LC-XB33 RS-232 Extended Serial Commands

EXPAND SERIAL COMMAND

FUNCTIONAL SPECIFICATIONS

LC-XB33

Ver. 1.00

LC-XB33 Expand Serial Command Functional Specifications

CONTENTS

1. OverView .........................................................................................................................7

2. Serial Interface Specification ........................................................................................7

2.1 Transfer Specification ............................................................................................7

2.2 Connection ..............................................................................................................7

3. Notes for communication..............................................................................................8

4. Name Definition ..............................................................................................................8

5. Functional Execution Command Table........................................................................9

5.1 Image Command Table...........................................................................................9

5.2 PC Adjust Control Command Table ......................................................................9

5.3 Video Control Command Table..............................................................................9

5.4 Input Control Command Table ..............................................................................9

5.5 Screen Command Table .......................................................................................10

5.6 Lamp Command Table..........................................................................................10

5.7 Sound Command Table ........................................................................................10

5.8 Setting Command Table .......................................................................................10

6. Status Read Command Table......................................................................................11

6.1 Image Status Read Command Table ...................................................................11

6.2 PC Adjust Status Read Command Table ............................................................11

6.3 Video Status Read Command Table....................................................................11

6.4 Input Status Read Command Table.....................................................................11

6.5 Screen Status Read Command Table .................................................................11

6.6 Lamp Status Read Command Table....................................................................12

6.7 Sound Status Read Command Table ..................................................................12

6.8 Setting Status Read Command Table .................................................................12

6.9 Other Status Read Command ..............................................................................12

7. Error Code Table ..........................................................................................................13

8. Functional Execution Command ................................................................................14

8.1 Format ....................................................................................................................14

8.2 Transfer Example ..................................................................................................14

8.3 Operation Requirements ......................................................................................14

8.4 Image Command ...................................................................................................15

8.4.1 CF_BRIGHT Command .................................................................................15

8.4.2 CF_CONT Command .....................................................................................15

8.4.3 CF_COLOR Command ..................................................................................15

8.4.4 CF_TINT Command .......................................................................................16

8.4.5 CF_SHARP Command...................................................................................16

8.4.6 CF_GAMMA Command .................................................................................16

8.4.7 CF_WBAL - Command ..................................................................................17

8.4.8 CF_COLTEMP Command ..............................................................................17

2/51


8.4.9 CF_PROGV Command ..................................................................................17

8.4.10 CF_NZRED Command...................................................................................18

8.4.11 CF_IMAGE Command ...................................................................................18

8.4.12 CF_IMAGEADJ Command ............................................................................18

8.5 PC Adjust Control Command ..............................................................................19

8.5.1 CF_FSYNC Command ...................................................................................19

8.5.2 CF_TDOTS Command ...................................................................................19

8.5.3 CF_CLAMP Command...................................................................................19

8.5.4 CF_H – POS Command .................................................................................20

8.5.5 CF_V – POS Command .................................................................................20

8.5.6 CF_DDOTS Command...................................................................................20

8.5.7 CF_DLINE Command ....................................................................................21

8.5.8 CF_PCSTORE Command..............................................................................21

8.5.9 CF_PCMODEFREE Command......................................................................21

8.6 Video Control Command......................................................................................22

8.6.1 CF_AVDDOTS Command..............................................................................22

8.6.2 CF_AVDLINE Command................................................................................22

8.6.3 CF_AVHPOS Command ................................................................................22

8.6.4 CF_AVVPOS Command ................................................................................22

8.6.5 CF_AVSERV Command.................................................................................23

8.7 Input Control Command.......................................................................................24

8.7.1 CF_INPUT Command ....................................................................................24

8.7.2 CF_SOURCE Command................................................................................24

8.7.3 CF_INPUT_%1_%2 Command ......................................................................24

8.7.4 CF_SYSTEM Command ................................................................................25

8.8 Screen Control Command ...................................................................................26

8.8.1 CF_SCREEN Command ................................................................................26

8.8.2 CF_VSCALE Command.................................................................................26

8.8.3 CF_VPOS Command .....................................................................................27

8.8.4 CF_HSCALE Command..............................................................................27

8.8.5 CF_HPOS Command .....................................................................................28

8.8.6 CF_DZCENT Command.................................................................................28

8.8.7 CF_KEYSTONE Command ...........................................................................28

8.8.8 CF_KYSTNMODE Command ........................................................................28

8.9 Lamp Command ....................................................................................................29

8.9.1 CF_LAMPH Command ..................................................................................29

8.9.2 CF_LAMPMODE Command ..........................................................................29

8.10 Sound Command ..................................................................................................29

8.10.1 CF_VOLUME Command................................................................................29

8.10.2 CF_MUTE Command .....................................................................................29

3/51


8.11 Setting Command .................................................................................................30

8.11.1 CF_BBACK Command ..................................................................................30

8.11.2 CF_DISP Command .......................................................................................30

8.11.3 CF_LOGO Command.....................................................................................30

8.11.4 CF_CEIL Command .......................................................................................30

8.11.5 CF_REAR Command .....................................................................................31

8.11.6 CF_RCODE Command ..................................................................................31

8.11.7 CF_LANG Command .....................................................................................31

8.11.8 CF_INPUTSEARCH Command .....................................................................32

8.11.9 CF_ON – STA Command ...............................................................................32

8.11.10 CF_P – MANE Command...........................................................................32

8.11.11 CF_P – MANETIME Command ..................................................................32

8.11.12 CF_FANSPEED Command ........................................................................33

8.11.13 CF_KEYDIS Command ..............................................................................33

8.11.14 CF_TERMINAL Command .........................................................................33

8.11.15 CF_FDEFAULT Command .........................................................................33

8.11.16 CF_LOGOCAPTURE Command ...............................................................34

8.11.17 CF_FANMODE Command..........................................................................34

9. Status Read Command ................................................................................................35

9.1 Format ....................................................................................................................35

9.2 Transfer Example ..................................................................................................35

