EC1500-C

TREADMILL

OWNER’S MANUAL

KEYS

Fitness Products, LP

P.O. Box 551239

Dallas, Texas 75239

Table of Contents

Information Page #

Table of Contents

Specification Sheet

Important Safety Information

Before You Start

Warm Up Exercises

Assembly, Moving Instructions

Power Requirements

Console Functions and Descriptions

Program and Operating Instructions

Program Descriptions and Profiles

Belt Adjustments and Tension

Change to MPH or Km/H

Troubleshooting Guide

Parts and Diagrams

Parts List

Warranty Registration (Mail In Form)

15

16

17

18

10 & 11

12

13

14

8

9

6

7

2

3

4

5

Page 2

Specification Sheet

♦ Horsepower (Continuous) 2.5hp

♦ Display Type 5 Window LCD

♦ Electronics One touch

♦ Pre-Set Programs 3

♦ Custom Programs 6

♦ User Programs 0

♦ Heart Rate Interactive No

♦ Power Incline 12%

♦ Roller Diameter 1.9”

♦ Cushioned Deck Yes

♦ Speed Range 0-10mph

♦ Belt Size 18 x 51”

♦ Front Hand Rails Yes

♦ Side Hand Rails Yes

♦ Foot Print 29 x 62”

♦ Foot Print Folded 29 x 29”

♦ Warranty Motor 10 Years

♦ Warranty Parts 2 Years

♦ Warranty Labor 2 Year

PAGE 3

Important Safety Information

1)

WARNING!

Before using this treadmill or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

2)

WARNING!

To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important to review this manual and the following precautions before operation.

SAFETY PRECAUTIONS AND TIPS

♦

It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar with warnings and safety precautions.

♦

This treadmill has a user maximum capacity of 275 pounds.

♦

The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not be placed in a garage, patio, or near water and should never be used while you are wet. KEYS recommends a treadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning.

♦

Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed power cord.

♦

Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with bare feet, sandals, socks or stockings.

♦

Always straddle the belt and allow it to start moving before stepping onto the belt.

♦

Hold on to handrails when adjusting speed, incline, or other controls.

♦

Always examine your treadmill before using to ensure all parts are in working order.

♦

Allow the belt to fully stop before dismounting.

♦

Pets should never be allowed near or on the treadmill.

♦

Do not leave children unsupervised near or on the treadmill.

♦

Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.

♦

Never insert any object or body parts into any opening.

♦

For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.

♦

Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will void the treadmill warranty.

♦

Never leave the treadmill unattended while it is running.

PAGE 4

Before You Start

Thank you for purchasing a KEYS treadmill! This quality product you have chosen was designed to meet your needs for cardiovascular exercise.

Before you start, please read the Owner’s Manual and become familiar with the operation of your new treadmill.

♦

Remember to take the time to perform the stretching exercises provided to avoid injury.

♦

Do not stand on the walking belt while pressing the Power button or Start/Stop button.

♦

Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds.

♦

If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate.

♦

If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the preset treadmill programs or start an exercise program without first contacting and receiving approval from your physician.

♦

To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console.

KEYS recommends a sealed water bottle for beverages consumed while using the treadmill.

♦

Please review the following drawing below to familiarize yourself with the listed parts. This manual

covers several treadmills, so the one pictured below may not be identical to your particular model.

UPRIGHTS

CONSOLE

ELECTRONIC DISPLAY

WATER BOTTLE HOLDER

(WATER BOTTLE NOT INCLUDED)

MOTOR COVER

SIDE HAND RAILS

FRONT HAND RAIL

WALKING BELT

SAFETY LATCH

CIRCUIT BREAKER REAR ROLLER

ADJUSTMENT BOLTS

SES SYSTEM

WHEEL FOOT RAILS

PAGE 5

Warm Up Exercises

EXERCISE GUIDELINES

WARNING ! Before beginning this or any exercise program, you should consult your physician. This is especially important for individuals over the age of 35 or individuals with pre-existing health problems.

Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve an adequate warm-up, perform each stretch three times.

TOE TOUCH STRETCH

Stand bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, back of knees, and back.

HAMSTRING STRETCH

Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible.

Hold for 15 counts, then relax. This will stretch your hamstrings, lower back, and groin.

CALF/ACHILLES STRETCH

With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. To cause further stretching of the Achilles tendon, bend your back leg as well. This will stretch your calves, Achilles tendons, and ankles.

QUADRICEPS STRETCH

With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. This will stretch your quadriceps and hip muscles.

PAGE 6

Assembly, Moving Instructions

Assembly

This KEYS treadmill is shipped in one piece and fully assembled. After opening the box, remove any packing materials from the treadmill. Do not throw away any packing materials until the unit is working properly. Place the base on a clean, level surface. Make sure the electrical cord will easily reach an electrical outlet.

Moving

CAUTION! TO AVOID THE RISK OF INJURY, NEVER ATTEMPT TO MOVE THE TREADMILL

WHILE IT IS IN THE UNFOLDED OPERATING POSITON. TO REDUCE THE POSSIBILITY OF

INJURY WHILE LIFTING, BEND YOUR LEGS AND KEEP YOUR BACK STRAIGHT. AS YOU RAISE

THE TREADMILL, LIFT USING YOUR LEGS, NOT YOUR BACK. IN ORDER TO RAISE OR LOWER

THE TREADMILL SAFELY, YOU MUST BE ABLE TO LIFT 45 POUNDS (20KG). IT IS SUGGESTED

YOU ALWAYS USE THE AID OF A SECOND PERSON WHEN MOVING THE TREADMILL.

With the treadmill in the folded locked position (safety latch is engaged), grasp the handrails and place one foot on the base as shown in the photo below. Next, with a firm grasp on the handrails, place one foot on the center of the base crossbar and carefully tilt the treadmill back until it rolls freely on the wheels. Using extreme caution, move the treadmill to the desired location. To set the treadmill down, place one foot on the center of the base crossbar and carefully lower treadmill onto base in resting position. Do not attempt to move the treadmill over an uneven or rough surface.

PAGE 7

Power Requirements

ARNG!

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A

RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF

YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT

MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT THE OUTLET. HAVE

A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with UL suppressed voltage rating of 400V or less and an electrical rating of 120VAC, 15 amps.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current should the treadmill malfunction. This treadmill comes with an electrical cord with an equipmentgrounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in the drawing below.

PAGE 8

Console Functions and Descriptions

There are five display windows on the control panel to provide feedback information.

TIME WINDOW

♦

TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds)

♦

INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to 0 seconds

SPEED WINDOW

♦

SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments

DISTANCE / CALORIES WINDOW

♦

DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at 10.0

♦

CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time

INCLINE WINDOW

♦

INCLINE: Indicates incline in percent of grade 0-12% in 0.5 increments

CENTER BRICKYARD WINDOW

♦

Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows the change in speed profile across the interval range (1-10) and shows position with a blinking action.

♦

In Program mode, the treadmill will display the name of the program selected. This is shown on the left hand side of the window. In Manual mode, the LAP counter will appear in the top center of the window, counting each 1/4 mile lap in sequence of completion (1, 2, 3, etc.)

CENTER BRICKYARD WINDOW

TIME WINDOW

DISTANCE/CALORIE WINDOW

INCLINE WINDOW SPEED WINDOW

PAGE 9

Program and Operating Instructions

♦

QUICK START / MANUAL MODE

♦

Plug into a surge protector outlet. Attach RED Safety Key to treadmill console.

♦

Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.

♦

Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be entered. The TIME window will flash.

♦

Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) button.

♦

To end your workout, press START/STOP button. Belt will gradually slow to zero.

♦

To pause your workout, press PAUSE.

♦

To re-start after pausing: Press the PAUSE button. WARNING: THE TREADMILL BELT WILL

RESUME AT THE SPEED THE TREADMILL WAS MOVING BEFORE PAUSING.

