Samsung SV-640B/XSA Service manual

http://www.aldiarman.blogspot.com/
LCD-Monitor
Chassis
Model
LS19HAA
940N
19"
SERVICE
LCD Monitor
Manual
Fashion Feature
-Lustrous/Colorful Appearance (Design)
-Integrated UI applied
-Built-in Scaler Sync Separator
-Connectivity : Analog (15p Dsub),
Dual (24p DVI-D)
-Power Consumption : 19"(38W)
-DPMS : under 1 W (230Vac)
http://www.aldiarman.blogspot.com/
-This Service Manual is a property of Samsung
Electronics Co., Ltd.
Any unauthorized use of Manual can be punished
under applicable International and/or domestic
law.
Samsung Electronics Co.,Ltd.
416, Maetan-3Dong, Yeongtong-Gu, Suwon City,
Gyeonggi-Do, Korea, 443-742
Printed in Korea
P/N : BN82-00133M-00
URL : http://itself.sec.samsung.co.kr/
http://www.aldiarman.blogspot.com/
1 Precautions
1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock.
1-1 Safety Precautions
1-1-1 Warnings
1.
For continued safety, do not attempt to modify the circuit
board.
2.
Disconnect the AC power and DC power jack before
servicing.
1-1-2 Servicing the LCD Monitor
1.
When servicing the LCD Monitor, Disconnect the AC
line cord from the AC outlet.
2.
It is essential that service technicians have an accurate
voltage meter available at all times. Check the
calibration of this meter periodically.
1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the
following safety checks:
1.
Inspect each lead dress to make certain that the leads are
not pinched or that hardware is not lodged between the
chassis and other metal parts in the monitor.
2.
Inspect all protective devices such as nonmetallic control
knobs, insulating materials, cabinet backs, adjustment
and compartment covers or shields, isolation resistorcapacitor networks, mechanical insulators, etc.
3.
Leakage Current Hot Check (Figure 1-1):
WARNING : Do not use an isolation
transformer during this test.
Use a leakage current tester or a metering system that
complies with American National Standards Institute
(ANSI C101.1, Leakage Current for Appliances), and
Underwriters Laboratories (UL Publication UL1410,
59.7).
Figure 1-1. Leakage Current Test Circuit
4.
With the unit completely reassembled, plug the AC line
cord directly into a 120V AC outlet. With the unit’s AC
switch first in the ON position and then OFF, measure
the current between a known earth ground (metal water
pipe, conduit, etc.) and all exposed metal parts,
including: metal cabinets, screwheads and control shafts.
The current measured should not exceed 0.5 milliamp.
Reverse the power-plug prongs in the AC outlet and
repeat the test.
1-1-4 Product Safety Notices
Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual
inspection. The protection they give may not be obtained by
replacing them with components rated for higher voltage,
wattage, etc. Parts that have special safety characteristics are
identified by
on schematics and parts lists. A substitute
replacement that does not have the same safety characteristics
as the recommended replacement part might create shock, fire
and/or other hazards. Product safety is under review
continuously and new instructions are issued whenever
appropriate.
1-1
http://www.aldiarman.blogspot.com/
1 Precautions
1-2 Servicing Precautions
WARNING:
An electrolytic capacitor installed with the wrong polarity might explode.
Caution:
Before servicing units covered by this service manual, read and follow the Safety Precautions section
of this manual.
Note:
If unforeseen circumstances create conflict between the following servicing precautions and any of the safety
precautions, always follow the safety precautions.
1-2-1 General Servicing
Precautions
1.
2.
3.
Always unplug the unit’s AC power cord from the AC
power source and disconnect the DC Power Jack before
attempting to:
(a) remove or reinstall any component or assembly, (b)
disconnect PCB plugs or connectors, (c) connect a test
component in parallel with an electrolytic capacitor.
Some components are raised above the printed circuit
board for safety. An insulation tube or tape is sometimes
used. The internal wiring is sometimes clamped to
prevent contact with thermally hot components. Reinstall
all such elements to their original position.
4.
Check the insulation between the blades of the AC plug
and accessible conductive parts (examples: metal panels,
input terminals and earphone jacks).
5.
Insulation Checking Procedure: Disconnect the power
cord from the AC source and turn the power switch ON.
Connect an insulation resistance meter (500 V) to the
blades of the AC plug.
The insulation resistance between each blade of the AC
plug and accessible conductive parts (see above) should
be greater than 1 megohm.
6.
After servicing, always check that the screws,
components and wiring have been correctly reinstalled.
Make sure that the area around the serviced part has not
been damaged.
Always connect a test instrument’s ground lead to the
instrument chassis ground before connecting the positive
lead; always remove the instrument’s ground lead last.
1-3 Static Electricity Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called
Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The
following techniques will reduce the incidence of component damage caused by static electricity.
1.
Immediately before handling any semiconductor
components or assemblies, drain the electrostatic charge
from your body by touching a known earth ground.
Alternatively, wear a discharging wrist-strap device. To
avoid a shock hazard, be sure to remove the wrist strap
before applying power to the monitor.
2.
After removing an ESD-equipped assembly, place it on a
conductive surface such as aluminum foil to prevent
accumulation of an electrostatic charge.
3.
Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage ESDs.
4.
Use only a grounded-tip soldering iron to solder or
desolder ESDs.
5.
Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static” can
generate electrical charges sufficient to damage ESDs.
1-2
6.
Do not remove a replacement ESD from its protective
package until you are ready to install it. Most
replacement ESDs are packaged with leads that are
electrically shorted together by conductive foam,
aluminum foil or other conductive materials.
7.
Immediately before removing the protective material
from the leads of a replacement ESD, touch the
protective material to the chassis or circuit assembly into
which the device will be installed.
Caution:
Be sure no power is applied to the
chassis or circuit and observe all
other safety precautions.
8.
Minimize body motions when handling unpackaged
replacement ESDs. Motions such as brushing clothes
together, or lifting your foot from a carpeted floor can
generate enough static electricity to damage an ESD.
http://www.aldiarman.blogspot.com/
1 Precautions
1-4 Installation Precautions
1. For safety reasons, more than two people are
required for carrying the product.
2. Keep the power cord away from any heat emitting
devices, as a melted covering may cause fire or
electric shock.
3. Do not place the product in areas with poor
ventilation such as a bookshelf or closet. The
increased internal temperature may cause fire.
6. Keep the antenna far away from any high-voltage
cables and install it firmly. Contact with the highvoltage cable or the antenna falling over may
cause fire or electric shock.
7. When installing the product, leave enough space
(10cm) between the product and the wall for
ventilation purposes.
A rise in temperature within the product may
cause fire.
4. Bend the external antenna cable when connecting
it to the product. This is a measure to protect it
from being exposed to moisture. Otherwise, it
may cause a fire or electric shock.
5. Make sure to turn the power off and unplug the
power cord from the outlet before repositioning
the product. Also check the antenna cable or the
external connectors if they are fully unplugged.
Damage to the cord may cause fire or electric
shock.
1-3
http://www.aldiarman.blogspot.com/
2 Product Specifications
2 Product Specifications
2 Product Specifications
2-1 Fashion Feature
- Develop Cost Effective Model
- LCD Monitor Standardization/Develop Concept-leading Product
- Develop New Design & Advanced Stand
- Apply integrated GUI for the user's convenience
2-2 LS19HAB/LS19HAT Specifications
Description
Item
LS19HAB
LS19HAT
LCD Panel
TFT-LCD panel, RGB vertical stripe, normally black transmissive,
19-Inch viewable, 0.264 (H) x 0.264 (V) mm pixel pitch
Scanning Frequency
Horizontal : 30 kHz ~ 81 kHz (Automatic)
Vertical : 56 Hz ~ 75 Hz
Display Colors
16.7 Million colors
Maximum Resolution
Horizontal : 1280 Pixels
Vertical : 1024 Pixels
Input Video Signal
Input Sync Signal
±
Type : Seperate H/V sync, Composite H/V, Sync-on-Green (option), automatic
synchronization without external switch of sync type
Level : TTL level
Maximum Pixel Clock rate
135 MHz
Active Display
Horizontal/Vertical
338 ± 3 mm / 270 ± 3 mm
AC power voltage & Frequency
AC 90 ~ 264 Volts, 60/50 Hz ± 3 Hz
Power Consumption
40W (Max)
Dimensions
Simple-Stand
HAS-Stand
Set (W x D x H)
407.6 x 65.4 x 335.0 mm(Without Stand)
403.6 x 65.4 x 331.9 mm(Without Stand)
407.6 x 217.0 x 421.5 (With Stand)
403.2 x 200.0 x 406.4 mm(With Stand)
4.6 kg
4.9 kg
Weight (Set)
Environmental Considerations
°
°
°
°
- Designs and specifications are subject to change without prior notice.
°
°
°
°
http://www.aldiarman.blogspot.com/
2 Product Specifications
2-3 Option Specification
Item
2-2
Item Name
CODE.NO
Quick Setup Guide
BH68-00376L
Warranty Card
(Not available in all locations)
BH68-70438A
User's Guide,
Monitor Driver,
Natural Color software,
MagicTune¢â software
MagicRotation software
BN59-00390Q
D-Sub(15 Pin)
Cable
BN39-00244B
Power Cord
3903-000042
DVI Cable
BN39-00341A
Remark
Sold separately
http://www.aldiarman.blogspot.com/
3 Alignments and Adjustments
3 Alignments and Adjustments
This section of the service manual explains how to use the RS232 JIG.
This function is needed for AD board change and program memory (IC110) change.
3-1 Required Equipment
The following equipment is necessary for adjusting the monitor:
• Computer with Windows 95, Windows 98, or Windows NT.
• MTI-2031 DDC MANAGER JIG
3-2 Automatic Color Adjustment
To input video, use 16 gray or any pattern using black and white.
1. Select english for OSD language.
2. Press the “
(Enter/Source)” key for 5 seconds.
3-3 DDC EDID Data Input
1. Input DDC EDID data when replacing AD PCB.
2. Receive/Download the proper DDC file for the model from HQ quality control department.
Install the below jig (Figure 1) and enter the data.
MTI-2031
DDC Manager
Parallel Connector
(25P Cable)
Connect Monitor
(Signal Cable)
Figure 1.
3-4 OSD Adjustment When Replacing Panel
1. Adjust brightness and contrast to 0. Then, press the (Enter/Source) key for 5 second.
Service function OSD will appear on screen.