9.3 Operation Condition .............................................................................................35

9.4 Image Status Read Command .............................................................................36

9.4.1 CR_BRIGHT Command .................................................................................36

9.4.2 CR_CONT Command.....................................................................................36

9.4.3 CR_COLOR Command ..................................................................................36

9.4.4 CR_TINT Command .......................................................................................36

9.4.5 CR_SHARP Command ..................................................................................36

9.4.6 CR_GAMMA Command .................................................................................37

9.4.7 CR_WBAL – R Command .............................................................................37

9.4.8 CR_WBAL – G Command .............................................................................37

9.4.9 CR_WBAL – B Command .............................................................................37

9.4.10 CR_COLTEMP Command..............................................................................37

9.4.11 CR_NZRED Command ..................................................................................38

9.4.12 CR_PROGV Command ..................................................................................38

9.4.13 CR_IMAGE Command ...................................................................................38

9.4.14 CR_IMGGMD Command................................................................................38

9.5 PC Adjust Status Read Command ......................................................................39

9.5.1 CR_FSYNC Command...................................................................................39

9.5.2 CR_TDOTS Command...................................................................................39

4/51


9.5.3 CR_CLAMP Command ..................................................................................39

9.5.4 CR_H – POS Command.................................................................................39

9.5.5 CR_V – POS Command.................................................................................40

9.5.6 CR_DDOTS Command ..................................................................................40

9.5.7 CR_DLINE Command ....................................................................................40

9.5.8 CR_PCSTORE Command .............................................................................40

9.5.9 CR_SETPCADJ Command............................................................................41

9.6 Video Status Read Command ..............................................................................41

9.6.1 CR_SERSYS Command ................................................................................41

9.7 Input Status Read Command...............................................................................42

9.7.1 CR_INPUT Command ....................................................................................42

9.7.2 CR_SOURCE Command ...............................................................................42

9.7.3 CR_INPUT_%1 Command.............................................................................42

9.7.4 CR_SYSTEM Command ................................................................................43

9.8 Screen Status Read Command............................................................................44

9.8.1 CR_SCREEN Command................................................................................44

9.8.2 CR_VSCALE Command..............................................................................44

9.8.3 CR_VPOS Command.....................................................................................44

9.8.4 CR_HSCALE Command ................................................................................44

9.8.5 CR_HPOS Command.....................................................................................45

9.8.6 CR_FLSCREN Command..............................................................................45

9.8.7 CR_TRUE Command .....................................................................................45

9.8.8 CR_ KYSTNMODE Command.......................................................................45

9.9 Lamp Status Read Command ..............................................................................46

9.9.1 CR_LAMPREPL Command ...........................................................................46

9.9.2 CR_LAMPMODE Command..........................................................................46

9.9.3 CR_PROJH Command ..................................................................................46

9.10 Sound Status Read Command ............................................................................47

9.10.1 CR_VOLUME Command ...............................................................................47

9.10.2 CR_MUTE Command.....................................................................................47

9.11 Setting Status Read Command ...........................................................................47

9.11.1 CR_BBACK Command ..................................................................................47

9.11.2 CR_DISP Command.......................................................................................47

9.11.3 CR_LOGO Command ....................................................................................47

9.11.4 CR_RCODE Command ..................................................................................48

9.11.5 CR_LANG Command.....................................................................................48

9.11.6 CR_INPUTSEARCH Command.....................................................................48

9.11.7 CR_ON-STA Command .................................................................................48

9.11.8 CR_P-MANE Command.................................................................................49

9.11.9 CR_P – MANETIME Command .....................................................................49

5/51


9.11.10 CR_FANSPEED Command........................................................................49

9.11.11 CR_KEYDIS Command ..............................................................................49

9.11.12 CR_TERMINAL Command.........................................................................49

9.11.13 FANMODE Command ................................................................................50

9.12 Other Status Read Command ..............................................................................50

9.12.1 CR_SIGNAL Command .................................................................................50

9.12.2 CR_VMUTE Command ..................................................................................50

9.12.3 CR_FREEZE Command.................................................................................50

9.12.4 CR_PTIMER Command .................................................................................50

9.12.5 CR_TEMPWARN Command..........................................................................51

9.12.6 CR_TEMPFAIL Command .............................................................................51

6/51


1. OverView

1.1 This Functional specification defines communication functions for LC-XB33 (0.6” XGA).

1.2 Compatible to Firmware Ver. 1.x of the projector.

2. Serial Interface Specification

2.1 Transfer Specification

Item

Synchronous System Asynchronous

Specification

Transmission Speed 9600 / 19200

Data Length 8 bit

Parity

Stop Bit

N/A

1

Flow Control N/A

Note1) Transmission Speed : initial setting value is 19200

Note2) Transmission Speed can be changed in service mode.

2.2 Connection

Dedicated serial cable must be used for a connection to a computer and a projector.

7/51


3. Notes for communication

3.1

Expand Serial Command is defined as one command / one line that starts with “C” and ends with carriage return (0x0D)

3.2

There are two types of commands: Functional Execution Command and Status Read Command.

- Example of Functional Execution Command:”CF_BRIGHT_032”[CR]

- Example of Status Read Command: “CR_RIGHT”[CR]

- Example of Control Switch Command: “PF_LANMODE_1”[CR]

Note) ”_” means a space

3.3

When it takes more than one second to receive one command, it is not executed.

When it takes more than one second to receive carriage return (0X0D) since the projector has received the first data “C”, it clears the information of buffer.

3.4

When the command pipelining, it must wait for 100ms till sending next command after the response.

(More than 100ms)

Command

PC → Projector

Projector → PC

“CF_BRIGHT_032” CR Next Command

“ 000” CR

Response

(A few ms - 5s)

3.4.1

When a computer sends next command before receiving a response, the projector may not operate properly.

3.4.2

Except when there is no response for more than 5 seconds.

3.5

It takes about 5 seconds for internal initialization after plugging in AC power. During this time it cannot process commands. Do not issue any command.

4. Name Definition

4.1

Data from a controller to a projector is represented as COMMAND, and data from a projector to a controller for the incoming command is represented as RESPONSE.

4.2

[CR] : Carriage Return Code

Command ends with cartridge return code.

Response command also ends with carriage return code.

4.3

_ : Space Code

All space Code is indicated by (_).

4.4

%1 : Parameter in Command

When there are some parameters, they are defined as %2, %3…

4.5

%%% : Error code returned from a projector

Acceptable: “000”.

Unacceptable: See [7. Error Code Table].

4.6

%a : Parameter in Response Command

When there are some parameters, they are defined as %b, %c…

8/51


5. Functional Execution Command Table

5.1 Image Command Table

Execute command

CF_BRIGHT_%1[CR]

CF_CONT_%1[CR]

CF_COLOR_%1[CR]

CF_TINT_%1[CR]

CF_SHARP_%1[CR]

CF_GAMMA_%1[CR]

CF_WBAL-R_%1[CR]

CF_WBAL-G_%1[CR]

CF_WBAL-B_%1[CR]

CF_COLTEMP_%1[CR]

CF_NZRED_%1[CR]

CF_PROGV_%1[CR]

CF_IMAGE_%1[CR]

CF_IMAGEADJ_%1[CR]

Item

Set Brightness value

Set Contrast value

Set Color value

Set Tint value

Set Sharpness value

Set Gamma value

Set White Balance Red value

Set White Balance Green value

Set White Balance Blue value

Set Color Temp. value

Set/Cancel Noise reduction

Set /Cancel Progressive Scan

Set Image mode

Reset/Store for Image Adjustment

5.2 PC Adjust Control Command Table

Execute command

CF_FSYNC_%1[CR]

CF_TDOTS_%1[CR]

CF_CLAMP_%1[CR]

CF_H-POS_%1[CR]

CF_V-POS_%1[CR]

CF_DDOTS_%1[CR]

CF_DLINE_%1[CR]

CF_PCSTORE_%1[CR]

CF_PCMODEFREE_%1[CR]

Item

Set Fine Sync value

Set Total Dots value

Set Clamp Value

Set Horizontal Position value

Set Vertical Position value

Set Display Dots value

Set Display Line value

Store the setting value in PC Adjust menu to Mode 1-5

Delete the registered value in Mode1-5 and return it to

Free status

5.3 Video Control Command Table

Execute command

CF_AVDDOTS_%1[CR]

CF_AVDLINE_%1[CR]

CF_AVHPOS_%1[CR]

CF_AVVPOS_%1[CR]

CF_AVSERV_%1[CR]

Item

Set AV Horizontal Resolution value

Set AV Vertical Resolution value

Set AV Horizontal Position value

Set AV Vertical Position value

Return the value set by command such as CF_AVDDOTS /

CF_AVDLINE to default value

5.4 Input Control Command Table

Execute command

CF_INPUT_%1[CR]

CF_SOURCE_%1[CR]

CF_INPUT_%1_%2[CR]

CF_SYSTEM_%1[CR]

Select Input

Select Input Source

Select Input and Source

Select System

Item

9/51

LCXB33 Expand Serial Command Functional Specifications

5.5 Screen Command Table

Execute command

CF_SCREEN_%1[CR]

CF_VSCALE_%1[CR]

CF_VPOS_%1[CR]

CF_HSCALE_%1[CR]

CF_HPOS_%1[CR]

Select Screen size

Set V Scale

Set V Position.

Set H Scale

Set H Position.

CF_DZCENT_%1[CR]

CF_KEYSTONE_%1[CR]

Cancel Digital Zoom mode

Set Keystone

CF_KYSTNMODE_%1[CR] Set Keystone Store mode

Item

5.6 Lamp Command Table

Execute command Item

CF_LAMPH_%1[CR] Reset total running time for each lamp

CF_LAMPMODE_%1[CR]

Select Lamp mode

5.7 Sound Command Table

Execute command

CF_VOLUME_%1[CR]

CF_MUTE_%1[CR]

Item

Set Volume value

Control ON/OFF of Sound Mute

5.8 Setting Command Table

Execute command Item

CF_BBACK_%1[CR]

CF_DISP_%1[CR]

CF_LOGO_%1[CR]

CF_CEIL_%1[CR]

CF_REAR_%1[CR]

CF_RCODE_%1[CR]

CF_LANG_%1[CR]

Set Blue Back function

Set Display function

Set Logo function

Set Ceiling function

Set Rear function

Select Remote Control Reception Code

Select language for OSD

CF_INPUTSEARCH_%1[CR] Set Input search function

CF_ON-STA_%1[CR]

CF_P-MANE_%1[CR]

Set Power ON Start function

Set Power management function

CF_P-MANETIME_%1[CR]

CF_FANSPEED_%1[CR]

CF_KEYDIS_%1[CR]

CF_TERMINAL_%1[CR]

CF_FDEFAULT_%1[CR]

Set Power management time

Select Fan Speed

Prohibit RC/KEY

Set Terminal terminal

Set the value to Factory Default

CF_LOGOCAPTURE_%1[CR] Capture a projected image

CF_FANMODE_%1[CR] Select Fan mode

10/51


6. Status Read Command Table

6.1 Image Status Read Command Table

Status read command

CR_BRIGHT[CR]

CR_CONT[CR]

CR_COLOR[CR]

CR_TINT[CR]

CR_SHARP[CR]

CR_GAMMA[CR]

CR_WBAL-R[CR]

CR_WBAL-G[CR]

CR_WBAL-B[CR]

CR_COLTEMP[CR]

CR_NZRED[CR]

CR_PROGV[CR]

CR_IMAGE[CR]

CR_IMGGMD[CR]

Item

Get Brightness value

Get Contrast value

Get Color value

Get Tint value

Get Sharpness value

Get Gamma value

White Balance Red value

White Balance Green value

White Balance Blue value

Get Color temperature setting value

Get Noise reduction setting status

Get Progressive scan setting status

Get Selected Image status

Get Image Gamma setting value

6.2 PC Adjust Status Read Command Table


CR_FSYNC[CR]

CR_TDOTS[CR]

CR_CLAMP[CR]

CR_H-POS[CR]

CR_V-POS[CR]

CR_DDOTS[CR]

CR_DLINE[CR]

CR_PCSTORE[CR]

CR_SETPCADJ[CR]

Item

Get Fine Sync setting value

Get Total Dots setting value

Get Clamp setting value

Get Horizontal Position setting value

Get Vertical Position setting value

Get Display Dots setting value

Get Display Line setting value

Get Free or Stored status for PC Adj. mode1-5

Get current PC signal for PC display status

6.3 Video Status Read Command Table


CR_SERSYS[CR]

Item

Get selected current signal. When in Auto mode, it returns a result by Auto detect.

