Emerson LD200EM8 Owner`s manual

INTRODUCTION
TM
EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.
Owner's Manual
INITIAL SETTING
LD200EM8
CONNECTION
20" Digital / Analog LCD TV
built-in DVD Player
WATCHING TV
OPTIONAL SETTING
OPERATING DVD
DVD SETTING
TROUBLESHOOTING
IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-256-2487, OR
VISIT OUR WEB SITE AT http://www.EmersonAudioVideo.com
INFORMATION
TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA.
INTRODUCTION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE
ACCOMPANYING THE APPLIANCE.
The important note is located on the rear of the cabinet.
Important Safeguards
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the
operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions
should be followed.
5. CLEANING - Unplug TV from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
EXCEPTION: A product that is meant for uninterrupted service and,
that for some specific reason, such as the possibility of the loss
of an authorization code for a CATV converter, is not intended to
be unplugged by the user for cleaning or any other purpose, may
exclude the reference to unplugging the appliance in the cleaning
description otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by
the TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this TV near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on
an unstable cart, stand, tripod, bracket,
or table. The TV may fall, causing serious
injury to someone, and serious damage to
the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the TV.
Any mounting of the appliance should follow
the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
AMEUBLES - Cet appareil ne doit être placé
que sur un meuble (avec ou sans roulettes)
recommandé par le fabricant. Si vous l’
installez sur un meuble à roulettes, déplacez
les deux ensembles avec précaution. Un arrêt
brusque, l’utilisation d’une force excessive
et des surfaces irrégulières risquent de
déstabiliser l’ensemble et de le renverser.
9. VENTILATION - Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the TV and to protect it from overheating, these
openings must not be blocked or covered. The openings should
never be blocked by placing the TV on a bed, sofa, rug, or other
similar surface. This TV should never be placed near or over a
radiator or heat register. This TV should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES - This TV should be operated only from the type
of power source indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your appliance
dealer or local power company. For TVs intended to operate from
battery power, or other sources, refer to the operating instructions.
2
EN
11. GROUNDING OR POLARIZATION - This TV is equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they
exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or
cable system is connected to the TV, be sure the antenna or cable
system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA No. 70, provides information
with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SEC TION 810-20)
ELEC TRIC
SERVICE
EQUIPMENT
GROUNDING CONDUC TORS
(NEC SEC TION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELEC TRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELEC TRODE SYSTEM
(NEC ART 250, PART H)
14. LIGHTNING - For added protection for this TV receiver during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the TV due
to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light of
power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment
may cause harmful interference unless the modifications are expressly approved in the manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to
possible eye injury.
TROUBLESHOOTING
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the
building as close to the point of cable entry as practical.
DVD SETTING
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
OPERATING DVD
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
OPTIONAL SETTING
CAUTION:
WATCHING TV
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.
INITIAL SETTING
5 Precautions
CONNECTION
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance, this
indicates a need for service.
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts specified by
the manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
TV, ask the service technician to perform routine safety checks to
determine that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
INTRODUCTION
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this TV through openings as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the TV.
c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the TV to its normal operation.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates
copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
INFORMATION
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
3
EN
INTRODUCTION
LOCATION
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the
unit. Do not place the unit on a carpet because this will block the ventilation holes.
• Install the unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving the unit to locations where temperature differences are extreme.
• Be sure to unplug the AC power cord from the outlet before carrying the unit.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug the power cord immediately and take the unit to our authorized service center for
servicing.
• Do not place anything directly on top of the unit.
MOISTURE WARNING
• Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold
room or under conditions of high humidity.
When the condensation occurs inside the unit, turn the unit on and leave it at least 2 hours to dry out.
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You
should record the number and other vital information here and retain this book as a permanent record of your purchase to aid
identification in case of theft.
date of purchase
dealer phone No.
serial No.
dealer purchase from
model No.
dealer address
Note about recycling:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
5 Supplied Accessories
owner’s manual
(1EMN22105)
remote control
(NF602UD)
batteries
(AA x 2)
• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free
customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
Contact your local electronics store for these items.
5 Tilt Stand
5 Symbols Used in this Manual
You can adjust the stand to change the angle
of the TV (-2.5° to 10°).
-2.5°
10°
The following is the description for the symbols used
in this manual.
Description refers to:
TV FUNCTIONS
TV
DTV
: Analog TV
operation
: Digital TV
operation
• If neither symbol appears
under the function
heading, operation is
applicable to both.
4
EN
DVD FUNCTIONS
DVD
CD
: Playback of
DVD-video
: Playback of
audio CD
• If neither symbol appears
under the function
heading, operation is
applicable to both.
INTRODUCTION
5 Contents
INTRODUCTION
DVD Functions
Basic Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INITIAL SETTING
WATCHING TV
OPTIONAL SETTING
TROUBLESHOOTING
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
INFORMATION
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Electrical Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back cover
DVD SETTING
Channel Add/Delete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DTV Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DTVCC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Back Light Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Color Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DVD Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Display Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
DVD Audio Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Parental Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Reset to the Default Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
OPERATING DVD
Channel Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Volume Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Switching Each Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TV Screen Display Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DVD SETTING
OPTIONAL SETTING
Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WATCHING TV
TV Functions
Playable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Unplayable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
DVD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Resume Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Step-by-step Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fast Forward / Fast Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Slow Forward / Slow Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Search Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Repeat A-B Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Programmed Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Random Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
On-screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Special Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
INITIAL SETTING
CONNECTION
OPERATING DVD
CONNECTION
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tilt Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TROUBLESHOOTING
INFORMATION
5
EN
INTRODUCTION
5 Features
TV
• DTV/TV/CATV
- You can use your remote control to select channels
which are broadcast in digital, conventional analog,
standard definition. Also, cable subscribers can
access their cable TV channels.
• Program Information Display (DTV only)
- You can display the title, contents and other
information of the current DTV program on the TV
screen.
• Auto Channel Scan
- This unit automatically scans and memorizes
channels available in your area, eliminating difficult
setup procedures.
• V-chip
- This feature allows you to block children’s access to
inappropriate TV programs.
• Closed Caption Decoder
- Built-in closed caption decoder displays text for
closed caption supported programming.
• MTS/SAP Tuner
- Audio language or stereo sound function can be
selected from the remote control.
• Auto Shut Off Function
- If there is no signal input from the antenna terminal
and no operation for 15 minutes, the unit will turn
itself off automatically.
• Sleep Timer
- This feature will automatically turned off the power
of the unit at a specific time.
• Choices for On-screen Language
- Select your on-screen language:
English, Spanish or French.
• PLL Frequency Synthesized Tuning
- Provides free and easy channel selection and lets
you tune directly to any channel using the channel
number buttons on the remote control.
• Component Video Input
• S-video Input
• AV Input
• Digital Audio Coaxial Output
DVD
• Dolby Digital Sound
- Enjoy Dolby Digital multi-channel surround sound
when you connect the unit to your Dolby Digital
decoder.
• Still / Fast / Slow / Step Playback
- Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
• DVD Menus in a Desired Language
- You can display DVD menus in a desired language, if
available on a DVD-video.
• Screen Saver
- If there is no operation for 5 minutes, the screen
saver program starts.
• Parental Lock
- Block the viewing of DVD-video unsuitable for
children.
• Resume Play
- Lets you resume play back from the point at which
playback was stopped.
• Bit Rate Indication
• Dynamic range control (DRC)
- You can control the range of sound volume.
• Choices for Audio Language and Stereo Sound
Function
- Select your desired language or stereo sound
function when different options are available on
your disc.
¨ Accessing from [MODE] button
During playback
• Subtitles in a Desired Language
- You can select a desired language for displaying
subtitle, if that language is available on a DVD-video.
• Selecting a Camera Angle
- You can select the desired camera angle, if a DVD
contains sequences recorded from different angles.
• Zoom
- Allows you to enlarge the size of picture image.
• Black Level Adjustment
• Virtual Surround
• Search
- chapter search / title search / track search / time
search
• Marker
- The part designated by user can be called back.
• Repeat
- chapter / title / track / all / A-B
In stop mode
• Program Playback for audio CD
- You can program the order of tracks to play them
back in designated order.
• Random Playback for audio CD
- This unit can shuffle the order of tracks to play them
back in randomly.
6
EN
INTRODUCTION
5 Remote Control Function
12
13
14
15
1
2
3
16
17
18
5
19
20
6
21
8
3.
4.
10
11
24
25
TROUBLESHOOTING
5 Installing the Batteries
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
2
3
INFORMATION
1
DVD SETTING
POWER button (p13)
Press to turn the unit on and off.
MUTE button (p16)
Press to turn the sound on and off.
SLEEP button (p19)
Press to activate the sleep timer.
Number buttons (p16)
• Press to select channels.
• Press to select chapter, title (DVD), or track
(CD) directly.
-/ENT button
• Press to shift the minor channel from the
major channel.
+10/+100 button
• Press to select 100 or higher channels. (CATV)
• Press to search if there are minor channels on
the currently selected major channel. (DTV)
OPERATING DVD
2.
22
23
OPTIONAL SETTING
1.
9
WATCHING TV
7
INITIAL SETTING
4
12. EJECT A button (p28)
Press to eject the disc.
13. INPUT button (p17)
Press to access a connected external device
like a video game, camcorder or VCR.
14. DISPLAY button (p18 / p33)
Digital Mode (DTV)
• Press to display the channel number
and the program information.
Analog Mode (TV)
• Press to display the channel No.
External Input Mode
• Press to display the currently selected
external input mode.
15. AUDIO button (p17 / p34)
Digital Mode (DTV)
• Press to select the audio language.
Analog Mode (TV)
• Press to select the audio mode.
DVD Mode
• Press to select the audio language
(DVD), or sound mode (CD).
16. SCREEN MODE button (p19)
Press to select aspect ratio available for
the TV screen.
17. PICTURE button (p20)
Press to adjust the picture quality.
18. CH. RETURN button (p16)
Press to return to previous channel.
19. CH. K/L buttons (p16)
Press to select channels.
20. PLAY B button (p28)
Press to begin disc playback.
21. STOP C button (p28)
Press to stop disc playback.
22. s / B / K / L buttons (p13)
Press to move left/ right/ up/ down
through the items.
23. ENTER button (p13)
Press to confirm your selection.
24. MENU button (p28)
Press to call up the menu on a disc.
25. TOP MENU button
Press to call up the top menu on a disc.
(DVD-Video)
CONNECTION
VOL. X/Y buttons (p16)
Press to adjust the volume.
6. PAUSE button (p28)
Press to pause disc playback.
7. SKIP H / G button (p30)
• Press to skip forward or backward
chapters, titles (DVD) or tracks (CD).
REV E button (p29)
• Press and hold to begin slow reverse
playback during the pause mode (DVD)
and search backward through a disc.
FWD D button (p29)
• Press and hold to begin slow forward
playback during the pause mode (DVD)
and search forward through a disc.
8. SETUP button (p14 / p37)
Press to display the main menu.
9. RETURN button (p20)
Press to return to the previous menu
operation.
10. CLEAR button (p31)
• Press to clear the numbers entered
incorrectly.
• Press to cancel the point A for A-B
repeat (DVD, CD).
• Press to remove the track number in
program input (CD).
11. MODE button (p6)
• Press to arrange the playing order or
playback randomly (CD).
• Press to set the black level (DVD) and
the virtual surround (DVD, CD) on or off.
• Press to change the camera angle to
see the sequence being played back
from different angle (DVD-video).
• Press to search chapter, title (DVD),
time (DVD, CD) or track (CD).
• Press to set the marker (DVD, CD).
• Press to repeat playback chapter, title
(DVD), track, disc (CD) repeatedly or
between designated point A and B
(DVD, CD).