2. Press the + key to place the cursor on the panel. Press the menu key for 5 seconds.
3-5 OSD Adjustment When Replacing Lamp Only
1. Adjust brightness and contrast to 0. Then, press the exit key for 5 seconds.
Service function OSD will appear on the screen.
2. Press the + key. Select upper lamp and press the menu key for 5 seconds.
Then, select lower lamp and press the menu key for 5 seconds.
-Note
: Please be sure to read the following instructions for details on service function.
3-1
http://www.aldiarman.blogspot.com/
3 Alignments and Adjustments
3-6 Service Function Spec.
3-6-1 How to Display Service Function OSD
1. The value for brightness and contrast should be changed to zero.
2. Within 5 seconds, press the (Enter/Source) key.
3. Service function OSD will be displayed.
-If
you want to disable the service function OSD, you will have to power off.
Panel Information
Softward Version
Checksum
Figure 2. The example of service function OSD
The service function OSD is based on a grid of 29 columns x 12 rows.
The service function OSD consists of panel information, software version and MICOM checksum.
3-6-2 How to Control Service Function OSD
1. With the panel selected on OSD, whenever you press the right key, the base color will change to blue from
“Panel” to “Upper Lamp”, “Lower Lamp”.
Figure 3.
3-2
http://www.aldiarman.blogspot.com/
3 Alignments and Adjustments
3-6-3 How to Control Service Function OSD
•After change the panel or lamp, you must reset service function OSD.
•The case of panel change
After changeing the panel, press the menu key within 5 seconds,.
Then, panel Ch. No increases one step and the panel time information is reset to zero.
Simultaneously, other information is reset to zero (Upper/Lower lamp, Panel cycle).
Figure 4.
3-6-4 How to Control Service Function OSD
•In the case of Upper Lamp or Lower Lamp change
After changeing the Upper Lamp or Lower Lamp,
1. Select the Upper Lamp or Lower Lamp
2. Press the Menu key within an 5 seconds.
Then, Ch. No and time will be reset to zero (selected item only).
Figure 5, 6.
3-3
http://www.aldiarman.blogspot.com/
3 Alignments and Adjustments
3-7 How to execute DDC
1
2
3
4
1. Open file.
2. Select Port #1.
3. Select DDC file.
4.Click, "Next" Button
5
5. Type in the monitor serial number and press Enter.
*Repeat this step 2 to 5 times in digital inputs after the analog input.
3-4
http://www.aldiarman.blogspot.com/
4 Troubleshooting
4 Troubleshooting
’
•
•
•
•
•
•
“
”
4-1 No Power (LS19HAA/LS19HAT)
’
Yes
*
When Pin 4 of CN600 is 0V
does proper DC 13V, 5V
appear at Pin 1, 2 and 6, 7 of
CN600 separately?
No
Change IP Board.
Yes
When Pin 4 of IC600 is DC 0.5V
does proper DC 0.5V appear at
Pin 5 and 6 of IC600?
No
Check IC600 and related circuit.
Yes
When Pin 2, 3 of IC601 is
DC 3.3V does proper DC 4.3V
appear at Pin 1 of IC601?
No
Check IC601 and related circuit.
Yes
When Pin 2, 3 of IC601 is
DC 4.3V does proper DC 2.5V
appear at Pin 4 of IC601?
No
Check IC601 and related circuit.
* 0V means power on state.
When the monitor work well except DPMS and power
switch off,
0V should be applied to number 4 of CN600.
4-1
http://www.aldiarman.blogspot.com/
4 Troubleshooting
4-2 No Video (ANALOG)
Check signal cable connection and
power.
1
X400 oscillate properly?
No
Replace or check related circuit.
Yes
Is there R, G, B input at
R101, R103 and R105?
No
Check input part.
Yes
Is there Hsync, Vsync waveform
2
3
No
Check IC400 and related circuit.
at Pin 100, 1 of IC 400?
Yes
Is there Hsync, Vsync waveform
2
3
No
Check IC200 and related circuit.
at Pin 41, 42 of IC 200?
Yes
Does the output signal appear
at Pin 17~20, 22~27 of CN400?
No
Check IC400 and related circuit.
Yes
There are DC 5V at Pin 1, 2
and 3 of CN400?
No
Check PANEL_EN SIGNAL at R236
is High(On:High) and BL_EN signal
at R605(ON:Low) is Low
Yes
Replace LCD Panel.
4-2
http://www.aldiarman.blogspot.com/
4 Troubleshooting
WAVEFORMS
1
2
50V
+3.3V_MAIN
C417
100nF
16V
MO
3
C415
100nF
16V
AVDD_DVI
LVB2P
LVBCKM
LVB1P
LVB2M
G-
2
B+
B-
LVB1M
G+
1
4C-49/SM5H,24MHZ,16PF
C423
100nF
16V
4-3
XREF
VSYNC0
GND
X400
XREF
1
2
3
4
5
6
7
8
9
10
11
C418
18pF
XREF
SCALER_RESET
24.0MHz
NULL
MO
AD0
AD3
GND
VDDP
XREF
C416
18pF
50V
NULL
MO
80
79
78
77
76
75
74
73
72
71
70
BYPASS
81
BUSTYPE
82
NC
83
NC
84
NC
85
NC
86
VDDC
87
GND
88
GND
89
VDDP
90
NC
91
NC
92
AD0
93
AD3
94
HWRESET
95
XIN
96
XOUT
97
AVDD_MPLL
98
GND
99
HSYNC0
100
+3.3V_MAIN
C414
100nF
16V
MO
LVB0P
C404
100nF
16V
RGND
C406
100nF
16V
R+
C405
100nF
16V
GND
LVB0M
C403
100nF
16V
16V
100nF
C402
3
http://www.aldiarman.blogspot.com/
4 Troubleshooting
4-3 No Video (DIGITAL)
Check signal cable connection and
power.
1
X400 oscillate properly?
No
Replace or check related circuit.
Yes
Is there R, G, B input at
4
5
6
No
Check input part.
R110, R112, R114, R111,
R113 and R115?
Yes
Is there waveform
7
No
Check input part.
at R11, R117?
Yes
Does the output signal appear
at Pin 17~20, 22~27 of
CN400?
No
Check IC400 and related circuit.
Yes
There are DC 5V at Pin 1, 2
and 3 of CN400?
No
Check the panel EN signal at R222
and BLEL signal at R603.
Yes
Replace LCD Panel.
4-4
http://www.aldiarman.blogspot.com/
4 Troubleshooting
WAVEFORMS
1
2
3
4
5
6
7
4-5
3
C
2
D109
R125
1K
1/16W
6
C4
MMBD4148SE
3
1
C1
2
A1
3
C
2
1
A
B
3
C
2
D105
5
B
XREF
XREF
XREF
1
A
B
SDA_DDC_D
CHK_DVI
SCL_DDC_D
3
C
2
D103
C2
1
A
MMBD4148SE
4
3
C
2
1
A
3
C
2
R116
R117
R118
R119
R120
R121
R122
R123
B
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
B
3
C
2
D107
ZD102
MMQA5V6T3
RXC
RXC+
RX0+
RX0-
RX1+
RX1-
RX2+
RX2-
VSYNC_IN_A
HSYNC_IN_A
22ohm
22ohm
22ohm
22ohm
22ohm
22ohm
22ohm
22ohm
1
A
XREF
XREF
XREF
XREF
XREF
XREF
XREF
XREF
XREF
XREF
1
A
B
3
C
2
XREF
XREF
XREF
XREF
XREF
XREF
XREF
XREF
D113
MMBD4148SE
A2
B
RX2RX1RX0RX2+
RX1+
RX0+
RXC+
RXC-
MAIN
C3
1
A
C108
100nF
16V
B
330nF
16V
C124
http://www.aldiarman.blogspot.com/
4 Troubleshooting
4 5 6 7
D114
MMBD4148SE
D100
MMBD4148SE
MMBD4148SE
+5V_DDC_D
D106
MMBD4148SE
+5V_DDC_D
UDZS5.6B-T
ZD1
2 B
4-6
http://www.aldiarman.blogspot.com/
5 Exploded View & Parts List
5-1 LS19HAB
T0003
M0215
M0006
M0014
M0107
M0112
M0174
M0113
M0006
T0022
M0013
M0145
M0952
M0045
CIS
5-1
http://www.aldiarman.blogspot.com/
5 Exploded View & Parts List
Location
Code.No
Item & Specification
T0003
BN96-02385B
ASSY COVER P-FRONT;HA19BS,TCO03,ABS HB,G
1
M0112
BN63-01978B
COVER-FRONT;HA19BS,ABS,T2.5,407.6,335,HB
1
S.N.A
T0022
BN64-00377B
KNOB CONTROL;HA17TS,PC CLEAR,T2.1,9,112,
1
S.N.A
M0145
BN96-02474C
ASSY BOARD P-FUNCTION;HAYDN,YWP-VD-05-05
1
M0215
BN07-00203A
LCD-PANEL;M190EN04,GY,6BIT FRC,396*324*1
1
M0006
BN96-01951C
ASSY SHIELD P-COVER;BI19BS,SECC,T0.8,DUA
1
S.N.A
M0107
BN63-01780C
SHIELD-COVER;BI19BS,SECC,T1.0,CHANGE COR
1
S.N.A
M0014
BN94-00735B
ASSY PCB MAIN-ATZ;LS19HAB*,W/W,AU
1
M0174
BN44-00124C
IP BOARD;IP-35135B (H),BI17VS,3.0 ~4.0mA
1
CIS
BN63-01781A
SHIELD-LAMP;BI19BS,SPTE,T0.3
1
M0013
BN96-02386D
ASSY COVER P-REAR;HA19BS,HISP HB,BK24,HA
1
M0113
BN61-01581A
BRACKET-VESA;BI17/19BS,SECC,T1.0
2
S.N.A
M0006
BN63-01979B
COVER-REAR;HA19BS,HIPS,T2.5,407.6,335,HB
1
S.N.A
M0952
BN63-02075A
COVER-DUCT;HA17BS,HIPS,T1.5,13.5,13.5,HB
4
S.N.A
M0045
BN96-02242B
ASSY STAND P-SET;HA19TS,HIPS HB,GR70,SIL
1
5-2
Q'ty
SA/SNA
S.N.A
Remark
http://www.aldiarman.blogspot.com/
5 Exploded View & Parts List
5-2 LS19HAT
M0112
M0014
M0107
M0174
T0022
T0145
T0003
M0215
M0006
M0006
CIS
M0013
M0045
5-3
http://www.aldiarman.blogspot.com/
5 Exploded View & Parts List
Location
Code.No
Item & Specification
T0003
BN96-02239B
ASSY COVER P-FRONT;HA19TS,ABS HB,GR70,SI
1
M0112
BN63-01967B
COVER-FRONT;HA19TS,ABS,T1.5,403.2,331.9,
1
S.N.A
T0022
BN64-00377B
KNOB CONTROL;HA17TS,PC CLEAR,T2.1,9,112,
1
S.N.A
M0145
BN96-02474C
ASSY BOARD P-FUNCTION;HAYDN,YWP-VD-05-05
1
M0215
BN07-00223A
LCD-PANEL;LTM190E4-L21,Haydn,8BIT,396*32
1
M0006
BN96-02241B
ASSY SHIELD P-COVER;HA19TS,SECC T0.8,MEC
1
S.N.A
M0107
BN63-01974B
SHIELD-COVER;HA19TS,SECC,T0.8,398,222,M/
1
S.N.A
M0014
BN94-00735E
ASSY PCB MAIN-SPZ;LS19HATT*,W/W,M/SWICH(
1
M0174
BN44-00123B
IP BOARD;SSIP-1719-HD-A,HAYDN17,3.0 ~5.0
1
CIS
BN63-01781A
SHIELD-LAMP;BI19BS,SPTE,T0.3
1
M0013
BN96-02240A
ASSY COVER P-REAR;HA19TS,HIPS HB,BK24,DU
1
M0006
BN63-01968A
COVER-REAR;HA19TS,HIPS,T2.0,403.2,331.9,
1
M0045
BN96-02242B
ASSY STAND P-SET;HA19TS,HIPS HB,GR70,SIL
1
5-4
Q'ty
SA/SNA
S.N.A
S.N.A
Remark
http://www.aldiarman.blogspot.com/
6 Electrical Parts List
6-1 LS19HATBBV/XAA
Level
Loc. No.
