Sharp CD-SW300H Operating instructions

XL-MP130
MINI COMPONENT SYSTEM
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
CD-SW300 Mini Component System consisting of CD-SW300 (main
unit), CP-S300 (front speaker) and CP-SW300 (Subwoofer).
MODEL
CD-SW300
OPERATION MANUAL
Accessories
Please confirm that the following accessories are included.
Remote control 1 AM loop antenna 1
(RRMCGA083AWSA) (QANTL0010AWZZ)
Note:
Only the above accessories are included.
03/12/17
CD-SW300 FRONT.fm
FM antenna 1
(92LFANT1535A)
CD-SW300
SPECIAL NOTES
Important Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
NOTES
It is the intent of Sharp that this product be used in full compliance
with the copyright laws of the United States and that prior permission
be obtained from copyright owners whenever necessary.
Licensed under one or more of U.S. Pat. 4,972,484, 5,214,678,
5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985,
5,740,317, 5,777,992, 5,878,080 or 5,960,037.
0303
0012
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
0012
Caution - use of controls or adjustments or performance
of procedures other than those specified herein may result in hazardous radiation exposure.
0012
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit.
Please retain this information.
Model number
.......................................................
Serial number
.......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202
2
03/12/17
CD-SW300 02-14.fm
IMPORTANT SAFETY INSTRUCTIONS
be read before the product is operated.
2 Retain Instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on
a bed, sofa, rug, or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been
adhered to.
11 Power Sources - This product should be operated only from the type
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
6 Attachments - Do not use attachments not recommended by the prod-
12 Grounding or Polarization - This product may be equipped with a
5 Cleaning - Unplug this product from the wall outlet before cleaning.
uct manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
9 A product and cart combination should be moved with
13 Power-Cord Protection - Power-supply cords should be routed so
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
14 Protective Attachment Plug - The product is equipped with an at-
Important Instruction
1 Read Instructions - All the safety and operating instructions should
CD-SW300
that they are not likely to be walked on or pinched by items placed
upon or against them.
tachment plug having overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has
used a replacement plug specified by the manufacturer that has the
same overload protection as the original plug.
3
03/12/17
CD-SW300 02-14.fm
CD-SW300
IMPORTANT SAFETY INSTRUCTIONS (continued)
15 Outdoor Antenna Grounding - If an outside antenna or cable system
19 Object and Liquid Entry - Never push objects of any kind into this
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
Important Instruction
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERV ICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
P OWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
16 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
17 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
18 Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
20 Servicing - Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22 Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
24 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25 Heat - The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
0304
4
03/12/17
CD-SW300 02-14.fm
Contents
CD-SW300
Page
General Information
ENERGY STAR® Program Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 10
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 - 13
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Preparation for Use
CD or MP3/WMA disc Playback
To comply with the ENERGY STAR® standards mentioned above,
please cancel the demonstration mode, as described on page 13.
Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . . . .17 - 20
Advanced CD or MP3/WMA disc playback . . . . . . . . . . . .21 - 23
MP3/WMA navigation (only for MP3/WMA files) . . . . . . . .24 - 27
Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 - 29
ENERGY STAR® is a U.S. registered mark.
Tape Playback
Listening to a cassette tape (TAPE 1 or TAPE 2) . . . . . . .30 - 31
Tape Recording
Important Instruction
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Setting the clock (Remote control only). . . . . . . . . . . . . . . . . . 16
Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .31 - 33
Advanced Features
Timer and sleep operation (Remote Control only) . . . . . .34 - 37
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . .38 - 39
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 - 41
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 - 43
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . .Back cover
5
03/12/17
CD-SW300 02-14.fm
CD-SW300
Precautions
General
Please ensure that the equipment is positioned in a well ventilated
area and ensure that there is at least 4" (10 cm) of free space
along the sides, top and back of the equipment.
4" (10 cm) 4" (10 cm)
Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
Do not remove the outer cover, as this
may result in electric shock. Refer
internal service to your local SHARP
service facility.
4" (10 cm)
General Information
4" (10 cm)
Table
Floor
Do not place subwoofer system on the
same surface as main unit to prevent
sound interruption during playback.
Use the unit on a firm, level surface free from
vibration.
Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equipment (home computers, facsimiles, etc.)
which generate electrical noise.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures higher than
140˚F (60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and then
turn on your system.
In case of an electrical storm, unplug the
unit for safety.
AC INPUT
This unit should only be used within the range of 41˚F - 95˚F
(5˚C - 35˚C).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of
accident causing damage. SHARP will not be held responsible for
any damage resulting from use of this unit with a voltage other than
that which is specified.
Volume control
The sound level at a given volume setting depends on speaker efficiency, location, and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on
with the volume control setting up high, or while continually listening
at high volumes.
6
03/12/17
CD-SW300 02-14.fm
Controls and indicators
CD-SW300
Reference page
1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 15
6. Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8. Tape 1 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 30
9. Headphone Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
10. Game/Video Input Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
11. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 18
12. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 18
13. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
14. CD or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . 19, 31
15. CD Play or Repeat, Tape Play Button . . . . . . . . . . . 18, 22, 30
16. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . 16, 19, 29, 31
17. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button . . . . . . 16, 19, 29, 31
18. Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 30
19. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General Information
Front panel
7
03/12/17
CD-SW300 02-14.fm
CD-SW300
Controls and indicators (continued)
Display
1
2
3
4
5
6
7 8 9
11 12 13
16 17
General Information
10
18
14
19
15
3
4
5
6
7
8
9
1
10
AC INPUT
2
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2. MP3/WMA Folder Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 24
3. MP3/WMA Title Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4. MP3 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8. Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9. Tape 2 Record Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10. MP3/WMA Total Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 25
11. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
12. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 28
13. FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 28
14. Tape Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
15. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 29
16. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
17. Disc Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 22
18. Disc Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
19. Disc Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Rear panel
Reference page
1. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3. FM 75 Ohms Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. FM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . . 12
5. AM Loop Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . . . . 12
6. Subwoofer Light-up Jack . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7. Speaker Light-up Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8. Video out Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9. Subwoofer Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10. Front Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8
03/12/17
CD-SW300 02-14.fm
CD-SW300
Front Speaker
1
2
4
1. Tweeter
2. Super Tweeter
3. Woofer
4. Bass Reflex Duct
5. Speaker Wire
6. Speaker Light-Up Wires
6
5
Subwoofer
1. Subwoofer
2. Bass Reflex Duct
3. Subwoofer Light-Up Wires
4. Speaker Wire
1
2
3
General Information
3
4
9
03/12/17
CD-SW300 02-14.fm
CD-SW300
Controls and indicators (continued)
Remote control
1
General Information
2
7
8
9
13
17
14
18
15
19
20
10
11
16
22
21
23
3
4
26
24 25
27 28
5
6
12
29
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 14
2. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 18
3. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 16, 34, 37
4. Character Input/Disc Direct Search Buttons . . . . . . . . 21, 26
5. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . 15
6. Extra Bass (Surround)/Demo Button . . . . . . . . . . . . . . . . . 15
7. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10. Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 15
13. Disc Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . 15, 23
14. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
15. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
16. Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
17. Memory Button . . . . . . . . . . . . . . . . . . . . 16, 23, 27, 29, 34, 37
18. Disc Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
19. Disc Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . 18, 22
20. Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
21. Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . 32, 33
22. Tuning Up, Cursor Up Button . . . . . . . . . . . . . . . . . . . . . . . 25
23. Disc Track Up or Fast Forward, Tape Fast Forward,
Tuner Preset Up, Time Up, Cursor Right Button . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 19, 29, 31
24. Disc Track Down or Fast Reverse, Tape Rewind,
Tuner Preset Down, Time Down, Cursor Left Button . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 19, 29, 31
25. Tuning Down, Cursor Down Button . . . . . . . . . . . . . . . . . . 25
26. MP3/WMA Navigation Mode Select Button . . . . . . . . . . . . 25
27. Character Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 26
28. MP3/WMA Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . 20
29. Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10
03/12/17
CD-SW300 02-14.fm
System connections
CD-SW300
Make sure to unplug the AC power cord before any connections.
