Sharp 21HS-50H Service manual

21HS-50H
SERVICE MANUAL
SEBD21HS50H01
Issued: 24th October 2001
GA-1E CHASSIS
PAL I SYSTEM COLOUR TELEVISION
MODEL
21HS-50H
In the interests of user safety (required by safety
regulations in some countries) the set should restored
to its original condition and only parts identical to
those specified should be used.
CONTENTS
ELECTRICAL SPECIFICATION.........................3
IMPORTANT SERVICING NOTES ...................4
CONTROLS & TERMINALS..............................5
SERVICE ADJUSTMENTS................................6
CHASSIS LAYOUT...........................................12
LED FLASHING CODE....................................13
PRINTED WIRING BOARDS...........................13
ICs ADDITIONAL INFORMATION...................18
SCHEMATIC DIAGRAM, WAVE FORMS........26
BLOCK DIAGRAM...........................................32
TROUBLESHOOTING TABLES......................34
PARTS LISTING.............................................37
SHARP CORPORATION This document has been published to
1
be used for after sales service only.
21HS-50H
SERVICE MANUAL UPDATE LOG SHEET
Technical Report No.
Technical Bulletin No.
Cause / Solution
Part No.
Page No.
Application
Data /Serial No.
Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc.
If only part number changes are required, just change part number directly the part number in the Parts Listing Section.
If you need more information, please refer to the Technical Report (Bulletin).
2
21HS-50H
ELECTRICAL SPECIFICATIONS
•Sound Carrier Trap...............................32.9MHz
•Power Input .......................220V-240 Volts AC 50Hz
•Power Consumption
Normal Operation....................................43W
Stand-by Operation...................................3W
•Adjacent Sound Carrier Trap.................40.9MHz
•Audio Power Output Rating ................4W x 2(MPO)
•Adjacent Picture Carrier Trap...............30.9MHz
Speaker................................16Ω 4W, 9 x 5 cm,2pcs
Convergence.........................Self Converging System
•Aerial Input Impedance
VHF/UHF..........................75 ohm Unbalanced
Focus....................................Bi-Potencial Electrostatic
Sweep Deflection...........................................Magnetic
•Tuning Ranges ............45.75MHz thru 855.25 MHz
VHF.............IR A - J
S1-S41 (HYPERBAND)
UHF.............I21 - I69 CH
•Picture Intermediate Frecuency..............38.9MHz
•White Level
Set the brightness control, with no signal connected, so that the CRT cathode current is 600mA. The maximum
correction applied to each cathode current to achieve a screen temperature of 8900 degrees K-20 MPCD should
not exceed 15% of its original value.
X
Y
0.290 ± 0.015
0.284 ± 0.015
Screen temperature
8900º K-20 MPCD
Specifications are subject to change without prior notice.
WARNING
The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug
and power receptacle, when servicing this chassis.
To prevent electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to
qualified service personnel.
3
21HS-50H
IMPORTANT SERVICING NOTES
Only qualified service personnel are allowed to carry out maintenance and repair of this receiver.
SERVICING OF HIGH VOLTAGE SYSTEM AND CRT
It is important that the static charge is removed from the high voltage system when carrying out work
on the receiver. This can be achieved by connecting a 10K resistor (with a suitably insulated lead) from
the CRT cavity connector to the CRT ground tag. This must be carried out with the AC supply disconnected from the receiver.
Note the following:
• The CRT in this receiver employs Integral Implosion Protection.
• If the CRT has to be changed it MUST be replaced with the correct type for continued safe
working
• DO NOT lift the CRT by its neck.
• When handing the CRT, ensure that shatterproof goggles are worn.
• Ensure that the CRT is discharge before handling.
X-RAY
This receiver is designed to keep any x-ray emission to an absolute minimum. Some fault conditions
and servicing procedures may produce potentially hazardous x-ray radiation levels. This is a problem
when in close proximity to the receiver for long periods of time. To reduce any risks associated with
this, please observe the following precautions:
1. When undertaking any servicing on this chassis, DO NOT increase the EHT to more than 30.5 KV,
(at a instantaneous beam current of 1300µΑ).
2. Ensure that during normal operation the EHT does not exceed 25.0 KV±1.5KV (at a beam current of
1100µΑ). This level has been preset in the factory. Always check that this level has not been exceeded after carrying out any repair on the receiver.
3. DO NOT replace the CRT with any other type than that specified in the parts listing as this may
cause excessive x-ray radiation.
BEFORE RETURNING THE RECEIVER TO THE CUSTOMER
In addition to the above checks, the following should also be carried out before returning the receiver
to the customer.
1. Inspect all the leads to ensure that they are dressed correctly and that they are not obstructed or
pinched by any other parts.
2. Ensure that all protective devices are in good condition. These will include nonmetallic control
knobs, insulating fish papers, cabinets backs, compartment covers or shields, mechanical insulators,
etc.
4
21HS-50H
Location of Controls
Remote Control
CALL (
)/CHILD LOCK (
Infrared Transmitter Window
Aim this window at the infrared sensor
on your TV set
) button
TV/VIDEO Select button
TV
POWER/STANDBY (
TV/VIDEO
VCR
Single/Double Entry button (
) button
Programme Select buttons
VOLUME UP (
)/DOWN (
) buttons
(
) Increases sound
(
) Decreases sound
(These are also used for menu set up)
3
COLOUR buttons
5
6
8
9
CHANNEL (PROGRAMME) UP (
)/
DOWN (
) buttons
(
) Selects next higher programme
(
) Selects next lower programme
(These are also used for menu
set up)
TV button (Teletext)
1
2
4
7
FLASHBACK (
) button
Returns to previously viewed
programme
0
CH
REVEAL (
CH
MENU
TV
) button (Teletext)
Sound Mode Select (
LIST
HOLD (
LIST Select button (Teletext)
26
) button
) button (Teletext)
SOUND MUTE (
) button
Text/Mix (
)
Select button (Teletext)
) button (Teletext)
VCR
STORE (
) button (Teletext)
CLOCK (
MENU button
CANCEL (
)
) button (Teletext)
INDEX (
CH
) button (Teletext)
GA006SA
HALF PAGE (
) button (Teletext)
RESET (
) button (Teletext)
TV/ VCR/ TEXT REMOTE CONTROL
TV Front
MENU
Power (
CH
) button
Channel Up (
Power/On Timer indicator
Volume Up (
Remote Control Sensor
)/Down (
)/Down (
) buttons
) buttons
Menu button
Euro-SCART 21-Pin Terminal
21-Pin EuroFor greater A/V enjoyment, various audio and video devices may be
connected via the Euro-SCART 21-Pin Terminal.
1.
2.
3.
4.
5.
6.
7.
Audio right output
Audio right input
Audio left output
Common earth for audio
Earth for blue
Audio left input
Blue input
8. Audio-video control
9. Earth for green
10. Not used
11. Green input
12. Not used
13. Earth for red
14. Not used
15. Red input
16. Red/Green/Blue
control
17. Earth for video
Audio: Stereo Input / Output.
5
18.
19.
20.
21.
Earth for video
VIDEO output
VIDEO input
Common earth
21HS-50H
SERVICE ADJUSTMENT
• SERVICE MODE FUNCTION
•
All required adjustments for servicing this TV set, may be done in “service mode”, excepting G2 and FOCUS.
HOW TO ACCESS THE SERVICE MODE
1.
Turn the receiver on and ensure that it is tuned into a test pattern.
2.
Turn the receiver off using the mains switch.
3.
Press the volume down and channel up buttons together. See Fig.1.
4.
Continue pressing the volume down and channel up buttons while turning
the mains on using the mains switch. See Fig.1.
5.
Keep pressing the volume down and channel up buttons until the picture appears.
6.
When <<SHARPX X VXX.XX>> appears on the screen, release the two buttons.
7.
The receiver is now in the service mode. See Fig. 2.
CH
MENU
3
4
Fig.1
To move between the various service mode functions, use the channel up and down buttons. See Fig. 3.
Use the volume buttons to change the data to the desired value. See Fig. 3.
The data will be stored automatically when exiting the service mode. To exit the service mode press the standby button
on the remote control or turn the receiver off with the mains switch.
•
•
•
Fig. 2
Fig. 3
SHARP X
X VXX.XX
STS0: XXXX XXXX
STS1: XXXX XXXX
STS2: XXXX XXXX
Adjustment
(Yellow)
6
XXXX:
XX:
Value
(Green)
21HS-50H
• SERVICE ADJUSTMENTS AND DATA LIST
The table below shows the various service mode positions, range of values and default value. The columns are headed
as follows.
Heading:
Description:
OSD
This is what will appear on the screen when at this position
Function
This is the description of the mode’s function
Range
This is the range of values that can be entered while in this mode
Initial
This is the initial value, i.e. just after changing the NVM
Default
This is the recommended default value for this mode
FIX/ADJ
If this is ADJ, then it may be necessary to adjust this value away from the default
No. OSD
Function
Range
Initial
Default
FIX/ADJ
1
AGC
AGC Take Over Point
0...63
14
14
ADJ
2
V-LIN
Vertical Slope [VS]
0...63
32
32
ADJ
3
V-AMP
Vertical Amplitude [VA]
0...63
32
32
ADJ
4
V-CENT
Vertical Shift [VSH]
0...63
32
32
ADJ
5
H-CENT
Horizontal shift [HS]
0...63
32
32
ADJ
6
H-CENT60
offset to H-CENT for60 Hz
0...31 data(-16..+15)
16
20
FIX
7
EW / /
Horizontal Parallelogram [HP]
0...63
32
32
FIX
8
HB
Horizontal Bow
0...63
32
32
FIX
9
S-COR
S-Correction [SC]
0...63
0
22
FIX
10
DRI-RS
White point Red Standard white temp.
0...63
32
42
ADJ
11
DRI-GS
White point Green Standard white temp. 0...63
32
42
ADJ
12
DRI-BS
White point Blue Standard white temp
32
42
ADJ
13
DRI-RW
White point Red Warm white temp.
0...32
16
16
FIX
14
DRI-GW
White point Green Warm white temp.
0...32
16
9
FIX
15
DRI-BW
White point Blue Warm white temp.
0...32
16
9
FIX
16
DRI-RC
White point Red Cold white temp.
0...32
16
9
FIX
17
DRI-GC
White point Green Cold white temp.
0...32
16
9
FIX
18
DRI-BC
White point Blue Cold white temp.
0...32
16
16
FIX
19
SUB-VOL
Max Volume
0...63
60
60
FIX
20
SUB-CON
Sub Contrast
0...63
63
63
FIX
21
SUB-COL
Sub Colour
0...63
32
25
FIX
22
SUB-BRI
Sub Brightness
0...63
32
34
FIX
23
TINT
Sub Tint
0...63
32
32
FIX
24
SUB-SHP
Sub Sharpness
0...63
32
11
FIX
0...63
7
21HS-50H
No. OSD
Function
Range
Initial
Default
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
0...63
0...99 or > 99 for none
0...15
0(L-BG),1(BG),2(I),3(DK)
0...63
0...63
0...15
0...15
0...15
0...15
0...15
0...15
0...15
0...15
0...15
0...15
0..255
0..127
0..127
0..127
0...3 data(1.2.4.8.)