0
Code No.
Description & Specification
EA
LS19HATBBV/XAA
940T,SGT4/S19B0-LHA,19,LCD-MO,UNITED STA
0
SA/SNA
0.1
..2
...3
...3
M0002
M0013
M0006
BN90-00756E
BN96-02240A
BN63-01968A
BN73-00096A
ASSY COVER REAR;LS19HATTSQ/EDC
ASSY COVER P-REAR;HA19TS,HIPS HB,BK24,DU
COVER-REAR;HA19TS,HIPS,T2.0,403.2,331.9,
RUBBER-PANEL;BI19BS,RUBBER,T1.0,50~60,NT
1
1
1
3
S.N.A
0.1
..2
...3
...3
...3
....4
....4
....4
....4
....4
....4
....4
....4
M0001
T0003
M0112
T0022
M0145
C/F
C/F
C/F
CN906
C/F
M2893
T0077
C/F
BN90-00776P
BN96-02239A
BN63-01967A
BN64-00377A
BN96-02474C
0601-001896
2007-000081
2007-000123
3711-005935
BN34-00001A
BN39-00688A
BN41-00633A
BN61-01846A
ASSY COVER FRONT;LS19HATBBV/XAA
ASSY COVER P-FRONT;HA19TS,ABS HB,BK24,D/
COVER-FRONT;HA19TS,ABS,T1.5,403.2,331.9,
KNOB CONTROL;HA17TS,PC CLEAR+SMOG,T2.1,9
ASSY BOARD P-FUNCTION;HAYDN,YWP-VD-05-05
LED;SMD,BLUE,1.6x0.8x0.4mm,470,1.6x0.8x0
R-CHIP;2.7Kohm,5%,1/10W,TP,1608
R-CHIP;1.5Kohm,5%,1/10W,TP,1608
CONNECTOR-HEADER;BOX,4P,1R,1mm,SMD-A,AU,
SWITCH-DOME SHEET;HYADN_FUNCTION F/K,DOM
LEAD CONNECTOR;HAYDN,UL1571#30,4P,450mm,
PCB MAIN;HAYDN,FR4,2L,MP1.0,0.6T,105*8,1
GUIDE-CONTROL;HA17T,ABS HB,T1.1,9,112,IV
1
1
1
1
1
1
2
2
1
1
1
1
1
0.1
..2
M0216
M0045
BN90-00782D
BN96-02652A
ASSY STAND;LS19HATBBV/XAA
ASSY STAND P-SET;HA19TS,HIPS HB,BK24,New
1
1
S.N.A
0.1
..2
T0852
M0215
BN91-00841U
BN07-00223A
ASSY LCD-SPZ;LS19HAT*
LCD-PANEL;LTM190E4-L21,Haydn,8BIT,396*32
1
1
S.N.A
0.1
..2
..2
M0112
CIS
CIS
BN91-00866S
BN63-01781A
0203-001774
ASSY SHIELD;LS19HAT*
SHIELD-LAMP;BI19BS,SPTE,T0.3
TAPE-CONDUCTIVE;DK-100-60-70,AL-TAPE,T0.
1
1
1
S.N.A
S.N.A
S.N.A
0.1
M0019
BN92-00962Q
ASSY LABEL;MJ19BS*,ADC
1
S.N.A
0.1
..2
...3
...3
..2
M0003
T0129
M0103
M0102
BOX
BN92-01540Z
BH75-10529C
BN72-60001A
BN72-60002C
BN69-01107A
ASSY BOX;LS19HATBBV/XAA
UNIT-HANDLE/PACKING;S/M170MP,PE-LD,PE-HD
LEVER-TOP;LSD210TL,PE-LD,WHITE,TFT_LCD
LEVER-BOTTOM;S/M170MP,PE-HD,BLUE
BOX-01,SET;S/M940T(HA19TS),SW4,A,YEL,A1,
1
1
1
1
1.02
S.N.A
S.N.A
S.N.A
S.N.A
0.1
..2
..2
..2
..2
..2
M0113
T0376
T0524
T0376
P/M
M0081
BN92-01543E
6902-000061
6902-000111
6902-000379
6902-000604
6902-000609
ASSY P/MATERIAL;LS19HATBBV/XAA
BAG AIR;LDPE,T0.2,L1000,W500,TRP,,,
BAG PE;HDPE,T0.015,L800,W650,TRP,28,4,PE
BAG AIR;LDPE,T0.2,W1000,L1800,TRP,-,-BAG WRAPPING;LDPE,T0.02,W500,L10000,TRP,
BAG ROLL;LDPE,T0.05,W2400,L1000,TRP,-,-
1
0.01
1
0.002
1.51
0.1
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
0.1
..2
..2
..2
...3
...3
...3
...3
...3
...3
...3
...3
....4
....4
M0045
M0114
M0125
M0045
T0268
T0524
MP1.0
ACCESSORY
ACCESSORY
ACCESSORY
ACCESSORY
M0215
M0808
IB
BN92-01555W
BN39-00244B
BN39-00246F
BN96-02329Q
3903-000085
6902-000110
AA68-40065B
BH68-00261F
BH68-00344C
BN68-00832C
BN68-00832D
BN96-02495G
BH68-00376L
BN59-00486G
ASSY ACCESSORY;LS17HATBBV/XAA
CBF SIGNAL;MO15PS,15P/15P,20276-N,1830MM
CBF SIGNAL-DVI(D);1703FP,24P/24P,20276-D
ASSY ACCESSORY;LS17HAAKB/XAA,U.S
CBF-POWER CORD;DT,US,BP3/YES,I(IEC C13/C
BAG PE;LDPE,T0.05,W250,L400,TRP,28,2
CARD-01,REGISTRATION;,SEA,A5,ENG,A/P220,
CARD WARRANTY-03;SyncMaster14-1,ADC,MOJO
CARD WARRANTY-01;SECA W'TY & CRM CARD,SE
MANUAL-REGISTRATION CARD;SECA all,SAMSUN
MANUAL-REGISTRATION CARD;SECA all,SAMSUN
ASSY MANUAL P-IB+QSG;LS19HAA/940N,SyncMa
MANUAL-04;LCDQUICK SETUP GUIDE,SYNCMASTE
S/W DRIVER-01,IB;LS19HAA/940N,W/W,SyncMa
1
1
1
1
1
1
1
1
1
1
1
1
1
1
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
6-1
http://www.aldiarman.blogspot.com/
6 Electrical Parts List
Level
0.1
..2
...3
...3
..2
...3
...3
...3
...3
...3
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
6-2
Loc. No.
M0017
M0006
M0107
M0014
T0245
CN102
CN101
CN400
T0174
CIS5
D100
D101
D102
D103
D104
D105
D106
D107
D109
D111
D112
D113
D114
ZD100
ZD101
ZD103
ZD104
ZD105
ZD107
ZD108
ZD109
ZD110
ZD201
ZD102
ZD106
ZD200
Q100
Q603
Q604
Q409
IC109
IC112
IC112
T0087
T0087
R100
R101
R102
R103
R104
R105
R233
R270
R116
R117
R118
R119
R120
Code No.
BN91-00889Q
BN96-02241B
BN63-01774A
BN63-01974B
BN94-00735E
0202-001366
3701-001173
3701-001219
3711-005884
BN97-00630H
0202-001375
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0401-001056
0403-001411
0403-001411
0403-001411
0403-001411
0403-001411
0403-001411
0403-001411
0403-001411
0403-001411
0403-001411
0406-001061
0406-001061
0406-001061
0501-002080
0501-002080
0501-002080
0505-001957
1003-001814
1103-000129
1103-001023
1203-003695
1203-003696
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000071
2007-000071
2007-000071
2007-000071
2007-000071
Description & Specification
ASSY CHASSIS-SPZ;LS19HAT*,W/W,M/SWICH(O)
ASSY SHIELD P-COVER;HA19TS,SECC T0.8,MEC
SHIELD-INSULATOR;BI17/19BS,PET,T0.35
SHIELD-COVER;HA19TS,SECC,T0.8,398,222,M/
ASSY PCB MAIN-SPZ;LS19HATT*,W/W,M/SWICH(
SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb,
CONNECTOR-DVI;24P,3R,FEMALE,ANGLE,AUF
CONNECTOR-DSUB;15P,3R,FEMALE,ANGLE,AUF
HEADER-BOARD TO BOARD;BOX,30P,2R,2mm,ANG
ASSY SMD;LS19HATT*
SOLDER-CREAM;RMA-20-21L,S63,-,Sn63/Pb36.
