- Home
- Home security & automation
- Security access control systems
- Interlogix
- TVD-3104
- Installation Guide
advertisement
TruVision IP Camera
Installation Guide
P/N 1072668A-EN • REV 1.0 • ISS 24SEP13
Copyright © 2013 UTC Fire & Security Americas Corporation,
Inc.
Trademarks and patents
Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved.
The TruVision name and logo are trademarks of United
Technologies.
Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Manufacturer UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923,
USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
ACMA compliance Notice! This is a Class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
Canada This Class A digital apparatus complies with Canadian
ICES-003.
European Union directives
Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du Canada.
12004/108/EC (EMC directive): Hereby, UTC Fire &
Security declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Contact information For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu.
Content
Introduction 6
Product overview 6
Installation 7
Installation environment 7
Package contents 8
Cable requirements 8
Camera description 9
Setting up the camera 12
Accessing the SD card 13
Mounting the bullet camera 13
Mounting the VF dome camera 15
Mounting the indoor mini dome camera 19
Mounting the wedge dome camera 21
Using the camera with an Interlogix NVR or Hybrid DVR or another system 22
Using the camera with TruVision Navigator 22
Specifications 23
TruVision IP bullet cameras 23
TruVision IP indoor mini dome 23
TruVision IP wedge cameras 24
TruVision IP VF mini dome cameras 24
Pin definitions 25
Installation Guide 5
Introduction
Product overview
This is the installation guide for TruVision IP camera models:
TVB-1101 (1.3MPX IP bullet camera, PAL)
TVB-3101
TVB-1102
(1.3MPX IP bullet camera, NTSC)
(3MPX IP bullet camera, PAL)
TVB-3102
TVD-1103
TVD-3103
TVD-1104
(3MPX IP bullet camera, NTSC)
(1.3MPX IP VF mini dome, PAL)
(1.3MPX IP VF mini dome, NTSC)
(3MPX IP VF mini dome, PAL)
TVD-3104
TVD-1101
TVD-3101
TVD-1102
TVD-3102
TVW-1101
TVW-3101
TVW-1102
TVW-3102
(3MPX IP VF mini dome, NTSC)
(1.3MPX IP indoor mini dome, PAL)
(1.3MPX IP indoor mini dome, NTSC)
(3MPX IP indoor mini dome, PAL)
(3MPX IP indoor mini dome, NTSC)
(1.3MPX IP wedge dome, PAL)
(1.3MPX IP wedge dome, NTSC)
(3MPX IP wedge dome, PAL)
(3MPX IP wedge dome, NTSC)
Installation
This section provides information on how to install the cameras.
Installation environment
When installing your product, consider these factors:
• Electrical: Install electrical wiring carefully. It should be done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified power supply to power the camera. Do not overload the power cord or adapter.
•
•
Ventilation: Ensure that the location planned for the installation of the camera is well ventilated.
Temperature: Do not operate the camera beyond the specified temperature, humidity or power source ratings.
The operating temperature of the camera is between -30 to +60°C (-22 to 140°F). Humidity is below 90%.
•
•
•
Moisture: Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately if the camera is wet and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock.
Servicing: Do not attempt to service this camera yourself. Any attempt to dismantle or remove the covers from this product will invalidate the warranty and may also result in serious injury. Refer all servicing to qualified service personnel.
Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some ethanol and wipe the camera gently. If the camera will not
Installation Guide 7
be used for an extended period of time, put on the lens cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit; contact the supplier immediately. If the unit is returned, it must be shipped back in its original packaging.
Package contents:
Camera
Hex wrench (for dome and mini dome cameras only)
CD with Configuration manual and TruVision Device
Finder
CAUTION: Use direct plug-in UL listed power supplies marked Class 2/CE certified or LPS (limited power source) of the required output rating as listed on the unit.
Cable requirements
For proper operation, adhere to the following cable and power requirements for the cameras. Category 5 cabling or better is recommended. All network cabling must be installed according to applicable codes and regulations.
Table 1 on page 9 lists the requirements for the cables that connect to the camera.
