INFORMACIÓN ADICIONAL
Especificaciones
Generalidades
Potencia de salida RMS mínima por canal
........... 55 W + 55 W (6Ω 1kHz distorsión armónica total del 0,1%)
..... 40 W + 40 W (6Ω 20 Hz a 20 kHz distorsión armónica total del 0,1%)
Potencia de salida estándar DIN por canal (Modelo para el Europa)
........... 60 W + 60 W (4Ω 1kHz distorsión armónica total del 0,7%)
Sensibilidad de entrada/impedancia
DVD/TAPE/MD/AUX .............................................. 150 mV/47 kΩ
Respuesta de frecuencia
DVD etc. .................................................... 20 Hz a 20 kHz, ±0,5 dB
Distorsión armónica total (20 Hz a 20 kHz)
DVD etc. 20 W, 6 Ω ................................................................ 0,04%
Relación de señal-ruido (Red A de IHF)
DVD etc. (250 mV, Entrada contocircuitada) ......................... 98 dB
Nivel/impedancia de salida
PHONES ..................................................................... 0,43 V/330 Ω
Alimentación
[Modelos para los EE UU y Canadá] .................... CA 120 V, 60 Hz
[Modelo para Australia] ........................................ CA 240 V, 50 Hz
[Modelos para Reino Unido y Europa] ................. CA 230 V, 50 Hz
[Modelos para Asia y modelos en general]
............................................. CA 110/120/220/230-240 V, 50/60 Hz
[Modelo para Corea] ............................................. CA 220 V, 60 Hz
Consumo
[Modelos para los EE UU y Canadá] ..................................... 110 W
[Otros modelos] ...................................................................... 125 W
Consumo (modo de espera)
[Modelos para los EE UU y Canadá] ...................................... 0,7 W
[Otros modelos] ....................................................................... 0,8 W
Dimensiones (An x Al x Prof) .......................... 217 x 108 x 372 mm
Peso ......................................................................................... 5,4 kg
Sección del sintonizador
RX-E600
RX-E600
Sección del amplificador
Receiver
Récepteur
Las especificaciones están sujetas a cambios sin previo aviso.
Gama de sintonización
FM
[Modelos para los EE UU y Canadá] ................... 87,5 – 107,9 MHz
[Modelos para Reino Unido, Europa, Australia y Corea]
.......................................................................... 87,50 – 108,00 MHz
[Modelos para Asia y modelos en general]
....................................................... 87,5/87,50 – 108,0/108,00 MHz
AM
[Modelos para los EE UU y Canadá] ...................... 530 – 1710 kHz
[Modelos para Reino Unido, Europa, Australia y Corea]
................................................................................. 531 – 1611 kHz
[Modelos para Asia y modelos en general]
................................................................. 530/531 – 1710/1611 kHz
Sensibilidad
FM (Relación señal a ruido de 30 dB) ................................... 1,0 µV
AM .................................................................................... 300 µV/m
©2004
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
0101RXE600_EB_H1.p65
1
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
All rights reserved.
Printed in Malaysia
WD90150
2004.08.16, 18:01
CAUTION: READ THIS BEFORE OPERATING THIS UNIT
1
2
3
4
5
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a well ventilated, cool, dry, clean
place away from direct sunlight, heat sources, vibration,
dust, moisture or cold. In a cabinet, allow about 10 cm
(4 in.) of free space all around RX-E600 for adequate
ventilation.
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause
an electrical shock, fire, damage to this unit, and/or
personal injury.
Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of
this unit, do not place:
• Other components, as they may cause damage and/or
discoloration on the surface of this unit.
• Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
• Containers with liquid in them, as they may fall, spilling
the liquid and causing an electrical shock to the user
and/or damage to this unit.
6
7
8
9
10
11
12
13
14
15
16
17
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use excessive force on switches, knobs and/or
cords.
When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Use only the voltage specified on this unit. Using this
unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than as specified.
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reason.
When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
Be sure to read the “Troubleshooting” section on
common operating errors before concluding that this
unit is faulty.
Before moving this unit, press STANDBY/ON to set the
unit in standby mode, then disconnect the AC power
plug from the wall outlet.
18
VOLTAGE SELECTOR (General model only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging into the AC main supply. Voltages are 110/120/
220/230-240 V AC, 50/60 Hz.
To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wires in the mains lead are coloured in accordance
with the following code:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured BLUE
must be connected to the terminal which is marked
with the letter N or coloured BLACK. The wire which
is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described above.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
(U.S.A., Canada and General models)
The nameplate is located on the bottom of the unit.
FEATURES
English
• Minimum RMS output power per
channel 40 W + 40 W
(6Ω, 20 Hz to 20 kHz, 0.1% THD)
• System remote control
• 40-station FM/AM preset tuning
• Multi-function RDS reception
• SUBWOOFER output terminal
The receiver (RX-E600) and DVD player (DVD-E600) are the main units of the YAMAHA Piano Craft Series.
You can upgrade the system by adding the cassette deck (KX-E300) and MD recorder (MDX-E300)*.
* MD recorder (MDX-E300) may not be available for some areas.
CONTENTS
SUPPLIED ACCESSORIES ....................... 2
GETTING STARTED
Remote control .................................................... 3
Connecting the speakers and antennas ................ 4
Connecting the system ......................................... 5
Setting the clock .................................................. 6
NAMES OF BUTTONS AND CONTROLS
Front panel ........................................................... 7
Display ................................................................. 7
Remote control .................................................... 8
BASIC OPERATIONS
Listening to a source............................................ 9
TUNING
Listening to the radio ......................................... 10
Presetting stations .............................................. 11
RECEIVING RDS STATIONS
Receiving RDS data .......................................... 12
PTY SEEK mode ............................................... 13
Optional settings for RDS functions ................. 14
USING THE BUILT-IN TIMER
Before using the timer ....................................... 15
Timer play and recording .................................. 15
Sleep timer ......................................................... 16
SYSTEM CONTROL
Controlling other components ........................... 17
Before recording ................................................ 19
Dubbing setting ................................................. 19
ADDITIONAL INFORMATION
Troubleshooting ................................................. 20
Specifications .................................................... 22
1
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
• AM loop antenna
• Remote control
POWER
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
B
C
TIME
D
E
TAPE
DIRECTION
PRESET
MD
TUNER
PRESET
DVD
TAPE
AUX
MD
REC/PAUSE
MODE
TAPE
REC/PAUSE
DUBBING
SLEEP
START
DISPLAY
VOLUME
• Batteries (AA, R6, UM-3)
2
• Indoor FM antenna
GETTING STARTED
Remote control operation range
English
Remote control
VOLUME
The remote control for the RX-E600 also controls the
DVD-E600 DVD player, KX-E300 cassette deck, and the
MDX-E300 MD recorder. Operating buttons for each unit
are explained on the pages below:
Receiver, RX-E600:
DVD player, DVD-E600:
Cassette deck, KX-E300:
MD recorder, MDX-E300:
NATURAL SOUND
STEREO RECEIVER
RX–E600
STANDBY/ON
TIMER
DISPLAY
MEMORY
AUTO/MAN'L
TIMER ADJ
TIMER
BASS
PRESET/TUNING
PRESET/BAND
HOUR
TREBLE
MIN
MIN
MAX
INPUT
BALANCE
PHONES
–
P.8
P.17
P.18
P.18
+
–
+
R
L
Remote control
sensor
Battery installation
1
Within approximately
6 m (20 feet)
3
30°
2
Remove the battery compartment cover.
ER
ER
W
6
6
3
3
3
PO
3
6
2
2
9
6
1
5
5
9
2
5
1
8
5
8
8
4
4
8
7
7
4
7
7
• Use only AA, R6, UM-3 batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
• Remove the batteries if the remote control will not be used for
an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
The remote control is shipped with a protection sheet to
prevent the surface from being scratched during
transportation.