0..15
30
255
15
1
0
0
0
12
15
12
8
8
4
8
4
8
115
25
72
0
2
0
30
255
0
2
0
10
5
4
8
8
8
8
4
8
4
8
109
25
72
90
1
0
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
47 DISP
Max Hotel Volume
Hotel Program number
OSD RGB Reference
Sound system for auto turning
Black Level off-set R [BLR]
Black Level off-set G [BLB]
Cathode Drive Level [CL]
Y-Delay time for PAL (TV) [YD]
Y-Delay time for SECAM (TV) [YD]
Y-Delay time for N443 (TV) [YD]
COLOUR OFFSET (PAL)
COLOUR OFFSET (SECAM)
COLOUR OFFSET (NTSC443)
SHARPNESS OFFSET(PAL)
SHARPNESS OFFSET(SECAM)
SHARPNESS OFFSET(NTSC443)
SCART volume
Prescaler SCART input
Prescaler FM/AM
Prescaler SCART input
AVC Decay
Time to set the AC-OFF
timer is in steps of 10minutes
Language or symbols
0
1
FIX
48
TXT-EUR
Teletext pan-European language
0
0
FIX
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
BKS
AVC
FFI
ACL
S-L
S-DK
S-I
S-BG
BLUE-BACK
VMC
HTL
BTSC
AV
FMWS
SM0
SM1
AGC0
AGC1
FOA-FE
FOB-FE
FOA-AV
FOB-AV
TXT
TXT-WE
FSL
HP2
CP
Black Stretch
Automatic Volume Control(AVL)
Fast Filter IF-PLL
Auto Colour Limit
Sound system L
Sound system DK
Sound system I
Sound system BG
Video mute at Ident loss
Video Mute at program/source Change
Hotel mode
Reduced FM demodulator Gain (for BTSC sig)
Number of external AV sources
FM Window Selection
Sound Mute bit 0
Sound Mute bit 1
IF AGC speed bit0
IF AGC speed bit1
Phi 1 time constant for FE(RF)
Phi 2 time constant for FE(RF)
Phi 1 time constant for AV
Phi 2 time constant for AV
Teletext
Teletext Western or Eastern characters
Forced V-SYNC slicing level
Sync of OSD
Charge pump
1
0
0
0
0
1
1
1
1
1
0
0
1
0
1
0
1
0
0
0
1
1
0
0
0
0
0
1
1
0
1
0
0
1
0
1
1
0
0
0
0
1
0
1
0
0
0
1
1
1
0
0
0
0
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
0
0
0
0
1
1
0
0
0
1
FIX
FIX
FIX
FIX
FIX
HTL-VOL
HTL-PRG
RGB
SEARCH-SYS
CUT-R
CUT-G
CDL
DL-PT
DL-ST
DL-4T
COL-OP
COL-OS
COL-O4
SHP-OP
SHP-OS
SHP-O4
SC-VOL
PRE-SC
PRE-FM
PRE-NICAM
AVC-DKY
AC-OFF-TIM
76 NICAM
77 IGR
78 AUTO
79 TXT-TGL
80 EVG
NICAM decoding enabled
IGR decoding enabled
Start auto tuning at POWER-ON
Function of TXT key
Enable Vertical Guard
8
0(symboles),
1(English),
2(French)
0 (teletext pan-european language)
1 (second language;cyrillic)
2(third language;Greek)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 for 1 AV or 1 for 2 AV
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (westem) or 1 (eastem)
0 (disable) or 1 (enable)
0 for Ph1 or 1 for Ph2
0 (fast tuning) or
1 (moderate speed tuning)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 (disable) or 1 (enable)
0 or 1
0 (disable) or 1 (enable)
FIX/ADJ
21HS-50H
• SCREEN ADJUSTMENT
1. G2 Adjustment
1.
Enter the service mode (see page 6).
2.
Use the channel up or channel down buttons to enter the << BLUE-BACK >>
function.
“9GF
3.
Set this to << BLUE-BACK: 0 >>, i.e. blue background is turned off.
4.
Turn the set off at the mains.
5.
Turn the set back on.
6.
Set the picture control settings to normal.
7.
Select the SCART input by pressing the TV/SCART button on the remote control. Do not connect an input to the SCART socket. A blank raster will appear.
8.
Connect an oscilloscope to TP851 on the CRT PWB. The waveform as in figure 4 should be displayed.
9.
Adjust the G2 control (screen voltage) so that the peak of this waveform is 3.0V
+/-0.1V above the zero volt line.
9
9
Fig. 4
10. Enter the service mode.
11. Turn the blue background function back on again - set << BLUUE-BACK: 1 >>.
12. Turn off the receiver using the mains button.
13. The G2 adjustment is now complete.
2. Focus Adjustment
1.
Receive a monoscope pattern signal at a level of 60 to 80 dBuV.
2.
Set the picture settings to normal.
3.
Adjust the focus potentiometer to obtain maximum definition.
• AGC ADJUSTMENT
1.
Tune the receiver into a colour bar signal on channel E-12.
2.
Set the RF generator to an output signal strength of 57dBuV (+/-1dBuV) –50 Ohms unbalanced.
3.
Connect an oscilloscope to TP201. TP201 is one end of R201.
4.
Enter the service mode (see page 6).
5.
Use the channel up and channel down buttons to enter the AGC mode.
6.
By using the volume up and the volume down buttons, adjust the AGC until the voltage on TP201 drops by 0.1V
to 0.3V below its maximum value.
7.
Change the input signal strength to 66-70dBuV and make sure that there is no noise apparent in the picture.
8.
Turn the receiver off at the mains, this will exit the service mode and store the adjustment.
9
21HS-50H
• GEOMETRY ADJUSTMENT PROCEDURE
To adjust the geometry, follow the procedure outlined below:
1.Tune the set into a Philips test pattern.
2.Enter the service mode as described on page 6.
3.Use the channel up or channel down buttons to enter the desired mode
4.Use the volume buttons to achieve correct setting.
5.When adjustments are complete, use the standby button to turn off the set. The adjustment values will be stored
at this point.
V-LIN
Adjust the vertical linearity control so that the picture centring is as shown in figure 5.
Fig. 5
V-AMP
Adjust the vertical amplitude control so that the picture overscans as shown in figure 6.
Fig. 6
V-CENT
Adjust the vertical centring control so that the picture is centred as shown in figure 7.
Fig. 7
H-CENT
Adjust the horizontal centring control so that the picture is centred as shown in figure 8.
Fig. 8
10
21HS-50H
•COLOUR ADJUSTMENT PROCEDURE
The following adjustments should only be carried out when the CRT or IC801 are replaced.
NOTES:
• This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 700
µA.
• The red value «DRI-RS» should be fixed to 42. (Refer to “How to access service mode” section).
• «DRI-GS» adjustment alters “Y” co-ordinate.
• «DRI-BS» adjustment alters “X” and “Y” co-ordinates.
ADJUSTMENT METHOD 1 (using the signal generator, varying the picture signal)
1.
2.
3.
4.
5.
Adjust G2.
Input a white pattern with burst signal from SCART.
Position the colorimeter in the centre of screen.
Adjusting input signal level, select a luminance of 70 nits.
Operate again in “service mode“ and select «DRI-GS» and/or «DRI-BS» locations to obtain colour co-ordinates:
X
0.290 ± 0.015
Y
0.284 ± 0.015
Screen temperature
8900º K-20 MPCD
6. Re-set the TV with the mains switch button to store the adjustment and exit service mode.
7. Check colour co-ordinates “X” and “Y” at 20 a 120 Nits. It may be necessary to repeat the same procedure to
obtain the above values.
ADJUSTMENT METHOD 2 (using the signal generator, with a fixed picture signal)
1.
2.
3.
4.
5.
Adjust G2.
Tune a white pattern with burst signal.
Operate in “service mode”:
Using «SUB-CON», select a luminance of 70 nits.
Operate again in “service mode“ and select «DRI-GS» and/or «DRI-BS» locations to obtain colour co-ordinates:
X
0.290 ± 0.015
Y
0.284 ± 0.015
Screen temperature
8900º K-20 MPCD
6. Select «SUB-CON». Return data to “63”.
7. Re-set the TV with the mains switch button to store the adjustment and exit service mode.
8. Check colour co-ordinates “X” and “Y” at 20 a 120 Nits. It may be necessary to repeat the same procedure to
obtain the above values.
11
21HS-50H
CHASSIS LAYOUT
MOTHER UNIT
CRT UNIT
12
21HS-50H
LED FLASHING CODE
The led indicates the power mode,ocurred I2C error and On timer
PURPOSE:
INPUT:
- Current power mode
- I2C Errors
- On timer
Processing:
- If in STANDBY mode and On timer in-active then switch LED off.
- If in STANDBY and On timer active
set LED to blinking, (switch on and off at 1 Hz with a 50 % duty cycle).
- If in POWER-ON mode, switch LED on.
- If an I2C error occurred, let the LED blink at 1 Hz, 50 % duty cycle.
For the blinking times see the Table below.
Note:
Only when an I2C error occurs for a number of times, or for a number of seconds,
the I2C error is handled by the system (that is ,only then the set will go to standby,
the led starts blinking).
IC/Module Name
Slave Address
Bus Error LED Remarks
Blinking Time
M24C04
A0,A2
TDA935x/6x/8x
8A
VTST6HD64 or
C0
CTF551
C0
MSP34x5G
80
Table Error LED blinking times
2
3
6
6
5
Ref. No.
512x8 EEPROM
Address of internal TV processor
PLL Tuner
IC1002
IC801
TU201
Multistandard Sound Processor
IC3001
F 7341N0 PRINTED WIRING BOARD. Components side.
6
5
4
3
2
1
Y
0
X
1
2
3
4
5
13
6
7
8
9
10
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Components side.
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 15
2
1
Y
0
X
1
2
3
4
5
6
7
14
8
9
10
11
12
13
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Components side.
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
Page 14
3
2
1
Y
12
13
14
15
16
17
18
19
15
20
21
22
23
24
25
X
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Copper side.
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 17
2
1
Y
25 X
24
23
22
21
20
19
18
16
17
16
15
14
13
12
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Copper side.
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
Page 16
3
2
1
Y
13
12
11
10
9
8
7
6
17
5
4
3
2
0
1
X
21HS-50H
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
QUICK REFERENCE DATA
SYMBOL
PARAMETER
MIN.
TYP.
MAX.
UNIT
Supply
VP
supply voltages
−
8.0/3.3
−
V
IP
supply current
−
135/60
−
mA
ViVIFrms)
video IF amplifier sensitivity (RMS value)
−
75
−
µV
ViSIF(rms)
QSS sound IF amplifier sensitivity (RMS value)
−
60
−
µV
Input voltages
ViAUDIO(rms)
external audio input (RMS value)
−
500
−
mV
ViCVBS(p-p)
external CVBS/Y input (peak-to-peak value)
−
1.0
−
V
ViCHROMA(p-p)
external chroma input voltage (burst amplitude)
(peak-to-peak value)
−
0.3
−
V
ViRGB(p-p)
RGB inputs (peak-to-peak value)
−
0.7
−
V
ViYIN(p-p)
luminance input signal (peak-to-peak value)
−
1.4
−
V
ViUVIN(p-p)
U/V input signal (peak-to-peak value)
−
1.33/1.05 −
V
Output signals
mA
−
mA
IoEWD
EW drive output current
1.2
−
−
mA
45
44
43
42
41
40
39
38
37
36
35
34
33
20
21
22
23
24
25
26
27
28
29
30
31
32
IFIN2
IREF
MXXxxx
46
19
FBISO
HOUT
47
18
BCLIN
48
XXX
49
50
51
52
53
54
55
58
59
60
61
AVL/SNDIF/
REFO/AMOUT
SNDPLL/SIFAGC
GND2
AUDEEM/SIFIN1
DECSDEM/SIFIN2
TUNERAGC
VSC
IFIN1
VDRB
VDRA
AVL/EWD
DECBG
GND3
17
PH1LF
16
PH2LF
15
DECDIG
VP2
14
13
11
P0.6
SECPLL
10
P0.5
12
9
VSSC/P
VSSA
8
P3.3/ADC3/PWM3
7
P3.2/ADC2/PWM2
6
P3.1/ADC1/PWM1
5
P3.0/ADC0/PWM0
P2.0/TPMW
4
P1.6/SCL
3
2
P1.7/SDA
1
handbook, halfpage
P1.3/T1
TDA935X/6X/8X PS/N2
18
Fig. 3 Pin configuration (SDIP 64)
−
−
EHTO
AUDEXT/QSSO/
AMOUT
−
1
PLLIF
10
vertical output current (peak-to-peak value)
IFVO/SVO
horizontal output current
IoVERT
VP1
IoHOUT
CVBSINT
V
GND1
−
CVBS/Y
2.0
CHROMA
−
AUDOUT/AMOUT
RGB output signal amplitudes (peak-to-peak value)
R2/VIN
VoRGB(p-p)
INSSW2
mA
G2/YIN
5
B2/UIN
−
BLKIN
0
RO
tuner AGC output current range
GO
Io(AGCOUT)
BO
mV
VDDA
−
VPE
500
VDDC
−
OSCGND
Vo(AMOUT)(rms) demodulated AM sound output in QSS versions (RMS
value)
56
mV
XTALIN
−
57
100
XTALOUT
−
RESET
sound IF intercarrier output in QSS versions (RMS value)
VDDP
Vo(QSSO)(rms)
P1.0/INT1
V
P1.1/T0
−
62
2.5
P1.2/INT0
−
63
demodulated CVBS output (peak-to-peak value)
64
Vo(IFVO)(p-p)
42
40
24
19
+8V
37
38
15
19
14
39
18
41
30
SNDIF
REF
VIDEO FILTERS
VIDEO IDENT.
