maximum (Tele)

93 - 112

109 - 131

125 - 151

158 - 189

238 - 286

319 - 382

400 - 479

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-12 - +79

-14 - +95

-19 - +127

-24 - +158

-36 - +238

-48 - +317

-59 - +396

-71 - +475

16:9 Screen Size

60"

80"

100"

150"

200"

250"

290"

133x75

177x100

221x125

332x187

443x249

553x311

642x361

A

Minimum (Wide) to

Maximum (Tele)

84 - 101

113 - 136

143 - 171

216 - 259

290 - 347

363 - 434

422 - 505

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-16 - +108

-19 - +126

-22 - +143

-27 - +179

-40 - +269

-54 - +359

-67 - +448

16:10 Screen Size

60"

80"

100"

150"

200"

250"

300"

130x81

172x108

215x135

323x202

431x269

538x337

646x404

A

Minimum (Wide) to

Maximum (Tele)

81 - 98

110 - 132

139 - 167

210 - 252

282 - 337

353 - 423

425 - 508

Rear projection wide lens ELPLR03

Lens shift is not supported.

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-19 - +94

-25 - +125

-31 - +156

-47 - +234

-63 - +312

-78 - +390

-91 - +452

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-14 - +95

-19 - +127

-24 - +158

-36 - +238

-48 - +317

-59 - +396

-71 - +475


4:3 Screen Size

50"

60"

70"

80"

100"

150"

102x76

122x91

142x107

163x122

203x152

305x229

16:9 Screen Size

50"

60"

80"

100"

150"

111x62

133x75

177x100

221x125

332x187

16:10 Screen Size

50" 108x67

60"

80"

130x81

172x108

100"

150"

200"

215x135

323x202

431x269

A

82

99

134

168

254

A

91

110

129

148

186

280

A

80

96

130

163

247

331

160

B

+38

+46

+53

+61

+76

+114

Unit: cm

B

+31

+37

+50

+62

+93

Unit: cm

B

+34

+40

+54

+67

+101

+135

Unit: cm

Middle throw zoom lens ELPLM04

4:3 Screen Size

50"

60"

70"

80"

100"

150"

200"

250"

102x76

122x91

142x107

163x122

203x152

305x229

406x305

508x381

A

Minimum (Wide) to

Maximum (Tele)

275 - 421

332 - 507

389 - 593

446 - 679

560 - 851

844 - 1282

1129 - 1713

1414 - 2143

16:9 Screen Size

150"

200"

250"

290"

50"

60"

80"

100"

111x62

133x75

177x100

221x125

332x187

443x249

553x311

642x361

A

Minimum (Wide) to

Maximum (Tele)

249 - 381

300 - 459

404 - 616

507 - 772

766 - 1163

1024 - 1554

1283 - 1945

1490 - 2258

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-13 - +90

-16 - +108

-19 - +126

-22 - +143

-27 - +179

-40 - +269

-54 - +359

-67 - +448

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-16 - +78

-19 - +94

-25 - +125

-31 - +156

-47 - +234

-63 - +312

-78 - +390

-91 - +452


16:10 Screen Size

50"

60"

80"

100"

150"

200"

250"

300"

108x67

130x81

172x108

215x135

323x202

431x269

538x337

646x404

A

Minimum (Wide) to

Maximum (Tele)

242 - 371

292 - 447

392 - 599

493 - 751

754 - 1131

996 - 1512

1248 - 1892

1499 - 2272

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-12 - +79

-14 - +95

-19 - +127

-24 - +158

-36 - +238

-48 - +317

-59 - +396

-71 - +475


4:3 Screen Size

50"

60"

70"

80"

100"

150"

200"

250"

102x76

122x91

142x107

163x122

203x152

305x229

406x305

508x381

A

Minimum (Wide) to

Maximum (Tele)

410 - 631

496 - 760

581 - 890

667 - 1019

837 - 1278

1264 - 1925

1691 - 2572

2118 - 3219

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-13 - +90

-16 - +108

-19 - +126

-22 - +143

-27 - +179

-40 - +269

-54 - +359

-67 - +448

161

16:9 Screen Size

50"

60"

80"

100"

150"

200"

250"

290"

111x62

133x75

177x100

221x125

332x187

443x249

553x311

642x361

16:10 Screen Size

150"

200"

250"

300"

50"

60"

80"

100"

108x67

130x81

172x108

215x135

323x202

431x269

538x337

646x404

A

Minimum (Wide) to

Maximum (Tele)

371 - 571

449 - 689

604 - 924

759 - 1159

1146 - 1746

1534 - 2334

1921 - 2921

2231 - 3391

A

Minimum (Wide) to

Maximum (Tele)