6.4 Input Status Read Command Table


CR_INPUT[CR]

CR_SOURCE[CR]

CR_INPUT_%1[CR]

CR_SYSTEM[CR]

Item

Get selected Input status

Get selected source of currently selected Input

Get status of selected input and selected source

Get selected system status in Input mode

6.5 Screen Status Read Command Table


CR_SCREEN[CR]

CR_FLSCREN[CR]

CR_TRUE[CR]

CR_KYSTNMODE[CR]

CR_VSCALE[CR]

CR_VPOS[CR]

CR_HSCALE[CR]

CR_HPOS[CR]

Item

Get selected screen size

Get Full Screen mode setting status

Get True mode setting status

Get Keystone Store mode setting mode

Get a detail of V Scale setting

Get a detail of V Position setting

Get a detail of H Scale setting

Get a detail of H Position setting

11/51


6.6 Lamp Status Read Command Table


CR_LAMPREPL[CR]

CR_LAMPMODE[CR]

CR_PROJH[CR]

Item

Get the information for Lamp replacement time

Get Lamp Mode status

Get projector total running time

6.7 Sound Status Read Command Table

Status read command Item

CR_VOLUME[CR]

CR_MUTE[CR]

Get Volume value

Get Sound Mute setting status

6.8 Setting Status Read Command Table


CR_BBACK[CR]

CR_DISP[CR]

CR_LOGO[CR]

CR_RCODE[CR]

CR_LANG[CR]

CR_INPUTSEARCH[CR]

CR_ON-STA[CR]

CR_P-MANE[CR]

CR_P-MANEＴＩＭＥ[CR]

CR_FANSPEED[CR]

CR_KEYDIS[CR]

CR_TERMINAL[CR]

CR_FANMODE[CR]

Item

Get Blue Back setting status

Get Display setting status

Get Logo setting status

Get selected Remote Control Code

Get selected language

Get Input search setting status

Get ON Start setting status

Get Power management setting status

Get setting time for Power management

Get selected FAN CONTROL SPEED

Get RC/KEY prohibited status

Get Terminal setting status

Get selected Fan mode

6.9 Other Status Read Command


CR_SIGNAL[CR]

CR_VMUTE[CR]

CR_FREEZE[CR]

CR_PTIMER[CR]

CR_TEMPWARN[CR]

CR_TEMPFAIL[CR]

Item

Get Signal Status if there is a signal or not

Get No Show setting status

Get Freeze setting status

Get the operating status of Presentation Timer

Get Temperature Status if it is close to abnormal temperature

Get temperature when sensors approach abnormal temperature

12/51


7. Error Code Table

Error Code

?

000

Contents

-When the received data cannot be decoded

-Parameter determination error (digit number error, including invalid value, etc.)

Normal reception (No error)

101 The function is not available in the selected Mode

102

103

201

301

Selected value is out of range (Not reflected)

Command mismatched to Hardware (command for

Optional function which is not installed)

When reached upper or lower limit of increasing or decreasing data

Command cannot be executed during capturing display. Resend the command after a while

―――

302

303

―――

402

Command cannot be executed during PIN code operation. Resend the command after a while.

Note) These error codes are applied in Expand Command, not in Basic Command

13/51


8. Functional Execution Command

8.1 Format

1) PC issues commands in format as below:

Pattern1 : “CF_COMMAND” [CR]

Pattern2 : “CF_COMMAND_”%1 [CR]

CF_ : Header

COMMAND : Character line

%1 : Parameter (Character line)

_ : Space (To separate COMMAND and Parameter)

2) The projector decodes the received command and when it is ready to receive the next command, it returns the response.

“000” [CR] : (0x06, 0x0D) When receiving Functional Execution Command

“nnn” [CR] : Except “000” , when it is unable to execute command by any specific reason.

See Error Code Table for details

3) When the received data cannot be decoded, the projector returns “?” [CR]

8.2 Transfer Example

When setting projector’s total dots to 1344 by Expand Serial Command

PC → PJ: ”CF_TDOTS_1344” [CR]

PC ← PJ: “000”[CR] - - - - - - - - - - - Acceptable

8.3 Operation Requirements

Functional Execution Command is limited when the projector status is as below.

However, Status Read Command is effective even under these conditions.

Standby Mode

Projector Status

Processing Countdown

Available Functional Execution Command

C00: POWER ON

C00: POWER ON

(Terminates Countdown)

C01: POWER OFF

C02: POWER OFF

(Terminates Countdown)

N/A Processing Cooling down

Processing Cooling down due to Abnormal

Temperature

Abnormal Temperature

Processing Power Save / Cooling down

Processing Power Save

N/A

N/A

Power Failure

(For 60 seconds after Power Failure occurred) N/A

N/A

C00: POWER ON

C01: POWER OFF

Note:) When the projector receives the other command in this above status, it returns error code to show the status.

When the projector receives the following functional execution commands, OSD menu is closed except for pop-up menu

14/51


8.4 Image Command

8.4.1 CF_BRIGHT Command

Command "CF_BRIGHT_%1”[CR]

%1

"000~063” --------------- Directly select Brightness setting value

"UP” ----------------------- Current Brightness setting value + 1

"DN” ----------------------- Current Brightness setting value – 1

Details

Set Brightness value of user control

The value set by this command will not be saved to the projector. Therefore, when

ALL is OFF, the value returns to the original setting. (The value is held in Standby mode.)

This command is available in the normal Power ON status.

Response

Acceptable “000”[CR]

Unacceptable “Error Code”[CR]

8.4.2 CF_CONT Command

Command “CF_CONT_％1”[CR]

%1

“000~063” --------------- Directly select Contrast setting value

“UP” ----------------------- Current Contrast setting value + 1

“DN” ----------------------- Current Contrast setting value – 1

Details

Response

Set Contrast value of user control


ALL is OFF, the value returns to the original setting. (The value is held in Standby mode.)



Unacceptable "Error Code”[CR]

8.4.3 CF_COLOR Command

Command “CF_COLOR_%1”[CR]

%1

Details

Response

“000~063” ---------------- Directly select Color setting value

“UP” ------------------------ Current Color setting value + 1

“DN” ------------------------ Current Color setting value - 1

Set Color value of user control


ALL is OFF, the value returns to the original setting. (The value is held in Standby mode)




15/51


8.4.4 CF_TINT Command

Command “CF_TINT_%1”[CR]

%1

Details

Response

“000~063” --------------- Directly select Tint setting value

“UP” ----------------------- Current Tint setting value + 1

“DN” ----------------------- Current Tint setting value – 1

Set Tint value of user control


ALL is OFF, the value returns to the original setting. (The value is held in Standby mode)




8.4.5 CF_SHARP Command

Command “CF_SHARP_%1”[CR]

%1

Details

Response

“000~015” ---------------- Directly select Sharpness setting value

“UP” ------------------------ Current Sharpness setting value + 1

“DN” ------------------------ Current Sharpness setting value - 1

Set Sharpness value of user control


ALL is OFF, the value returns to the original setting (The value is held in Standby mode)




8.4.6 CF_GAMMA Command

Command “CF_GAMMA_%1”[CR]

%1

“000~015” ---------------- Directly set Gamma setting value

“UP” ------------------------ Current Gamma setting value + 1

“DN” ------------------------ Current Gamma setting value – 1

Details

Set Gamma value of user control




Response



16/51


8.4.7 CF_WBAL - Command

Command “CF_WBAL-%1_%2”[CR]

%1

%2

Details

Response

“Ｒ” --------------------- Red

“Ｇ” --------------------- Green

“Ｂ” --------------------- Blue

“000~063” ----------- Directly select Color value set by White Balance%1

“UP” ------------------- Current Color value set by White Balance%1 + 1

“DN” ------------------- Current Color value set by White Balance%1 - 1

Set Color value set by White Balance%1 of user control






8.4.8 CF_COLTEMP Command

Command “CF_COLTEMP_%1”[CR]

%1

“000” ------ Xlow

“001” ------ Low

“002” ------ Mid

“003” ------ High

Details

Set Color Temp. (Available only in the normal Power ON status)




Response



8.4.9 CF_PROGV Command

Command “CF_PROGV_%1”[CR]