VIDEO SWITCH
VISION IF
ALIGNMENT-FREE
PLL DEMOD.
AGC/AFC
VIDEO AMP.
27
17
H-OSC. + PLL
H/V SYNC SEP.
PAL/SECAM/NTSC
DECODER
(32)
13
CHROMA 43
CVBS/Y
IFIN
23
TUNERAGC
AUDEXT
35
34
H-SHIFT
16
2nd LOOP
H-DRIVE
DELAY LINE
BASE-BAND
AGC CIRCUIT
NARROW BAND
PLL
DEMODULATOR
AUDOUT
V
44
HOUT
33
AUDIO SWITCH
(AVL)
VOLUME CONTROL
DEEMPHASIS
(20) 29 28
(32)
VPE
25
26
21
V-DRIVE
22
GEOMETRY
V-DRIVE +
LUMA DELAY
PEAKING
BLACK STRETCH
ROM/RAM
80C51 CPU
36
CVBS
LED OUT (2x)
EHTO
58 57
ENHANCED
60 55 59
3
4
5-8
ADC IN (4x)
VST OUT
I/O PORTS (4x)
EWD
(20)
(EW GEOMETRY)
SYNC
ACQUISITION
TELETEXT
I/O PORTS
VST PWM-DAC
I2C-BUS
TRANSCEIVER
2
1+62-64
RESET
V
U
Y
MEMORY
1/10 PAGE
54 56 61
G
B BL
B0
BCLIN
BLKIN
49
50
WHITE-P. ADJ.
R/V G/Y B/U BL
46 47 48 45
SATURATION
YUV/RGB MATRIX
RGB/YUV MATRIX
RGB/YUV INSERT
R G B
GO
53
RO
51
OSD/TEXT INSERT
CCC
CONTR/BRIGHTN
R
DISPLAY
TELETEXT/OSD
12
+3.3 V
52
COR
V
H
9
Block diagram TDA935X/6X8X PS/N2 with mono intercarrier sound demodulator
H
REF
(32) 31
SCL SDA
10/11
SOUND
TRAP
21HS-50H
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
BLOCK DIAGRAM
21HS-50H
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
PINNING
SYMBOL
PIN
DESCRIPTION
P1.3/T1
P1.6/SCL
P1.7/SDA
P2.0/TPWM
P3.0/ADC0/PWM0
P3.1/ADC1/PWM1
P3.2/ADC2/PWM2
P3.3/ADC3/PWM3
VSSC/P
P0.5
P0.6
VSSA
SECPLL
VP2
DECDIG
PH2LF
PH1LF
GND3
DECBG
AVL/EWD (1)
VDRB
VDRA
IFIN1
IFIN2
IREF
VSC
TUNERAGC
AUDEEM/SIFIN1(1)
DECSDEM/SIFIN2(1)
GND2
SNDPLL/SIFAGC(1)
AVL/SNDIF/REF0/
AMOUT(1)
HOUT
FBISO
AUDEXT/
QSSO/AMOUT(1)
EHTO
PLLIF
IFVO/SVO
VP1
CVBSINT
GND1
CVBS/Y
CHROMA
AUDOUT /AMOUT(1)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
port 1.3 or Counter/Timer 1 input
port 1.6 or I2C-bus clock line
port 1.7 or I2C-bus data line
port 2.0 or Tuning PWM output
port 3.0 or ADC0 input or PWM0 output
port 3.1 or ADC1 input or PWM1 output
port 3.2 or ADC2 input or PWM2 output
port 3.3 or ADC3 input or PWM3 output
digital ground for µ-Controller core and periphery
port 0.5 (8 mA current sinking capability for direct drive of LEDs)
port 0.6 (8 mA current sinking capability for direct drive of LEDs)
analog ground of Teletext decoder and digital ground of TV-processor
SECAM PLL decoupling
2nd supply voltage TV-processor (+8V)
decoupling digital supply of TV-processor
phase-2 filter
phase-1 filter
ground 3 for TV-processor
bandgap decoupling
Automatic Volume Levelling /East-West drive output
vertical drive B output
vertical drive A output
IF input 1
IF input 2
reference current input
vertical sawtooth capacitor
tuner AGC output
audio deemphasis or SIF input 1
decoupling sound demodulator or SIF input 2
ground 2 for TV processor
narrow band PLL filter /AGC sound IF
Automatic Volume Levelling / sound IF input / subcarrier reference output /AM output
(non controlled)
horizontal output
flyback input/sandcastle output
external audio input /QSS intercarrier out /AM audio output (non controlled)
36
37
38
39
40
41
42
43
44
EHT/overvoltage protection input
IF-PLL loop filter
IF video output / selected CVBS output
main supply voltage TV-processor (+8 V)
internal CVBS input
ground 1 for TV-processor
external CVBS/Y input
chrominance input (SVHS)
audio output /AM audio output (volume controlled)
20
21HS-50H
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
SYMBOL
INSSW2
R2/VIN
G2/YIN
B2/UIN
BCLIN
BLKIN
RO
GO
BO
VDDA
VPE
VDDC
OSCGND
XTALIN
XTALOUT
RESET
VDDP
P1.0/INT1
P1.1/T0
P1.2/INT0
PIN
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
DESCRIPTION
2nd
RGB / YUV insertion input
2nd R input / V (R-Y) input
2nd G input / Y input
2nd B input / U (B-Y) input
beam current limiter input / (V-guard input, note 2)
black current input / (V-guard input, note 2)
Red output
Green output
Blue output
analog supply of Teletext decoder and digital supply of TV-processor (3.3 V)
OTP Programming Voltage
digital supply to core (3.3 V)
oscillator ground supply
crystal oscillator input
crystal oscillator output
reset
digital supply to periphery (+3.3 V)
port 1.0 or external interrupt 1 input
port 1.1 or Counter/Timer 0 input
port 1.2 or external interrupt 0 input
Note
1. The function of pin 20, 28, 29, 31, 32, 35 and 44 is dependent on the IC version (mono intercarrier FM demodulator
/ QSS IF amplifier and East-West output or not) and on some software control bits. The valid combinations are given
in table 1.
2. The vertical guard function can be controlled via pin 49 or pin 50. The selection is made by means of the IVG bit in
subaddress 2BH.
Table 1
Pin functions for various versions
IC version
FM-PLL version
QSS version
East-West Y/N
N
Y
N
Y
CMB1/CMB0 bits
00
01/10/11
00
01/10/11
00
01/10/11
00
01/10/11
AM bit
−
−
−
−
−
0
1
−
0
1
Pin 20
AVL
EWD
AVL
EWD
Pin 28
AUDEEM
SIFIN1
Pin 29
DECSDEM
SIFIN2
Pin 31
SNDPLL
SIFAGC
REFO(2)
AMOUT
REFO(2)
Pin 32
SNDIF(1) REFO(2) AVL/SNDIF(1) REFO(2) AMOUT
Pin 35
AUDEXT
AUDEXT QSSO AMOUT AUDEXT QSSO AMOUT
Pin 44
AUDOUT
controlled AM or audio out
Note
1. When additional (external) selectivity is required for FM-PLL system pin 32 can be used as sound IF input. This
function is selected by means of SIF bit in subaddress 28H.
2. The reference output signal is only available for the CMB1/CMB0 setting of 0/1. For the other settings this pin is a
switch output (see also table 67).
21
21HS-50H
ICs ADDITIONAL INFORMATION:TEA1507(IC701)
ndbook, full pagewidth
VCC
1
SUPPLY
MANAGEMENT
8
START-UP
CURRENT SOURCE
clamp
internal UVLO start
supply
GND
2
S1
7
VALLEY
DRAIN
HVS
n.c.
M-level
4
VOLTAGE
CONTROLLED
OSCILLATOR
LOGIC
DEM
100 mV
OVERVOLTAGE
PROTECTION
FREQUENCY
CONTROL
OVERTEMPERATURE
PROTECTION
CTRL
LOGIC
6
DRIVER
DRIVER
Iss
3
−1
POWER-ON
RESET
S
Q
R
Q
LEB
blank
UVLO
2.5 V
0.5 V
soft
start
S2
5
OCP
burst
detect
short
winding
MAXIMUM
ON-TIME
PROTECTION
TEA1507
0.75 V
OVERPOWER
PROTECTION
MGU230
Block diagram.
PINNING
SYMBOL PIN
DESCRIPTION
VCC
1
supply voltage
GND
2
ground
CTRL
3
control input
DEM
4
input from auxiliary winding for
demagnetization timing, OVP and OPP
Isense
5
programmable current sense input
DRIVER
6
gate driver output
HVS
7
high voltage safety spacer, not
connected
DRAIN
8
drain of external MOS switch, input for
start-up current and valley sensing
handbook, halfpage
VCC 1
8 DRAIN
GND 2
7 HVS
TEA1507
CTRL 3
6 DRIVER
DEM 4
5 Isense
MGU231
Pin configuration.
22
Isense
21HS-50H
ICs ADDITIONAL INFORMATION:AN7523(IC303)
9
Volume
8
Pin Descriptions
N.C.
7
GND
6
Input
5
Standby
4
GND
Output
3
2
Output
VCC 1
Circuit Function Block Diagram
Pin No.
Description
1
Vcc
2
Ch Output (+)
3
GND
4
Ch Output (-)
5
Standby
6
Ch Input
7
GND (Input)
8
N.C
9
Volume
Note: Do not apply voltage or current to NC pin from outside
ICs ADDITIONAL INFORMATION:AN5522(IC501)
Pin Descriptions
Circuit Function Block Diagram
Thermal Protection
Amp
Pump Up
2
3
4
5
6
Vcc
Pump Up Out
GND
Output
Output Vcc
7
Non-inverting Input
1
Inverting Input
+
23
Pin No.
Pin Name
1
Inverting Input
2
Power Supply
3
Pump-up Output
4
GND
5
Vertical Output
6
Vertical Output Power Supply
7
Non-inverting Input
21HS-50H
ICs ADDITIONAL INFORMATION:MSP34x5G (IC3001)
Absolute Maximum Ratings
Symbol
Parameter
Pin Name
Min.
