Motorola MC9190-G User manual

ATEX Zone 2
UL Division 2
Mobile Computing
User Manual
Mobile Computer MC 9190ex-NI,
Type B7-A28.-..../........
Document No. B1-A280-7D0001 Issue: April 2011
User Manual
Mobile Computer MC 9190ex-NI
Type B7-A28.-…./…….
ATEX Zone 2
UL Class I, II, III Division 2
Document No. B1-A280-7D0001
Issue: Revision 2 / August 2012
Reservation: Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.
Contents
Page
English
1 - 50
Appendix
Declaration of Conformity
Certificate of Compliance
GmbH
Max-Eyth-Straße 16
97980 Bad Mergentheim
Germany
Phone: +49 7931 597-0
Fax: +49 7931 597-119
Contact:
info@bartec.de
- blank -
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
General
Notes on this manual
The user manual is a constituent part of the product and must be kept in the direct vicinity
of the device and accessible at all times to installation, operating and maintenance
personnel.
It contains important notes, safety instructions and test certificates which are necessary
for perfect functioning when the devices are being operated and handled. It is written for
technically qualified personnel.
Read carefully
before putting
the devices into
operation.
Familiarity with and the technically perfect implementation of the safety instructions and
warnings described in this manual are preconditions for safe installation and
commissioning. The safety notes and warnings given in this documentation are given in a
general way and only qualified personnel will have the necessary specialised know-how to
interpret and implement them correctly in specific cases.
Qualifications of the personnel working with the devices
The user manual is written for all people who carry out assembly, installation,
commissioning and service work on the product, whereby the directives and standards
99/92/EC, EN 60079-17, EN 60079-19 for the gas area and EN 61241-17 and
EN 61241-19 for the dust area must be observed.
Changes to the document
BARTEC reserves the right to alter the contents of this document without notice. No
guarantee is given for the correctness of the information.
In the event of a legal dispute, the “General Terms and Conditions” of the BARTEC group
shall apply in addition.
The respective up-to-date versions of data sheets, manuals, certificates, EC Declaration
of Conformity may be downloaded from the “Ex Visualisation and Communication
Systems” product page at www.bartec-group.com or ordered directly from BARTEC
GmbH.
Handling the Product
The documents are currently available in English.
The product described in this manual has been tested and left the factory in perfect
condition as regards meeting safety requirements.
To maintain this condition and ensure that this product operates perfectly and safely, it
may be used only in the manner described by the manufacturer. Appropriate
transportation, suitable storage and careful operation are also essential for the perfect and
safe operation of this product.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
General
Use for the Intended Purpose
The versions, components, screens and windows illustrated in this User Manual are
examples only and can deviate from the actual display.
The information treated in this User Manual relates to the explosion protected version of
the MC 9190ex-NI Series.
Note
This User Manual contains all important information concerning explosion protection. In
addition, the original user manuals and product information from Motorola are also
available and these contain information about handling and commissioning. In the event
of information overlap, the information in this User Manual is valid and replaces the
Motorola information.
Documentation Set
BARTEC
−
User manual for the MC 9190ex-NI mobile computer series
(part no. B1-A280-7D0001). This user manual describes the use of the explosion
protected version of the MC 9190ex-NI mobile computer series.
−
Technical data sheet for the explosion protected version of the MC 9190ex-NI mobile
computer series - This Technical Data Sheet describes the most important ex
technical and general technical data.
−
The current version of this user manual is available upon enquiry.
Motorola
The documentation set for the MC9190 provides information corresponding with the
respective user requirements and comprises:
−
MC9190-G Series Regulatory Guide
−
User manual for the MC9190-G mobile computer series - This user manual
describes the use of the MC9190-G mobile computer series.
−
User manual for integration of the MC9190-G mobile computer series
This user manual describes the setup of the MC9190-G mobile computer, including
accessories.
−
Microsoft® Applications for Windows Mobile® 6 User Guide
This user guide describes the use of Microsoft applications.
−
Device Configuration Package
(DCP for MC9190c60) and Platform SDK (PSDK9190c60) for MC9190-G with
Windows Mobile, available at:
http://www.supportcentral.motorola.com
−
Enterprise Mobility Developer Kit
This EMDK file includes API information about writing applications, available at:
http://www.supportcentral.motorola.com
−
Latest Active Sync-Software, available at:
http://www.microsoft.com
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
−
General
The current version of the Motorola documentation is available at:
http://www.motorola.com/enterprisemobility/manuals
For Software Installation and Adjustment Possibilities refer to the Symbol/Motorola
manual:
http://www.supportcentral.motorola.com
under: - Support - Get Product Manuals - Product Manuals - Mobile Computers MC 9190-G
Safety Instructions
Safety instructions and warnings are specially highlighted in this manual and marked by
symbols.
The safety instructions and warnings are assigned to the individual work steps. Careful
handling and consistent observation of the instructions will prevent accidents, personal
injuries and damage to property.
Read carefully
before putting the
devices into
operation.
The adherence to all directions and safety instructions in this manual is a precondition for
safe working and the correct handling of the device.
The graphic representations in these instructions serve to show the information being
described and are not necessarily true to scale and they may deviate slightly from the
actual construction of the device.
Marking
Particularly important points in these instructions are marked with a symbol:
Danger!
Caution!
Attention!
Note
Non-observance leads to death or serious physical injury.
The necessary safety measures must be taken.
Warning of damage to property and financial and penal disadvantages
(e.g. loss of guarantee rights, liability etc.).
Important instructions and information on preventing disadvantageous behaviour
Important instructions and information on effective, economical
and environmentally compatible handling.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
General
Configurations
This user manual refers to the following configurations:
Configuration
Wireless
Display
Memory
Data acquisition
option
OS
Keypad
1D Laser scanner
Long Range
1D /2D
Standard Range
Imager (HD, DL,
SR)
Keypads: See below
Bluetooth
1D Laser scanner
Windows Mobile 6.5 Classic
MC 9190exNI
WPAN:
256 MB RAM/1 GB Flash memory
WLAN:
802.11 a/b/g
3.7"- Colour display
Standard Range
1D /2D
Long Range
Imager
Keypad
The following keypads are available:
−
28 key
−
43 key
−
53 key
−
53 key with VT emulation print
−
53 key with 3270 emulation print
−
53 key with 5250 emulation print
You can find specific information about the keypads under Technical Data or in the
Motorola documentation.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
- blank -
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Contens
1
Product Description............................................................................................................. 1
1.1 Definition ..................................................................................................................... 1
1.2 Use ............................................................................................................................. 2
2
Technical Data...................................................................................................................... 3
2.1 Explosion Protection ATEX Zone 2/22........................................................................ 3
2.2 Explosion Protection UL Division 2 ............................................................................. 3
2.3 Characteristics ............................................................................................................ 3
2.4 Performance Features ................................................................................................ 4
2.5 User Environment ....................................................................................................... 4
2.6 Application Development ............................................................................................ 4
2.7 Voice and Data Transmission Wireless LAN .............................................................. 5
2.8 Voice and Data Transmission Wireless PAN .............................................................. 5
2.9 Options for Data Capture ............................................................................................ 5
2.9.1 SE1524-ER 1D Long Range Scan Engine ................................................... 6
2.9.2 SE4600 1D/2D Long Range Imager Engine ................................................. 6
2.9.3 SE4500-SR 1D/2D Imager Engine ............................................................... 6
2.9.4 SE4500-HD 1D/2D Imager Engine ............................................................... 6
2.9.5 Decodable Bar Code Types.......................................................................... 7
2.10 Technical Data Battery ............................................................................................... 8
2.11 Technical Data External Interface ............................................................................... 8
2.12 Product Marking.......................................................................................................... 9
3
Safety Instructions............................................................................................................. 11
3.1 Warnings about the Mobile Computers..................................................................... 11
3.2 Warnings for Battery ................................................................................................. 12
3.3 Laser Devices ........................................................................................................... 13
3.4 LED Devices ............................................................................................................. 13
3.5 Health and Safety Recommendations ...................................................................... 13
3.5.1 Ergonomic Recommendations.................................................................... 13
3.5.2 Installation in Vehicles ................................................................................ 14
3.6 RF Exposure Guidelines ........................................................................................... 15
3.6.1 International ................................................................................................ 15
3.6.2 Europe ........................................................................................................ 15
3.6.3 US and Canada .......................................................................................... 16
3.7 Warnings and Information about Wireless Devices .................................................. 16
3.8 Warnings about the Use of Wireless Devices ........................................................... 18
3.8.1 Safety in Aircraft ......................................................................................... 18
3.8.2 Safety in Hospitals ...................................................................................... 19
3.8.3 Cardiac Pacemakers .................................................................................. 19
3.8.4 Hearing Aids ............................................................................................... 19
3.8.5 Other Medical Instruments.......................................................................... 19
3.9 Bluetooth .................................................................................................................. 19
3.9.1 Products with Bluetooth® Wireless Technology ......................................... 19
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
4
Operation ............................................................................................................................ 20
4.1 Getting started .......................................................................................................... 20
4.2 Recommended position for the MC 9190ex-NI .......................................................... 20
4.3 Parts of the MC 9190ex-NI......................................................................................... 21
4.4 Battery ...................................................................................................................... 21
4.4.1 Battery information...................................................................................... 22
4.4.2 Installing the Battery ................................................................................... 22
4.4.3 Replacing a battery ..................................................................................... 23
4.4.4 Charging the battery ................................................................................... 24
4.5 Keypad ..................................................................................................................... 28
4.5.1 Replacing Keypad....................................................................................... 28
4.6 Secure Device (SD) Card ......................................................................................... 30
4.6.1 Installing a SD Card .................................................................................... 30
4.7 Screen Protector ....................................................................................................... 31
4.7.1 Installing the Screen Protector.................................................................... 31
4.7.2 Removing the Screen Protector.................................................................. 32
4.8 Connection to the PC................................................................................................ 33
4.8.1 Active Sync ................................................................................................. 33
4.8.2 DEVICE Center or mobile device center..................................................... 33
5
Commissioning .................................................................................................................. 34
5.1.1 Display ........................................................................................................ 34
6
Software Versions.............................................................................................................. 35
6.1 AKU Version ............................................................................................................. 35
6.2 OEM Version ............................................................................................................ 35
6.3 BTExplorer Version................................................................................................... 35
6.4 Fusion Version .......................................................................................................... 35
7
Trouble shooting................................................................................................................ 36
7.1 Battery Management ................................................................................................ 36
7.1.1 Changing the Power Settings ..................................................................... 36
7.1.2 Changing the Backlight Settings ................................................................. 37
7.1.3 Changing the Keypad Backlight Settings .................................................... 37
7.1.4 Changing the settings for the display backlight........................................... 37
7.1.5 Turning Off the Radios................................................................................ 38
7.1.6 On Devices with Mobile 6.5 ........................................................................ 38
7.2 Resetting the MC 9190ex-NI ...................................................................................... 39
7.2.1 On a Windows Mobile 6.5 device ............................................................... 39
7.2.2 Warm boot .................................................................................................. 39
7.2.3 Cold Boot .................................................................................................... 39
7.2.4 Clean Boot .................................................................................................. 40
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Contents
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Contens
8
Maintenance, Inspection, Repair ...................................................................................... 41
8.1 Servicing ................................................................................................................... 42
8.2 Inspection ................................................................................................................. 42
8.3 Cleaning ................................................................................................................... 42
8.3.1 Required materials...................................................................................... 43
8.3.2 Housing ...................................................................................................... 43
8.3.3 Display ........................................................................................................ 43
8.3.4 Scan window .............................................................................................. 44
8.3.5 Interface connection ................................................................................... 44
8.3.6 Cradle/Battery contacts .............................................................................. 44
8.3.7 Cleaning interval ......................................................................................... 45
8.4 Information about Repairs ........................................................................................ 46
9
Accessories ........................................................................................................................ 47
9.1 Accessories for use in hazardous area ..................................................................... 47
9.2 Accessories for use in non hazardous area .............................................................. 48
10
Order Numbers................................................................................................................... 49
10.1 MC 9190ex-NI ............................................................................................................ 49
11
Disposal .............................................................................................................................. 49
12
Dispatch and Packaging Instructions .............................................................................. 49
13
Additional Information....................................................................................................... 50
13.1 Links ......................................................................................................................... 50
Appendix –
Declaration of Conformity
Certificate of Compliance
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Product Description
1
Product Description
1.1
Definition
The MC 9190ex-NI Mobile Computer is a compact unit for high-standard barcode scanning
in hazardous (potentially explosive) areas.