Antenna connection (see page 12)
FM antenna
AM loop antenna
Subwoofer
Preparation for Use
Left speaker
Right speaker
AC INPUT
Speaker light-up wire
Speaker connection
(see page 12)
Speaker light-up wire
Subwoofer
Light-up wire
AC Outlet
(AC 120 V, 60 Hz)
AC power connection (see page 13)
11
03/12/17
CD-SW300 02-14.fm
System connections (continued)
2. Connect the subwoofer light-up wire to the SUBWOOFER
LIGHT-UP jack.
AM loop
antenna
FM
antenna
AC INPUT
Black
White
Speaker Light-Up connection
GND
AM
75 OHMS
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
< Assembling >
< Attaching to the wall >
LEFT SPEAKER
RIGHT SPEAKER
AC INPUT
Wall
Screws (not supplied)
Speaker connection
FRONT SPEAKERS:
Connect the black wire to the FRONT SPEAKERS minus (-) terminal, and the red wire to the FRONT SPEAKERS plus (+) terminal.
SUBWOOFER:
1. Connect the black wire to the SUBWOOFER minus (-) terminal,
and the red wire with purple insulation tube to the SUBWOOFER
plus (+) terminal.
Purple
AC INPUT
12
Connect the speaker light-up wires to the SPEAKERS LIGHT-UP
jacks for speaker illumination. To turn off the speaker light-up
feature, press the CLEAR/DIMMER button on the remote control for
2 seconds or more.
LEFT
ANTENNA
FM
SUBWOOFER
SPEAKERS
LIGHT-UP
Preparation for Use
Antenna connection
Supplied FM antenna:
Connect the FM antenna wire to the
FM 75 OHMS jack and position the FM
antenna wire in the direction where the
strongest signal can be received.
Supplied AM loop antenna:
Connect the AM loop antenna to the
AM and GND terminals. Position the
AM loop antenna for optimum
reception. Place the AM loop antenna
on a shelf, etc., or attach it to a stand
or a wall with screws (not supplied).
RIGHT
CD-SW300
Red
Black
Note:
Placing the right speaker light-up wire to the RIGHT jack and the left
speaker light-up wire to the LEFT jack.
Caution:
Never mistake the FRONT SPEAKERS and the SUBWOOFER
terminals. The unit or the speakers may be damaged.
If you use other speakers with an impedance lower than that
specified, the unit may be damaged. Front speakers: 6 ohms,
Subwoofer: 12 ohms.
Do not mistake the right and the left
channels. The right speaker is the one on
the right side when you face the unit.
Do not let the bare speaker wires touch
each other.
Do not stand or sit on the speakers. You may
be injured.
Do not allow any objects to fall into or to be
Incorrect
placed in the bass reflex duct.
03/12/17
CD-SW300 02-14.fm
CD-SW300
Subwoofer
Left speaker Main unit Right speaker
Table
Floor
Note:
The speaker grilles are not removable.
AC power connection
After checking all the connections have been made correctly, plug
the AC power cord of this unit into the AC outlet. If you plug in the
unit first, the unit will enter the demonstration mode.
Demonstration mode
The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll and the subwoofer will light up in flashing mode.
To cancel the demonstration mode:
When the unit is in the power
stand-by mode (demonstration
mode), press the X-BASS (SURROUND)/DEMO button. The unit
will enter the low power consumption mode and the subwoofer light
up will be off.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS
(SURROUND)/DEMO button again.
AC INPUT
AC outlet
(AC 120 V, 60 Hz)
Notes:
The unit will start the tape initialization when plugged in to the AC
outlet. During this process, initializing sound will be heard and the
unit cannot be turned on. Wait until the process is finished.
Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
Cooling fan:
The main unit is built with a cooling fan at the rear of the unit for
improved cooling. Please do not cover the opening of the fan with
any obstacles, as this will block proper ventilation.
Note:
When the power is on, the X-BASS (SURROUND)/DEMO button can
be used to select the extra bass mode.
Outdoor FM antenna
Use an outdoor FM antenna if you require better reception. Consult
your dealer.
Preparation for Use
Placing the speaker system
There is no distinction between the right and left speakers.
ANTENNA
FM
GND
AM
Outdoor
FM antenna
75 OHMS
75 ohms
coaxial cable
AC INPUT
Note:
When an outdoor FM antenna is used, disconnect the supplied FM
antenna wire.
03/12/17
CD-SW300 02-14.fm
13
CD-SW300
Remote control
Battery installation
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
2
Preparation for Use
3
Open the battery cover.
Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
Close the battery cover.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 11 - 13).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Remote sensor
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
8" - 20"
(0.2 m - 6 m)
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to malfunction.
Battery removal:
Open the battery cover and pull up the battery to take out.