%1

Details

Response

“FILM” -------- Select Progressive Mode FILM

“L1” ----------- Select Progressive Mode L1

“L2” ----------- Select Progressive Mode L2

“OFF” -------- Cancel Progressive scan

Set / cancel Progressive scan (Available only in the normal Power ON status)






17/51


8.4.10 CF_NZRED Command

Command “CF_NZRED_%1”[CR]

%1

Details

Response

“OFF” ------- Cancel Noise Reduction

“L1” --------- Noise Reduction for moving image

“L2” --------- Noise Reduction for still image

Noise Reduction based on frame correlation

Select L1 or L2 depending on motion detection

L2 is more effective in reducing noise than L1, however, L2 can have a blur in moving image



8.4.11 CF_IMAGE Command

Command “CF_IMAGE_%1”[CR]

%1

“DYNAMIC” ------ Dynamic (Fixed value to enable projection with a sharp, powerful picture tone)

“STAND” ---------- Standard (Image adjust value is set to factory default)

“REAL” ------------ Real (Fixed value to display graphic image with natural tone)

“CINEMA” -------- Cinema (Fixed value to focus on tone reproduction for movie)

“BLACKBOARD” – Blackboard (Fixed value to project image onto grren-colored blackboard)

“CUSTOM1” ----- Image1 (the value set and stored by a user)




Details

Response

Select Image Mode (Available only in the normal Power ON status)

Parameter “CUSTOM1” to “CUSTOM4” is the same as “Image1” to “Image4” displayed when selecting Image on OSD menu.

The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF.



8.4.12 CF_IMAGEADJ Command

Command “CF_IMAGEADJ_%1”[CR]

%1

Details

Response

“RST” ------- Reset Image adjustment

“STR1” ----- Store current Image adjustment to Image 1




Reset / store Image adjustment.

(Available only in the normal Power ON statement)

Parameter “STR1” to “STR4” is the same as “Image1” to “Image4” displayed when adjusting Image on OSD menu and selecting “Store”

The value stored to “Image1-4” is saved and its setting is effective even after ALL is OFF.



18/51


8.5 PC Adjust Control Command

8.5.1 CF_FSYNC Command

Command “CF_FSYNC_%1”[CR]

%1

“0000~0031” --------------- Directly select Fine Sync setting value

“UP” -------------------------- Current Fine Sync setting value + 1

“DN” -------------------------- Current Fine Sync setting value - 1

Details

Response

Set Fine Sync value of PC signal (Available only in the normal Power ON status)




Unacceptable “101”[CR] --- when Input for Video is selected

8.5.2 CF_TDOTS Command

Command “CF_TDOTS_%1”[CR]

%1

“nnnn~mmmm” --- Directly select Total Dots setting value

“nnnn” shows minimum value, it is current Display Dots value + Horizontal

Position value . “mmmm” shows maximum value, it depends on current input signal.

“UP” -------------- Current Total Dots setting value + 1

“DN” -------------- Current Total Dots setting value - 1

Details

Response

Set Total Dots of PC signal (Available only in the normal Power ON status)




Unacceptable “101”[CR] ---- when Input for Video is selected

8.5.3 CF_CLAMP Command

Command “CF_CLAMP_%1”[CR]

%1

Details

Response

“mmmm~nnnn” --- Directly select Clamp setting value

“nnnn” shows minimum value, fixed to “0001”.

“mmmm” shows maximum value, it depends on current input signal.

“UP” -------------- Current Clamp setting value + 1

“DN” -------------- Current Clamp setting value – 1

Set Clamp value of PC signal (Available only in the normal Power ON status)





19/51


8.5.4 CF_H – POS Command

Command “CF_H-POS_%1”[CR]

%1

Details

Response

“0000~nnnn” --- Directly select Horizontal Position setting value

“nnnn” shows maximum value, it is current Total Dots value - Display Dots value

“UP” -------------- Current Horizontal Position setting value + 1

“DN” -------------- Current Horizontal Position setting value - 1

Set Horizontal Position value of PC signal.

(Available only in the normal Power ON status)





8.5.5 CF_V – POS Command

Command “CF_V-POS_%1”[CR]

%1

“0000~nnnn” --- Directly select Vertical Position setting value

“nnnn” shows maximum value, it is current Total Line value - Display Line value

“UP” -------------- Current Vertical Position setting value + 1

“DN” -------------- Current Vertical Position setting value – 1

Details

Response

Set Vertical Position value of PC signal





Unacceptable “101”[CR] ---- When Input source is Video system

8.5.6 CF_DDOTS Command

Command “CF_DDOTS_%1”[CR]

%1

Details

Response

“0256~nnnn” --- Directly select Display Dots setting value

“nnnn” shows maximum value, it is current Total Dots value - Horizontal

Position value

Even number is available and when odd number is set, it is rounded out.

“UP” -------------- Current Vertical Position setting value + 2

“DN” -------------- Current Vertical Position setting value – 2

Set Display Dots value of PC signal





Unacceptable “101”[CR] ---- When Input for Video is selected

20/51


8.5.7 CF_DLINE Command

Command “CF_DLINE_%1”[CR]

%1

“0100~nnnn” --- Directly select Display Line setting value

“nnnn” shows maximum value, it is current Total Line value – Vertical

Position value

“UP” -------------- Current Display Line setting value + 1

“DN” -------------- Current Display Line setting value – 1

Details

Response

Set Display Line value of PC signal






8.5.8 CF_PCSTORE Command

Command “CF_PCSTORE_%1”[CR]

%1

“MODE1” ---- Store current PC Adjust status to Mode1





Details

Response

Store current PC Adjust status (each parameter status such as Total dots) to

Mode1~Mode5. This command operates the same as storing to Mode1-Mode5 in

PC Adjust MENU.




8.5.9 CF_PCMODEFREE Command

Command “CF_PCMODEFREE_%1”[CR]

%1

“MODE1” ---- Free Mode1





Details

Response

Delete the registered data in Mode1-Mode5 and turns it to Free status.

This command operates the same as turning Mode1-Mode5 to Free in PC Adjust

Menu.




21/51


8.6 Video Control Command

8.6.1 CF_AVDDOTS Command

Command “CF_AVDDOTS_%1”[CR]

%1

“UP” --------- Current setting value + 1

“DN” --------- Current setting value – 1

Details

Response

Set AV Horizontal Resolution value



When there is no signal, it returns “101”[CR]


Unacceptable “101”[CR] ---- When Input for Computer is selected

8.6.2 CF_AVDLINE Command

Command “CF_AVDLINE_%1”[CR]

%1

Details

Response



Set AV Vertical Resolution value





Unacceptable “101”[CR] ---- When Input for PC is selected

8.6.3 CF_AVHPOS Command

Command “CF_AVHPOS_%1”[CR]

%1



Details

Response

Set AV Horizontal Position value






8.6.4 CF_AVVPOS Command

Command “CF_AVVPOS_%1”[CR]

%1



Details

Response

Set AV Vertical Position value






22/51


8.6.5 CF_AVSERV Command

Command “CF_AVSERV_%1”[CR]

%1

Details

“RST”

Turn AV Horizontal/Vertical Resolution value set by commands such as

“CF_AVDDOTS” / ”CF_AVDLINE” to default value




Response



23/51


8.7 Input Control Command

8.7.1 CF_INPUT Command

Command “CF_INPUT_%1”[CR]

%1

“COMPUTER1” ------ Select Computer 1 Input

“COMPUTER2” ------ Select Computer 2 Input

“VIDEO” ---------------- Select Video Input

Details

Response

Select Input (Available only in the normal Power ON status)

The same operation as “INPUT” button of Projector or Remote Control.

Note1) When Input 2(Computer 2) is set to Monitor Out by Terminal setting, “101” is set even if trying to select Input 2.


Unacceptable “%%%”[CR]

8.7.2 CF_SOURCE Command

Command “CF_SOURCE_%1”[CR]

Input is 1

“ANALOG” --------- Select Analog Input

“YPBPR” ------------ Select Component

“SCART” ------------ Select Scart Input

%1 Input is 2 “ANALOG” ---------- Select RGB

Details

Response

Input is 3

“AUTO” -------------- Select Vide Auto mode

“VIDEO” ------------- Select Composite Video Input

“S−VIDEO” -------- Select S-Video Input

Select Source of currently selected Input


When Input specified by %1 is inappropriate for selected Input, the projector returns “101” and this command is not executed.



