20F630
CU20F630
1st Edition
SERVICE MANUAL
S52J320U-FS1/
COLOR TELEVISION
Chassis No. GA-2
MODELS
20F630
CU20F630
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 6
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 7
» SERVICE MODE ................................................................................................................................... 8
» ADJUSTMENT METHOD ................................................................................................................... 13
» CHASSIS LAYOUT ............................................................................................................................. 28
» BLOCK DIAGRAM .............................................................................................................................. 30
» DESCRIPTION OF SCHEMATIC DIAGRAM ...................................................................................... 40
» WAVEFORMS ..................................................................................................................................... 41
» SCHEMATIC DIAGRAMS ................................................................................................................... 42
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 52
» REPLACEMENT PARTS LIST ............................................................................................................ 55
» PACKING OF THE SET ...................................................................................................................... 62
ELECTRICAL SPECIFICATIONS
POWER INPUT ..................................................... AC 120 V, 60 Hz
POWER RATING .................................................................... 90W
PICTURE SIZE .......................................... 1,239 cm2 (192sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ................................................................................. Uni-Bi
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency ...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING ........................................ 2.5 W(RMS) x 2pcs
SHARP CORPORATION
SPEAKER
SIZE ................................................................... 5 x 12 cm, 2pcs
VOICE COIL IMPEDANCE ............................ 16 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ..................................................... 75 ohm Unbalanced
TUNING RANGES
VHF-Channels ............................................................... 2 thru 13
UHF-Channels ............................................................ 14 thru 69
CATV Channels ........................................................... 1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
20F630
CU20F630
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock hazards
when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
4A 125V
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
2
20F630
CU20F630
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
1.5k ohm
10W
0.15 F
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
20F630
CU20F630
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ë
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
LIMITES DES RADIATIONS X ET DE LA
HAUTE TENSION
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs
peuvent présenter un danger de choc électrique
lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur a deux systèmes de mise
à la terre qui sont séparés par un matériau isolant.
Le système de mise à la terre non-isolée (chaud) est
pour le circuit du régulateur de tension B+ et le circuit
de sortie horizontale. Le système de mise à la terre
isolé est pour les basses tensions C. C. B+ et le circuit
secondaire du transformateur de haute tension.
4A 125V
1. Tout le personnel réparateur doit être instruit des
instructions et procédés relatifs aux radiations X.
Le tube-image, seule source de rayons X dons les
téleviseurs transistorisés, n'émet pourtant pas de
rayons mesurables si la haute tension est maintenue
à un niveau préconisé dans la section "Vérification
de la haute tension".
C'est seulement quand la haute tension est excessive
que les rayons X peuvent entrer dans l'enveloppe du
tube-image y compris le conducteur de verre. Il est
important de maintenir la haute tension en-dessous
du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un
voltmètre à haute tension qui doit être périodiquement
étalonné.
3. La haute tension doit toujours être maintenue à la
valeur de régime-et pas plus haute. L'opération à des
tensions plus élevées peut entraîner une panne du
tube-image ou du circuit à haute tension et, dans
certaines conditions, peut entraîner une radiation
dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne
correctement, il n'y a aucun problème de radiation X.
Chaque fois qu'un châssis couleurs est réparé, la
luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
que la haute tension ne dépasse pas la valeur
spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures
d'essai sur un récepteur qui présente une haute
tension excessive, éviter de s'approcher inutilement
du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
que nécessaire pour localiser la cause de la tension
excessive.
P R E C AU T I O N : P O U R L A
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE 4A-125V.
REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme,
supprimer la charge statique en branchant
une résistance de 10 k en série avec un fil
isolé (comme une sonde d'essai) entre la
mise à la terre du tube-image et le fil
d'anodel. (Le corden d'alimentation doit être
retiré de la prise murale.)
1. Il est à noter que le tube-image de ce récepteur est
intégralement protégé contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.
4
20F630
CU20F630
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
» Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
arbres de commande et des boutons, écusson, etc.)
et mesurer la chute de tension CA en-travers de la
résistance.
Toutes les vérifications doivent être refaites après
avoir inversé la fiche du cordon d'alimentation. (Si
nécessaire, une prise d'adpatation non polarisée peut
être utilisée dans le but de terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme
les boutons de commande non-métalliques, les
isolants, le dos du coffret, les couvercles ou blindages
de réglage et de compartiment, les réseaux de
résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
» Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
» A l'aide de deux fils à pinces, brancher une résistance
de 1,5 k 10 watts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à
la terre.
» Utiliser un voltmètre CA d'une sensibilité d'au moins
5000 /V pour mesurer la chute de tension en travers
de la résistance.
Voltmètre CA
1.5k ohm
10W
0.15 F
SONDE D’ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentes
à vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
5
20F630
CU20F630
LOCATION OF USER'S CONTROL
Front Panel
VIDEO IN 2 L-AUDIO-R
POWER
Press → On.
Press again → Off.
SENSOR AREA FOR
REMOTE CONTROL
(INSIDE DOOR)
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
VOLUME UP/DOWN
(+) Increases sound.
( ) Decreases sound.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
Basic Remote Control Functions
POWER
Press → On.
Press again → Off.
REMOTE KEYPAD
Accesses any channel from keypad.
Infrared Transmitter Window
POWER
CATV
TV
DVD
VCR
DISPLAY
INPUT
1
2
3
4
5
6
7
8
9
FLASHBACK
Returns to previous channel.
PERSONAL PREFERENCE
With the Personal Preference buttons,
you can program your favorite programs
by using the 4 categories A, B, C and
D. The channels can be accessed
quickly by using these buttons.
0
100
PERSONAL PREFERENCE
A
VOLUME UP/DOWN
(+) Increases sound.
( ) Decreases sound.
In menu mode, changes or selects
the TV adjustments.
ENTER
FLASHBACK
B
C
D
CH
VOL
—
VOL
+
CH
MENU
MUTE
SKIP
VCR-CH
POWER (DVD/VCR)
PLAY
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
REC
REW
STOP
FWD
PAUSE
MUTE
Press → Mutes sound.
Press again → Restores sound.
CLOSED CAPTION appears when
sound is muted.
TV CATV VCR DVD
CATV/DVD-TV/VCR MODE buttons
Press TV/VCR, sends power and
channel select commands (Channel up/
down and Random Access buttons) to
the TV and VCR control.
Press CATV/DVD, sends power and
channel select commands to a cable
TV converter and DVD control.
DISPLAY
Press → Displays receiving channel for
four seconds.
Press again → Removes display.
Temporarily displays receiving channel
when in Closed Caption mode.
INPUT
Press → Switch to external video INPUT
1 mode or COMPONENT mode.
Press 2 times → Switch to external
video INPUT 2 mode.
Press 3 times → Switch back to the
original TV mode.
ENTER
Used in some instances where a Cable
Converter Box requires an enter
command after selecting channels,
when using the REMOTE KEYPAD
button.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
Moves the » mark of the MENU
screens.
POWER (DVD/VCR)
Press → On.
Press again → Off.
DVD/VCR CONTROL
REC
SKIP/VCR-CH
Note:
The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the
remote control, place it under a fluorescent light or other lighting.
The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
The degree of illumination will vary depending on the strength of lighting used.
The degree of illumination will decrease with time and depending on the temperature.
The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
Sunlight and fluorescent lighting are the most effective when charging the display.
6
20F630
CU20F630
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly tuned
in test signal.
3. Enter the service mode and set Y-mute ON by using
Service R/C.
4. The voltage should be approximately 28.6kV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for accurate
input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to P603 Pin3 and make
sure that the voltmeter reads 18.9 ±1.1V.
5. Apply external 24.5V DC at P603 Pin3 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord at least 4
second before plugging in again. Now make sure that
normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
7
20F630
CU20F630
SERVICE MODE
Service Mode Overview
1.
2.
3.
4.
Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.
Service mode is cleared by entering SERVICE key or CH-UP +VOL-DOWN key command during service mode.
If key input port (SERVICE) input is LOW, then it is in service mode.
During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE or CH-UP + VOLDOWN is disabled.
5. Service mode can be switched to 4 modes as follows by key input MENU;
Option mode
First mode of service mode when SERVICE key is
pressed.
Adjustment mode
Setting mode
First mode of service mode when local key
CH-UP + VOL-DOWN is pressed after MCU reset.
Check mode
6. AFT processing is disabled during service mode. PLL setting data is set to fo data.
7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively
in service mode. Energy Save is off.
8. Sleep timer, View timer and Off timer are inactivated in Service mode.
9. Sound is muting in service mode except at Adjustment Items V20, M01, M02, M03, M04, M05, and M06.
8
20F630
CU20F630
Adjustment Mode Items
No.
V01
V02
V03
V04
V05
V06
V07
V08
V09
V10
V11
V12
V13
Item Name
SUB-PICTURE
SUB-TINT
SUB-COLOR
SUB-BRIGHT
SUB-SHARP
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
PIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
IC
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
Register
CONTRAST
TINT
COLOR
BRIGHT
VIDEO-TONE
V-SHIFT
H-PHASE
RF-Delay
V-SIZE
VIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
Range
0~127
0~127
0~127
0~255
0~63
0~7
0~31
0~127
0~63
0~63
0~255
0~255
0~255
Default
127
64
64
128
32
4
16
127
32
32
127
127
127
V14
V15
V16
V17
V18
V19
V20
V21
M01
M02
M03
M04
M05
M06
R-DRIVE
B-DRIVE
SUB-COLOR(YUV)
SUB-TINT(YUV)
CC-POS
(Vertical mode)
SUB-VOL
H-VCO
MTS-ATT
MTS-VCO
MTS-FILTER
MTS-WIDEBAND
MTS-SPECTRAL
SUB-VOL
1 Chip
1 Chip
1 Chip
1 Chip
Micron
1 Chip
1 Chip
1 Chip
MTS
MTS
MTS
MTS
MTS
MTS
R-DRIVE
B-DRIVE
COLOR
BASEBAND-TINT
0~127
0~127
0~127
0~127
0~255
0, 1, 2
0~127
0~7
0~15
0~63
0~63
0~63
0~63
0~63
64
64
64
64
32
0
127
4
10
32
28
27
32
63
V-MUTE,SERVICE
A-ATT
H-VCO
ATT
VCO
FILTER
WIDEBAND
SPECTRAL
VOL
9
20F630
CU20F630
Ë SELF ADJUSTMENT
H-VCO
1.
2.
3.
4.
5.
6.
7.
When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.
H-FREE(1chip) is set to 1.
H-OUT is set by intelligent monitor output.
IM input is set as TIM input.
H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.
When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.
H-FREE(1chip), intelligent monitor output and IM input mode are recovered.
RF-AGC
1.
2.
3.
4.
When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.
AGC-OUT is set by intelligent monitor output.
IM input is set as AD input.
By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the
maximum setting value.
5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.
6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.
7. Intelligent monitor output and IM input mode are recovered.
PIF-VCO
1.
2.
3.
4.
5.
6.
7.
When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.
VIF-DEF(1chip) is set to 1.
AFC is set by intelligent monitor output.
IM input is set as AD input.
VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.
When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.
VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.
MTS-FILTER
Adjustment is performed in the center of the range when FILTER status is OK.
1. If data is changed from 0 to 63, point where NG → OK is A and point where OK → NG is B.
2. If data is changed from 63 to 0, point where NG → OK is C and point where OK → NG is D.
3. (A+B+C+D)/4 is the adjustment point.
10
20F630
CU20F630
Setting Mode Items
No.