♦

Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting started. After pressing the POWER button, the time window will blink. Use the SPEED/TIME + or – arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME window will now be flashing. Using the same + or – arrows, select the speed for your workout, then press

ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button.

ENTER

INCLINE SPEED/TIME

PAGE 10

START/STOP

PAUSE

POWER

Program and Operating Instructions

PROGRAM MODE

♦ Plug treadmill into a surge protector outlet . Attach RED Safety Key to treadmill console.

♦ Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.

♦ Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window will flash.

♦ There are four (3) pre-set and six (6) custom pre-set programs on the EC1500-C. The treadmill includes FAT

BURN, CARDIO, and WARM-UP programs. Select the program by pressing the appropriate button.

♦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving.

♦ CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, Warm-up) can be customized in the P1 or P2 mode. After making the program selection, the center window will read “OP”. The

”OP” refers to “original program” and is preset. The program name you select will display to the left of the

“OP”. Press the same program button once more and the center window will read P1. The “P1” mode is now accessed. You can now program the Time, Speed, and Incline in P1 mode, which will be saved for future workouts.

1) The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press

ENTER PROGRAM.

2) The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your

workout. Press ENTER PROGRAM.

3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press

ENTER PROGRAM.

To start, press the START/STOP button. To access P2 mode, press the selected program button three times

(once for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings.

♦ TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the

P1 or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For instance to change to a new setting in P1-FAT BURN, press the FAT BURN button twice to access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change the program.

FAT BURN

CARDIO

WARM UP

ENTER

START/STOP

PAUSE

POWER

INCLINE

PAGE 11

SPEED

Program Profiles

8

7

6

5

12

11

10

9

4

3

2

1

SPEED

INCLINE

1 2 3 4 5 6 7 8 9 10

The Fat Burn Program is designed to vary the treadmill elevation, while maintaining a constant walking belt speed.

8

7

6

5

12

11

10

9

4

3

2

1

SPEED

INCLINE

1 2 3 4 5 6 7 8 9 10

The Cardio Program is designed to vary the treadmill Speed, while maintaining a constant Elevation.

8

7

6

5

12

11

10

9

4

3

2

1

SPEED

INCLINE

1 2 3 4 5 6 7 8 9 10

The Warm Up Program is designed to gradually increase the treadmill Speed and Elevation in the first segment (warm up) and gradually decrease the treadmill Speed and Elevation in the last segment (cool down). This is also known as a

Plateau program.

PAGE 12

Belt Adjustment and Tension

WARNING! Do not overtighten rollers! This will cause premature roller bearing failure!

Belt adjustment and tension performs two functions: adjustment for tension and centering. Your new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the procedures below if the belt shifts to the left or right while walking:

WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1)

First, turn treadmill on to run at 1 mph. Using the hex key provided, turn the left rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself by moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions.

WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2)

First, turn the treadmill on to run at 1 mph. Using the hex key provided, turn the right rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself moving back towards the center.

Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions.

WALKING BELT IS SLIPPING DURING USE (Diagram 3)

First, unplug the power cord from the surge protector. Using the hex key provided, turn both left and right rear roller adjustment bolts the same distance, usually a ¼ turn in the clockwise direction. Plug the power cord back into the surge protector and run the treadmill at 2.5 mph. You should now walk on the belt to determine if the belt is still slipping. Repeat the above procedure until the walking belt is not slipping. The tension should be just tight enough not to slip.

♦

Turning the hex key counter clockwise brings the rear rollers and belt towards you.

♦

Turning the hex key clockwise pushes the rear roller and belt away form you.

PAGE 13

Change Miles per hour to Kilometers per hour

Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills are calibrated at the factory for British Units (miles per hour). To change the display to read in kilometers, follow the steps described here:

1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the console.

2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside of the

console (see diagram below).

3) Depressing the calibration mode switch ONCE; CL11 should appear in the TIME window.