When removing the sheet, first put adhesive tape on an
edge of the remote control so that the tape sticks to the
sheet. Then peel the sheet off with the tape.
4
Notes
Removing the protection sheet
W
If you find that the remote control must be used closer to
the main unit than usual, the batteries are weak. Replace
batteries with new ones.
PO
Battery replacement
2
Replace the battery compartment cover.
Notes
• There should be no large obstacles between the remote control
and the main unit.
• Strong light (especially light from inverter-type fluorescent
lamps etc) on the remote conrol sensor may impede the
functioning of the remote control. In this case, reposition the
main unit to avoid direct lighting.
1
Insert batteries into the battery compartment.
1
1
2
3
30°
Note
• Do not scratch the remote control surface when peeling the
sheet off.
3
GETTING STARTED
Connecting the speakers and antennas
Do not connect the AC power cord to the wall outlet until all connections have
been completed.
Follow the steps as shown below to connect the system using the supplied cords and accessories. Be sure all connections are
made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”.
Right speaker
3
Left speaker
FM antenna
2 AM loop antenna
C
IN
MD
DVD
OUT
SYSTEM
CONNECTOR
FM ANT
75Ω UNBAL.
D
A
R
IN
L
GND
TAPE
OUT
AM
ANT
B
+
–
E
IN
SUBWOOFER
OUT
SYSTEM
CONNECTOR
DVD
IN
6Ω MIN./SPEAKER
AUX
R
L
TUNER
SPEAKERS
4
1
1
Connect the Speakers.
1 Unscrew the knob.
2 Remove approx. 10 mm (0.4”) of insulation from
each of the speaker wires and insert the bare wire
into the terminal.
3 Tighten the knob to secure the wire.
Red: positive(+)
Black: negative(–)
2
Connect the AM Antenna.
Set up the AM loop antenna, then connect it.
Connect the FM Antenna.
FM ANT
75 Ω UNBAL
4
1
3
2
3
To wall outlet
Connect the AC power cord to a wall outlet.
Notes
• Use external FM/AM antennas if you need better reception.
Consult your dealer.
• The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
To connect the subwoofer (optional)
You can reinforce the bass frequencies by adding a
subwoofer (optional).
Connect the SUBWOOFER OUT terminal of the unit to
the INPUT terminal of the subwoofer.
GND
AM
ANT
4
GETTING STARTED
English
Connecting the system
Connecting the RX-E600 and the DVD-E600
1
2
3
Connect ‰ to ‰ using the Audio pin cable.
Insert the plugs into the jacks of the same color.
Connect the SYSTEM CONNECTOR (DVD) of the RX-E600 and the SYSTEM CONNECTOR (RECEIVER) of
the DVD-E600 with a system control cable (supplied with the DVD-E600).
*The other SYSTEM CONNECTOR of the RX-E600 is for connecting the MDX-E300 or KX-E300.
Connect the AC power plug of the DVD-E600 to AC OUTLET of the RX-E600.
This configuration allows you to turn all components in the system on and off with one touch, and reduces the standby
power consumption of the DVD-E600.
<RX-E600>
C
To wall outlet
IN
MD
DVD
OUT
SYSTEM
CONNECTOR
FM ANT
75Ω UNBAL.
D
A
R
IN
L
GND
TAPE
OUT
AM
ANT
B
+
–
E
IN
SUBWOOFER
OUT
SYSTEM
CONNECTOR
DVD
IN
6Ω MIN./SPEAKER
AUX
R
1
L
TUNER
SPEAKERS
Audio pin cable
*
2 System control cable
<DVD-E600>
SYSTEM
CONNECTOR
3
RECEIVER
COMPONENT VIDEO OUT
AV
To RX-E600
PR
PB
Y
DIGITAL
OUT
AUDIO
OUT
VIDEO OUT
L
VIDEO
R
S VIDEO
COAXIAL
OPTICAL
E
Adding KX-E300 and MDX-E300 to the above system
(For details, refer to the owner's manual supplied with the respective component.)
1
2
3
4
Connect Å and ı of RX-E600 to Å and ı of KX-E300.
Connect Ç and Î of RX-E600 to Ç and Î of MDX-E300.
Connect an external component to the AUX terminal of RX-E600.
Connect DIGITAL OPTICAL OUT of DVD-E600 to DIGITAL OPTICAL IN of MDX-E300.
Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL
IN jack before making digital connections. Be sure to replace the terminal’s cover when the terminal on the rear panel
is not being used, in order to protect from dust.
Caution
• Do not turn RX-E600 on until all connections between components have been completed.
• Do not connect or disconnect the system control cable and/or power cord while the system components are turned on.
5
GETTING STARTED
Setting the clock
You must set the clock before you use the timer functions.
The clock is based on a 24-hour system.
STANDBY/ON DISPLAY
HOUR MIN
VOLUME
NATURAL SOUND
STEREO RECEIVER
RX–E600
STANDBY/ON
TIMER
DISPLAY
MEMORY
AUTO/MAN'L
TIMER ADJ
TIMER
BASS
PRESET/BAND
PRESET/TUNING
HOUR
TREBLE
MIN
MIN
MAX
INPUT
BALANCE
PHONES
–
+
TIME ADJ
1
2
3
4
–
+
L
R
PRESET/BAND
Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
While the power is on, press DISPLAY to display
the time.
Press HOUR while holding TIME ADJ to advance
the hour setting.
• Press HOUR while holding TIME ADJ and
PRESET/BAND to reverse the hour setting.
Press MIN while holding TIME ADJ to advance the
minute setting.
• Press MIN while holding TIME ADJ and
PRESET/BAND to reverse the minute setting.
To display the clock
Press DISPLAY.
The current time appears for about 8 seconds, then the
normal display returns. Some buttons and controls may
not work while the current time is displayed.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
6
NAMES OF BUTTONS AND CONTROLS
1 2
3 45 6 7 8
English
Front panel
9
VOLUME
NATURAL SOUND
STEREO RECEIVER
RX–E600
STANDBY/ON
DISPLAY
TIMER
MEMORY
AUTO/MAN'L
TIMER ADJ
TIMER
PRESET/TUNING
PRESET/BAND
HOUR
BASS
TREBLE
MIN
MIN
MAX
INPUT
BALANCE
PHONES
–
0 q
+
w
–
+
e
1 STANDBY/ON (P.9)
2 TIMER indicator (P.15)
3 DISPLAY (P.15)
4 MEMORY/TIME ADJ (P.6/P.11)
5 AUTO/MAN’L/TIMER (P.10/P.15)
6 PRESET/BAND (P.10)
7 Display (P.7)
8 PRESET/TUNING / (P.10)
HOUR/MIN (P.6/P.15)
R
L
r
t
9 VOLUME (P.9)
0 PHONES (P.9)
q Remote control sensor (P.3)
w BASS (P.9)
e TREBLE (P.9)
r BALANCE (P.9)
t INPUT (P.9)
Display
PRESET
EDIT
1
STEREO AUTO RDS PS PTY RT CT
TUNED MEMORY
PTY HOLD
23 456 7 89
1 Multi-information display
2 EDIT indicator
3 PRESET indicator (P.11)
4 STEREO indicator (P.10)
5 TUNED indicator (P.10)
6 AUTO indicator (P.10)
0
TIMER
SLEEP
q
w
7 MEMORY indicator (P.11)
8 RDS indicator (P.12)
9 RDS mode indicators (P.12)
0 PTY HOLD indicator (P.13)
q TIMER indicator (P.15)
w SLEEP indicator (P.16)
7
NAMES OF BUTTONS AND CONTROLS
Remote control
POWER
1
2
3
6
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
B
4
5
C
TIME
D
E
TAPE
DIRECTION
PRESET
7
9
MD
TUNER
PRESET
DVD
TAPE
AUX
MD
REC/PAUSE
MODE
e
TAPE
REC/PAUSE
DUBBING
SLEEP
8
0
q
w
START
DISPLAY
VOLUME
8
r
t
1 POWER (P.9)
2 Preset numbers (P.11)
3 FREQ/RDS (P.12)
4 PTY SEEK MODE (P.13/P.14)
5 PTY SEEK START (P.13/P.14)
6 A/B/C/D/E (P.11)
7 PRESET / (P.11)
8 TUNER (RX-E600) (P.11)
9 MD input (MDX-E300) (P.18)
0 TAPE input (KX-E300) (P.18)
q DVD input (DVD-E600) (P.17)
w AUX (The equipment connected to the AUX
terminal) (P.5)
e SLEEP (P.16)
r DISPLAY (P.15)
t VOLUME %/fi (P.9)
Note
• 8~w are operation buttons and input selectors for each
component.