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
F51
F52
F53
F54
Item Name
VideoTone-Gain (TV)
VideoTone-Gain (AV)
VideoTone-Gain(YUV)
ABCL
BS
ABCL-G
SHP-AV
SHP-YUV
RGB-CLIP
E-SAVE
FAO-VOL
PIF-G
Y-DELAY(TV)
Y-DELAY(AV)
Y-DELAY(YUV)
TINT-AV
COL-AV
R-DRI(R2)
R-DRI(R)
R-DRI(B)
B-DRI(R2)
B-DRI(R)
B-DRI(B)
V-FREE
GAMMA
TRAP(TV)
TRAP(AV)
H-FREE
1W(TV)
1W(AV)
YLPF
BS-D
BS-C
SL(TV)
SL(AV)
SL(YUV)
AFC2
VD(TV)
VD(AV)
AS(TV)
AS(AV)
AS(YUV)
FBP(TV)
FBP(AV)
FBP(YUV)
C.Clip Level
PSW
FAO-VOL
CP
CC LEVEL
OSD POS
OFFSET-ADJ-COL
OFFSET-ADJ-TINT
OFFSET-ADJ-TINT-YUV
IC
1chip
1chip
1chip
1chip
1chip
1chip
OFFSET
OFFSET
1chip
OFFSET
1chip
1chip
1chip
1chip
1chip
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
MTS
MTS
PLL
MICRON
MICRON
1 chip
1 chip
1 chip
Register
V-TONE
V-TONE
V-TONE
ABCL
BS-OFF
ABCL-G
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
ExtRGB-Clip
CONTRAST(OFFSET)
A-ATT
VIF-GAIN
Y-Delay
Y-Delay
Y-Delay
TINT(OFFSET)
COLOR(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
V-FREE
GAMMA
TRAP-FINE
TRAP-FINE
H-FREE
V.Window
V.Window
YSW-LPF
BS-DISCHARGE
BS-CHARGE
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
AFC2-G
Vsync-Det
Vsync-Det
Auto-Slice
Auto-Slice
Auto-Slice
FBP Vth
FBP Vth
FBP Vth
C.Clip Level
PSW
VOL
CP
COLOR
TINT
BASEBAND-TINT
11
Range
0/1
0/1
0/1
0/1
0/1
0/1
-16~+16
-16~+16
0/1
0~63
0~127
0~7
0~7
0~7
0~7
-32~+32
-32~+32
-32~+32
-32~+32
-32 ~+32
-32~+32
-32~+32
-32~+32
0/1
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0~3
0~3
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0~63
0/1
-32~32
-32~32
-32~32
Default
0
0
0
0
0
0
0
0
0
30
120
4
0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
60
0
0
0
0
0
0
20F630
CU20F630
Option Mode Items
No
O01
O02
O03
O04
O05
O06
O07
O08
O09
O10
O11
O12
O13
O14
O15
O16
O17
O18
O19
ITEM
DEM0
DOWNLOAD
V-CHIP
SPEAKER
FAO
P.PREF
UNIV+
VIEW TIMER
EZ-SETUP
PON-CH
FAV-COL
COMPONENT
AV
AV2
MTS
TONE-CTRL
AUTO-OFF
INIT-LANG
SETUP-FLAG
O20
FR.AV (Front,
Rear AV)
0
1
Without DEMO
With DEMO
Without V-CHIP OP
With V-CHIP OP
Without V-CHIP
With V-CHIP
Without SPEAKER
With SPEAKER
Without FAO
With FAO
Without P.PREF
With P.PREF
Without UNIV+
With INIV+
Without VIEW TIMER
With VIEW TIMER
EZ-SETUP
AUTO PRESET
Without POWER-ON
With POWER-ON
FAV-COL
COL-TEMP
Without COMPONENT With COMPONENT
Without AV
With AV
AV1 system
AV2 system
Without MTS
With MTS
Without S-ADJ
With S-ADJ
Without AUTO-OFF
With AUTO-OFF
ENGLISH
SPANISH
NO SETUP
AUTO SETUP
3: Display "FRONT A/V INPUTS" and
"REAR A/V INPUTS" in DEMO mode.
2: Display "FRONT A/V INPUTS" only in
DEMO mode.
1: Display "REAR A/V INPUTS" only in
DEMO mode.
0: No display of above lines in DEMO mode.
DEFAULT
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
Check Mode
Micron mask version, software version and ROM correction function status are displayed in check mode.
12
20F630
CU20F630
ADJUSTMENT METHOD
Caution: to get into the service mode, one of the ways is press direct key for service items. the other ways
is short the main chassis JA309 and JA402
There is three stage of Service Mode data
First stage data from V01 ~ M06
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F51
to go into third stage of service mode data, press MENU key
Third stage data from 001 ~ 020
Below is the contents of these data
First Stage
Data
V01
V02
V03
V04
V05
V06
V07
V08
V09
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
V21
M01
M02
M03
M04
M05
M06
Service Mode
SUB-PICTURE
SUB-TINT
SUB-COLOR
SUB-BRIGHT
SUB-SHARP
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
PIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
R-DRIVE
B-DRIVE
SUB-COLOR(YUV)
SUB-TINT(YUV)
CC-POS
SCREEN CUT OFF
SUB-VOL
H-VCO
MTS-ATT
MTS-VCO
MTS-FILTER
MTS-WIDEBAND
MTS-SPECTRAL
SUB-VOL
Function
CONTRAST
TINT
COLOR
BRIGHT
VIDEO-TONE
V-SHIFT
H-PHASE
RF-DELAY
V-SIZE
VIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
R-DRIVE
B-DRIVE
COLOR
BASEBAND-TINT
CC-POS
CUT OFF
A-ATT
H-VCO
ATT (MTS)
VCO (MTS)
FILTER (MTS)
WIDEBAND (MTS)
SPECTRAL (MTS)
VOL (MTS)
Auto Adjustment Item
1. H-VCO (Currently need manual adj)
2. RF-AGC
3. PIF-VCO
4. MTS-FILTER
13
Range
0~127
0~127
0~127
0~255
0~63
0~7
0~31
0~127
0~63
0~63
0~255
0~255
0~255
0~127
0~127
0~127
0~127
0~255
0~2
0~127
0~7
0~15
0~63
0~63
0~63
0~63
0~63
Default Data
127
64
64
128
32
7
16
127
32
32
64
64
64
64
64
64
64
32
0
127
4
10
32
28
27
32
63
20F630
CU20F630
Second Stage
Data
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
F51
F52
F53
F54
Service Mode
VIDEO TONE -GAIN (TV)
VIDEO TONE -GAIN (AV
VIDEO TONE -GAIN(YUV)
ABCL
BS
ABCL-G
SHP-AV
SHP-YUV
SHP-CLIP
E-SAVE
FAO-VOL
PIF-G
Y-DELAY(TV)
Y-DELAY(AV)
Y-DELAY(YUV)
TINT-AV
COL-AV
R-DRI(R2)
R-DRI( R)
R-DRI(B)
B-DRI(R2)
B-DRI( R)
B-DRI(B)
V-FREE
GAMMA
TRAP(TV)
TRAP(AV)
H-FREE
1W(TV)
1W(AV)
YLPF
BS-D
BS-C
SL(TV)
SL(AV)
SL(YUV)
AFC2
VD(TV)
VD(AV)
AS(TV)
AS(AV)
AS(YUV)
FBP(TV)
FBP(AV)
FBP(YUV)
C.CLIP LEVEL
PSW
FAO-VOL
CP
CC LEVEL
OSD POS
COL OFFSET
TINT OFFSET
TING-YUV
Function
V-TONE
V-TONE
V-TONE
ABCL
BS-OFF
ABCL-G
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
EXTRGB-CLIP
CONTRAST(OFFSET)
A-ATT
VIF-GAIN
Y-DELAY
Y-DELAY
Y-DELAY
TINT(OFFSET)
COLOR(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
V-FREE
GAMMA
TRAP-FINE
TRAP-FINE
H-FREE
V.WINDOW
V.WINDOW
YSW-LPF
BS-DISCHARGE
BS-CHARGE
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
AFC2-G
VSYNC-DET
VSYNC-DET
AUTO-SLICE
AUTO-SLICE
AUTO-SLICE
FBP VTH
FBP VTH
FBP VTH
C.CLIP LEVEL
PSW
VOL
CHARGE PUMP
CC LEVEL
OSD POS
(SUR → NOR)
(SUR → NOR)
TINT-YUV(OFFSET)
14
Range
0/1
0/1
0/1
0/1
0/1
0/1
-16~+16
-16~+16
0/1
0~63
0~127
0~7
0~7
0~7
0~7
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
0/1
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0~3
0~3
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0~63
0/1
0/1
0/1
-32~+32
-32~+32
-32~+32
Default Data
0
0
0
0
0
0
0
0
0
30
120
4
0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
60
0
0
0
0
0
0
20F630
CU20F630
Third Stage
Data
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
Service Mode
DEMO
DOWNLOAD
V-CHIP
SPEAKER
FAO
P.PREF
UNIV+
VIEW TIMER
EZ-SETUP
PON-CH
FAV-COL
COMPONENT
AV
AV2
MTS
TONE-CTRL
AUTO-OFF
INIT-LANG
SETUP-FLAG
AV-FR
DATA="0"
DATA="1"
DEMO OFF
ON
V-CHIP OP OFF
ON
V-CHIP OFF
ON
SPEAKER OFF
ON
FAO OFF
ON
P.REF OFF
ON
UNIV+ OFF
ON
VIEW TIMER OFF
ON
EZ-SETUP
AUTO PRESET
POWER-ON OFF
0N
FAV-COL
COL-TEMP
COMPONENT OFF
ON
AV OFF
ON
AV2 OFF
ON
MTS OFF
ON
S-ADJ OFF
ON
AUTO-OFF OFF
ON
ENGLISH
SPANISH
NO SET UP
AUTO SET UP
"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT
15
Default Data
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
ADJUSTMENT
PROCEDURE
16
001
002
1
0
1
0
1
1
1
1
FAO
1
1
DEF
20F630
CU20F630
FUNCTION
1
1
1
1
AV
1
1
MTS
1
1
16-1
019 → “0”=NO SET UP “1”=AUTO SETUP
0
0
0
0
TONE AUTO LAN
016 017 018
“1”=COL-TEMP
“1”=SPANISH
1
1
AV2
013 014 015
011 → ”0”=FAV-COL
018 → “0”=ENGLISH
1
1
COMP
FAV-COL
1
1
012
011
1
1
P.PREF UNIV+ VIEW
010
020
0
0
PON-CH
1
1
3
3
SETUP AV-FR
019
0
0
EZ
006 007 008 009
REFER AS BELOW
“0”=DISABLE “1”=ENABLE
009 → “0”=EZ-SETUP “1”=AUTO PRESET
1
1
SP
003 004 005
DEMO DOWNLOAD V-CHIP
BUS OPTION FOR THIRD STAGE SERVICE DATA
DEF
20F630
CU20F630
FUNCTION
BUS OPTION FOR THIRD STAGE SERVICE DATA
OSD CHECKING
OUTPUT
–
CONTENT
20F630, CU20F630
–
PRE-ADJUST
REQUIREMENT
INPUT
CONDITION
–
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
REFER AS BELOW
OPTION SET UP
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
–
–
–
STEP RANGE
REFER AS BELOW
V05
F13
F14
F16
F17
F30
F34
F38
F40 F49
50
50
5
5
2
2
-7
-7
4
4
1
1
1
1
1
1
1
1
F18 F19 F20 F21 F22 F23 F52 F53 F35 F41
DEF
F48
F54
+3
+3
-2
-2
16-2
-18
-18
-8
-8
+6 +10 +8
+6 +10 +8
1
1
1
1
58
58
-8
-8
R-D(R2) R-D(R) R-D(B) B-D(R2) B-D(R) B-D(B) C-OF TI-OF SL(AV) AS(AV) FAO-VOL TIN-YUV
20F630
+8
CU20F630 +8
FUNCTION
1
1
SHARP Y-DL(TV) Y-DL(AV) TINT-AV COL-AV 1W(AV) SL(TV) VD(TV) AS(TV) CP
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
DEF
20F630
CU20F630
FUNCTION
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
OSD CHECKING
20F630, CU20F630
REFER AS BELOW
OPTION SET UP
20F630
CU20F630
US 4 CH LION HEAD (MONOSCOPE)
AC 120V, US MAGNETIC FIELD
CONFIRMATION BY CRT SCREEN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, CRT-PURITY
PRE-ADJUST
REQUIREMENT
0-31
17
17-1
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL
A
B
1. ADJUST THE V07 BUS DATA TO HAVE A BALANCE POSITION TO
SPEC OF A=B.