• Press to magnify the part of picture
(approx. 1.3x, 2x and 4x : DVD).
• Press to select the subtitles on a disc
(DVD).
5.
Battery Precautions:
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can overheat and rupture.
7
EN
INTRODUCTION
5 Control Panel
1
2
3
4
5
6
7
8
SETUP
STOP
PLAY
EJECT
VOLUME
CHANNEL
INPUT
POWER
DVD
top of the unit
9
10
1.
SETUP button (p14 / p37)
Press to display the main menu.
7.
INPUT button (p17)
Press to select the digital, analog or external input.
2.
STOP C button (p28)
Press to stop disc playback.
8.
POWER button (p13)
Press to turn the unit on and off.
3.
PLAY B button (p28)
Press to begin disc playback.
9.
4.
EJECT A button (p28)
Press to eject the disc.
Infrared Sensor Window
Receives infrared rays transmitted from the remote
control.
5.
VOLUME X / Y buttons (p16)
Press to adjust the volume.
6.
CHANNEL K/L buttons (p16)
Press to select channels or move up/down through
the main menu items.
8
EN
10. Disc Loading Slot (p28)
Insert the disc with label facing back of this unit.
INTRODUCTION
5 Rear Panel
CONNECTION
INITIAL SETTING
ANT
HEADPHONE
Y
Pb
COMPONENT
Pr
L
R
AUDIO
VIDEO 2
COAXIAL
S-VIDEO
VIDEO
L
R
AUDIO
VIDEO 1
WATCHING TV
side of the unit
1
OPTIONAL SETTING
rear of the unit
2
3
Pb
L
Pr
COMPONENT
VIDEO 2
COAXIAL
S-VIDEO
R
AUDIO
L
VIDEO
VIDEO 1
OPERATING DVD
Y
4
R
AUDIO
5
6
2.
HEADPHONE jack
Headphone connection for personal listening.
3.
COMPONENT and AUDIO input jacks (p11)
Component video cable connection for an external
device.
Use component video and audio output jacks of an
external device.
4.
AUDIO input jacks (p11)
RCA audio cable connection for an external device.
5.
VIDEO input jack (p12)
RCA video cable connection for an external device.
6.
S-VIDEO input jack (p11)
S-video cable connection for an external device.
7.
COAXIAL (digital audio) output jack (p12)
Digital audio coaxial cable connection for a decoder or
an audio receiver.
Use digital audio input jack of an external device.
8.
AC power cord
Connect to a standard AC outlet to supply power to
this unit.
INFORMATION
ANT jack (p10)
RF coaxial cable connection for your antenna or cable
box.
TROUBLESHOOTING
1.
DVD SETTING
7
8
9
EN
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
5 Basic Connection
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
[Antenna Cable Connection]
When connecting the unit to an antenna or cable TV company (without cable/satellite box)
Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
e.g.)
VHF / UHF
antenna
rear of this unit
RF coaxial cable
or
ANT
HEADPHONE
Y
Pb
COMPONENT
L
Pr
R
AUDIO
VIDEO 2
cable TV
company
COAXIAL
S-VIDEO
VIDEO
R
L
AUDIO
VIDEO 1
*Once connections are completed, turn on the unit and begin initial setup.
Channel scanning is necessary for the unit to memorize all available channels in your area.
(Refer to “Initial Setup” on page 13.)
Note:
• For your safety and to avoid damage to device, please unplug the RF coaxial cable from the antenna input jack before moving the unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than settop versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CATV installer.
[Connection to Cable Box or Satellite Box]
Connect the RF coaxial cable on your home outlet to the input jack of the cable/satellite box.
Use another RF coaxial cable to connect the antenna input jack of the unit to the output jack of the cable/satellite box.
e.g.)
rear of this unit
satellite
dish
or
cable/satellite box
ANT. IN RF OUT
ANT
HEADPHONE
Y
Pb
COMPONENT
Pr
L
R
AUDIO
VIDEO 2
COAXIAL
S-VIDEO
VIDEO
R
L
AUDIO
VIDEO 1
cable TV
company
RF coaxial cable
RF coaxial cable
*Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
10
EN
INTRODUCTION
Cables not included.
Please purchase the necessary cables at your local store.
CONNECTION
5 External Device Connection
INITIAL SETTING
[Component Video Cable Connection]
Component video connection offers better picture quality for video devices connected to the unit.
Use a component video cable to connect the unit to external video devices equipped with component video output
jacks.
If you connect to the unit’s component video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO2.
component
video cable
(green)
(blue)
(red)
e.g.)
WATCHING TV
rear of this unit
Y
Pb
Pr
COMPONENT VIDEO OUT
DVD player with the component
video output jacks
AUDIO OUT
L
R
Y
Pb
Pr
(green)COMPONENT
(blue) (red)
L
R
AUDIO
COAXIAL
S-VIDEO
VIDEO
L
OPTIONAL SETTING
VIDEO 2
R
AUDIO
VIDEO 1
RCA audio cable
OPERATING DVD
Note:
• This unit accepts 480i / 480p / simplified 1080i video signals.
• Simplified 1080i video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal.
e.g.)
AUDIO OUT
L
R
S-VIDEO
OUT
DVD SETTING
[S-video Cable Connection]
S-video connection offers good picture quality for video devices connected to the unit.
Use an S-video cable to connect the unit to external video devices equipped with S-video output jack.
If you connect to the unit’s S-video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1.
rear of this unit
TROUBLESHOOTING
DVD player with the S-video
output jack
Y
Pb
Pr
L
COMPONENT
VIDEO 2
COAXIAL
S-VIDEO
VIDEO
VIDEO 1
R
AUDIO
L
R
AUDIO
S-video cable
INFORMATION
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
11
EN
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
[Video Connection]
Video connection offers standard picture quality for video devices connected to the unit.
If you connect to the unit’s video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1.
When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack.
e.g.)
rear of this unit
AUDIO OUT
L
R
camcorder
VIDEO
OUT
video game
Y
Pb
L
Pr
COMPONENT
VIDEO 2
COAXIAL
S-VIDEO
RCA video cable
VCR
R
AUDIO
VIDEO
L
VIDEO 1
R
AUDIO
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
[Digital Audio Output Connection]
If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound.
e.g.)
rear of this unit
DIGITAL AUDIO
COAXIAL IN
Y
Pb
Pr
L
COAXIAL
S-VIDEO
VIDEO
VIDEO 1
Dolby Digital decoder
12
EN
digital audio coaxial cable
R
AUDIO
COMPONENT
VIDEO 2
L
R
AUDIO
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
5 Initial Setup
Note:
Before you begin:
Make sure if the unit is connected to antenna or cable.
[POWER] to turn on the unit.
• This operation may take a few moments.
from the choices on the right side of the TV screen.
(ENGLISH / ESPAÑOL / FRANÇAIS)
SELECT : K,, L
SELECCIONE : K,, L
CHOIX : K,, L
ENGLISH
ESPAÑOL
FRANÇAIS
OPTIONAL SETTING
SELECT LANGUAGE
SELECCIONE EL IDIOMA
CHOISIR LA LANGUE
- HELPFUL HINTS 1. PLEASE CHECK TO SEE IF THE
ANTENNA / CABLE / SATELLITE IS
PROPERLY CONNECTED.
2. DID YOU PERFORM “AUTO PRESET CH”?
3. PLEASE REFER TO FRONT PAGE OF THE
OWNER’S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.
WATCHING TV
2 Use [Cursor K /L] to select the on-screen language
INITIAL SETTING
1 After making all the necessary connections, press
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during “AUTO PRESET CH”,
this setting will be canceled.
• The initial auto channel scan function can be executed for
either TV/DTV or CATV only once. If you want to scan both
TV/DTV and CATV, you need to select “CHANNEL SETUP” in
the main menu to scan and memorize other channels after
initial presetting is completed. (Refer to page 14.)
• You can cancel or exit the initial “AUTO PRESET CH” menu by
pressing [SETUP].
• When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
“HELPFUL HINTS” appears. Follow the instructions listed on
the TV screen.
CONNECTION
This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and “AUTO PRESET CH”, which
automatically scans and memorizes viewable channels.
or
INTRODUCTION
INITIAL SETTING
SET : ENTER
AJUSTE : ENTER
VALIDER : ENTER
OPERATING DVD
• “INITIAL SETUP“ menu on step 3 will be displayed in
the selected language after you press [ENTER].
3 Use [Cursor K /L] to select “AUTO PRESET CH(TV/DTV)”
for TV channels or “AUTO PRESET CH(CATV)“ for CATV
channels, then press [ENTER].
DVD SETTING
or
- INITIAL SETUP PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
TROUBLESHOOTING
• Scanning and memorizing the channels automatically
start.
25
INFORMATION
AUTO PRESET CH(TV/DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel in the broadcasting
will be displayed.
13
EN
INITIAL SETTING
5 Main Menu
5 Auto Channel Scan
This section describes the overview of the main menu displayed when you
press [SETUP]. For more details, see the reference page for each item.
The main menu consists of the function setting items below.
If you switch wires (e.g., between antenna and CATV) or if you move the
unit to a different area after the initial setting, or if you restore the DTV
channel you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
Press [SETUP] to display the main menu.
e.g.) digital TV mode
1 Press [SETUP] to display the main menu.
- TV SETUP CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
2
• CHANNEL SETUP
You can automatically scan the viewable channels and
remove those that are undesired.
(Refer to “Auto Channel Scan” on page 14.)
Use [Cursor K/L] to select “CHANNEL SETUP”, then
press [ENTER].
e.g.) digital TV mode
- TV SETUP -
or
• V-CHIP SETUP
You can set the viewing limitations.
(Refer to “V-chip” on page 24.)
• LANGUAGE
You can change the language (English, Spanish,
French) displayed on the main menu.
(Refer to “Language Selection” on page 15.)
• CAPTION
You can change the display format for closed caption,
which displays the dialogue of a TV program or other
information across the TV screen.
(Refer to “Closed Caption” on page 21.)
• BACK LIGHT
You can set the desired brightness mode. (Refer to
“Back Light Setting” on page 23.)
• COLOR TEMP
You can adjust color temperature (“NORMAL”, “WARM”
and “COOL”). (Refer to “Color Temperature” on page 24.)
• DTVCC
In addition to the basic closed caption described on
page 21, DTV has its own closed caption called DTVCC.
(Refer to “DTV Closed Caption” on page 22.)
3
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
Use [Cursor K/L] to select your desired preset type,
then press [ENTER].
e.g.) digital TV mode
--- CHANNEL SETUP ---
or
ADD/DELETE (DTV)
AUTO PRESET CH (DTV)
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
! CATV takes approx. 50min.
• When aerial antenna is connected, select “AUTO
PRESET CH(TV)”, “AUTO PRESET CH(DTV)” or “AUTO
PRESET CH(TV/DTV)”.
• When connected to CATV, select “AUTO PRESET CH
(CATV)”.
• Scanning and memorizing the channels automatically
start.
e.g.) digital TV mode
D25
AUTO PRESET CH(DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
• When you selected “AUTO PRESET CH(TV/DTV)”, the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed.
If there is no analog channel, the lowest memorized
digital channel will be displayed.
14
EN
5 Language Selection
You can choose English, Spanish, or French as your on-screen language.
1 Press [SETUP] to display the main menu.
CONNECTION
INITIAL SETTING
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel scan,
the setting will be canceled.
• When no channel can be received by auto channel scan,
“NO TV SIGNALS” will be displayed on the TV screen.
• Channel settings will be saved even if the power fails.
• If you have Spanish or French menus and need English,
press [SETUP]. Use [Cursor K/L] to select “IDIOMA”
or “LANGAGE”. Press [ENTER] to select “ENGLISH”. Press
[SETUP] to remove the main menu.