8.7.3 CF_INPUT_%1_%2 Command

Command “CF_INPUT_%1_%2”[CR]

%1

“COMPUTER1” ---- Select Computer 1 Input

“COMPUTER2” ---- Select Computer 2 Input

“VIDEO” -------------- Select Analog Input

%2

Details

Response

When %1 is COMPUTER1

“ANALOG” ----- Select Analog RGB Input

“YPBPR” -------- Select Component Input

“SCART” -------- Select SCART Input


“ANALOG” ------ Select Analog RGB Input

When %1 is VIDEO

“AUTO” ---------- Select Video Auto Mode

“VIDEO” --------- Select Video Input

“S-VIDEO” ------ Select S-Video Input

Select Input specified by %1 and also Source specified by %2




24/51


8.7.4 CF_SYSTEM Command

Command “CF_SYSTEM_%1”[CR]

Input is

Computer

“MODE1” ------------- Select Mode 1





%1

Details

Response

Input is

Video

“AUTO” -------------------------- Select System “Auto”

“NTSC” -------------------------- Select NTSC

“NTSC443” --------------------- Select NTSC4.43

“PAL” ----------------------------- Select PAL

“SECAM” ----------------------- Select SECAM

“PAL-M” ------------------------- Select PAL-M

“PAL-N” ------------------------- Select PAL-N

“1080I” -------------------------- Select 1080i

“1035I” -------------------------- Select 1035i

“720P” --------------------------- Select 720p

“575P” --------------------------- Select 575p

“480P” --------------------------- Select 480p

“575I” ---------------------------- Select 575i

“480I” ---------------------------- Select 480i

Select System of currently selected Input


When Input specified by %1 is inappropriate for selected Input, the projector returns “101”[CR] and the command is not executed

Note1) “NTSC” / ”NTSC4.43” / ”PAL” / ”SECAM” / ”PAL-M” / ”PAL-N” is available only when Input is VIDEO / S-VIDEO

Note2) “1080I” / ”1035I” / ”720p” / ”575P” / ”480P” / “575I” / “480I” is available only when Input is Y / Pb/Cb / Pr/Cr



25/51


8.8 Screen Control Command

8.8.1 CF_SCREEN Command

Command “CF_SCREEN_%1”[CR]

%1

Input is

Computer

Input is

Video

“NORMAL” ---------------------- Display 4:3

“WIDE” --------------------------- Select 16:9 display

“TRUE” --------------------------- Select True size

“FULL” --------------------------- Select Full size

“CUSTOM” -----------------------Select Custom size

“DZOOM_UP” ------ Expand image size with Digital Zoom

“DZOOM_DN” ------ Compress image size with Digital Zoom

“NORMAL” ---------------------- Display 4:3

“WIDE” --------------------------- Select 16:9 display

“Custom” ------------------------ Select Custom mode

Details

Select screen size (Available only in the normal Power ON status)

When Input specified by %1 is inappropriate for selected Input, the projector returns “101”[CR] and the command is not executed


Response

8.8.2 CF_VSCALE Command

Command “ＣＦ_SCALE_%1”[CR]

%1

Details

Response

“032”･･･ +32

“031”･･･ +31

：

“002”･･･ +2

“001”･･･ +1

“000”･･･ ±0

“-01”･･･ −1

“-02”･･･ −2

：

“-31”･･･ −31

“-32”･･･ −32

“UP”･････ Vscale setting value ＋１

“ＤＮ”･････ Vscale seting value −１

Set V Scale. (Available only in the normal Power ON status)



26/51


8.8.3 CF_VPOS Command

Command “ＣＦ＿ＶＰＯＳ＿％１”[CR]

%1

Detail

Response

“０１５”･･･ +15

“０１４”･･･ +14

：

“００２”･･･ +2

“００１”･･･ +1

“０００”･･･ ±0

“−０１”･･･ −1

“−０２”･･･ −2

：

“−１４”･･･ −14

“−１５”･･･ −15

“ＵＰ”･････ Vposition settein value ＋１

“ＤＮ”･････ Vposition setting value −１

Set V Position.(Available only in the normal Power ON status)

Available “000”[CR]

Unavailable “Error Code”[CR]

8.8.4 CF_HSCALE Command

Command “ＣＦ＿ＨＳＣＡＬＥ＿％１”[CR]

％１

Detail

Response

“０３２”･･･ +32

“０３１”･･･ +31

：

“００２”･･･ +2

“００１”･･･ +1

“０００”･･･ ±0

“−０１”･･･ −1

“−０２”･･･ −2

：

“−３１”･･･ −31

“−３２”･･･ −32

“ＵＰ”･････ Hscale setting value ＋１

“ＤＮ”･････ Hscale setting value −１

Set H Scale. (Available only in the normal Power ON status)

Available “000”[CR]


27/51


8.8.5 CF_HPOS Command

Command “ＣＦ＿ＨＰＯＳ＿％１”[CR]

％１

Detail

Response

“０１５”･･･ +15

“０１４”･･･ +14

：

“００２”･･･ +2

“００１”･･･ +1

“０００”･･･ ±0

“−０１”･･･ −1

“−０２”･･･ −2

：

“−１４”･･･ −14

“−１５”･･･ −15

“ＵＰ”･････ Hposition setting value ＋１

“ＤＮ”･････ Hposition setting value −１

Set H Position. (Available only in the normal Power ON status)

Available “０００”[CR]


8.8.6 CF_DZCENT Command

Command “CF_DZCENT_%1”[CR]

%1 ”CENT” ---- Cancel Digital Zoom (CENT : “CENTER”)

Details

Cancel Digital Zoom

(Available only in the normal Power ON status and Input for Computer is selected)

Response


Unacceptable “101”[CR] ------ when Input for Video is selected

8.8.7 CF_KEYSTONE Command

Command “CF_KEYSTONE_%1”[CR]

%1

Details

Response

“UP” ------------- Correct Keystone distortion to reduce upper part of image

“FUP” ----------- Correct Keystone distortion to reduce upper part largely

“DN” ------------- Correct Keystone distortion to reduce lower part of image

“FDN” ----------- Correct Keystone distortion to reduce lower part largely

“RST” ------------ Set Keystone OFF

Change Keystone distortion correction



Unacceptable

“Error Code”[CR]

“201”[CR] ----When reaches the Keystone correction limit or when reaches correction limit by 1 step with “FDN”/”FUP”

(command is not executed)

8.8.8 CF_KYSTNMODE Command

Command “CF_KYSTNMODE_%1”[CR]

%1

“STR” --------- Set Keystone store mode to Store

“RST” --------- Set Keystone store mode to Reset

Details Set Keystone store mode (Available only in the normal Power ON status)

Response



28/51


8.9 Lamp Command

8.9.1 CF_LAMPH Command

Command “CF_LAMPH_%1”[CR]

%1 “RST”

Details Reset lamp total running time (Available only in the normal Power ON status)

Response



8.9.2 CF_LAMPMODE Command

Command “CF_LAMPMODE_%1”[CR]

%1

“NORMAL” ------- Set lamp to Normal mode status

“ECO” ------------- Set lamp to 3L mode status

“AUTO” ----------- Set lamp to Auto mode status

Details

Response

Select Lamp Mode (Available only in the normal Power ON status)




8.10 Sound Command

8.10.1 CF_VOLUME Command

Command “CF_VOLUME_%1”[CR]

%1

“000-063” --------------------------- Directly select Volume setting value

“UP” --------------------------------- Current Volume setting value +1

“DN” --------------------------------- Current Volume setting value -1

Details

Response

Control Volume value (Available only in the normal Power ON status)

The same operation as Volume Up/Down with projector and RC, and directly select Volume setting value. When setting Volume value, the Sound Mute ON status is canceled just like RC operation. The value set by this command is stored in Projector.



8.10.2 CF_MUTE Command

Command “CF_MUTE_%1”[CR]

%1

“ON” ----------------------------- Set Sound Mute ON

“OFF” --------------------------- Set Sound Mute OFF

Details Control Sound Mute ON/OFF (Available only in the normal Power ON status)

Response



29/51


8.11 Setting Command

8.11.1 CF_BBACK Command

Command “CF_BBACK_%1”[CR]

%1

“ON” ----------------------------- Select Blue Back

“OFF” ---------------------------- Cancel Blue Back

Details

Response

Set / Cancel Blue Back (Available only in the normal Power ON status)




8.11.2 CF_DISP Command

Command “CF_DISP_%1”[CR]

%1

“ON” ----------------------------- Select Display

“OFF” ---------------------------- Cancel Display

“CNTDWNOFF” --------------- Count down OFF

Details

Set / Cancel Display (Available only in the normal Power ON status)


Response



8.11.3 CF_LOGO Command

Command “CF_LOGO_%1”[CR]

%1

Details

“OFF” ----------------------------- Cancel Logo display

“DEFAULT” ---------------------- Set Default Logo display

“USER” --------------------------- Set Captured Logo display

Set / Cancel Logo (Available only in the normal Power ON status)

The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF


Response

8.11.4 CF_CEIL Command

Command “CF_CEIL_%1”[CR]

%1

“ON” --------------------------- Select Ceiling

“OFF” ------------------------- Cancel Ceiling

Details

Response

Set / Cancel Ceiling (Available only in the normal Power ON status)

The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF



30/51


8.11.5 CF_REAR Command

Command “CF_REAR_%1”[CR]

%1

Details

Response

“ON” --------------------------- Select Rear

“OFF” ------------------------- Cancel Rear

Set/Cancel Rear (Available only in the normal Power ON status)

When Rear is ON, image is left/right reversed.