361 - 555

436 - 670

587 - 898

738 - 1127

1115 - 1699

1492 - 2270

1869 - 2842

2246 - 3414

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-16 - +78

-19 - +94

-25 - +125

-31 - +156

-47 - +234

-63 - +312

-78 - +390

-91 - +452

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-12 - +79

-14 - +95

-19 - +127

-24 - +158

-36 - +238

-48 - +317

-59 - +396

-71 - +475


Long throw zoom lens ELPLL06

4:3 Screen Size

50"

60"

70"

80"

100"

150"

200"

250"

16:9 Screen Size

150"

200"

250"

290"

50"

60"

80"

100"

111x62

133x75

177x100

221x125

332x187

443x249

553x311

642x361

102x76

122x91

142x107

163x122

203x152

305x229

406x305

508x381

A

Minimum (Wide) to

Maximum (Tele)

620 - 842

748 - 1015

876 - 1187

1003 - 1359

1259 - 1703

1897 - 2564

2536 - 3425

3175 - 4285

A

Minimum (Wide) to

Maximum (Tele)

561 - 763

677 - 919

909 - 1232

1141 - 1545

1721 - 2326

2301 - 3107

2880 - 3889

3344 - 4514

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-13 - +90

-16 - +108

-19 - +126

-22 - +143

-27 - +179

-40 - +269

-54 - +359

-67 - +448

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-16 - +78

-19 - +94

-25 - +125

-31 - +156

-47 - +234

-63 - +312

-78 - +390

-91 - +452

162

16:10 Screen Size

50"

60"

80"

100"

150"

200"

250"

300"

108x67

130x81

172x108

215x135

323x202

431x269

538x337

646x404

A

Minimum (Wide) to

Maximum (Tele)

546 - 742

659 - 894

884 - 1198

1110 - 1502

1674 - 2263

2238 - 3023

2802 - 3783

3366 - 4544

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-12 - +79

-14 - +95

-19 - +127

-24 - +158

-36 - +238

-48 - +317

-59 - +396

-71 - +475


Projection Distance (For EB-G6350/EB-G6150)

A Projection distance

B is the distance from the center of the lens to the base of the screen. This changes depending on the setting for vertical lens shift.

C Center of lens

Standard zoom lens ELPLS06

This section shows the projection distances for models equipped with lenses.

163

4:3 Screen Size

150"

200"

250"

300"

30"

40"

50"

60"

80"

100"

61x46

81x61

102x76

122x91

163x122

203x152

305x229

406x305

508x381

610x457

16:9 Screen Size

60"

80"

100"

150"

200"

28"

30"

40"

50"

62x35

66x37

89x50

111x62

133x75

177x100

221x125

332x187

443x249

A

Minimum (Wide) to

Maximum (Tele)

76 - 141

103 - 189

130 - 238

157 - 286

211 - 383

265 - 479

400 - 721

535 - 963

670 - 1205

804 - 1447

A

Minimum (Wide) to

Maximum (Tele)

77 - 143

83 - 154

113 - 207

142 - 259

171 - 312

230 - 417

289 - 523

436 - 786

583 - 1050

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-3 - +49

-5 - +66

-6 - +82

-7 - +98

-9 - +131

-12 - +164

-17 - +246

-23 - +328

-29 - +410

-35 - +492

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-9 - +44

-10 - +47

-13 - +63

-17 - +79

-20 - +95

-27 - +126

-33 - +158

-50 - +237

-67 - +316


16:9 Screen Size

250"

275"

553x311

609x342

16:10 Screen Size

70"

80"

100"

150"

29"

30"

50"

60"

200"

250"

280"

62x39

65x40

108x67

130x81

151x94

172x108

215x135

323x202

431x269

538x337

603x377

A

Minimum (Wide) to

Maximum (Tele)

730 - 1313

803 - 1445

A

Minimum (Wide) to

Maximum (Tele)

78 - 145

81 - 150

138 - 252

167 - 303

195 - 355

224 - 406

281 - 508

424 - 765

567 - 1021

710 - 1277

796 - 1431

B

Vertical Lens Shift

Top to Bottom

-83 - +395

-92 - +434

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-7 - +47

-8 - +48

-13 - +80

-15 - +96

-18 - +112

-21 - +128

-26 - +160

-39 - +241

-51 - +321

-64 - +401

-72 - +449

Short throw zoom lens ELPLU01

4:3 Screen Size

60" 122x91

A

Minimum (Wide) to

Maximum (Tele)

78 - 95

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-7 - +98

164

4:3 Screen Size

80"

100"

150"

200"

250"

300"

163x122

203x152

305x229

406x305

508x381

610x457

16:9 Screen Size

60"

80"

100"

150"

200"

250"

275"

133x75

177x100

221x125

332x187

443x249

553x311

609x342

16:10 Screen Size

60"

70"

80"

130x81

151x94

172x108

A

Minimum (Wide) to

Maximum (Tele)

105 - 127

133 - 160

201 - 242

270 - 324

338 - 407

407 - 489

A

Minimum (Wide) to

Maximum (Tele)

85 - 103

115 - 139

145 - 175

220 - 264

294 - 354

369 - 443

407 - 489

A

Minimum (Wide) to

Maximum (Tele)

83 - 101

97 - 118

112 - 135

B

Vertical Lens Shift

Top to Bottom

-9 - +131

-12 - +164

-17 - +246

-23 - +328

-29 - +410

-35 - +492

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-20 - +95

-27 - +126

-33 - +158

-50 - +237

-67 - +316

-83 - +395

-92 - +435

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-15 - +96

-18 - +112

-21 - +128


165

16:10 Screen Size

100"

150"

200"

250"

283"

215x135

323x202

431x269

538x337

610x381

Rear projection wide lens ELPLR03

Lens shift is not supported.