14
03/12/17
CD-SW300 02-14.fm
General control
CD-SW300
Volume control
Main unit operation:
When the VOLUME control is turned
clockwise, the volume will increase.
When it is turned counterclockwise, the
volume will decrease.
Remote control operation:
Press the VOLUME (+ or -) button to increase or decrease the volume.
0 ..... 30 MAXIMUM
Equalizer
To turn the power on
Press the ON/STAND-BY button to turn the power on.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
Illumination light control
When the power is turned on, light illuminates around the display.
To turn on/off the light, hold down the CLEAR/DIMMER button on
the remote control for 2 seconds or more.
Subwoofer light up control
The subwoofer will light up according to the level of the music
source played back. To turn on/off the light, hold down the CLEAR/
DIMMER button on the remote control for 2 seconds or more.
Volume auto fade-in
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
When the power is first turned on, the unit will enter FLAT mode.
When the EQUALIZER MODE button is pressed, the current mode
setting will be displayed. To change to a different mode, press the
EQUALIZER MODE button repeatedly until the desired sound mode
appears.
In CD/TUNER/TAPE mode
In GAME/VIDEO mode
FLAT
No equalization.
FLAT
No equalization.
ROCK
For rock music.
ROCK
For rock music.
CLASSIC For classical music.
POPS
For pop music.
VOCALS Vocals are enhanced.
JAZZ
For jazz.
Basic Operation
Surround mode
When the X-BASS (SURROUND)/
DEMO button is pressed, the unit will enter the surround mode and adjust low
bass and high frequency automatically
according to volume input. To cancel this
mode, press the X-BASS (SURROUND)/
DEMO button again.
CLASSIC For classical music.
ACTION
For action games.
SPORTS For sports games.
RACING
For car racing games.
Note:
If the EQUALIZER MODE button is pressed in the surround mode, it
will be canceled automatically.
15
03/12/19
CD-SW300 15-25.fm
CD-SW300
Setting the clock (Remote control only)
5
Press the
or
button to adjust the hour and
then press the MEMORY button.
Press the
or
button once to advance the time by
1 hour. Hold it down to advance continuously.
Basic Operation
6
Press the
or
button to adjust the minutes and
then press the MEMORY button.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
3
Press the ON/STAND-BY button to turn the power on.
4
Press the
or
button to select 12-hour or 24hour display and then press the MEMORY button.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select "CLOCK", and press the MEMORY button.
"AM 12:00"
"AM 0:00"
"0:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
Press the
or
button once to advance the time by
1 minute. Hold it down to change the time in 5-minute intervals.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.
[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to display the
time.
The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will flash to confirm the time display when the AC power supply is restored after a power failure or
unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" does not
appear in step 3, step 4 (for selecting the 12-hour or 24-hour display) will be skipped.
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 41 for details.]
2 Perform "Setting the clock" from step 1.
16
03/12/19
CD-SW300 15-25.fm
Listening to a CD or MP3/WMA disc
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3.
MP3 is a type of audio code which is processed by significant
compression from the original audio source with very little loss
in sound quality.
This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and
VBR files.
During VBR file playback, time counter in the display may differ
from its actual playback time.
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit turns on and
the "CD" function is activated.
CD / button on the remote control: The unit turns on and CD
playback starts (regardless of the last function).
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TAPE,TUNER,GAME/VIDEO).
Auto power off function:
In the stop mode of CD, MP3 or WMA operation, the main unit enters
the stand-by mode after 15 minutes of inactivity.
WMA:
WMA files are Advanced System Format files that include audio
files which are compressed with Windows Media Audio codec.
WMA is developed by Microsoft as an audio format file for Windows Media Player.
"MP3" or "WMA" indicator will light up after the unit reads information on an MP3 or WMA disc.
CD or MP3/WMA disc Playback
This system can play back a standard CD, CD-R/RW in the CD format
and CD-R/RW with MP3 or WMA files, but cannot record on them.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the device that was used for recording.
CD-SW300
17
03/12/19
CD-SW300 15-25.fm
CD-SW300
Listening to a CD or MP3/WMA disc (continued)
1
2
3
CD or MP3/WMA disc Playback
4
Press the ON/STAND-BY button to turn the power on.
Press the CD button.
Press the 1 button and within 5 seconds, press the
button to open the disc tray 1.
Place the disc on the disc tray 1, label side up.
Be sure to place 3" (8 cm) disc in the middle of the disc trays.
5" (12 cm)
5
3" (8 cm)
Press / button to close the disc tray 1.
MP3 indicator
WMA indicator
[CD]
[MP3/WMA]
Total number of
Total playing
Total number Total number
tracks on the disc time of the disc of folders
of files
Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
6
You can place discs on the trays 2 - 5 by following steps
3 - 5.
7
Press the
/
button to start playback.
Disc play indicator
18
03/12/19
CD-SW300 15-25.fm
CD-SW300
Various disc functions
Function
Main unit
Remote
control
Operation
Play
Press in the stop
mode.
To exchange other discs while playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5
seconds, press the button and exchange discs.
Stop
Press in the playback
mode.
To remove the discs:
In the stop mode, press the
press the button.
Pause
Press in the playback
mode. Press the /
button to resume playback from the paused
point.
Press in the playback
or stop mode.
If you press the button
in the stop mode,
press the / button
to start the desired
track.
Press and hold down
in the playback mode.
Release the button to
resume playback.
1-
5 button and within 5 seconds,
Caution:
Do not place two discs in one disc tray.
Do not play discs of special shapes (heart, octagon, etc.) as it
may cause malfunctions.
Do not push the disc tray while it is moving.
If the power fails while the tray is open, wait until the power is restored.
If the disc tray is stopped with force, "ER-CD20" will appear on the
display for 3 seconds and the unit will not function. If this occurs,
press the ON/STAND-BY button to enter the power stand-by
mode and then turn the power on again.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
If a disc is damaged, dirty, or loaded upside down, the disc will
skip or not play.
Track up/
Track down
Fast forward/Fast
reverse
CD or MP3/WMA disc Playback
Playback will begin from track 1 on disc 1. After that disc finishes
playing, the next disc will automatically play.
After the last track on the fifth disc is played, the unit will stop automatically.
When there is no disc in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a disc.
19
03/12/19
CD-SW300 15-25.fm
CD-SW300
Listening to a CD or MP3/ WMA disc (continued)
CD or MP3/WMA disc Playback
Notes for CD:
Track up/track down is possible only within individual discs.
Fast forward/fast reverse is possible only within individual discs.