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-SWITCHING;MMBD4148SE,100V,200MA,SO
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-ZENER;-,5.49-5.73V,200MW,SOD-323,T
DIODE-TVS;MMQA5V6T3,5.32/5.6/5.88V,24W,S
DIODE-TVS;MMQA5V6T3,5.32/5.6/5.88V,24W,S
DIODE-TVS;MMQA5V6T3,5.32/5.6/5.88V,24W,S
TR-SMALL SIGNAL;2SC2412K,NPN,200mW,SC-59
TR-SMALL SIGNAL;2SC2412K,NPN,200mW,SC-59
TR-SMALL SIGNAL;2SC2412K,NPN,200mW,SC-59
FET-SILICON;NTR2101P,P,-8V,-3.7A,0.052oh
IC-LCD CONTROLLER;SE56AWL,PQFP,100P,23.4
IC-EEPROM;24C02,256x8,SOP,8P,5x4mm,4.5/5
IC-EEPROM;24C08,1Kx8,SOP,8P,5x4mm,2.5/5.
IC-POSI.FIXED REG.;NCP1117ST33T3G,SOT-22
IC-POSI.FIXED REG.;NCP1117DT18T5G,DPAK,3
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;0ohm,5%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
EA
1
1
1
1
1
0.01
1
1
1
1
1.01
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SA/SNA
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
http://www.aldiarman.blogspot.com/
6 Electrical Parts List
Level
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
Loc. No.
R121
R122
R123
R107
R108
R109
R110
R111
R112
R133
R134
R215
R216
R230
R232
R234
R235
R236
R237
R238
R240
R241
R242
R243
R244
R245
R246
R247
R248
R249
R253
R254
R255
R218
R124
R125
R201
R260
R261
R217
R251
R130
R136
R203
R204
R205
R206
R207
R208
R210
R211
R212
R220
R221
R222
R223
R226
R227
R228
R605
Code No.
2007-000071
2007-000071
2007-000071
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000077
2007-000078
2007-000078
2007-000078
2007-000082
2007-000082
2007-000083
2007-000083
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
Description & Specification
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;22ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;100ohm,5%,1/10W,TP,1608
R-CHIP;470ohm,5%,1/10W,TP,1608
R-CHIP;1Kohm,5%,1/10W,TP,1608
R-CHIP;1Kohm,5%,1/10W,TP,1608
R-CHIP;1Kohm,5%,1/10W,TP,1608
R-CHIP;3.3Kohm,5%,1/10W,TP,1608
R-CHIP;3.3Kohm,5%,1/10W,TP,1608
R-CHIP;3Kohm,5%,1/10W,TP,1608
R-CHIP;3Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
EA
SA/SNA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6-3
http://www.aldiarman.blogspot.com/
6 Electrical Parts List
Level
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
6-4
Loc. No.
R131
R135
R214
R252
R400
R401
R603
R604
R606
R607
R610
R128
R129
R602
R106
R403
R132
R113
R114
R115
R126
R127
R608
R609
C416
C418
C210
C109
C106
C208
C209
C120
C121
C122
C111
C124
C127
C100
C101
C102
C103
C104
C105
C107
C108
C113
C207
C400
C402
C403
C404
C405
C406
C407
C408
C409
C410
C411
C412
C413
Code No.
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000092
2007-000092
2007-000102
2007-000821
2007-000821
2007-001002
2007-001164
2007-001164
2007-001164
2007-001164
2007-001164
2007-002899
2007-002899
2203-000041
2203-000041
2203-000189
2203-000236
2203-000257
2203-000257
2203-000257
2203-000903
2203-000903
2203-000903
2203-000998
2203-001630
2203-001630
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
Description & Specification
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;10Kohm,5%,1/10W,TP,1608
R-CHIP;15Kohm,5%,1/10W,TP,1608
R-CHIP;15Kohm,5%,1/10W,TP,1608
R-CHIP;100Kohm,5%,1/10W,TP,1608
R-CHIP;390ohm,1%,1/10W,TP,1608
R-CHIP;390ohm,1%,1/10W,TP,1608
R-CHIP;510ohm,5%,1/10W,TP,1608
R-CHIP;75ohm,1%,1/10W,TP,1608
R-CHIP;75ohm,1%,1/10W,TP,1608
R-CHIP;75ohm,1%,1/10W,TP,1608
R-CHIP;75ohm,1%,1/10W,TP,1608
R-CHIP;75ohm,1%,1/10W,TP,1608
R-CHIP;10ohm,1%,1/10W,TP,1608
R-CHIP;10ohm,1%,1/10W,TP,1608
C-CER,CHIP;0.01nF,0.25pF,50V,C0G,1608
C-CER,CHIP;0.01nF,0.25pF,50V,C0G,1608
C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608
C-CER,CHIP;0.1nF,5%,50V,C0G,1608
C-CER,CHIP;10nF,10%,50V,X7R,1608
C-CER,CHIP;10nF,10%,50V,X7R,1608
C-CER,CHIP;10nF,10%,50V,X7R,1608
C-CER,CHIP;0.0047nF,0.25pF,50V,C0G,1608
C-CER,CHIP;0.0047nF,0.25pF,50V,C0G,1608
C-CER,CHIP;0.0047nF,0.25pF,50V,C0G,1608
C-CER,CHIP;0.047nF,5%,50V,C0G,1608
C-CER,CHIP;330nF,+80-20%,16V,Y5V,1608
C-CER,CHIP;330nF,+80-20%,16V,Y5V,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
EA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SA/SNA
http://www.aldiarman.blogspot.com/
6 Electrical Parts List
Level
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
....4
.....5
....4
....4
...3
...3
...3
..2
..2
..2
..2
..2
Loc. No.
C414
C415
C417
C419
C420
C421
C423
C424
C605
C607
C610
C611
C615
C618
C619
C620
C215
C216
C604
C614
C205
C422
C608
C609
T0052
T0052
X400
T0568
T0568
T0568
CN600
CN200
T0077
M0018
IC520
C401
C612
M0524
M0131
M0131
M0174
M2893
M0081
M0081
M0081
Code No.
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005005
2203-005065
2203-005065
2203-005065
2203-005065
2203-005437
2203-005437
2402-001128
2402-001128
2703-001334
2703-001334
2801-003773
3301-001145
3301-001145
3301-001145
3711-005503
3711-005509
BN41-00631A
BN97-00626L
0903-001402
2402-001129
2402-001129
BP39-00028A
BN63-00533A
BN63-01243A
BN44-00123B
BN39-00663A
6003-000334
6003-000334
6003-001439
Description & Specification
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;100nF,10%,16V,X7R,1608
C-CER,CHIP;1000nF,+80-20%,10V,Y5V,1608
C-CER,CHIP;1000nF,+80-20%,10V,Y5V,1608
C-CER,CHIP;1000nF,+80-20%,10V,Y5V,1608
C-CER,CHIP;1000nF,+80-20%,10V,Y5V,1608
C-CER,CHIP;10000nF,+80-20%,10V,Y5V,3216
C-CER,CHIP;10000nF,+80-20%,10V,Y5V,3216
C-AL,SMD;100UF,20%,16V,WT,TP,6.3X5.7MM
C-AL,SMD;100UF,20%,16V,WT,TP,6.3X5.7MM
INDUCTOR-SMD;1.5uH,10%,2012
INDUCTOR-SMD;1.5uH,10%,2012
CRYSTAL-SMD;12MHZ,30PPM,28-AAN,20PF,50OH
BEAD-SMD;60OHM,4516,6000,TP,70OHM/45MHZ,
BEAD-SMD;60OHM,4516,6000,TP,70OHM/45MHZ,
BEAD-SMD;60OHM,4516,6000,TP,70OHM/45MHZ,
HEADER-BOARD TO CABLE;BOX,9P,1R,2mm,SMDHEADER-BOARD TO CABLE;BOX,4P,1R,1.25mm,S
PCB MAIN;HAYDN,CEM-3,1.0,1.6,110*78*1.6,
ASSY MICOM;LS19HATT*,W/W,AMLCD
IC-MICROCONTROLLER;NT68F632ALG,8Bit,PLCC
C-AL,SMD;47UF,20%,16V,WT,TP,6.3X5.2MM
C-AL,SMD;47UF,20%,16V,WT,TP,6.3X5.2MM
CONNECT WIRE;BI17,19BS,UL1007#26,9P,80mm
GASKET;BESTBUY17",CONDUCTIVE FABRIC,7.5M
GASKET;KD17AS,CONDUCTIVE FABRIC,3mm,13mm
IP BOARD;SSIP-1719-HD-A,HAYDN17,3.0 ~5.0
LEAD CONNECTOR;LS17BIC,UL1571#30,30P,200
SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR
SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR
SCREW-TAPTITE;BH,+,S,M4,L8,ZPC(YEL)
EA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
SA/SNA
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
S.N.A
6-5
0.6W Self-Loss
7-1 Power Tree
SE16/56AL Interface Operation
SE16/56AL Core Operation
Panel Operating Board
http://www.aldiarman.blogspot.com/
7 Block Diagrams
7 Block Diagram
7-1
http://www.aldiarman.blogspot.com/
7 Block Diagrams
SE16AW /
7-2 Main Board Part
7-2
http://www.aldiarman.blogspot.com/
7 Block Diagrams
7-3 IP Board Part (SMPS Part)
7-3
http://www.aldiarman.blogspot.com/
7 Block Diagrams
7-4 IP Board Part (Inverter Part)
7-4
http://www.aldiarman.blogspot.com/
8 Wiring Diagram
8 Wiring Diagram
8 Wiring Diagram
8-1
http://www.aldiarman.blogspot.com/
9 Schematic Diagrams
9 Schematic Diagrams
- This Document can not be used without Samsung’s authorization.
9-1 Schematic Diagrams(15")
2
1
3
4 5 6 7
9-1
http://www.aldiarman.blogspot.com/
9 Schematic Diagrams
9-2 Schematic Diagrams(17", 19")
9-2
http://www.aldiarman.blogspot.com/
9 Schematic Diagrams
1
2
3
5
6
7
4
9-3
http://www.aldiarman.blogspot.com/
10 Operating Instructions and Installation
10 Operating Instructions and Installation
10-1 Front
1. Menu button
Opens the OSD menu. Also use to exit the OSD
menu or return to the previous menu.
2. MagicBright button
MagicBright is a new feature providing optimum
viewing environment depending on the contents of
the image you are watching. Currently six different
modes are available: Custom, Text, Internet,
Game, Sport and Movie. Each mode has its own
pre-configured brightness value. You can easily
select one of six settings by simply pressing
MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our
engineers, the pre-configured values may not be
comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the OSD menu.