4) Pressing the SPEED +/- button will activate your choice.

5) To accept the setting, press the POWER button.

Page 14

Troubleshooting Guide

Treadmill will not start.

1) Is the RED Safety Key Attached to the Console?

2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements” on page 8)

3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.

Wait five minutes and then press the switch back in.

4) Check the house electrical breaker box and the circuit breaker for the room where the treadmill is located. If it has tripped, reset or have an electrician replace the breaker in home.

5) Have an electrician check for inadequate voltage at the outlet.

Treadmill loses power during use.

1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.

Wait five minutes and then press the switch back in.

2) Check the house electrical breaker box and the circuit breaker for the room where the treadmill is located. If it has tripped, reset or have an electrician replace the breaker in home.

3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.

Treadmill walking belt slows during use.

1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less and the surge protector is securely plugged into the outlet.

2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.

Treadmill walking belt slips or is not centered on rear roller.

1) Refer to “Belt Adjustment and Tension” section on page 13.

2) Need help? Call Keys Technical Service at (888) 340-0482.

Treadmill Error Messages.

Your treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not operate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 340-0482.

Page 15

Parts & Diagrams

1. 05-0001-Extrusion side board deluxe/left

2. 05-0001-Extrusion side board deluxe/right

3. 04-0008-Belt walk spliced 18 x 105WW

4. 24-0006-Front roller assembly

5. 09-0013-Rear roller assembly

6. 03-0004-Walkboard waxed

7. 06-0008-End cap

8. 12-0022-Actuator 400lb Maytech

9. 06-0026-Motor base pan

10. 06-0079-Small motor fan

11. 12-0033-Motor MCM 2.5HP

12. 04-0004-Poly V belt 190J8

13. 06-0025-Motor cover w/wings

14. 10-0003-Foam grips

15. 07-0026-Electronics 5 window brickyard

16. 24-0104-Console assembly-EC1500C

17. 08-0051-Motor controller

Page 16

Encore 1500-C Parts List

Parts List - EC1500C

PART # DESCRIPTION

04-0004

04-0008

05-0011

06-0130

06-0008

06-0014

06-0019

06-0020

06-0021

09-0013

12-0033

12-0022

13-0003

13-0011

02-0040

03-0004

02-0036

05-0001

05-0014

06-0004

06-0005

06-0012

06-0125

06-0009

06-0133

10-0002

06-0016

02-0022

14-0028

14-0069

14-0027

06-0022

06-0025

06-0026

24-0104

10-0003

10-0004

19-0019

19-0032

ROLLER-REAR 20MM SHAFT

MOTOR MCM 2.5HP

ACTUATOR 400LB MAYTECH

HARNESS-ENCODER

POWER CORD-90"

RETAINER-GUIDE TUBE

WALKBOARD WAXED

BELT-POLY V 190J8

BELT WALK SPLICED 18x105WW

EXTRUSION-EN CAP JOINT

PULLEY 8 GROOVE-190JA

ENCAP

BUSHING-STRAIN RELIEF #1237

CENTER BASE PAN

END BASE PAN

CLAMP-WIRE 3367 7/16

GUIDE-RESET TUBE

MOTOR COVER CSA

FRONT BOTTOM PAN-CSA

COMPLETE CONSOLE ASSEMBLY

FOAM GRIP 1.5x14.75

RUBBER FOOT

GUIDE BELT GALVANIZED

BRKT-SPRING ANCHOR

SCREW-PPH 8x 5/8 GREEN HEAD

EXTRUSION-SIDE BOARD-DELUXE

BOTTOM PAN JOINT 21 1/2

PLUG-BASE 1.5x3"-16GA

PLUG-DOME 1.5-16G

WHEEL 3"

SPACER FOR UPRIGHT

GLIDE-BASE EXTENSION

WHEEL-ROLLER 2"