Max.
Unit
TA
Ambient Operating Temperature
–
0
70
°C
TS
Storage Temperature
–
−40
125
°C
VSUP1
First Supply Voltage
AHVSUP
−0.3
9.0
V
VSUP2
Second Supply Voltage
DVSUP
−0.3
6.0
V
VSUP3
Third Supply Voltage
AVSUP
−0.3
6.0
V
dVSUP23
Voltage between AVSUP
and DVSUP
AVSUP,
DVSUP
−0.5
0.5
V
PTOT
Package Power Dissipation
PSDIP64
PSDIP52
PQFP80
PLQFP64
PMQFP44
AHVSUP,
DVSUP,
AVSUP
1300
1200
1000
960
960
mW
mW
mW
mW
mW
−0.3
VSUP2+0.3
V
VIdig
Input Voltage, all Digital Inputs
IIdig
Input Current, all Digital Pins
–
−20
+20
mA1)
VIana
Input Voltage, all Analog Inputs
SCn_IN_s,2)
MONO_IN
−0.3
VSUP1+0.3
V
IIana
Input Current, all Analog Inputs
SCn_IN_s,2)
MONO_IN
−5
+5
mA1)
IOana
Output Current, all SCART Outputs
SC1_OUT_s2)
3) 4)
3) 4)
IOana
Output Current, all Analog Outputs
except SCART Outputs
DACM_s2)
3)
3)
ICana
Output Current, other pins
connected to capacitors
CAPL_M,
AGNDC
3)
3)
1)
2)
3)
4)
,
,
positive value means current flowing into the circuit
“n” means “1” or “2”, “s” means “L” or “R”
The Analog Outputs are short-circuit proof with respect to First Supply Voltage and Ground.
Total chip power dissipation must not exceed absolute maximum rating.
Stresses beyond those listed in the “Absolute Maximum Ratings” may cause permanent damage to the device. This
is a stress rating only. Functional operation of the device at these or any other conditions beyond those indicated in
the “Recommended Operating Conditions/Characteristics” of this specification is not implied. Exposure to absolute
maximum ratings conditions for extended periods may affect device reliability.
24
21HS-50H
ICs ADDITIONAL INFORMATION:MSP34x5G (IC3001)
NC
DACM_L
VREF1
DACM_R
SC1_OUT_R
SC1_OUT_L
VREF2
NC
NC
AHVSUP
NC
33 32 31 30 29 28 27 26 25 24 23
CAPL_M
34
22
RESETQ
AHVSS
35
21
I2S_DA_IN2
AGNDC
36
20
DVSS
SC2_IN_L
37
19
DVSUP
SC2_IN_R
38
18
ADR_CL
ASG
39
17
I2S_DA_IN1
SC1_IN_L
40
16
I2S_DA_OUT
SC1_IN_R
41
15
I2S_WS
VREFTOP
42
14
I2S_CL
MONO_IN
43
13
I2C_DA
AVSS
44
12
I2C_CL
MSP 34x5G
1
2
3
4
5
6
7
8
9
10 11
AVSUP
STANDBYQ
ANA_IN1+
ADR_SEL
ANA_IN−
D_CTR_I/O0
TESTEN
D_CTR_I/O1
XTAL_IN
TP
XTAL_OUT
PMQFP44 package
ADC
Demodulator
I2S1
Prescale
I2S2
Loudspeaker
Sound
Processing
Preprocessing
DAC
Source Select
Sound IF1
Loudspeaker
I2S
SCART1
DAC
SCART2
SCART
DSP
Input
Select
ADC
Prescale
SCART
Output
Select
MONO
Simplified functional block diagram of MSP 34x5G
25
SCART1
21HS-50H
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTE:
1. The unit of resistance «ohm»is omitted (K=1000
ohms. M= Megaohm).
2. All resistors are 1/16 watt. unless otherwise noted.
3. All capacitors are µF, unless otherwise noted (P=
µµF).
4. The capacitor with Part No. RC-FZ9XXXBMNJ is
designed to with stand 63V.
5. The capacitor with Part No. RC-FZ4XXXBMNJ is
designed to with stand 50V.
SAFETY NOTE:
1. DISCONNECT THE AC PLUG FROM THE AC
OUTLET BEFORE REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
IMPOTANT SAFETY NOTE:
PARTS MARKED WITH « ! » (
) ARE
IMPORTANT FOR MAINTAINING THE SAFETY
OF THE SET. BE SURE TO REPLACE THESE
PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE
SET.
SERVICE PRECAUTION:
THE AREA ENCLOSED BY THIS LINE (
)
IS DIRECTLY CONNECTED WITH AC MAINS
VOLTAGE.
WHEN SERVICING THE AREA, CONNECT AN
ISOLATING TRANSFORMER BETWEEN TV
RECEIVER AND AC LINE TO ELIMINATE
HAZARD OF ELECTRIC SHOCK.
CAUTION
This circuit diagram is original one,
therefore there may be slight difference
from yours.
WAVEFORM MEASUREMENT CONDITION:
Colour bar genetator signal of 70 dB from RF input.
WAVEFORMS:
26
21HS-50H
27
21HS-50H
SCHEMATIC DIAGRAM OF MOTHER UNIT (F7340N4, 01 Version)
I
H
G
F
E
D
C
B
Page 29
A
1
2
3
4
28
5
6
7
21HS-50H
SCHEMATIC DIAGRAM OF MOTHER UNIT (F7340N4, 01 Version)
I
H
G
F
E
D
C
B
Page 28
Page 30
A
8
9
10
11
29
12
13
14
21HS-50H
SCHEMATIC DIAGRAM OF MOTHER UNIT (F7340N4, 01 Version)
I
H
G
F
E
D
Page 29
C
B
A
8
9
10
11
30
12
13
14
21HS-50H
SCHEMATIC DIAGRAM OF CRT (F7341N0, 00 Version)
I
H
G
F
E
D
C
B
A
1
2
3
4
31
5
6
7
21HS-50H
CRT UNIT BLOCK DIAGRAM
I
H
G
F
E
D
C
B
A
1
2
3
4
32
5
6
7
21HS-50H
MOTHER UNIT BLOCK DIAGRAM
I
H
G
F
E
D
C
B
A
1
2
3
4
33
5
6
7
21HS-50H
TROUBLESHOOTING TABLES.
NO RASTER
Check F701.
Blown out.
Abnormal
Normal
Replace the fuse.
Check R701 Q701.
and IC701
Check T701 pin16 voltage.
(Approx. 290V at 220V AC)
The fuse is again blown out.
Check IC701,D701,D702,
D703,D704 and C705.
Normal
Abnormal
Check Secondary Main+B.
(Approx. 110V)
Check D758,IC702,IC753
and D762.
Check CRT connector K1K5 bias.
YES
Normal
Normal
Abnormal
Check R615.
Check
C878.
Check
IC801.
D1001 (Power LED Bright Red)
turns on.
NO
NO
D1001 (Power LED Dark Red)
turns on
Checking the
protector circuit.
D1001 turns on
brightly and darkly.
(Bus error)
NVM
(IC1002)
See many often D1001
flashes in red.
This indicates which IC to
check up.
Normal
TV PROCESSOR
(IC801)
SOUND PROCESSOR
(IC3001)
TUNER
(TU201)
34
21HS-50H
TROUBLESHOOTING TABLES.
NEITHER VERTICAL NOR
HORIZONTAL SYNCHRONIZATION
CIRCUIT TO BE CHECKED:
Sync. Separator Circuit.
Check pin33 and 34
of IC801.
DEFECTIVE VERTICEL AMP.
AND VERTICAL LINEARITY
Readjusted vertical size.
(Bass Data)
Vertical linearity and size
is abnormal.
Check R502,R505
NO VERTICAL SCAN
Check IC501 bias.
Normal
Abnormal
Check C502 and C514.
Check IC501.
NO SPECIFIC COLOUR
NO
YES
Is some colour produced in
B/W broadcast reception?
YES
Check IC801,R801,R802,
R803,D804,D805,D806
and Q801.
Is the white balance
properly adjusted?
NO
Readjusted the white
balance.
The picture colour is cyan.
The picture colour is magenta.
The picture colour is yellow.
Check Q870,Q885 and
their adjacent circuits.
Check Q871,Q883 and
their adjacent circuits.
Check Q872,Q887 and
their adjacent circuits.
35
21HS-50H
TROUBLESHOOTING TABLES.
NO PICTURE, NO SOUND
CIRCUITS TO BE CHECKED:
Tuner.
PIF.
Automatic Gain Control.
5V, 32V Power Source.
Does the noise level increase at max.
Contrast,Brightness and Sound controls?
Noise increase but no
signal is received.
No snow noise.
Check the tuner supply voltage
LB and HB must be approx. 5V,
BT must be approx. 32V,and
CH preset data check.
Does noise or signal appear
at pin40 of IC801?
NO
YES
Does noise or
signal appear at
pin38 of IC801?
Normal
NO
Check the tuner
AGC at TP201.
Normal
YES
Does noise or
signal appear at
pin23 and 24
of IC801?
Abnormal
NO
Check pin38
of IC801.
Check IC801
and its related
circuit.
Check pin27
of IC801,Tuner
and related circuit.
Check Q401
Q402 and related
circuit.
YES
Check pin1,2 of
SF201,Tuner
and related
circuit.
Check pin37 of
IC801 and
related circuit.
NO
SOUND
NO SOUND
CIRCUITS
TO BE
CIRCUITS
TOCHECKED:
BE CHECKED:
Audio
Output
Circuit.
Audio Output Circuit.
NO
NO
Doessignal
signal appear
appear
Does
at pin6 of IC303?
at pin6 of IC302/303?
YES
Check
IC801and
and
Check
IC3001
its related circuit.
its related circuit.
NO
YES
NO
Check Speaker.
Check Speaker.
Check IC303 and
peripheral
circuit.
Check IC302/303
and
peripheral circuit.
36
21HS-50H
PARTS LISTING
REPLACEMENT PARTS
Replacement parts which have special safety characteristics are identified in this manual. Electrical components having such features are identified by
in the Replacement Part List.
The use of a substitute replacement part which does not have the same
safety characteristics as the factory recommended is not permitted.
Replacement parts not shown in this service manual may create shock
fire, or other hazards.
HOW TO ORDER REPLACEMENT PARTS
To have your order completed promplty and corretly please supply the
following information.
1. MODEL NUMBER
3. PART NO.
5. CODE
2. REF. NO.
4. DESCRIPTION
6. QUANTITY
MARK *: SPARE PARTS DELIVERY SECTION
REF No. PARTS
DESCRIPTION
* SN CODE EX CODE
PICTURE TUBE
VB51EFS83912E
RCILG0408BMZZ
!
!