−
ATEX Zone 2 and 22
or
−
Class I, II, III Division 2
This means that even in the hazardous area the user can avail of the extensive
communication options that are already standard in other areas.
Its ergonomic design and easy operation make it an ideal support for fast data availability
in enterprise processes. A keyboard is available in different versions for manual data
capture.
The integrated 1D or 1D/2D scan engine for capturing bar codes is available as another
data capture option. The ergonomically mounted scan triggers on the MC 9190ex-NI allow
data to be captured easily in one-hand operation.
Several technologies are available for data communication with other systems and
company divisions.
−
Wireless LAN (WLAN),
−
Wireless PAN (WPAN) (Bluetooth)
These modules, which are integrated in the device, allow seamless transmission of voice
and data with easy integration into the company’s network.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 1 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Product Description
Other advantages in its use are the rugged construction, easy-to-read 3.7" VGA colour
display with touch technology and high-performance lithium ion battery.
Fast process execution is ensured by the Marvell PXA320@ processor with 806 MHz,
which is integrated in the MC 9190ex-NI, and an easy development of applications is
facilitated by the Microsoft® Windows Mobile® 6.5 operating system in conjunction with
the Enterprise Mobility Developer Kits (EMDK) from Motorola.
256 MB RAM and 1 GB flash drive integrated in the device are available for storing userdefined applications and data. For larger applications and volumes of data, BARTEC
offers SD memory cards.
1.2
Use
The Mobile Computer MC 9190ex-NI is a hand-guided piece of electric equipment. It
serves the mobile capture, processing and wireless transmission of data in hazardous
areas.
It is used exclusively in combination with operating devices which satisfy the requirements
for overvoltage category I.
The MC 9190ex-NI, type B7-A282-…./…….. series has been modified for use in the
hazardous area of:
−
UL Class I Division 2 Groups A, B, C and D
−
UL Class II Division 2, Groups F and G
−
UL Class III
−
Non hazardous area
The MC 9190ex-NI, type B7-A283-…./…….. series has been modified for use in the
hazardous area of:
−
ATEX Zone 2
−
ATEX Zone 22
−
Non hazardous area
The MC 9190ex-NI may not be used in locations of:
Page 2 of 50
−
ATEX Zone 0
−
ATEX Zone 1 and Zone 21
−
UL Class I, II Division 1
−
UL Class I, II Division 1
−
UL Class II Division 2, Groups E
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
2
Technical Data
2.1
Explosion Protection ATEX Zone 2/22
Type
Technical Data
B7-A283-…./……..
Ex protection
2.2
2.3
II 3G Ex nA IIC T6
II 3D Ex tD A22 IP54 T80 °C
Ambient temperature
-20 °C ≤ Ta ≤ +50 °C
Temperature Code
T6
Certification
B1-A283-7C0001
Explosion Protection UL Division 2
Type
B7-A282-…./……..
Ex protection type
Class I Division 2 Groups A, B, C and D
Class II Division 2 Groups F and G
Class III
Ambient temperature
-20 °C ≤ Ta ≤ +50 °C
Temperature Code
T6
Certification
UL File E321557
Characteristics
Dimensions (height x width x depth)
approx. 23.1 cm x 9.1 cm x 19.3 cm
approx. 9.1 inch x 3.6 inch x 7.6 inch
Weight including battery
approx. 710 g
approx. 25 oz
depending on the version and configuration
Display
Transflective 3.7 inch colour
Windows Mobile:
VGA
Touchscreen
Glass analog resistive touchscreen
Network connections
High-speed USB client, full-speed USB host,
Ethernet (via cradle), Bluetooth
Interfaces
RS232, USB
Keyboard variants
28 key, 43 key, 53 key,
53 key with VT emulation print,
53 key with 3270 emulation print,
53 key with 5250 emulation print
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 3 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Technical Data
No emulation software is installed on the Mobile Computers with the emulation key
version. The customer must order the emulation software separately from
Symbol/Motorola and its distributors and install it himself.
Note
The devices are modified to suit the selected keypad version. The end user can replace
the keypad later himself.
When replacing the keyboard, follow the instructions in chapter 4.5 “Keypad".
2.4
Performance Features
Processor
Marvell PXA320@ processor with 806 MHz
Memory
256 MB RAM / 1GB Flash
Expansion slot
SD card slot
Optional available extension with
Micro SD card
1 GB
2 GB
4 GB
8 GB
16 GB
Order no. 17-28BE-F006/0002
Order no. 17-28BE-F006/0003
Order no. 17-28BE-F006/0004
Order no. 17-28BE-F006/0005
Order no. 17-28BE-F006/0006
Note:
The devices are modified to suit the selected
memory versions. The end user can replace
the SD card later himself, but must follow the
instructions in chapter 4.6 “Secure Device
(SD) Card".
Operating system
2.5
Windows Mobile 6.5
User Environment
Ambient temperature
-20 °C to +50 °C
-4 °F to 122 °F
0 °C to +40 °C
32 °F to 104 °F
Ambient temperature when charging
2.6
Storage temperature (without battery)
-40 °C to +70 °C
-40 °F to 158 °F
outside the hazardous area
Air humidity
5% to 95% (non-condensing)
Protection class (EN 60529)
IP 64
Application Development
PSDK (Platform Software Developer Kit) and EMDK (Enterprise Mobility Developer Kit)
available through Motorola Support Central Web site.
Available for
Page 4 of 50
−
C
−
Java
−
.Net
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
More tools are available from
Motorola for the devices
e.g.
2.7
Technical Data
−
Rem Capture for processing registry files.
−
Application Launcher for dividing
applications into categories and access
regulation to the individual applications or
operating system.
−
Data Wedge allows data reading by
applications that do not support any
scanner.
−
App Center is an end-user application
access control engine that restricts activity
to a set of authorized applications on
mobile devices.
Voice and Data Transmission Wireless LAN
WLAN (integrated radio module)
2.8
2.9
Wireless standard
Tri Mode IEEE 802.11a/b/g
Output power
100mW U.S. and International
Data rate
IEEE802.11a:
IEEE802.11b:
IEEE802.11g:
up to 54 Mbit/sec.
up to 11 Mbit/sec.
up to 54 Mbit/sec.
Frequency range
(country-dependent)
IEEE802.11a:
IEEE802.11b:
IEEE802.11g:
5 GHz
2.4 GHz
2.4 GHz
Safety
WPA2 Enterprise, 802.1x; EAP-TLS; TTLS
(CHAP, MS-CHAP, MS-CHAPv2, PAP or
MD5); PEAP (TLS, MSCHAPv2, EAP-GTC);
LEAP, EAP-FAST (TLS, MS-CHAPv2, EAPGTC), WPA2/AES, CCX v4, FIPS 140-2 and
IPv6 _
Antenna
integrated in the device
Voice and Data Transmission Wireless PAN
Bluetooth
Bluetooth Version 2.1 with EDR
Antenna
Integrated in the device
Options for Data Capture
Five different types of scan engines
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
SE1524-ER
SE4600
SE4500-SR
SE4500-HD
Page 5 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Technical Data
Note
2.9.1
For decode zone and more detailed information of the scan engine look into the
Integrator Guide of Motorola.
SE1524-ER 1D Long Range Scan Engine
Reading range
2.9.2
up to approx. 13.7 m
up to approx. 45 feet
SE4600 1D/2D Long Range Imager Engine
Extended range omni directional 1D/2D imaging engine reads 1D and 2D symbols as
close as 8 in./20.32 cm and as far as 30 ft./9.14 m
2.9.3
Reading range close
up to approx. 20.3 cm
up to approx. 8 inch
Reading range far
up to approx. 9.1 m
up to approx. 30 feet
SE4500-SR 1D/2D Imager Engine
Omni directional 1D/2D imaging engine reads 1D and 2D symbols
2.9.4
Reading range close
up to approx. 5.3 cm
up to approx. 2.1 inch
Reading range far
up to approx. 62.7 cm
up to approx. 24.7 inch
SE4500-HD 1D/2D Imager Engine
1D/2D DPM imaging engine reads a wide variety of DPM marks on metal, plastic and
glass surfaces, including: dot peening, laser etching, molding, stamping or casting.