ISOLATOR BOARD

WIRE TIES

NYLOCK NUT HEX 10-24

DECAL-CIRCUIT BREAKER-ALL

DECAL-END CAP LOGO-BLK/TEAL/RED

DECAL-EMERGENCY STOP-RED

INST PACKET-EC1500C

QTY PART #

1 15-0103

1 14-0205

1 19-0097

1 02-0041

1 02-0050

1 02-0051

1 02-0053

1 02-0054

1 02-0068

1 02-0092

1 06-0079

1 06-0088

1 08-0004

1 08-0047

1 08-0051

1 08-0077

MANUAL-EC1500

DECAL-DISCONNECT-MOTOR COVER

BRKT-ENCODER-MCMILLIAN

SCREW-PPH 8-18x5/8" S/D-FOOTLATCH

NUT-NYLOCK HEX 1/4-20

SCREW-SH CAP 10-24x1 1/4"

SCREW-SHCS 1/4-20x3/4"

SCREW-HWH MACH 8-32x3/8"

WASHER-FLAT SAE 5/16

SCREW-PHTR#8x3/4" AB BLACK

FAN-MCM MOTOR-5" W/1/2"SHAFT

SLEEVE-MOTOR TENSION 1/4"

CIRCUIT BREAKER 15AMP

ENCODER-OPTICAL-ALEPH

CONTROLLER-REVISED 08-0014

CORE-FERRITE

DESCRIPTION

1 24-0006

1 13-0007

FRONT ROLLER ASSEMBLY

WIRE-BREAKER 6"

1 13-0016 HARNESS-CONTROL PANEL

1 02-0002A SPRING-DECK LIFT

2 02-0004

2 02-0005

2 02-0006

2 02-0007

SCREW-8x5/8 PHIL PH AB BLACK

SCREW-8x5/8 PHIL HILO BLACK TPB

BOLT-HEX 5/16-18x5 1/2 GRADE 5-ZP

NUT-5/16-18 NYLOCK ZP

2 02-0008

2 02-0024

2 02-0025

2 02-0027

2 02-0009

2 02-0013

2 02-0031

4 02-0033

4 02-0014

8 02-0015

12 02-0016

6 02-0017

1 02-0018

2 14-0089

1 22-0001

BOLT-HEX 5/16-18x 3/4"GRADE 2-ZP

CARRIAGE BOLT 5/16 X 1GRADE 5 ZP

WHEEL AXLE 2"

NUT-T HF 14209H-DB

NUT-HEX 5/16 WIZ-FL-LK-ZP

WASHER-LOCK 1/4"

HEX BOLT, 3/8-16 X 1 3/4 GRADE 5 ZP

WASHER-#10 EXTERNAL STAT

HEX BOLT, 1/4-20x2 1/2"GRADE 5 ZP

SPRING WASHER

HEX BOLT 3/8-16x2 1/2" GRADE 5

NYLOCK HEX NUT 3/8-16

PUSH NUT 3/8 HAT BLACK 375012

DECAL-STARBURST-WASDECK-YELLOW

ACTUATOR CONNECTION ASSEMBLY

1

QTY PART # DESCRIPTION

1 02-0108 SCREW-PPH 10 X 5/8"

1 02-0113

1 02-0123

SCREW-HWH SLOTTED 8-18 X 3/4" AB ZP

WASHER-FENDER 1/4 X 1"