• With regard only to the digital channel, even after the
scanning is complete if you unplug the AC power cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.
INTRODUCTION
Note:
2 Use [Cursor K /L] to select “LANGUAGE”, then press
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
- TV SETUP -
or
WATCHING TV
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
OPTIONAL SETTING
[ENGLISH]
[ESPAÑOL]
[FRANÇAIS]
OPERATING DVD
3 Press [SETUP] to exit.
DVD SETTING
TROUBLESHOOTING
INFORMATION
15
EN
WATCHING TV
5 Channel Selection
5 Volume Adjustment
Select channels by pressing [CH. K/L] or [the Number buttons].
This section describes how to adjust the volume. The mute function, which
turns the sound off and on, is also described.
• To select the memorized channels,
use [CH. K/L] or [the Number buttons].
• To select the non-memorized channels use
[the Number buttons].
Use [VOL. X/Y] to adjust the audio volume.
or
To Use [the Number buttons]
TV
VOLUME
20
- When selecting analog channel 12
DTV
- When selecting digital channel 12-1
Be sure to press [–/ENT.] before entering the minor
channel number.
• Press [CH. RETURN] to return to the previously
viewed channel.
• When you select a channel larger than 100, press
[+100] first. Then use [the Number buttons] to press
the lower 2-digit numbers.
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting
far surpasses analog broadcasting in both its picture
and sound quality.
What is the minor channel?
By using high compression technology, digital
broadcasting offers a service that enables multiple
signals to send simultaneously.
Therefore, you can select more than one program per
major channel since digital broadcasting technology
distinguishes between multiple channels broadcast by
a single network.
NTSC (analog mode) [Air Time]
18:00
ATSC (digital mode)
CH4
No signal
No signal
18:30
CH4
(high definition TV)
CH4
19:00
CH4
CH4-1
No signal
CH4
No signal
CH4-2
CH4
CH4-1
CH4-2
19:30
20:00
20:30
major channel
minor channel
: change automatically
: change manually by using [CH. K/L]
Although, you cannot watch the high definition TV
(HDTV) program, the unit converts the HDTV signal
down to the standard definition TV signal.
Note:
• “NO SIGNAL” will appear on the TV screen after the minor
channel broadcast is over.
16
EN
• The volume bar will be displayed at the bottom of the
TV screen when adjusting the volume.
• The volume bar display will automatically disappear in
a few seconds.
Press [MUTE] to turn off and on the sound.
MUTE
20
• “MUTE” is displayed on the TV screen for a few
seconds.
Press [MUTE] again or [VOL. X/Y] to recover the
original volume.
INTRODUCTION
5 Switching Each Mode
5 Switching Audio Mode
You can easily switch with the remote control to the DTV (ATSC) and TV
(NTSC) or to access an external device when they are connected to the unit.
This section describes how to switch the audio in the analog mode and how
to switch the audio language in the digital mode.
CONNECTION
TV
1 Press [INPUT] repeatedly to cycle through analog TV,
digital TV, VIDEO1 and VIDEO2.
While receiving an MTS broadcast, press [AUDIO]
repeatedly to cycle through the available audio
channel.
[ANALOG MODE]
INITIAL SETTING
[MAIN]
[DIGITAL MODE]
[SAP]
[VIDEO1]
[MONO]
• To use the video or S-video input jack on the unit,
select “VIDEO1”.
• To use the component video input jack on the unit,
select “VIDEO2”.
MAIN
: Outputs main-audio
SAP
: Outputs second audio program
MONO
: Outputs mono-audio
• The current mode will automatically disappear in 10
seconds.
WATCHING TV
[VIDEO2]
• When you switch the analog mode to the digital mode,
it may take a while until the digital channel selection is
completed. The following TV screen is displayed while
switching the mode.
OPTIONAL SETTING
DTV
Note:
1 Press [AUDIO] to display the currently selected
language and the number of available languages.
KABC
A Day of Memories
ENGLISH 1/3
CH 95-03
OPERATING DVD
NOW SCANNING
2 Press [AUDIO] repeatedly to cycle through the
DVD SETTING
available audio languages.
[ENGLISH]
[SPANISH]
TROUBLESHOOTING
[FRENCH]
• Available languages differ depending on the
broadcast.
• The current mode will automatically disappear in 10
seconds.
INFORMATION
Note:
• Pressing [AUDIO] does not control external audio device.
17
EN
WATCHING TV
5 Screen Information
You can display the currently selected channel or other information such as
the audio mode on the TV screen.
DTV
TV
In the analog mode, the current channel number is displayed.
Press [DISPLAY].
In the digital mode, the detailed broadcasting information for the current
channel such as program title, program guides are displayed.
Press [DISPLAY] repeatedly to cycle through the
available display modes.
CH 10
[OFF]
[BROADCASTING INFORMATION]
• The current channel number is displayed at the topright corner of the TV screen.
• To clear the display, press [DISPLAY] again.
[PROGRAM GUIDE]
[Broadcasting Information]
• The following information is displayed.
1 channel number
2 broadcast station
3 program title
4 audio language
(“OTHER” is displayed when the audio language cannot
be acquired, or the acquired languages are other than
English, Spanish or French.)
2
3
4
KABC
A Day of Memories
ENGLISH 1/3
CH 95-03
1
[Program Guide]
• The program guide added to broadcasting
information is displayed.
program
guide
KABC
CH 95-03
A Day of Memories
ENGLISH 1/3
A quarter-century ago, which may now
qualify as the good old days of newspapering, run-of-paper sales accounted
for 80 percent of the industry’s advertising revenues.
Next - Push L Key
Back - Push K Key
Note:
• When the program guide consists of more than 6 lines, use
[Cursor K/ L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• While the program guide is displayed, the closed caption
function is interrupted.
• In external input mode, the following screen is displayed;
e.g.) When an external device is connected to VIDEO1 input
jack.
VIDEO 1
• Available languages differ depending on the broadcast.
• The information display will automatically disappear in 1
minute.
• Pressing [AUDIO] does not control external audio device.
18
EN
DTV
Press [SCREEN MODE] repeatedly to switch the TV
aspect ratio.
5 Sleep Timer
The sleep timer can be set to automatically turn off the unit after an
incremental period of time.
CONNECTION
2 types of display modes can be selected in the digital mode when the
broadcasting station is sending 16:9 video signal.
INTRODUCTION
5 TV Screen Display Mode
1 Press [SLEEP] to set the sleep timer.
INITIAL SETTING
SLEEP OFF
• Sleep timer display appears on the TV screen.
WATCHING TV
2 Press [SLEEP] repeatedly to change the amount of
time until shut off.
LETTERBOX
ZOOM
The right and left side of image will be cut off.
Note:
• You can set your unit to turn off after a set period of
time (from 30 to 120 minutes).
• Each press of [SLEEP] will increase the time by 30
minutes.
• After set up, the sleep timer display can be called up
for checking by pressing [SLEEP].
To Cancel the Sleep Timer
Press [SLEEP] repeatedly until “SLEEP OFF“ is displayed
on the TV screen.
OPERATING DVD
• You may not switch the display mode depending on the
program.
SLEEP 120MIN.
OPTIONAL SETTING
[LETTERBOX]
Display the digital-supported program in full-screen.
Black borders will spread in the upper and lower
screen.
[ZOOM]
Enlarge and display the center area of the digitalsupported program.
DVD SETTING
Note:
• The sleep timer setting display will automatically disappear
in 10 seconds.
• When you disconnect the unit from the AC outlet or when a
power failure occurs, the sleep timer setting will be canceled.
TROUBLESHOOTING
INFORMATION
19
EN
OPTIONAL SETTING
5 Channel Add/Delete
Note:
The channel add/delete function lets you add the channel that was not
added by the auto channel scan due to the reception status at the initial
setting. You can also delete the unnecessary channels.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K/L] to select “CHANNEL SETUP”, then
• ”ADD/DELETE(DTV)” or “ADD/DELETE(TV)” menu will
disappear automatically in about 10 seconds.
• In the digital mode (DTV), you can add or delete channels
only for major channel.
• Once you delete a DTV channel, you cannot recover the
channel without performing auto channel scan again.
(Refer to “Auto Channel Scan” on page 14.)
5 Picture Adjustment
You can adjust brightness, contrast, color, tint and sharpness.
press [ENTER].
e.g.) digital TV mode
- TV SETUP -
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
1 Press [PICTURE] to adjust the picture quality.
2 Use [Cursor K /L] to select the picture quality type you
want to adjust.
3
[BRIGHTNESS]
Use [Cursor K/L] to select “ADD/DELETE(DTV)” or
“ADD/DELETE”, then press [ENTER].
[CONTRAST]
or
e.g.) digital TV mode
[COLOR]
--- CHANNEL SETUP ---
or
ADD/DELETE (DTV)
AUTO PRESET CH (DTV)
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
! CATV takes approx. 50min.
[TINT]
[SHARPNESS]
3 Within 5 seconds, use [Cursor s / B] to adjust the
4
Select the channel you want to add or delete. (Refer to
“Channel Selection“ on page 16.)
e.g.) digital TV mode
quality.
or
D25
ADD/DELETE : DTV
5 Use [Cursor s/ B] to select “ADD” or “DELETE”.
or
• To add or delete another channels, repeat steps 4-5.
• Color of channel number displayed at the right top of
the TV screen indicates;
- Blue: The selected channel will be added.
- Red: The selected channel will be deleted.
6 Press [SETUP] to exit.
20
EN
Cursor
3
Cursor
4
BRIGHTNESS
to decrease brightness
CONTRAST
to decrease contract
to increase contract
COLOR
to decrease color
to brighten color
TINT
to add purple
to add green
SHARPNESS
to make soft
to make clear
to increase brightness
4 Press [RETURN] to exit.
Note:
• The picture adjustment setting display will automatically
disappear in 10 seconds.
INTRODUCTION
5 Closed Caption
TV
3 Press [SETUP] to exit.
2 Use [Cursor K /L] to select “CAPTION”, then press
Note:
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
or
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
[CAPTION1]
[TEXT1]
OPERATING DVD
[CAPTION2]
OPTIONAL SETTING
[OFF]
• To show the closed caption on your TV screen, broadcast
signal must contain the closed caption data.
• Not all TV programs and commercials have the closed
caption or all types of the closed caption.
• Captions and texts may not match the TV voice exactly.
• Changing channels may delay the closed caption for a few
seconds.
• Adjusting or muting the volume may delay the closed
caption for a few seconds.
• Abbreviations, symbols and other grammatical shortcuts
may be used in order to keep pace with the on-screen
action. This is not a problem with the unit.
• The caption or text characters will not be displayed while
the main menu or functions display is shown.
• If a black box appears on the TV screen, this means that the
closed caption is set to TEXT mode. To clear the box, select
“CAPTION 1”, “CAPTION 2” or “OFF”.
• If the unit receives poor quality television signals, the
captions may contain errors, or there might be no captions
at all. Some possible causes of poor quality signals are:
- Automobile ignition noise
- Electric motor noise
- Weak signal reception
- Multiplex signal reception (ghosts or screen flutter)
• The unit retains the closed caption setting if the power fails.
WATCHING TV
- TV SETUP CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
INITIAL SETTING
1 Press [SETUP] to display the main menu.
CONNECTION
You can view closed captioning (cc) for TV programs, movies and news.
Closed caption refer to text of dialogue or descriptions displayed on-screen
for the hearing impaired.
[TEXT2]
DVD SETTING
TROUBLESHOOTING
[Caption Mode]
CAPTION1 and TEXT1;
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
(up to 4 lines of script on the TV screen, where it does
not obstruct relevant parts of the picture).