Table 1: Recommended power cable requirements
Bullet camera:
Mini dome:
Wedge camera:
VF dome camera:
12 VDC power jack or PoE (802.3af)
PoE (802.3af)
12 VDC power jack or PoE (802.3af)
12 VDC power jack or PoE (802.3af)
Camera description
Figure 1: IP bullet camera
Adjustable bracket
Sun shield
Housing
Grounding screws
Reset button
Installation Guide 9
Figure 2: IP indoor mini dome camera
1. Base
2. Lens
4. Housing
5. Ethernet RJ45 and BNC cable
6. Safety cable
Figure 3: IP wedge camera
1
2
6
3 7
4
5
1. Cover
2. Lens
3. SD card
4. Ethernet RJ45 PoE port
5. Power supply
6. Base
7. Serial port
8. Reset button
9. Converter pan
8
9
Installation Guide 11
Figure 4: IP VF dome camera
1. Dome liner
2. Housing
3. Ethernet RJ45 PoE port
4. Power supply
5. Audio and alarm cables
6. Lens
7. Mounting plate
8. Reset button
9. Analog video output
10. Serial port
11. SD card
Setting up the camera
Note: If the light source where the camera is installed experiences rapid, wide- variations in lighting, the camera may not operate as intended.
To quickly put the camera into operation:
1. Prepare the mounting surface.
2 Mount the camera on the ceiling using the appropriate fasteners. See “Mounting the bullet camera” on page 13.
3. Set up the camera’s network and streaming parameters so that the camera can be controlled over the network.
For further information, please refer to the “TruVision IP
Camera Configuration Manual”.
4. Program the camera to suit its location. For further information, please refer to the “TruVision IP Camera
Configuration Manual”.
Accessing the SD card
Insert a Micro SD card with up to 64GB for local storage as a backup in case, for example, the network fails (see Figure 1 on page 9). The card is not supplied with the camera.
For the IP VF dome camera, point the lens vertically upwards to access the SD card slot.
Video and log files stored on the Micro SD card can only be accessed via the web browser. You cannot access the card using TruVision Navigator or a recording device.
Note: There is no Micro SD card slot in the bullet and indoor mini dome cameras.
Mounting the bullet camera
Mount the camera on a ceiling or wall.
To mount the bullet camera:
1. Use the supplied template to mark out the mounting area.
Drill the screw holes on the ceiling or wall. If you need to route the cables from the camera base, cut a cable hole in the ceiling or wall.
Installation Guide 13
Hole
Ceiling Mounting
Hole
Hole
2. Secure the mounting base to the ceiling or wall with the supplied screws.
3. Loosen the adjustable nuts on the bracket, and adjust the camera from P/R/T (pan/rotate/tilt) direction.
P Direction: 0 to 360°adjustable.
T Direction: 0 to 90°adjustable.
R Direction: 0 to 360°adjustable
Adjust the lens to the required surveillance angle. Tighten the adjustable nuts to complete the installation.
0° ~ 3 6 0°
0° ~ 3 6 0°
0°~ 9 0°
Mounting the VF dome camera
To mount the VF dome camera on a ceiling or wall:
1. Loosen the three screws on the edge of the lower dome with screw driver.
Screws
2. Open the lower dome and remove the black inner liner.
Installation Guide 15
3. Drill the three screw holes on the ceiling with the supplied drill template.
Cable hole
Screw holes
4. If you want to route the cables inside the ceiling, drill a cable hole in the ceiling or wall using the drill template.
5. Attach the camera to the ceiling or wall by aligning the housing holes with those in the ceiling. Secure the camera with the supplied screws as shown below.
6. Route the cables through the cable hole.
Note: If required, you can route cables through the side screw opening of the camera
7. Connect the video output connector to the monitor.
Connect the power connector to the power supply.
8. Adjust the image and focus.
View the camera image using the monitor. Hold the panning table and pull out slightly to adjust the
Installation Guide 17
panning position of the camera. Rotate the tilting axes to adjust the tilting position of the camera.
Rotate the lens table to adjust the azimuth angle of the image.
2) Zoom and focus adjustment.
Loosen the zoom lever and move the lever between
T(Tele) and W(Wide) to obtain the appropriate angle of view.
3) Tighten the zoom lever.
Loosen the focus lever and move the lever between
F(Far) and N(Near) to obtain the optimum focus.
Tighten the focus lever.