2. IF CANNOT MAKE IT TO A=B, ADJ FROM THE BEST POINT SO THAT
B SLIDELY SMALLER THAN A
I2C BUS CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V07
H-POSITION
ADJUSTMENT
ITEM
US 4 CH LION HEAD
AC 120V
CONFIRMATION BY CRT SCREEN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, CRT PURITY, V-PHASE, +B ADJUST
PRE-ADJUST
REQUIREMENT
[CHECKING SPEC]
OVERSCAN 10 ± 2.5%
17-2
ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS
SPECIFIED BELOW.
CAUTION: - PLEASE AGING TV MORE THAN 10 MINUTES BEFORE
ADJUSTMENT.
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V09
V-SIZE
ADJUSTMENT
ITEM
20F630
CU20F630
US 4 CH LION HEAD (MONOSCOPE PATTERN)
120V, RF INPUT, ZERO MAGNETIC FIELD
CONFIRMATION ON CRT SCREEN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, CRT-PURITY
PRE-ADJUST
REQUIREMENT
0-7
18
18-1
[CHECKING CONFIRMATION]
ADJUST V06 BUS DATA TO HAVE MOST ACCEPTABLE VERTICAL POSITION.
THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL
POSITION
NOTE: THE DATA FOR V06 LIMIT AT <= 04, EVEN POSITION GOOD
ENOUGH
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V06
V-PHASE
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
STEP RANGE
0~255
18-2
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL
A
TEXT BOX BLK
B
1) BY SELECTING THE V18, BOX BLK TEXT WILL BE APPEARED.
2) ADJUST THE V18 BUS DATA TO HAVE A BALANCE POSITION TO
SPEC OF A=B.
CONFIRMATION ON CRT DISPLAY.
AC 120V
US 4 CH LION HEAD
OPTION SET UP, BUS SET UP
I2C CONTROL
V18
CLOSED CAPTION SET UP
20F630
CU20F630
NO SIGNAL (RASTER) CONDITION
AC 120V
IC 801 PIN 11 (MANUAL ADJ)
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
0-7
19
[CHECKING SPEC]
FREQ = 15.735 ± 0.2 KHz
19-1
(SELF ADJ)
1) GO TO SERVICE MODE, BY SELECTING THE SERVICE DATA V21
2) PRESS THE R/C TO OPERATE AUTO H-VCO, OSD APPEAR "OK" AT
SCREEN
3) IF APPEAR "NG" REPEAT STEP 2
1) GO TO SERVICE MODE,
2) GO TO SERVICE DATA V21, ADJ UNTIL FREQ AS BELOW
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V21
H-VCO
ADJUSTMENT
ITEM
NO SIGNAL (RASTER) CONDITION
AC 120V
CONFIRMATION ON CRT DISPLAY (AUTO), IC801 PIN 2 VOLTAGE (MANUAL).
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
19-2
[CHECKING SPEC]
2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5V)
(AT MANUAL ADJUSTMENT MODE)
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) ADJUST THE DATA UP/DOWN UNTIL IC801 PIN 2 VOLTAGE BECOME
AS SPECIFIED BELOW
(AT SELF ADJUSTMENT MODE)
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR “OK” AT
SCREEN
3) IF APPEAR “NG” PLS REPEAT STEP2
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V10
PIF-VCO
ADJUSTMENT
ITEM
20F630
CU20F630
TUNER AGC TERMINAL (TP 201) OR CRT DISPLAY CONFIRMATION
OUTPUT
ADJUSTMENT
PROCEDURE
INPUT
CONDITION
RF INPUT
FIELD STRENGTH 56dBµV (FIX)
INPUT
CONDITION
20
[CHECKING SPEC]
MAX - 0.1V dc
20-1
(AT MANUAL ADJUSTMENT MODE)
1. ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BECOME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE.
2. CHANGE THE ANTENNA INPUT SIGNAL TO 63-67 dBµV, AND MAKE
SURE THERE IS NO NOISE
3. CHANGE THE ANTENNA INPUT SIGNAL TO 90-95 dBµV TO BE SURE
THAT THERE IS NO CROSS MODULATION BEAT.
(AT SELF ADJUSTMENT MODE)
1. GO TO SERVICE MODE
2. GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC
KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN.
3. IF APPEAR NG PLS REPEAT STEP 2 AGAIN.
CONTENT
US10CH HALF COLOR BAR
CONTENT
ADJUSTMENT
PROCEDURE
OUTPUT
PRE-ADJUST
REQUIREMENT
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
I2C CONTROL
0-127
ADJUSTMENT
ITEM
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V08
RF-AGC
ADJUSTMENT
ITEM
STEP RANGE
0-255
20-2
[VOLTAGE CONFIRMATION]
1) IN SERVICE MODE, SET V04&V11&V12&V13 TO 127; V14&V15 TO
64, GET IN Y-MUTE BY R/C AND SET V19 TO “1”, PICTURE APPEAR
IN CUT-OFF CONDITION
2) ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW
BRIGHT, THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR
IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V11=RCUTOFF, V12=G-CUTOFF, V13=B-CUTOFF, FIX THE DATA OF THE
COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE
OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BECOME WHITE.
3) TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DISAPPEAR AND USE R/C TO SET V19 TO “0”, NEXT DISABLE THE YMUTE SO THAT PICTURE APPEAR IN NORMAL MODE.
CONFIRMATION ON CRT DISPLAY
120V
WINDOW PATTERN OR US4CH LION HEAD
OPTION SET UP, BUS SET UP
I2C CONTROL
V11,V12,V13
SCREEN
20F630
CU20F630
23CH 501RE WINDOW PATTERN
120V
CRT SCREEN DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN
PRE-ADJUST
REQUIREMENT
0-127, 0~255
21
21-1
[CHECKING CONFIRMATION]
X=0.273, Y=0.280 (11,600°K + 1 MPCD)
WHITE
US14
BLACK
1) WHITE (HIGH BEAM)
FIRST LET THE GUM POINT AT BLACK POSITION (AS DRAWING
ATTACH), ADJ V04 UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN
LET THE GUN POINT AT WHITE POSITION (AS DRAWING ATTACH),
ADJUST V01 UNTIL BRIGHTNESS Y BECOME 150 cd/m2, ADJUST
THE BUS DATA OF V14 (R DRIVE), V15(B DRIVE) UNTIL THE AXIS
OF COLOR TEMPERATURE BECOME X=0.273, Y=0.280
2) BLACK (LOW BEAM)
LET THE GUN POINT AT BLACK POSITION, IF THE VALUE SHIFTED
AWAY FROM THE DATA ADJUSTED IN STEP 1), ADJUST AGAIN THE
TWO SERVICE DATA WHICH HAVE CHOSEN AT SCREEN ADJUST
SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE.
*WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING
THIS ADJUSTMENT.
**REPEAT STEP 1), 2) TO GET A REGULATED POSITION.
I2C BUS CONTROL
STEP RANGE
WHITE BALANCE
CONTROL
ADJUSTMENT
V14,V15,V11,V12,V13
POSITION
ADJUSTMENT
ITEM
WINDOW PATTERN
120V
CRT SCREEN DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE
PRE-ADJUST
REQUIREMENT
US14
21-2
[VOLTAGE CONFIRMATION]
BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
BLACK
1) LET THE GUN POINT AT BLACK POSITION (AS ATTACH DRAWING),
ADJUST V04 BUS DATA UNTIL BRIGHTNESS Y=0.5 cd/m2, THEN
STEP DOWN MORE 4 STEP
I2C CONTROL
0-255
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V04
SUB-BRIGHT
ADJUSTMENT
ITEM
20F630
CU20F630
WINDOW PATTERN
120V
CRT SCREEN DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS
PRE-ADJUST
REQUIREMENT
22
22-1
[VOLTAGER CONFIRMATION]
BRIGHTNESS Y=150 cd/m2
WHITE
US14
1) LET THE GUN POINT AT WHITE POSITION (AS ATTACH DRAWING),
ADJUST V01 BUS DATA UNTIL BRIGHTNESS Y=150 cd/m2.
NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN’T MATCH
THE SPEC
I2C BUS CONTROL
0-127
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V01
SUB-PICTURE
ADJUSTMENT
ITEM
US 10 CH HALF COLOR BAR PATTERN
120V
B-AMP TR BASE (TP853)
CONFIRM WITH OSCILLOSCOPE
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST
REQUIREMENT
0-127
[CONFIRMATION]
22-2
B-AMP BASE (TP853)
MUST BE IN STEPPING
LEVEL
1) GET IN Y-MUTE FUNCTION BY R/C.
2) ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW.
3) DISABLE THE Y-MUTE
**PLS TAKE NOTE THAT SERVICE MODE DATA F53 NEED TO SET +8
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V02
SUB-TINT
ADJUSTMENT
ITEM
20F630
CU20F630
ADJUSTMENT
PROCEDURE
23
Y
23-1
[CHECKING CONFIRMATION]
W
G
100% WHITE
Cy
Mg
R
B
1) SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW
2) THIS WAVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS
OF COLOR BAR BEAT AT THE SAME LEVEL
**PLEASE TAKE NOTE THAT SERVICE DATA F52 MUST SET TO +10
ADJUSTMENT
PROCEDURE
–
24.5V
18.9± 1.1V DC
23-2
OPERATION VOLTAGE
TP VOLTAGE
[VOLTAGE CONFIRMATION]
[CAUTION]
FROM THE RECOVER CONFIRMATION MENTIONED ABOVE, THE AC
CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUGGING IN AGAIN.(IN ORDER TO MAKE SURE THE µ-COM HAS BEEN
RESET.)
[RECOVER INFORMATION]
PULL OUT THE AC CORD.
[OPERATION CONFIRMATION]
SUPPLY THE DC VOLTAGE TO P603 PIN 3 AND MAKE SURE THE PROTECTOR IS FUNCTIONED.
HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.
[VOLTAGE CONFIRMATION]
CHECK THE VOLTAGE OF P603 PIN 3 AS SPECIFIED BELOW.
SET THE USER CONTROL TO SHIPMENT POSITION.
CONFIRMATION BY THE CRT
OUTPUT
R-AMP TR BASE (TP851)
CONFIRM WITH OSCILLOSCOPE
OUTPUT
AC 120V, RF INPUT
INPUT
CONDITION
120V
INPUT
CONDITION
US 4 CH LION HEAD (MONOSCOPE PATTERN)
–
STEP RANGE
CONTENT
US 10 CH HALF COLOR BAR PATTERN
CONTENT
–
X-RAY PROTECTION OPERATING CONFIRMATION
AFTER ALL ADJUSTMENT FINISHED.
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TINT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
PRE-ADJUST
REQUIREMENT
I2C BUS CONTROL
0-127
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V03
SUB-COLOR
ADJUSTMENT
ITEM
20F630
CU20F630
AC 130V, RF INPUT
CRT ANODE VOLTAGE
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
–
24
24-1
[CAUTION POINT]
USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL/
DHHS STANDARD TO MAKE CORRECTION AND CONTROL.
BELOW 30kV
HIGH VOLTAGE
SET THE USER CONTROL TO SHIPMENT SETTING POSITION. PUSH
ON Y-MUTE BY R/C CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH
VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW.
AFTER ALL ADJUSTMENT FINISHED.
–
PRE-ADJUST
REQUIREMENT
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
–
HIGH VOLTAGE
ADJUSTMENT
ITEM
AC 120V, RF INPUT
CONFIRMATION BY THE CRT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
UHF 15 CH (V-CHIP TRANSMISION SIGNAL CH)
CONTENT
–
24-2
[VOLTAGE CONFIRMATION]
V-CHIP RATING DISPLAY IS EQUAVALENCE TO TRANSMISSION
RATING.
1) RECEIVE THE UHF 15 CH.
2) PUSH THE DISPLAY KEY (R/C), MAKE SURE THAT THE OSD
AFTER ALL ADJUSTMENT FINISHED.