CAPTION2 and TEXT2;
are rarely available and broadcasters use them
only in special conditions, such as when “CAPTION1”
or “TEXT1” is not available.
• There are 3 display modes according to programs:
Paint-on mode: Displays input characters on the TV
screen immediately.
Pop-on mode: Once characters are stored in
memory, they are displayed all at
once.
Roll-up mode: Displays the characters continuously
by scrolling (max. 4 lines).
INFORMATION
21
EN
OPTIONAL SETTING
5 DTVCC Style
5 DTV Closed Caption
DTV
DTV
In addition to the basic closed caption described on page 21, DTV has its
own closed caption called DTVCC. Use this menu to change the settings for
DTVCC.
You can change the style of DTV CC such as font, color or size, etc.
1 Press [SETUP] to display the main menu.
1
2 Use [Cursor K /L] to select “DTVCC“, then press
2 Use [Cursor K /L] to select “DTVCC“, then press
[ENTER].
Press [SETUP] to display the main menu.
[ENTER].
e.g.) digital TV mode
e.g.) digital TV mode
- TV SETUP -
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
- TV SETUP -
or
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
3 Use [Cursor K /L] to select “CAPTION SERVICE“, then
press [ENTER] repeatedly to change the setting.
- DTVCC CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
or
[SERVICE1/6]
[ON]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
OFF
Select if you do not want
DTVCC. This is the default.
SERVICE1~6
Select one of these before
changing any other item in
“CAPTION” menu. Choose
“SERVICE1/6” under normal
circumstances.
CAPTION SERVICE
4 Press [SETUP] to exit.
Note:
• “CAPTION SERVICE” you can switch differs depending on the
broadcast description.
22
EN
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
3 Use [Cursor K /L] to select “USER SETTING“, then press
[ENTER] repeatedly to set to “ON”.
• Items in the dotted box are available only when “USER
SETTING“ is “ON“.
or
- DTVCC CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
[SERVICE1/6]
[ON]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
4 Use [Cursor K /L] to select an item, then press
[ENTER] repeatedly to change the setting for the item.
or
- DTVCC CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
[SERVICE1/6]
[ON]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
INTRODUCTION
5 Back Light Setting
You can set the desired brightness mode.
CONNECTION
1 Press [SETUP] to display the main menu.
• CAPTION SIZE
Closed captioning font size can be changed as below.
• CHARACTER EDGE
Edge type of the displayed caption can be switched
as below.
2 Use [Cursor K /L] to select “BACK LIGHT”, then press
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
- TV SETUP -
or
• FORE OPACITY, BACK OPACITY
Text and background opacity of the displayed caption
can be switched as below.
[NORMAL]
STYLE3/8
Proportionally spaced with
serifs.
STYLE4/8
Monospaced with serifs.
STYLE5/8
Proportionally spaced
without serifs.
STYLE6/8
Casual font type.
STYLE7/8
Cursive font type.
STYLE8/8
Small capitals.
3 Press [SETUP] to exit.
DVD SETTING
Monospaced with serifs.
[DARK]
OPERATING DVD
STYLE2/8
OPTIONAL SETTING
FONT STYLE
Proportional font used in the
menu screen.
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
[BRIGHT]
MIDDLE, LARGE, SMALL
STYLE1/8
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
WATCHING TV
• FORE COLOR, BACK COLOR
Font and background color of the displayed caption
can be switched as below.
CAPTION SIZE
INITIAL SETTING
• FONT STYLE
Font style of the displayed caption can be switched as
below.
NONE, RAISED, DEPRESSED, UNIFORM,
CHARACTER EDGE
SHADOW LEFT, SHADOW RIGHT
SOLID, TRANSLUCENT, FLASH
FORE COLOR
WHITE, BLACK, RED, GREEN, YELLOW,
BLUE, MAGENTA, CYAN, TRANSPARENT
BACK OPACITY
SOLID, TRANSLUCENT, FLASH
BACK COLOR
BLACK, RED, GREEN, BLUE, YELLOW,
MAGENTA, CYAN, TRANSPARENT, WHITE
TROUBLESHOOTING
FORE OPACITY
5 Press [SETUP] to exit.
INFORMATION
23
EN
OPTIONAL SETTING
5 Color Temperature
5 V-chip
You can adjust color temperature of the TV screen.
V-chip reads the ratings for programs, then denies access to the programs
which exceed the rating level you set. With this function, you can block
certain programming inappropriate for children.
1 Press [SETUP] to display the main menu.
1 Press [SETUP] to display the main menu.
2 Use [Cursor K /L] to select “COLOR TEMP.”, then press
2 Use [Cursor K /L] to select “V-CHIP SETUP“, then press
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
[ENTER].
e.g.) digital TV mode
- TV SETUP -
- TV SETUP -
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
[NORMAL]
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
3 Use [the Number buttons] to enter the 4-digit
numbers for your password.
[WARM]
PASSWORD
[COOL]
- - - -
3 Press [SETUP] to exit.
• When you have not set up your password, enter 0000.
• When the password is correct, the following “V-CHIP
SETUP” menu is displayed.
See the following description for setting each item.
e.g.) digital TV mode
A... “A. TV Rating”
D page 25
B... “B. MPAA Rating”D page 26.
C... “C. Change Password”
D page 26
- V - CHIP SETUP TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
A
B
C
Note:
• “DOWNLOADABLE RATING“ will be available when the unit
receivers a digital broadcast using the new rating system.
• When you select a rating and set it to “BLOCK”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set the highest rating to “VIEW”, all ratings turn
to “VIEW” automatically.
• If the “PROTECTED PROGRAM” message appears during
your TV viewing, change to a channel that is not blocked.
Then, you can access “V-CHIP SETUP” menu and change the
setting to allow all TV viewing.
• To block any inappropriate programming, set your limits in
both “TV RATING” and “MPAA RATING”.
• The V-chip setting will be retained after a power failure
(except the access code reverts to 0000).
24
EN
INTRODUCTION
A. TV Rating
[ENTER].
e.g.) digital TV mode
--- V--CHIP SETUP --TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
[To Set the Sub Ratings]
As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further
set the sub ratings to block specific elements of
programming. To set the sub ratings, follow the steps
below.
1 Use [Cursor K /L ] to select the desired main rating,
then press [ENTER] twice to show its sub ratings.
or
5 Use [Cursor K /L ] to select the desired rating, then
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
WATCHING TV
TV-Y
TV-Y7 (DLSV)
TV-G
TV-PG (DLSV)
TV-14 (DLSV)
TV-MA (DLSV)
press [ENTER] repeatedly to switch between “VIEW”
and “BLOCK”.
2 Use [Cursor K /L ], then press [ENTER] repeatedly
[VIEW]
) [VIEW]
[VIEW]
) [VIEW]
) [VIEW]
) [VIEW]
to change the setting.
e.g.) TV-PG
or
[BLOCK]
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
OPERATING DVD
Rating
TV-PG
OPTIONAL SETTING
TV-Y
TV-Y7 (
TV-G
TV-PG (
TV-14 (
TV-MA (
or
INITIAL SETTING
or
CONNECTION
4 Use [Cursor K /L] to select “TV RATING”, then press
Category
TV-Y
Appropriate for all children
TV-Y7
Appropriate for all children 7 and
older
lower
Sub Rating
TV-G
General audience
FV
Fantasy Violence
TV-Y7
TV-PG
Parental guidance suggested
V
Violence
TV-14
Unsuitable for children under 14
S
Sexual Situation
TV-MA
Mature audience only
L
Coarse Language
TV-PG
TV-14
TV-MA
D
Suggestive Dialogue
TV-PG, TV-14
Rating
DVD SETTING
higher
Category
TROUBLESHOOTING
6 Press [SETUP] to exit.
Note:
INFORMATION
• Blocked sub ratings will appear beside the main rating
category in “TV RATING” menu.
• You cannot block a sub rating (D, L, S or V) if the main rating
is set to “VIEW”.
• Changing the category to “BLOCK” or “VIEW” automatically
changes all its sub ratings to the same (“BLOCK” or “VIEW”).
25
EN
OPTIONAL SETTING
B. MPAA Rating
C. Change Password
MPAA Rating is the rating system created by MPAA (Motion Picture
Association of America).
Although the default code “0000” is supplied with the unit, you can set
your own password.
4 Use [Cursor K /L] to select “MPAA RATING”, then press
4 Use [Cursor K /L] to select “CHANGE PASSWORD”, then
[ENTER].
press [ENTER].
--- V--CHIP SETUP ---
or
--- V--CHIP SETUP ---
or
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
5 Use [Cursor K /L], then press [ENTER] repeatedly to
change the setting.
or
G
PG
PG-13
R
NC-17
X
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
5 Press [the Number buttons] on the remote control to
enter the new 4-digit password.
• Enter password again in “CONFIRM PASSWORD.”
space.
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
NEW PASSWORD
_ _ _ _
CONFIRM PASSWORD
_ _ _ _
Rating
Category
G
General audience
PG
Parental guidance suggested
PG-13
Unsuitable for children under 13
R
Restricted; under 17 requires accompanying
parent or adult guardian
NC-17
No one under 17 admitted
X
Mature audience only
6 Press [SETUP] to exit.
26
EN
6 Press [SETUP] to exit.
Note:
• Make sure new password and confirm password must be
exactly the same. If they are different, the space is cleared
for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs or when you turn off
the power using a wall switch. If you forget the password,
unplug the power cord for 10 seconds to restore the
password to 0000.
INTRODUCTION
OPERATING DVD
DVD Functions
Type of media
Mark (logo)
DVD-video
*1, 2, 4, 6, 10, 11
Region code
1
Recorded
signals
Media size
PREPARATION
CONNECTION
5 Playable Media
Disc types
or ALL
DVD+RW
DVD+R
* 1, 4, 5, 6, 9, 10
-
audio CD
* 4, 6, 10
-
e. g.)
digital video
(MPEG2)
title 1
title 2
chapter 1 chapter 2 chapter 3 chapter 4 chapter 1 chapter 2
WATCHING TV
-
INITIAL SETTING
DVD-RW
DVD-R
* 1, 3, 4, 5,
6, 7, 8, 9, 10
5 inches
(12 cm)
OPTIONAL SETTING
e. g.)
digital audio
CD-RW
CD-R
* 4, 5, 6, 9,10
track 1
track 2
track 3
track 4
track 5
track 6
-
If you cannot play back a disc which bears one of the marks above, check the following notes.
TROUBLESHOOTING
This unit conforms to the NTSC color system. Discs recorded in other color system such as PAL cannot be played back.
Certain DVD-video does not operate as described in this manual due to the intentions of the disc’s producers.
Discs recorded in VR (video recording) format cannot be played back.
Scratched or stained discs may not be played back.
Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or special properties of discs.
You can play back discs which bear the marks above. If you use non-standardized discs, this unit may not play them back. Even if they are
played back, the sound or video quality will be compromised.
*7: You may play back the unfinalized DVD-RW/-R recorded in the video format on our brand’s DVD recorder. However, depending on the
recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth, etc.). In this case,
you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back. Unfinalized discs cannot be played back. Depending on the
recording status of a disc, the disc may not be played back at all or the picture or sound may not be smooth, etc.
*9: If the recorded portion of the disc is too small (less than 2 3/16 inches (55 mm) across), it may not play back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.
*11: The number inside the symbol refer to region of the world and disc encoded in a specific region format can only be played back on unit
with the same region cord.
DVD SETTING
*1:
*2:
*3:
*4:
*5:
*6:
OPERATING DVD
is a trademark of DVD Format/Logo Licensing Corporation.
INFORMATION
5 Unplayable Media
• NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM, DVD-audio, CD-i, photo CD, video CD, DVD with region codes other than 1 or ALL, DTS-CD,
DVD-ROM for personal computers, CD-ROM for personal computers, CD-RW/-R with MP3 files.