BASIC OPERATIONS
STANDBY/ON
TREBLE
1
2
VOLUME
STEREO RECEIVER
RX–E600
STANDBY/ON
TIMER
DISPLAY
MEMORY
AUTO/MAN'L
TIMER ADJ
TIMER
BASS
PRESET/TUNING
PRESET/BAND
HOUR
TREBLE
MIN
MIN
MAX
INPUT
BALANCE
PHONES
–
+
–
+
L
R
3
PHONES
BASS
BALANCE
INPUT
POWER
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
5
6
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
B
E
PRESET
TUNER
TAPE
AUX
MODE
If desired, adjust BASS, TREBLE, and BALANCE.
BALANCE: Adjust the balance of the output volume
from the left and right speakers to compensate for
sound imbalance caused by the speaker location or
listening room conditions.
PRESET
DVD
MD
REC/PAUSE
Adjust the volume level by turning VOLUME on the
front panel or pressing VOLUME %/fi on the remote
control.
TREBLE: Turn this control clockwise to increase (or
counterclockwise to decrease) the high frequency
response.
TAPE
DIRECTION
MD
Start playback on the source component. (Refer to the
owner’s manual supplied with each selected component.)
BASS: Turn this control clockwise to increase (or
counterclockwise to decrease) the low frequency
response.
C
TIME
D
Select the desired input source by turning INPUT until a
suitable source component name appears on the display.
• When you operate the component connected to the
AUX terminal, turn INPUT to select AUX.
4
POWER
Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
• Piano Craft series components that have correct
system connections made to RX-E600 can be
controlled to turn to the on or standby mode by
RX-E600. However, once the connected
components are turned to the standby mode with
their respective STANDBY/ON button, they
cannot be controlled by RX-E600 STANDBY/
ON button.
VOLUME
NATURAL SOUND
Set the volume to “MIN” by turning VOLUME.
English
Listening to a source
TAPE
REC/PAUSE
DUBBING
SLEEP
When you use headphones
START
DISPLAY
VOLUME %/fi
VOLUME
Connect the headphones to the PHONES jack. You can
listen to the sound to be output from the main speakers
through the headphones.
When you have finished using this unit
Press STANDBY/ON on the front panel again or
POWER on the remote control to set this unit to the
standby mode.
Auto standby function
This unit will automatically place itself in standby mode
under the following conditions:
• When you select a component connected to this unit
with a system control cable as an input source.
• The source component is stopped and has not been
operated for 30 minutes.
9
TUNING
Listening to the radio
You can find radio stations automatically and manually.
AUTO/MAN’L PRESET/TUNING
/
VOLUME
NATURAL SOUND
STEREO RECEIVER
DISPLAY
MEMORY
AUTO/MAN'L
TIMER ADJ
TIMER
BASS
PRESET/BAND
PRESET/TUNING
HOUR
TREBLE
MIN
MIN
MAX
INPUT
BALANCE
PHONES
–
+
–
+
L
R
PRESET/BAND
INPUT
Automatic tuning
1
2
3
4
5
Select TUNER by turning INPUT so that the
frequency of a radio station appears in the display.
Press PRESET/BAND to select the reception band.
Do not select the preset tuning mode (in which
“PRESET” appears on the display).
Press AUTO/MAN’L so that “AUTO” appears in the
display.
Press PRESET/TUNING
(For a higher
(For a lower frequency).
frequency) or
The unit starts searching for a station.
STEREO
AUTO
TUNED
When the unit finds a station, it stops searching and
“TUNED” appears on the display.
6
If the station located is not the one you want, repeat
steps 4 and 5 until you find a suitable station.
Notes
• If automatic tuning search does not find the desired station, try
manual tuning as described next.
• When an FM stereo broadcast with sufficient signal strength is
received, “STEREO” appears on the display and you can listen
to stereo sound.
10
1
2
3
RX–E600
STANDBY/ON
TIMER
Manual tuning
Follow steps 1 and 2 described in “Automatic
tuning.”
Press AUTO/MAN’L so that “AUTO” disappears
from the display.
Press PRESET/TUNING
(for a higher
(for a lower frequency) to select
frequency) or
your desired station.
• The frequency changes incrementally each time
you press PRESET/TUNING.
TUNING
The unit can store station frequences selected using
Automatic or Manual tuning as presets. Up to 40 stations
can be stored. With this function, you can select any
desired station by pressing the corresponding preset
station number.
PRESET/TUNING
/
STEREO RECEIVER
Select TUNER as input source by turning INPUT.
Press MEMORY for about 2 seconds.
• The unit starts presetting stations, “AUTO” and
“MEMORY” will flash on the display.
Received stations are stored to A1, A2...A8 sequentially.
After 40 stations or all FM and AM stations are stored, the
display will show the preset station A1.
To recall a preset station
VOLUME
NATURAL SOUND
1
2
RX–E600
STANDBY/ON
DISPLAY
TIMER
MEMORY
AUTO/MAN'L
TIMER ADJ
TIMER
BASS
PRESET/BAND
PRESET/TUNING
HOUR
TREBLE
MIN
MIN
MAX
INPUT
BALANCE
PHONES
–
+
–
+
L
Press TUNER and select the desired number by pressing
PRESET/BAND and PRESET/TUNING / on the
front panel or PRESET / , A/B/C/D/E and 1–8 on
the remote control.
R
POWER
MEMORY PRESET/BAND
INPUT
1–8
To preset stations manually
1
2
3
Tune in a desired station.
(Refer to the previous page for the tuning procedure.)
Within about 5 seconds, use PRESET/TUNING
/ to select a desired preset number. Continue
pressing PRESET/TUNING / to select the
group of the preset stations (A, B, C, D, and E).
2
3
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A/B/C/D/E
Press MEMORY.
1
1
4
A
B
C
TIME
D
E
TAPE
DIRECTION
PRESET
MD
TUNER
PRESET
TAPE
DVD
TUNER
PRESET
/
AUX
PRESET
STEREO
TUNED
MEMORY
MD
REC/PAUSE
MODE
4
Press MEMORY.
• “MEMORY”, “PRESET”, and preset number will
appear on the display.
TAPE
REC/PAUSE
DUBBING
SLEEP
START
DISPLAY
VOLUME
The arrow will appear for a second when
it is preset.
PRESET
STEREO
TUNED
5
MEMORY
Repeat steps 1 to 4 until all desired stations are
preset.
Notes
• A new setting can be preset in place of a previous one.
• The preset stations are retained for a week after you disconnect
the AC power cord or a power failure occurs.
11
English
English
To preset stations automatically
Presetting stations
RECEIVING RDS STATIONS
Receiving RDS data
RDS (Radio Data System) is a data transmission system
used by FM stations in many countries. Stations using this
system transmit an inaudible stream of data in addition to
the normal radio signal. RDS data contains various types
of information, such as PS (Program Service), PTY
(Program Type), RT (Radio Text), and CT (Clock Time).
POWER
FREQ/RDS
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
PS
The name of the RDS station being received is displayed.