The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF



8.11.6 CF_RCODE Command

Command “CF_RCODE_%1”[CR]

%1

Details

Response

"001” --------------------------- Select Code1

"002” --------------------------- Select Code2

Select Code of Remote Control (Available only in the normal Power ON status)




8.11.7 CF_LANG Command

Command “CF_LANG_%1”[CR]

%1

Details

Response

“ENG” --------------------------- Select ENGLISH

“DEU” --------------------------- Select German

“FRA” --------------------------- Select French

“ITA” ----------------------------- Select Italian

“ESP” ---------------------------- Select Spanish

“POR” --------------------------- Select Portuguese

“NED” --------------------------- Select Dutch

“SVE” --------------------------- Select Swedish

“RUS” --------------------------- Select Russian

“CHI” ---------------------------- Select Chinese

“KOR” --------------------------- Select Korean

“JPN” --------------------------- Select Japanese

“FIN” ---------------------------- Select

Finnish

“POL” --------------------------- Select Polish

“HUN” -------------------------- Select

“ROM” -------------------------- Select

Hungarian

Romanian

Set language for OSD (Available only in the normal Power ON status)

The language set by this command is stored in EEPROM and its setting is effective after ALL is OFF.



31/51


8.11.8 CF_INPUTSEARCH Command

Command “ＣＦ＿ＩＮＰＵＴＳＥＡＲＣＨ＿％１”[CR]

％１

Detail

Response

“ＯＦＦ”･･････ Input search is not in operation.

“ＯＮ１” ･･････ Set Input search operation On1.

“ＯＮ２” ･･････ Set Input search operation On2.

Set an operation mode of Input search. (Available only in the normal Power ON status)


Available “０００”[CR]


8.11.9 CF_ON – STA Command

Command “CF_ON−STA_%1”[CR]

%1

Details

Response

“ON” --------------------------- Select Power On Start

“OFF” ------------------------- Cancel Power On Start

Set/Cancel Power ON Start (Available only in the normal Power ON status)




8.11.10 CF_P – MANE Command

Command “CF_P−MANE_%1”[CR]

%1

Details

Response

“OFF” ---------------------------------- Set Power Management OFF

“READY” ----------------------------- Set Power Management Ready

“SHUTDOWN” ---------------------- Set Power Management to Shut Down mode

Set/Cancel Power Management (Available only in the normal Power ON status)




8.11.11 CF_P – MANETIME Command

Command “CF_P-MANETIME_%1”[CR]

％１

“01” - ”30” ----------------------- Directly select setting time by the minute

“UP” ------------------------------- Plus one minute

“DN” ------------------------------ Minus one minute

Details

Response

Set Power Management time (Available only in the normal Power ON status)




32/51


8.11.12 CF_FANSPEED Command

Command “CF_FANSPEED_%1”[CR]

％１

“MAX” ------------------------------ Select maximum fan speed

“NOR” ------------------------------ Select normal fan speed

Details

Response

Switch Fan Control Speed (Available only in the normal Power ON status)

The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF.



8.11.13 CF_KEYDIS Command

Command “CF_KEYDIS_%1”[CR]

%1

“NONE” ----------------------- RC & KEY are valid (All are valid)

“RC” ---------------------------- RC is invalid

“KEY” -------------------------- KEY is invalid

Details Set a ban on the use of RC/KEY (Available only in the normal Power ON status)

Response



8.11.14 CF_TERMINAL Command

Command “CF_TERMINAL_%1”[CR]

%1

“COMPUTER” --------------------- Set Input mode

“MONITOR” ------------------------ Set Monitor Out mode

Details

Response

Set Terminal (Available only in the normal Power ON status)

Terminal for Computer input is Computer 2 in this model.


Unacceptable


When Input is Computer 2, the projector returns “101” and the command is not executed

8.11.15 CF_FDEFAULT Command

Command “CF_FDEFAULT_%1”[CR]

%1 “RST”

Details

Response

Set the value to Factory Default (Available only in the normal Power ON status)

The same operation as Factory Default of user menu.



33/51


8.11.16 CF_LOGOCAPTURE Command

Command “CF_LOGOCAPTURE_%1”[CR]

%1 “START” --------------------------- Capture ON

Details

Capture projected image on screen.

Once capturing image is started, the command cannot be executed until capturing image is terminated. When the command is sent during this time, the projector returns error code “301”


Response

8.11.17 CF_FANMODE Command

Command “CF_FANMODE_%1”[CR]

%1

“L1” -------------------------------------- Select Fan Mode L1

“L2” -------------------------------------- Select Fan Mode L2

Details

Response

Switch Fan Mode (Available only in the normal Power ON status)

When L1 is selected, fan noise after POWER OFF is louder.

When L2 is selected, fan noise after POWER OFF is more silent, however, fan rotates for a longer time than L1.

The status set by this command is stored in EEPROM and its setting is effective even after ALL is OFF.



34/51


9. Status Read Command

9.1 Format

1) PC issues commands in format as below:

“CR_Command” [CR]

Command : Character Line

2) When projector receives the appropriate command, it returns a character line as the required data

“000＿”%1 [CR]

%1: Required Data (Character Line. See [Basic Status Read Command Table])

3) When the received data cannot be decoded, the projector returns “?”[CR]

9.2 Transfer Example

Get total dots of projector by Expand Commands

PC → PJ: “CR_TDOTS” [CR]

PC ← PJ: “000_1344” [CR]

9.3 Operation Condition

Basically Status Read Commands should be always operated.

35/51


9.4 Image Status Read Command

9.4.1 CR_BRIGHT Command

Command “CR_BRIGHT”[CR]

Details Get Brightness value of user control

Response

Acceptable “000_％ａ”[CR]

%a “000”~“063”

Unacceptable “?”[CR]

9.4.2 CR_CONT Command

Command “CR_CONT”[CR]

Details Get Contrast value of user control

Response

Acceptable “000_％ａ”[CR]

%a “000”~“063”


9.4.3 CR_COLOR Command

Command “CR_COLOR”[CR]

Details Get Color value of user control

Acceptable “000_%a”[CR]

Response %a “000”~“063”


9.4.4 CR_TINT Command

Command “CR_TINT”[CR]

Details Get Tint value of user control


%a “000”~“063”

Response

Unacceptable

“Error Code”[CR] ------ When the command is invalid due to condition such as Input source

“?”[CR] --------------------- When unclear command is received

9.4.5 CR_SHARP Command

Command “CR_SHARP”[CR]

Details Get Sharpness value of user control


Response %a “000”~“015”


36/51


9.4.6 CR_GAMMA Command

Command "CR_GAMMA”[CR]

Details Get Gamma value of user control


Response %a “000”~“015”


9.4.7 CR_WBAL – R Command

Command "CR_WBAL-R”[CR]

Details Get White Balance Red value of user control


Response %a “000”~“063”


9.4.8 CR_WBAL – G Command

Command "CR_WBAL-G”[CR]

Details Get White Balance Green value of user control

Response


%a “000”~“063”


9.4.9 CR_WBAL – B Command

Command "CR_WBAL-B”[CR]

Details Get White Balance Blue value of user control

Response


%a “000”~“063”


9.4.10 CR_COLTEMP Command

Command "CR_COLTEMP”[CR]

Details Get Color Temp. setting value


Response %a

“000” ------------------------------ Xlow

“001” ------------------------------ Low

“002” ------------------------------ Mid

“003” ------------------------------ High

“ADJ” ------------------------------ Processing adjusting White Balance


37/51


9.4.11 CR_NZRED Command

Command “CR_NZRED”[CR]

Details Get Noise Reduction setting status

Acceptable “000_%1”[CR]

Response %1

“L1” -------- Set Noise Reduction for moving image

“L2” -------- Set Noise Reduction for still image

“OFF” ------ Cancel Noise Reduction


9.4.12 CR_PROGV Command

Command “CR_PROGV”[CR]

Details Get Progressive scan setting value


Response %a

“L1” ----------------- Set Progressive Mode L1

“L2” ----------------- Set Progressive Mode L2

“FILM” -------------- Set Progressive Model FILM

“OFF” --------------- Cancel Progressive scan


9.4.13 CR_IMAGE Command

Command “CR_IMAGE”[CR]

Details

Get image setting status

Required data “CUSTOM1” to “CUSTOM4” is the same as “Image1” to “Image4” displayed when selecting IMAGE on OSD menu


Response

%a

Unacceptable

“DYNAMIC” --------------------------------------- Dynamic

“STAND” ------------------------------------------- Standard

“REAL” --------------------------------------------- Real

“CINEMA” ----------------------------------------- Cinema

“BLACKBOARD” -------------------------------- Blackboard

“CUSTOM1”~”CUSTOM4” -------------------- Image1~4

“Error Code”[CR] ---- When the command is invalid due to condition such as Input source