–
PRE-ADJUST
REQUIREMENT
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
–
V-CHIP
ADJUSTMENT
ITEM
20F630
CU20F630
AC 120V, RF INPUT
CONFIRMATION BY CRT SCREEN
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
RATING SYS. DOWNLOAD SIGNAL A/B (PRCC SIG) INCLUDED SIGNAL.
CONTENT
25
[COMFIRMATION]
25-1
~ Do check one sample that been picked up for presenting the specified
group sample.
(UPLOADING CONFIRMATION)
1) RECEIVE THE DOWNLOAD B SIGNAL.
2) UNPLUG THE AC CORD AND PLUG IT AGAIN.
3) BACK TO V-CHIP CONTROL MENU, CHECK THE DOWNLOADED
RATING AND NAME.
(DOWNLOADING CONFIRMATION)
1) RECEIVE THE DOWNLOAD A SIGNAL.
2) SELECT V-CHIP CONTROL MENU THEN ON THE DOWNLOAD.
3) UNPLUG THE AC THEN PLUG AGAIN.
4) BACK TO V-CHIP CONTROL MENU, CHECK THE DOWNLOADED
RATIING AND NAME.
AFTER ALL ADJUSTMENT FINISHED.
–
–
PRE-ADJUST
REQUIREMENT
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
–
TRI-VISION
ADJUSTMENT
ITEM
NO SIGNAL SIGNAL (400HZ 100% MODULATION)
AC 120V, RF INPUT
IC 3001 39 PIN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST
REQUIREMENT
0~15
25-2
[CHECKING SPEC]
490 ± 10mVrms (CHECKING SPEC :490 ± 20mVrms)
1) SET THE SOUND VOLUME CONTROL MORE THAN 1.
2) ADJUST BUS DATA OF M01 UNTIL THE VOLTAGE OF 39 PIN BECOME AS SPECIFIED BELOW.
I2C BUS CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
M01
MS LEVEL ADJUSTMENT
ADJUSTMENT
ITEM
20F630
CU20F630
SIGNAL WITHOUT NOISE (SIGNAL WITHOUT SOUND MODULATION)
AC 120V
IC 3001 39 PIN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST
REQUIREMENT
26
26-1
[CHECKING SPEC]
62.94 ± 0.75kHz (CHECKING SPEC : 62.94 ± 1.20kHz)
1) CONNECT 100 µ F ELECTROLLYTIC CAPACITOR BETWEEN C3005
(-ve)-GND
2) ADJUST THE BUS DATA M02 UNTIL THE OUTPUT FREQUENCY OF
39 PIN BECOME AS SPECIFIED BELOW.
NOTE: TO MINIMIZE THE PRODUCTION TIME, ITEM 1) CAN IGNORE.
IF ITEM 2) CAN'T BE ADJUST, THEN ITEM 1) IS REQUIRE.
I2C BUS CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
M02
MTS+VCO ADJUSTMENT
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
STEP RANGE
0~63
26-2
[CHECKING SPEC]
REFER TO ABOVE (CHECKING SPEC : ± 2 STEP TO CENTRE)
1) ADJUST M03 DATA UNITILL OK DISPLAY ON SCREEN ADJUST THE
BUS DATA IN CENTRE OF THE RANGE.
CONFIRM BY CRT SCREEN
PIN 14 (FROM C3005 - TERMINAL)
SINE WAVE (9.4kHz, 600mVrms)
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO
I2C BUS CONTROL
M03
FILTER ADJUSTMENT
20F630
CU20F630
STEREO SIGNAL SIGNAL 1,: MODULATION 30%, L-CH ONLY, NR-ON, 300Hz
SIGNAL 2,: MODULATION 30%, L-CH ONLY, NR-ON, 3kHz
RF INPUT
IC 3001 39 PIN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO, FILTER
PRE-ADJUST
REQUIREMENT
27
27-1
[CHECKING SPEC]
OVER 25 dB (CHECKING SPEC : OVER 20 dB)
SET THE SOUND VOLUME TO MAXIMUM THEN MAKE SURE THE
READING FROM THE SPEAKER TERMINAL MUST BE OVER THE SPEC
AS SPECIFIED BELOW.
1) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNIT THE OF 39 PIN
BECOME MINIMUM LEVEL.
2) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNIT THE AC VOLTAGE OF 39 PIN BECOME MINIMUM LEVEL.
3) REPEAT STEP 1) AND 2).
I2C BUS CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
M04, M05
SEPARATION ADJUSTMENT
ADJUSTMENT
ITEM
27-2
20F630
CU20F630
20F630
CU20F630
MODEL 20F630 CHASSIS LAYOUT
28
20F630
CU20F630
MODEL CU20F630 CHASSIS LAYOUT
29
20F630
CU20F630
MODEL 20F630 BLOCK DIAGRAM: MAIN Unit
30
20F630
CU20F630
31
20F630
CU20F630
MODEL CU20F630 BLOCK DIAGRAM: MAIN Unit
32
20F630
CU20F630
33
20F630
CU20F630
MODEL 20F630 BLOCK DIAGRAM: CRT Unit
34
20F630
CU20F630
MODEL CU20F630 BLOCK DIAGRAM: CRT Unit
35
20F630
CU20F630
MODEL 20F630 BLOCK DIAGRAM: MTS MODULE Unit
36
20F630
CU20F630
37
20F630
CU20F630
MODEL 20F630 BLOCK DIAGRAM: MTS MODULE Unit
38
20F630
CU20F630
39
20F630
CU20F630
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTES:
WAVEFORM MEASUREMENT CONDITIONS:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
å
ç
AND SHADED (
) COMPONENTS
= SAFETY RELATED PARTS.
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES åET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE ç : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
40
20F630
CU20F630
WAVEFORMS
1 1.024 Vp-p
2 5.69 Vp-p
3 5.69 Vp-p
4 5.84 Vp-p
5 2.00 Vp-p
6 2.08 Vp-p
Horiz.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Vert.Rate
Vert.Rate
7 6.56 Vp-p
8 6.40 Vp-p
9 4.88 Vp-p
0 158 Vp-p
q 1140 Vp-p
Horiz.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Vert.Rate
e 3.8 Vp-p
r 118 Vp-p
t 440 Vp-p
y 5.04 Vp-p
u 5.12 Vp-p
i 112.8 Vp-p
Vert.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Vert.Rate
Horiz.Rate
o 94.4 Vp-p
p 109.6 Vp-p
Horiz.Rate
Horiz.Rate
41
w 48 Vp-p
20F630
CU20F630
MODEL 20F630 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
1
2
3
4
5
6
42
7
8
9
10
20F630
CU20F630
10
11
12
13
14
15
43
16
17
18
19
20F630
CU20F630
MODEL CU20F630 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
1
2
3
4
5
6
44
7
8
9
10
20F630
CU20F630
10
11
12
13
14
15
45
16
17
18
19
20F630
CU20F630
MODEL 20F630 SCHEMATIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
1
2
3
4
46
5
6
20F630
CU20F630
MODEL CU20F630 SCHEMATIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
1
2
3
4
47
5
6
20F630
CU20F630
MODEL 20F630 SCHEMATIC DIAGRAM: MTS MODULE Unit
H
G
F
E
D
C
B
A
1
2
3
4
5
6
48
7
8
9
10
20F630
CU20F630
10
11
12
13
14
15
49
16
17
18
19
20F630
CU20F630
MODEL CU20F630 SCHEMATIC DIAGRAM: MTS MODULE Unit
H
G
F
E
D
C
B
A
1
2
3
4
5
6
50
7
8
9
10
20F630
CU20F630
10
11
12
13
14
15
51
16
17
18
19
20F630
CU20F630
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
1
2
3
4
52
5
6
1
2
53
3
4
5
6
A
PWB-A: MAIN Unit (Chip Parts Side)
B2
F DC2
B
RJ 7 1
RJ 7 0
Z2
A2
R3 8 2
R3 1 3
R3 8 1
RJ 4 8
R3 1 7
RJ 6 3
D5 0 1
R3 1 5
R1 0 2 4
R8 0 1
R3 1 4
RJ 2 3
RJ 1 5
C3 1 3
R3 2 1
C3 1 9
R3 1 2
R2 0 5
C8 0 6
C7 5 9
RJ 1 1
R3 8 4
RJ 3 0
R3 8 3
RJ 0
R3
11
0
R3 0 8
RJ 2 2
R7 6 8
R1 0 5 9
RJ 6 0
C3 2 0
RJ 2 1
RJ 5 9
C3 0 8
R4 3 1
R3 0 7
R7 4 3
R1 0 3 8
C2 1 1
R2 1 1
R2 0 6
RJ 3
R1 0 2 1
C2 1 0
C2 1 2
D8 1 5
R8 3 0
R8 2 9
R8 3 3
R8 0 4
R1 8 5 1
R8 3 4
RJ 4 2
R1 8 5 2
C1 0 1 5
R1 0 7 0
R8 0 6
R1 8 5 3
R1 0 6 8
R3 1 6
R8 2 5
R3 0 5
RJ 1 4
R1 0 6 9
R4 3 4
R1 8 6 1
R1 8 5 0
C8 1 1
C8 1 2
R1 0 6 7
C8 1 3
R1 0 6 6
R1 0 3 3
Q8 0 5
R3 0 6
C8 4
R8
34
0
R8 3
C8
42
5
RJ 7 7
R1 8 6 2
R8 3 1
R8 3 8
R8 0 7
R8 2 8
Q3 0 1
C2 0 3
C2 0 5
C8 4 6
D8 1 0
R1 0 3 2
R8 0 5
R1 0 7 5
R1 0 3 6
R1 0 3 7
R7 4 4
R1 0 6 4
RJ 7
R1 0 2 2
C8 0 2
D8 1 3
C8 0 9
R1 0 3 1
C8 1 0
R1 0 3 4
D1 0 0 4
R4 3 2
D1 0 9 0
RJ 7 6
RJ 9
RJ 8
R3 1 0
Q3 0 2
RJ 6 9
R2 1 3
C8 0 4
R1 0 3 9
R8 4 0
Q7 4 0
Q7 4 1
R1 0 7 3
D1 0 8 8
R1 0 6 5
RJ 3 3
R1 0 7 1
I C8 0 1
D8 1 2
R3 0 3
C1 0 0 4
I C1 0 0 3
R1 0 7 4
RJ 3 5
R1 0 7 2
R8 0 3
C8 0 8
D8 1 4
D8 1 1
C8 3 6
Q7 5 5
Q1 0 0 1
R8 0 2
R8 3 5
C8 4 5
C8 4 4
C8 4 1
C8 4 7
C8 4 0
RJ 1 3
R7 6 6
R8 4 3
RJ 6 2
R8 3 9
R2 1 2
D2 0 2
Q2 0 2
C2 0 8
R2 2 0
R2 0 7
C8 3 9
F DC4
RJ 5 3
C1 8 6 4
C1 8 6 3
C1 8 6 2
C1 8 6 1
R8 1 0
R1 0 7 6
R4 3 5
R4 3 3
R3 1 8
R1 0 2 5
C2 1 3
R2
RJ120
RJ 2 6
C2 0 7
R2 0 9
C2 0 9
R2 0 8
Q2 0 1
R2 0 1
R2 0 2
C
C1 8 5 6
C8 1 4
RJ 6 4
RJ 2 4
C8 1 6
R8 4 2
F DC3
R1 0 6 2
R1 0 6 0
R1 0 4 9
R1 0 4 8
R1 0 4 6
R1 0 5 1
RJ 1 7
R1 0 5 3
RJ 6 1
R4
2
R3 6 5
R3 6 4
R1 0 6 1
RJ 7 4
R1 0 0 2
R1 8 5 4
C8 1 5
C1 8 5 5
R1 0 4 7
R1 0 4 3
R4 5 4
R1 0 5 2
D1 0 8 5
C1 0 0 9
C1 0 1 0
C1 0 1 1
R1 0 5 4
R3 6 2
R8 1 4
C1 0 0 8
D1 0 8 7
C8 2 3
RJ 3 7
C8 2 1
R8 3 2
R8 1 9
C1 0 1 3
R4 6 1
D1 0 8 6
Q8 0 3
C8 1 9
RJ 1 6
I C1 0 0 1
R1 0 6 3
R8 1 3
R8 1 1
R8 1 2
R8 2 7
R1
RJ82459
R3 6 3
D
R8 2 1
RJ 3 6
R1 0 5 7
R1 0 5 5
RJ 3 9
RJ 4 4
R8 1 6
Q8 0 4
Q1 0 0 2
R1 0 5 6
R8 2 2
C8 3 1
R8 2 0
C8 3 3
I C4 0 1
RJ 7 3
R4 3 7
RJ 4 7
R8 1 5
RJ 1 9
C4 3 6
R8 1 7
R4 5 8
R1 0 0 9
R1 0 0 3
RJ 3 2
R6 6 2
R6 6 1
R1 0 0 8
R1 0 0 7
Q6 0 4
RJ 6 5
R1 0 8 1
RJ 7 5
R5 2 2
R1 0 0 6
RJ 1
R5 2 1
C5 1 8
RJ 3 8
RJ 1 2
C5 1 9
R1 0 2 6
R6 1 9
C7 3 5
R5 1 6
RJ 5 0
R5 2 0
C5 1 7
R6 2 0
R5 0 4
E
RJ 4 9
RJ 5 1
RJ 3 4
R6 1 7
RJ 4 0
R5 2 7
R5 2 8
R1 0 2 7
RJ 7 2
RJ 5 2
R6 1 8
R6 1 3
RJ 4 1
RJ 4 6
R6 5 4
RJ 4 3
RJ 4 5
F
R7 1 4
C7 8 4
B1
F DC1
Z1
A1
G
H
20F630
CU20F630
20F630
CU20F630
H
G
F
PWB-B: CRT Unit (Wiring Side)
E
D
PWB-E: MTS MODULE Unit (Wiring Side)
C
R3 0 2 4
R3 0 2 5
RJ 1 0
R3 0 8 0
RJ 4
R3 0 8 1
Q3 0 0 7
R3 0 1 6
R3 0 0 4
R3 0 0 3
C3 0 0 2
I C3 0 0 2
R3 0 0 5
C3 0 0 8
R3 0 8 5
RJ 1 3
R3 0 8 4
C3 0 8 2
R3
03
RJ
76
RJ 2
B
Q3 0 0 6
RJ 6
I C3 0 0 1
R3 0 0 7
R3 0 1 9
R3 0 0 8
R3 0 8 2
RJ 1 4
R3 0 0 1
R3 0 0 2
RJ 3
R3 0 1 0
C3 0 1 3
R3 0 1 8
R3 0 8 3
R3 0 2 6
C3 0 3 1
R3 0 2 9
C3 0 3 2
C3 0 2 6
Q3 0 0 4
C3 0 2 8
C3 0 4 3
R3 0 1 1
Q3 0 0 1
R3 0 2 7
R3 0 3 4
C3 0 2 3
R3 0 1 3
R3 0 3 5
C3 0 3 5
C3 0 3 6
C3 0 2 4
C3 0 2 7
C3 0 2 5
R3 0 1 2
C3 0 3 3
Q3 0 0 2
R3 0 3 0
R3 0 2 8
C3 0 4 2
R3 0 2 1
Q3 0 0 5
R3
RJ
03
83
R3 0 3 2
R3 0 1 4
RJ 9
R3 0 3 1
RJ 1 5
RJ 1 7
RJ 1 6
A
PWB-E: MTS MODULE Unit (Chip Parts Side)
1
2
3
4
54
5
6
20F630
CU20F630
Ref. No.