4:3 Screen Size

80"

100"

150"

200"

30"

40"

50"

60"

61x46

81x61

102x76

122x91

163x122

203x152

305x229

406x305

A

125

157

237

318

44

60

76

92

16:9 Screen Size

28" 62x35

30"

40"

66x37

89x50

A

Minimum (Wide) to

Maximum (Tele)

141 - 170

214 - 257

286 - 344

359 - 431

407 - 489

A

45

48

66

B

Vertical Lens Shift

Top to Bottom

-26 - +160

-39 - +241

-51 - +321

-64 - +401

-73 - +454

16:9 Screen Size

50" 111x62

60"

80"

133x75

177x100

100"

150"

184"

221x125

332x187

407x229

A

83

101

136

171

259

318

B

+61

+76

+114

+152

+23

+30

+38

+46

Unit: cm

B

+17

+19

+25

Unit: cm

60"

70"

80"

100"

16:10 Screen Size

29" 62x39

30"

50"

65x40

108x67

150"

189"

130x81

151x94

172x108

215x135

323x202

407x254


4:3 Screen Size

40"

50"

60"

81x61

102x76

122x91

A

Minimum (Wide) to

Maximum (Tele)

184 - 283

232 - 357

281 - 430

A

115

132

166

252

318

45

47

81

98

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-5 - +66

-6 - +82

-7 - +98

B

+31

+37

+50

+62

+93

+114

B

+47

+54

+67

+101

+127

+20

+20

+34

+40

Unit: cm


166

4:3 Screen Size

80"

100"

150"

200"

250"

300"

163x122

203x152

305x229

406x305

508x381

610x457

16:9 Screen Size

80"

100"

150"

200"

37"

40"

50"

60"

250"

275"

82x46

89x50

111x62

133x75

177x100

221x125

332x187

443x249

553x311

609x342

A

Minimum (Wide) to

Maximum (Tele)

378 - 577

475 - 723

717 - 1090

959 - 1456

1202 - 1823

1444 - 2190

A

Minimum (Wide) to

Maximum (Tele)

184 - 283

201 - 310

254 - 390

307 - 469

412 - 629

518 - 789

782 - 1188

1046 - 1588

1310 - 1987

1444 - 2189

B

Vertical Lens Shift

Top to Bottom

-9 - +131

-12 - +164

-17 - +246

-23 - +328

-29 - +410

-35 - +492

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-12 - +58

-13 - +63

-17 - +79

-20 - +95

-27 - +126

-33 - +158

-50 - +237

-67 - +316

-83 - +395

-92 - +435

16:10 Screen Size

150"

200"

250"

283"

38"

50"

60"

70"

80"

100"

82x51

108x67

130x81

151x94

172x108

215x135

323x202

431x269

538x337

610x381

A

Minimum (Wide) to

Maximum (Tele)

184 - 284

247 - 379

298 - 456

350 - 534

401 - 612

504 - 767

761 - 1156

1017 - 1544

1274 - 1933

1444 - 2189


4:3 Screen Size

100"

150"

200"

250"

40"

50"

60"

80"

81x61

102x76

122x91

163x122

203x152

305x229

406x305

508x381

A

Minimum (Wide) to

Maximum (Tele)

274 - 424

347 - 535

419 - 645

565 - 865

710 - 1086

1073 - 1637

1436 - 2188

1799 - 2738

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-10 - +61

-13 - +80

-15 - +96

-18 - +112

-21 - +128

-26 - +160

-39 - +241

-51 - +321

-64 - +401

-73 - +454

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-5 - +66

-6 - +82

-7 - +98

-9 - +131

-12 - +164

-17 - +246

-23 - +328

-29 - +410


167

4:3 Screen Size

300" 610x457

16:9 Screen Size

80"

100"

150"

200"

37"

40"

50"

60"

250"

275"

82x46

89x50

111x62

133x75

177x100

221x125

332x187

443x249

553x311

609x342

16:10 Screen Size

38"

50"

60"

70"

80"

82x51

108x67

130x81

151x94

172x108

A

Minimum (Wide) to

Maximum (Tele)

2162 - 3289

A

Minimum (Wide) to

Maximum (Tele)