When the end of the last track is reached during fast forward,
"END" will appear on the display and CD operation will be paused.
When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
Notes for MP3/WMA discs:
Track up/track down is possible only within individual discs.
The sound is heard during fast forward/fast reverse with a CD, but
not with an MP3/WMA disc. For fast forward or fast reverse of an
MP3/WMA disc, refer to playback time on the display.
Fast forward/fast reverse is possible only within individual tracks.
When the end of the track is reached during fast forward, the next
track will be played. Playback of the track will begin when its beginning is reached during fast reverse.
To change the display (MP3/WMA discs only)
While a disc is playing, press the DISPLAY
button.
Each time the button is pressed, the display
will change as follows.
Track number Elapsed
playback time
File name
20
03/12/19
CD-SW300 15-25.fm
Folder name
Advanced CD or MP3/WMA disc playback
1
Press one of the
1-
5 buttons to select the desired disc.
Direct track search
By using the direct search buttons, the desired tracks on the current
disc can be played.
Use the direct search buttons on
the remote control to select the desired track while playing the selected disc.
Selected track number
Selected disc number
Within 5 seconds, press the / button on the main unit.
The direct search buttons allow you to select up to number 9.
When selecting number 10 or higher, use the "+10" button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "3" button.
Playback will begin from track 1 on the chosen disc.
After the last track on the last disc is played, the unit stops automatically.
Note:
If a disc tray with no disc is selected, playback will not start and the
disc indicator will disappear.
To stop playback:
Press the (CD ) button.
B. For example, to choose 30
1 Press the "+10" button three times.
2 Press the "0" button.
If the direct search buttons are pressed while the disc is stopped,
press the / button to start the desired track on the current disc.
CD or MP3/WMA disc Playback
To specify a disc to play
You can play a disc by specifying the disc number.
CD-SW300
Notes:
A track number higher than the number of tracks on the disc cannot be selected.
During random play, direct search is not possible.
21
03/12/19
CD-SW300 15-25.fm
CD-SW300
Advanced CD or MP3/WMA disc playback (continued)
Repeat play
Repeat play can play all 5 discs, all tracks on a chosen disc, or a programmed sequence continuously.
CD or MP3/WMA disc Playback
To repeat one disc:
Press the / button twice.
Random play
The tracks on the disc(s) can be played in random order automatically.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
To repeat all tracks on up to 5 discs:
Press the / button three times.
To repeat desired tracks:
Perform steps 1 - 6 in "Programmed play" section on page 23 and
then press the / button twice.
To cancel repeat play:
Press the / button again.
" " will disappear.
To cancel random play:
Press the / button.
"R" will disappear
Notes:
If you press the
button during random play, you can move to
the next track by the random operation. On the other hand, the
button does not allow you to move to the previous track. The beginning of the track being played will be located.
In random play, the unit will select and play tracks automatically.
(You cannot select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the
) button. Otherwise, the disc(s) will play continuously.
22
03/12/19
CD-SW300 15-25.fm
(CD
CD-SW300
1
2
While in the stop mode, press the
MEMORY button to enter the programming save mode.
To cancel the programmed play mode:
While in the stop mode and the "MEMORY" indicator is lit, press the
CLEAR/DIMMER button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be
cleared.
Press one of the 1 - 5 buttons
to select the desired disc.
Selected disc number
3
Press the direct search buttons
on the remote control to select
the desired track.
Selected track number
You can also select a track by pressing the
or
button.
4
Press the MEMORY button to
save the track number.
5
Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be
programmed.
If you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR/DIMMER button.
6
Press the
To clear the programmed selections:
Press the CLEAR/DIMMER button on the remote control while the "MEMORY" indicator
is flashing.
Each time the button is pressed, one track will
be cleared, beginning with the last track programmed.
Adding tracks to the program:
If a program has been previously stored, the "MEMORY" indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
To check which tracks are programmed:
While the unit is stopped in the programmed play mode, press the
or
button.
Notes:
When a disc with programmed tracks is ejected, the program is
automatically canceled.
Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed
selections will not be cleared.
During the program operation, random play is not possible.
CD or MP3/WMA disc Playback
Programmed play
You can choose up to 32 selections for playback in the order you like.
(CD ) button.
The total number in memory will appear.
7
Press the
/
button to start playback.
23
03/12/19
CD-SW300 15-25.fm
CD or MP3/WMA disc Playback
CD-SW300
MP3/WMA navigation (only for MP3/WMA files)
MP3/WMA navigation:
You can search and play files by folder or title. For example, when
you assign three titles to a file, enter genre (such as jazz) as title 1,
album name as title 2, and music title as title 3 to search the file by
any title.
You can search and play files by folder or title 1/2/3 within one
MP3/WMA disc (see page 25).
By entering a name, you can search files by folder or title 1/2/3
within one MP3/WMA disc (see page 26).
Folders or titles can be programmed within one MP3/WMA disc
(see page 27).
When you enter file names on your PC, connect words with hyphens.
This product recognizes the first word as title 1, second one as title
2, and third one as title 3. Up to three words can be recognized.
Example:
Folder
Title 1
Title 2
Title 3
(File name)
Folder
Title 1
Title 2
Title 3
AAA
(POPULAR-HITS 1-A MUSIC.mp3)
(POPULAR-HITS 2-B MUSIC.mp3)
BBB
(JAZZ-HITS 1-A MUSIC.mp3)
(JAZZ-HITS 2-B MUSIC.mp3)
CCC
(ROCK-HITS 1-A MUSIC.mp3)
(ROCK-HITS 2-B MUSIC.mp3)
(ROCK-HITS 3-C MUSIC.mp3)
(ROCK-HITS 4-D MUSIC.mp3)
Notes:
MP3 files must have the extension ".mp3".
WMA files must have the extension ".wma".
Up to 100 folders or 300 files can be read on the unit. If either limit
is exceeded, no more folders/files are displayed.
This unit recognizes and displays up to 48 characters for folder
names, and up to 32 characters for title 1/2/3.
All file/folder names appear in uppercase.
24
03/12/19
CD-SW300 15-25.fm
CD-SW300
File search (by folder or title 1/2/3)
You can search and play files by folder or title 1/2/3 within one MP3/
WMA disc.
1
Press one of the
1 5 buttons to select a disc tray
containing an MP3/WMA disc.
2
Press the
disc.
3
Press the CD button to stop playback.
"NAVI READ" appears and the display shows the total number
of folders and files on the selected disc.