Page 6 of 50
Reading range close
up to approx. 4.0 cm
up to approx. 1.6 inch
Reading range far
up to approx. 28.2 cm
up to approx. 11.1 inch
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
2.9.5
Technical Data
Decodable Bar Code Types
Laser Decode Capability MC 9190ex-NI with
SE1524-ER 1D Long Range Scan Engine
1D code
Code 39
Code 128
Code 93
Codabar
Code 11
Discrete 2 of 5
Interleaved 2 of 5
EAN-8
EAN-13
MSI
UPCA
UPCE
UPC/EAN supplementals
Coupon code
Trioptic 39
Web code
Chinese 2 of 5
RSS-14
RSS-Limited
RSS-Expanded
Imaging Decode Capability MC 9190ex-NI with
SE4500 1D/2D Imager Engine
SE4600 1D/2D Long Range Imager Engine
1D Codes
Code 39
Code 128
Code 93
Codabar
Code 11
Discrete 2 of 5
Interleaved 2 of 5
EAN-8
EAN-13
MSI
UPCA
UPCE
UPC/EAN supplementals
Coupon code
Trioptic 39
Web code
Chinese 2 of 5
RSS-14
RSS-Limited
RSS-Expanded
2D Codes
TLC39
Composite AB
Composite C
Micro PDF-417
Macro PDF-417
(Macro) Micro PDF-417
QR Code
Data Matrix
microQR
Maxi Code
PDF-417
Dutch Kix
US Postnet
US Planet
UK 4-state
Australian 4-state
Canadian 4-state
Japanese 4-state
USPS 4-state (US4CB)
Aztec
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 7 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Technical Data
2.10
Technical Data Battery
Caution!
The battery may only be charged and changed outside the hazardous area!
Battery type B7-A2Z0-0006
Lithium ions 7.4 V/2200 mAh
Operating temperature
−
during charging
−
during discharging
0 °C to +40 °C
-20 °C to +50 °C
32 °F to 104 °F
-4 °F to 122 °F
Storage temperatures
2.11
−
≤ 1 year
−
≤ 3 months
−
≤ 1 months
-25 °C to +20 °C
-25 °C to +45 °C
-25 °C to +60 °C
-13 °F to 68 °F
-13 °F to 113 °F
-13 °F to 140 °F
Relative air humidity
20 % - 85 % (non-condensing)
Backup battery
Ni-MH battery 3.6 V/15 mAh, rechargeable
Integrated in the device and replaceable only
in the factory.
Technical Data External Interface
Operating of the 17-pin data interface is only permissible outside the hazardous area
and only with devices specified by the manufacturer!
Caution!
Operating of the headset port is only permissible outside the hazardous area and only
with devices specified by the manufacturer!
Pin Outs Interface Connector
Page 8 of 50
PIN Signal Name
Description
PIN Signal Name
Description
1
USB_GND
USB
10
Cradle_DET
Grounded by
cradle when in
cradle
2
USB_D_Plus
USB
11
DTR
RS232C
3
TxD
RS232C
12
Not assigned
Not assigned
4
RxD
RS232C
13
Power_IN
12 V / 2.5 A max.
5
DCD
RS232C
14
CTS
RS232C
6
RTS
RS232C
15
USB_5V_DET
USB
7
DSR
RS232C
16
USB_D_Minus
USB
8
GND
earth, 2.5 A max.
17
EXT_Power_OUT
3.3 V @ 500 mA
9
RI
RS232C
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
2.12
Technical Data
Product Marking
MC 9190ex-NI
Warning Laser
CAUTION - CLASS 3R LASER LIGHT WHEN OPEN. AVOID DIRECT EYE
EXPOSURE.
ATTENTION - LUMIÈRE LASER DE CLASSE 3R, EN CAS D’OUVERTURE.
EXPOSITION DANGEREUSE AU FAISCEAU.
VORSICHT - LASERLICHT KLASSE 3R, WENN ABDECKUNG GEÖFFNET.
DIREKTE BESTRAHLUNG DER AUGEN VERMEIDEN.
Laser Mark of
Compliance
Ex Protection ATEX
Ex Protection UL
Type Label &
Warning of Laser
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 9 of 50
Technical Data
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Battery Type B7-A2Z0-0006
Type Label
Page 10 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Safety Instructions
3
Safety Instructions
3.1
Warnings about the Mobile Computers
Caution!
Note
Caution!
The device may not be opened by the user outside the hazardous area either! The user
may not make any alterations to the device. Do not exchange or replace components
and do not retrofit any components on internal plug connectors or slots.
Exception: SD card, battery and keypad, screen protector
−
If components other than those specified are used, the protection against
explosions can no longer be assured.
−
Substitution of any components may impair suitability for Class I, II, III Division 2 as
well as for ATEX Zone 2 and Zone 22.
−
To prevent ignition of flammable or combustible atmospheres disconnect power
before servicing!
−
Do not open or charge the device in the hazardous area!
−
Operating of the 17-pin data interface (see chapter 2.11 "Technical Data External
Interface") is only permissible outside the hazardous area and only with devices
specified by the manufacturer!
−
Operating of the headset port is only permissible outside the hazardous area and
only with devices specified by the manufacturer!
−
Protect the device from impact effects! Do not expose the operating equipment to
any caustic/aggressive liquids, vapours or mist! In the event of malfunctioning or
damage to the enclosure, take the equipment out of the potentially explosive
atmosphere immediately, bring it into a safe area and decommission it by removing
the battery!
−
If on account of adverse effects or conditions (e.g. penetration of water, fluids,
exposure to temperatures outside the specified range etc.) there is a danger of not
being able to operate the equipment safely, switch off the equipment instantly and
remove the battery.
−
Avoid the influence of heat that is higher or lower than the specified temperature
range (see chapter 2.5 "User Environment"). Do not place the devices anywhere
near sources of heat, such as for example heaters, air exit openings in airconditioners, or near cookers or other devices (including amplifiers) that radiate
heat.
−
Avoid the effects of moisture.
−
Do not put any objects into the device, into the enclosure or other openings in the
Mobile Computer. Openings in the device may not be blocked, obstructed or
covered.
−
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 11 of 50
Safety Instructions
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
−
Equipment that is damaged in any way or that does not function properly must
instantly be removed from the hazardous area and sent in for inspection/repair!
−
Take the device out of the hazardous areas before wiping it with a dry cloth or
cleaning it!
−
General statutory regulations or directives on safety at work; accident prevention
regulations and environmental protection legislation must be complied with, e.g.
Ordinance on industrial health and safety (BetrSichV) or the national ordinances.
−
Ensure safe handling of the equipment during operation by making sure the device
in a steady position and the user has sufficient space to move!
−
When transporting the equipment in vehicles, it must be placed in appropriate
compartments or fittings so that it cans neither fall off during the drive nor be
exposed to extreme vibrations.
−
The rules for hazardous areas (see NEC Article NFPA 70) must be observed. In
particular, appropriate clothing and footwear should be worn in view of the risk of
dangerous electrostatic charges. Do not wear rubber gloves or suchlike during
operation!
Attention!
3.2
Warnings for Battery
Caution!
Page 12 of 50
−
The battery may only be charged and changed outside the hazardous area!
−
It must be ensured that only original batteries of the following type/s are used in
safety-oriented operation. B7-A2Z0-0006 with 7.4 V/2200 mAh.
−
The use of imitation batteries or batteries from other manufacturers will render the
type of ignition protection ineffective and there will then be a risk of fire or explosion.
−
Keep away from children.
−
The battery may explode if disposed of in fire.
−
DO NOT short circuit or disassemble battery.
−
The battery may only be used for the purposes stated in the user manual and is
only suitable for use in the MC 9190ex-NI (type B7-A28.-…./……..).
−
If used incorrectly, there is a risk of burning. The battery should not be
disassembled over a temperature higher than +50 °C (122 °F). If the battery is
damaged, battery acid can escape from the cells and cause corrosion. For that
reason, extreme care must be taken in handling and disposing of a damaged or
leaking Li-ion battery.
−
Defective batteries must be disposed of immediately, whereby the battery disposal
regulations that apply to the respective region must be observed.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
3.3
Laser Devices
Class 2 laser devices operate with a visible low-voltage light emitting diode. As with any
bright source of light, for example the sun, the user should avoid looking directly into the
light beam. However, there is no evidence of risks in momentary or brief exposure to a
Class 2 laser.
Caution!
3.4
Safety Instructions
The use of control elements, adaptations or the application of procedures which do not
agree with the instructions described here can lead to a hazardous exposure to
radiation.
−
Laser-equipped devices from Symbol/Motorola conform to Directive 21CFR1040.10
and 1040.11. (with the exception of the deviations listed in Laser Notice no. 50 of 24
June 2007) as well as EN 60825-1:2007 and IEC 60825-1 (Ed. 2)
−
The classification of the laser apparatus is specified on a sign affixed to the device.
−
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose.
LED Devices
Complies with IEC/EN60825-1:2001 & IEC/EN60247:2006
3.5
Health and Safety Recommendations
Caution!
3.5.1
Use only the accessories, batteries and battery chargers approved by BARTEC. Do not
attempt to charge damp/wet MC 9190ex-NI or batteries. All components must be dry
before they are connected to an external power supply.
Ergonomic Recommendations
Caution!
The following recommendations should be observed to avoid or minimise potential
health problems at the workplace. Contact your local health and safety manager on site
to ensure that you are familiar with your company’s safety regulations, which serve to
protect employees in the workplace.
−
Avoid unilateral repetitive movements.
−
Posture should be as neutral as possible.
−
Avoid using excessive force.
−
Keep objects that are used frequently within easy functional reach.