• On the following disc, the sound MAY NOT be heard.
super audio CD
Note:
• Only the sound recorded on the normal CD layer can be delivered. The sound recorded on the high density super audio CD layer
cannot be delivered.
• Any other discs without compatibility indications
27
EN
OPERATING DVD
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
5 Playback
Before you begin:
Turn on the amplifier and any other equipment which is connected to this
unit. Make sure the external audio receiver are set to the correct input
mode.
1 Press [POWER] to turn on the unit.
Note:
• “ ” may appear at the top-right on the TV
screen when the operation is prohibited by
the disc or this unit.
• Some DVD may start playback from title 2 or 3 due to specific
programs.
• During the playback of a 2-layered disc, pictures may stop for
a moment. This happens while the 1st layer is being switched
to the 2nd layer. This is not a malfunction.
5 DVD Menu
DVD
2 Insert a disc with label facing back from the left side of
the unit.
Some discs contain disc menus which describe the contents of the disc or
allow you to customize disc playback, or title menu which lists the titles
available on the DVD.
Press [MENU] to call up the disc menu.
Use [Cursor K / L / s / B] to select an item, then press
[ENTER] (or [PLAY B]).
Note:
• In case the DVD was recorded on both sides, make
sure the label of the side you want to play back is
facing back.
• The unit switches to the DVD mode when the unit
was in TV mode.
3 Press [PLAY B]. Playback will start.
• If playback does not start automatically,
press [PLAY B] again.
4
Press [STOP C] to stop playback temporarily.
• If playback remains stopped for 5 minutes, the screen
saver program will activate automatically, when
“SCREEN SAVER“ is set to “ON“.
5 Press [EJECT] to eject the disc.
• Menu operations may vary depending on the disc.
Refer to the manual accompanying the disc for more details.
5 Resume Playback
Press [STOP C] during playback.
Resume message will appear on
the TV screen.
Press [PLAY B]. Playback will
resume from the point at which
playback was stopped.
Resume ON
Press 'PLAY' to play from here.
To play the beginning,
press 'STOP' first and then 'PLAY'.
Note:
• To cancel resume, press [STOP C] one more time in the stop
mode. On some discs, [STOP C] will not work while the resume
message appears. Please wait until the message disappears.
• The resume information will be kept even when unit is turned
off. However, ejecting the disc will cancel the resume feature.
Playback will start at the beginning the next time you insert
the disc.
5 Pause
Press [PAUSE F] during playback.
• Playback will be paused and sound will be
muted.
To continue playback, press [PLAY B].
28
EN
INTRODUCTION
5 Zoom
5 Step-by-step Playback
DVD
DVD
CONNECTION
The zoom function allows you to enlarge the video image and to pan
through the enlarged image.
Each time you [PAUSE F] in the pause
mode, the disc goes forward one frame at a
time.
1 During playback, press [MODE] repeatedly until
“
To continue playback, press [PLAY B].
” appears.
OFF (ZOOM)
INITIAL SETTING
Note:
• Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in
the pause mode are blurred. (Refer to page 38.)
5 Fast Forward / Fast Reverse
“OFF (ZOOM)“, “1.3x (ZOOM)”, “2x (ZOOM)“ or “4x (ZOOM)“.
E1
4 ×(ZOOM)
WATCHING TV
Press and hold [REV /h] or [FWD /g]
during playback to select the required
forward or reverse speed.
2 Press [ENTER] repeatedly to change the zoom factor;
To continue playback, press [PLAY B].
3 Once a desired zoom factor is set, press [RETURN] to
display the position guide, then use [Cursor K/ L/ s / B]
to slide the zoomed picture across the TV screen.
OPERATING DVD
• Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in
the fast playback mode are blurred. (Refer to page 38.)
• Fast forward / fast reverse speed varies with disc.
Approximate speed is 1(2x), 2(8x), 3(20x), 4(50x) and 5(100x)
on DVD and 1(2x), 2(8x) and 3(30x) on audio CD.
• For DVD, sound will be muted during the search.
• For audio CD, sound will be intermittent during the search.
OPTIONAL SETTING
Note:
5 Slow Forward / Slow Reverse
DVD
DVD SETTING
Press and hold [REV /h] or [FWD /g]
during the paused mode to select the
required forward or reverse speed.
1
To continue playback, press [PLAY B].
4 To exit zoom, repeat steps 1 to 2 above and press
[ENTER] until “OFF (ZOOM)“ appears.
TROUBLESHOOTING
Note:
Note:
• The gray box with an inner blue box that shows during
zoomed playback is the position guide indicates the position
of the zoomed image within the overall image.
Position guide stays on the TV screen until you press [ENTER].
Press [ENTER] one more time to recall the position guide
when disappears.
• Zoom function does not work while the disc menu is
displayed.
• 4x zoom is not available on some discs.
• Zoom function is also available during pause mode.
INFORMATION
• Slow forward / slow reverse speed varies with disc.
Approximate speed is 1(1/16x), 2(1/8x) and 3(1/2x).
• Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in
the slow playback mode are blurred. (Refer to page 38.)
• The sound will be muted during slow forward/slow reverse
playback.
29
EN
OPERATING DVD
5 Search Functions
Chapter / Title Search
DVD
Track Search
CD
Using [MODE]
Using [MODE]
playback, press [MODE] repeatedly until
1 During
“
“ appears.
1 During playback, press [MODE] repeatedly until
“
“ appears.
• If you want to perform the title search, press
[Cursor K / L] repeatedly until “ “ appears.
_ _ /29 (SEARCH)
_ _ /12 (SEARCH)
2 Press [the Number buttons] to select your desired
2
Press [the Number buttons] to select your desired
chapter or title within 60 seconds.
track within 60 seconds.
_ _ /29 (SEARCH)
_ _ /12 (SEARCH)
To play back a single-digit chapter or title when there
are more than 10 chapters or titles, press [ENTER] after
entering the chapter or title number.
will start automatically from the chapter or
3 Playback
title you selected.
Note:
• The total number of chapters/titles in your disc; with less than
10 chapters/titles, press the chapter/title number directly.
With 10 or more chapters/titles, to play a single digit chapter/
title, press [0] first, then the chapter/title number. (e.g., for
chapter 3, press [0] and [3].) To play a double-digit chapter/
title, press the chapter/title number.
Using [SKIP H / G]
1 During playback, press [SKIP H / G] repeatedly
until a desired chapter or title will be selected.
or
current chapter
(CH)
CH 1 CH 2 CH 3 CH 4
[SKIP H]
[SKIP G]
or
current title
(TT)
TT 1 TT 2 TT 3 TT 4
[SKIP H]
[SKIP G]
(If the disc has no chapters.)
will start automatically from the chapter or
2 Playback
title you selected.
Note:
• [SKIP H / G] are not available when playback is stopped.
• Chapter/title search can only be performed during playback or
when the unit has kept the resume information. It cannot be
performed in the stop mode.
• Chapter/title search is not available with some DVD.
30
EN
To play back a single-digit track when there are more
than 10 tracks, press [ENTER] after entering the track
number.
3 Playback will start automatically from the track you
selected.
Note:
• The total number of tracks in your disc;
With less than 10 tracks, press the track number directly.
With 10 or more tracks, to play a single digit track, press [0]
first, then the track number. (e.g., for track 3, press [0] and
[3].) To play a double-digit track, press the track number.
• Track search is not available for programmed or random
playback.
Using [SKIP H / G]
1 During playback, press [SKIP H / G] repeatedly
until your desired track will be selected.
or
current track
(TR)
TR 1 TR 2 TR 3 TR 4
[SKIP H]
[SKIP G]
2 Playback will start automatically from the track you
selected.
Note:
• [SKIP H / G] are not available when playback is stopped.
• Track search can only be performed during playback or
when the unit has kept the resume information. It cannot be
performed in the stop mode.
INTRODUCTION
5 Repeat Playback
Time Search
You can repeat playback chapters, titles or tracks on a disc.
1
playback, press [MODE] repeatedly until
1 During
“ “ appears.
OFF
e.g.) DVD
CONNECTION
During playback, press [MODE] repeatedly until
“
“/“
“ appears.
(REPEAT)
_ _ /12 (SEARCH)
or
TOTAL
“ appears.
DVD
OFF
(repeat off)
CHAPTER
(current chapter repeat)
TITLE
(current title repeat)
OFF
(repeat off)
TRACK
(current track repeat)
ALL
(entire disc repeat)
1:29:00
time lapse within 60 seconds.
WATCHING TV
3 Press [the Number buttons] to select your desired
TOTAL
INITIAL SETTING
2 Use [Cursor K / L] repeatedly until “
2 Press [Cursor K / L] to change the repeat mode.
CD
1:29:00
selected.
OPTIONAL SETTING
4 Playback will start automatically from the time you
3 Press [RETURN] to exit.
Note:
OPERATING DVD
• When there is no need to enter a number, “0” appears
automatically. For example, “0: 0_ : _ _” appears in time
search menu if the total time of the title or track is less than 10
minutes.
• Press [CLEAR] to erase the incorrect input at step 3.
• Time search can only be performed during playback or
when the unit has kept the resume information. It cannot be
performed in the stop mode.
5 Repeat A-B Playback
You can repeat playback between A and B on a disc.
playback, press [MODE] repeatedly until
1 During
“
OFF” appears.
A B
DVD SETTING
Direct Search
2 Press [ENTER] at your desired starting point (A).
A B
Press [the Number buttons] to select your desired
chapter, title or track.
A-
(A-B REPEAT)
A B
Note:
• Point B should be in the same title or track as point A.
• Within a few seconds, the section A-B will begin to
play back repeatedly.
To cancel repeat A-B playback, press [MODE]
4 repeatedly
until “
A-B“ appears.
A B
Press [ENTER] so “ A
B
OFF” appears.
INFORMATION
• To select a single-digit chapter, title, track number, press the
number directly.
• To select double digit chapter, title, track number:
- If the disc contains more than 9 and less than 100 chapter, title,
tracks, press [+10/+100] first, then enter the double digit chapter,
title, track number.
(e.g., for track 26, press [+10/+100], [2] and [6].)
A-B (A-B REPEAT)
TROUBLESHOOTING
3 Press [ENTER] at your desired ending point (B).
31
EN
OPERATING DVD
Note:
Note:
• Repeat setting (except “ALL“) will be cleared when moving to
another title, chapter or track.
• During programmed playback, repeat setting will be effective
for the tracks in the program.
• Repeat playback or repeat A-B playback may not available
with some discs.
• Repeat A-B playback does not function during other repeat
mode.
• To cancel point A, press [CLEAR] at step 2 in “Repeat A-B
Playback“
• Stopping playback will cancel repeat A-B playback.
5 Programmed Playback
CD
You may determine the order in which tracks will be play back.
1 In stop mode, press [MODE] repeatedly until the
“PROGRAM” menu appears.
PROGRAM
CD-DA
T
T
T
T
T
T
T
ENTER
1
2
3
4
5
6
7
TOTAL
1/ 1
1/ 3
PLAY
CLEAR
0:00:00
3:31
4:28
4:19
3:58
4:12
4:02
3:55
T 1 3:31
2 Use [Cursor K / L] to select a desired track, then press
[ENTER] to store.
• Additional tracks may be on other screens. Use
[Cursor K/ L] to go on to the next/previous pages.
• Repeat this step until you have selected all the tracks
you wish to play back in the program.
PROGRAM
CD-DA
TOTAL
0:08:22
T 15 3:18
T 16 4:24
ALL CLEAR
T 4
T 16
3:58
4:24
or
ENTER
PLAY
CLEAR
3/ 3
• Press [CLEAR] to erase the last track in the program if you
make an error.