2) Text : Normal brightness
For documentations or works involving heavy text.
3) Internet : Medium brightness
For working with a mixture of images such as text
and graphics.
4) Game
For watching motion pictures such as a game.
5) Sport
For watching motion pictures such as a sport.
6) Movie : High brightness
For watching motion pictures such as a DVD or
Video CD.
3. Brightness button
When OSD is not on the screen, push the button
to adjust brightness.
2,3. Adjust buttons
Adjust items in the menu.
10-1
http://www.aldiarman.blogspot.com/
10 Operating Instructions and Installation
4. Enter button / Source button
Activates a highlighted menu item. /
Push the 'SOURCE', then selects the video signal
while the OSD is off. (When the source button is
pressed to change the input mode, a message
appears in the center of the screen displaying the
current mode -- analog or digital input signal.)
Note : If you select the digital mode, you must connect your monitor to the graphic card's port using
the DVI cable.
6. Power button
Use this button for turn the monitor on and off.
7. Power indicator
This light glows green during normal operation,
and blinks green once as the monitor saves your
adjustments.
5. Auto button
Use this button for auto adjustment.
10-2 Rear
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
Connect the power cord for your monitor to the power port on the back of the monitor.
2. DVI port
Connect the DVI cable to the DVI port on the back of your monitor.
3. D-sub 15-pin port
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
4. Power on/off Switch(option)
Use this button for turn the monitor on and off.
5. Kensington Lock
The Kensington lock is a device used to physically fix the system when using it in a public place.
(The locking device has to be purchased separately. )
To get the information on using the Kensington Lock, contact an aurhorized dealer.
10-2
http://www.aldiarman.blogspot.com/
10 Operating Instructions and Installation
10-3 Connecting the monitor
Rear of monitor
Rear of Computer
New Model Macintosh
Old Model Macintosh
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2-1. Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
2-2. Using the DVI (Digital) connector on the video card.
Connect the DVI cable to the DVI port on the back of your monitor.
2-3. Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
2-4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adapter.
3. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
10-3
http://www.aldiarman.blogspot.com/
10 Operating Instructions and Installation
10-4 Monitor Assembly
10-4
http://www.aldiarman.blogspot.com/
10 Operating Instructions and Installation
10-5 Attaching a Base
- This monitor accepts a 75mm x 75mm VESA-compliant mounting interface pad.
A. Monitor
B. Mounting interface pad
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four
screws that came with the arm-type base, wall mount hanger or other base.
10-5
http://www.aldiarman.blogspot.com/
11 Disassembly and Reassembly
11 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the TFT-LCD monitors.
WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling
these components.
11-1 Disassembly (Simple - Stand)
Cautions:
1. Disconnect the monitor from the power source before disassembly.
1. Place monitor face down on cushioned table. Remove 3 screws from the stand.
2. Remove stand and front cover.
11-1
http://www.aldiarman.blogspot.com/
11 Disassembly and Reassembly
3. Lift up the back cover and Use the jig to remove the shield lamp.
4. Disconnect cables.
5. Lift up the shield and disconnect LVDS cable.
11-2
http://www.aldiarman.blogspot.com/
11 Disassembly and Reassembly
6. Lift up the LCD panel.
11-2 Disassembly (HAS-Stand)
1. Place monitor face down on cushioned table. Remove 2 screws from the stand and remove front cover.
11-3
http://www.aldiarman.blogspot.com/
11 Disassembly and Reassembly
2. Lift up the back cover and Use the jig to remove the shield lamp.
3. Disconnect cables.
4. Lift up the shield and disconnect LVDS cable.
11-4
http://www.aldiarman.blogspot.com/
11 Disassembly and Reassembly
5. Lift up the LCD panel.
11-3 Reassembly
Reassembly procedures are in the reverse order of disassembly procedures.
11-5
12 PCB Layout
12 PCB Diagram
12-1
13 Circuit Descriptions
13 Circuit Descriptions
13-1 Overall Block Structure
13-1-1 Power Tree
Panel Operating Board
SE16/56AL Core Operation
SE16/56AL Interface Operation
0.6W Self-Loss
1. When the AD board is in DPMS state:
1.1 The IP has been designed so that it operates with a power consumption of less than 0.6W of.
1.2 The Scaler consumes power up to 27mA
1.3 The power to the panel is switched off
1.4 The MCU consumes power up to 23mA.
--> The total current consumption to the DPMS is less then 60mA
and the total power consumption is 0.6W + 5V*60mA = 0.9W so that the total power consumption is
less than 1W.
2. When the AD board is operating normally:
2.1 The maximum power consumption of the panel lamps is described below (It may vary depending on
the panel manufacturer)
17" : 4*(7.5mA*650mVrms)=4*4.9=19.6W
19: : 4*(7.5mA*720mVrms)=4*5.4=21.6W
2.2 The power consumption of the Panel Control board is as follows: 5V*720mA=3.6W
2.3 The power consumption of the Scaler is as follows: 3.3V*245mA + 1.8V*300mA = 1.35W
2.4 The power consumption of the MCU is as follows: 5V*44mA =0.22W
13-1
13 Circuit Descriptions
13-1-2 Main Board Parts
1. Inverter: A conversion device that converts DC
rated voltage/current to high ones necessary
for the panel lamp.
2. DC/DC(Regulator): General term for DC to DC
converting devices.
The IP board receives 5V and outputs 1.8 or
3.3V that is supplied to the scaler (SE56AWL).
3. Power MosFET: The IP board receives 5V and
outputs a lower voltage in DPMS mode and
supplies the whole 5V for the panel operating
board in normal conditions. In that case, the
switching of Power MosFET is controlled by
Micom.
4. Scaler: Receives the digital TMDS and analog
R,G,B signals and convert them to proper resolutions using up- or down- scaling that are
transferred to the panel in the LDVS formats.
5. Crystal(Oscillator): Use one 24MHz oscillator
externally to supply power to both MCU and
Scaler at the same time.
13-2
6. MCU & EEPROM: I2C is a two-way serial bus of
two lines that supports communications across
the integrated circuits as well as between MCU,
Scaler and EEPROM.
In particular, MCU and Scaler (SE56AWL) use
the DDR direct bus for mutual communications,
which is an effective, speedy system because it
allows 4 additional address/data lines compared to the old serial systems.
7. Function Key: A certain keystroke generates a
certain electrical potential, which is transferred
into ADC input port of the MCU and then converted to a digital value by the A/D converter of
the chip. The digital value (data) is a clue to
which key is entered. In practical, the voltage
levels are set as below.
13 Circuit Descriptions
13-1-3 IP BOARD BLOCK(POWER) Parts
13-1-4 IP BOARD BLOCK( INVERTER ) Parts
IP BO A RD
B LO C K
( IN V ERT ER )
D C Input
nput
+1
13V dc
IN V ERT ER PA RT
POWER
DC INPUT
Lamp
FULL
BRIDGE
CIRCUIT
Lamp
Lamp
Lamp
+5
5V
Vd
dc
A D IM + 3.
.3V
3 dc
BD IM + 4.
.5V dc
ON/OFF
DIM INPUT
INVERTER
CONTROL
IC
DRIVER
IC
FEED BACK
CIRCUIT
PROTECTION
CIRCUIT
C O N T RO L PA RT
13-3
13 Circuit Descriptions
13-1-5 IP BOARD ( inverter ) PROTECTION Parts
BIZET INVERTER CONTROLER FAN7310 have 2-way of the PROTECTION MODE.
1. OVP[Over Voltage Protection] : If the Voltage of the series capacitors C10 & C15 is over the 2.0V, the
Inverter latched-off.[See the Picture1]
2. OLP[Over Load Protection] : If the inverter output harness is opened(No-output current), the base of the
Q1 turns on and chage the C9 ovter 2V and then, the Inverter latchedoff[See the Picture2]
Figure 1.
Figure 2.
13-4
13 Circuit Descriptions
13-2 Trouble Shooting
13-2-1 IP BOARD(Power)
Power On
No
Check fuse
Change FUSE
Yes
3 pin of FDM0565R
Vcc system in normal: HIGH
No
Check the Vcc system
Yes
1 pin of FDM0565R
Check the drain system
Normal: Switching
No
Check the main switching
Yes
Check the
protection system
No
Check the output current
No
Check the
feedback system
Yes
Check others
Harness, Inlet
13-5
13 Circuit Descriptions
13-2-1 IP BOARD(Inverter)
Power On
No
Check the power system
Yes
1 and 2 pins of FDM0565R
Check Protection
Normal:0.6V~0.8V
No
Check the IC drive
Check MOSFET
No
Check the OVP and OLR
circuits
Yes
1 and 2 pins of FDM0565R
Check Protection
Normal:0.6V~0.8V
Yes
Check any dimming
circuit
No
No
Check the output current
Yes
Check others
13-6
Check the feedback
system
13 Circuit Descriptions
13-3 IP BOARD(Power) Schematic Diagrams
13-7
13 Circuit Descriptions
13-4 IP BOARD(Inverter) Schematic Diagrams
13-8
14 Reference Infomation
14 Reference Infomation
14-1 Technical Terms
-TFT-LCD
(Thin film Transistor Liquid Crystal Display)
ADC(Analog to Digital Converter)
This is a circuit that converts from analog signal to
digital signals.
-PLL(Phase Locked Loop)
During progressing ADC, Device makes clock synchronizing HSYNC with Video clock
-Inverter
Device that supply Power to LCD panel lamp. this
device gernerate about 1,500~2,000V.
AC Adapter
Device that converts AC(90V~240V) to DC(+12V or
14V)
SMPS(Switching Mode Power Supply)
Switching Mode Power supply. This design technology is used to step up/down the input power by
switching on/off
-FRC(Frame Rate Controller)
Technology that change image frame quantity displayed on screen for one second.
Actually TFT-LCD panel require 60 pcs of frame for
one second.
so,this technology is needed to convert input image
to 60 pcs regardless input frame quantity.
-Image Scaler
Technology that convert various input resolution to
other resolution.(ex. 640* 480 to 1024*768)
-Auto Configuration(Auto adjustment)
This is an algorithm to adjust monitor to optimum
condition by pushing one key.
-OSD(On Screen Display)
On screen display. customer can control the screen
easily with this.
-Image Lock
This means "Fineness adjustment " in LCD Monitor,
the features are "Fine" and "Coarse"
-FINE
"Fine" adjustment is used to adjust visibility by control phase difference.