−
Perform tasks at heights that suit the person and the type of work
−
Place the objects in positions that will eliminate vibrations
−
Avoid exerting direct pressure
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 13 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Safety Instructions
3.5.2
−
Provide adjustable tables and chairs.
−
Ensure sufficient clearance for easy movement
−
Provide a suitable working environment
−
Optimise work procedures
−
Alternate hands as often as possible when doing repetitive tasks.
Installation in Vehicles
RF signals can have a negative impact on electronic systems in vehicles (including safety
systems) if they have not been installed correctly or shielded adequately. If you have any
questions about your vehicle, please get in touch with the manufacturer or with a sales
representative. You can find out from the manufacturer if any additional equipment has
been installed in the vehicle. An airbag inflates with great force. DO NOT PLACE ANY
objects, such as mounted or mobile wireless equipment in the area above the airbag or in
the airbag deployment area. If the wireless equipment in the vehicle was not installed
properly, serious injuries can occur when the airbag is deployed. Position the device
within reach. Make sure you have access to the device without having to take your eyes
off the road.
Note
Connection to an alert device that will cause a horn to sound or a light to flash on
receipt of an incoming call on public roads is not permissible.
Safety in traffic
Do not make any notes or use the device while driving. Creating a “to do” list or flipping
through the address book while driving interferes with safe driving.
In road traffic you must first and foremost concentrate on your own safety and that of the
other road users. Give your full attention to the road. Check the legal regulations on the
use of wireless devices in road traffic in the respective region. Always observe them. If
you use a wireless device while driving, rely on your common sense and adhere to the
following:
1. Familiarise yourself with the wireless device and its functions, such as speed dial and
redial. These functions may prove to be useful if you wish to make a call without
taking your eyes off the road.
2. When available, use a hands-free telephone, if possible.
3. Inform the person you are speaking with that you are driving. If necessary, end the
call if there is heavy traffic or bad weather. Rain, sleet, snow, ice and even heavy
traffic can be dangerous.
4. Dial numbers carefully and keep an eye on the traffic. Make your calls when you have
stopped the car or before you set off. Plan your calls so that you can make them
when parked. If it is essential to make a call when driving, dial only part of the
number, check the road again and look in the rear mirror and then dial the rest of the
number.
Page 14 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Safety Instructions
5. Do not engage in stressful and emotional telephone calls which might take your
attention away from the road. Let the other person know that you are driving a car
and do not get involved in any discussions that might divert your attention from the
road.
6. Use your mobile device to call for help if necessary. Dial emergency services (9-1-1
in the USA and 1-1-2 in Europe) or other local emergency service numbers if there is
a fire, an accident or a medical emergency. These calls are free of charge on the
wireless device! The call can be made independently of security codes or networks
and with or without a SIM card.
7. Use your mobile device to call for help for other people in emergency situations. If
you witness a serious accident, crime or other emergency, call the emergency
service (9-1-1 in the USA and 1-1-2 in Europe) or another local emergency service
number. Remember you yourself might need help the next time.
8. Call the breakdown service or a special mobile radio number for support when
problems occur on the road. If you drive past a car with a breakdown which does not
present any serious risk to traffic, a traffic light that is not functioning, a traffic
accident with minor damage and without injured people, or a possibly stolen car,
report it to the road patrol or another special mobile radio number for assistance.
“The wireless industry reminds you to use your device/phone safely when driving.”
3.6
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Caution!
3.6.1
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognised standards relating to human exposure
to electromagnetic fields from radio devices.
3.6.2
Europe
Handheld Devices
This device was tested for typical body-worn operation. Use only BARTEC tested and
approved belt-clips, holsters, and similar accessories to ensure EU Compliance.
Note
The MC 9190ex-NI must be switched off before it may be carried on the body.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 15 of 50
Safety Instructions
3.6.3
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
US and Canada
Co-located statement
To comply with FCC RF exposure compliance requirement, the antenna used for this
transmitter must not be co-located or operating in conjunction with any other
transmitter/antenna except those already approved in this filling.
Handheld Devices
This device was tested for typical body-worn operation. Use only BARTEC tested and
approved belt-clips, holsters, and similar accessories to ensure FCC Compliance. The
use of third-party belt-clips, holsters, and similar accessories may not comply with FCC
RF exposure compliance requirements, and should be avoided.
Note
3.7
The MC 9190ex-NI must be switched off before it may be carried on the body.
Warnings and Information about Wireless Devices
Caution!
Note
Operation of the device without regulatory approval is illegal.
The use of wireless devices might be forbidden or restricted. This applies above all
when you are aboard aeroplanes, in hospitals, near explosives or in other dangerous
conditions. If you are not sure which regulations apply to the use of the device, ask for
permission before switching it on.
Radio Modules
The device contain approved radio module(s). These module(s) are identified below.
Motorola/Symbol Technologies WLAN radio 802.11 a/b/g Type(s): 21-92955
Country-Specific Roaming
This device incorporates the International Roaming feature (IEEE802.11d) which will
ensure the product operates on the correct channels for the particular country of use.
Ad-hoc Operation (5 GHz Band)
Ad-Hoc operation is limited to Channels 36-48 (5150 - 5250 MHz). Use of this band is
restricted to Indoor Use Only, any other use will make the operation of this device illegal.
Page 16 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Safety Instructions
Frequency of Operation – FCC and IC
5 GHz Only
The use in the UNII (Unlicensed National Information Infrastructure)
band 1 5150 - 5250 MHz band is restricted to Indoor Use Only; any
other use will make the operation of this device illegal.
2.4 GHz Only
The available channels for 802.11 b/g operation in the US are
Channels 1 to 11. The range of channels is limited by firmware.
European Economic Area (EEA)
The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions:
−
Maximum radiated transmit power of 100 mW EIRP in the frequency range
2.400 – 2.4835 GHz.
−
France, outside usage is restricted to 2.4 – 2.454 GHz.
−
Italy requires a user license for outside usage.
FCC requirements to protect against radio-frequency interference
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
−
Reorient or relocate the receiving antenna
−
Increase the separation between the equipment and receiver
−
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
−
Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device satisfies the requirements of part 15 of the FCC rules. The operation of the
device is subject to the following two conditions:
−
the device must not cause harmful interference
−
the device must accept all interference it receives, including interference which may
cause undesired operation.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 17 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Safety Instructions
Requirements for protection from radio-frequency interference – Canada
This class B digital device complies with the guidelines in the Canadian standard
ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters for RLAN Devices
The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:
−
Restricted Band 5.60 – 5.65 GHz
−
This device complies with RSS 210 of Industry & Science Canada. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Label Marking: The Term “IC:” before the radio certification only signifies that industry
Canada technical specifications were met.
Country-specific approvals
Regulatory markings, subject to certification, are applied to the device signifying the
radio(s) is/are approved for use in the following countries: United States, Canada, Japan,
China, S. Korea, Australia, and Europe 1, 2.
You will find detailed information on the test marks for other countries in the EC
Declaration of Conformity.
3.8
−
Note 1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria,
Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
−
Note 2: The use of RFID Devices have varying restrictions of use; please refer to
the EC Declaration of Conformity for details.
Warnings about the Use of Wireless Devices
Observe all warnings which refer to the use of wireless devices.
3.8.1
Safety in Aircraft
Switch off your wireless device whenever you are asked to do so by airport or airline staff.
If your device offers a flight mode or similar function, ask the flight crew about its proper
use.
Page 18 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
3.8.2
Safety Instructions
Safety in Hospitals
Wireless devices radiate radio frequencies and can cause interference in electrical
medical devices. If you are in a hospital, clinic or public health service, please turn off
wireless devices if asked to do so. This is to prevent any interference with sensitive
medical equipment.
3.8.3
Cardiac Pacemakers
The manufacturer recommends a minimum distance of 15 cm between a portable
handheld wireless device and a Cardiac Pacemaker to avoid potential interference. This
guideline is in accordance with independent research results and recommendations from
Wireless Technology Research.
3.8.4
−
People with implanted pacemakers:
−
Should ALWAYS keep the switched-on device at a distance of at least 15 cm away
from themselves.
−
Should not put the device into your breast pocket.
−
The device should be held at the ear furthest away from the cardiac pacemaker.
−
If you have reason to suspect interference, SWITCH OFF your device immediately.
Hearing Aids
The wireless device can cause interference with hearing aids. If there is any interference,
contact the hearing aid manufacturer to ask about solutions.
3.8.5
−
If you wear a hearing aid, do not put this device into your breast pocket.
−
The device should be held at the ear furthest away from the cardiac pacemaker.
−
If you have reason to suspect interference, SWITCH OFF your device immediately.
Other Medical Instruments
Consult your doctor or the manufacturer of the medical instrument to determine if the
operation of your wireless product my interfere with the medical instrument.
3.9
Bluetooth
3.9.1
Products with Bluetooth® Wireless Technology
This device is a Bluetooth®-approved product
More information can be found at http://www.bluetooth.org/tpg/listings.cfm
Manufacturer: Motorola --- Product: MC9190
Bluetooth® Wireless Technology for use through the EEA in the frequency range
2.400 – 2.4835 GHz
−
Maximum radiated transmit power of 100 mW EIRP in the frequency range
2.400 – 2.4835 GHz.
−
France, outside usage is restricted to 10 mW EIRP.
−
Italy requires a user license for outside usage.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 19 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
4
Operation
Before assembling the device, make sure you have all the components and documents.
Scope:
1 x MC 9190ex-NI
1 x Lithium-ion battery
1 x Strap assembly
1 x Protective overlay on the display window
1 x Stylus
1 x User manual
Caution!
4.1
The safety and accident prevention regulations relevant to the respective application
must be adhered to. The units must be completely assembled before they may be
operated.
Getting started
Carry out the following steps before first use of the MC 9190ex-NI:
1. Install a micro SD card (optional).
2. Insert the battery.
3. Charge the MC 9190ex-NI.
4.2
Page 20 of 50
Recommended position for the MC 9190ex-NI

The recommended position for the mobile computer when not in use.

In this position the device cannot be protected against damage.