“?”[CR] -------------------- When unclear command is received

9.4.14 CR_IMGGMD Command

Command "CR_IMGGMD”[CR]

Details Get Standard/ Real/Cinema of Image Gamma setting status

Response


%a

“DYN” ------------ Dynamic

“STD” ------------ Standard

“REL” ------------ Real

“CNM” ------------ Cinema

“BKB” ------------ Blackboard


38/51


9.5 PC Adjust Status Read Command

9.5.1 CR_FSYNC Command

Command "CR_FSYNC”[CR]

Details Get Fine Sync value

Response


%a “0000”~“0031”

Unacceptable

“Error Code”[CR] ----- When the command is invalid due to condition such as Input source

“?”[CR] -------------------- When unclear command is received

9.5.2 CR_TDOTS Command

Command “CR_TDOTS”[CR]

Details Get Total Dots value


Response

%a

“nnnn”~“mmmm”

(nnnn = Display Dots + Horizontal Position)

(mmmm= Maximum value depends on input signal)

Unacceptable

“Error Code”[CR] -------- When the command is invalid due to condition such as Input source

“?”[CR] ----------------------- When unclear command is received

9.5.3 CR_CLAMP Command

Command “CR_CLAMP”[CR]

Details Get Clamp value

Response


%a

“0001”~“nnnn”

(mmmm= Maximum value depends on input signal)

Unacceptable



9.5.4 CR_H – POS Command

Command “CR_H

-

POS”[CR]

Details Get Horizontal Position value


Response

%a

Unacceptable

“0000”~“nnnn”

(nnnn = Total Dots - Display Dots)



39/51


9.5.5 CR_V – POS Command

Command “CR_V

-

POS”[CR]

Details Get Vertical Position value

Response


%a

“0000”~“nnnn”

(nnnn = Total Line - Display Line)

Unacceptable



9.5.6 CR_DDOTS Command

Command “CR_DDOTS”[CR]

Details Get Display Dots value

Response


%a

“0256”~“nnnn”

(nnnn = Total Dots – Horizontal Position value)

Unacceptable



9.5.7 CR_DLINE Command

Command “CR_DLINE”[CR]

Details Get Display Line value

Response


%a

“0100”~“nnnn”

(nnnn = Total Line – Vertical Position value)

Unacceptable



9.5.8 CR_PCSTORE Command

Command “CR_PCSTORE”[CR]

Details

Get if MODE1 - MODE5 for PC Adjust are Free or Stored.

Each data consists of 5 bytes and each byte represents MODE1~MODE5 respectively. (F:Free S:Stored)

Response


Required

Data

“FFFFF” ----------- All Free

“SFFFF” ----------- MODE1 is Stored, others are Free

:

“FFFFS” ----------- MODE5 is Stored, others are Free

“SSSSS” ---------- All Stored


40/51


9.5.9 CR_SETPCADJ Command

Command “CR_SETPCADJ”[CR]

Details Get PC signal for current system


Response %1

"XGA1”

"1080I60”, “720P”

"MODE1”~”MODE5” …Etc.


9.6 Video Status Read Command

9.6.1 CR_SERSYS Command

Command “CR_SERSYS”[CR]

Details

Response

Get current selected signal

Returns auto-detect result in Auto mode

Only available when Input is video (N/A when Input is computer)


%a

“1080I60” -------------- 1080i 60Hz

“1080I50” -------------- 1080i 50Hz

“1035I”. ---------------- 1035i

“720P” ------------------ 720p

“575P” ------------------ 575p

“480P” ------------------ 480p

“575I” ------------- 575i (includes Composite signal such as PAL)

“480I” ------------- 480i (includes Composite signal such as NTSC)

“NO_SIGNAL” --------------- There is no signal

41/51


9.7 Input Status Read Command

9.7.1 CR_INPUT Command

Command “CR_INPUT”[CR]

Details Get selected INPUT No.

Response


%a

“COMPUTER1” ------- Computer1 Input is selected

“COMPUTER2” ------- Computer2 Input is selected

“VIDEO” ----------------- Video Input is selected


9.7.2 CR_SOURCE Command

Command “CR_SOURCE”[CR]

Details Get selected Source


Response

%1

Unacceptable

“ANALOG” ---------- Analog (RGB) Input is selected

“SCART” ------------- SCART is selected

“AUTO” --------------- Video Auto is selected

“VIDEO” -------------- Video Input is selected

“S-VIDEO” ----------- S-Video Input is selected

“YCBCR” ------------- Y,Pb/Cb,Pr/Cr Input is selected



9.7.3 CR_INPUT_%1 Command

Command "CR_INPUT_%1”[CR]

%1

“COMPUTER1” ------------------------ Select Computer 1 Input

“COMPUTER2” ------------------------ Select Computer 2 Input

“VIDEO” --------------------------------- Select Video Input

Details Get selected source of currently selected Input


Response %a


“ANALOG” ------------ Analog RGB is selected

“YPBPR” -------------- Component Mode status

“SCART” -------------- Scart Mode status


“ANALOG” ------------ Analog RGB Mode status

“OUT” ------------------ Monitor OUT Mode status

When %1 is VIDEO

“AUTO” ---------------- Video Auto is selected

“VIDEO” --------------- Composite Video Input is selected

“S-VIDEO” ------------ S-Video Input is selected


42/51


9.7.4 CR_SYSTEM Command

Command “CR_SYSTEM”[CR]

Details Get selected System


Input is

PC

Returns “101”

Response

%1

Input is

Video

Unacceptable

“AUTO” -------------------------------- Auto is selected

“NTSC” -------------------------------- NTSC is selected

“NTSC443” --------------------------- NTSC4.43 is selected

“PAL” ---------------------------------- PAL is selected

“SECAM” ----------------------------- SECAM is selected

“PAL-M” ------------------------------- PAL-M is selected

“PAL-N” ------------------------------- PAL-N is selected

“1080I” -------------------------------- 1080iHz is selected

“1035I” -------------------------------- 1035iHz is selected

“720P ---------------------------------- 720p is selected

“575P” --------------------------------- 575p is selected

“480P” --------------------------------- 480p is selected

“575I” ---------------------------------- 575i is selected

“480I” ---------------------------------- 480i is selected

“101”[CR] --------------- When Input for PC is selected

“?”[CR] --------------- When unclear command is received

43/51


9.8 Screen Status Read Command

9.8.1 CR_SCREEN Command

Command “CR_SCREEN”[CR]

Details Get selected screen image size

Response


%a

Input is

PC

“NORMAL” --------------- Select 4:3 screen, signal that cannot be adjusted to 16:9

“WIDE” -------------------- Select 16:9 screen (signal except 16:9)

“TRUE” -------------------- True size screen mode

“FULL” -------------------- Full screen mode

“Custom” ------------------Custom mode

When the screen is set to D.Zoom, returns the previous status

(NORMAL/WIDE)

Input is

Video

Unacceptable

“NORMAL” --------------- Select 4:3 screen, signal that cannot be adjusted to 16:9

“WIDE” -------------------- Select 16:9 screen (signal except 16:9)

“Custom” ------------------Custom mode

“Error Code”[CR] ------ When the command is invalid due to condition such as Input source

“?”[CR] --------------------- Command

9.8.2 CR_VSCALE Command

Comand “ＣR＿ＶＳＣＡＬＥ”[CR]

Detail Get a detail of V Scale setting .

Available “０００＿％１”[CR]

Response

％１

Unavailable

“−３２”∼“０３２”


9.8.3 CR_VPOS Command

Command “ＣR＿ＶＰＯＳ”[CR]

Detail Get a detail of V Position setting.

Response

Available

％１

“０００＿％１”[CR]

“−１５”∼“０１５”

Unavailable “Error code”[CR]

9.8.4 CR_HSCALE Command

Command “ＣR＿ＨＳＣＡＬＥ”[CR]

Detail Get a detail of H Scale setting.


Response

％１ “−３２”∼“０３２”


44/51


9.8.5 CR_HPOS Command

Command “ＣR＿ＨＰＯＳ”[CR]

Detail Get a detail of H Position setting.


Response

％１ “−１５”∼“０１５”


9.8.6 CR_FLSCREN Command

Command “CR_FLSCREN”[CR]

Details Get if screen size is set to Full Screen

Response


%a

“ON” ------------------------ Screen size is set to Full Screen

“OFF” ----------------------- Screen size is not set to Full Screen

Unacceptable

“Error Code”[CR] ------- When the command is invalid due to condition such as Input source

“?”[CR] ---------------------- Command

9.8.7 CR_TRUE Command

Command “CR_TRUE”[CR]

Details Get if screen size is set to True


Response

%a

Unacceptable

“ON” ------------------------ Screen size is set to True

“OFF” ----------------------- Screen size is not set to True

“Error Code”[CR] ------- When the command is invalid due to condition such as Input source

“?”[CR] ---------------------- Command

9.8.8 CR_ KYSTNMODE Command

Command “CR_KYSTNMODE”[CR]

Details Get Keystone Store Mode setting status


Response %a

“STR” ---------------------- Store mode is “Store”

“RST” ---------------------- Store mode is “Reset”

Unacceptable “?”[CR] ------------------ Command

45/51


9.9 Lamp Status Read Command

9.9.1 CR_LAMPREPL Command

Command “CR_LAMPREPL”[CR]

Details Get the information of Lamp Replacement time

Response


%1

“1Y” -------------------------- over lamp replacement time

“1N” -------------------------- inside lamp replacement time

“1” means the number of lamps

(1 lamp is used→ “1”)

“Y”/”N” means if it is time to replace lamp or not.