• If the unit cannot find a station with PS data, the unit stops
searching and “NO PS” appears on the display.
RDS PS
PTY
The type of the program on the RDS station now being
received is displayed. You can make this unit search for a
station which is broadcasting a program of a desired
program type. (Refer to PTY program mode in the next
section for details.)
RDS
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
B
PTY
C
TIME
D
E
TAPE
DIRECTION
PRESET
TUNER
MD
TUNER
PRESET
TAPE
DVD
AUX
MD
REC/PAUSE
MODE
TAPE
REC/PAUSE
DUBBING
RT
Information about the program (such as the title of the
song, name of the singer, etc.) on the RDS station being
received is displayed by a maximum of 64 alphanumeric
characters, including the umlaut symbol. If other
characters are used in the RT data, they are displayed with
an under-bar.
• If the unit cannot find a station with RT data, the unit stops
searching and “NO RT” appears on the display.
START
RDS
SLEEP
RT
DISPLAY
VOLUME
CT
Current time is displayed.
• If the unit cannot find a station with CT data, the unit stops
searching and “NO CT” appears on the display.
1
2
12
Tune in the FM station. (Refer to page 10, or you can
simply press TUNER on the remote control.)
Press FREQ/RDS to choose the mode. Each time
you press FREQ/RDS, the type changes as follows:
RDS
CT
Notes
• RDS may not work properly if the station you are tuned to is
not transmitting the RDS signal properly or if the signal
strength is weak.
• Some FM stations do not offer RDS service. Of those that do,
not all provide the same types of services. The types provided
by the received RDS station are dimmed on the display. Check
with your local radio stations for details on RDS services in
your area.
RECEIVING RDS STATIONS
You can locate a desired station by selecting a program
type. The unit searches all preset stations into the type of
programs currently being broadcast from the RDS
stations.
1
2
Tune in the FM station. (Refer to page 10, or you can
simply press TUNER on the remote control.)
English
To locate a station
PTY SEEK mode
Press PTY SEEK MODE once so that “PTY” and a
PTY program flashes on the display.
POWER
PTY SEEK MODE
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
B
PTY
3
PTY SEEK START
4
C
TIME
D
E
Within about 20 seconds, press PRESET /
repeatedly until the desired programGetting
type Playing
appearsStarted
on CDs
the display.
Within about 20 seconds, press PTY SEEK START.
• If a station broadcasting the selected program type
is found, the unit stops searching and the Program
Service name appears on the display.
“PTY HOLD” appears on the display.
TAPE
DIRECTION
PRESET
TUNER
PRESET
PRESET
MD
TAPE
DVD
PRESET
AUX
MD
REC/PAUSE
MODE
TAPE
REC/PAUSE
DUBBING
SLEEP
START
DISPLAY
/
RDS
PTY
PTY HOLD
5
Repeat step 4 until the desired station is located.
If there is no station broadcasting the program type
you select, “NO PTY” appears on the display, then
the Program Service name or frequency appears on
the display.
VOLUME
List of PTY (Program Type)
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M.O.R. M
News
Current Affairs
General Information
Sports
Education
Drama
Culture
Science
Light Entertainment
Pops
Rock
Middle of the Road
Music (Easy-listening)
LIGHT M
Light Classics
CLASSICS Serious Classics
OTHER M Other Music
13
RECEIVING RDS STATIONS
• If the unit is tuned to an RDS station of another
country the built in clock synchronizes to the time
of that country.
• If the built-in clock is not set to the current time or
has been reset due to a power failure or other
incident, it will be set to the time specified by the
CT automatically, regardless of whether this
setting is set ON or OFF.
Optional settings for
RDS functions
The tuner has the following functions which make use of
the RDS data service. These functions are set to ON by
default. However, you can turn these functions OFF, if so
desired.
2. LOCAL = CT (ON/OFF)
If the RDS station being received employs the
local time (summer time, etc.) data service, its
time is displayed in the CT mode.
POWER
PTY SEEK MODE
FREQ/RDS
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
B
PTY SEEK START
3. A.M. = RDS (ON/OFF)
The unit searches RDS stations instead of FM
stations in the automatic preset tuning operation
when this setting is set to ON. (Refer to page 11).
C
TIME
D
E
TAPE
DIRECTION
PRESET
TUNER
MD
TUNER
PRESET
TAPE
DVD
4. RT SPEED: ±0
Changes the scroll speed of the radio text.
Decrease the value to reduce the speed.
AUX
MD
REC/PAUSE
MODE
TAPE
REC/PAUSE
DUBBING
SLEEP
START
DISPLAY
DISPLAY
VOLUME
Control Range: ±0 to ±3 (Preset value: ±0)
5
1
2
3
4
Select the FM band by pressing TUNER.
Press DISPLAY to display the current time.
Press FREQ/RDS.
Each time you press PTY SEEK MODE the display
will change as follows:
1. CT = CLOCK (ON/OFF)
The tuner corrects the time of the built-in clock
automatically by synchronizing it with the CT
data on the RDS station being received.
14
6
Choose the function ON or OFF by pressing PTY
SEEK START, confirming it in the display. Press
PTY SEEK START repeatedly to change the value
for RT SPEED.
• If the unit is not operated for 20 seconds or more,
this mode is cancelled and the unit returns to the
frequency display. If the current station is
transmitting PS data, the unit changes to the PS
mode.
Press FREQ/RDS again to restore the frequency
display mode.
USING THE BUILT-IN TIMER
USING THE BUILT-IN TIMER
If you want to use the cassette deck, KX-E300 or the MD
Recorder, MDX-E300 for timer play or recording, you
must first make the connections as shown in “Connecting
the system” on page 5. For details, refer to the instructions
supplied with the MDX-E300 or KX-E300.
(Example)
Timer play and recording
By using the built-in timer, you can have the unit turn on
at a specified time and begin playing or recording
automatically. You can also specify the time at which you
want the unit to turn off.
DISPLAY
4. ON Time
“ON Time” appears on the display for a second,
and changed to the time setting mode.
Press HOUR to set the hour.
Press MIN to set the minute.
HOUR MIN
VOLUME
NATURAL SOUND
STEREO RECEIVER
RX–E600
5. OFF Time
Set the time the same way as above.
If you set the ON time but not OFF time, timer
play or recording will finish automatically after an
hour.
STANDBY/ON
TIMER
DISPLAY
MEMORY
AUTO/MAN'L
TIMER ADJ
TIMER
BASS
PRESET/BAND
PRESET/TUNING
HOUR
TREBLE
MIN
MIN
MAX
INPUT
BALANCE
PHONES
–
+
–
TIMER
1
+
L
Notes
R
• The display mode changes after approximately 8 seconds.
If you change the mode before completing setting, press
DISPLAY once or more to return to the desired mode.
• If you select the input other than TUNER and AUX on
“2. Timer Input”, “3. Timer REC” is skipped.
INPUT
Press DISPLAY.
Whenever DISPLAY is pressed, the display mode
changes as follows:
1. Clock Time (TIMER on/off mode)
If you have not set the clock yet “Set Clock”
appears. You need to set the current time as
described on page 6.
2. Timer Input
Select the source to be played by turning INPUT.
• Timer recording is possible only when you
select TUNER or AUX.
2
Press TIMER to complete the timer setting.
The system changes to the standby mode.
• TIMER indicator lights up.
If you continue using the system, press STANDBY/
ON to turn on this unit.
To cancel the timer play setting
Press DISPLAY to show the current time, then press
TIMER so that “TIMER” disappears from the display.
You can also cancel the timer play setting by pressing
TIMER when the unit is in standby mode.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
15
English
3. Timer REC
Select the recording component by turning
INPUT. If you wish to enjoy timer playback with
the TUNER or AUX settings, select “REC Mode
OFF”.
Before using the timer
USING THE BUILT-IN TIMER
Sleep timer
The unit can be set to automatically place itself in standby
mode after a designated time.