274 - 424

300 - 464

379 - 584

458 - 704

617 - 944

775 - 1184

1170 - 1784

1566 - 2385

1962 - 2985

2162 - 3289

A

Minimum (Wide) to

Maximum (Tele)

274 - 424

368 - 568

445 - 685

522 - 801

599 - 918

B

Vertical Lens Shift

Top to Bottom

-35 - +492

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-12 - +58

-13 - +63

-17 - +79

-20 - +95

-27 - +126

-33 - +158

-50 - +237

-67 - +316

-83 - +395

-92 - +435

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-10 - +61

-13 - +80

-15 - +96

-18 - +112

-21 - +128

16:10 Screen Size

100"

150"

200"

250"

283"

215x135

323x202

431x269

538x337

610x381

A

Minimum (Wide) to

Maximum (Tele)

753 - 1152

1138 - 1736

1523 - 2320

1908 - 2904

2162 - 3289

Long throw zoom lens ELPLL06

4:3 Screen Size

40"

150"

200"

250"

300"

50"

60"

80"

100"

81x61

102x76

122x91

163x122

203x152

305x229

406x305

508x381

610x457

A

Minimum (Wide) to

Maximum (Tele)

416 - 568

525 - 714

634 - 861

851 - 1154

1068 - 1447

1612 - 2179

2155 - 2912

2699 - 3644

3242 - 4376

B

Vertical Lens Shift

Top to Bottom

-26 - +160

-39 - +241

-51 - +321

-64 - +401

-73 - +454

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-5 - +66

-6 - +82

-7 - +98

-9 - +131

-12 - +164

-17 - +246

-23 - +328

-29 - +410

-35 - +492


16:9 Screen Size

150"

200"

250"

275"

37"

40"

50"

60"

80"

100"

82x46

89x50

111x62

133x75

177x100

221x125

332x187

443x249

553x311

609x342

16:10 Screen Size

80"

100"

150"

200"

250"

38"

50"

60"

70"

82x51

108x67

130x81

151x94

172x108

215x135

323x202

431x269

538x337

A

Minimum (Wide) to

Maximum (Tele)

416 - 568

455 - 620

574 - 780

692 - 939

929 - 1259

1166 - 1578

1758 - 2376

2350 - 3174

2942 - 3972

3242 - 4376

A

Minimum (Wide) to

Maximum (Tele)

416 - 568

558 - 758

673 - 913

788 - 1069

903 - 1224

1134 - 1535

1710 - 2311

2286 - 3087

2862 - 3864

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-12 - +58

-13 - +63

-17 - +79

-20 - +95

-27 - +126

-33 - +158

-50 - +237

-67 - +316

-83 - +395

-92 - +435

Unit: cm

B

Vertical Lens Shift

Top to Bottom

-10 - +61

-13 - +80

-15 - +96

-18 - +112

-21 - +128

-26 - +160

-39 - +241

-51 - +321

-64 - +401

168

16:10 Screen Size

283" 610x381

A

Minimum (Wide) to

Maximum (Tele)

3242 - 4376

B

Vertical Lens Shift

Top to Bottom

-73 - +454

Supported Monitor Displays

Supported Resolutions

Computer signals (analog RGB)

Signal

VGA

SVGA

XGA

WXGA

WXGA+

WXGA++

SXGA

SXGA+

WSXGA+ * 1

UXGA

WUXGA * 2

MAC13"

MAC16"

MAC19"

Refresh Rate (Hz)

60/72/75/85

56/60/72/75/85

60/70/75/85

60

60

60/75/85

60/75/85

60

70/75/85

60/75/85

60/75/85

60/75

60

60

60

67

75

75

59

Resolution (Dots)

640x480

800x600

1024x768

1280x768

1366x768

1280x800

1440x900

1600x900

1152x864

1280x1024

1280x960

1400x1050

1680x1050

1600x1200

1920x1200

640x480

832x624

1024x768

1024x768

169

Signal

MAC21"

Refresh Rate (Hz)

75

Resolution (Dots)

1152x870

* 1 Only compatible when Wide is selected as the Resolution from the

Configuration menu. (This is not available for EB-G6350/EB-G6150.)

* 2 EB-G6750WU/EB-G6650WU/EB-G6550WU/EB-G6450WU only. Only compatible when VESA CVT-RB (Reduced Blanking) signal is input.

Even when signals other than those mentioned above are input, it is likely that the image can be projected. However, not all functions may be supported.