Use the
or
cursor button to scroll and select a folder
(or title), and then press the ENTER button.
Folder name
button, and the unit starts to read the MP3
If you press the / button instead of the ENTER button, all
files in the selected folder (or title) are played.
8
Use the
or
File name
MP3 indicator
WMA indicator
Total number Total number
of folders
of files
4
5
9
Press the NAVIGATION button.
Press the , ,
or
cursor button on the remote control to select
"FOL", "T-1", "T-2" or "T-3". To
search files by folder name, select
"FOL" (will flash).
Folder
Title 1
MP3
Title 2
Title 3
The following steps describe file search by folder:
6
Press the ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Folder name
The NAVIGATION button allows you to go one step back.
Press the DISPLAY button to
check the number of files.
cursor button to scroll and select a file.
Press the / button to start playback.
The unit plays from the selected file to the last file in the selected folder (or title), and the previous display returns.
File search by title 1/2/3:
In step 5, select "T-1", "T-2" or "T-3" and follow the same steps as
file search by folder.
The unit searches all files on the disc, regardless of the folder.
To stop playback:
Press the CD button.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
CD or MP3/WMA disc Playback
/
7
Notes:
In the MP3/WMA navigation mode, direct play and direct search
functions are disabled.
If a folder, title or file name does not appear, or appears incorrectly, remove and reinsert the disc and try again.
If you press the RANDOM button in the stop mode, the MP3/WMA
navigation mode will be canceled.
25
03/12/19
CD-SW300 15-25.fm
CD-SW300
MP3/WMA navigation (only for MP3/WMA files) (continued)
Character search (for folder or title 1/2/3)
CD or MP3/WMA disc Playback
By entering a name, you can search files by folder or title 1/2/3 within
one MP3/WMA disc.
1
Perform steps 1 - 3 in "File search (by folder or title 1/2/3)"
on page 25.
2
3
Press the NAVIGATION button.
4
Press the , ,
or
cursor
button on the remote control to
select "FOL", "T-1", "T-2" or "T-3".
To search files by folder name,
select "FOL" (will flash).
Folder
Title 1
Title 2
Title 3
6
9
or
or
Use the
(or title).
or
cursor button to scroll and select a folder
10 Press the
/ button to start playback.
All files in the selected folder (or title) are played, and the previous display returns.
Press the CHARACTER button for 2 seconds.
Press the
alphabet.
Press the
display.
When finished, press the ENTER button. The unit searches
for the same name within folders (or titles).
If the search word is not in the folder (or title) name, "NOT
FOUND" appears and the menu returns.
The display will be ready for editing characters.
1st row: String table
2nd row: Input editor (8 digits)
5
8
cursor button to select the desired
button to go to the next page of character
Press the CHARACTER button and the active character will
be entered in the 2nd row of the display.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
Notes:
The unit searches regardless of the case, and names found will
appear in uppercase.
Some symbols do not appear properly.
Character entry with direct buttons:
The direct buttons on the remote
control can also be used for character entry.
In step 5 on the left, use buttons 0 9 to enter alphabets.
Alphabet types change as you
press a button.
For example, press "2" four times to enter "C".
To delete an entered character, move the cursor to the character with the or button and press the CLEAR/DIMMER button on the remote control.
7
26
Repeat steps 5 and 6 to enter characters.
In the folder (or title) name search, you do not have to enter the
full name. The unit searches for names beginning with the entered characters.
2
A
B
C
Characters:
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO 7 PQRS 8 TUV 9 WXYZ
: indicates a space.
03/12/19
CD-SW300 26-33.fm
0
CD-SW300
1
Perform steps 1 - 3 in "File search (by folder or title 1/2/3)"
on page 25.
2
3
Press the NAVIGATION button.
4
Press the , , or cursor button on the remote control
to select "FOL", "T-1", "T-2" or "T-3" and then press the
ENTER button.
The total number of folders (or titles) appears for 2 seconds,
and names of the first 2 folders (or titles) are displayed.
Press the or cursor button to select the desired folder
(or title) and then press the MEMORY button.
The folder (or title) is memorized with all the files.
5
Repeat step 4 for other folders (or titles).
Up to 10 folders (or 10 titles) can be programmed.
6
Press the
/
button to start playback.
Programmed play will always start from the smallest folder (or
title) number.
To check, add or delete programmed contents:
In the stop mode, select a folder (or title) with the or cursor button. If the folder (or title) is programmed, "MEMORY" flashes.
Flashes if the folder (or title)
is programmed
When you press the MEMORY button with "MEMORY" flashing,
the folder (or title) is removed from the program.
If you press the MEMORY button with "MEMORY" off, the folder
(or title) is added to the program.
To clear all programs, press the CLEAR/DIMMER button in the
stop mode.
To exit the MP3/WMA navigation mode:
In the stop mode, press the CD button.
The programmed contents are cleared.
Notes:
The programmed contents are cleared when you eject a disc,
play another disc, switch the function, or enter the stand-by mode
with the ON/STAND-BY button.
If you press the RANDOM button in the stop mode, the MP3/
WMA navigation mode will be canceled.
If tracks are programmed using track numbers (see
"Programmed play" on page 23):
In the MP3/WMA navigation mode, only program by folder (or title)
name are played. When you exit the mode, the program by folder (or
title) name are cleared.
When you exit the MP3/WMA navigation mode, program by track
number are canceled.
(Program by track number are cleared when you remove the disc.)
CD or MP3/WMA disc Playback
Programmed play (for folder, title 1/2/3)
Folders or titles can be programmed within one MP3/WMA disc.
Folder, title 1, title 2 and title 3 cannot be programmed together simultaneously.
To stop playback:
Press the CD button.
The programmed contents are not cleared.
27
03/12/19
CD-SW300 26-33.fm
CD-SW300
Listening to the radio
Tuning
1
2
3
Press the ON/STAND-BY button to turn the power on.
Press the TUNER (BAND) button repeatedly to select the
desired frequency band (FM or AM).
Press the TUNING (
station.
or
) button to tune in to the desired
Radio
Manual tuning:
Press the TUNING (X or W) button as many times as required
to tune in to the desired station.
Auto tuning:
When the TUNING (X or W) button is pressed for more than
0.5 seconds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may stop automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING (W or X) button again.
Auto power on function:
When you press any of the following buttons, the unit turns on.
TUNER (BAND) button (main unit and remote control): The unit
turns on and the "TUNER" function is activated.