★
Part No.
Description
Code
Ref. No.
PARTS LIST
★
Part No.
Description
Code
LISTE DES PIECES
PARTS REPLACEMENT
CHANGE DES PIECES
Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are
identified by å and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. The use of a substitute replacement part which
does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create
shock, fire or other hazards.
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp
éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces
élelectriques qui pr élesentent ces particularit éles, sont rep éler élee
par la marque å et sont hachur élees dans les listes de pi`eces et dans
les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente
pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece
recommand élee parl'usine et dans ce manuel de service, peut provoquer
une éLelectrocution, un incendie ou toutautre sinistre.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER
3. PART NO.
in USA:
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
2. REF. NO.
4. DESCRIPTION
1. NUMERO DU MODELE
2. NO. DE REF
3. NO. DE PIECE
4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
Contact your nearest SHARP Parts Distributor to order. For
location of SHARP Parts Distributor, Please call Toll-Free; 1800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
'
Ref. No.
★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE
MARK: X-RAY RELATED PARTS
Part No.
★
Description
'
MARQUE: PIECES RELATIVE AUX RAYONS X
Ref. No.
Code
L706
Description
Code
DUNTKB989WEA0(20F630)
DUNTKB989WEA1(CU20F630)
PWB-A MAIN UNIT
PICTURE TUBE
å
å
★
Part No.
VB51QDX992X2E X Picture Tube
RCiLGA032WJZZ X Degaussing Coil
QEARCA012WJZZ X Ground-Part
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å TU201 RTUNQA003WJZZ X Tuner
INTEGRATED CIRCUIT
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
20F630
PWB-A DUNTKB989WEA0 – MAIN Unit
PWB-B DUNTKA599WEB4 – CRT Unit
PWB-E DUNTKB271FMA3 – MTS MODULE Unit
—
—
—
IC301
IC401
å IC501
IC601
å IC701
å IC703
IC801
IC1001
IC1003
IC1003
VHiAN7522++-1
VHiMM1501XN-1∗
VHiTDA9302H-1
VHiKA7809AP-1
VHiTEA1507/-1
VHiSE130N//-1
VHiM61251AF1EQ
RH-iXA155WJN4
VHiBR2416E2-1∗
VHiCAT24W04-2∗
Q201
Q302
Q601
Q602
Q603
Q604
å Q701
Q703
Q740
Q741
Q751
Q752
Q753
Q755
Q804
Q805
Q1001
VS2SC2735//1E∗
VS2SD601AR/-1∗
VS2SC2482//-1+
VS2SD2539//1E
VS2SC3198-G-1+
VS2SD601AR/-1∗
VSSTP6NC80Z1E
VS2SC3198-Y-1+
VS2SD601AR/-1∗
VS2SD601AR/-1∗
VS2SC2236Y/-1+
VS2SC2236Y/-1+
VS2SC3198-G-1+
VS2SD601AR/-1∗
VS2SB709AR/-1∗
VS2SD601AR/-1∗
VS2SD601AR/-1∗
D201
D203
D393
D501
RH-EX0676GEZZ∗
RH-DX0048GEZZ∗
RH-DX0247CEZZ∗
RH-EX1393CEZZ∗
CU20F630
PWB-A DUNTKB989WEA1 – MAIN Unit
PWB-B DUNTKA599WEB5 – CRT Unit
PWB-E DUNTKB271WEA3 – MTS MODULE Unit
X
X
X
X
X
X
X
X
X
X
AN7522
MM1501XNRE
TDA9302H
KIA7809API
TEA1507P/N1
SE130N
I.C.
I.C.
BR24C16F(20F630)
I.C.(CU20F630)
AE
AF
AD
TRANSISTORS
—
—
—
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
2SC2735
2SD601AR
2SC2482
2SD2539
2SC3198-G
2SD601AR
STP6NC80Z
2SC3198-Y
2SD601AR
2SD601AR
2SC2236Y
2SC2236Y
2SC3198-G
2SD601AR
2SB709AR
2SD601AR
2SD601AR
AB
AA
AB
AB
AA
AA
AA
AB
AA
AA
AA
AA
DIODES
55
X
X
X
X
Zener Diode, 33V
DX0048GE
DX0247CE
Zener Diode, 5.1V
AB
20F630
CU20F630
Ref. No.
D502
D503
D504
D505
D510
D601
D602
D603
D606
D608
å D701
D703
D704
D708
D710
D750
D751
D752
D755
D756
D801
D806
D807
D808
D810
D811
D812
D813
D815
D1004
D1081
D1085
D1086
D1087
D1088
D1089
D1090
D1091
å IC702
VA701
Part No.
RH-EX0652GEZZ∗
RH-EX0612GEZZ∗
RH-EX0654CEZZ∗
RH-DX0441CEZZ∗
RH-DX0131CEZZ∗
RH-DX0048GEZZ∗
VHD1SS244//-1∗
RH-EX0662GEZZ∗
RH-DX0131CEZZ∗
RH-DX0131CEZZ∗
RH-DX0111PEZZ
RH-DX0048GEZZ∗
RH-EX0650GEZZ∗
RH-DX0048GEZZ∗
RH-DX0048GEZZ∗
RH-EX0647CEZZ∗
RH-DX0229CEZZ
RH-DX0131CEZZ∗
RH-DX0048GEZZ∗
RH-DX0441CEZZ∗
RH-EX0613GEZZ∗
RH-DX0048GEZZ∗
RH-EX0625GEZZ∗
RH-DX0048GEZZ∗
RH-EX0263TAZZ∗
RH-EX0263TAZZ∗
RH-EX0263TAZZ∗
RH-EX1393CEZZ∗
RH-EX0263TAZZ∗
RH-EX1393CEZZ∗
RH-DX0048GEZZ∗
RH-EX1393CEZZ∗
RH-EX1393CEZZ∗
RH-EX1393CEZZ∗
RH-EX1393CEZZ∗
RH-EX0613GEZZ∗
RH-EX1393CEZZ∗
RH-DX0048GEZZ∗
RH-FXA003WJZZ
RH-VXA009WJZZ
★
Description
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Zener Diode, 18V
Zener Diode, 5.1V
Zener Diode
DX0441CE
DX0131CE
DX0048GE
1SS244
Zener Diode, 24V
DX0131CE
DX0131CE
DX0111PE
DX0048GE
Zener Diode, 16V
DX0048GE
DX0048GE
Zener Diode, 150V
DX0229CE
DX0131CE
DX0048GE
DX0441CE
Zener Diode, 5.1V
DX0048GE
Zener Diode, 8V
DX0048GE
Zener Diode, 8.1V
Zener Diode, 8.1V
Zener Diode, 8.1V
Zener Diode, 5.1V
Zener Diode, 8.1V
Zener Diode, 5.1V
DX0048GE
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
DX0048GE
PC123Y82
VXA009WJ
Code
Ref. No.
AA
AB
AA
AB
AB
AB
AA
AB
AB
PACKAGED CIRCUITS
PR702 RMPTP0092CEZZ X Packaged Circuit
X801 RCRSAA009WJZZ X Crystal
AD
Part No.