-COARSE
This is a adjustment by tuning with Video colck and
PLL clock.
-DVI (Digital Visual Interface)
This provides a high speed digital connection for
visual data types that is display technology independent. this interface is primarily forcused at providing a connection between a computer and
its display device.
-L.V.D.S.(Low Voltage Differential Signaling)
a kind of transmission method for Digital.It can be
used from Main PBA to Panel.
-DVI (Digital Visual Interface)
This provides a high speed digital connection for
visual data types that is display technology independent. this interface is primarily forcused at providing a connection between a computer and its display device.
-T.M.D.S
(Transition minimized Differential Signaling)
a kind of transmission method for Digital.
It can be used from Video card to Main PBA.
-DDC(Display data channel)
It is a communication method between Host
Computer and related equipment.
It can make it Plug and Play between PC and
Monitor.
-EDID
Extended Display Identification Data PC can recognize the monitor information as Product data,
14-1
14 Reference Infomation
Product name,Display mode,Serial number and
Signal source,etc through DDC Line communicating
with PC and Monitor.
-Dot Pitch
The image on a monitor is composed of red, green
and blue dots. The closer the dots, the higher the
resolution. The distance between two dots of the
same color is called the 'Dot Pitch'. Unit: mm
-Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the
user. The frequency of this repetition per second is
called Vertical Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times
per second, this is regarded as 60 Hz.
-Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called
Horizontal Cycle. The inverse number of the
Horizontal Cycle is called Horizontal Frequency.
Unit: kHz
-Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the
top to the bottom in order is called the Non-Interlace
method while showing odd lines and then even lines
in turn is called the Interlace method. The NonInterlace method is used for the majority of monitors
to ensure a clear image. The Interlace method is the
same as that used in TVs.
-Plug & Play
This is a function that provides the best quality
screen for the user by allowing the computer and
the monitor to exchange information automatically.
This monitor follows the international standard
VESA DDC for the Plug & Play function.
-Resolution
The number of horizontal and vertical dots used to
compose the screen image is called 'resolution'.
This number shows the accuracy of the display.
High resolution is good for performing multiple tasks
as more image information can be shown on the
screen.
Example: If the resolution is 1280 x 1024 , this
means the screen is composed of 1280 horizontal
dots (horizontal resolution) and 1024 vertical lines
(vertical resolution).
14-2
14 Reference Infomation
14-2 Pin Assignments
Sync
Type
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15-Pin D-Sub Signal Cable Connector
Separate
Composite
Sync-on-green
Red
Green
Blue
GND
DDC Return (GND)
GND-R
GND-G
GND-B
DDC Power Input (+5V)
Self Raster
GND
Bi-Dr Data (SDA)
H-Sync.
V-Sync.
DDC Clock (SCL)
Red
Green
Blue
GND
DDC Return (GND)
GND-R
GND-G
GND-B
DDC Power Input (+5V)
Self Raster
GND
Bi-Dr Data (SDA)
H/V-Sync.
Not Used
DDC Clock (SCL)
Red
Green + H/V Sync.
Blue
GND
DDC Return (GND)
GND-R
GND-G
GND-B
DDC Power Input (+5V)
Self Raster
GND
Bi-Dr Data (SDA)
Not Used
Not Used
DDC Clock (SCL)
Sync
Type
Pin No.
24P DVI-D
1
Rx2-
13
No Connection
2
Rx2+
14
+5V_M
3
GND
15
Self Raster
4
No Connection
16
+5V_M
5
No Connection
17
Rx0-
6
DDC Clock (SCL)
18
Rx0+
7
DDC Data (SDA)
19
NC
8
NC
20
No Connection
9
Rx1-
21
No Connection
10
Rx1+
22
NC
11
NC
23
RxC+
12
No Connection
24
RxC-
14-3
14 Reference Infomation
14-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard for computergenerated video signals.
Table 2-1 Timing Chart
VESA
IBM
Mode
VGA2/
70 Hz
Timing
VGA3/
60 Hz
640/75 Hz 800/60 Hz 800/75 Hz 1024/60 Hz 1024/75 Hz 1280/60 Hz 1280/75 Hz
720 x 400 640 x 480
640x480
800x600
800x600
1024x768 1024x768 1280x1024 1280x1024
31.469
31.469
37.500
37.879
46.875
48.363
60.023
63.981
79.975
µ
31.777
31.778
26.667
26.400
21.333
20.677
16.660
11.852
12.504
µ
3.813
3.813
2.032
3.200
1.616
2.092
1.219
1.037
1.067
µ
1.589
1.589
3.810
2.200
3.232
2.462
2.235
2.296
1.837
µ
26.058
26.058
20.317
20.000
16.162
15.754
13.003
9.259
9.481
µ
0.318
0.318
0.508
0.000
0.323
0.369
0.203
0.000
0.119
70.087
59.940
75.000
60.317
75.000
60.004
75.029
60.020
75.025
14.268
16.683
13.333
16.579
13.333
16.666
13.328
16.005
13.329
0.064
0.064
0.080
0.106
0.064
0.124
0.050
0.047
0.038
0.858
0.794
0.427
0.607
0.448
0.600
0.466
0.594
0.475
13.155
15.761
12.800
15.840
12.800
15.880
12.795
15.630
12.804
0.191
0.064
0.027
0.0261
0.021
0.062
0.017
0.016
0.013
28.322
26.175
31.500
40.000
49.500
75.000
78.750
108.000
135.000
Negative Negative Negative Positive
Positive Negative
Positive
Positive
Positive
Positive Negative Negative Positive
Positive Negative
Positive
Positive
Positive
Separate Separate Separate Separate Separate Separate Separate Separate Separate
H/V Composite Sync
Separate Sync
Video
Video
C
D
E
Q
R
S
Sync-on-Green
Sync
Sync
B
P
A
O
A : Line time total
B : Horizontal sync width
O : Frame time total
P : Vertical sync width
C : Back porch
D : Active time
Q : Back porch
R : Active time
E : Front porch
14-4
S : Front porch
14 Reference Infomation
14-4 Preset Timing Modes
-If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen
will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED
is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing
Display Mode
Horizontal
Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC,1152 x870
68.681
75.062
100.000
-/-
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+,-/+,-
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.00
+/+
VESA 1280 x 960
60.000
60.000
108.00
+/+
VESA, 1280 x 1024
63.981
60.020
108.00
+/+
VESA, 1280 x 1024
79.976
75.025
135.00
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called
Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an
image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
14-5
14 Reference Infomation
14-5 Panel Description
Maker
VENDOR P/N
PANEL_CODE
PANEL_ABB
STICKER_CODE
SEC
LT140X1-002
BN07-00004A
SA
SEC
LT150XS-L01
BN07-00009A
SB
-
SEC
LT150XS-L01-B
BN07-00022A
SC
-
SEC
LTM150XS-L02
BN07-00005A
SD
-
SEC
LT181E2-132
BN07-00001A
SE
-
SEC
LT150XS-T01
BN07-00010A
SF
-
SEC
LTM181E3-132
BN07-00019A
SG
-
SEC
LT170E2-131
BN07-10001D
SH
-
SEC
LT181E2-131
BN07-10001E
SJ
-
SEC
LTM170E4-L01
BN07-00018A
SK
-
SEC
LTM240W1-L01
BN07-00015A
SL
-
SEC
LTM213U3-L01
BN07-00016A
SM
-
SEC
LTM150XH-L01
BN07-00026A
SN
-
SEC
LTM150XH-L03
BN07-00027A
SP
-
SEC
LTM150XS-L01
BN07-00032A
SQ
DELL(ZPD)
SEC
LTM181E4-L01
BN07-00034A
SR
PVA
SEC
LTM170EH-L01
BN07-00036A
SS
TN
SEC
LTM170E5-L01
BN07-00037A
SU
PVA
SEC
LTM150XH-L11
BN07-00041A
SV
-
SEC
LTM213U4-L01
BN07-00039A
SW
PVA
SEC