PRESET
MD
TUNER
PRESET
TAPE
DVD
AUX
MD
REC/PAUSE
MODE
SLEEP
TAPE
REC/PAUSE
DUBBING
START
SLEEP
DISPLAY
VOLUME
1
2
Play the desired sound source.
Press SLEEP repeatedly until the desired sleep time
appears in the display. Each time you press SLEEP,
the sleep time changes as follows:
SLEEP 2h00m
SLEEP 1h30m
SLEEP 1h00m
SLEEP 0h30m
SLEEP OFF
About 4 seconds after setting, the normal display will
resume.
• “SLEEP” will appear in the display.
3
16
The unit will turn off automatically when the selected
sleep time is reached.
SYSTEM CONTROL
DVD-E600
POWER
1
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
1 Numeric buttons
• +100 button is used when operating
MDX-E300.
2 * (Pause)
3 # (Play)
4 & (Stop)
5 $ ! (Skip/Seach Backward)
6 ⁄ › (Skip/Seach Forward)
7 DVD input
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
2
3
4
5
B
C
TIME
D
E
6
TAPE
DIRECTION
PRESET
MD
TUNER
PRESET
DVD
TAPE
7
AUX
MD
REC/PAUSE
MODE
English
Controlling other components
TAPE
REC/PAUSE
DUBBING
SLEEP
START
DISPLAY
VOLUME
17
SYSTEM CONTROL
MDX-E300
POWER
1
2
3
4
1
2
3
1
4
2
5
3
6
4
7
5
8
6
9
7
0
8
+10
+100
FREQ/RDS MODE–PTY SEEK–START
REP
RANDOM
PROG
A
B
D
E
6,1
8,3
9,4
7,2
TAPE
DIRECTION
PRESET
0
5
C
TIME
MD
KX-E300
TUNER
PRESET
DVD
TAPE
5
AUX
q
MD
REC/PAUSE
MODE
TAPE
REC/PAUSE
DUBBING
SLEEP
START
DISPLAY
VOLUME
18
1 Numeric buttons
2 REP (Repeat)
3 RANDOM
4 * (Pause)
5 PROG (Program)
6 # (Play)
7 ⁄ › (Skip/Search Forward)
8 $ ! (Skip/Search Backward)
9 & (Stop)
0 MD input
q MD REC/PAUSE
6
1 # (Play)
2 ⁄ › (Fast-foward)
3 $ ! (Rewind)
4 & (Stop)
5 TAPE input
6 TAPE REC/PAUSE
SYSTEM CONTROL
3
Play unit
Record unit
English
Before recording
Follow the instructions as described in “Connecting the
system” on page 5 before using the MDX-E300 or KXE300 to record. For details, refer to the instructions
supplied with the MDX-E300 or KX-E300. Sources
connected to the AUX terminal can be recorded to tape or
MD.
• Recording automatically starts at the beginning of
the tape. (Pressing DUBBING START
automactially rewinds the tape to the beginning)
Dubbing setting
4
There are six combinations of components. When you
select a mode, recording for mode starts and ends
automatically in a manner preset for that mode.
TAPE
DIRECTION
PRESET
MD
TUNER
TAPE
2
AUX
MD
REC/PAUSE
Record unit
• Recording automatically starts at the beginning of
the tape. (Pressing DUBBING START
automactially rewinds the tape to the beginning)
PRESET
DVD
Play unit
Press DUBBING START to start recording.
TAPE
REC/PAUSE
Note
MODE
DUBBING
MODE
DUBBING
SLEEP
START
DISPLAY
DUBBING
START
VOLUME
• The displays 1~4 which include the component you have
not connected to your receiver (RX-E600) will be skipped.
To stop dubbing
Press &.
1
Select a component combination. Each time you
press DUBBING MODE, the mode changes in the
following order:
Note
• If DVD playback stops or completes when you are using the
DVD player as a recording source, the recording component
records 10 additional seconds of silence.
1
2
19
ADDITIONAL INFORMATION
Troubleshooting
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the
simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the
power cord and contact your authorized YAMAHA dealer or service center for help. When receiving service, other Piano
Craft components you are using together with this unit may be needed.
SYMPTOM
CAUSE
REMEDY
The unit does not switch ON when the
STANDBY/ON switch is pressed.
The AC power cord is not connected or not
completely connected.
Securely connect the power cord.
No sound from one speaker.
Loose speaker connections.
Connect properly.
The sound suddenly goes off.
The protection circuit has been activated
because of a short circuit, etc.
Check the speaker wires are not touching each other
and then turn the unit back on.
No sound from an external unit
connected with this unit or play does not
begin.
Incorrect cord connections.
Connect the cords properly. If the problem persists,
the cords may be defective.
Input source selection is not proper.
Make a proper input source selection.
Sound distorted.
The component connected to this unit is
disconnected from AC outlet.
Connect the AC power cord of the component to an
AC outlet.
Excessive static in FM broadcasts.
Interference from starting motor of a nearby
car.
Position the FM antenna as high and as far away
from nearby roads as possible. Connect using a
coaxial cable.
Interference from the thermostat of a nearby
electrical appliance.
Noise increases during stereo
broadcasts.
Antenna input is too weak due to obstructions
or excessive distance from the broadcasting
station.
Check the antenna connection.
Stereo broadcasts are noisy and
STEREO indicator blinks on and off.
Insufficient antenna input.
Install an antenna appropriate for the electric field
strength of your area.
Cannot select preset stations.
Preset memory has been erased.
Reprogram memory presets.
Buzzing or static during AM broadcasts.
Interference from sources such as lightning,
fluorescent lights, electric motors or thermostat
of nearby electrical appliance.
The problem is difficult to eliminate, but can be
lessened by grounding AM loop antenna.
TV or microprocessor is being used nearby.
Move away from TV or microprocessor.
Radio signal is weak or the antenna is not
properly connected.
Properly connect the AM loop antenna.
AM broadcast sensitivity is poor.
Install a multi-element type FM antenna if possible.
Change orientation of the AM loop antenna.
Install an external AM loop antenna.
Cannot set timer.
Current time is not set.
Set current time.
The unit does not work normally.
The internal microcomputer has been frozen
by an external electric shock (lightning,
excessive static electricity, etc.) or the power
supply with low voltage.
Unplug the AC power cord from the wall outlet, and
then plug in again after about one minute.
20
ADDITIONAL INFORMATION
The remote control does not work.
TV functions strangely when the remote
control is being used.
CAUSE
REMEDY
The batteries of the remote control are too
weak.
Replace the batteries with new ones.
Remote control is too far away or is being
used at an incorrect angle.
Use within 6 meters and 60 degree radius.
Direct sunlight or lighting (of an inverter type
of fluorescent lamp, etc.) is striking the
remote control sensor of the unit.
Change the position of the unit.
Remote control is being used near TV set
with a remote control sensor.
Relocate this unit away from the TV or cover the
TV’s remote control sensor.
English
SYMPTOM
21
ADDITIONAL INFORMATION
Specifications
Amplifier section
General
Minimum RMS output power per channel
................................................ 55 W + 55 W (6Ω 1kHz 0.1% THD)
.............................. 40 W + 40 W (6Ω 20 Hz to 20 kHz 0.1% THD)
DIN Standard output power per channel (Europe model)
................................................ 60 W + 60 W (4Ω 1kHz 0.7% THD)
Input sensitivity/Impedance
DVD/TAPE/MD/AUX .............................................. 150 mV/47 kΩ
Frequency response
DVD etc. .................................................. 20 Hz to 20 kHz, ±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
DVD etc. 20 W, 6 Ω ................................................................ 0.04%
Signal-to-Noise ratio (IHF-A Network)
DVD etc. (250 mV, Input shorted) .......................................... 98 dB
Output level/Impedance
PHONES ..................................................................... 0.43 V/330 Ω
Power supply
[U.S.A. and Canada models] ................................. AC 120 V, 60 Hz
[Australia model] ................................................... AC 240 V, 50 Hz
[U.K. and Europe models] ..................................... AC 230 V, 50 Hz
[Asia and General models]
............................................. AC 110/120/220/230-240 V, 50/60 Hz
[Korea model] ........................................................ AC 220 V, 60 Hz
Power consumption
[U.S.A. and Canada models] .................................................. 110 W
[Other models] ........................................................................ 125 W
Power consumption (standby mode)
[U.S.A. and Canada models] ................................................... 0.7 W
[Other models] ......................................................................... 0.8 W
Dimensions (W x H x D)
................................. 217 x 108 x 372 (8-5/8” x 4-1/4” x 14-8/5”) mm
Weight ..................................................................... 5.4 (11.9 lbs) kg
Tuner section
Specifications are subject to change without notice.