CRT 21" THA51EFS83X391+DYW S
DEGUSSING COIL TODAIMUSEN S
BN
AH
CD
AP
S
S
---
---
PRINTED WIRING BOARDS (Not replacement item)
DUNTK7340CJV3
DUNTK7341BMV3
PWB-A
ADJUST CHASSIS 21HS50H
CRT UNIT INS A 21HS50H
MOTHER UNIT
TUNER
TU 0201
VTUCTF5511+++
TUNER THOMSON
S
AA
AZ
IC 0303
IC 0501
IC 0601
IC 0701
IC 0702
IC 0751
IC 0801
IC 1002
IC 3001
VHIAN7523++-1
VHIAN5522++-1
VHIKA7808AP-1
VHITEA1507/-1
RH-FX0008GEZZ
VHITA48M033-1
RH-IXA096WJZZ
VHIM24C08W6-1
VHIMSP3415G-1
IC AN7523 MATSUSHITA
S
IC AN5523 MATSUSHITA
S
IC KIA7808API KOREA ELECTRONICS
IC TEA1507P/N1 PHILIPS
S
P/COUPLER RANK-S SHARP
S
IC TA48M033F(S) TOSHIBA
S
IC TDA9350 P/N TEXT 64K STEREO S
IC M24C08-WMN6T ST MICRO
S
IC
S
AC
AC
AA
AC
AA
AB
AA
AB
AA
AH
AG
AE
AH
AD
AF
BF
AF
BC
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
0331
0351
0352
0401
0402
0451
0501
0502
0601
0602
0603
0604
0605
0631
0701
0752
0753
0754
1005
1006
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2482//-1
VS2SD2586//1E
VS2SC2412KQ-1
VS2SC4793//-1
VS2SA1037KQ-1
VS2SA1037KQ-1
VSSTP4NC80Z1E
VS2SC1815GW-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
VS2SC2412KQ-1
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2482 TOSHIBA
TRT 2SD2586 TOSHIBA
TRT 2SC2412 ROHM
TRT C4793 TOSHIBA
TRT BC807 SMD
TRT BC807 SMD
MOS FET STP4NC80ZFP TOMEN
TRT NPN 60V 150MA 400MW
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
TRT 2SC2412 ROHM
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AR
AA
AE
AA
AA
AH
AA
AA
AA
AA
AA
D
D
D
D
D
D
D
0201
0303
0351
0451
0452
0453
0454
RH-EX0676GEZZ
RH-DX0045BMZZ
RH-EX1399CEZZ
RH-EX1399CEZZ
RH-EX1399CEZZ
RH-EX1399CEZZ
RH-EX1399CEZZ
ZENER DIODE MTZJ33CT ROHM S
DIODE 1N4148
S
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
INTEGRATED CIRCUITS
!
TRANSISTORS
REF No. PARTS
DESCRIPTION
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
* SN CODE EX CODE
0456
0457
0501
0502
0503
0504
0505
0507
0508
0509
0510
0601
0602
0603
0604
0605
0606
0607
0607
0608
0609
0610
0611
0612
0614
0615
0631
0632
0701
0702
0703
0704
0705
0708
0709
0751
0752
0753
0755
0756
0758
0759
0804
0805
0806
0807
1001
RH-EX1399CEZZ
RH-EX1399CEZZ
RH-DX0131CEZZ
RH-DX0441CEZZ
RH-EX0684GEZZ
RH-EX0684GEZZ
RH-DX0131CEZZ
RH-EX0603GEZZ
RH-DX0045BMZZ
RH-DX0045BMZZ
RH-EX0627GEZZ
RH-DX0302CEZZ
RH-DX0045BMZZ
RH-DX0131CEZZ
RH-DX0045BMZZ
RH-DX0045BMZZ
RH-DX0045BMZZ
RH-EX0652GEZZ
RH-EX0653GEZZ
RH-DX0577BMZZ
VHD1SS244//-1
RH-DX0045BMZZ
RH-EX0615GEZZ
RH-DX0045BMZZ
RH-DX0045BMZZ
RH-DX0045BMZZ
RH-EX0627GEZZ
RH-DX0045BMZZ
RH-DX0571BMZZ
RH-DX0571BMZZ
RH-DX0571BMZZ
RH-DX0571BMZZ
VHD1SS244//-1
RH-DX0045BMZZ
RH-EX0656GEZZ
RH-DX0302CEZZ
RH-DX0064GEZZ
RH-EX0612GEZZ
RH-DX0045BMZZ
RH-EX0615GEZZ
RH-DX0468CEZZ
RH-DX0045BMZZ
RH-EX1399CEZZ
RH-EX1399CEZZ
RH-EX1399CEZZ
RH-EX1399CEZZ
RH-PX0013PEZZ
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
DIODE EU-1 SANKEN
S
DIODE IN4002G23 GENERAL INSTRS
ZENER DIODE MTZJ39BT ROHM S
ZENER DIODE MTZJ39BT ROHM S
DIODE EU-1 SANKEN
S
Z.DIODE MTZJ 3.9A
S
DIODE 1N4148
S
DIODE 1N4148
S
ZENER DIODE MTZJ8.2BT ROHM S
DIODE UZA
S
DIODE 1N4148
S
DIODE EU-1 SANKEN
S
DIODE 1N4148
S
DIODE 1N4148
S
DIODE 1N4148
S
ZENER DIODE MTZJ18B ROHM
S
DIODE ZENER MTZJ18C ROHM
S
DIODE 1N4935 ACPA
S
SW DIODE 1SS244T-72
S
DIODE 1N4148
S
ZENER DIODE 5.6V
S
DIODE 1N4148
S
DIODE 1N4148
S
DIODE 1N4148
S
ZENER DIODE MTZJ8.2BT ROHM S
DIODE 1N4148
S
DIODE 1N4005 ACPA
S
DIODE 1N4005 ACPA
S
DIODE 1N4005 ACPA
S
DIODE 1N4005 ACPA
S
SW DIODE 1SS244T-72
S
DIODE 1N4148
S
ZENER DIODE MTZJ20C ROHM
S
DIODE UZA
S
DIODE AK04V1 SANKEN
S
ZENER DIODE MTZJ5.1BT ROHM S
DIODE 1N4148
S
ZENER DIODE 5.6V
S
DIODE S3L20U SHINDENGEN
S
DIODE 1N4148
S
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
ZENER DIODE UDZSTE-179.1B WAKS
LED L-53ID-13.95L/F
S
PR 0701
X 1001
X 3001
RMPTP0001BMZZ
RCRSB0300CEZZ
RCRSB0249GEZZ
PTC B59250-C1080-B70
S
CRYSTAL HC-49/U-S 12000KHz-A1 MS
X'TAL 18.432MHZ (KDS)
S
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
VP-DF270K0000
VP-DF270K0000
VP-CF3R3K0000
VP-DF3R3K0000
VP-DF3R3K0000
VP-DF3R3K0000
VP-DF3R3K0000
VP-XF120K0000
VP-DF3R3K0000
RCILP0225CEZZ
RCILF0111BMZZ
VP-XF100K0000
VP-XF100K0000
VP-XF100K0000
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
VP-CF3R3K0000
VP-CF3R3K0000
VP-CF3R3K0000
PEAK COIL 27UH 10%
PEAK COIL 27UH 10%
PEAK COIL 3.3UH 10%
PEAK COIL 3,3UH 10%
PEAK COIL 3,3UH 10%
PEAK COIL 3,3UH 10%
PEAK COIL 3,3UH 10%
PEAK COIL 12UH 10% 1/8W
PEAK COIL 3,3UH 10%
COIL SL_A TOKYO
COIL HR-19043
PEAK COIL 10UH 10% 1/8W
PEAK COIL 10UH 10% 1/8W
PEAK COIL 10UH 10% 1/8W
PEAK COIL 10UH 10%
PEAK COIL 10UH 10%
PEAK COIL 10UH 10%
PEAK COIL 3.3UH 10%
PEAK COIL 3.3UH 10%
PEAK COIL 3.3UH 10%
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AA
AA
AB
AA
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AA
AE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AC
AA
AA
AA
AC
AA
AB
AB
AB
AB
AB
AA
AB
AA
AD
AF
AE
AA
AA
AB
AB
AB
AB
AB
AA
AB
AA
AE
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AB
AD
AL
AA
AA
AA
AA
AA
AA
AB
AB
AB
PACKAGED CIRCUITS
COILS
DIODES
!
37
0201
0204
0308
0351
0352
0353
0354
0403
0451
0602
0701
0801
0802
1002
3001
3002
3003
3030
3050
3060
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
21HS-50H
REF No. PARTS
DESCRIPTION
* SN CODE EX CODE
CERAMIC FILTERS
CF 0401
SF 0201
RFILC0023CEZZ
RFILC0283BMZZ
SOUND FILTER (TAPED)
SAW FILTER J1980M SIEMENS
S
S
AA
AF
AD
AM
!
T 0601
T 0602
T 0701
RTRNZ0026PEZZ
RTRNF2053CEZZ
RTRNW0005CEZZ
DRIVER TRANSFORMER
FBT BSC21-2643S SHENZHEN
SMT TABUCHI
S
S
S
AA
AM
AA
AF
AY
AP
!
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
VCEA0A1CW476M
VCEA0A1AW107M
VCEA0A1HW106M
VCKYCY1HF223Z
VCKYCY1HB472K
VCKYCY1HB821K
VCKYCY1EF104Z
VCCCCY1HH220J
VCKYPA1HF103Z
VCKYPA1HF103Z
VCCCCY1HH220J
VCEA0A1CW106M
VCEA0A1EW337M
VCEA0A1CW226M
VCKYCY1HF103Z
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCEA0A1CW106M
VCKYCY1HB102K
VCKYCY1HF103Z
VCKYCY1HB102K
VCKYCY1HB102K
VCCSPA1HL221J
VCCSPA1HL221J
VCEA0A1HW225M
VCKYCY1HB332K
VCEA0A1CW106M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HB102K
VCEA0A1CW107M
VCEA0A1CW107M
VCKYCY1HB102K
VCEA0A1CW107M
VCEA0A1CW107M
VCKYCY1HB102K
VCEA0A1CW106M
VCKYCY1HB102K
VCEA0A1CW106M
VCKYCY1HB102K
VCCCCY1HH220J
VCKYCY1HF103Z
VCEA0A1CW106M
VCKYCY1HF223Z
VCKYCY1HB102K
VCKYCY1EF104Z
VCEA0A1CW106M
VCKYCY1HF103Z
VCEA0A1EW477M
VCKYPA1HB102K
VCEA0A1HW107M
VCKYPA1HB102K
VCKYCY1HF103Z
RC-FZ0272CEZZ
VCQYTA2AA563J
VCKYPA1HB102K
VCKYCY1HF103Z
VCKYPA2HB102K
VCEA0A1EW477M
VCQYTA1HM103J
VCKYCY1HB102K
VCKYPA1HB102K
ELEC C 47UF 20% 16V
S
ELEC C 100UF 20% 10V
S
ELEC C 10UF 20% 50V
S
SC CAPACITOR 0.022UF 50V TAPE S
S.CHIP CAP 4700PF/50V T
S
GRM39B 821K 50 (1608)SMD CAPACS
S CHIP TAPE CAP 0.1UF/25V
S
S. CHIP CAP 22PF/50V TAPED
S
C.CAPACITOR 0.01U-F 50V
S
C.CAPACITOR 0.01U-F 50V
S
S. CHIP CAP 22PF/50V TAPED
S
ELEC C 10UF 20% 16V
S
ELEC C 330UF 20% 25V
S
ELEC C 22UF 20% 16V
S
CHIP CAP 0.01UF/50V
S
S. CHIP CAP 0.001UF/50V
S
S. CHIP CAP 0.001UF/50V
S
S. CHIP CAP 0.001UF/50V
S
ELEC C 10UF 20% 16V
S
S. CHIP CAP 0.001UF/50V
S
CHIP CAP 0.01UF/50V
S
S. CHIP CAP 0.001UF/50V
S
S. CHIP CAP 0.001UF/50V
S
CERAM C 220PF 5% 50V
S
CERAM C 220PF 5% 50V
S
ELEC C 2,2UF 20% 50V
S
s.chip cap 3300pf /50v
S
ELEC C 10UF 20% 16V
S
CHIP CAP 0.01UF/50V
S
CHIP CAP 0.01UF/50V
S
S. CHIP CAP 0.001UF/50V
S
ELEC C 100UF 20% 16V
S
ELEC C 100UF 20% 16V
S
S. CHIP CAP 0.001UF/50V
S
ELEC C 100UF 20% 16V
S
ELEC C 100UF 20% 16V
S
S. CHIP CAP 0.001UF/50V
S
ELEC C 10UF 20% 16V
S
S. CHIP CAP 0.001UF/50V
S
ELEC C 10UF 20% 16V
S
S. CHIP CAP 0.001UF/50V
S
S. CHIP CAP 22PF/50V TAPED
S
CHIP CAP 0.01UF/50V
S
ELEC C 10UF 20% 16V
S
SC CAPACITOR 0.022UF 50V TAPE S
S. CHIP CAP 0.001UF/50V
S
S CHIP TAPE CAP 0.1UF/25V
S
ELEC C 10UF 20% 16V
S
CHIP CAP 0.01UF/50V
S
ELEC C 470UF 20% 25V
S
C.CAPACITOR 1000PF/50V
S
ELEC C 100UF 20% 50V
S
C.CAPACITOR 1000PF/50V
S
CHIP CAP 0.01UF/50V
S
C POL P 0,39UF 100V
S
POL FILM C 56NF 5% 100V
S
C.CAPACITOR 1000PF/50V
S
CHIP CAP 0.01UF/50V
S
CERAM C 1NF 10% 500V
S
ELEC C 470UF 20% 25V
S
F. CAPACITOR 0.01UF/50V
S
S. CHIP CAP 0.001UF/50V
S
C.CAPACITOR 1000PF/50V
S
AA
-AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
-AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AC
AB
AA
AA
AA
AB
AA
AA
AA
TRANSFORMERS
!