LTM150XH-L01(ZPD)
BN07-00045A
SX
ZPD
SEC
LTM150XH-L04
BN07-00046A
SY
New panel with high brightness
SEC
LTM170W1-L01
BN07-00047A
SZ
Panel for TV
SEC
LTM150XH-L06
BN07-00053A
EA
Panel for TV/ High luminance for 450cd _ SONY&EOS Team Panel for TV
SEC
LTM153W1-L01
BN07-00054A
EB
Use NIKE MODEL
SEC
LTM170EH-L05
BN07-00055A
EC
Panel EOS proj. for high brightness of 17" EH-L05
SEC
LTM170E5-L03
BN07-00056A
ED
Dell 1702FP pro. E4. EH mechanical Compatible
SEC
LTM190E1-L01
BN07-00057A
EE
DELL 1900 FP
SEC
LTM181E5-L01
BN07-00061A
EF
18" narrow bezel GH18PS
SEC
LTM150XP-L01
BN07-00065A
EG
AMLCD PVA PANEL
SEC
LTM240W1-L02
BN07-00062A
EH
Panel for 15" Wide TV
SEC
LTM170EU-L01
BN07-00071A
EJ
Slim design, TN
SEC
LTM170E5-L04
BN07-00072A
EK
E5-L04 6 bits FRC... for IBM
SEC
LTA220W1-L01
BN07-00074A
EL
Panel for 22" TV
SEC
LTM170E6-L02
BN07-00075A
EM
AMLCD Narrow & slim design 17" PVA mode
SEC
LTM170W1-L01
BN07-00082A
EN
LTM170W1-L01 ZPD panel
SEC
LTM170EH-L01
BN07-00080A
EP
LTM170EH-L01 ZPD panel
SEC
LTM170E5-L01
BN07-00081A
EQ
LTM170E5-L01 ZPD panel
SEC
LTM170EH-L05
BN07-00083A
ER
LTM170EH-L05 ZPD panel
SEC
LTM170E5-L03
BN07-00084A
ES
LTM170E5-L03 ZPD panel
SEC
LTM170EU-L01
BN07-00085A
ET
LTM170EU-L01 ZPD panel
SEC
LTM170E5-L04
BN07-00086A
EU
LTM170E5-L04 ZPD panel
SEC
LTM170E6-L02
BN07-00087A
EV
LTM170E6-L02 ZPD panel
SEC
LTM150XH-L06
BN07-00091A
EW
Color coordinates change for LCD TV
SEC
LTM153W1-L01
BN07-00092A
EX
AMLCD WIDE 15",9/10
SEC
LTM170W1-L01
BN07-00100A
EY
Color Coordinates change code management
SEC
LTM170EH-L05
BN07-00097A
EZ
LTM170E5-L05 Color Coordinates Change Panel Code
SEC
LTA400W1-L01
BN07-00109A
S1
PANEL of AMLCD 40" TV
SEC
LTM153W1-L01
BN07-00110A
S2
Color coordinates change 0.280/0.290, 10000k & ZPD Panel
SEC
LTM150XH-L06
BN07-00111A
S3
Color coordinates change 0.280/0.290, 10000k & ZPD Panel
14-6
BN68-00239H
Remarks
-
14 Reference Infomation
Maker
VENDOR P/N
PANEL_CODE
PANEL_ABB
STICKER_CODE
Remarks
SEC
LTM170W1-L01
BN07-00112A
S4
Color coordinates change 0.280/0.290, 10000k & ZPD Panel
SEC
LTM170EH-L05
BN07-00113A
S5
Color coordinates change 0.280/0.290, 10000k & ZPD Panel
SEC
LTM220W1-L01
BN07-00114A
S6
ZPD Panel for AMLCD 22" TV
SEC
LTM150XH-L06
BN07-00117A
S7
ZPD Panel code
SEC
LTM153W1-L01
BN07-00118A
S8
ZPD Panel code
SEC
LTM170WP-L01
BN07-00119A
S9
PVA Panel for NIKE
SEC
LTM213U4-L01
BN07-00039A
E1
21.3" NARROW
SEC
LTA260W1-L01
BN07-00121A
E2
VENUS
SEC
LTA220W1-L01
BN07-00074B
E3
"Panel B-level panel code for 22"" TV Panel "
SEC
LTA320W1-L01
BN07-00108A
E4
"Panel for AMLCD 32"" TV"
SEC
LTM213U4-L01
BN07-00124A
E5
NARROW BEZEL 21 " PANEL
SEC
LTM170E6-L04
BN07-00129A
E6
"HIGHLAND 17"" LOW PANEL (Panel only for TCO03)"
SEC
LTM190E1-L01
BN07-00088A
E7
LTM190E1-L01 ZPD panel
SEC
M150X4-L06
BN07-00137A
E8
15" Narrow & Slim panel
SEC
LTA170V1
BN07-00139A
E9
"17"" Panel for Muse 4:3 VGA TV"
SEC
LTM190E1-L02
BN07-00128A
E10
"New Panel from AMLCDl, Specification : 6bit Driver IC"
SEC
LTM170EX-L01
BN07-00143A
E11
"Development new Panel from AMLCD"
SEC
LTM170E8-L01
BN07-00144A
E12
"Development new Panel from AMLCD"
SEC
LTM170E6-L04
BN07-00129B
E13
"ZPD panel for AMLCD (Panel only for TCO03)"
SEC
LTA320W1-L02
BN07-00108B
E14
"Creat B-level Panel code for AMLCD 32"" TV"
SEC
LTM190E1-L03
BN07-00151A
E15
"Development new 19"" Panel form AMLCD (Panel only for TCO03)"
SEC
LTM240W1-L03
BN07-00134A
E16
"AMLCD 24"" panel development"
SEC
LTM190E1-L02
BN07-00128B
E17
"New Panel from AMLCD, Specification : 6bit Driver IC(ZPD)"
SEC
LTM190E4-L01
BN07-00145A
E18
"AMLCD 24"" new panel development"
SEC
LTM170E8-L01
BN07-00158A
E19
"ZPD code derivation"
SEC
LTM170EX-L01
BN07-00159A
E20
"ZPD code derivation"
SEC
LTM190E1-L03
BN07-00151B
E21
"Creat new panel code for AMLCD 19"" (Panel only for TCO03)"
SEC
LTA460H1-L01
BN07-00157A
E22
"creat panel code for AMLCD 46"" TV "
SEC
LTM170EU-L11
BN07-00160A
E23
"creat new panel code for AMLCD 17"" (Panel only for TCO03)"
SEC
LTM240W1-L03
BN07-00134B
E24
"24"" panel ZPD code derivation"
SEC
LTM190E4-L01
BN07-00145B
E25
"AMLCD 19"" ZPD Panel code derivation"
SEC
LTM240W1-L03
BN07-00134B
E26
"24"" panel ZPD code derivation"
SEC
LTM150XO-L01
BN07-00164A
E27
"AMLCD 15"" XO-L01 new panel development"
SEC
LTM150XO-L01
BN07-00164B
E28
"AMLCD 15"" XO-L01 ZPD code derivation"
SEC
LTM170EU-L11
BN07-00160B
E29
"AMLCD 17"" NEW panel code derivation"
SEC
LTA320W2-L01
BN07-00172A
SPZ
AMLCD 32" NEW panel
SEC
LTM213U4-L01
BN07-00124B
SPZ
21.3" Narrow PANEL ZPD Panel derivation
SEC
LTM170EU-L11
BN07-00189A
STH
AMLCD EU-L11 Pb free panel code derivation
SEC
LTM170EU-L11
BN07-00189B
STZ
AMLCD EU-L11 Pb free panel ZPD code derivation
SEC
LTM240W1-L04
BN07-00188A
SPH
24" A-DCC new panel development
SEC
LTM240W1-L04
BN07-00188B
SPZ
24" A-DCC panel ZPD code derivation
SEC
LTM190EX-L01
BN07-00191A
STH
AMLCD 19" TN new Panel
SEC
LTM190EX-L02
BN07-00191B
STZ
AMLCD 19" TN new Panel ZPD derivation
SEC
LTA230W1-L02
BN07-00184A
SPZ
AMLCD 23" 16:9 new Panel
SEC
LTA260W2-L01
BN07-00185A
SPZ
AMLCD 26" 16:9 new Panel
SEC
LTM240M1-L01
BN07-00195A
SPH
24" panel with high brightness deveiopment
SEC
LTA400W2-L01
BN07-00186A
SPZ
AMLCD 40" 16:9 new Panel
SEC
LTM150XO-L01
BN07-00197A
STH
AMLCD 15" XO-L01 Pb free panel code
SEC
LTM150XO-L01
BN07-00197B
STZ
AMLCD 15" XO-L01 Pb free panel ZPD code
SEC
LTM170EU-L21
BN07-00202A
STZ
AMLCD EU-L21 ZPD new code derivation
14-7
14 Reference Infomation
Maker
VENDOR P/N
PANEL_CODE
PANEL_ABB
STICKER_CODE
Remarks
SEC
LTA460W2-L03
BN07-00187A
SPZ
BEETOVEN 46"ZPD new panel
SEC
LTM240M1-L01
BN07-00195B
SPZ
24" igh brightness panel ZPD code derivation
SEC
M170EX-L21
BN07-00206A
STZ
AMLCD LTM170EX-L21 ZPD new code derivation
SEC
LTA460H3-L01
BN07-00200A
SPZ
AMLCD 46" LED BLU panel
SEC
LTM170EU-L15
BN07-00214A
STZ
AMLCD EU-L15 TV high brightness ZPD new code derivation
SEC
LTM170E8-L21
BN07-00218A
SPZ
AMLCD LTM170E8-L21 PVA ZPD new code derivation
SEC
LTM190EX-L21
BN07-00222A
STZ
DISPLAY LCD
SEC
LTM201U1-L01
BN07-00190B
SPZ
AMLCD 20.1" Normal panel ZPD code derivation
SEC
LTM190E4-L21
BN07-00223A
SPZ
HAYDN 17" PZD code PANEL derivation
SEC
LTA570H1-L01
BN07-00196A
SPZ
AMLCD 57" new panel development
SEC
LTM150XO-L21
BN07-00229A
STZ
AMLCD 15" XO-L21 8ms panel code
SEC
LTA260W2-L11
BN07-00239A
SPZ
AMLCD 26" 16:9 7Line new Panel
SEC
LTA400WS-LH1
BN07-00245A
SPZ
AMLCD 40" 16:9 SPVA 90% new Panel
SEC
LTM213U6-L01
BN07-00231A
SPZ
AMLCD 21.3" PVA new Panel Code
SEC
LTA320WS-LH2
BN07-00244A
SPZ
AMLCD 32" 16:9 SPVA 90% new Panel
SEC
LTA400WS-LH1
BN07-00245A
SPZ
AMLCD 40" 16:9 SPVA 90% new Panel
SEC
LTM190M2-L01
BN07-00227A
STZ
AMLCD 19" TN Wide new Panel Code
SEC
LTM201UX-L01
BN07-00249A
STZ
AMLCD 20.1" TN new Panel Code
CPT
CLAA150XG09
BN07-00141A
PA
"CPT 15"" Monitor new panel development"
CPT
CLAA170EA02
BN07-00148A
PB
"17"" CPT NEW development panel"
CPT
CLAA170EA02
BN07-00148B
PC
"17"" CPT ZPD panel code derivation"
CPT
CLAA150XG09
BN07-00141B
PTZ
"CPT 15"" panel ZPD code derivation (GOYA-PJT)"
CPT
CLAA150XP01
BN07-00173A
PTH
CPT 15" PSWG code derivation