Tuning range
FM
[U.S.A. and Canada models] ................................ 87.5 – 107.9 MHz
[U.K., Europe, Australia and Korea models]
.......................................................................... 87.50 – 108.00 MHz
[Asia and General models] ............ 87.5/87.50 – 108.0/108.00 MHz
AM
[U.S.A. and Canada models] ................................... 530 – 1710 kHz
[U.K., Europe, Australia and Korea models] .......... 531 – 1611 kHz
[Asia and General models] ...................... 530/531 – 1710/1611 kHz
Sensitivity
FM (S/N 30dB) ....................................................................... 1.0 µV
AM .................................................................................... 300 µV/m
0112RXE600_EB_20-23_E.p65
20
2004.09.02, 16:52
0100DVD-E600_EB_cover.fm Page 1 Monday, August 23, 2004 4:58 PM
EB
DVD-E600
©2004
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
Printed in Malaysia
WD90090
DVD-E600
DVD PLAYER
LECTEUR DE DVD
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
Important Note
DK
Advarsel:
Laserrudstråling ved åbning når sikkerhesafbrydere er ude
af funktion. Undgå u tsættelse for stråling.
Bemærk:
Netafbryderen STANDBY/ON er sekundært indkoblet og
afbryder ikke strømmen fra nette. Den indbyggede netdel er
derfor tilsluttet til lysnettet så længe netstikket sidder i
stikkontakten.
N
Observer:
Nettbryteren STANDBY/ON er sekundert innkoplet. Den
innebygdenetdelen er derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
S
Klass 1 laserapparat
Varning!
Om apparaten används på annat sätt än i denna
bruksanvisning specificerats, kann användaren utsättas för
laserstrålning, som översjruder gränsen för läserklass 1.
SF
Luokan 1 laserlaite + Klass 1 laserapparat
Varoitus!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan
1 ylittävälle lasersäleilille.
Huom.
Toiminnanvalitsin STANDBY/ON on kytketty toisiopuolelle,
eikä se kytke laitetta irti sähköverkosta. Sisäänrakennettu
verkko-osa on kytkettynä sähköverkkoon aina silloin, kun
pistoke on pistorasiassa.
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
Observera!
Strömbrytaren STANDBY/ON är sekundärt kopplad och inte
bryter strömmen fråan nätet Den inbyggda nätdelen är
därför ansluten till elnätet så länge stickproppen sitter i v
ägguttaget.
Important Note for Users in the UK
If the fitted plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of
5 Amp. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5 Amp.
How to connect a plug
The wires in the mains lead are coloured with the following
code: blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour
markings identifying the terminals in your plug, proceed as
follows:
● Connect the blue wire to the terminal marked N or
coloured black.
● Connect the brown wire to the terminal marked L or
coloured red.
● Do not connect either wire to the earth terminal in the
plug, marked E (or e) or coloured green (or green and
yellow).
Note:The severed plug must be disposed of to avoid a
possible shock hazard should it be inserted into a 13
Amp socket elsewhere.
Before replacing the plug cover, make certain that the cord
grip is clamped over the sheath of the lead - not simply over
the two wires.
Mains plug
This apparatus is fitted with an approved 13 Amp plug.To
change a fuse in this type of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp, A.S.T.A.
or BSI approved type.
3 Refit the fuse cover.
Copyright in the U.K.
Recording and playback of material may require consent.
See Copyright Act 1956 and The Performer’s Protection
Acts 1958 to 1972.
i
General information
CAUTION
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette brochure
peut entraîner une exposition à d’éventuelles radiations
pouvant être dangereses.
ACHTUNG
Die Verwendung von Bedienungselementen oder
Einstellungen oder die Durchführung von
Bedienungsvorgängen, die nicht in dieser Anleitung
aufgeführt sind, kann zu einem Kontakt mit gefährlichen
Laserstrahlen führen.
OBSERVERA
Användning av kontroller och justeringar eller
genomförande av procedurer andra än de som
specificeras i denna bok kan resultera i att du utsätter dig
för farlig strålning.
ATTENZIONE
Uso di controlli o regolazioni o procedure non
specificamente descritte può causare l’esposizione a
radiazioni di livello pericoloso.
PRECAUCIÓN
El uso de los controles o los procedimientos de ajuste o
utilización diferentes de los especificados en este manual
pueden causar una exposición peligrosa a la radiación.
VOORZICHTIG
Gebruik van bedieningsorganen of instellingen, of
uitvoeren van handelingen anders dan staan beschreven
in deze handleiding kunnen leiden tot blootstelling aan
gevaarlijke stralen.
SYSTEM
CONNECTOR
The unit is not disconnected from the AC power source as
long as it is connected to the wall outlet,even if this unit
itself is turned off.This state is called the standby mode.In
this state,this unit is designed to consume a very small
quantity of power.
English
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
L ’appareil n ’est pas isolé de la source d ’alimentation
aussi longtemps qu ’il reste branché sur une prise
murale,même lorsqu ’il est éteint.Il est alors dit en mode
«Veille ».Dans ce mode, l ’appareil consomme très peu de
courant.
Das Gerät ist nicht vom Netz getrennt, solange der
Netzstecker noch mit der Wandsteckdose verbunden ist,
selbst wenn das Gerät ausgeschaltet wurde. Dieser
Betriebszustand wird als Bereitschaftsmodus bezeichnet.
In diesem Zustand nimmt das Gerät eine sehr geringe
Menge Strom auf.
Enheten är inte urkopplad från nätet så länge som den är
ansluten till vägguttaget även om enheten i sig självt är
avstängd. Detta kallas för beredskapsläge och i detta
tillstånd konsumerar apparaten minimalt med ström.
L’unità non è scollegata dall’impianto elettrico di casa
sintanto che rimane collegata ad una presa di corrente
anche se è spenta. Questo modo viene chiamato “modo di
attesa”. In esso, l’unità consuma una quantità molto bassa
di energia per mantenere in memoria le impostazioni da voi
fatte.
Aunque el propio aparato se encuentre apagado, éste no
se desconectará de la fuente de CA siempre que se
mantenga enchufado a la toma de corriente. Este estado
recibe el nombre de “modo de espera”. En este estado,
este aparato ha sido diseñado para consumir una cantidad
muy pequeña de energía.
De stroomtoevoer naar het toestel is niet afgesloten zolang
de stekker nog in het stopcontact zit, zelfs niet als het
toestel zelf uitgeschakeld is. Deze toestand wordt
“standby” (waak- of paraatstand) genoemd. Het toestel is
ontworpen om in deze toestand.
RECEIVER
COMPONENT VIDEO OUT
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
PR
PB
AV
Y
DIGITAL
OUT
AUDIO
OUT
VIDEO OUT
L
VIDEO
R
S VIDEO
COAXIAL
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
OPTICAL
E
CAUTION VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO BEAM.
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED
ÅBNING. UNDGÅ UDSÆTTELSE FOR STRÅLING.