/
button on the main unit: The unit turns on and playback of
the last function starts (CD, TAPE, TUNER, GAME/VIDEO).
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.
" " will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button to
extinguish the "ST" indicator. The reception changes to monaural,
and the sound becomes clearer.
FM stereo mode indicator
FM stereo receiving indicator
28
03/12/19
CD-SW300 26-33.fm
CD-SW300
Memorizing a station
1
2
Perform steps 1 - 3 in "Tuning" on page 28.
3
Within 30 seconds, press the PRESET ( or ) button to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
4
Within 30 seconds, press the MEMORY button to store that
station in memory.
Press the MEMORY button to enter the preset tuning saving mode.
To recall a memorized station
Press the PRESET ( or
lect the desired station.
) button for less than 0.5 seconds to se-
To scan the preset stations
The stations saved in memory can be scanned automatically. (Preset memory scan)
1 Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
2 Press the PRESET ( or ) button again when the desired station is located.
Radio
You can store 40 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
If the "MEMORY" and preset number indicators go out before
the station is memorized, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a preset station.
When a new station is stored in memory, the station previously
memorized for that preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few hours
should there be a power failure or the AC power cord become disconnected.
To erase entire preset memory
1
2
Press the ON/STAND-BY button to enter the stand-by mode.
While pressing down the button and the
button, press
the TUNER (BAND) button until "TUNER CL" appears.
29
03/12/19
CD-SW300 26-33.fm
CD-SW300
Listening to a cassette tape (TAPE 1 or TAPE 2)
Tape Playback
Before playback:
For playback, use normal or low-noise tapes for
the best sound. (Metal or CrO tapes are not recommended.)
Do not use C-120 tapes or poor-quality tapes, as
they may cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack with a pen or a pencil.
Tape playback
1
2
Press the ON/STAND-BY button to turn the power on.
3
Load a cassette into the
TAPE 1 compartment or
TAPE 2 compartment with
the side to be played facing toward you.
4
Press the TAPE (1
want to listen to.
5
Press the / (TAPE
start playback.
Open the cassette compartment by pushing the
area marked " ".
2) button to select the cassette you
) to
Tape play indicator
Auto power on function:
When you press any of the following buttons, the unit turns on.
TAPE (1 2) button (main unit and remote control): The unit turns
on and the "TAPE" function is activated.
TAPE button (remote control): The unit turns on and the "TAPE"
function is activated.
/
button (main unit): The unit turns on and playback of the
last function starts (CD,TAPE,TUNER,GAME/VIDEO).
Auto power off function:
In the stop mode of tape operation, the main unit enters the stand-by
mode after 15 minutes of inactivity.
30
03/12/19
CD-SW300 26-33.fm
Recording on a cassette tape
Function
Main unit
Remote
control
Operation
Playback
Press in the stop
mode.
Stop
Press in the playback,
fast forward or rewind
mode.
Fast
forward/
Rewind
(TAPE 2
only)
Press in the playback
or stop mode.
Before recording:
When recording important selections, make a preliminary test to
ensure that the desired material is properly recorded.
SHARP is not liable for damage or loss of your recording arising
from malfunction of this unit.
The volume and sound controls can be adjusted with no effect
on the recorded signal (Variable Sound Monitor).
For recording, use only normal tapes. Do not use metal or
CrO tapes.
Erase-prevention tab of cassette tapes:
When recording on a cassette tape, make sure that the eraseprevention tabs are not removed. Cassettes have removable
tabs that prevent accidental recording or erasing.
To protect the recorded sound, remove the tab after recording.
Cover the tab hole with adhesive tape to record on the tape without the tab.
Caution:
To remove the cassette, press the (TAPE ) button, and then
open the compartment.
Before changing from one tape operation to another, press the
(TAPE ) button.
If a power failure occurs during tape operation, the tape head will
remain engaged with the tape and the cassette door will not open.
In this case, wait until the power is restored.
Side A
Tab for side B
Tape Recording
Various tape functions
CD-SW300
Tab for side A
31
03/12/19
CD-SW300 26-33.fm
CD-SW300
Recording on a cassette tape (continued)
Recording from a CD or MP3/WMA disc
1
2
3
4
Press the ON/STAND-BY button to turn the power on.
Press the CD button.
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
button.
Tape Recording
Recording will be paused.
5
6
Press one of the
1-
5 buttons to select the desired disc.
Within 5 seconds, press the
/
button to start recording.
Recording is started from the selected disc. When the playback of the last track is finished or the end of the tape is
reached, the disc and the cassette will stop automatically.
Playback of the disc will start approximately 7 seconds after
the tape starts.
To stop recording:
Press the (TAPE ) button.
The disc and tape will stop.
32
03/12/19
CD-SW300 26-33.fm
CD-SW300
To stop recording:
Press the (TAPE ) button.
The disc and tape will stop.
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
1
2
Recording from the radio
1
2
3
Load a prerecorded cassette
into the TAPE 1 cassette compartment. Insert a blank tape
into the TAPE 2 cassette compartment.
Tune in to the desired station (see page 28).
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
button.
TAPE 1
Press the
/
(TAPE
) button to start recording.
To interrupt recording:
Press the
button.
To resume recording, press the
/
(TAPE
) button.
3
Press the TAPE (1
the display.
4
Press the
button.
Recording will be paused.
5
Press the
/
2) button until "TAPE 1" appears on
(TAPE
) button to start dubbing.
To stop dubbing:
Press the (TAPE ) button.
TAPE 1 and TAPE 2 will stop simultaneously.
To stop recording:
Press the (TAPE ) button.
Erasing recorded tapes
1
Note:
If you hear a whistling noise while recording an AM station, move the
AM loop antenna.
TAPE 2
It is recommended that the recording tape is the same length as
the master tape.
Recording will be paused.
4
Press the ON/STAND-BY button to turn the power on.
Tape Recording
To perform programmed recording:
1 Program discs and tracks (see page 23).
2 Press the
button.
3 Press the / (TAPE ) button to start recording.
2
3
4
Load the tape to be erased into the TAPE 2 cassette compartment with the side to be erased facing toward you.
Press the TAPE (1 2) button until "TAPE 2" appears on the display.
Press the
button.
Press the / (TAPE ) button to start erasing.
Note:
Make sure that the TAPE 1 is not in use.
33
03/12/19
CD-SW300 26-33.fm
CD-SW300
Timer and sleep operation (Remote control only)
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at a
preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset
time.