★
C202
C203
C204
C205
C206
C207
C208
C209
C210
C213
C301
C304
C307
C308
C310
C311
C312
C313
C321
C322
C377
C391
C392
C393
C434
C435
C436
C452
C505
C508
C509
C511
C512
C513
C514
C515
C518
C519
C601
C602
C603
C604
C605
C606
å C607
VCEA0A0JW477M+ X
VCKYCY1HF103Z∗ X
VCEA0A0JW477M+ X
VCKYCY1HF103Z∗ X
VCEA0A1HW106M+X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1HB102K∗ X
VCEA0A1CW477M+X
VCEA0A1CW106M+X
VCEA0A1HW474M+X
VCKYCY1HF153Z∗ X
VCEA0A1HW225M+X
VCEA0A1HW474M+X
VCEA0A1HW335M+X
VCKYCY1HF153Z∗ X
VCEA0A1HW335M+X
VCEA0A1HW105M+X
VCEA0A1CW107M+X
VCKYPA1HB102K+ X
VCQYTA1HM103J+ X
VCEA0A1EW108M+X
VCEA0A1CW106M+X
VCE9GA1CW106M+X
VCKYCY1HF103Z∗ X
VCEA9M1CW106M+ X
VCEA0A1HW107M+X
VCFYAA2AA224J+ X
VCKYD41CY103N∗ X
VCEA0A1VW477M+X
VCKYPA2HB102K+ X
VCEA0A1VW108M+X
VCFYSA1JB273J+ X
VCEACA1HC335J+ X
VCKYCY1HF103Z∗ X
VCKYCY1HB102K∗ X
VCQYTA1HM563J+ X
VCEA0A1HW475M+X
VCEA0A1HW105M+X
VCEA0A2EW336M+X
VCKYPA2HB102K+ X
VCKYPA2HB102K+ X
VCFPVC3ZA902H X
C608
C610
C611
VCKYPA2HB561K+ X
VCFYSB2EB823J X
VCFPVC2DB244J X
C641
C642
C643
C650
å C701
C702
C703
C705
C706
å C711
C713
C718
C737
C738
C743
C744
C751
C752
C753
C754
C755
C756
C758
C759
C784
C801
VCEA0A1EW108M+X
VCEA0A1EW476M+X
VCEA0A1CW477M+X
VCKYPA2HB101K+ X
RC-FZ029SCEZZ X
RC-KZ0029CEZZ+ X
RC-KZ0029CEZZ+ X
RC-EZA070WJZZ X
VCQYTA1HM103J+ X
VCFYFA1HA334J+ X
RC-KZ016SCEZZ X
VCKYPA2HB472K+ X
VCEA0A1EW226M+X
RC-KZ0040CEZZ X
VCKYPH3DB561K X
VCQYTA1HM104J+ X
RC-KZ0106GEZZ X
VCKYPH3DB561K X
RC-EZ0724CEZZ X
RC-EZ0638CEZZ X
VCQYTA1HM103J+ X
VCEA0A1EW108M+X
VCEA0A1HW225M+X
VCKYCY1HB102K∗ X
VCKYCY1HB103K∗ X
VCFYFA1HA105J+ X
FILTERS
CF201 RFiLC0447CEZZ
CF802 RFiLC0446CEZZ
SF201 RFiLC0405CEZZ
X Filter, FiLC0447CE
X Filter, FiLC0446CE
X Filter, FiLC0405CE
AD
COILS
L202
L203
L204
L602
L603
å L701
å L703
L751
L801
L802
L803
L804
L806
L807
L1861
L1862
VP-CF270K0000∗
VP-DF270K0000∗
VP-XF1R2K0000∗
RCiLP0223CEZZ
RCiLZA006WJZZ
RCiLF0078PEZZ
RCiLF0078PEZZ
RCiLP0225CEZZ
VP-DF100K0000∗
VP-DF100K0000∗
VP-DF100K0000∗
VP-XF150K0000∗
VP-DF100K0000∗
VP-XF1R2K0000∗
VP-XF8R2K0000∗
VP-XF8R2K0000∗
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Peaking, 27µH
Peaking, 27µH
Peaking, 1.2µH
Coil
Coil
Coil
Coil
Coil
Peaking, 10µH
Peaking, 10µH
Peaking, 10µH
Peaking, 15µH
Peaking, 10µH
Peaking, 1.2µH
Peaking, 8.2µH
Peaking, 8.2µH
AA
AA
AA
AA
TRANSFORMERS
å
çå
å
T601
T602
T701
RTRNZ0026PEZZ X Transformer
RTRNFA012WJZZ X H-Volt Transformer
RTRNWA036WJZZ X Transformer
C201
VCEA0A1CW476M+X 47
CAPACITORS
16V
Electrolytic
AA
56
Description
470
6.3V Electrolytic
0.01 50V Ceramic
470
6.3V Electrolytic
0.01 50V Ceramic
10
50V Electrolytic
0.01 50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
1000p 50V Ceramic
470
16V Electrolytic
10
16V Electrolytic
0.47 50V Electrolytic
0.015 50V Ceramic
2.2
50V Electrolytic
0.47 50V Electrolytic
3.3
50V Electrolytic
0.015 50V Ceramic
3.3
50V Electrolytic
1
50V Electrolytic
100
16V Electrolytic
1000p 50V Ceramic
0.01 50V Mylar
1000 25V Electrolytic
10
16V Electrolytic
10
16V Electrolytic
0.01 50V Ceramic
10
16V Electrolytic
100
50V Electrolytic
0.22 100V Mylar
0.01 16V Ceramic
470
35V Electrolytic
1000p 500V Ceramic
1000 35V Electrolytic
0.027 63V Mylar
3.3
50V Electrolytic
0.01 50V Ceramic
1000p 50V Ceramic
0.056 50V Mylar
4.7
50V Electrolytic
1
50V Electrolytic
33
250V Electrolytic
1000p 500V Ceramic
1000p 500V Ceramic
9000p 1800V
MetalIzed Polypro Film
560p 500V Ceramic
0.082 250V Mylar
0.24 200V
MetalIzed Polypro Film
1000 25V Electrolytic
47
25V Electrolytic
470
16V Electrolytic
100p 500V Ceramic
0.22 AC125V Plastic
0.01 250V Ceramic
0.01 250V Ceramic
470
200V Electrolytic
0.01 50V Mylar
0.33 50V Mylar
470p 250V Ceramic
4700p 500V Ceramic
22
25V Electrolytic
820p 2kV Ceramic
560p 2000V Ceramic
0.1
50V Mylar
3300p AC250V Ceramic
560p 2000V Ceramic
100
160V Electrolytic
33
160V Electrolytic
0.01 50V Mylar
1000 25V Electrolytic
2.2
50V Electrolytic
1000p 50V Ceramic
0.01 50V Ceramic
1
50V Mylar
Code
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AB
AB
AB
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AA
AB
AB
AB
AA
AB
AB
AB
AC
AA
AB
AA
AA
AA
20F630
CU20F630
Ref. No.
C802
C803
C804
C805
C806
C807
C808
C809
C810
C811
C812
C813
C814
C815
C816
C817
C818
C819
C820
C821
C822
C823
C824
C825
C826
C827
C828
C829
C831
C833
C834
C835
C836
C837
C839
C840
C841
C842
C843
C845
C846
C847
C848
C1001
C1003
C1004
C1006
C1007
C1008
C1009
C1011
C1012
C1013
C1014
C1015
C1081
C1849
C1855
C1856
C1861
C1862
C1863
C1864
★
Part No.
VCKYCY1HF103Z∗ X
VCEA0A1AW476M+X
VCKYCY1HF103Z∗ X
VCEA0A1HW105M+X
VCKYCY1HF103Z∗ X
VCEA0A1CW337M+X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1EF104Z∗ X
VCKYCY1EF104Z∗ X
VCKYCY1EF104Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1EF104Z∗ X
VCEA0A1AW107M+X
VCEA0A1HW475M+ X
VCCCCY1HH121J∗ X
VCEA0A1HW474M+X
VCKYCY1HF153Z∗ X
VCE9GA1HW105M+X
VCKYCY1HF103Z∗ X
VCEA0A1CW337M+X
VCE9EM1HW105M+ X
VCKYPA1HF103Z+ X
VCEA9M1CW476M+ X
VCKYPA1HB103K+ X
VCEA0A1CW476M+X
VCKYCY1EF104Z∗ X
VCKYCY1EF104Z∗ X
VCEA0A1CW107M+X
VCEA0A1CW106M+X
VCKYCY1HF103Z∗ X
VCEA0A1HW105M+X
VCCCCY1HH680J∗ X
VCKYCY1EF104Z∗ X
VCCCCY1HH101J∗ X
VCEA9M1HW474M+ X
VCEA9M1HW105M+ X
VCKYCY1CF224Z∗ X
VCKYCY1HF103Z∗ X
VCCCCY1HH220J∗ X
VCEA0A1HW105M+X
VCEA0A0JW107M+ X
VCEA0A1CW106M+X
VCKYCY1CF474Z∗ X
VCEA0A1HW225M+X
VCEA0A1CW107M+X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1HB221K∗ X
VCEA0A1HW105M+X
VCKYCY1HB102K∗ X
VCEA0A1HW475M+X
VCCCCY1HH101J∗ X
VCEA0A1HW104M+X
VCFYFA1HA223J+ X
VCKYCY1HB561K∗ X
VCKYCY1HB102K∗ X
VCCCCY1HH221J∗ X
VCKYCY1HB102K∗ X
VCCCCY1HH221J∗ X
VCKYCY1HB102K∗ X
Description
0.01
47
0.01
1
0.01
330
0.01
0.01
0.01
0.1
0.1
0.1
0.01
0.01
0.1
100
4.7
120p
0.47
0.015
1
0.01
330
1
0.01
47
0.01
47
0.1
0.1
100
10
0.01
1
68p
0.1
100p
0.47
1
0.22
0.01
22p
1
100
10
0.47
2.2
100
0.01
0.01
220p
1
1000p
4.7
100p
0.1
0.022
560p
1000p
220p
1000p
220p
1000p
50V
10V
50V
50V
50V
16V
50V
50V
50V
25V
25V
25V
50V
50V
25V
10V
50V
50V
50V
50V
50V
50V
16V
50V
50V
16V
50V
16V
25V
25V
16V
16V
50V
50V
50V
25V
50V
50V
50V
16V
50V
50V
50V
6.3V
16V
16V
50V
16V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Mylar
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Code
Ref. No.
AA
RJ19
RJ22
RJ23
RJ33
RJ35
RJ37
RJ39
RJ41
RJ42
RJ43
RJ47
RJ50
RJ51
RJ52
RJ53
RJ60
RJ62
RJ63
RJ65
RJ69
RJ70
RJ71
RJ72
RJ75
RJ76
C211
R201
R202
R205
R206
R207
R208
R209
R216
R220
R301
R302
R303
R304
R305
R307
R308
R310
R311
R314
R315
R362
R363
R364
R365
R381
R382
R383
R384
R431
R432
R433
R434
R435
R437
R461
R462
R502
R503
R504
R506
R507
R513
R514
R520
R522
R523
R524
R525
R526
R528
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RESISTORS
RJ1
RJ3
RJ7
RJ9
RJ10
RJ11
RJ13
RJ14
RJ15
RJ16
RJ17
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
X
X
X
X
X
X
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
57
Part No.
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF101J∗
VRS-CY1JF101J∗
VRS-CY1JF680J∗
VRS-CY1JF122J∗
VRS-CY1JF221J∗
VRS-CY1JF331J∗
VRS-CY1JF392J∗
VRS-VV3LB333J
VRS-CY1JF221J∗
VRS-CY1JF102J∗
VRN-VV3DB1R2J
VRS-CY1JF103J∗
VRD-RA2BE683J∗
VRS-CY1JF274J∗
VRS-CY1JF222J∗
VRS-CY1JF392J∗
VRS-CY1JF473J∗
VRD-RA2BE272J∗
VRS-CY1JF392J∗
VRS-CY1JF222J∗
VRS-CY1JF332J∗
VRS-CY1JF564J∗
VRS-CY1JF332J∗
VRS-CY1JF564J∗
VRS-CY1JF564J∗
VRS-CY1JF332J∗
VRS-CY1JF564J∗
VRS-CY1JF332J∗
VRS-CY1JF101J∗
VRS-CY1JF750J∗
VRS-CY1JF750J∗
VRS-CY1JF750J∗
VRS-CY1JF750J∗
VRS-CY1JF101J∗
VRS-CY1JF750J∗
VRS-CY1JF101J∗
VRS-RG3AB102J+
VRN-RL3DB1R2J+
VRS-CY1JF222J∗
VRS-RG3AB331J+
VRD-RM2HD1R0J∗
VRD-RM2HD333J∗
VRD-RM2HD682J∗
VRS-CY1JF123J∗
VRS-CY1JF101J∗
VRD-RA2BE101J∗
VRD-RA2BE103J∗
VRD-RA2BE122J∗
VRD-RA2BE101J∗
VRS-CY1JF683J∗
★
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Description
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
100
100
68
1.2k
220
330
3.9k
33k
220
1k
1.2
10k
68k
270k
2.2k
3.9k
47k
2.7k
3.9k
2.2k
3.3k
560k
3.3k
560k
560k
3.3k
560k
3.3k
100
75
75
75
75
100
75
100
1k
1.2
2.2k
330
1
33k
6.8k
12k
100
100
10k
1.2k
100
68k
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
3W
1/16W
1/16W
2W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1W
2W
1/16W
1W
1/2W
1/2W
1/2W
1/16W
1/16W
1/8W
1/8W
1/8W
1/8W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Metal Oxide
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
20F630
CU20F630
Ref. No.