Component Video

Signal

SDTV (480i)

SDTV (576i)

SDTV (480p)

SDTV (576p)

HDTV (720p)

HDTV (1080i)

HDTV (1080p) *

Refresh Rate (Hz)

60

50

60

50

50/60

50/60

50/60

* EB-G6750WU/EB-G6650WU/EB-G6550WU/EB-G6450WU only

Resolution (Dots)

720x480

720x576

720x480

720x576

1280x720

1920x1080

1920x1080

Composite video

Signal

TV (NTSC)

TV (SECAM)

TV (PAL)

Refresh Rate (Hz)

60

50

50/60

Resolution (Dots)

720x480

720x576

720x576

Supported Monitor Displays

170

Input signal from the HDMI port and DisplayPort (EB-G6750WU/

EB-G6650WU/EB-G6550WU/EB-G6450WU/EB-G6250W/EB-G6050W)

Signal

VGA

SVGA

XGA

WXGA

WXGA+

WXGA++

WSXGA+

SXGA

Refresh Rate (Hz)

60

60

60

60

60

60

60

60

60

60

60

60

60

60

60

Resolution (Dots)

640x480

800x600

1024x768

1280x800

1280x768 * 1

1366x768

1440x900

1600x900

1680x1050

1280x960

1280x1024

1400x1050

1600x1200

1920x1200

720x480

SXGA+

UXGA

WUXGA * 2

SDTV

(480i * 3 /480p)

SDTV

(576i * 3 /576p)

HDTV (720p)

HDTV (1080i)

HDTV (1080p)

50

50/60

50/60

24 * 3 /30 * 3 /50/60

720x576

1280x720

1920x1080

1920x1080

* 1 DisplayPort input only

* 2 EB-G6750WU/EB-G6650WU/EB-G6550WU/EB-G6450WU only. Only compatible when VESA CVT-RB (Reduced Blanking) signal is input.

* 3 HDMI input only

Input signal from the HDMI port and DisplayPort (EB-G6350/EB-

G6150)

Signal

VGA

SVGA

XGA

WXGA

WXGA+

WXGA++

SXGA

SXGA+

UXGA

SDTV

(480i * 2 /480p)

SDTV

(576i * 2 /576p)

HDTV (720p)

HDTV (1080i)

HDTV (1080p)

* 1 DisplayPort input only

* 2 HDMI input only

Refresh Rate (Hz)

60

60

60

60

60

60

60

60

60

60

60

60

60

50

50/60

50/60

24 * 2 /30 * 2 /50/60

Resolution (Dots)

640x480

800x600

1024x768

1280x800

1280x768 * 1

1366x768 * 2

1440x900

1600x900

1280x960

1280x1024

1400x1050

1600x1200

720x480

720x576

1280x720

1920x1080

1920x1080

Specifications

171

Projector General Specifications

Product name

Dimensions

LCD panel size

Display method

Resolution

EB-G6750WU EB-G6650WU EB-G6550WU EB-G6450WU EB-G6350 EB-G6250W

505 (W) x 144 (H) x 382 (D) mm (not including raised section)

0.76" Wide 0.79" 0.76" Wide

2,304,000 pixels

WUXGA (1920 (W) x 1200 (H) dots) x 3

Polysilicon TFT active matrix

786,432 pixels

XGA (1024 (W) x 768 (H) dots) x 3

Manual

Manual (1 - 1.8)

1,024,000 pixels

WXGA (1280

(W) x 800 (H) dots) x 3

EB-G6150

0.79"

786,432 pixels

XGA (1024 (W) x 768 (H) dots) x 3

EB-G6050W

0.76" Wide

1,024,000 pixels

WXGA (1280

(W) x 800 (H) dots) x 3

Focus adjustment

Zoom adjustment *1

Lens shift *2

Lamp

Max. audio output

Speaker

Power supply

Manual (Vertical direction: Maximum approx. 67%, Horizontal direction:

Maximum approx. 30%)

Manual (Vertical direction: Maxi‐ mum approx.

57%, Horizontal direction: Maxi‐ mum approx.

30%)

UHE lamp, 380 W Model No.: ELPLP76



30%)

10 W monaural

1

100-240V AC±10% 50/60Hz

5.7-2.5A

100-240V AC

±10% 50/60Hz

5.3-2.3A

100-240V AC

±10% 50/60Hz

4.7-2.1A

100-240V AC±10% 50/60Hz

5.7-2.5A



30%)



30%)

100-240V AC

±10% 50/60Hz

5.3-2.3A

100-240V AC

±10% 50/60Hz

5.0-2.2A

Specifications

172

Power consumption

100 to

120 V area

220 to

240 V area

Operating: 568 W

Standby power consumption (Com‐ munication On): 2.8 W

Standby power consumption (Com‐ munication Off): 0.31 W

Operating: 542 W



Operating: 528

W

Standby power consumption

(Communication

On): 2.8 W


(Communication

Off): 0.31 W

Operating: 504

W


(Communication

On): 3.3 W


(Communication

Off): 0.41 W

Operating: 468

W


(Communication

On): 2.8 W


(Communication

Off): 0.31 W

Operating: 449

W


(Communication

On): 3.3 W


(Communication

Off): 0.41 W

Operating: 568 W



Operating: 542 W



Altitude 0 to 3048 m

0 to +45˚C * 3 (No condensation)

Operating: 528

W


(Communication

On): 2.8 W


(Communication

Off): 0.31 W

Operating: 504

W


(Communication

On): 3.3 W


(Communication

Off): 0.41 W

Operating: 498

W


(Communication

On): 2.8 W


(Communication

Off): 0.31 W

Operating: 477

W


(Communication

On): 3.3 W


(Communication

Off): 0.41 W

Operating altitude

Operating temperature

Storage temperature

Mass

-10 to +60˚C (No condensation)

Approx. 9.7 kg Approx. 9.7 kg Approx. 9.7 kg Approx. 9.7 kg Approx. 9.7 kg Approx. 9.7 kg Approx. 9.7 kg Approx. 9.7 kg

* 1 The specifications are when a standard zoom lens is attached.