CAPACITORS
0201
0202
0204
0206
0207
0208
0209
0210
0211
0212
0215
0302
0305
0307
0308
0311
0314
0315
0318
0320
0322
0323
0324
0325
0326
0331
0341
0342
0344
0349
0351
0352
0354
0356
0357
0358
0359
0360
0361
0362
0363
0402
0403
0404
0431
0432
0433
0451
0453
0502
0504
0505
0506
0507
0508
0509
0511
0512
0513
0514
0515
0521
0522
!
!
!
38
REF No. PARTS
DESCRIPTION
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
S. CHIP CAP 0.001UF/50V
S
S. CHIP CAP 0.001UF/50V
S
F. CAPACITOR 0.1 UF 50 V
S
C.CAPACITOR 1000PF/50V
S
ELEC C 470UF 20% 16V
S
ELEC C 100UF 20% 16V
S
C.CAPACITOR 0.01U-F 50V
S
ELEC C 220UF 20% 10V
S
ELEC C 100UF 20% 16V
S
C.CAPACITOR 0.01U-F 50V
S
S CHIP TAPE CAP 0.1UF/25V
S
CERAM C 1NF 10% 500V
S
POL FILM C 82NF 5% 100V
S
PP FILM C 9,1NF 50% 1600V
S
PP FILM C 560NF 5% 200V
S
ELEC C KMF160VB-100MMC NICHICS
F. CAPACITOR 0.1 UF 50 V
S
ELEC C 1UF 20% 50V
S
ELEC C 10UF 20% 50V
S
ELEC C 1UF 20% 160V
S
E CAPACITOR 220UF 16V 6.3x11 S
S CHIP TAPE CAP 0.1UF/25V
S
S CHIP CAPACITOR 0.0022UF/50V TS
ELEC C 100UF 20% 16V
S
POL C B81130 100NF 275V X2
S
CERAM C 10NF 80,20% 250V
S
CERAM C 10NF 80,20% 250V
S
CERAM C 10NF 80,20% 250V
S
ELEC C 100uF 400V LPN100M2GN S
E. CAPACITOR 100UF 25V 6.3x11 S
F. CAPACITOR 0.1 UF 50 V
S
FILM CAPACITOR 474 MAT
S
CERAM C 820PF 2KV
S
C. CAP 2200PF/4KV-KX
S
C.CAPACITOR 1000PF/50V
S
CERAM C 1NF 10% 500V
S
CERAM C DE1105-979BN821K2K-A3S
ELEC C KMF160VB-100MMC NICHICS
C.CAPACITOR 1000PF/50V
S
ELEC C 1000MF 16V 10X16MM
S
E CAPACITOR 220UF 16V 6.3x11 S
E CAPACITOR 220UF/6.3V-5X11 S
CERAM C 1NF 10% 500V
S
ELEC C 1000MF 25V 10X16MM
S
C.CAPACITOR 1000PF/50V
S
S CHIP TAPE CAP 0.1UF/25V
S
CERAM C 68PF 5% 50V
S
ELEC C 100UF 20% 25V
S
ELEC C 100UF 20% 16V
S
CHIP CAP 0.01UF/50V
S
E CAPACITOR 220UF 16V 6.3x11 S
PP FILM C 220NF 5% 50V
S
PP FILM C 220NF 5% 50V
S
S CHIP CAPACITOR 0.0022UF/50V TS
ELEC C 1UF 20% 50V
S
S.CHIP CAP 4700PF/50V T
S
SC CAPACITOR 0.022UF 50V TAPE S
ELEC C 10UF 20% 16V
S
ELEC C 0,47UF 20% 50V
S
S. CHIP CAP 0.001UF/50V
S
S. CHIP CAP 0.001UF/50V
S
S. CHIP CAP 0.001UF/50V
S
S. CAPACITOR 560PF/50V
S
E CAPACITOR 220UF 16V 6.3x11 S
CHIP CAP 0.01UF/50V
S
CHIP CAP 0.01UF/50V
S
E CAPACITOR 220UF 16V 6.3x11 S
CHIP CAP 0.01UF/50V
S
CHIP CAP 0.01UF/50V
S
S. CHIP CAP 22PF/50V TAPED
S
S. CHIP CAP 22PF/50V TAPED
S
SC CAPACITOR 0.022UF 50V TAPE S
ELEC C 100UF 20% 6,3V
S
ELEC C 100UF 20% 6,3V
S
0531
0532
0533
0599
0602
0603
0604
0605
0606
0607
0608
0609
0610
0611
0614
0615
0616
0617
0619
0621
0622
0631
0632
0633
0701
0702
0703
0704
0705
0707
0708
0709
0710
0712
0713
0716
0751
0752
0753
0754
0755
0756
0757
0758
0759
0761
0762
0764
0765
0767
0801
0803
0804
0805
0806
0807
0808
0809
0810
0811
0812
0813
0814
0815
0817
0818
0819
0822
0823
1001
1002
1006
1009
1011
VCKYCY1HB102K
VCKYCY1HB102K
VCQYTA1HM104J
VCKYPA1HB102K
VCEA0A1CW477M
VCEA0A1CW107M
VCKYPA1HF103Z
VCEA0A1AW227M
VCEA0A1CW107M
VCKYPA1HF103Z
VCKYCY1EF104Z
VCKYPA2HB102K
VCFYSB2EB823J
VCFPVC3CA912H
VCFPVC2DB564J
RC-EZ0724CEZZ
VCQYTA1HM104J
VCEA0A1HW105M
VCEA0A1HW106M
VCEA0A2CW105M
VCEA0A1CW227M
VCKYCY1EF104Z
VCKYCY1HB222K
VCEA0A1CW107M
RC-FZ0176BMZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
RC-EZ0150BMZZ
VCEA0A1EW107M
VCQYTA1HM104J
VCFYFA1HA474J
RC-KZ0040CEZZ
RC-KZ0105GEZZ
VCKYPA1HB102K
VCKYPA2HB102K
RC-KZ0299CEZZ
RC-EZ0724CEZZ
VCKYPA1HB102K
VCEA0A1CW108M
VCEA0A1CW227M
VCEA0A0JW227M
VCKYPA2HB102K
VCEA0A1EW108M
VCKYPA1HB102K
VCKYCY1EF104Z
VCCCPA1HH680J
VCEA0A1EW107M
VCEA0A1CW107M
VCKYCY1HF103Z
VCEA0A1CW227M
VCFYFA1HA224J
VCFYFA1HA224J
VCKYCY1HB222K
VCEA0A1HW105M
VCKYCY1HB472K
VCKYCY1HF223Z
VCEA0A1CW106M
VCEA0A1HW474M
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB561K
VCEA0A1CW227M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCEA0A1CW227M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCCCCY1HH220J
VCCCCY1HH220J
VCKYCY1HF223Z
VCEA0A0JW107M
VCEA0A0JW107M
* SN CODE EX CODE
AA
AA
AA
AA
AA
AA
AA
-AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AC
AA
AA
AA
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AA
-AA
AA
AA
AA
AB
AC
AC
AG
AB
AA
AA
AB
AA
AA
AA
AA
AB
AC
AC
AC
AM
AA
AB
AB
AD
AC
AA
AA
AC
AG
AA
AB
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AC
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
21HS-50H
REF No. PARTS
DESCRIPTION
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
1012
1013
1014
1015
1016
1017
1018
3001
3003
3004
3005
3006
3007
3008
3011
3012
3013
3014
3015
3016
3017
3018
3019
3020
3021
3022
3023
3024
3025
3026
3027
3028
3029
3030
VCKYCY1EF104Z
VCKYCY1HF103Z
VCEA0A0JW107M
VCEA0A1CW106M
VCEA0A1CW476M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HB102K
VCKYCY1HB471K
VCEA0A1CW107M
VCEA0A1HW335M
VCEA0A1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEA0A1CW106M
VCCCCY1HH101J
VCCCCY1HH560J
VCCCCY1HH560J
VCCCCY1HH1R5C
VCCCCY1HH1R5C
VCKYCY1EF104Z
VCKYCY1HB102K
VCKYCY1HB471K
VCEA0A1CW106M
VCKYCY1HB102K
VCEA0A1HW105M
VCEA0A1HW105M
VCKYCY1HF103Z
VCEA0A1CW106M
VCKYCY1HB151K
S CHIP TAPE CAP 0.1UF/25V
S
CHIP CAP 0.01UF/50V
S
ELEC C 100UF 20% 6,3V
S
ELEC C 10UF 20% 16V
S
ELEC C 47UF 20% 16V
S
CHIP CAP 0.01UF/50V
S
CHIP CAP 0.01UF/50V
S
CHIP CAP 0.01UF/50V
S
S. CHIP CAP 0.001UF/50V
S
GRM39B 471K 50 (1608)SMD CAPACS
ELEC C 100UF 20% 16V
S
ELEC C 3,3UF 20% 50V
S
ELEC C 10UF 20% 16V
S
S CHIP TAPE CAP 0.1UF/25V
S
S CHIP TAPE CAP 0.1UF/25V
S
S CHIP TAPE CAP 0.1UF/25V
S
S CHIP TAPE CAP 0.1UF/25V
S
S CHIP TAPE CAP 0.1UF/25V
S
ELEC C 10UF 20% 16V
S
S. CHIP CAP 100PF/50V TAPED S
S. CHIP CAP 56PF/50V TAPE
S
S. CHIP CAP 56PF/50V TAPE
S
GRM39CK 1R5C 50 (1608)SMD CAPS
GRM39CK 1R5C 50 (1608)SMD CAPS
S CHIP TAPE CAP 0.1UF/25V
S
S. CHIP CAP 0.001UF/50V
S
GRM39B 471K 50 (1608)SMD CAPACS
ELEC C 10UF 20% 16V
S
S. CHIP CAP 0.001UF/50V
S
ELEC C 1UF 20% 50V
S
ELEC C 1UF 20% 50V
S
CHIP CAP 0.01UF/50V
S
ELEC C 10UF 20% 16V
S
CAPACITOR GRM39B 151K 50 (1608S
* SN CODE EX CODE
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0201
0202
0208
0209
0302
0303
0305
0306
0331
0332
0333
0341
0351
0352
0354
0355
0356
0357
0359
0360
0362
0363
0364
0365
0366
0367
0401
0403
0404
0405
0406
0407
0408
0409
0451
0452
0453
0454
VRD-RA2BE332J
VRS-CY1JF681J
VRS-CY1JF102J
VRS-CY1JF391J
VRS-CY1JF472J
VRD-RA2BE102J
VRD-RA2BE102J
VRS-CY1JF392J
VRS-CY1JF103J
VRS-CY1JF473J
VRD-RA2BE103J
VRS-CY1JF101J
VRS-CY1JF000J
VRS-CY1JF104J
VRS-CY1JF000J
VRS-CY1JF104J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF472J
VRS-CY1JF104J
VRS-CY1JF472J
VRS-CY1JF104J
VRS-CY1JF561J
VRS-CY1JF561J
VRS-CY1JF101J
VRS-CY1JF102J
VRD-RA2BE101J
VRS-CY1JF181J
VRS-CY1JF102J
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE102J
VRD-RA2EE750J
VRS-CY1JF104J
VRS-CY1JF223J
VRS-CY1JF562J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RESISTORS
!