Example:

“1Y” ----------- 1 lamp is used and it is over lamp replacement time


9.9.2 CR_LAMPMODE Command

Command “CR_LAMPMODE”[CR]

Details Get Lamp Mode setting status


Response %1

“NORMAL” -------------- Lamp Mode is Normal

“ECO” -------------------- Lamp Mode is Eco

“AUTO” ------------------ Lamp Mode is Auto


9.9.3 CR_PROJH Command

Command “CR_PROJH”[CR]

Details Get total running time of Projector by hour (h)


Response %1 “0000000”~“9999999”

Unacceptable ?”[CR]

46/51


9.10 Sound Status Read Command

9.10.1 CR_VOLUME Command

Command “CR_VOLUME”[CR]

Details Get Volume value of user control

Response


%a “000”~“063”


9.10.2 CR_MUTE Command

Command “CR_MUTE”[CR]

Details Get sound mute setting status

Response


%a

“ON” -------------------------- Set Sound Mute ON

“OFF” ------------------------ Cancel Sound Mute


9.11 Setting Status Read Command

9.11.1 CR_BBACK Command

Command “CR_BBACK”(CR)

Details Get Blue Back setting status


Response %a

“ON” -------------------------- Set Blue Back

“OFF” ------------------------ Cancel Blue Back


9.11.2 CR_DISP Command

Command “CR_DISP”[CR]

Details Get Display setting status


Response %a

“ON” -------------------------- Set Display ON

“OFF” ------------------------ Cancel Display

“CNTDWN-OFF” ---------- Set Countdown OFF


9.11.3 CR_LOGO Command

Command “CR_LOGO”[CR]

Details Get Logo setting status


Response %1

“OFF” ------------------------------ Cancel Logo

“DEFAULT” ----------------------- Set Default Logo

“USER” ---------------------------- Set User Logo


47/51


9.11.4 CR_RCODE Command

Command “CR_RCODE”[CR]

Details Get selected Remote Control Code status


Response %a

“001” ------------------------------- Select Code1

“002” ------------------------------- Select Code2


9.11.5 CR_LANG Command

Command “CR_LANG”[CR]

Details Get selected language


Response %a

“ENG” -------------------------- English is selected

“DEU” -------------------------- German is selected

“FRA” -------------------------- French is selected

“ITA” --------------------------- Italian is selected

“ESP” -------------------------- Spanish is selected

“POR” -------------------------- Portuguese is selected

“NED” -------------------------- Dutch is selected

“SVE” -------------------------- Swedish is selected

“JPN” -------------------------- Japanese is selected

“CHI” -------------------------- Chinese is selected

“KOR” -------------------------- Korean is selected

“RUS” -------------------------- Russian is selected

“FIN” ---------------------------- Finnish is selected

“POL” --------------------------- Polish is selected

“HUN” -------------------------- Hungarian is selected

“ROM” -------------------------- Romanian is selected


9.11.6 CR_INPUTSEARCH Command

Command “CR_INPUTSEARCH”[CR]

Details Get Input search setting status


Response %a

“OFF” -------------------------- Off is selected

“ON1” -------------------------- On1 is selected

“ON2” -------------------------- On2 is selected


9.11.7 CR_ON-STA Command

Command “CR_ON-STA”[CR]

Details Get Power ON Start setting status


Response %a

“ON” -------------------------- Set Power ON Start

“OFF” ------------------------ Cancel Power ON Start


48/51


9.11.8 CR_P-MANE Command

Command “CR_P-MANE”[CR]

Details Get Power management setting status


Response %a

“OFF” -------------------------- Power Management is canceled

“READY” ---------------------- Power Management is Ready

“SHUTDOWN” -------------- Power Management is set to Shut

Down mode


9.11.9 CR_P – MANETIME Command

Command “CR_P-MANETIME”[CR]

Details Get time setting to start Power Management


Response %a “001”~”030” -----------------------1 minute to 30 minutes


9.11.10 CR_FANSPEED Command

Command “CR_FANSPEED”[CR]

Details Get selected Fan Control Speed


Response %a

“MAX” ------------------------ Fan Control Speed is Max

“NOR” ------------------------ Fan Control Speed is Normal


9.11.11 CR_KEYDIS Command

Command “CR_KEYDIS”(CR)

Details Get RC/KEY prohibit status (valid or invalid)


Response %a

“NONE” -------------------------- RC & KEY are valid

“RC” ------------------------------- RC is invalid

“KEY” ----------------------------- KEY is invalid


9.11.12 CR_TERMINAL Command

Command “CR_TERMINAL”(CR)

Details Get Terminal setting status


Response %a

“COMPUTER” ------------------ Computer Input Mode

“MONITOR” --------------------- Monitor Out Mode


49/51


9.11.13 FANMODE Command

Command “CR_FANMODE”[CR]

Details Get selected Fan mode


Response %a

“L1” ----------------------- Fan mode L1

“L2” ----------------------- Fan mode L2


9.12 Other Status Read Command

9.12.1 CR_SIGNAL Command

Command “CR_SIGNAL”(CR)

Details Get Signal status if there is signal or not

Response


%a

“ON” -------------------------- There is signal

“OFF” ------------------------- There is no signal


9.12.2 CR_VMUTE Command

Command “CR_VMUTE”[CR]

Details Get No Show setting status


Response %a

“ON” ---------- Set No Show, Display User Logo (My picture)

“OFF” --------- Cancel No Show


9.12.3 CR_FREEZE Command

Command “CR_FREEZE”(CR)

Details Get Freeze setting status


Response %a

“ON” --------------------------- Set Freeze

“OFF” -------------------------- Cancel Freeze


9.12.4 CR_PTIMER Command

Command "CR_PTIMER”[CR]

Details Get the operating status of Presentation Timer


Response %a

“ON” -------------------- Presentation timer is in operation

“STOP” ----------------- Presentation timer is paused

“OFF” ------------------- Presentation timer is not operated


50/51


9.12.5 CR_TEMPWARN Command

Command “CR_TEMPWARN”[CR]

Details

Get the temperature inside a projector if it is abnormal temperature or close to abnormal temperature

It is possible to get the status all at once with some sensors installed.

Acceptable “000_%a_%b_%c”[CR]

Response

%a

%b

%c

%a -------------------- Sensor 1 status

%b -------------------- Sensor 2 status

%c -------------------- Sensor 3 status

“W” ---- Approach or reach abnormal temperature

(dangerous temperature)

“S” ---- Far from abnormal temperature (safe temperature)

“N” ---- Sensor detects no abnormal temperature

[Example]

“S_W_S”[CR] means Sensor 1 detects safe temperature, Sensor

2 detects abnormal temperature and Sensor 3 detects safe temperature

Note) When the temperature difference between Sensor 1 and 3 reaches specific value, it is considered as temperature abnormality by the projector model. In this case, the 3rd data means if the temperature difference between Sensor 1 and 3 is dangerous state or not. The 3rd data means temperature abnormality due to Sensor 3

When abnormal temperature is not detected by sensor, “N” (No connection with temperature abnormality) is returned.


9.12.6 CR_TEMPFAIL Command

Command "CR_TEMPFAIL”[CR]

Details

Get the temperature inside a projector when abnormal temperature occurs.

It is possible to get the temperatures all at once with some sensors installed.

Acceptable “000_%a_%b_%c”[CR]

Response

%a

%b

%c

%a ------------------ Sensor 1 temp. (External temp.)

%b ------------------ Sensor 2 temp. (Internal temp.1)

%c ------------------ Sensor 3 temp. (Internal temp.2)

[Example]

“_31.5F”[CR]

“_” indicates a space. When the temperature sinks to -, the first character is “-” like “-05.5F”[CR]

The last character means the sensor’s status if it reaches abnormal temperature

Exceeding critical temp. ------------------------------ “F”

Temp. is safe -------------------------------------------- “S”

Sensor detects no critical temp.--------------------- “N”

The example shows that sensor 1 indicates 31.5 degrees and the temperature is abnormal.

When the temperature is safe, all data are represented as

“□000S”.

When the projector is reset, “□000S” is set, and every time abnormal temperature occurs, it renews the data and returns it.

In short, it only returns the renewed data of the latest abnormal temperature and the previous data is deleted.


51/51

No results