• To erase all programmed tracks at once, select “ALL CLEAR’’
and press [ENTER] at step 2.
• While a program is being played back, [STOP C] works as
follows:
- Pressing [STOP C] once: The track will be in the resume
standby mode. Next time you press [PLAY B], the playback
will resume from the point where it is stopped in the
programmed playback.
- Pressing [STOP C] twice: Resume mode will be canceled.
Next time you press [PLAY B], playback will restart from the
first track in the original order. However, your programmed
playback can be restarted when you follow the above steps.
(Your programs are still stored until either the disc is ejected
or the unit is turned off.)
On some discs, [STOP C] will not work while the resume
message appears. Please wait until the message disappears.
• To repeat the current track in the program, follow the steps 1
and 2 in “Repeat Playback“ on page 31 and select
“
TRACK“.
• To repeat the entire program, follow the steps 1 and 2 in
“Repeat Playback“ on page 31 and select “
ALL“.
• Turning off the unit or ejecting the disc will erase the
program.
• You cannot use [the Number buttons] to select another
track during programmed playback. Use [SKIP j/ i] to
select other tracks in the program.
• You cannot combine random playback with programmed
playback.
• You cannot alter a programmed order during playback.
• You can start programmed playback only while in
“PROGRAM “ menu.
5 Random Playback
CD
This function shuffles the playing order of tracks instead of playback in the
sequence.
1/ 1
T 16 4:24
• Up to 99 tracks can be ordered.
• If 8 or more tracks were in a program, use
[SKIP H / G] to see all the tracks.
1 In stop mode, press [MODE] repeatedly until
“RANDOM” menu appears.
RANDOM
CD-DA
TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
3 Press [PLAY B] to start programmed playback.
PLAY
2 Press [PLAY B] to start random playback.
Note:
• To repeat the current track in the random mode, follow the
steps 1 and 2 in “Repeat Playback“ on page 31 and select
“
TRACK“.
• To repeat the entire random selections, follow the steps 1 and
2 in “Repeat Playback“ on page 31 and select “
ALL“.
• Random playback will be kept until you press [STOP C].
32
EN
You can check the information about the current disc by pressing [DISPLAY] on
the remote control.
INTRODUCTION
5 On-screen Display
CD
current playback status
appears only when multiangle is available on the DVD
1
4/12 0:03:21 - 0:02:15
T
remaining time of the current
track
elapsed time of the current track
current playback status
1
11/16 0:00:00 - 0:03:30
TR (Track):
current track number /
total tracks
2
4/12 0:13:45 - 0:45:40
current repeat setting
appears only when the
repeat setting is active
T : Track repeat
A : All tracks repeat
A B : A-B repeat
remaining time of the entire disc
0:00:00 - 1:23:45
remaining time of the current title
elapsed time of the current title
OPTIONAL SETTING
TT (title):
current title number / total titles
3
T
ALL:
current track number /
total tracks
WATCHING TV
1/3
INITIAL SETTING
remaining time of the current
chapter
elapsed time of the current
chapter
CH (chapter):
current chapter number /
total chapters
2
CONNECTION
DVD
elapsed time of the entire disc
3
T L1
• When you are playing a disc in program or random mode,
“
PROGRAM” (or “
RANDOM”) will be displayed
instead of 2 .
DVD SETTING
current repeat setting appears
only when the repeat setting is
active
C : Chapter repeat
T : Title repeat
A B : A-B repeat
bit rate indication for the amount
of audio and video data currently
being read
Note:
OPERATING DVD
layer number appears only when
playing a 2-layered disc
L0 : Layer 0 is playing
L1 : Layer 1 is playing
4
TROUBLESHOOTING
Note:
• Some DVD will not allow you to set chapter playback correctly.
INFORMATION
33
EN
OPERATING DVD
5 Special Settings
Subtitle Language
DVD
DVD
This unit allows you to select a subtitle language (if available) during DVD
playback.
1 During playback, press [MODE] repeatedly until
“
Audio Language
“ appears.
This unit allows you to select an audio language (if multiple languages are
available) during DVD playback.
During playback, press [AUDIO] repeatedly
until the desired language appears.
1.ENG Dolby D 3/2.1ch 48k/3
2 Use [Cursor K / L] repeatedly until your desired
language appears.
1.ENG/6 (SUBTITLE)
or
audio can be varied on
the displayed number.
current audio language.
• Each time you press [AUDIO], the audio language
changes as example below.
ENG
(English audio)
• Each time you press [Cursor K / L], the subtitle
language changes as example below.
OFF
(no subtitles)
(English subtitles)
FRE
(French subtitles)
FRE
(French audio)
• Some discs will only allow you to change the audio setting
from the disc menu. Refer to the manual accompanying the
discs for details.
• If your language is not shown after pressing [AUDIO] several
times, the disc may not have that language. However, some
discs allow you to change multiple audio languages setting
in the disc menu. (Operation varies depending on the disc, so
refer to the manual along with the disc.)
• When “NOT AVAILABLE“ appears on the TV screen, it means
audio language is not available.
To cancel the subtitle
1 During playback, press [MODE] repeatedly until
“
(Spanish audio)
Note:
...
ENG
SPA
...
subtitles can be varied on
the displayed number.
current subtitles language.
“ appears.
Camera Angles
1.ENG/6 (SUBTITLE)
DVD
2 Use [Cursor K / L] repeatedly until “
OFF
(SUBTITLE)“ appears.
or
OFF (SUBTITLE)
Some DVD may contain scenes which have been shot
simultaneously from various angles. You can change the
camera angle if “ ” appears on the TV screen. If “ANGLE ICON”
is set to “OFF” in “OTHERS” menu, “ ” will not appear.
(Refer to page 41.)
1 During playback, press [MODE] repeatedly until
“
“ appears.
Note:
• If your language is not shown after pressing [Cursor K / L]
several times, the disc may not have that language. However,
some discs only allow you to change subtitle languages
setting in the disc menu. (Operation varies depending on the
disc, so refer to the manual along with the disc.)
• When “NOT AVAILABLE” appears on the TV screen, it means
no subtitle is recorded on the scene.
• If you choose a language that has 3-letter-abbreviation, the
abbreviation will be displayed every time you change the
subtitle language setting. If you choose any other languages,
“---” will be displayed instead. (Refer to page 42.)
• Ejecting the disc will cancel your subtitle setting.
34
EN
2 Use [Cursor K / L] repeatedly until your desired
camera angle appears.
1 / 8 (ANGLE)
or
angles can be varied on
the displayed number.
INTRODUCTION
Virtual Surround
Black Level Setting
CONNECTION
You can enjoy virtual surround on your existing 2 channel stereo system.
DVD
Adjust the black level to make the dark areas of the TV picture brighter.
1 During playback, press [MODE] repeatedly until
“
“ appears.
1 During playback, press [MODE] repeatedly until
“
“ appears.
2 Use [Cursor K / L] to adjust the black level.
ON (BLACK LEVEL)
ON : Makes the dark areas brighter.
OFF : Shows the original picture as recorded.
2 Use [Cursor K / L] to select the sound level.
or
1 (SURROUND)
1
: Natural effect
2
: Emphasized effect
OFF : No effects (original sound)
OPTIONAL SETTING
3 Press [RETURN] to exit.
OFF (SURROUND)
WATCHING TV
or
INITIAL SETTING
OFF (BLACK LEVEL)
3 Press [RETURN] to exit.
Note:
Stereo Sound Mode
Note:
OPERATING DVD
• The setting will be kept even if the unit is turned off.
• The setting will be kept even if the unit is turned off.
• For audio CD, virtual surround will not be effective if the
sound mode is set to something other than “STEREO”.
See “Stereo Sound Mode”.
• Turn down the level or select “OFF” if the sound is distorted.
CD
DVD SETTING
This unit allows you to select a sound mode during audio CD playback.
During playback, press [AUDIO] repeatedly until the
desired sound mode appears.
STEREO
TROUBLESHOOTING
• Each time you press [AUDIO], the sound mode
changes as example below.
STEREO (stereo sound with left and right channels)
(left channel sound only)
R-ch
(right channel sound only)
INFORMATION
L-ch
Note:
• Virtual surround cannot be changed when the sound mode is
set to either “L-ch” or “R-ch”.
35
EN
OPERATING DVD
Marker Setup
This feature allows you to assign a specific point on a disc to be called back
later.
To set a marker
To return to the marker later
1 During playback, press [MODE] repeatedly until
1 To select a desired marker, repeat steps 1-3 in
“
”/“
” appears.
“To set a marker“.
e.g.) DVD
_ _ /12 (SEARCH)
2 Use [Cursor K /L] repeatedly until maker search menu
appears.
e.g.) DVD
or
[ENTER] at the desired marker to start playback
2 Press
from the specific point which you set.
e.g.) DVD
e.g.) DVD
or
Note:
[Cursor s / B] to select an available marker within
3 Use
60 seconds.
e.g.) DVD
or
the playback reaches the point at which you
4 When
want to set a marker, press [ENTER].
• Marker is now set.
e.g.) DVD
5 Press [RETURN] to exit.
36
EN
• Maker Search menu will disappear in about 60 seconds when
there is no input.
• You can mark up to 10 points.
• To clear a marker, select the marker to be cleared, and then
press [CLEAR].
• Ejecting the disc or turning off the power will erase all
markers.
• Selecting “ ” at step 3 in the section “To set a marker”
or “To return to the marker later” will also erase all
markers.
INTRODUCTION
DVD SETTING
Settings are only effective when the unit is in DVD mode and any discs should not be played back.
QUICK MENU AT A GLANCE
SETUP
[ENTER].
[AUDIO] *1, *2
(Default: ORIGINAL)
Select the desired audio language.
QUICK
TV MODE
DOLBY DIGITAL
6 Use [Cursor K /L] to select the desired item, then press
4:3 LETTER BOX
BITSTREAM
SETUP
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
5 DVD Language Setting
ORIGINAL
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
SELECT:K/L
EXIT:SETUP
You can change the desired language when playing back the disc.
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
[SUBTITLE] *1, *2
(Default: OFF)
Select the desired subtitle language.
SETUP
or
--- TV SETUP --[ENGLISH]
[BRIGHT]
[NORMAL]
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
[DISC MENU] *1
(Default: ENGLISH)
Select the desired language in DVD menu.
SETUP
or
3 Use [Cursor K/L] to select “CUSTOM”, then press [ENTER].
OPERATING DVD
LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
LANGUAGE
SUBTITLE
OFF
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
OPTIONAL SETTING
2 Use [Cursor K/L] to select “DVD SETUP”, then press [ENTER].
or
SET:ENTER
CANCEL:RETURN
WATCHING TV
1 In stop mode, press [SETUP] to display “TV SETUP”.
LANGUAGE
AUDIO
INITIAL SETTING
or
CONNECTION
If you make setting for “TV MODE“ or “DOLBY DIGITAL”, you
can also enter from the “QUICK“ menu. Use [Cursor K /L] to
select “QUICK” and press [ENTER] at step 3.
LANGUAGE
DISC MENU
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
DUTCH
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
SETUP
QUICK
CUSTOM
INITIALIZE
Note:
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
SETUP
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
SET:ENTER
CANCEL:RETURN
5 Use [Cursor K/L] to select the desired item, then press
[ENTER].
SETUP
or
INFORMATION
SELECT:K/L
EXIT:SETUP
• To change the on-screen language, call up “TV SETUP” menu
by pressing [SETUP] once and set the desired language.
(Refer to “Language Selection“ on page 15.)
*1
• Language options are not available with some discs.
• If “OTHER” is selected in “AUDIO”, “SUBTITLE” or “DISC MENU”
menu, press 4-digit number to enter the code for the desired
language. (Refer to “Language Code List” on page 42.)