R602
R603
R604
R605
R606
å R608
å R611
å R612
R613
R614
R615
R616
R617
R618
å R621
R622
R631
R632
å R633
R637
R638
R639
R642
R643
R661
R662
R701
R702
R705
R706
R707
R708
R710
R711
R713
R715
R716
R717
R725
R726
R742
R743
R744
R745
R746
R753
R754
R755
R756
R759
R766
R767
R768
R802
R803
R804
R805
R806
R807
R808
R810
R812
R814
R815
R816
R817
R818
R823
R824
R826
R827
R828
R829
R830
R831
R832
Part No.
VRD-RA2BE393J∗
VRD-RA2BE273J∗
VRD-RA2BE473J∗
VRD-RM2HD104J∗
VRN-RL3LBR27J+
VRD-RM2HD102J∗
VRN-RL3ABR27J+
VRD-RM2HD270J∗
VRS-CY1JF000J∗
VRD-RA2BE154J∗
VRD-RA2BE102J∗
VRD-RA2BE102J∗
VRS-CY1JF123J∗
VRS-CY1JF103J∗
VRN-RL2HC4R7J+
VRS-VV3DB682J
VRS-KT3LB391J
VRS-RG3LB122J+
VRS-KA3NG3R3K
VRD-RA2BE331J∗
VRD-RA2BE331J∗
VRD-RM2HD562J∗
VRD-RM2HD470J∗
VRS-KA3HG912J
VRS-CY1JF102J∗
VRS-CY1JF103J∗
VRW-KQ3NC1R5K
VRD-RM2HD100J∗
VRN-VV3DBR33J
VRN-VV3DBR33J
VRD-RM2HD270J∗
VRD-RA2BE102J∗
VRS-RG2HC103J+
VRD-RA2BE394J∗
VRD-RM2HD122J∗
VRD-RA2BE150J∗
VRD-RA2BE223J∗
RR-DZ0049CEZZ∗
VRD-RM2HD821J∗
VRN-RL2HCR47J+
VRD-RA2BE183J∗
VRS-CY1JF332J∗
VRS-CY1JF332J∗
VRD-RA2BE472J∗
VRD-RA2BE223J∗
VRD-RM2HD124J∗
VRN-RL3DB8R2J+
VRS-RG3DB150J+
VRS-RG3DB121J+
VRS-RG3DB101J+
VRS-CY1JF333J∗
VRD-RA2BE103J∗
VRS-CY1JF332J∗
VRS-CY1JF682J∗
VRS-CY1JF103J∗
VRS-CY1JF222J∗
VRS-CY1JF222J∗
VRS-CY1JF222J∗
VRS-CY1JF222J∗
VRD-RA2BE273J∗
VRS-CY1JF101J∗
VRS-CY1JF101J∗
VRS-CY1JF473J∗
VRS-CY1JF473J∗
VRS-CY1JF223J∗
VRS-CY1JF473J∗
VRS-RG3AB151J+
VRD-RA2BE101J∗
VRD-RA2BE101J∗
VRD-RA2BE101J∗
VRS-CY1JF102J∗
VRS-CY1JF471J∗
VRS-CY1JF472J∗
VRS-CY1JF393J∗
VRS-CY1JF271J∗
VRS-CY1JF822J∗
★
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Description
39k 1/8W
27k 1/8W
47k 1/8W
100k 1/2W
0.27 3W
1k 1/2W
0.27 1W
27 1/2W
0
1/16W
150k 1/8W
1k 1/8W
1k 1/8W
12k 1/16W
10k 1/16W
4.7 1/2W
6.8k 2W
390 3W
1.2k 3W
3.3 7W
330 1/8W
330 1/8W
5.6k 1/2W
47 1/2W
9.1k 5W
1k 1/16W
10k 1/16W
1.5 7W
10 1/2W
0.33 2W
0.33 2W
27 1/2W
1k 1/8W
10k 1/2W
390k 1/8W
1.2k 1/2W
15 1/8W
22k 1/8W
3.9M 1/2W
820 1/2W
0.47 1/2W
18k 1/8W
3.3k 1/16W
3.3k 1/16W
4.7k 1/8W
22k 1/8W
120k 1/2W
8.2 2W
15 2W
120 2W
100 2W
33k 1/16W
10k 1/8W
3.3k 1/16W
6.8k 1/16W
10k 1/16W
2.2k 1/16W
2.2k 1/16W
2.2k 1/16W
2.2k 1/16W
27k 1/8W
100 1/16W
100 1/16W
47k 1/16W
47k 1/16W
22k 1/16W
47k 1/16W
150 1W
100 1/8W
100 1/8W
100 1/8W
1k 1/16W
470 1/16W
4.7k 1/16W
39k 1/16W
270 1/16W
8.2k 1/16W
Carbon
Carbon
Carbon
Carbon
Metal Film
Carbon
Metal Film
Carbon
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Film
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Cement
Carbon
Metal Film
Metal Film
Carbon
Carbon
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Carbon
Metal Film
Carbon
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Film
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Code
Ref. No.
R833
R835
R836
R838
R839
R840
R841
R842
R843
R844
R845
R1002
R1003
R1006
R1007
R1008
R1009
R1021
R1022
R1023
R1024
R1026
R1027
R1031
R1032
R1034
R1035
R1036
R1037
R1038
R1039
R1040
R1041
R1042
R1043
R1045
R1046
R1047
R1048
R1049
R1051
R1052
R1053
R1054
R1059
R1061
R1062
R1063
R1064
R1065
R1066
R1067
R1068
R1069
R1070
R1071
R1072
R1073
R1074
R1075
R1076
R1081
R1849
R1850
R1851
R1852
R1853
R1854
R1855
R1861
R1862
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
★
Part No.
VRS-CY1JF101J∗
VRS-CY1JF332J∗
VRD-RA2BE470J∗
VRS-CY1JF105J∗
VRS-CY1JF101J∗
VRS-CY1JF124J∗
VRD-RA2BE821J∗
VRS-CY1JF471J∗
VRS-CY1JF103J∗
VRS-CY1JF185J∗
VRS-CY1JF185J∗
VRS-CY1JF183J∗
VRS-CY1JF822J∗
VRS-CY1JF822J∗
VRS-CY1JF103J∗
VRS-CY1JF183J∗
VRS-CY1JF103J∗
VRS-CY1JF101J∗
VRS-CY1JF101J∗
VRD-RA2BE271J∗
VRS-CY1JF101J∗
VRS-CY1JF000J∗
VRS-CY1JF104J∗
VRS-CY1JF101J∗
VRS-CY1JF103J∗
VRS-CY1JF103J∗
VRD-RA2BE101J∗
VRS-CY1JF103J∗
VRS-CY1JF103J∗
VRS-CY1JF562J∗
VRS-CY1JF102J∗
VRD-RA2BE273J∗
VRD-RA2BE103J∗
VRD-RA2BE101J∗
VRS-CY1JF104J∗
VRD-RA2BE101J∗
VRS-CY1JF101J∗
VRS-CY1JF183J∗
VRS-CY1JF101J∗
VRS-CY1JF183J∗
VRS-CY1JF101J∗
VRS-CY1JF104J∗
VRS-CY1JF101J∗
VRS-CY1JF101J∗
VRS-CY1JF103J∗
VRS-CY1JF102J∗
VRS-CY1JF105J∗
VRS-CY1JF103J∗
VRS-CY1JF103J∗
VRS-CY1JF103J∗
VRS-CY1JF561J∗
VRS-CY1JF152J∗
VRS-CY1JF331J∗
VRS-CY1JF152J∗
VRS-CY1JF331J∗
VRS-CY1JF152J∗
VRS-CY1JF221J∗
VRS-CY1JF101J∗
VRS-CY1JF103J∗
VRS-CY1JF331J∗
VRS-CY1JF102J∗
VRS-CY1JF103J∗
VRS-CY1JF222J∗
VRS-CY1JF472J∗
VRS-CY1JF221J∗
VRS-CY1JF221J∗
VRS-CY1JF221J∗
VRS-CY1JF103J∗
VRD-RA2BE102J∗
VRS-CY1JF121J∗
VRS-CY1JF121J∗
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Description
100 1/16W
3.3k 1/16W
47 1/8W
1M 1/16W
100 1/16W
120k 1/16W
820 1/8W
470 1/16W
10k 1/16W
1.8M 1/16W
1.8M 1/16W
18k 1/16W
8.2k 1/16W
8.2k 1/16W
10k 1/16W
18k 1/16W
10k 1/16W
100 1/16W
100 1/16W
270 1/8W
100 1/16W
0
1/16W
100k 1/16W
100 1/16W
10k 1/16W
10k 1/16W
100 1/8W
10k 1/16W
10k 1/16W
5.6k 1/16W
1k 1/16W
27k 1/8W
10k 1/8W
100 1/8W
100k 1/16W
100 1/8W
100 1/16W
18k 1/16W
100 1/16W
18k 1/16W
100 1/16W
100k 1/16W
100 1/16W
100 1/16W
10k 1/16W
1k 1/16W
1M 1/16W
10k 1/16W
10k 1/16W
10k 1/16W
560 1/16W
1.5k 1/16W
330 1/16W
1.5k 1/16W
330 1/16W
1.5k 1/16W
220 1/16W
100 1/16W
10k 1/16W
330 1/16W
1k 1/16W
10k 1/16W
2.2k 1/16W
4.7k 1/16W
220 1/16W
220 1/16W
220 1/16W
10k 1/16W
1k 1/8W
120 1/16W
120 1/16W
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Metal Oxide
Metal Oxide
SWITCHES
S1001 QSW-K0202PEZZ+ X Switch, CH-UP
S1002 QSW-K0202PEZZ+ X Switch, CH-DOWN
S1003 QSW-K0202PEZZ+ X Switch, VOL.-UP
AA
58
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
20F630
CU20F630
Ref. No.
★
Part No.
Description
Code
Ref. No.
S1004 QSW-K0202PEZZ+ X Switch, VOL.-DOWN
S1005 QSW-K0202PEZZ+ X Switch, MENU
S1006 QSW-K0114CEZZ X Switch, POWER
å
å
å
BALUN
FB701 RBLN-0020CEZZ+ X Balun, BLN-0020CE
AB
MISCELLANEOUS PARTS
ACC701 QACCDA015WJPZ X
F701 QFS-B4023CEZZ X
FH701 QFSHD1013CEZZ+ X
FH702 QFSHD1014CEZZ+ X
J401 QJAKGA015WJZZ X
J402 QJAKE0108CEZZ X
J403 QJAKE0183CEZZ X
J404 QJAKE0184CEZZ X
J405 QJAKG0093CEZZ X
J406 QJAKFA008WJZZ X
P310 QCNW-A482WJZZ X
P302 QPLGN0461CEZZA X
P407 QPLGN0361CEZZA X
P601 QPLGN0660CEZZ X
P602 QPLGN0461CEZZA X
P603 QPLGN0361CEZZA X
P701 QPLGN0260CEZZ X
P705 QTiPM0083CEZZ X
P1001 QPLGN0561CEZZA X
P1002 QPLGN0561CEZZA X
P1007 QPLGN0461CEZZA X
P1008 QPLGN0461CEZZA X
P1011 QPLGN0361CEZZA X
P1012 QPLGN0361CEZZA X
P1014 QCNW-A482WJZZ X
RMC1001 RRMCU0222CEZZ X
å RY701 RRLYJ0093CEZZ
X
RDA501 PRDARA010WJFW X
RDA602 PRDAR0224PEFW X
RDA701 PRDARA026WJFW X
QCNW-A529WJZZ X
QCNW-A625WJZZ X
å
å
AC Cord
Fuse, 4A/125V
Fuse Holder
Fuse Holder
Jack, 9Pin
Jack, 3Pin
Jack, 3Pin
Jack, 3Pin
Rear AV In Jack
Jack
Connecting Cord, 7Pin(DF)
Plug, 4pin(S)
Plug, 3Pin(WF)
Plug, 6Pin(K1-6)
Plug, 4Pin(H)
Plug, 3Pin(TP651-3)
Plug, 2Pin(M1-2)
Tip
Plug, 5Pin(K)
Plug, 5Pin(BC)
Plug, 4Pin(FAV)
Plug, 4Pin(RAV)
Plug, 3Pin(FAV)
Plug, 3Pin(AN)
Connecting Cord, 7Pin(DF)
Remote Receiver
Relay
Heat Sink for IC501
Heat Sink for Q602
Heat Sink for Q701
Connecting Cord
Connecting Cord
AB
AA
AA
R859
R861
R863
R864
R876
R877
R878
R880
R881
R882
R889
R891
R892
R894
R895
★
Part No.