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR
DEKSEL ÅPNES. UNNGÅ EKSPONERING FOR STRÅLEN.
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO
SÄTEESEEN.
VORSICHT SICHTBARE UND UNSICHTBARE
LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET.
NICHT DEM STRAHL AUSSETSEN.
DANGER VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.
ATTENTION RAYONNEMENT LASER VISIBLE ET
INVISIBLE EN CAS D’OUVERTURE. EXPOSITION
DANGEREUSE AU FAISCEAU.
ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
iii
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this sound system in a well ventilated, cool, dry,
clean place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet, allow
about 2.5cm (1 inch) of free space all around this unit for
adequate ventilation.
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause
an electrical shock, fire, damage to this unit, and/or
personal injury.
Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of this
unit, do not place:
– Other components, as they may cause damage and/
or discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall, spilling
the liquid and causing an electrical shock to the user
and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all connections
are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use excessive force on switches, knobs and/or
cords.
When disconnecting the power cord from the wall outlet,
grasp the plug; do not pull the cord.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Use only the voltage specified on this unit. Using this unit
with a higher voltage than specified is dangerous and
may cause fire, damage to this unit, and/or personal
injury. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage other
than as specified.
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reason.
When not planning to use this unit for long periods of time
(i.e., vacation), disconnect the AC power plug from the
wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
Before moving this unit, press STANDBY/ON to set the
unit in standby mode, then disconnect the AC power plug
from the wall outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
NOTE:
Pictures shown maybe different between countries.
Never make or change connections with the power switched
on.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt
to service this device.
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM (WARNING LOCATION:
INSIDE ON LASER COVERSHIELD OR THE BACKPLATE OF
SET)
LASER
Type
Wave length
Semiconductor laser GaAlAs
650 nm (DVD)
780 nm (VCD/CD)
Output Power
7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degree
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam.
When this unit is plugged into a wall outlet, do not place your
eyes close to the opening of the disc tray and other openings
or look inside.
Contents
Picture CD & MP3 Playback
Environmental Information ............................ 2
Supplied accessories .................................... 2
Notes about discs.......................................... 2
General Operation....................................... 12
Cleaning discs .................................................... 2
Special JPEG Features............................... 13
Symbols Used in this Manual........................ 2
Function Introduction ........................................ 13
Preview Function............................................... 13
Zoom picture..................................................... 13
Playback with multi-angles ............................... 13
Wipe Effect........................................................ 13
Functional Overview
MP3 & JPEG Navigator ..................................... 12
Play Mode ......................................................... 12
Front and Rear Panels .................................. 3
Remote Control ............................................. 4
Special MP3 Features................................. 13
Preparation
JPEG and MP3 simultaneous playback ...... 13
General Notes on connections...................... 5
Digital Connections ....................................... 5
Analog Connections ...................................... 5
Video Connections ........................................ 6
Function Introduction ........................................ 13
Setup Menu
Basic Operation........................................... 14
General Setup menu ................................... 14
S-Video terminal <A>.......................................... 6
Composite Video terminal <B>........................... 6
Component Video terminal <C> ......................... 6
SCART Connection <D> ..................................... 6
DISC LOCK ....................................................... 14
PROGRAM (not for Picture CD/MP3) ................ 14
OSD LANGUAGE.............................................. 15
SCREEN SAVER................................................ 15
Inserting batteries into the Remote Control... 7
Audio Setup menu....................................... 15
Using the Remote Control ................................... 7
SPEAKER SETUP .............................................. 15
DIGITAL AUDIO SETUP.................................... 16
EQUALIZER (Sound Mode) .............................. 16
3D (REVERB MODE)......................................... 16
PAL/NTSC Conversion ................................. 7
Turning on the power .................................... 7
Smart Power On/Off...................................... 7
Video Setup menu....................................... 17
Operation
Basic Playback.............................................. 8
General Operation......................................... 8
Video control during playback ............................ 8
Audio control during playback............................ 8
Repeat and Shuffle.............................................. 9
Repeat A-B.......................................................... 9
Disc Resume ....................................................... 9
OSD (On-Screen Display) ................................... 9
Zoom ................................................................. 10
Special DVD Features................................. 10
Playing a Title .................................................... 10
Playing a Chapter.............................................. 10
Camera Angle ................................................... 10
Changing the Audio Language and/or format .. 10
Subtitles............................................................. 10
TV TYPE ............................................................ 17
TV DISPLAY ...................................................... 17
CLOSED CAPTION ........................................... 18
COMPONENT ................................................... 18
PROGRESSIVE.................................................. 18
PICTURE SETTING ........................................... 19
PASSWORD SETUP .................................. 19
Preference Setup menu .............................. 20
AUDIO language............................................... 20
SUBTITLE language.......................................... 20
DISC MENU language ...................................... 20
PARENTAL Control ........................................... 21
DEFAULT Setup ................................................ 21
MP3/JPEG NAV................................................. 21
Troubleshooting............................ 22
Special VCD & SVCD Features .................. 10
Playback Control (PBC) .................................... 10
Preview Function ............................................... 11
Specifications................................ 23
Maintenance .................................. 23
Language Code ............................. 24
1
English
Introduction
Introduction
Thank you for purchasing this unit. This Owner’s Manual
explains the basic operation of this unit.
The region code for this set is 2.
2
Since it is usual for DVD movies to be
released at different times in different regions
of the world, all players have region codes and discs can
have an optional region code. This unit can play discs
containing the identical region code, or mentioned as
region “ALL”. If you load a disc of a different region code
to this unit, you will see the region code notice on the
screen. The disc will not play, and should be unloaded.
Environmental Information
This unit consists of materials which can be recycled and
reused if disassembled by a specialised company.
Please observe the local regulations regarding the
disposal of packaging materials, exhausted batteries
and old equipment.
Supplied accessories
–
–
–
–
–
–
Remote control
Batteries (two AA size) for remote control
Audio pin cable
Video pin cable
System control cable (green)
Owner’s Manual
Cleaning discs
● When a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the centre out. Do not wipe in a
circular motion.
● Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analog records.
Symbols Used in this Manual
The below symbols appear in some headings and notes
with the following meanings:
DVD
– Description refers to playback of
DVD-video discs
VCD
– Description refers to playback of
Video CDs
CD
– Description refers to playback of
Audio CDs
SVCD
– Description refers to playback of
Super VCDs
● Some DVD video discs require specific functions or allow
only limited functions during playback.
● “ ✕ ” may appears on the TV screen which means that the
function is not available on that specific DVD video disc.
Notes about discs
– This unit is designed for use with DVD video, Video CD,
Super video CD, Audio CD, CD-R, CD-RW (MP3 Supported),
DVD+RW, DVD+R, DVD-R and DVD-RW.
– CD-R and CD-RW cannot be played unless finalized.
– Some discs cannot be played depending on the recording
conditions such as PC environment and application software.
The characteristics and condition of the discs; materials,
scratches, curvature, and etc, may result in failure.
– Be sure to use only CD-R and CD-RW discs made by
reliable manufacturers.
– Do not use any non standard shaped discs (heart, etc.)
– Do not use disc with tape, scals, or paste on it, damage to
the unit may result.
– Do not use a disc printed on its surface by a commercially
available label printer.
2
Manufactured under license from Dolby Laboratories. “Dolby” and
the double-D symbol are trademarks of Dolby Laboratories.
This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Functional Overview
Front and Rear Panels
English
R/ T
– search forward* / go to the next
chapter or track
STANDBY/ON
– to turn this unit to standby mode or ON
S /Q
– search backward* / go to a previous
chapter or track
Disc Tray
/ OPEN/CLOSE
– to open/close the disc tray
B/ ; PLAY/PAUSE
– to start/interrupt playback
9 STOP
– to stop playback
NATURAL SOUND DVD PLAYER
DVD–E600
STANDBY/ON
/
/
* Press button for about two seconds.