1 16-0002

1 16-0001

2 16-0003

2 16-0004

BOX BOTTOM

BOX TOP

PAD-FRONT WHEEL

PAD-REAR

1 16-0027

2 18-0003

7 18-0004

1 18-0006

1 19-0013

1 19-0134

1 19-0015

1 20-0003

1 23-0003

PAD-UPRIGHT

LINKAGE-BASE EXTENSION-RIGHT

LINKAGE-BASE EXTENSION-LEFT

SPRING-MOTOR TENSION-PRESET

LATCH-FOOT LOCKING MECHANISM

BRKT BASE ELEVATION

BRKT-MOTOR COVER

PROC-ACTUATOR EXT. TB-17-0011

REAR ELEVATION ASSEMBLY-WELDED

1 23-0090

1 20-0008

1 23-0001

4 10-0012

40 10-0017

8 11-0002

1 11-0003

3 14-0003

UPRIGHT ASSEMBLY

PROC-BASE EXTENSION TB 17-0010

DECK FRAME ASSEMBLY

BUMBER LATCH

TAPE-FOAM-1" X 75FT

BUSHING-REAR ELEVATION

BUSHING-UPRIGH POVOT

DECAL-MOTOR COVER SES-ALL-GRAY

3 14-0016

2 14-0023

2 14-0024

8 14-0025

DECAL-MOTOR COVER-EC1500-TEAL

DECAL-NO LIFT - ALL FOLDS

DECAL-SAFETY LATCH-ALL FOLDS

DECAL-WARNING FOLDING-ALL FOLDS

3 02-0099 WASHER

8 02-0028 SWITCH-MAGNETIC LIKK-YIHAN

2 02-0038

1 06-0024

WRENCH-ALLEN 3/16 SHAFT ARM

CLIP-ALLEN WRENCH

11 06-0084

4 14-0321

1 02-0019

3 02-0020

4 02-0021

2 14-0026

1 14-0204

BAG-PLASTIC 12 X 12 3 MIL-INST PACKET

10 YEAR WARRANY DECAL

CARRIAGE BOLT 10-24x1 1/2"

SCREW-SHCS 1/4-20x2 1/2"

WASHER-9/32 5/8 1/8 THICK ZP

DECAL-WARNING CONSOLE-ALL-GRAY

DECAL-OPERATION INSTALL

7

1

1

1

1

1

1

1

1

1

1

2

1

QTY

1

1

2

1

1

1

1

1

1

1

1

4

2

2

1

1

1

1

0.5

2

2

1

1

2

1

1

Page 17

KeysEncore 1500-C Treadmill KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY

PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.

This Limited Warranty applies in the United States, Canada, and Mexico to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty period on the ENCORE 1500-C to the original purchaser is (lifetime) on the frame, (10) years on the motor, (2) years parts, and (2) year labor.

Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness authorized dealer/technician unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the warranty will be void unless accompanied by written authorization by Keys Fitness).

During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the product if it becomes defective, malfunctions, or otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty.

To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts determined to be defective must be returned to

Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.

This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or

(e) as a result of service by anyone other than Keys, or an authorized Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any

Product be submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt of payment or acceptable arrangements for payment.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED

WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE

RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty.

PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR TREADMILL

WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA. Thank you for your business! PLEASE MAIL WARRANTY CARD TO:

KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355

.

KEYS FITNESS TREADMILL WARRANTY REGISTRATION

FIRST M.I. LAST

TELEPHONE

ADDRESS

CITY

DATE OF PURCHASE

Name of store or company where purchased:

How do you plan to use the treadmill?

Walk____ Run_____ Both_____

Who will use the treadmill?

Male____ Female_____ Both_____

How many family members? _____

AGE: 15-24____ 25-34____

35-44____ 45-54____

55-64____ 65 +_____

STATE ZIP

APT. NO.

MODEL NO.

SERIAL NO.

Where did you learn about treadmills?

TV____ Radio____ Friend____

In Store Display____ Salesperson___

Print ad/flyer____ Internet______

Why did you purchase a treadmill?

Dr.’s Orders____ Loose Weight____

In-home convenience____

Improve Cardiovascular Fitness___

Safety from outdoors____

Other __________________________

Page 18

How important are each feature:

Least Most

Unique Features

Horsepower

Warranty

Price

Look/Design

Folding Feature

Other Comments:

_______________

_______________

_______________

_______________

KEYS FITNESS respects the rights of your privacy. Our company will not sell or distribute to others the information above. This information is used to track our product quality and to contact you in the event of a product safety concern. It may be used to offer you future Keys products only through the mail. Please check here if wish not to receive any additional information on Keys products.