* 2 The rear projection wide lens ELPLR03 does not support lens shift.

* 3 The operating temperature is 0 to +45˚C when Power Consumption is set to ECO or Temp Interlock, and 0 to +40˚C when it is set to Normal at an altitude of 0 to

1499m.

The operating temperature is 0 to +40˚C when Power Consumption is set to ECO or Temp Interlock, and 0 to +35˚C when it is set to Normal at an altitude of 1500 to

3048m.

Product name EB-

G6750WU

EB-

G6650WU

EB-

G6550WU

EB-

G6450WU

EB-G6350 EB-G6250W EB-G6150 EB-G6050W

Specifications

Connectors

Computer Port

Audio1 port

BNC port

Audio2 port

DisplayPort

HDMI port

Audio3 port

S-Video port

Video port

Audio-L/R port

Audio Out port

Monitor Out port

HDBaseT port

LAN port

Service port *

RS-232C port

Remote port

USB port (Only for

Wireless LAN unit) *

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

RJ-45

Mini D-Sub15-pin (female) blue

Stereo mini jack (3.5Ф)

5BNC (female)


DisplayPort

HDMI HDCP supported (Audio is only supported by PCM)


Mini DIN 4-pin

RCA pin jack

RCA pin jack x 2 (L-R)


Mini D-Sub15-pin (female) black

-

RJ-45

Mini USB Connector (Type B)

Mini D-Sub 9-pin (male)


USB connector (Type A)

* USB 2.0 is supported. However, USB ports are not guaranteed to operate all devices that support USB.

This product is also designed for IT power distribution system with phase-to-phase voltage 230V.

173

Specifications

174

DECLARATION of CONFORMITY

According to 47CFR, Part 2 and 15

Class B Personal Computers and Peripherals; and/or

CPU Boards and Power Supplies used with Class B Personal Computers

We:

Located at:

Tel:

Epson America, Inc.

3840 Kilroy Airport Way

MS: 3-13

Long Beach, CA 90806

562-981-3840

Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Trade Name: EPSON

Type of Product:

Model:

LCD Projector

H508C/H509C/H510C/H511C/H512C/H513C/

H535C/H542C

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

Appearance

252.5

505

A Center of lens

B Distance from center of lens to suspension bracket fixing point

18.6

10

322

175

Units: mm

Glossary

176

This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.

Ad hoc mode

AMX Device Discovery

Aspect Ratio

Component Video

Composite video

Contrast

DHCP

DICOM

Gateway Address

HDBaseT

HDCP

HDTV

Infrastructure mode

Interlace

A method of wireless LAN connection that communicates with wireless LAN clients without using an access point.

AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.

Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).

See the AMX Web site for more details.

URL http://www.amx.com/

The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.

SDTV and general computer displays have an aspect ratio of 4:3.

A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or

Pr).

A method that combines the video signal into a luminance component and a color component for transmission down a single cable.

The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to make them appear softer. Adjusting this particular property of an image is called contrast adjustment.

An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP address g

to equipment connected to a network.

An acronym for Digital Imaging and Communications in Medicine. An international standard that defines image standards and a communications protocol for medical images.

This is a server (router) for communicating across a network (subnet) divided according to subnet mask

g .

The connection standard for consumer electronics determined by the HDBaseT Alliance. Communicates various control signals such as uncompressed HD video, audio and 100BASE-TX Ethernet using a LAN cable.

HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting digital signals sent over DVI and HDMI ports. Because the HDMI port and DisplayPort on this projector supports HDCP, it can project digital images protected by HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.

An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.

• Vertical resolution of 720p or 1080i or greater (p = Progressive

• Screen aspect ratio g

of 16:9

g , i = Interlace g )

A method for wireless LAN connection in which devices communicate through access points.

Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.

Images are more likely to flicker because one frame is displayed every other line.

Glossary

177

IP Address A number to identify a computer connected to a network.

Progressive

Refresh Rate

SDTV

SNMP sRGB

Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount of flicker in images decreases because the volume of information has doubled compared with an interlace system.

The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh rate and is expressed in hertz (Hz).

An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV

g High-

Definition Television.

An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and computers connected to a TCP/IP network.

An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source to sRGB.

This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.