RES 3,3KOHM 5% 1/8W
S
S. CHIP RES. 680-OHM TAPED
S
S.CHIP RES TAPE 1K OHM
S
SURFACE MOUNT CHIP RESISTORS
S. RES. 4.7K OHM TAPED
S
RES 1KOHM 5% 1/8W
S
RES 1KOHM 5% 1/8W
S
S. CHIP RES. 3.9K-OHM TAPED S
S.C. RESISTOR 10K OHM
S
S. CHIP RES 47K-OHM TAPED
S
RES 10KOHM 5% 1/8W
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 100K-OHM TAPED S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 100K-OHM TAPED S
S.CHIP RES TAPE 1K OHM
S
S.C. RESISTOR 10K OHM
S
S.CHIP RES TAPE 1K OHM
S
S.C. RESISTOR 10K OHM
S
S. RES. 4.7K OHM TAPED
S
S. CHIP RES. 100K-OHM TAPED S
S. RES. 4.7K OHM TAPED
S
S. CHIP RES. 100K-OHM TAPED S
S. CHIP RES 560-OHM TAPED
S
S. CHIP RES 560-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S.CHIP RES TAPE 1K OHM
S
RES 100 OHM 5% 1/8W
S
S CHIP RES. 180-OHM TAPED
S
S.CHIP RES TAPE 1K OHM
S
RES 100 OHM 5% 1/8W
S
RES 100 OHM 5% 1/8W
S
RES 1KOHM 5% 1/8W
S
RES 75 OHM 5% 1/4W
S
S. CHIP RES. 100K-OHM TAPED S
S.CHOP REG 22K-OHM T
S
S. CHIP RES. 5.6K-OHM TAPED S
!
!
!
39
REF No. PARTS
DESCRIPTION
* SN CODE EX CODE
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
RES 75 OHM 5% 1/4W
RES 75 OHM 5% 1/4W
RES 75 OHM 5% 1/4W
S.C. RESISTOR 10K OHM
RES 75 OHM 5% 1/4W
RES 75 OHM 5% 1/4W
RES 220KOHM 5% 1/8W
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
RES 3,9KOHM 5% 1/8W
MET FILM R 2,7 OHM 5% 2W
RES 330 OHM 5% 1/2W
S CHIP RES. 180-OHM TAPED
RES 1 OHM 5% 1/8W
S CHIP RES. 180-OHM TAPED
RES 1KOHM 5% 1/8W
RES 1KOHM 5% 1/2W
RES 10 OHM 5% 1/8W
RES 10KOHM 5% 1/8W
S.C. RESISTOR 10K OHM
S CHIP RES. 15K-OHM TAPED
S CHIP RES. 15K-OHM TAPED
S.CHOP REG 22K-OHM T
S. CHIP RES. 330K-OHM TAPED
RES 100 OHM 5% 1/8W
RES 100 OHM 5% 1/8W
RES 39KOHM 5% 1/8W
RES 1KOHM 5% 1/8W
RES 4.7KOHM 5% 1/2W
MET OX RES 3,3KOHM 5% 3W
RES 1KOHM 5% 1/2W
RES 100KOHM 5% 1/8W
MET FILM R 0,82 OHM 5% 1W
RES 100 OHM 5% 1/2W
S.CHIP RES TAPE 1K OHM
S.C. RESISTOR 10K OHM
RES 330 OHM 5% 1/8W
RES 180KOHM 5% 1/2W
RES 4.7KOHM 5% 1/2W
RES 4.7KOHM 5% 1/2W
RES 1,8KOHM 5% 1/2W
RES 12KOHM 5% 1/8W
S. CHIP RES. 0-OHM TAPED
RES 10 OHM 5% 1/2W
RES 82 OHM 5% 1/2W
FUS RES 5,6KOHM 5% 1/2W
RES 12KOHM 5% 1/8W
RES 10KOHM 5% 1/8W
S. CHIP RES. 5.6K-OHM TAPED
S.C. RESISTOR 10K OHM
RES 150 OHM 5% 1/4W
RES 100 OHM 5% 1/8W
RES 390 OHM 5% 1/8W
RES 27KOHM 5% 1/8W
S. CHIP RES. 8.2K-OHM TAPED
S.CHIP RES TAPE 1K OHM
S CHIP RES. 150K-OHM TAPED
S. CHIP RES. 33K-OHM TAPED
S. CHIP RES. 220-OHM TAPED
RES 33KOHM 5% 1/8W
RES 100 OHM 5% 1/8W
WOUND RES 5,6 OHM 10% 5W
RES 1,2KOHM 5% 1/8W
RES 39KOHM 5% 1/8W
RES 1KOHM 5% 1/8W
MET FILM R .27 OHM 5% 1W
RES 27 OHM 5% 1/8W
RES 10 OHM 5% 1/2W
RES 390KOHM 5% 1/8W
SOLID R 8,2MOHM 10% 1/2W
SOLID R 8,2MOHM 10% 1/2W
RES 820KOHM 5% 1/8W
RES 1KOHM 5% 1/2W
MET FILM R 5.6 OHM 5% 2W
MET FILM R 5.6 OHM 5% 2W
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
0455
0456
0457
0458
0459
0460
0461
0490
0491
0501
0502
0503
0504
0505
0507
0509
0511
0512
0513
0514
0515
0516
0517
0518
0531
0532
0533
0603
0604
0605
0606
0607
0608
0609
0610
0611
0612
0613
0614
0615
0616
0618
0619
0620
0621
0623
0624
0625
0626
0627
0629
0630
0631
0632
0633
0634
0636
0637
0638
0639
0640
0701
0706
0707
0708
0710
0711
0712
0713
0715
0716
0718
0752
0753
0758
VRD-RA2EE750J
VRD-RA2EE750J
VRD-RA2EE750J
VRS-CY1JF103J
VRD-RA2EE750J
VRD-RA2EE750J
VRD-RA2BE224J
VRS-CY1JF000J
VRS-CY1JF000J
VRD-RA2BE392J
VRN-VV3DB2R7J
VRD-RA2HD331J
VRS-CY1JF181J
VRD-RA2BE1R0J
VRS-CY1JF181J
VRD-RA2BE102J
VRD-RA2HD102J
VRD-RA2BE100J
VRD-RA2BE103J
VRS-CY1JF103J
VRS-CY1JF153J
VRS-CY1JF153J
VRS-CY1JF223J
VRS-CY1JF334J
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE393J
VRD-RA2BE102J
VRD-RA2HD472J
VRS-KT3LB332J
VRD-RA2HD102J
VRD-RA2BE104J
VRN-RV3ABR82J
VRD-RA2HD101J
VRS-CY1JF102J
VRS-CY1JF103J
VRD-RA2BE331J
VRD-RA2HD184J
VRD-RA2HD472J
VRD-RA2HD472J
VRD-RA2HD182J
VRD-RA2BE123J
VRS-CY1JF000J
VRD-RA2HD100J
VRD-RA2HD820J
VRG-RL2HB562J
VRD-RA2BE123J
VRD-RA2BE103J
VRS-CY1JF562J
VRS-CY1JF103J
VRD-RA2EE151J
VRD-RA2BE101J
VRD-RA2BE391J
VRD-RA2BE273J
VRS-CY1JF822J
VRS-CY1JF102J
VRS-CY1JF154J
VRS-CY1JF333J
VRS-CY1JF221J
VRD-RA2BE333J
VRD-RA2BE101J
VRW-KP3HC5R6K
VRD-RA2BE122J
VRD-RA2BE393J
VRD-RA2BE102J
VRN-VV3ABR27J
VRD-RA2BE270J
VRD-RA2HD100J
VRD-RA2BE394J
VRC-UA2HG825K
VRC-UA2HG825K
VRD-RA2BE824J
VRD-RA2HD102J
VRN-VV3DB5R6J
VRN-VV3DB5R6J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
21HS-50H
!