This unit has 2 types of timer: ONCE TIMER and DAILY TIMER.
Advanced Features
Once timer:
Once timer play or once timer recording works for
one time only at a preset time.
For example, if you are away but want to record a program on a radio station.
Timer playback or timer recording
Before setting timer:
Daily timer:
Daily timer play or daily timer recording works at
the same preset time every day.
For example, set the timer as a wake-up call every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to record a radio program, and use
the daily timer to wake up.
1 Set the daily timer (pages 34 - 36).
2 Set the once timer (pages 34 - 36).
1 minute or more
Once timer
Daily timer
Start
Stop
Start
1 Check that the clock is set to the correct time (refer to page 16).
If it is not set, you cannot use the timer function.
2 For timer playback: Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the cassette compartment.
1
2
3
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select "ONCE" or "DAILY", and press the MEMORY button.
Stop
Note:
When set times for the daily timer and once timer overlap, the once
timer takes priority. Allow an interval of at least 1 minute between operations.
Set the clock to the correct time if "ONCE" or "DAILY" does not
appear.
Continued to the next page
34
03/12/19
CD-SW300 34-43.fm
4
Within 10 seconds, press the
or
button to select "ONCE SET" or "DAILY SET", and press the MEMORY
button.
5
Press the
or
button to select "PLAY" or
"REC", and press the MEMORY button.
White
Red
9
Switch input with the
or
button, and then
press the MEMORY button.
To select the timer playback source: CD, TUNER, TAPE 1 or
TAPE 2.
To select the timer recording source: TUNER.
When you select the tuner, select a station by pressing the
or
button, and then press the MEMORY button.
If a station has not been programmed, "NO PRESET" will be
displayed and timer setting will be canceled.
10 Adjust
The illustrations show the daily timer setting.
6
Press the
or
button to adjust the hour and
then press the MEMORY button.
the volume using the VOLUME control, and then
press the MEMORY button.
Do not turn the volume up too high.
11 Press the ON/STAND-BY button to enter the power standby mode.
The "TIMER" indicator lights up and the unit is ready for timer
playback or timer recording.
The illustrations show the timer playback setting in the daily timer mode.
7
Press the
or
button to adjust the minutes and
then press the MEMORY button.
8
Set the time to finish as in steps 6 and 7 above.
Advanced Features
CD-SW300
Continued to the next page
35
03/12/19
CD-SW300 34-43.fm
CD-SW300
Timer and sleep operation (Remote control only) (continued)
12 When the preset time is reached, playback or recording will
start.
The volume will increase gradually until it reaches the preset
volume.
Advanced Features
13 When the timer end time is reached, the system will enter
the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer will operate at the same time every day. It will continue until the daily timer setting is canceled. Cancel the daily timer when it is not in use.
Note:
When performing timer playback or recording using another unit connected to the GAME INPUT jacks, select "GAME" in step 9.
This unit will turn on or enter the power stand-by mode automatically,
however, the connected unit will not turn on or off.
Checking the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE CALL" or "DAILY CALL", and press the MEMORY button.
The unit returns to the timer stand-by mode after displaying the
settings in order.
Canceling the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE OFF" or "DAILY OFF", and press the MEMORY button.
Timer will be canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse the
same setting, perform the following operations.
1 Turn the power on and press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY button.
3 Within 10 seconds, press the
or
button to select
"ONCE ON" or "DAILY ON", and press the MEMORY button.
4 Press the ON/STAND-BY button to enter the power stand-by
mode.
Note:
The timer can also be set with the remote control.
36
03/12/19
CD-SW300 34-43.fm
CD-SW300
1
2
3
4
Play back the desired sound source.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
"SLEEP", and press the MEMORY button.
Press the
or
button to select the time.
(Maximum: 3 hours - Minimum: 1 minute)
3 hours - 5 minutes 5-minute intervals
5 minutes - 1 minute 1-minute intervals
5
Press the MEMORY button.
"SLEEP" will appear.
6
The unit will enter the power stand-by mode automatically
after the preset time has elapsed.
The volume will be turned down 1 minute before the sleep operation finishes.
To confirm the remaining sleep time:
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP X : XX".
"X : XX" is remaining sleep time.
The remaining sleep time is displayed for about 10 seconds.
You can change the remaining sleep time while it is displayed by
pressing the MEMORY button.
To cancel the sleep operation:
Press the ON/STAND-BY button while "SLEEP" is indicated.
To cancel the sleep operation without setting the unit to the stand-by
mode, proceed as follows.
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP OFF", and press the MEMORY button.
To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up
to CD in the next morning.
Sleep and timer recording:
For example, you can fall asleep listening to the CD and record radio
programs while sleeping.
1
2
Set the sleep time (see left, steps 1 - 5).
While the sleep timer is set, set the timer playback or recording
(steps 2 - 10, pages 34 - 35).
Sleep timer setting
Timer playback or
recording setting
1 minute - 3 hours
Sleep operation will
automatically stop.
Advanced Features
Sleep operation
The radio, CD, MP3/WMA disc and cassette tape can all be turned
off automatically.
End time
Desired time
Timer playback or recording
start time
Caution:
When using the cassette deck, be sure the tape length is long
enough to perform both functions. If you want to sleep and wake up
listening to a tape, and the length of the tape is shorter than the sleep
timer setting, timer playback or recording will not be possible.
37
03/12/19
CD-SW300 34-43.fm
CD-SW300
Enhancing your system
Listening to playback sounds of Game, VCR,
DVD, etc.
The connection cord is not included. Purchase a commercially available cord as shown below.
GAME or VCR, DVD, etc.
To the line output jacks
Advanced Features
Connect a video game system, VCR, DVD, etc. to the front
GAME INPUT (VIDEO, AUDIO L and R) jacks.
2
Connect a TV to the rear VIDEO OUT jacks.
Switch the TV input to auxiliary.
3
4
5
Yellow
White
1
Yellow White Red
Red
Press the ON/STAND-BY button to turn the power on.
Press the GAME/VIDEO button.
Play the connected equipment.
You can enjoy sounds from the supplied speakers and images
on the TV.
Note:
To prevent noise interference, place the unit away from the television.
Video cable
(not supplied)
RCA cord
(not supplied)
Auto power on function:
When you press any of the following buttons, the unit turns on.
GAME/VIDEO button (main unit and remote control): The unit
turns on and the "GAME" function is activated.
/ button on the main unit: The unit turns on and playback of
the last function starts (CD,TAPE,TUNER,GAME/VIDEO).