Subnet Mask

Sync.

The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called

Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.

Tracking

Trap IP Address

The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If Tracking is not carried out correctly, wide vertical stripes appear in the signal.

This is the IP address g

for the destination computer used for error notification in SNMP.

WPS (Wi-Fi Protected Setup) Wi-Fi Protected Setup has been devised by the Wi-Fi Alliance as a means of easily setting up and securing a wireless LAN.

General Notes

178

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko

Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the

U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as

Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

The contents of this guide may be changed or updated without further notice.

Illustrations in this guide and the actual projector may differ.

Restriction of Use

When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/precision devices etc, you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability. Because this product was not intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care etc, please make your own judgment on this product’s suitability after a full evaluation.

Trademarks and Copyrights

Mac and Mac OS are trademarks of Apple Inc.

Microsoft, Windows, Windows Vista, PowerPoint, and Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.

PJLink trademark is a trademark applied for registration or is already registered in

Japan, the United States of America and other countries and areas.

This product includes RSA BSAFE ™ software from RSA Security Inc. RSA is a registered trademark of RSA Security Inc. BSAFE RSA Security Inc. is a registered trade mark in the United States and other countries.

WPA ™ , WPA2 ™ and Wi-Fi Protected Setup ™ are registered trademarks of Wi-Fi

Alliance.

The DisplayPort Certified Logo and DisplayPort Icons are Registered Trademarks of the

Video Electronics Standards Association (VESA).

The word DisplayPort is a Registered Trademark of VESA in various countries around the world.

HDBaseT ™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

©SEIKO EPSON CORPORATION 2013. All rights reserved.