REF No. PARTS
DESCRIPTION
R 0761
R 0762
R 0763
R 0766
R 0768
R 0770
R 0771
R 0772
R 0773
R 0774
R 0801
R 0802
R 0803
R 0804
R 0805
R 0806
R 0807
R 0808
R 0809
R 1001
R 1002
R 1003
R 1004
R 1005
R 1006
R 1008
R 1009
R 1014
R 1015
R 1016
R 1017
R 1018
R 1019
R 1020
R 1022
R 1023
R 1024
R 1025
R 1026
R 1027
R 1028
R 1029
R 1033
R 1034
R 1035
R 1036
R 1037
R 1038
R 1040
R 1041
R 1042
R 1043
R 1044
R 1047
R 1048
R 1052
R 1053
R 1054
R 1056
R 1057
R 1058
R 3001
R 3002
R 3003
R 3004
R 3007
R 3008
R 3009
R 3010
R 3011
R 3012
RJ 0001
RJ 0002
RJ 0004
RES 1,5KOHM 5% 1/8W
S
RES 180KOHM 5% 1/2W
S
RES 8,2KOHM 5% 1/8W
S
RES 18KOHM 5% 1/4W
S
RES 120KOHM 5% 1/2W
S
RES 180 OHM 5% 1/2W
S
RES 180 OHM 5% 1/2W
S
S. CHIP RES. 33K-OHM TAPED
S
S CHIP RES. 15K-OHM TAPED
S
S. CHIP RES. 3.3K-OHM TAPED S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S.CHOP REG 22K-OHM T
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S CHIP RES. 180-OHM TAPED
S
S. CHIP RES. 220-OHM TAPED
S
S CHIP RES TAPE 330 OHM
S
S. CHIP RES. 680-OHM TAPED
S
S. RES. 4.7K OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 0-OHM TAPED
S
RES 100 OHM 5% 1/8W
S
RES 100 OHM 5% 1/8W
S
RES 3,3KOHM 5% 1/8W
S
RES 100 OHM 5% 1/8W
S
RES 3,3KOHM 5% 1/8W
S
S. CHIP RES. 100-OHM TAPED
S
S CHIP RES. 15K-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
RES 15KOHM 5% 1/8W
S
S. CHIP RES. 100-OHM TAPED
S
S. RESISTOR 1.2K OHM
S
S. CHIP RES. 220K-OHM TAPED S
S. CHIP RES. 100-OHM TAPED
S
RES 100 OHM 5% 1/8W
S
S. CHIP RES. 100-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
RES 3,3KOHM 5% 1/8W
S
S. CHIP RES. 100-OHM TAPED
S
RES 3,3KOHM 5% 1/8W
S
RES 100 OHM 5% 1/8W
S
S.CHOP REG 22K-OHM T
S
S. CHIP RES. 1.5K-OHM
S
S. CHIP RES. 1.5K-OHM
S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 5.6K-OHM TAPED S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 0-OHM TAPED
S
SURFACE MOUNT CHIP RESISTORS
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
S.C. RESISTOR 10K OHM
S
S. RES. 4.7K OHM TAPED
S
S. CHIP RES. 100-OHM TAPED
S
RES 100 OHM 5% 1/8W
S
RES 100 OHM 5% 1/8W
S
RES 100 OHM 5% 1/8W
S
RES 100 OHM 5% 1/8W
S
S.CHIP RES TAPE 1K OHM
S
S.C. RESISTOR 10K OHM
S
S. CHIP RES. 33K-OHM TAPED
S
S.C. RESISTOR 10K OHM
S
S. CHIP RES. 33K-OHM TAPED
S
S.C. RESISTOR 10K OHM
S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 0-OHM TAPED
S
S. CHIP RES. 0-OHM TAPED
S
VRD-RA2BE152J
VRD-RA2HD184J
VRD-RA2BE822J
VRD-RA2EE183J
VRD-RA2HD124J
VRD-RA2HD181J
VRD-RA2HD181J
VRS-CY1JF333J
VRS-CY1JF153J
VRS-CY1JF332J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF223J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF181J
VRS-CY1JF221J
VRS-CY1JF331J
VRS-CY1JF681J
VRS-CY1JF472J
VRS-CY1JF101J
VRS-CY1JF000J
VRS-CY1JF000J
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE332J
VRD-RA2BE101J
VRD-RA2BE332J
VRS-CY1JF101J
VRS-CY1JF153J
VRS-CY1JF101J
VRD-RA2BE153J
VRS-CY1JF101J
VRS-CY1JF122J
VRS-CY1JF224J
VRS-CY1JF101J
VRD-RA2BE101J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-RA2BE332J
VRS-CY1JF101J
VRD-RA2BE332J
VRD-RA2BE101J
VRS-CY1JF223J
VRS-CY1JF152J
VRS-CY1JF152J
VRS-CY1JF000J
VRS-CY1JF562J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF391J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF101J
VRS-CY1JF103J
VRS-CY1JF472J
VRS-CY1JF101J
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE101J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF333J
VRS-CY1JF103J
VRS-CY1JF333J
VRS-CY1JF103J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
* SN CODE EX CODE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
REF No. PARTS
DESCRIPTION
* SN CODE EX CODE
RJ 0008
RJ 0009
RJ 0010
RJ 0011
RJ 0012
RJ 0019
RJ 0020
RJ 0024
RJ 0025
RJ 0026
RJ 0027
RJ 0029
RJ 0031
RJ 0033
RJ 0035
RJ 0036
RJ 0044
RJ 0046
RJ 0047
RJ 0048
RJ 0055
RJ 0056
RJ 0057
RJ 0058
RJ 0059
RJ 0061
RJ 0062
RJ 0064
RJ 0065
RJ 0067
RJ 0068
RJ 0070
RJ 0072
RJ 0075
RJ 0077
RJ 0078
RJ 0080
RJ 0081
RJ 0082
RJ 0085
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S. CHIP RES. 0-OHM TAPED
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
F 0701
F 0751
FB 0451
FB 0452
FB 0601
FB 0701
FH 0701
FH 0702
P 0302
P 0601
P 0602
P 0701
P 0702
P 0801
P 1001
RMC1001
S 0701
S 1001
S 1002
S 1003
S 1004
S 1005
SC 0451
VA 0701
QFS-C3229CEZZ
QFS-J2521CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
QFSHD1001BMZZ
QFSHD1002BMZZ
QPLGN0441CEZZ
QPLGN0441CEZZ
QPLGN0505CEZZ
QPLGN0304CEZZ
QPLGN0207CEZZ
QPLGN0541CEZZ
QPLGN0641CEZZ
RRMCU0255CEZZ
QSW-P0591CEZZ
QSW-K0079GEZZ
QSW-K0079GEZZ
QSW-K0079GEZZ
QSW-K0079GEZZ
QSW-K0079GEZZ
QSOCZ2107BMZZ
RH-VX0047CEZZ
FUSE S506-3.15A-A1 TOKYO COMPS
FUSE 2,5A 125V LITTELFUSE (KURS
BALUN FBA04HA90088-00 T/Y
S
BALUN FBA04HA90088-00 T/Y
S
BALUN FBA04HA90088-00 T/Y
S
BALUN FBA04HA90088-00 T/Y
S
FUSE HOLD.EYF52BC=PANASON S
FUSE HOLD.EYF52BC=PANASON S
PLUG 4PIN
S
PLUG 4PIN
S
PLUG
S
PLUG
S
PLUG
S
PLUG
S
PLUG
S
R/C RECEIVER TSOP1838UH1 ELEKS
SWITCH SDDFC3-A ALPS
S
TACTILE SWITCH
S
TACTILE SWITCH
S
TACTILE SWITCH
S
TACTILE SWITCH
S
TACTILE SWITCH
S
SOCKET
S
VARISTOR SIOV-S14K420M4 MATS S
AA
AC
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AD
AA
AA
AA
AA
AA
AF
AA
AC
AD
AB
AB
AB
AB
AA
AA
AA
AA
AB
AB
AA
AA
AA
AG
AL
AA
AA
AA
AA
AA
AE
AC
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
MISCELLANEOUS PARTS
!
!
!
PWB-B
SOCKET UNIT
TRANSISTORS
!
40
Q
Q
Q
Q
Q
Q
0870
0871
0872
0883
0885
0887
VSBF422////-1
VSBF422////-1
VSBF422////-1
VSBF421////-1
VSBF421////-1
VSBF421////-1
TRT BF422 PHILIPS
TRT BF422 PHILIPS
TRT BF422 PHILIPS
TRT BF421 PHILIPS
TRT BF421 PHILIPS
TRT BF421 PHILIPS
S
S
S
S
S
S
21HS-50H
REF No. PARTS
DESCRIPTION
* SN CODE EX CODE
D
D
D
D
D
0811
0812
0880
0881
0882
RH-DX0045BMZZ
RH-DX0045BMZZ
VHD1SS82///1A
VHD1SS82///1A
VHD1SS82///1A
DIODE 1N4148
DIODE 1N4148
DIODE 1SS82-A HITACHI
DIODE 1SS82-A HITACHI
DIODE 1SS82-A HITACHI
S
S
S
S
S
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
C
C
C
C
C
C
C
C
C
0871
0872
0873
0875
0876
0878
0880
0881
0882
VCKYPA1HB471K
VCKYPA1HB471K
VCKYPA1HB471K
VCKYPA2HB102K
RC-KZ0150CEZZ
VCEAGA2EW336M
VCKYPA1HB471K
VCKYPA1HB471K
VCKYPA1HB471K
CERAM C 470PF 10% 50V
S
CERAM C 470PF 10% 50V
S
CERAM C 470PF 10% 50V
S
CERAM C 1NF 10% 500V
S
CERAM C DE0707-726E102Z3K-A MS
ELEC C 33UF 20% 250V
S
CERAM C 470PF 10% 50V
S
CERAM C 470PF 10% 50V
S
CERAM C 470PF 10% 50V
S
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AD
AA
AA
AA
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0879
0880
0881
0882
0883
0884
0885
0886
0887
0892
0893
0894
0895
0896
0899
VRD-RA2BE471J
VRD-RA2BE471J
VRD-RA2BE471J
VRS-VV3DB153J
VRD-RA2HD272J
VRS-VV3DB153J
VRD-RA2HD272J
VRS-VV3DB153J
VRD-RA2HD272J
VRD-RA2BE102J
VRD-RA2BE102J
VRD-RA2BE102J
VRD-RA2BE471J
VRD-RA2BE471J
VRD-RA2BE471J
RES 470 OHM 5% 1/8W
RES 470 OHM 5% 1/8W
RES 470 OHM 5% 1/8W
MET OX RES 15KOHM 5% 2W
RES 2,7KOHM 5% 1/2W
MET OX RES 15KOHM 5% 2W
RES 2,7KOHM 5% 1/2W
MET OX RES 15KOHM 5% 2W
RES 2,7KOHM 5% 1/2W
RES 1KOHM 5% 1/8W
RES 1KOHM 5% 1/8W
RES 1KOHM 5% 1/8W
RES 470 OHM 5% 1/8W
RES 470 OHM 5% 1/8W
RES 470 OHM 5% 1/8W
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
P 0851
P 0882
P 0883
SC 0882
QPLGN0441CEZZ
QPLGN0541CEZZ
QTIPM0017CEFM
QSOCV0931CEZZ
PLUG 4PIN
S
PLUG
S
TIP
S
CRT SOCKET HPS0521-013404-A H S
AA
AA
AA
AB
AA
AA
AA
AF
QACCB5008BMZZ
VSP9050PB33WA
VSP9050PB33WA
QCNW-6072CEZZ
RRMCGA006WJSA
UBATU0247AJZZ
QSOCN0302CEZZ
QTIPM0025TAZZ
QCNW-5969CEZZ
QCNW-5970CEZZ
TINS-7133BMN0
TINS-7190BMN0
AC CORD
S
SPEAKER 509SF32C001MA MISAW S
SPEAKER 509SF32C001MA MISAW S
WIRE (S)
S
R/C HOSHIDEN
S
BATTERY R6(X2)
S
SOCKET SMK W-A5303-1N
S
PIN SMK W-T0512-11
S
WIRE (H)
S
WIRE (K)
S
OWNERS MANUAL 21HS50H
S
QUICK START GUIDE 21HS50H
S
AF
AA
AA
AA
AA
AE
AA
AA
AA
AA
AA
AA
AQ
AK
AK
AG
AV
AH
AB
AA
AC
AD
AK
AC
CCABA1367BMV0
HBDGB3508BMSB
HDECQ0069BMSA
JBTN-1082BMSB
JBTN-1081BMSA
GCABB1129BMKB
CABINET SET 21HS50H
SHARP BADGE
DECORATION POWER
BUTTON
POWER BUTTON
REAR CABINET
AA
AC
AA
-AA
AA
BH
AG
AC
-AC
BA
DIODES
CAPACITORS
1
1.1
RESISTORS
1.4
MISCELLANEOUS PARTS
!
SP 0301
SP 0302
CABINET PARTS
!
1
1.1
1.2
1.3
1.4
2
S
S
S
S
S
S
1.3
2
MISCELLANEOUS PARTS
!
1.2
41
21HS-50H
DOCUMENTATION OF SOURCES.
1.
TDA9350, Philips Data Sheet:
TDA935X/6X/8X PS/N2 series, TV signal processor-Teletext decoder with embedded µ-Controller. Tentative Device
Specification, 2001 Aug 29, Version: 2.9.
2.
TEA1507, Philips Data Sheet:
TEA1507 GreenChipII SMPS controlIC. Preliminary specification, 2000Dec05.
3.
AN7523, Matsushita Electronics Corporation Specifications:
AN7523 Product Specifications. Doc No. SDSC-PSE-AN7503, Eff. Date 23-FEB-01.
4.
AN5522, Matsushita Electronics Corporation Specifications:
AN5522 Product Specifications. Doc No. SDSC-PSE-AN5522, Eff. Date 21-NOV-2000.
5.
MSP34x5G, Micronas Preliminary Data sheet.
MSP34x5g Multistandard Sound Processor Family. Edition March 5,2001
6251-480-3PD
42
21HS-50H
NOTES:
43
21HS-50H
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP ELECTRONICA ESPAÑA S.A.
TV Division
Engineering Dept.
Polígono Industrial Can Sant Joan
Sant Cugat del Vallès
Barcelona
Spain
PRINTED BY:
ON:
Think Ecology, please use
RECYCLED PAPER
44