CPT
CLAA150XP01
BN07-00173B
PTZ
CPT 15" PSWG panel ZPD code
CPT
CLAA170EA07
BN07-00174A
PTH
"CPT 17"" PSWG panel code derivation
CPT
CLAA170EA07
BN07-00174B
PTZ
CPT 17"""" PSWG type new Panel code"""
CPT
CLAA170EA07
BN07-00174B
PTZ
CPT 17" PSWG type new Panel code
CPT
CLAA170EA07Q
BN07-00220A
PTZ
CPT 17" PSWG R/T 8msec code derivation
CPT
CLAA170EA07Q
BN07-00220B
PTH
CPT 17" PSWG R/T 8msec HPD code derivation
CPT
CLAA150XP01F
BN07-00236A
PTZ
CPT 15" PSWG panel ZPD & Lead free code derivation
TOSHIBA
LTM15C419(A)
BN07-00002A
TA
-
TOSHIBA
LTM15C423(B)
BN07-00006A
TB
-
TOSHIBA
LTM18C161
BN07-00008A
TC
-
TOSHIBA
LTM15C443
BN07-00031A
TD
-
TOSHIBA
LTM15C458
BN07-00043A
TE
-
TOSHIBA
LTM15C458S
BN07-00077A
TF
"TSB 15"" high brightness Panel"
TOSHIBA
LTM15C458
BN07-00078A
TG
Toshiba ZPD panel
TOSHIBA
LTM15C458S
BN07-00099A
TH
TSB LTM15C458S ( ZPD )
HANNSTAR
HSD150MX41A(A)
BN07-00020A
NA
"TTL type"
HANNSTAR
HSD150MX12
BN07-00030A
NB
"TTL type"
HANNSTAR
HSD170ME13
BN07-00180A
NTH
Hannstar 17" TN new panel development
HANNSTAR
HSD170ME13
BN07-00180B
NTZ
Hannstar 17" TN new panel development ZPD code derivation
HANNSTAR
HSD190ME12
BN07-00210A
NTZ
Hannstar 19" TN new panel development
HANNSTAR
HSD150MX17-A
BN07-00226A
NTZ
Hannstar 15" slim panel ZPD code derivation
TORISAN
TM150XG-22L03(A)
BN07-00021A
RA
-
TORISAN
TM150XG-26L06
BN07-00042A
RB
-
14-8
14 Reference Infomation
Maker
VENDOR P/N
PANEL_CODE
PANEL_ABB
STICKER_CODE
Remarks
TORISAN
TM181SX-76N01
BN07-00048A
RC
-
TORISAN
TM150XG-26L06
BN07-00059A
RD
15" XGA TN MODE(ZPD)
TORISAN
TM290WX-71N31
BN07-00063A
RE
"RS24NS (TORISAN 29"" NEW PANEL)"
TORISAN
TM396WX-71N31
BN07-00064A
RF
"RS24NS (TORISAN 40"" NEW PANEL)"
TORISAN
TM150XG-26L09
BN07-00073A
RG
"Panel for 15"" TV"
TORISAN
TM150XG-26L10
BN07-00089A
RH
"L10(change except D/IC) ZPD"
TORISAN
TM150XG-26L10
BN07-00090A
RJ
L10 NORMAL
TORISAN
TM190SX-70N01
BN07-00098A
RK
Torisan 19" Panel
TORISAN
TM181SX-76N01
BN07-00106A
RL
ZPD Panel code
TORISAN
TM190SX-70N01
BN07-00107A
RM
ZPD Panel code
TORISAN
TM290WX-71N31
BN07-00115A
RN
"Color Coordinates change panel for TORISAN 29"" TV"
TORISAN
TM396WX-71N31
BN07-00116A
RP,Q
"Color Coordinates change panel for TORISAN 40"" TV"
TORISAN
TM22OWX-71N31
BN07-00125A
RR
"Development TORISAN 22"" TV PANEL (ZPD)"
TORISAN
TM22OWX-71N31
BN07-00127A
RS
"Development TORISAN 22"" TV PANEL (HPD)"
TORISAN
TM396WX-71N32A
BN07-00150A
RT
120V inverter Exclusive panel
TORISAN
TM190SX-70N02
BN07-00154A
RMH
Torisan 6bit panel code Derivation
TORISAN
TM190SX-70N02
BN07-00154B
RMZ
Torisan 6bit panel code Derivation
TORISAN
TM150XG-A01
BN07-00162A
RTH
Torisan 15" Narrow & Slim panel development
TORISAN
TM150XG-A01
BN07-00162B
RTZ
Torisan 15" N&S panel ZPD code Derivation
SHARP
LQ181E1DG11(A)
BN07-10001C
PA
-
SHARP
LQ150X1LW71
BN07-00067A
PB
SHARP 15" PVA PANEL
SHARP
LQ370T3LZ41
BN07-00216A
FAZ
Rome2
HITACHI
TX38D12VC0CAA(A)
BN07-00003A
HA
-
HITACHI
TX43DVCOCAB
BN07-00060A
HB
17" SXGA PVA MODE
HITACHI
TX43D15VC0CAB
BN07-00101A
HC
ZPD Panel
HITACHI
TX51D11VC0CAB
BN07-00122A
HD
20.1" NARROW
HITACHI
TX54D11VC0CAB
BN07-00123A
HE
21.3" NARROW
HITACHI
TX80D12VC0CAB
BN07-00169A
HIZ
"Development new panel for Hitachi 32"" TV (ZPD)"
HITACHI
TX54D11VC0CAB
BN07-00123B
HIZ
Hitachi 21.3"ZPD panel
IBM
ITSX94S
BN07-00017A
IA
-
UNIPAC
UM170E0
BN07-00028A
UA
Loaded by cisdba
HYUNDAI
HT15X13
BN07-00035A
DA
-
HYUNDAI
HT17E11-200
BN07-00049A
DB
TN MODE
HYUNDAI
HT17E11-300
BN07-00093A
DC
HT17E11-300 ZPD panel
HYUNDAI
HT17E11-400
BN07-00094A
DD
HT17E11-400 normal panel
HYUNDAI
HT17E11-400
BN07-00095A
DE
HT17E11-400 ZPD panel code
HYUNDAI
HT17E12
BN07-00096A
DF
HT17E12 ( Narow & slim Design )
HYUNDAI
HT17E12
BN07-00105A
DG
ZPD Panel code
HYUNDAI
HT15X15-D00
BN07-00146A
DH
"Development for Ares 15"" Hydis TV"
HYUNDAI
HT15X15-D01
BN07-00146B
DJ
"Derivation panel HPD for Ares 15"" Hydis TV "
HYUNDAI
HT17E13-100
BN07-00167A
DTH
"PINEHURST-2(IBM) PJT 17"" HYDIS PANEL Derivation"
HYUNDAI
HT17E13-100
BN07-00167B
DTZ
"PINEHURST-2(IBM) Hydis 17"" ZPD code Derivation"
HYUNDA
HT170EX1-100
BN07-00240A
DTZ
17" EX compatible Hydis Slim panel development
ACER
L170E3
BN07-00044A
AA
TN(ADT)
ACER
M170EN05
BN07-00076A
AB
AU 17" Panel ( Narrow & slim design )
14-9
14 Reference Infomation
Maker
VENDOR P/N
PANEL_CODE
PANEL_ABB
STICKER_CODE
Remarks
ACER
M170EN05
BN07-00102A
AC
ZPD Panel code
ACER
M190EN02
BN07-00170A
AMH
"AU Monitor 19"" new panel development (P19-1S)"
ACER
M190EN02
BN07-00170B
AMZ
"AU 19"" ZPD code derivation (ZPD)"
ACER
M170EN06
BN07-00171A
ATH
"AU Monitor 17"" New panel development "
ACER
T260XW01
BN07-00163A
AMZ
"AU 26"" new panel development (NF26EO)"
ACER
A201SN01
BN07-00177A
ATZ
"AU TV panel 20.1"" TN SVGA new panel development"
ACER
M170EN06
BN07-00171B
ATZ
AU Monitor 17" ZPD code derivation
ACER
T315XW01
BN07-00194A
AMZ
AU 32" new
ACER
M170EG01
BN07-00192A
ATH
AU TN PSWG type new Panel code
ACER
M170EG01
BN07-00192B
ATZ
AU TN PSWG type NEW panel code derivation
ACER
M190EN04
BN07-00203A
ATH
AU Monitor 19" ZPD new Panel code
ACER
T260XW02
BN07-00208A
AMZ
AUO 26" ZPD panel
ACER
M170EG01 V8
BN07-00221A
ATZ
AU TN PSWG type new Panel (8msec) ZPD code derivation
ACER
T260XW02
BN07-00233A
AMZ
AUO 26" Panel new (Cosmetic spec down grade)
ACER
T315XW01
BN07-00234A
AMZ
AUO 32" Grade new (Cosmetic spec down grade)
ACER
M190EN03
BN07-00224A
AMZ
AU Monitor 19" MVA new code derivation
ACER
T315XW01
BN07-00237A
AMZ
LCD TV VE project new
ACER
T315XW01
BN07-00238A
AMZ
LCD TV VE project new
ACER
M201UN02 V3
BN07-00168A
AMZ
ACER
M190EN04 V7
BN07-00248A
ATZ
AU Monitor 19" TN Glare ZPD new code derivation
CHIMEI
M170E3-LO1
BN07-00050A
CA
TN PANEL
CHIMEI
M150X3-L01
BN07-00051A
CB
COMPATIBLE
CHIMEI
M170E4-L01
BN07-00052A
CC
MVA PANEL
CHIMEI
M150X2-L01
BN07-00066A
CD
CHIME 15"I PVA PANEL
CHIMEI
M150X3-L01
BN07-00079A
CE
Chimei ZPD panel
CHIMEI
M170E3-L01
BN07-00103A
CF
ZPD Panel code
CHIMEI
M170E4-L01
BN07-00104A
CG
ZPD Panel code
CHIMEI
V296W1-L01
BN07-00120A
CH
MVA
CHIMEI
M170E6-L02
BN07-00126A
CJ
HIGHLAND 17" LOW PANEL
CHIMEI
M190E2-L01
BN07-00131A
CK
GH19AS,BS CHIMEI PANEL
CHIMEI
M150X4-L06
BN07-00137A
CL
15" Narrow & Slim panel
CHIMEI
M170E6-L01
BN07-00133A
CM
"2003-03-11 vendor change"
CHIMEI
M170E6-L01
BN07-00133B
CN
ZPD derivation panel
CHIMEI
V201V1-T01
BN07-00135A
CP
CHIMEI 20.1" panel development
CHIMEI
M170E6-L02
BN07-00126B
CQ
"HIGHLAND 17"" LOW PANEL ZPD derivation panel"
CHIMEI
M170E6-L05
BN07-00152A
CR
"CMO 17"" new panel development code"
CHIMEI
M170E6-L05
BN07-00152B
CS
"CMO 17"" ZPD panel code derivation"
CHIMEI
M150X4-L06
BN07-00137B
CT
Chimei 15" Narrow & Slim panel ZPD derivation
CHIMEI
M170E5-L05
BN07-00165A
CTH
CMO 17" new panel development code (GOYA2-PJT)
CHIMEI
M170E5-L05
BN07-00165B
CTZ
CMO 17" ZPD panel(GOYA2-PJT)
CHIMEI
V230W1-L02
BN07-00209A
CMZ
CMO 23" development
CHIMEI
V320B1-L01
BN07-00207A
CMZ
CMO 32" development
CHIMEI
V270W1-L01
BN07-00136A
CMZ
CHI MEI 27" panel development
NEC
SVA150XG04TB
BN07-00225A
BTZ
SVA NEC 15" panel ZPD code
14-10