TV
To record on a tape from game, VCR, etc.
To video
input jack
Yellow
Video cable
(not supplied)
Yellow
AC INPUT
1
2
3
4
5
Insert a cassette in the TAPE 2 cassette compartment.
Press the GAME/VIDEO button.
Press the
Press the
button.
/
(TAPE
) button.
Start the game system, VCR, etc.
38
03/12/19
CD-SW300 34-43.fm
Troubleshooting chart
Before plugging in or unplugging the headphones, reduce the volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter plug and
impedance between 16 and 50 ohms. The recommended impedance is 32 ohms.
Plugging in the headphones disconnects the speakers automatically. Adjust the volume using the VOLUME control.
Many potential problems can be resolved by the owner without calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
General
Symptom
The clock is not set to the
correct time.
When a button is pressed,
the unit does not respond.
No sound is heard.
Possible cause
Did a power failure occur? Reset
the clock. (Refer to page 16.)
Set the unit to the power standby mode and then turn it back on.
If the unit still malfunctions, reset
it. (Refer to page 41.)
Is the volume level set to "0"?
Are the headphones connected?
Are the speaker wires disconnected?
CD player
Symptom
Playback does not start.
Playback stops in the middle or is not performed
properly.
Playback sounds are
skipped, or stopped in the
middle of a track.
References
Headphones
CD-SW300
Possible cause
Is the disc loaded upside down?
Does the disc satisfy the standards?
Is the disc distorted or
scratched?
Is the unit located near excessive
vibrations?
Is the disc very dirty?
Has condensation formed inside
the unit?
39
03/12/19
CD-SW300 34-43.fm
CD-SW300
Troubleshooting chart (continued)
Cassette deck
Symptom
Cannot record.
References
Cannot record tracks with
proper sound quality.
Cannot erase completely.
Sound skipping.
Cannot hear treble.
Sound fluctuation.
Cannot remove the tape.
Tuner
Possible cause
Is the erase-prevention tab removed?
Is it a normal tape? (You cannot
record on a metal or CrO tape.)
Is there any slack?
Is the tape stretched?
Are the capstans, pinch rollers,
or heads dirty?
If a power failure occurs during
playback, the heads remain engaged with the tape. Do not open
the compartment with great
force.
Symptom
The radio makes unusual
noises continuously.
Possible cause
Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop antenna placed properly? Move the
antenna away from the AC power cord if it's located nearby.
Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
Remote control
Symptom
The remote control does
not operate.
Possible cause
Is the AC power cord of the unit
plugged in?
Is the battery polarity correct?
Are the batteries dead?
Is the distance or angle incorrect?
Does the remote control sensor
receive strong light?
40
03/12/19
CD-SW300 34-43.fm
CD-SW300
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
Clearing all the memory (reset)
1
2
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the button and the button, press the
TUNER (BAND) button until "CLEAR ALL" appears.
Before transporting the unit
Remove all CDs from the unit. Make sure there is no CD in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the unit
with discs left inside can damage the unit.
Care of compact discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD collection and player.
Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
Keep your discs away from direct sunlight, heat, and excessive
moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
NO
YES
Correct
References
If trouble occurs
When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage
due to lightning, etc.) or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD program.
41
03/12/19
CD-SW300 34-43.fm
CD-SW300
Maintenance
Specifications
Cleaning the tape-handling parts
Dirty heads, capstans or pinch rollers can cause poor sound and
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
When cleaning the heads, pinch rollers, etc., unplug the unit
which contains high voltages.
A
TAPE 1
D
E
B
C
B
C
References
TAPE 2
Playback head
Capstan
Pinch roller
Erase head
Recording/Playback head
After long use, the deck's heads and capstans may become magnetized, causing poor sound. Demagnetize these parts once every 30 hours of playing/recording time by using a commercial tape
head demagnetizer. Read the demagnetizer's instructions carefully before use.
Cleaning the CD pickup lens
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be
some deviations from these values in individual units.
General
Power source
AC 120 V, 60 Hz
Power consumption P W
Dimensions
Width: 10-1/4" (260 mm)
Height: 13" (330 mm)
Depth: 12-7/8" (323 mm)
Weight
P lbs. (P kg)
Amplifier
Output power
Output terminals
In order to ensure proper operation of the CD player, preventative
maintenance (cleaning of the laser pickup lens) should be performed
periodically. Lens cleaners are commercially available. Contact your
local CD software dealer for options.
Cleaning the cabinet
Input terminals
Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth.
Caution:
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of the unit. It may cause malfunctions.
Front Speaker: 115 watts minimum RMS per
channel into 6 ohms from 100Hz to 20 KHz,
10% total harmonic distortion.
Subwoofer: 220 watts RMS into 12 ohms
from 50Hz to 120 Hz, 10% total harmonic
distortion.
Front Speakers: 6 ohms
Subwoofer: 12 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Video output: 1Vp-p
Game/ Auxiliary (audio signal):
500 mV/ 47 k ohms
Game/Video: 1Vp-p
42
03/12/19
CD-SW300 34-43.fm
CD-SW300
CD player
D/A converter
Frequency
response
Dynamic range
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser
pickup
1-bit D/A converter
20 - 20,000 Hz
90 dB (1 kHz)
Tuner
Frequency range
FM: 87.5 - 108.0 MHz
AM: 530 - 1,720 kHz
Type
3-way type speaker system
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
Super tweeter
2" (5 cm) tweeter
6-5/16" (16 cm) woofer
230 W
115 W
6 ohms
Width: 7-7/8" (200 mm)
Height: 13" (330 mm)
Depth: 9-1/8" (231 mm)
P lbs. (P kg) /each
Cassette deck
Frequency
response
Signal/noise ratio
Wow and flutter
50 - 14,000 Hz (normal tape)
Subwoofer
Type
55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/playback)
0.3 % (WRMS)
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
Full Range
8" (20 cm) subwoofer
440 W
References
Type
Signal readout
Front Speaker
220 W
12 ohms
Width: 9-13/16" (250 mm)
Height: 13" (330 mm)
Depth: 11-9/16" (294 mm)
13 lbs. (5.9 kg)
43
03/12/19
CD-SW300 34-43.fm
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
CD-SW300 Mini Component System
(Be sure to have this information available when you need service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
0311
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
03/11/4
CD-SW300_BACK.fm
Printed in Malaysia
TINSEA125AWZZ
06A R KI 1