• Only the languages supported by the disc can be selected.
*2
• Use [MODE] to select subtitles available on the DVD.
• Use [AUDIO] to select audio available on the DVD.
• If the DVD’s default settings for audio and subtitle are the
same language, the subtitles may not show unless you turn
them on.
TROUBLESHOOTING
4 Use [Cursor K/L] to select “LANGUAGE”, then press [ENTER].
or
DVD SETTING
or
7 Press [SETUP] to exit.
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
SELECT:K/L
EXIT:SETUP
ORIGINAL
OFF
ENGLISH
SET:ENTER
CANCEL:RETURN
37
EN
DVD SETTING
5 Display Setting
You can change the TV aspect ratio and still mode clarity in “DISPLAY”
menu.
1 In stop mode, press [SETUP] to display “TV SETUP”.
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
6 Use [Cursor K /L] to select the desired item, then press
[ENTER].
[TV MODE]
(Default: 4:3 LETTER BOX)
Select the desired TV aspect ratio.
SETUP
or
DISPLAY
TV MODE
4:3 LETTER BOX
4:3 PAN & SCAN
SELECT:K/L
EXIT:SETUP
2 Use [Cursor K /L] to select “DVD SETUP”, then press
SET:ENTER
CANCEL:RETURN
[ENTER].
[STILL MODE]
or
Select the desired still mode.
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
(Default: AUTO)
[ENGLISH]
[BRIGHT]
[NORMAL]
SETUP
or
3 Use [Cursor K /L] to select “CUSTOM”, then press
DISPLAY
STILL MODE
AUTO
FEILD
FRAME
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
[ENTER].
Note:
SETUP
or
QUICK
CUSTOM
INITIALIZE
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
4 Use [Cursor K /L] to select “DISPLAY”, then press
[ENTER].
SETUP
or
CUSTOM
7 Press [SETUP] to exit.
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
5 Use [Cursor K /L] to select the desired item, then press
[ENTER].
SETUP
or
DISPLAY
TV MODE
STILL MODE
SELECT:K/L
EXIT:SETUP
38
EN
TV MODE:
• Select “4:3 LETTER BOX”, so that black bars may appear on
the top and bottom of the TV screen.
• Select “4:3 PAN & SCAN” for a full height picture with both
sides adjusted.
STILL MODE:
• Select “AUTO” usually.
• If you select “FIELD”, the picture in the still mode will be
stabilized.
• If you select “FRAME”, the picture in the still mode will be
highly defined.
4:3 LETTER BOX
AUTO
SET:ENTER
CANCEL:RETURN
Choose the appropriate audio settings for your equipment. It only affects
during the playback of DVD.
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
[ENTER].
CONNECTION
1 In stop mode, press [SETUP] to display “TV SETUP”.
6 Use [Cursor K /L] to select the desired item, then press
[DRC] (dynamic range control)
(Default: ON)
Set “DRC”.
This function is available only on the discs which are
recorded in the Dolby Digital format.
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
INITIAL SETTING
SETUP
or
ON
ON
BITSTREAM
2 Use [Cursor K /L] to select “DVD SETUP”, then press
[ENTER].
SELECT:K/L
EXIT:SETUP
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
ON : Compress the range between soft and loud
sounds.
OFF : No effects (original sound).
[DOWN SAMPLING]
(Default: ON)
Set “DOWN SAMPLING”.
This function is available only on digital outputting of a
disc recorded in 96kHz.
[ENTER].
SETUP
or
SETUP
or
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
4 Use [Cursor K /L] to select “AUDIO”, then press
SETUP
or
ON : When outputting in 48kHz.
OFF : When outputting the original sound.
Note:
• When playing back a 96 kHz disc with the copyright
protection or when virtual surround is set to 1 or 2, the
sound will be down sampled at 48 kHz even if “DOWN
SAMPLING” is “OFF”.
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
[DOLBY DIGITAL]
SET:ENTER
CANCEL:RETURN
(Default: BITSTREAM)
Set “BITSTREAM“ when this unit is connected to a
Dolby Digital decoder. Available on DVD only.
SETUP
5
Use [Cursor K /L] to select the desired item, then press
[ENTER].
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
BITSTREAM
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
SELECT:K/L
EXIT:SETUP
ON
ON
BITSTREAM
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
INFORMATION
SETUP
or
or
TROUBLESHOOTING
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
DVD SETTING
[ENTER].
ON
ON
BITSTREAM
OPERATING DVD
QUICK
CUSTOM
INITIALIZE
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
OPTIONAL SETTING
3 Use [Cursor K /L] to select “CUSTOM”, then press
SET:ENTER
CANCEL:RETURN
WATCHING TV
or
INTRODUCTION
5 DVD Audio Setting
SET:ENTER
CANCEL:RETURN
BITSTREAM : Outputs Dolby Digital signals.
PCM
: Converts the Dolby Digital into PCM.
(2 channel)
7 Press [SETUP] to exit.
39
EN
DVD SETTING
5 Parental Setting
Parental setting prevents your children from viewing inappropriate materials.
(password protected.) Playback will stop if the ratings exceed the levels you set.
7 Use [Cursor K /L] to select the desired item, then press
[ENTER].
1 In stop mode, press [SETUP] to display “TV SETUP”.
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
SETUP
or
[ENGLISH]
[BRIGHT]
[NORMAL]
PARENTAL
PARENTAL LEVEL
ALL
8 [ADULT]
7 [NC-]7
6 [R]
5 [PGR]
4 [PG13]
3 [PG]
SELECT:K/L
EXIT:SETUP
2 Use [Cursor K/L] to select “DVD SETUP”, then press [ENTER].
or
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
SET:ENTER
CANCEL:RETURN
PARENTAL LEVEL
ALL
: all parental locks are canceled.
8 [ADULT]
: all ratings (adult/general/children) can
be played back.
7 [NC-17]-2 [G] : only DVD intended for general use and
children can be played back.
1 [KID SAFE] : only DVD intended for children can be
played back.
3 Use [Cursor K/L] to select “CUSTOM”, then press [ENTER]. 8 Press [SETUP] to exit.
SETUP
or
QUICK
CUSTOM
INITIALIZE
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
Use [Cursor K /L] to select “PARENTAL”, then press
4 [ENTER].
To change the password
6 Follow steps 1 to 4. Use [Cursor K /L] to select
“PASSWORD CHANGE“, then press [ENTER].
SETUP
SETUP
or
or
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
SELECT:K/L
EXIT:SETUP
SETUP
PARENTAL LEVEL
ALL
PASSWORD CHANGE
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
Use [the Number buttons] to enter the 4-digit
5 number
for your password, then press [ENTER].
PARENTAL
SET:ENTER
CANCEL:RETURN
7 Use [the Number buttons] to enter the new 4-digit
password, then press [ENTER].
PARENTAL
SETUP
PARENTAL
PASSWORD
PASSWORD
Please enter a 4-digit password.
Please enter a 4-digit password.
0
0
0
0
Don’t forget the password.
Press “ENTER” to activate password.
EXIT:SETUP
6
• If you have set password already, use [the Number
buttons] to enter the current 4-digit password.
• You cannot use the default password (4737) to play a DVD.
Use [Cursor K /L] to select “PARENTAL LEVEL“, then
press [ENTER].
SETUP
or
40
EN
CANCEL:RETURN
PARENTAL
PARENTAL LEVEL
ALL
PASSWORD CHANGE
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
EXIT:SETUP
CANCEL:RETURN
Note:
• DVD-video may not respond to parental lock settings. Make
sure this function works with your DVD-video.
• Record the password in case you forget it.
• If you forget the password, press [4], [7], [3], [7], then enter
your new password. Password will be cleared and parental
levels will be set to “ALL”.
• A power failure will not erase your password.
8 Press [SETUP] to exit.
INTRODUCTION
5 Others
You can change the other functions.
6 Use [Cursor K /L] to select the desired item, then press
[ENTER].
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
[ANGLE ICON]
(Default: ON)
Set to “ON” to show the angle icon when multiple
camera angles are available during DVD playback.
2 Use [Cursor K /L] to select “DVD SETUP”, then press
INITIAL SETTING
SETUP
or
OTHERS
ANGLE ICON
SCREEN SAVER
ON
OFF
[ENTER].
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
[ENTER].
SETUP
or
OPTIONAL SETTING
3 Use [Cursor K /L] to select “CUSTOM”, then press
[SCREEN SAVER]
(Default: OFF)
If you select “ON”, the screen saver program starts when
there is no input from the unit for 5 minutes in stop
mode.
OTHERS
ANGLE ICON
SCREEN SAVER
ON
OFF
SETUP
or
QUICK
CUSTOM
INITIALIZE
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
OPERATING DVD
SELECT:K/L
EXIT:SETUP
WATCHING TV
or
CONNECTION
1 In stop mode, press [SETUP] to display “TV SETUP”.
7 Press [SETUP] to exit.
4 Use [Cursor K /L] to select “OTHERS”, then press
[ENTER].
DVD SETTING
SETUP
or
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
TROUBLESHOOTING
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
5 Use [Cursor K /L] to select the desired item, then press
[ENTER].
SETUP
OTHERS
ANGLE ICON
SCREEN SAVER
SELECT:K/L
EXIT:SETUP
INFORMATION
or
ON
OFF
SET:ENTER
CANCEL:RETURN
41
EN
DVD SETTING
5 Reset to the Default Setting
5 Language Code List
You can reset all the settings except for the parental setting and
on-screen menu language.
Language
1 In stop mode, press [SETUP] to display “TV SETUP”.
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
2 Use [Cursor K /L] to select “DVD SETUP”, then press
[ENTER].
or
--- TV SETUP --LANGUAGE
BACK LIGHT
COLOR TEMP.
DVD SETUP
[ENGLISH]
[BRIGHT]
[NORMAL]
3 Use [Cursor K /L] to select “INITIALIZE”, then press
[ENTER].
SETUP
or
QUICK
CUSTOM
INITIALIZE
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
4 Use [Cursor K /L] to select “YES”, then press [ENTER].
SETUP
or
INITIALIZE
Initialize?
NO
YES
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
Note:
• When you want to cancel the initialization, select “NO” at
step 4, then press [SETUP].
5
Press [SETUP] to exit.
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech [CZE]
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Code
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
Language
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish [POL]
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Note:
• If you choose a language that has a 3-letter abbreviation,
they will be displayed every time you change the audio
or subtitle language setting above. If you choose any
other language, ‘---’ will be displayed instead. (3-letter
abbreviation is written in bracket.)
42
EN
INTRODUCTION
TROUBLESHOOTING
5 Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart
once before calling for service.
No color
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Adjust the “COLOR” in the main menu.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
T
V Picture blurred
OPERATING DVD
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on again.
OPTIONAL SETTING
No picture or sound
WATCHING TV
• Be sure the power cord is plugged in.
• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
reset itself.
INITIAL SETTING
Remedy
No power
CONNECTION
Symptom
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on
screen
• Move the unit away from nearby electric appliances. Turn off the power and wait
30 minutes before turning it back on.
• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some
channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor
• View other TV channels. The problem might be limited to the broadcasting station.
No reception of digital signals
• Make sure auto channel scan has been completed (Refer to “Auto Channel Scan” on
page 14).
Auto channel scan must be completed when you set up the unit for the first time
or move it to a location where previously unavailable channels are broadcast.
• The selected channel may not be broadcasting.
• When auto channel scan is interrupted and not completed, some channels will not
be received. Make sure to complete (Refer to “Auto Channel Scan” on page 14).