The display can be damaged by objects lying on the supporting surface.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
4.3
Parts of the MC 9190ex-NI
4.4
Battery
Operation
This chapter provides information on battery functionality, battery status indications,
charging the MC 9190ex-NI charging spare batteries and power saving techniques.
The battery may only be charged and changed outside the hazardous area!
Caution!
It must be ensured that only original batteries of the following type/s are used in safetyoriented operation. B7-A2Z0-0006 with 7.4 V/2200 mAh.
The use of imitation batteries or batteries from other manufacturers will render the type
of ignition protection ineffective and there will then be a risk of fire or explosion.
The temperature range for charging the battery is 0 °C to +40 °C.
Note
Use only accessories approved by BARTEC and Motorola to charge the batteries.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 21 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
4.4.1
Battery information
BARTEC rechargeable battery packs (type B7-A2Z0-0006) are designed and constructed
to the highest standards within the industry. However, there are limitations to how long a
battery can operate or be stored before needing replacement. Many factors affect the
actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and
falls from heights. When batteries are stored over 6 months, some irreversible
deterioration in overall battery quality may occur.
Store batteries discharged in a dry, cool place, removed from the equipment to prevent
loss of capacity, rusting of metallic parts and electrolyte leakage. When storing batteries
for ½ year or longer, they should be charged and discharged at least once a year. If an
electrolyte leakage is observed, avoid any contact with affected area and properly dispose
of the battery. Replace the battery when a significant loss of run time is detected.
Batteries must be charged within the 0° to +40 °C (32° to 104° F) temperature range.
Standard warranty period for all BARTEC batteries is 1 year, regardless of whether the
battery was purchased separately or included as part of the Mobile Computer.
4.4.2
Installing the Battery
The battery may only be charged and changed outside the hazardous area!
Caution!
It must be ensured that only original batteries of the following type/s are used in safetyoriented operation. B7-A2Z0-0006 with 7.4 V/2200 mAh
The use of imitation batteries or batteries from other manufacturers will render the type
of ignition protection ineffective and there will then be a risk of fire or explosion.
Before using the MC 9190ex-NI, install a lithium-ion battery by sliding the battery into the
MC 9190ex-NI as shown in Figure 4-1: Inserting the battery
Note
Ensure the battery is fully inserted. Two audible clicks can be heard as the battery is
fully inserted. A partially inserted battery may result in unintentional data loss.
When a battery is fully inserted in a MC 9190ex-NI for the first time, upon first power up,
the device boots and powers on automatically.
Figure 4-1: Inserting the battery
Page 22 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
4.4.3
Operation
Replacing a battery
The battery may only be charged and changed outside the hazardous area!
Caution!
Attention!
It must be ensured that only original batteries of the following type/s are used in safetyoriented operation. B7-A2Z0-0006 with 7.4 V/2200 mAh
The use of imitation batteries or batteries from other manufacturers will render the type
of ignition protection ineffective and there will then be a risk of fire or explosion.
Suspend the MC 9190ex-NI prior to removing the battery. Failure to properly remove the
battery may cause the MC 9190ex-NI to cold boot and potential loss of data.
To replace the battery:
(1)
Prior to removing the battery, press the red Power button. On Windows Mobile 6.5
devices, the PowerKey Action window appears. Tap Safe Battery Swap.
(2)
The Indicator LED Bar lights red.
(3)
When the Indicator LED turns off, press the primary battery releases. The battery
partially ejects from the MC 9190ex-NI as shown in Figure 4-2: Removing the
battery.
(4)
Pause three to four seconds while the MC 9190ex-NI performs battery removal
shutdown.
(5)
Press the secondary battery release, on top of the battery, and slide the battery out
of the MC 9190ex-NI as shown in Figure 4-2: Removing the battery.
Figure 4-2: Removing the battery
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 23 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
4.4.4
Charging the battery
Before using the MC 9190ex-NI for the first time, charge the main battery until the amber
charge indicator light remains lit (see Table 4-1: Charging indications). The main battery
fully charges in less than four hours. The MC 9190ex-NI can be charged using a cradle,
the CAM, or the MSR with the appropriate power supply.
The MC 9190ex-NI is also equipped with a memory backup battery which automatically
charges from the main battery whether or not the MC 9190ex-NI is operating or is in
suspend mode. The memory backup battery retains data in memory for at least 30
minutes when the MC 9190ex-NI's main battery is removed or fully discharged. When the
MC 9190ex-NI is used for the first time or after the memory backup battery has fully
discharged, the memory backup battery requires approximately 15 hours to fully charge.
Do not remove the main battery from the MC 9190ex-NI for 15 hours to ensure that the
memory backup battery fully charges. If the main battery is removed from the
MC 9190ex-NI or the main battery is fully discharged, the memory backup battery
completely discharges in several hours.
When the main battery reaches a very low battery state, the combination of main battery
and backup battery retains data in memory for at least 72 hours.
Note
Do not remove the main battery within the first 15 hours of use. If the main battery is
removed before the backup battery is fully charged, data may be lost.
Use following to charge batteries
Cradles: The MC 9190ex-NI slips into the cradles for charging the battery in the
MC9190ex-NI (and spare batteries, where applicable). For detailed cradle setup and
charging procedures refer to the Motorola MC9190 Integrator Guide.
Note
−
Single Slot Serial/USB Cradle
−
Four Slot Ethernet Cradle
−
Four Slot Charge Only Cradle
The cradle may be used for charging and for data communication only outside the
hazardous area.
Accessories: The MC 9190ex-NI snap-on accessories provide charging capability, when
used with one of the accessory charging cables. For detailed snap-on setup and charging
procedures refer to the Motorola MC9190 Integrator Guide.
Note
Page 24 of 50
−
CAM
−
MSR
The accessories may only be used outside the hazardous areas.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
Chargers: The MC 9190ex-NI spare battery charging accessories are used to charge
batteries that are removed from the MC 9190ex-NI. For detailed spare battery charging
accessories setup and charging procedures refer to the Motorola MC9190 Integrator
Guide
Note
−
Single Slot Serial/USB Cradle
−
Four Slot Spare Battery Charger
−
Universal Battery Charger (UBC) Adapter
The chargers may only be used outside the hazardous areas.
Charge the main battery
Note
Note that battery type B7-A2Z0-0006 with 7.4 V/2200 mAh may only be charged outside
the hazardous area. Use only accessories approved by BARTEC. Do not attempt to
charge damp/wet Mobile Computers or batteries. All components must be dry before
they are connected to an external power supply.
1. Ensure the accessory used to charge the main battery is connected to the
appropriate power source.
2. Insert the MC 9190ex-NI into a cradle or attach the appropriate snap-on module.
3. The MC 9190ex-NI starts to charge automatically. The amber charge LED, in the
Indicator LED Bar, lights to indicate the charge status. See Table 4-1: Charging
indications.
Note
The main battery usually fully charges in less than four hours.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 25 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
LED
Off
Fast Blinking Amber
Slow Blinking Amber
Solid Amber
Indication
MC 9190ex-NI not in cradle or connected to a CAM or MSR.
MC 9190ex-NI not placed correctly. Charger is not powered.
Error in charging; check placement of the MC 9190ex-NI.
MC 9190ex-NI is charging.
Charging complete.
Table 4-1: Charging indications
Note
When the battery is initially inserted in the MC 9190ex-NI, the amber LED flashes once if
the battery power is low or the battery is not fully inserted.
Charge battery separately or a spare batteries
Note
Note that battery type B7-A2Z0-0006 with 7.4 V/2200 mAh may only be charged outside
the hazardous area. Use only accessories approved by BARTEC. Do not attempt to
charge damp/wet Mobile Computers or batteries. All components must be dry before
they are connected to an external power supply.
1. Remove the battery, type B7-A2Z0-0006
2. Prior to removing the battery, press the red Power button. This sets the Mobile
Computer to suspend mode.
3. Press the primary battery release(s). The battery partially ejects from the Mobile
Computer.
4. Pause 3 to 4 seconds while the Mobile Computer performs battery removal
shutdown.
5. Press the secondary battery release ( 2 in figure ), on top of the battery, and slide the
battery out of the Mobile Computer. ( 3 in figure )
6. Ensure the accessory used to charge the main battery is connected to the
appropriate power source.
Page 26 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
7. Insert the MC 9190ex-NI into a cradle or attach the appropriate snap-on module.
8. The MC 9190ex-NI starts to charge automatically. The amber charge LED, in the
Indicator LED Bar, lights to indicate the charge status. See Table 4-1: Charging
indications.
Note
The main battery usually fully charges in less than four hours.
Charge the backup battery
Note
The backup battery is installed inside of the MC 9190ex-NI, the device may not be
opened by the user outside the hazardous area either! The user may not make any
alterations to the device.
The MC 9190ex-NI is equipped with a battery backup module, which is charged
automatically when the main battery is fully charged. When the MC 9190ex-NI is taken into
operation for the first time, the battery backup module needs about 36 hours to be fully
charged. This is also the case when the main battery was removed for several hours,
which discharges the backup module. The battery backup module ensures that the data in
the working memory are retained for at least 15 minutes after the main battery of the
MC 9190ex-NI was removed. When the MC 9190ex-NI reaches a low charging state, the
data in the working memory are retained for at least 36 hours due to the combination of
main battery and battery backup module. Use a charging station or charging cable to
charge the battery. You can find information on how to set up cables and charging
stations, as well as about the charging procedure in the Motorola documentation MC9190
User manual for integration of mobile computers.
Battery status
To check the charge level of the main battery or backup battery:
−
On Windows Mobile 6.5 devices:
tap Start > Settings > System > Power to display the Power window.
To save battery power, set the MC 9190-G to turn off after a specified number of minutes.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 27 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
4.5
Keypad
4.5.1
Replacing Keypad
The MC 9190ex-NI has interchangeable modular keypads.
Caution!
−
The keypad may only be changed outside the hazardous area!
−
It must be ensured that only original keypads are used in safety-oriented operation.
−
The use of imitation keypads from other manufacturers will render the type of
ignition protection ineffective and there will then be a risk of fire or explosion.