VRS-VV3DB123J
VRS-VV3DB123J
VRS-VV3DB123J
VRD-RA2BE470J∗
VRD-RA2BE121J∗
VRD-RA2BE121J∗
VRD-RA2BE121J∗
VRD-RM2HD332J∗
VRD-RM2HD332J∗
VRD-RM2HD332J∗
VRD-RA2BE821J∗
VRD-RA2BE561J∗
VRD-RA2BE391J∗
VRD-RA2BE152J∗
VRD-RA2BE561J∗
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Description
12k
12k
12k
47
120
120
120
3.3k
3.3k
3.3k
820
560
390
1.5k
560
2W
2W
2W
1/8W
1/8W
1/8W
1/8W
1/2W
1/2W
1/2W
1/8W
1/8W
1/8W
1/8W
1/8W
Metal Oxide
Metal Oxide
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Code
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
P860 QPLGN0461CEZZ X Plug, 4Pin(H)
P880 QPLGN0561CEZZ X Plug, 5Pin(K)
SC851 QSOCV0933CEZZ X Socket, 12Pin
AB
AB
AB
AB
AB
DUNTKB271FMA3(20F630)
DUNTKB271WEA3(CU20F630)
PWB-E MTS MODULE UNIT
AB
AB
AB
AB
AB
AB
INTEGRATED CIRCUITS
IC3001 VHiCXA2074Q-1S X CXA2074Q
IC3002 VHiMM1501XN-1∗ X MM1501XNRE
TRANSISTORS
AD
Q3001
Q3002
Q3004
Q3005
Q3006
Q3007
VS2SD601AR/-1∗
VS2SD601AR/-1∗
VS2SD601AR/-1∗
VS2SD601AR/-1∗
VS2SD601AR/-1∗
VS2SD601AR/-1∗
C3001
C3002
C3003
C3004
C3005
C3006
C3007
C3008
C3009
C3010
C3011
C3012
C3013
C3014
C3015
C3016
C3017
C3018
C3019
C3020
C3021
C3022
C3023
C3024
C3025
C3026
C3030
C3031
C3034
C3037
C3038
C3039
C3042
C3043
VCE9GA1HW475M+X
VCKYCY1HB562K∗ X
VCQYTA1HM123J+ X
VCEA0A1HW105M+X
VCEA0A1HW475M+X
VCEA0A1CW106M+X
VCEA0A1HW475M+X
VCKYCY1HF103Z∗ X
VCEA0A1CW227M+X
VCE9GA1HW475M+X
VCEA0A1HW475M+X
VCE9GA1HW475M+X
VCKYCY1HB272K∗ X
VCQYTA1HM473J+ X
VCEACA1HC335K+ X
VCE9GA1HW475M+X
VCEACA1CC106K+ X
VCEA0A1HW105M+X
VCEA0A1CW106M+X
VCEA0A1CW106M+X
VCEA0A1CW106M+X
VCEA0A1CW106M+X
VCKYCY1HF103Z∗ X
VCKYCY1HF103Z∗ X
VCKYCY1HF473Z∗ X
VCKYCY1HF473Z∗ X
VCQYTA1HM682J+ X
VCKYCY1HF682Z∗ X
VCEA0A1HW224M+X
VCEA0A1HW335M+X
VCEA0A1HW335M+X
VCEA0A1HW224M+X
VCKYCY1HB681K∗ X
VCKYCY1HB681K∗ X
X
X
X
X
X
X
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
2SD601AR
AA
AA
AA
AA
AA
AA
CAPACITORS
DUNTKA599WEB4(20F630)
DUNTKA599WEB5(CU20F630)
PWB-B CRT UNIT
TRANSISTORS
Q853
Q854
Q855
Q894
VS2SC3789//2E
VS2SC3789//2E
VS2SC3789//2E
VS2SA1015Y/1E+
X
X
X
X
2SC3789
2SC3789
2SC3789
2SA1015Y
D859
D898
VHD1SS119//-1∗
VHD1SS119//-1∗
L851
VP-MK820K0000+ X Peaking, 82µH
C851
C852
C853
C880
C893
VCKYPA1HB221K+ X
VCKYPA1HB221K+ X
VCKYPA1HB221K+ X
RC-KZ0153CEZZ X
VCEA0A1CW336M+X
DIODES
X 1SS119
X 1SS119
AA
AA
COIL
CAPACITORS
220p
220p
220p
1000p
33
50V
50V
50V
3kV
16V
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
RESISTORS
R849
R850
R851
R852
R854
R855
VRD-RA2BE271J∗
VRD-RA2BE470J∗
VRD-RA2BE470J∗
VRD-RA2BE470J∗
VRD-RA2BE331J∗
VRD-RA2BE331J∗
X
X
X
X
X
X
270
47
47
47
330
330
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
AA
AA
AA
AA
AA
AA
59
4.7
5600p
0.012
1
4.7
10
4.7
0.01
220
4.7
4.7
4.7
2700p
0.047
3.3
4.7
10
1
10
10
10
10
0.01
0.01
0.047
0.047
6800p
6800p
0.22
3.3
3.3
0.22
680p
680p
50V
50V
50V
50V
50V
16V
50V
50V
16V
50V
50V
50V
50V
50V
50V
50V
16V
50V
16V
16V
16V
16V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
Electrolytic
Ceramic
Mylar
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Mylar
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Mylar
Ceramic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
AB
AA
AA
AA
AA
AA
AB
AB
AA
AB
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
20F630
CU20F630
Ref. No.
★
Part No.
C3044
C3045
C3046
C3047
C3048
C3080
C3081
C3082
C3083
VCEA0A1EW476M+X
VCEA0A1HW335M+X
VCEA0A1HW335M+X
VCEA0A1HW335M+X
VCEA0A1HW335M+X
VCEA0A1CW106M+X
VCEA0A1CW106M+X
VCKYCY1HF103Z∗ X
VCEAKA1CW106M+ X
RJ2
RJ4
R3001
R3002
R3003
R3004
R3005
R3007
R3008
R3010
R3011
R3012
R3013
R3014
R3016
R3018
R3019
R3021
R3024
R3025
R3026
R3027
R3028
R3029
R3030
R3031
R3032
R3033
R3034
R3035
R3036
R3080
R3081
R3082
R3083
R3084
R3085
VRS-CY1JF000J∗
VRS-CY1JF000J∗
VRS-CY1JF221J∗
VRS-CY1JF221J∗
VRS-CY1JF105J∗
VRS-CY1JF104J∗
VRS-CY1JF623J∗
VRS-CY1JF332J∗
VRS-CY1JF302J∗
VRS-CY1JF392J∗
VRS-CY1JF102J∗
VRS-CY1JF102J∗
VRS-CY1JF102J∗
VRS-CY1JF102J∗
VRS-CY1JF102J∗
VRS-CY1JF102J∗
VRS-CY1JF102J∗
VRS-CY1JF102J∗
VRS-CY1JF000J∗
VRS-CY1JF272J∗
VRS-CY1JF331J∗
VRS-CY1JF392J∗
VRS-CY1JF683J∗
VRS-CY1JF392J∗
VRS-CY1JF683J∗
VRS-CY1JF182J∗
VRS-CY1JF223J∗
VRS-CY1JF102J∗
VRS-CY1JF182J∗
VRS-CY1JF223J∗
VRS-CY1JF102J∗
VRS-CY1JF101J∗
VRS-CY1JF101J∗
VRS-CY1JF103J∗
VRS-CY1JF103J∗
VRS-CY1JF103J∗
VRS-CY1JF103J∗
P3001
P3002
P3003
P3004
P3008
P3009
P3012
P3013
QPLGZ0810CEZZ
QPLGN0441CEZZ
QPLGN0441CEZZ
QPLGN0361CEZZ
QPLGZ0810CEZZ
QPLGZ0610CEZZ
QPLGN0241CEZZ
QPLGN0241CEZZ
Description
47
3.3
3.3
3.3
3.3
10
10
0.01
10
25V
50V
50V
50V
50V
16V
16V
50V
16V
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Electrolytic
Ceramic
Electrolytic
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Metal Oxide
Code
Ref. No.
AA
0
0
220
220
1M
100k
62k
3.3k
3k
3.9k
1k
1k
1k
1k
1k
1k
1k
1k
0
2.7k
330
3.9k
68k
3.9k
68k
1.8k
22k
1k
1.8k
22k
1k
100
100
10k
10k
10k
10k
SP301 VSP1205PB09WA X
SP302 VSP1205PB09WA X
LHLDW1003PEZZ X
QCNW-A299WJZZ X
QCNW-A530WJN1 X
QCNW-A531WJN1 X
QCNW-A532WJN1 X
QCNW-A534WJN1 X
QCNW-A871WJZZ X
QCNW-A872WJZZ X
QCNW-A873WJZZ X
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
X
X
X
X
X
X
X
X
Plug, 8Pin
Plug, 4Pin(RAV)
Plug, 4Pin(FAV)
Plug, 3Pin(WF)
Plug, 8Pin
Plug, 6Pin
Plug, 2Pin(AV)
Plug, 2Pin(AN)
★
Description
MISCELLANEOUS PARTS
RESISTORS
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Part No.
AB
AA
AA
AB
AB
AA
AA
60
Speaker(L)
Speaker(R)
Wire Holder, x2
Connecting Cord (K)
Connecting Cord (AN)
Connecting Cord (FAV)
Connecting Cord (RAV)
Connecting Cord (MTS)
Connecting Cord
Connecting Cord
Connecting Cord
Code
20F630
CU20F630
Ref. No.
Part No.
★
Description
Code
Ref. No.
Part No.
ACCESSORIES
1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
2
AB
ACCESSORIE(NOT REPLACEMENT ITEM)
TCAUH3045GJZZ
TCAUS3001GJZZ
TCAUS3002GJZZ
- Caution Card
- Caution Card(CU20F630)
- Caution Card(CU20F630)
–
–
–
–
Packing Case
Wrapping Paper
Buffer Material
Polyethylene Bag
Code
CCABAA323WEH0 X
Not Available
–
HBDGB3155CESA X
HDECQA119WJSA X
JBTN-A070WJKA X
MSPRC0005PEFW X
GDORFA015WJKA X
MSPRPA012WJFW X
HiNDPA194WJSA X
GCABBA088WJKA X
Front Cabinet Ass’y
Front Cabinet
SHARP Badge
LED/RC Cover
Power Button
Power Button Spring
Door
Door Spring
Indication Plate
Rear Cabinet
—
AB
—
—
—
CABINET PARTS LOCATION
PACKING PARTS
NOT REPLACEMENT ITEM)
SPAKCA696WJZZ
SPAKPA055WJZZ
SPAKXA145WJZZ
SSAKA0101GJZZ
Description
CABINET PARTS
SUPPLIED ACCESSORIES
RRMCGA108WJSA X Infrated R/C Unit
TGAN-0001GJZZ X Guarantee Card
(20F630)
TiNS-A725WJZZ
X Operation Manual
(20F630)
TiNS-A747WJZZ
X Operation Manual
(CU20F630)
★
1 1-1
—
—
—
—
2
1-2
1-4 1-5 1-3
1-6 1-7 1-8
61
20F630
CU20F630
PACKING OF THE SET
62
20F630
CU20F630
20F630
CU20F630
COPYRIGHT © 2003 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
TQ1492-S
May 2003 Printed in Japan
In Japan gedruckt
Design and Production Information
Design
: JAPAN
Production : SEMEX
MY. DS
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan