Miele H 4786 BP Operating and Specifications

Installation Instructions
H4784 BP, H4786 BP
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
Caring for the environment
Disposal of the packing
materials
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
68
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet and
cut off its power cord. Remove any
doors to prevent trapping hazards.
Electrical connection
,CAUTION: Before servicing,
Data plate
disconnect the power supply by
either removing the fuse, shutting off
the power main or manually
"tripping" the circuit breaker.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous.
Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the data plate correspond with the
household electrical supply. This
data must correspond to prevent
machine damage. Consult an
electrician if in doubt.
The silver data plate is located along
the front side of the oven (door open).
Power supply
The oven comes equipped with a
7.2 ft. (2.2 m) power cord with a
NEMA 14-30 P molded plug ready
for connection to a:
120/240 V, 20 A, 60 Hz power supply.
or
Only operate the appliance after it
has been installed into cabinetry.
The plug must be plugged into an
appropriate outlet that is installed
and grounded in accordance with all
local codes and ordinances.
120/208 V, 20 A, 60 Hz power supply.
WARNING: THIS APPLIANCE
MUST BE GROUNDED
Installer:
Please leave these instructions with
the consumer.
69
Appliance and Cut-out Dimensions
Miele appliances can be installed flush or proud. Discuss your installation
requirements with your architect, designer and installer.
70
Appliance and Cut-out Dimensions
a Vent cut-out (min. 24" 2 / 150 cm2) possible at rear of cabinet
b Cut-out for power cord (min. 4"2 / 10 cm2)
c Power cord
For the most current specifications see the Miele web site.
71
Installing the oven
The oven must be installed into
cabinetry before use.
o not insulate the cabinet. This will
prevent proper ventilation.
,IMPORTANT INFORMATION
Certain cabinet materials and
finishes are very sensitive to high
temperatures. To eliminate the risk
of damage to surrounding cabinets,
a 24 square inch (2"x12") [150 cm2]
minimum opening must exist in the
cabinet to allow air to flow into and
around the appliance. In addition,
the oven vent at the bottom of the
door must not be obstructed.
^ Connect the oven to the electrical
supply.
The oven must be supported from
underneath.
^ Place the oven into the cabinet as far
as the oven trim and align.
^ Open the oven door and locate the
two mounting screw holes in the oven
frame. Mark and drill 6 mm pilot
holes. Secure the oven to the
cabinetry by inserting screws through
the frame and into the cabinetry.
Only operate the appliance after it
has been installed into the cabinetry.
72
Installing the oven
Set the time
"Enter Time: hh:mm" will appear in the
display once the oven is connected to
electricity.
^ Set the current time using the
keypad.
^ Save the time by touching the "OK"
control.
73
74
75
Alteration rights reserved / 2311
(H 4784 BP, H 4786 BP)
M.-Nr. 07 964 140 / 00
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.