−
Follow proper ESD precautions to avoid damaging the SD card. Proper ESD
precautions include, but are not limited to, working on an ESD mat and ensuring
that the operator is property grounded.
−
Power off the MC 9190ex-NI before start of change parts.
−
Put the MC 9190ex-NI into suspend mode before you remove the battery. Failure to
properly remove the battery may cause the MC 9190ex-NI to cold boot and
potential loss of data.
Caution!
Attention!
If the MC 9190ex-NI is in suspend mode, press the Power button to wake the device. Wait
for the MC 9190ex-NI to fully awake from suspend mode.
(1)
Turn off the MC 9190ex-NI
(2)
Remove the battery. (see figure 4.4.3 Replacing a battery)
(3)
Take out the screws at the top edge of the keypad.
Figure 4-3: Removing the keypad
(4)
Page 28 of 50
Pull the keypad downwards in the direction of the arrow and then forwards to take
it out of the MC 9190ex-NI.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
(5)
Check that the contacts and seals are clean and in good condition.
(6)
Snap on the keypad in the direction of the arrow (see Figure 4-4: Installing the
keypad) and push it upwards until the boreholes for the screws are over the
threaded sleeves.
Figure 4-4: Installing the keypad
(7)
Check that the keypad is mounted correctly.
Figure 4-5: Keypad mounted correctly
(8)
Caution!
Note
Figure 4-6: Keypad mounted incorrectly
Puss the keypad in the direction of the arrow (see Figure 4-4: Installing the
keypad) until the boreholes on the keypad are positioned over the threaded holes
on the enclosure.
Do not apply more than 0.452 NM or 4 in-lbs of torque when tightening the keypad
screws.
After the exchange of the keyboard a cold boot
(see chapter 7.2 “Resetting the MC 9190ex-NI”) must be performed.
(9)
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
The current drivers are installed on the unit and initialized automatically by the cold
boot.
Page 29 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
4.6
Secure Device (SD) Card
Caution!
The SD card may only installed and replaced outside of the hazardous area!
Only SD cards tested by BARTEC for that purpose may be used in the slot.
The SD card slot provides secondary non-volatile storage. The slot is located under the
keypad. Refer to the documentation provided with the card for more information, and
follow the manufacturer’s recommendations for use.
Caution!
Follow proper ESD precautions to avoid damaging the SD card. Proper precautions
include, but are not limited to, working on an ESD mat and ensuring that the operator is
property grounded.
BARTEC recommend to use following tested SD cards:
−
1 GB Order no. 17-F006-0002 or
−
2 GB Order no. 17-F006-0003 or
−
4 GB Order no. 17-F006-0004 or
−
8 GB Order no. 17-F006-0005 or
−
4.6.1
16 GB Order no. 17-F006-0006
Installing a SD Card
To install the micro SD card:
(1) If the MC 9190ex-NI is in standby mode, press the red Power button to activate the
device.
(2) Press the red Power button to suspend the MC 9190ex-NI.
(3) Remove the battery
(4) Remove the two keypad screws and slide the keypad down and lift off (see
chapter 4.5 “Keypad“).
(5) Lift the SD card retaining door.
(6) Position the SD card, with the contacts down, into the SD card holder (shown in
Figure 4-7: Inserting the SD card). The SD card corner notch fits into the holder only
one way.
(7) Snap the retaining door closed.
Figure 4-7: Inserting the SD card
Page 30 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Caution!
4.7
(8)
Replace the keypad and re-attach using the two screws (see chapter 4.5 “Keypad“).
(9)
Perform a warm boot.
Do not apply more than 0.452 NM or 4 in-lbs of torque when tightening the keypad
screws.
Screen Protector
Caution!
4.7.1
Operation
−
The screen protector may only be installed or removed outside the hazardous
area!
−
It must be ensured that only original screen protector used in safety-oriented
operation.
−
Use only BARTEC type 17-A1Z0-0003
−
The use of imitation screen protectors from other manufacturers will render the
type of ignition protection ineffective and there will then be a risk of fire or
explosion.
Installing the Screen Protector
A screen protector is available for the MC 9190ex-NI. BARTEC recommends using this to
minimize wear and tear. Screen protectors enhance the usability and durability of touch
screen displays.
1. Clean the display carefully from any dust or dirt.
2. Remove half of the thin cover film of the display protector and position the display
protector and position the display protector on your display. Be aware that the display
protector should be placed in the middle of your display.
3. Squeeze down the display protector lightly with a credit card from one side to the
other on your display. At the same time remove the rest of the thin cover film. Smooth
out existing bubbles with your credit card.
Attention!
Do not use any sharp object to remove the screen protector. This could damage the
display.
Note
You can order screen protector from your customer consultant or from BARTEC.
Installation instructions for the screen protector are part of the delivery scope. Part
number: 17-A1Z0-0003 screen protector, pack of 5.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 31 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Operation
4.7.2
Removing the Screen Protector
A screen protector is available for the MC 9190ex-NI. BARTEC recommends using this to
minimize wear and tear. Screen protectors enhance the usability and durability of touch
screen displays.
To remove the screen protector, lift the corner using a thin plastic card, such as a credit
card, then carefully lift it off the display.
Sample picture
Page 32 of 50
Attention!
Do not use any sharp object to remove the screen protector. This could damage the
display.
Note
You can order screen protector from your customer consultant or from BARTEC.
Installation instructions for the screen protector are part of the delivery scope. Part
number: 17-A1Z0-0003 screen protector, pack of 5.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
4.8
Operation
Connection to the PC
The MC 9190ex-NI series is delivered with a Microsoft WM 6.5 operating system or followup version. Microsoft supplies software free of charge to establish a connection to a PC
for synchronisation, installation and data exchange.
4.8.1
Active Sync
Note
To be able to communicate with various host partners, it is recommendable to install
Microsoft ActiveSync (version 4.5 or higher) on the host computer. ActiveSync
synchronises the information on the mobile computer with information on the host
computer. Changes made on the mobile computer or host computer remain in both
partners after synchronisation.
The ActiveSync Microsoft program is used for synchronising or installing software/data.
ActiveSync is available for downloading as freeware at www.microsoft.com
Supported Operating Systems:
−
Windows XP
For system requirements see the Microsoft homepage under Active Sync version 4.5 or
higher.
Further information on ActiveSync can be found in the Motorola integrator Guide or on the
Microsoft homepage.
4.8.2
DEVICE Center or mobile device center
Note
To be able to communicate with various host partners installed on Windows Vista or
Windows 7, it is recommendable to install the Microsoft Device Center on the host
computer. Device Center synchronises the information on the mobile computer with
information on the host computer. Changes made on the mobile computer or host
computer remain on both partners after synchronisation.
The Microsoft Mobile Device Center program is used for synchronising or installing
software/data. Mobile Device Center is available for downloading as freeware at
www.microsoft.com
Supported Operating Systems:
−
Windows Vista or Windows 7
For system requirements see Device Center on the Microsoft homepage
Further information on Device Center can be found in the Motorola integrator Guide or on
the Microsoft homepage.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 33 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Trouble Shooting
5
Commissioning
The operator of an electrical system in a hazardous environment must keep the operating
equipment in an orderly condition, operate it correctly, monitor it and do the required
maintenance and repairs.
Before commissioning the MC 9190ex-NI, check that all components and documents are
there.
The following conditions must be met before the device may be commissioned:
5.1.1
−
Check the MC 9190ex-NI for damage to display, scanner window and the enclosure.
−
Check that the used battery is a certified one.
−
Make sure that the battery is changed before insert in the MC 9190ex-NI.
−
Check when use a screen protector that it is a certificated one.
−
Strap, attached to the MC 9190ex-NI
−
Stylus, in the stylus silo
−
Manual inside of the box
Display
Use only the stylus included with the device to operate the touch screen. A biro, for
example, could scratch or even destroy the touch screen.
Note
The Mobile Computer must be treated carefully as the sensitive touch screen has a
glass pane which can break if subjected to a lot of strain or let fall. The guarantee will
be void if it is apparent that the damage to the touch screen is due to inappropriate use.
MC 9190ex-NI with protective film
Take off the protective film
The display as supplied from the factory is covered with a protective film. Remove the
protective film before using the device.
Page 34 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
6
Software Versions
Software Versions
This user manual various software configurations and references are made to operating
system or software versions for:
−
Adaptation Kit Update (AKU) version
−
OEM version
−
BTExplorer version
−
Fusion version
Note
6.1
The software is not relevant for the equipment explosion protection. You can find
information about this in the Motorola documentation. Motorola Homepage:
http://www.motorola.com/web/Business/CT/Enterprise+Mobility.html
Support - Product Manuals - Mobile Computers – MC9190
AKU Version
To determine the Adaptation Kit Update (AKU) version:
Tap Start > Settings > System tab > About icon > Version tab.
The second line lists the operating system version and the build number. The last part
of the build number represents the AKU number. For example, Build 23103.5.3.3
indicates that the device is running AKU version 5.3.3
6.2
OEM Version
To determine the OEM software version:
On Mobile 6.5, tab Start > Settings > System > System Information > System.
6.3
BTExplorer Version
Note
By default, the Microsoft Bluetooth stack is enabled. BTExplorer application is only
available when the StoneStreet One Bluetooth stack is enabled. Refer to the MC9190-G
Integrator Guide of Motorola for information on selecting the Bluetooth stack.
To determine the BTExplorer software version:
On Mobile 6.5, tab Start > BTExplorer > Menu > About.
6.4
Fusion Version
To determine the Fusion software version:
On Mobile 6.5, tab Start > Wireless Companion > Wireless Status > Versions.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 35 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Trouble Shooting
7
Trouble shooting
Caution!
If you have any problems with the MC 9190ex-NI, bring the device into a safe area first
before you try to remedy the fault.
Notes on Troubleshooting can be found in the user manual or Integrator Guide from
Motorola http://www.motorola.com/web/Business/CT/Enterprise+Mobility.htm on the
Motorola homepage.
The Motorola page for the MC9190-G manuals for the non-explosion-proof version
−
Support
−
Product Manuals
−
Mobile Computers
−
MC9190-G
−
Click on “More” for a complete list.
If you have problems with your device, please contact the BARTEC sales company or
commercial representation responsible for your region. You can find contact information
under:
http://www.bartec.de/homepage/eng/10_unternehmen/10_unternehmen/s_10_10_50.asp?C=1
7.1
Battery Management
Observe the following battery saving tips:
7.1.1
−
Leave the MC 9190ex-NI connected to AC power at all times when not in use.
−
Set the MC 9190ex-NI to turn off after a short period of non-use.
−
Set the display to turn off or dim backlight.
−
Set the keyboard backlight to turn off after a short period of non-use.
−
Turn off all wireless radio activity when not in use.
−
Power off the MC 9190ex-NI when charging to charge at a faster rate.
Changing the Power Settings
To set the MC 9190ex-NI to turn off after a short period of non-use:
1. On devices with Windows Mobile 6.5, tap Start > Settings > System > Power >
Advanced.
2. Select the On battery power: Turn off device if not used for: check box and select
a value from the drop-down list box.
3. Tap OK.
Page 36 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
7.1.2
Trouble Shooting
Changing the Backlight Settings
To change the display backlight settings in order to conserve more battery power:
1. On devices with Windows Mobile 6.5, tap Start > Settings > System > Backlight >
Battery Power.
2. Select the On battery power: Disable backlight if not used for: check box and
select a value from the drop-down list box.
3. Tap the Brightness tab.
4. Tap the Disable backlight check box to completely turn off the display backlight.
5. Use the slider to set the brightness of the backlight. Set it to a low value to save
battery power.
6. Tap OK.
7.1.3
Changing the Keypad Backlight Settings
To change the keypad backlight settings in order to conserve more battery power:
1. On devices with Windows Mobile 6.5, tap Start > Settings > System > Keylight >
Battery Power.
2. Select the On Battery Power: Disable keylight if not used for: check box and
select a value from the drop-down list box.
3. Tap Advanced.
4. Tap the Disable keylight check box to completely turn off the display backlight.
5. Tap OK.
7.1.4
Changing the settings for the display backlight
This is how you change the settings for the display backlight to save battery power:
1. Tap on Start > Settings > Tab System > Symbol Backlight > Tab Battery Power.
2. Activate the control box Disable backlight if device is not used for, and select a
value from the Dropdown List.
3. Select the Tab Brightness.
4. Tap on the control box Disable backlight, to switch off the display backlight, or use
the slider to set a lower value for the display backlight.
5. Tap on OK.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 37 of 50
Trouble Shooting
7.1.5
Turning Off the Radios
Note
7.1.6
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Wireless connection options vary depending upon configurations.
On Devices with Mobile 6.5
Windows Mobile 6.5 devices include Wireless Manager, which provides a simple method
of enabling, disabling, and configuring all the device’s wireless capabilities in one place.
1. To open Wireless Manager, tap the Status Bar and then the Connectivity icon and
select Wireless Manager.
or tap Start > Settings > Connections > Wireless.
2. To enable or disable a wireless connection, tap its blue bar.
3. To enable or disable all wireless connections, tap and hold the All bar.
4. To configure settings for a connection, tap Menu.
Page 38 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
7.2
Trouble Shooting
Resetting the MC 9190ex-NI
There are several reset functions, warm boot, cold boot and clean boot.
7.2.1
−
A warm boot restarts the MC 9190ex-NI by closing all running programs.
−
A cold boot also restarts the MC 9190ex-NI, but erases all stored records and entries
in RAM. Data saved in flash memory or a memory card is not lost. In addition it
returns formats, preferences and other settings to the factory default settings.
Perform a warm boot first. This restarts the MC 9190ex-NI and saves all stored
records and entries. If the MC 9190ex-NI still does not respond, perform a cold boot.
−
A clean boot resets the MC 9190ex-NI to the factory default settings. All data in the
Application folder is retained. You must download the Clean Boot Package file from
the Support Central web site by Motorola
On a Windows Mobile 6.5 device
Note
There are three reset functions, warm boot, cold boot and clean boot.
1. A warm boot restarts the MC 9190ex-NI and closes all running programs.
2. A cold boot also restarts the MC 9190ex-NI and closes all running programs but also
resets the Real-Time-Clock (RTC).
3. A clean boot resets the MC 9190ex-NI to the factory default settings.
Caution!
Do not hold down any key, other than the Power button during a reset. Performing a
cold boot restores formats, preferences and other settings to the default settings.
Any data previously synchronized with a computer can be restored during the next
ActiveSync operation.
Note
Data saved in flash memory or a memory card is not lost. Perform a warm boot first.
This restarts the MC 9190ex-NI and saves all stored records and entries. If the
MC 9190ex-NI still does not respond, perform a cold boot.
7.2.2
Warm boot
Executing a warm boot
Hold down the Power button for approximately five seconds. As soon as the
MC 9190ex-NI starts to perform a warm boot release the Power button.
7.2.3
Cold Boot
Executing a cold boot
A cold boot restarts the MC 9190ex-NI and erases all user stored records and entries that
are not saved in flash memory (Application and Platform folders) or a memory card. Never
perform a cold boot unless a warm boot does not solve the problem.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 39 of 50
Trouble Shooting
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
To perform a cold boot:
1. Press the primary battery release on the MC 9190ex-NI to partially eject the battery
from the MC 9190ex-NI. (described in chapter 4.4.3 Replacing a battery)
2. While the battery is partially released, simultaneously press and release the handle
trigger and the Power button.
3. Push the battery to fully re-insert it in the MC 9190ex-NI. One audible click can be
heard as the battery is fully inserted.
4. The MC 9190ex-NI initializes.
5. Calibrate the screen. See Calibrating the Screen in the Motorola User Guide to
calibrate the MC 9190ex-NI screen.
7.2.4
Clean Boot
Caution!
A clean boot should only be performed by an authorized system administrator. You
must connect the MC 9190ex-NI to AC power during a clean boot. Removing AC power
from the MC 9190ex-NI during a clean boot may render the MC 9190ex-NI inoperable.
A clean boot resets the MC 9190ex-NI to the factory default settings. All data in the
Application folder is retained. You must download the Clean Boot Package file from the
Support Central web site by Motorola
1. Download the Clean Boot Package from the Motorola Support Central. Follow the
instructions included in the package for installing the package onto the
MC 9190ex-NI.
2. Press the primary battery release on the MC 9190ex-NI to partially eject the battery
from the MC 9190ex-NI. (described in chapter 4.4.3 Replacing a battery)
3. While the battery is partially released, simultaneously press and release the trigger
and the Power button.
Note
After you insert the battery you have two seconds to press the trigger or left scan
button.
4. Push the battery to fully re-insert it in the MC 9190ex-NI. One audible click can be
heard as the battery is fully inserted.
5. Press and hold the trigger.
6. Connect the MC 9190ex-NI to AC power using the CAM or insert the MC 9190ex-NI
into a powered cradle.
7. The MC 9190ex-NI updates and then re-boots.
8. The calibration screen appears.
Page 40 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
8
Maintenance, Inspection,
Repair
Maintenance, Inspection, Repair
This chapter describes cleaning and storing the MC 9190ex-NI, as well as possible
procedures when problems occur while using the MC 9190ex-NI.
When doing maintenance or servicing or when checking associated equipment, comply
with the applicable regulations in accordance with directives IEC 60079-19 and
IEC 60079-17!
Caution!
Installation/dismantling, operating and maintenance work may be carried out by trained
specialists only. Statutory regulations and other binding directives on workplace safety,
accident prevention and environmental protection must be adhered to.
You should heed the following tips when using the MC 9190ex-NI to guarantee fault-free
operation:
−
Pay attention that the MC 9190ex-NI display is not scratched. When working with the
MC 9190ex-NI use the supplied stylus or pens with plastic tip which are designed for
use with touch screens. Never use a ballpoint pen, pencils or other pointed items on
the MC 9190ex-NI screen. BARTEC recommends using a screen protector, Part no.
17-A1Z0-0003.
−
The touch-sensitive screen of the MC 9190ex-NI contains glass. Take care not to drop
the MC 9190ex-NI or subject it to strong impact.
−
Protect the MC9190ex-NI against extreme temperatures. Do not leave it on the
dashboard of the car on hot days and keep it away from heat sources.
−
Do not store the MC 9190ex-NI in dusty, moist or wet environments.
−
Use a soft spectacle cleaning cloth to clean the MC 9190ex-NI. If the MC 9190ex-NI
display surface is dirty, clean it with a soft spectacle cleaning cloth soaked in diluted
window cleaner.
−
Change the re-chargeable battery regularly to ensure maximum battery life and
equipment performance. Battery life depends on the individual usage pattern. The
battery provides a state display to estimate the remaining life. You can find further
information in chapter 4.4 “Battery”.
−
Pay attention that the scan window is not scratched. Clean the window regularly.
Dust, contaminants and scratches on the scan window can lead to visible spots on
the pictures taken with the scanner.
−
The battery should be completely charged before it is used for the first time. Note that
the maximum capacity of the battery is not attained until after approx. 5-6 charging
and discharging cycles.
−
For the MC 9190ex-NI is a screen protector available. BARTEC recommends using
this, to avoid wear marks. A screen protector contributes to the user friendliness of
the equipment and protects the touch screen.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 41 of 50
Maintenance, Inspection,
Repair
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
−
8.1
Protection against scratches and dents
Resistant and non-slip writing and touch screen surface
Protection against abrasion and chemicals
Reflection reduction
Equipment screen always looks brand new
Simple and quick installation
−
As the battery power diminishes over the course of time, the batteries should be
completely discharged and recharged every now and then in order to retain the full
capacity. For that purpose the devices are left switched on until the devices switch off
themselves. Then recharge the battery completely outside the Ex area.
−
Before a lengthy idle time it is essential to charge the battery completely and to
recharge it regularly (every 3 months).
In accordance with IEC 60079-19 and IEC 60079-17, the owner-operator of the
electrical installations in potentially explosive areas has an obligation to have these
installations checked by a qualified electrician to ensure that they are in a proper
condition.
Inspection
Caution!
8.3
■
■
■
■
■
■
Servicing
Caution!