Index

179

3

3D Setup ........................................................ 83

A

A/V Mute ................................................ 11, 63

A/V Settings ................................................. 88

Abs. Color Temp. ........................................ 82

Administrator Password ............................. 98

Administrator Settings menu .................... 98

Air exhaust vent ............................................. 8

Air Filter Notice ........................................... 86

Air filter replacement period ................... 131

AMX Device Discovery .............................. 98

Aspect ...................................................... 47, 84

Audio Out port ............................................ 10

Audio1 port .................................................... 9

Audio2 port .................................................... 9

Audio3 port .................................................. 10

Audio-L/R port .............................................. 9

Auto Iris ........................................................ 82

Auto Setup .................................................... 83

B

Basic menu .................................................... 91

Beep ............................................................... 88

BNC port ......................................................... 9

BNC Sync Termination .............................. 87

Bonjour ......................................................... 99

Brightness ..................................................... 81

Brightness Level ........................................... 89

C

CA certificate .............................................. 100

Ceiling ........................................................... 87

Ceiling mount fixing points ....................... 11

Certificates .................................................. 146

Cleaning ...................................................... 125

Cleaning the air filter and air intake vent

........................................................................ 125

Cleaning the projector's surface .............. 125

Client Certificate ........................................ 100

Color adjustment ......................................... 82

Color Mode ............................................ 46, 81

Color Saturation .......................................... 81

Color Uniformity ......................................... 86

Computer port ............................................... 9

Configuration menu .................................... 78

Connect to a Network Projector ............. 142

Consumables .............................................. 157

Contrast ........................................................ 81

Control panel ............................................... 11

Control Panel Lock ...................................... 85

Crestron RoomView ........................... 98, 152

Cross .............................................................. 64

D

Date & Time ................................................. 88

DHCP ............................................................ 97

DICOM SIM ................................................. 46

Direct Power On .......................................... 87

Direction ....................................................... 87

Display ........................................................... 86

Display Background .................................... 86

DisplayPort ................................................... 10

Distance ...................................................... 158

Document Camera .................................... 156

Dynamic ........................................................ 46

E

EasyMP Monitor ....................................... 145

Edge Blending ........................................ 55, 89

Esc .................................................................. 12

ESC/VP21 ................................................... 150

Extended menu ............................................ 86

E-Zoom ......................................................... 64

F

Filter indicator ........................................... 106

Focus ring ....................................................... 8

Frame Interpolation .................................... 83

Freeze ............................................................. 64

Front .............................................................. 87

Front adjustable foot ................................... 10

Full Lock ....................................................... 74

G

Gateway Address ................................... 93, 97

Geometric Correction ................................. 85

H

H/V-Keystone .............................................. 85

HDBaseT ....................................................... 89

HDBaseT port .............................................. 10

HDMI port ................................................... 10

Help function ............................................. 105

High Altitude Mode .................................... 87

Index

180

Horizontal lens shift dial .............................. 8

How to replace the air filter ..................... 131

How to replace the lamp ........................... 129

I

Image menu .................................................. 81

Image Processing ......................................... 84

Indicators ........................................... 106, 107

Info menu ................................................... 102

Input Signal .......................................... 84, 102

Installation requirements ........................... 20

Inv Direction Button ................................... 87

IP Address ..................................................... 97

L

Lamp cover ..................................................... 9

Lamp hours ................................................ 102

Lamp indicator ........................................... 106

Lamp replacement period ........................ 128

Language ....................................................... 89

Lens shift ....................................................... 24

Lens shift dial lock ......................................... 8

Lens Type ...................................................... 88

Lens unit removal button ............................. 8

M

Mail Notification ................................. 99, 148

Mail Notification menu .............................. 99

Manage Certificates menu ........................ 100

Memory ......................................................... 85

Menu ............................................................. 12

Menu Position .............................................. 86

Message Broadcasting ......................... 99, 145

Messages ....................................................... 86

Monitor displays ........................................ 169

Monitor Out port ......................................... 10

Monitor Password ....................................... 98

Mosquito NR ................................................ 83

Multi-Projection .................................... 46, 89

Multi-screen ................................................. 89

N

O

Operating temperature ............................. 172

Operation ...................................................... 87

Optional accessories .................................. 156

Overheating ................................................ 107

Overscan ....................................................... 84

P

Network Configuration .............................. 90

Network Host Name ................................... 98

Network information .................................. 90

Network menu ............................................. 89

Noise Reduction ........................................... 83

Notification email address 1/2/3 ............... 99

Panel Alignment .......................................... 86

Part names and functions ............................. 8

Password protect .......................................... 72

Photo ............................................................. 46

PJLink .......................................................... 151

PJLink Password .......................................... 98

Port Number ................................................ 99

Position ......................................................... 83

Power Consumption ................................... 85

Q

Quick Corner ............................................... 85

Quick Wireless Connection USB Key .... 143

R

Power indicator .......................................... 106

Power inlet ...................................................... 9

Power On Protection .................................. 72

Presentation .................................................. 46

Priority Gateway .......................................... 98

Problem solving ......................................... 106

Progressive .................................................... 83

Projection ...................................................... 87

Projection lens .............................................. 16

Projector ID .................................................. 28

Projector keyword ....................................... 92

Projector Name ............................................ 91

Projector setup ........................................... 145

Reading mail ............................................... 148

Rear ................................................................ 87

Rear feet ........................................................ 10

Refresh Rate ................................................ 102

Remote control ............................................ 12

Remote control button lock ....................... 75

Remote control ID ....................................... 29

Remote port .................................................... 9

Remote receiver ............................................. 8

Replacing batteries ....................................... 14

Reset All ...................................................... 103

Reset Memory ............................................ 103

Reset menu ................................................. 103

Index

181

Resetting the lamp operating time

................................................................ 103, 131

Resolution ............................................. 83, 102

RoomView .................................................. 152

RS-232C port .................................................. 9

S

Scale ............................................................... 84

Schedule ........................................................ 69

Schedule Settings ......................................... 89

Screen ............................................................ 86

Screen settings .............................................. 22

Screen Size .................................................... 61

Screen size ................................................... 158

Search Access Point ..................................... 94

Secure HTTP ................................................ 98

Security menu .............................................. 94

Self-signed Certificate ............................... 100

Setting a Notification Event ....................... 99

Settings menu ............................................... 84

Sharpness ...................................................... 82

Signal menu .................................................. 82

Sleep Mode ................................................... 87

SMTP Server ................................................. 99

SNMP .......................................................... 149

SNMP menu ............................................... 100

Soft keyboard ................................................ 91

Source .................................................... 60, 102

Source Search ......................................... 11, 41

Specifications ............................................. 171

Split Screen ................................................... 85

Split Screen Setup ........................................ 60

Sports ............................................................. 46 sRGB .............................................................. 46

Standby Mode .............................................. 88

Startup Screen .............................................. 86

Startup Source Search ................................. 88

Status indicators ............................................. 8

Storage temperature .................................. 172

Subnet Mask ................................................. 97

Supported monitor displays ..................... 169

S-Video port ................................................. 10

Swap Screens ................................................ 61

Sync Info ..................................................... 102

Sync. ............................................................... 83

T

U

User Button .................................................. 85

User's Logo ................................................... 65

User's Logo Protection ................................ 72

V

Temp indicator .......................................... 106

Test Pattern ............................................ 23, 85

Theatre .......................................................... 46

Tint ................................................................ 82

Tracking ........................................................ 83

Trap IP Address 1/2 .................................. 101

Vertical lens shift dial .................................... 8

Video port ....................................................... 9

Video Range ................................................. 83

Video Signal ......................................... 84, 102

Volume .......................................................... 85

Volume buttons ........................................... 11

W

Web browser .............................................. 145

Web Control ............................................... 145

Web Control Password ............................... 98

Web Remote ............................................... 149

Web Server Certificate .............................. 100

Wired LAN menu ........................................ 97

Wireless LAN menu .................................... 92

Wireless LAN Power ................................... 92

WPA/WPA2-EAP ....................................... 96

WPA/WPA2-PSK ........................................ 95

Z

Zoom ring ....................................................... 8