Rotation
Tilting
Rotation
Mounting the indoor mini dome camera
To mount the indoor mini dome camera on a ceiling:
1. Drill the screw holes on the ceiling with the supplied drilling template. If you need to route the cables from the bottom of the camera, cut a cable hole in the ceiling.
1
1
1
2. Using the supplied hex wrench, loosen the set screws to remove the dome enclosure.
3. Fix the mounting base onto the ceiling with screws.
Installation Guide 19
Note: If required, you can route cables through the side opening of the mounting base.
4. Loosen the tilt lock screws, and adjust the tilting position in a range of 65 degrees. Retighten the tilt lock screws.
Rotate the dome liner to adjust the panning position in a range of 360 degrees to obtain the desired surveillance angle.
Adjust screw
5. Reinstall the lower dome and tighten the screws.
Mounting the wedge dome camera
To mount the wedge dome camera on a ceiling:
1. Drill the screw holes on the ceiling with the supplied drilling template. To route the cables from the base of the camera, cut a cable hole in the ceiling.
2. Fix the converter pan to the ceiling (optional).
Note: If required, you can remove the tabs (A) on the side of the converter pan to pass the cables through.
3. Loosen the set screws with a hex wrench (supplied) to remove the dome enclosure.
Installation Guide 21
4. Fix the camera base to the converter pan or mounting surface.
5. Re-attach the dome enclosure to the camera.
Using the camera with an Interlogix NVR or Hybrid DVR or another system
Please refer to the NVR/DVR user manuals for instructions on connecting and operating the camera with these systems.
Using the camera with TruVision
Navigator
A camera must be connected to an Interlogix NVR or hybrid
DVR in order to be operated by TruVision Navigator. Please refer to the TruVision Navigator user manual for instructions on operating the camera with the TruVision Navigator.
Specifications
TruVision IP bullet cameras
Electrical
Voltage input
Power consumption
Miscellaneous
Connectors
Operating temperature
Dimensions
Weight
Environmental rating
12 VDC, PoE (IEEE 802.3af)
Max. 5 W
DC jack flying lead, RJ45 flying lead
-30 to 60 °C (-22 to 140°F)
Φ 60 × 153 mm (2.3” × 6.0”)
373 g (0.82 lbs)
IP66
TruVision IP indoor mini dome
Electrical
Voltage input
Power consumption
Miscellaneous
PoE (IEEE 802.3af)
Max. 5 W
Connectors
Operating temperature
RJ45 flying lead
-30 to +60 °C (-22 to +140 °F)
Dimensions (L × W × H) Φ 111 × 82 mm (4.4” × 3.2”)
Weight 370 g (0.81lbs)
Installation Guide 23
TruVision IP wedge cameras
Electrical
Voltage input 12 VDC, PoE (IEEE 802.3af)
Power consumption
Miscellaneous
Max. 5 W (Max. 7 W with IR on)
Connectors DC jack flying lead, RJ45 flying lead
Operating temperature -30 to +60°C (-22°F to +140°F)
Dimensions (L × W × H) 98 × 89 × 329 mm
(3.86 ×3.49 × 12.94 in.)
Weight
Environmental rating
407 g (0.89 lb)
IP66
TruVision IP VF mini dome cameras
Electrical
Voltage input 12 VDC, PoE (IEEE 802.3af)
Max. 5.5 W Power consumption
Miscellaneous
Connectors
Operating temperature
Dimensions (L × W ×
H)
Weight
Environmental rating
DC jack flying lead, RJ45 flying lead
-30 to +60°C (-22°F to 140°F)
Φ 140 × 100 mm (Φ 5.51” ×
3.94”)
767 g (1.69 lb)
IP66
Pin definitions
There are eight wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight and crossover cable connection:
Figure 3: Straight-through cable
1 White/Orange
2 Orange
3 White-Green
4 Blue
5 White/Blue
6 Green
7 White/Brown
8 Brown
Figure 4: Cross-over cable
1 White/Orange
2 Orange
3 White-Green
4 Blue
5 White/Blue
6 Green
7 White/Brown
8 Brown
White/Orange
1
Installation Guide 25
Please make sure your connected cables have the same pin assignment and color as above before deploying the cables in your network.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project