INFORMATION
Bars on screen
TROUBLESHOOTING
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
DVD SETTING
Ghosts in picture
43
EN
TROUBLESHOOTING
Symptom
Remedy
The entered channel number
changes automatically
• Many digital channels have alternate channel numbers. The unit changes the numbers
automatically to the ones signifying the broadcasting stations. These are the numbers used
for analog broadcasts.
Remote control does not work
• Check the antenna or cable connection to the main unit.
• Check the batteries of the remote control.
• Check if there is an obstacle between the infrared sensor window and the remote
control.
• Test the signal output. If OK, then possible remote sensor trouble.
(Refer to “IR Signal Check” on page 45.)
• Aim the remote control directly at the infrared sensor window on the front of the unit.
• Reduce the distance to the unit.
• Re-insert the batteries with their polarities (+/– signs) as indicated.
Problems with Closed Caption Feature
T Misspelled captions are
displayed.
V Captions are not entirely
displayed, or captions are
delayed behind the dialogue.
• Closed captioning production companies may broadcast programs without
correcting the misspelling in a live broadcast.
• Captions that are delayed a few seconds behind the actual dialogue are common for
live broadcasts. Most captioning production companies can display a dialogue to a
maximum of 220 words per minute. If a dialogue exceeds that rate, selective editing is
used to insure that the captions remain up-to-date with the current TV screen dialogue.
Captions are displayed as a
white box.
No caption is displayed in the
Closed Caption-supported
program.
• Interference from buildings or weather conditions may cause captioning to be
incomplete.
• Broadcasting station may shorten the program to insert advertisement. The closed
caption decoder cannot read the information of the shortened program.
No caption is displayed
when playing the videotape
containing captions.
• The videotape may be illegally copied, or the caption signal might not have been
read during copying.
Black box is displayed in the
screen.
• “Text” mode is selected for caption. Select “CAPTION1”, “CAPTION2” or “OFF”.
Completely distorted picture
or black/white picture with
DVD
• Make sure the disc is compatible with the unit.
Picture freezes momentarily
during playback.
• Check the disc for finger prints/scratches and clean with a soft cloth wiping from
center to edge.
Disc cannot be played.
• Clean the disc.
• Ensure the disc is correctly inserted.
• Check if the disc is defective by trying another disc.
• Cancel the parental lock or change the control level.
• Insert a correct disc that plays on this unit.
• Handle a disc with special care so that it does not have fingerprints, scratches, or
dusts on its surface.
D
V
Buttons do not work or the
D unit stops responding.
The unit does not respond to
some operating commands
during playback.
• To completely reset the unit, unplug the power cord from the power outlet for
5-10 seconds.
• Operations may not be permitted by the disc. Refer to the instructions of the disc.
Angle does not switch.
• The angle cannot be switched for DVD which do not contain multiple angles. In
some cases multiple angles are only recorded for specific scenes.
Playback does not start
when the title is selected.
• Check the “PARENTAL” setting.
The password for rating level
has been forgotten.
• Enter the default password “4737”, then your forgotten password will be cleared.
Note:
• The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a fixed point of
blue, green or red. This is not to be considered a defect in the LCD screen.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this owner’s manual for more
details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
44
EN
INTRODUCTION
INFORMATION
5 Glossary
Dolby Digital
Region Code
Acronym that stands for Advanced Television
Systems Committee and the name of the
digital broadcasting standards.
The system developed by Dolby Laboratories
to compress digital sound. It offers stereo
sound (2ch) or multi-channel audio.
Aspect ratio
EDTV (enhanced definition TV)
The width of a TV screen relative to its
height. Conventional TVs are 4:3 (in other
words, the screen is almost square);
widescreen models are 16:9 (the screen is
almost twice as wide as its height).
Enhanced digital format that takes 480-line
progressive signal.
Regions associate discs and players with
particular areas of the world. This unit will
only play back discs that have compatible
region codes. You can find the region code
of your unit by looking on the rear panel.
Some discs are compatible with more than
one region (or all regions).
HDTV (high definition TV)
SAP (secondary audio program)
Ultimate digital format that produces high
resolution and high picture quality.
Second-audio channel delivered separately
from main-audio channel. This audio
channel is used as an alternate in bilingual
broadcasting.
NTSC
Acronym that stands for National Television
Systems Committee and the name of the
current analog broadcasting standards.
Password
A stored 4-digit number that allows access
to parental control features.
SDTV (standard definition TV)
Standard digital format that is similar to the
NTSC picture quality.
S-video
OPTIONAL SETTING
Offers higher quality images by delivering
each signal, color (c) and luminance (y)
independently of each other through
separate cables.
5 Maintenance
Cabinet Cleaning
Disc Handling
• Handle the discs so that fingerprints and dust do not adhere to the
surfaces of the discs.
OPERATING DVD
• Wipe the front panel and other exterior surfaces of the unit with a soft
cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the unit.
Such chemicals may cause damage and discoloration to the exposed surfaces.
Servicing
• Always store the disc in its protective case when it is not used.
• To clean-off, use a soft cloth.
• Do not use a hard cloth since this will mar the disc.
• Wipe the disc in a straight line from center to edge.
• Never wipe with a circular motion.
DVD SETTING
Should your unit become inoperative, do not try to correct the problem
yourself. There are no user serviceable parts inside. Turn off the unit,
unplug the power cord and call our toll free customer support line found on
the cover of this manual to locate an authorized service center.
Panel Cleaning
Wipe the panel with a soft cloth. Before cleaning the panel, disconnect the
power cord.
• If the unit still does not perform properly when it is operated, while
referring to the relevant sections and to "Troubleshooting Guide" in this
owner’s manual, the laser optical pickup unit may be dirty. Consult your
dealer or an Authorized Service Center for inspection and cleaning of the
laser optical pickup unit.
TROUBLESHOOTING
If the Laser Optical Pickup Unit is Dirty
WATCHING TV
This is a video signal format that conveys
each of 3 principal colors of light (red,
blue and green) through different signal
lines. This allows the viewers to experience
picture colors as original as it is. There are
several signal formats, including Y / Pb / Pr
and Y / Cb / Cr.
INITIAL SETTING
Component Video
CONNECTION
ATSC
• Do not use detergent or abrasive cleaning agents.
IR Signal Check
• With a digital camera
(including built-in cell
phone cameras)
Point a digital camera towards the remote control.
Push any button on the remote control and look
through the digital camera. If the infrared light
appears through the camera, the remote control is
working.
INFORMATION
If the remote control is not working properly, you can use an AM radio or
digital camera (including a cellular phone with built-in camera) to see if it
is sending out an infrared signal.
• With an AM radio:
Tune the AM radio station to a non-broadcasting
frequency. Point the remote control towards it,
push any button and listen. If the sound from
the radio flutters, it is receiving the remote
control’s infrared signal.
45
EN
INFORMATION
5 Cable Channel Designations
If you subscribe to cable TV, the channels are displayed as 1-135.
Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company.
The following is a chart of common cable channel designations.
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
5A
1
I
22
W+7
43
W+28
64
W+49
85
W+65
106
W+86
127
2
2
J
23
W+8
44
W+29
65
W+50
86
W+66
107
W+87
128
3
3
K
24
W+9
45
W+30
66
W+51
87
W+67
108
W+88
129
4
4
L
25
W+10
46
W+31
67
W+52
88
W+68
109
W+89
130
5
5
M
26
W+11
47
W+32
68
W+53
89
W+69
110
W+90
131
6
6
N
27
W+12
48
W+33
69
W+54
90
W+70
111
W+91
132
7
7
O
28
W+13
49
W+34
70
W+55
91
W+71
112
W+92
133
8
8
P
29
W+14
50
W+35
71
W+56
92
W+72
113
W+93
134
9
9
Q
30
W+15
51
W+36
72
W+57
93
W+73
114
W+94
135
10
10
R
31
W+16
52
W+37
73
W+58
94
W+74
115
5 General Specifications
12
12
T
33
W+18
54
W+39
75
A-4
96
W+76
117
13
13
U
34
W+19
55
W+40
76
A-3
97
W+77
118
A
14
V
35
W+20
56
W+41
77
A-2
98
W+78
119
ATSC / NTSC-M TV Standard
Closed caption system:
§15.122/FCC (Digital CC)
§15.119/FCC (Analog CC)
Channel coverage (ATSC/NTSC):
VHF: 2 ~ 13
UHF: 14 ~ 69
CATV: 2 ~ 13, A ~ W, W+1 ~ W+94,
(analog W+1 ~ W+84), A-5 ~ A-1, 5A
Tuning system:
Channel frequency
synthesized tuning system
Channel access:
Direct access keyboard,
Programmable scan, and up/down
DVD
Discs (playback compatibility):
DVD Video, DVD-RW/-R,
DVD+RW/+R, audio CD, CD-RW/-R
Frequency response:
DVD (linear sound): 20 Hz to 20 kHz (sample rate: 48 kHz)
20 Hz to 44 kHz (sample rate: 96 kHz)
CD:
20 Hz to 20 kHz
Signal-to-noise ratio (S/N ratio):
CD:
75 dB (JEITA)
Total distortion factor:
DVD:
1 kHz 0.008% (JEITA)
CD:
1 kHz 0.008% (JEITA)
B
15
W
36
W+21
57
W+42
78
A-1
99
W+79
120
C
16
W+1
37
W+22
58
W+43
79
W+59
100
W+80
121
D
17
W+2
38
W+23
59
W+44
80
W+60
101
W+81
122
E
18
W+3
39
W+24
60
W+45
81
W+61
102
W+82
123
F
19
W+4
40
W+25
61
W+46
82
W+62
103
W+83
124
G
20
W+5
41
W+26
62
W+47
83
W+63
104
W+84
125
H
21
W+6
42
W+27
63
W+48
84
W+64
105
W+85
126
5 Electrical Specification
Sound output:
TV
Television Format:
11
11
S
32
W+17
53
W+38
74
A-5
95
W+75
116
1W, 8Ω x 2
5 Other Specifications
Terminals:
Antenna input:
VHF/UHF/CATV
75Ω unbalanced (F-type)
Video input:
RCA jack x 1
1 Vp-p (75Ω)
Audio input:
RCA jack x 4
2V rms
(input impedance: more than 22kΩ)
S-Video input:
Mini DIN 4-pin jack x 1 Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
Component video input:
RCA jack x 3
Y: 1 Vp-p (75Ω)
Pb: 700mVp-p (75Ω)
Pr: 700mVp-p (75Ω)
Digital audio coaxial output:
Pin jack x 1: 500mVp-p
1
Headphone:
/8 inches (3.5mm)
Remote control:
Digital encoded
infrared light system
Operating temperature:
41°F (5°C) to 104°F (40°C)
Power requirements: 120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption (Maximum):
65W
LCD:
20 inches
Dimensions:
H
W
D
Weight:
13.0 lbs.
: 17.9 inches
: 23.4 inches
: 8.1 inches
(454mm)
(594mm)
(204mm)
(5.9 kg)
• Designs and specifications are subject to change without notice and
without our legal obligation.
• If there is a discrepancy between languages, the default language will
be English.
46
EN
MEMO
47
EN
TM
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
LABOR:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year
from the date of original retail purchase. Certain parts and LCD image burn-in are excluded
from this warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the
date of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO
OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,
missing or if service was attempted by an unauthorized service center. This limited warranty does not
apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during
normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs,
alterations or products not supplied by FUNAI CORP., or damage, which results from accident, misuse,
abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use
such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or
other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL),
ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING
THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY
DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO
PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE
CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY
FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN
SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its
original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE
CENTER. FUNAI CORP. will not reimburse you for any service done by unauthorized service providers
without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact us at:
FUNAI CORPORATION
Customer Service
Tel : 1-800-256-2487
http://www.EmersonAudioVideo.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in China
A7441UH
1EMN22105 *****