8.2
The advantages at a glance:
Repairs on explosion-protected operating equipment may be done only by authorised
persons using original spare parts and working in accordance with the latest
developments of technology. The relevant applicable regulations must be observed.
Please direct any questions you may have to BARTEC GmbH.
Cleaning
If you wish to clean the MC 9190ex-NI or components, take the device out of the Ex
area first before you start any cleaning measures.
Caution!
Attention!
Page 42 of 50
Always wear eye protection.
Read warning label on compressed air and alcohol product before using.
Avoid exposing this product to contact with hot oil or other flammable liquids. If such
exposure occurs, unplug the device and clean the product immediately in accordance
with these guidelines.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Maintenance, Inspection,
Repair
Approved Cleanser Active Ingredients
100% of the active ingredients in any cleaner must consist of one or some combination of
the following: isopropyl alcohol, bleach/sodium hypochlorite, hydrogen peroxide or mild
dish soap.
Harmful Ingredients
The following chemicals are known to damage the plastics on the MC 9190ex-NI and
should not come in contact with the device: ammonia solutions, compounds of amines or
ammonia; acetone; ketone; ethers; aromatic and chlorinated hydrocarbons; aqueous or
alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic
acid and TB-lysol form.
Cleaning Instructions
Do not apply liquid directly to the MC 9190ex-NI. Dampen a soft cloth or use premoistened wipes. Do not wrap the device in the cloth or wipe, but gently wipe the unit. Be
careful not to let liquid pool around the display window or other places. Allow the unit to air
dry before use.
Special Cleaning Notes
Many vinyl gloves contain phthalate additives, which are often not recommended for
medical use and are known to be harmful to the housing of the MC 9190ex-NI. The
MC 9190ex-NI should not be handled while wearing vinyl gloves containing phthalates, or
before hands are washed to remove contaminant residue after gloves are removed. If
products containing any of the harmful ingredients listed above are used prior to handling
the MC 9190ex-NI, such as hand sanitizer that contain ethanolamine, hands must be
completely dry before handling the MC 9190ex-NI to prevent damage to the plastics.
8.3.1
8.3.2
Required materials
−
Alcohol cleaning wipes
−
Lens cleaning wipes
−
Cleaning cotton buds
−
Isopropyl alcohol
−
Compressed air spray with hose.
Housing
Using the alcohol wipes, wipe the housing including keys and in-between keys.
8.3.3
Display
The display can be wiped down with the alcohol wipes, but care should be taken not to
allow any pooling of liquid around the edges of the display. Immediately dry the display
with a soft, non-abrasive cloth to prevent streaking.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 43 of 50
Maintenance, Inspection,
Repair
8.3.4
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Scan window
Wipe the scanner exit window periodically with a lens tissue or other material suitable for
cleaning optical material such as eyeglasses.
8.3.5
Interface connection
Attention!
(1)
Remove the main battery from the MC 9190ex-NI.
(2)
Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol.
(3)
Rub the cotton portion of the cotton tipped applicator back-and-forth across the
connector on the bottom of the MC 9190ex-NI. Do not leave any cotton residue on
the connector.
(4)
Repeat at least three times.
(5)
Use the cotton tipped applicator dipped in alcohol to remove any grease and dirt
near the connector area.
(6)
Use a dry cotton tipped applicator and repeat steps 4 through 6.
(7)
Spray compressed air on the connector area by pointing the tube/nozzle about ½
inch away from the surface.
Do not direct the nozzle onto yourself or other persons. Pay attention that the nozzle
does not point towards your face.
(8)
8.3.6
Cradle/Battery contacts
Attention!
Page 44 of 50
Inspect the area for any grease or dirt, repeat if required.
(1)
Remove the DC power cable from the cradle.
(2)
Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol.
(3)
Rub the cotton portion of the cotton tipped applicator along the pins of the
connector. Slowly move the applicator back-and-forth from one side of the
connector to the other. Do not let any cotton residue on the connector.
(4)
All sides of the connector should also be rubbed with the cotton tipped applicator.
(5)
Spray compressed air in the connector area by pointing the tube/nozzle about ½
inch away from the surface.
Do not direct the nozzle onto yourself or other persons. Pay attention that the nozzle
does not point towards your face.
(6)
Ensure that there is no lint left by the cotton tipped applicator, remove lint if found.
(7)
If grease and other dirt can be found on other areas of the cradle, use lint free cloth
and alcohol to remove.
(8)
Allow at least 10 to 30 minutes (depending on ambient temperature and humidity)
for the alcohol to air dry before applying power to cradle. If the temperature is low
and humidity is high, longer drying time is required. Warm temperature and dry
humidity requires less drying time.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Maintenance, Inspection,
Repair
Cleaning the charging station plug-connectors
This is how you clean the plug-connectors of a charging station:
Attention!
8.3.7
(1)
Separate the DC power supply cable from the charging station.
(2)
Dip the end of a cotton bud in Isopropyl.
(3)
Rub over the contacts of the plug-connector(s) with the tip of the cotton bud. Move
the cotton bud slowly from one side of the plug-connector to the other and back
again. Pay attention that that no cotton residue remains on the plug-connectors.
(4)
All of the plug-connector sides should also be cleaned with the help of the cotton
bud.
(5)
Spray compressed air onto the plug-connector area and keep the hose, resp. the
nozzle about 15 mm above the surface.
Do not direct the nozzle onto yourself or other persons. Pay attention that the nozzle
does not point towards your face.
(6)
Make sure that no lint remains from the cotton buds and remove any lint.
(7)
If there are any grease and dirt deposits on other sectors of the charging station,
remove this with a lint-free cloth and alcohol.
(8)
Allow the alcohol to dry at least 10 to 30 minutes in the air (depending on the
ambient temperature and humidity) before you connect the charging station to the
power source. The required drying time increases with lower temperature and high
humidity. The required drying time decreases with higher temperature and lower
humidity.
Cleaning interval
The cleaning frequency is up to the customer’s discretion due to the varied environments
in which the mobile devices are used. They may be cleaned as frequently as required.
However when used in dirty environments it may be advisable to periodically clean the
scanner exit window to ensure optimum scanning performance.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 45 of 50
Maintenance, Inspection,
Repair
8.4
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Information about Repairs
Customer Service Information
If you have problems with your device, please contact the BARTEC sales company or
commercial representation responsible for your region. You can find contact information
under:
http://www.bartec.de/homepage/eng/10_unternehmen/10_unternehmen/s_10_10_50.asp?C=1
Please have the following information available when you contact BARTEC:
−
Serial number of the device (you can find this on the manufacturer label)
−
Model number or product name (you can find these on the manufacturer label)
−
Software type and version number
Manufacturer label
BARTEC answers enquiries by email, telephone or fax. If the problem cannot be
rectified by the BARTEC sales companies or commercial representations, you may
need to return the device to us for maintenance.
If you wish to send in a defective device for repairs please first read the RMA procedure
guide. Then fill in and sign the RMA (Return Merchandise Authorisation) form and send
it to our "Retouren Centre".
Email:
Fax:
services@bartec.de
+49 7931 597-119
We cannot guarantee any contractually agreed processing times for devices that are
sent in without an RMA number.
The RMA guide and the RMA form are available on our homepage for downloading.
http://www.bartec-group.com
Quality and Culture
RMA Form
Any questions? Send us an e-mail or call us.
E-mail:
Phone:
Page 46 of 50
services@bartec.de
+49 7931 597-444
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
9
Accessories
9.1
Accessories for use in hazardous area
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Accessories
Page 47 of 50
Accessories
9.2
Page 48 of 50
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Accessories for use in non hazardous area
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Additional Information
10
Order Numbers
10.1
MC 9190ex-NI
11
Disposal
The component of the Mobile Computers contains metal, plastic parts and electronic
components.
The statutory requirements for electrical scrap must be observed therefore (e.g. disposal
by an approved disposal company).
12
Dispatch and Packaging Instructions
Important information regarding transport and dispatch
! Sensitive Devices!
It is absolutely necessary to deliver the equipment in
the original packaging in order to avoid damage to the
equipment.
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Page 49 of 50
Order Numbers, Disposal,
Dispatch and Packaging
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
13
Additional Information
13.1
Links
http://www.bartec-group.com
BARTEC Homepage
http://www.motorola.com/web/Business/CT/Enterprise+Mobility.htm
Motorola Homepage
The Motorola page for the MC9190 User Manuals of the non-explosion protected version





Support
Product Manuals
Mobile Computers
MC 9190-G
Click on “More” for complete list
The Motorola page for the MC9190 software of the non-explosion protected version






Support
Enterprise Mobility
=> Download Software
Software Download
Mobile Computers
MC 9190-G
Click on “More” for complete list
http://www.motorolasolutions.com/US-EN/Home
The Motorola product information page for the MC9190 of the non-explosion protected version
Products
Mobile Computers
Handheld Computers
MC9190-G Mobile Computer
http://www.motorolasolutions.com/US-EN/Home
The Motorola page for the Scan Engine which is used in the MC9190ex-NI series.



Products
OEM Products
OEM Scan Engines
https://devcentral.motorola.com/login.aspx?p=/Default.aspx
The Motorola Developer Central page for software developers.
Tools, Updates, Patches etc. or the individual symbol products can be found on this page.
It is necessary to register to get access to the pages. Registration is free of charge.
http://www.microsoft.com
Microsoft Site for Active Sync or Windows Mobile Device Center for Windows Vista and Windows 7
Page 50 of 50
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Declaration of Conformity
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Appendix
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Technical data subject to change without notice.
Issue: Revision 1 / March 2011
Certificate of Compliance
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Mobile Computer MC 9190ex-NI
Type B7-A28.-…………
Technical data subject to change without notice.
Issue: Revision 2 / August 2012
Certificate of Compliance
BARTEC protects
people
and
the environment
by the safety
of components,
s y s t e m s
BARTEC GmbH
Germany
plants.
Max-Eyth-Straße 16
97980 Bad Mergentheim
Phone: +49 7931 597-0
Fax:
+49 7931 597-119
info@bartec.de
www.bartec-group.com
B1-A280-7D0001-April 2011
and