COAXIAL
– connect to DIGITAL INPUT of your AV reciver
S-VIDEO
– connect to S-Video input of your TV
AUDIO OUT (Left/Right)
– connect to AUDIO inputs of your
AV receiver or stereo system
COMPONENT VIDEO
– connect to component video inputs of
your TV
OPTICAL
– connect to DIGITAL INPUT of your
AV receiver
AV
– connect to a TV with SCART
AC Power Cord
– connect to the AC outlet of the RX-E600
VIDEO
– connect to Video inputs
of your TV
SYSTEM CONNECTOR
– connect to the SYSTEM CONNECTOR
(DVD) of the RX-E600
SYSTEM
CONNECTOR
RECEIVER
COMPONENT VIDEO OUT
PR
PB
AV
Y
DIGITAL
OUT
AUDIO
OUT
VIDEO OUT
L
VIDEO
R
S VIDEO
COAXIAL
OPTICAL
E
Caution: Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
3
Functional Overview
Remote Control
TOP MENU/RETURN
– display the top-level disc
menu (DVD) / go back to
previous menu (VCD)
MENU
– access menu of a disc (DVD) /
switch PBC on/off (VCD)
– turn this unit ON or go to
standby-on mode
1
2
3
4
5
6
7
8
ON SCREEN
0
MENU
1 2 3 4
– (left/right/up/down) select an
item in the menu
ENTER/OK
– acknowledge menu selection
9
TOP MENU RETURN
SETUP
ON SCREEN
– access or remove player’s
On Screen Display menu
ENTER
OK
STOP
PLAY
PAUSE
SUBTITLE ANGLE ZOOM AUDIO
S
– search backward* / go to a
previous chapter or track
STOP ( 9 )
– stop playback
PLAY ( B )
– start playback
PAUSE ( ; )
– pause playback temporarily /
frame-by-frame playback
REPEAT
– repeat chapter, track, title,
disc / shuffle chapter, track
A-B
– repeat a specific segment
SCAN
– preview the content of a track
or whole disc (VCD) / play the
first 6 seconds or less of each
track (CD)
MUTE
– disable or enable sound output
* Press and hold button for about two seconds.
4
0-9 numeric buttons
– select numbered items in a
menu
REPEAT
A B
SCAN MUTE
DVD
SETUP
– access or remove player’s
setup menu
T
– search forward* / next
chapter or track
SUBTITLE
– subtitle language selector
ANGLE
– select DVD camera angle
ZOOM
– enlarge video image
AUDIO
– audio language and format
selector
Preparation
Analog Connections
Use audio/video cable supplied with this unit to connect
AUDIO OUT L (left) and R (right) jacks of this unit to
corresponding input jacks of your audio equipment such
as Stereo amplifier.
General Notes on connections
●
●
●
●
Never make or change connections with the power
switched on.
Depending on the equipment you wish to connect, there
are various ways you could connect this unit. Possible
connections are shown in the following drawings.
Please refer to the manuals of other equipment as
necessary to make the best connections.
Do not connect this unit via your VCR. The video quality
could be distorted by the copy protection system.
Do not connect this unit’s audio out jack to the phono in
jack of your audio system.
DIGITAL
OUT
AUDIO
OUT
VIDEO OUT
L
VIDEO
R
S VIDEO
COAXIAL
OPTICAL
E
L
R
(supplied)
R
Stereo
amplifier
L
1 CD/DVD
R
L
Digital Connections
This unit has COAXIAL and OPTICAL digital out jacks.
Connect one or both of them to your AV receiver
equipped with Dolby digital or MPEG decoder using
each specific cable (separate purchase).
DIGITAL
OUT
Left
speaker
Right
speaker
AUDIO
OUT
VIDEO OUT
L
VIDEO
R
S VIDEO
COAXIAL
OPTICAL
AV receiver
E
O
C
COAXIAL
IN
OPTICAL
IN
Subwoofer
Center speaker
Left main
speaker
Left rear
speaker
Right main
speaker
Right rear
speaker
You will need to set this unit’s digital output to All (see
‘DIGITAL OUTPUT’).
Note:
– If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a
strong, distorted sound or no sound at all. Make sure to
select the appropriate audio format at menu screen included
on the disc.
Pressing AUDIO once or more may change not only audio
languages but also audio formats, and the selected format
appears for several seconds on the status window.
5
English
Please refer to the RX-E600 manual for
instructions on connecting this unit to
the RX-E600 receiver.
Preparation
Video Connections
S-Video terminal <A>
The player has three types of video output jacks. Use one
of them in accordance with the input jacks of the
equipment to be connected.
S (separate) video connection achieves a clearer picture
than composite video connection by separating color
and luminance when transmitting signals. Use
commercially available S-video cable.
Note:
– If your AV receiver has video output jacks, connect your
receiver (and then to your TV) so that you can use one TV for
several different video sources (LD, VCR etc.) by simply
switching the input source selector of your receiver.
COMPONENT VIDEO OUT
PR
PB
AV
DIGITAL
OUT
AUDIO
OUT
VIDEO OUT
L
VIDEO
R
S VIDEO
OPTICAL
(supplied)
<A>
V
<B>
Use audio/video cable supplied with this unit when
connecting the player to a TV.
Component Video terminal <C>
Y
COAXIAL
Composite Video terminal <B>
E
Component video connection achieves high fidelity in
reproducing colors (better performance than S-video
connection), separating video signal into luminance (Y,
terminal color-coded as green), and color difference (Pb,
blue/Pr, red). Use commercially available coaxial cables.
Receiver (and TV) with component input is required.
Observe the color of each jack when connecting.
<C>
S
SCART Connection <D>
<D>
Use a SCART cable to connect this unit’s AV terminal to
a SCART terminal on your TV.
Note:
– Ensure that the “TV” indication on SCART cable is
connected to the TV set and “DVD” indication on SCART
cable is connected to this unit.
6
Preparation
1
2
3
PAL/NTSC Conversion
English
Inserting batteries into the
Remote Control
This player is equipped with a PAL/NTSC conversion
feature to convert the video output of the disc to match
your TV system. The conversions supported are as
below. To activate the conversion, refer to “TV TYPE”:
Open the battery cover by pressing in the tab, then lift off
the cover.
Insert batteries with the correct polarity as indicated by
the + and - symbols inside the battery compartment.
Close the cover.
Disc
Type
DVD
+
–
VCD
Format
PAL
Output format
Selected mode
PAL
MULTI
NTSC
PAL
NTSC
PAL
NTSC
PAL
NTSC
NTSC
PAL
PAL
NTSC
PAL
NTSC
PAL
NTSC
NTSC
–
+
CAUTION!
– Remove batteries if they are exhausted or not to be used
for a long time.
– Do not use old and new or different types of batteries in
combination.
– Batteries contain chemical substances, so they should be
disposed off properly and kept away from children.
Using the Remote Control
● Direct the remote control at the remote sensor of the DVD
player.
● Do not drop or give the remote control a shock.
● Do not leave the remote control in extremely hot or humid
places.
● Do not spill water or put anything wet on the remote
control.
Notes:
– “MULTI” can only be selected when using a TV that has
both the PAL and NTSC systems.
– Slight picture distortions may occur due to this
conversion. This is normal. Thus, the “MULTI” is most
suitable for the best picture quality.
Turning on the power
1
2
3
4
5
Connect the AC power cord to the power outlet.
Turn on the TV and your receiver.
Select the appropriate input source at the receiver that
was used to connect to this unit. Refer to the equipment
owner’s manual for detail.
Turn this unit on.
Set the TV to the correct Video IN channel. (eg. EXT1,
EXT2, AV1, AV2, AUDIO/VIDEO, etc. (Refer to your TV
owner’s manual for detail)
➜ The front display lights up and the default screen
appears on the TV.
Smart Power On/Off
When in STOP mode, the DVD player will switch to
standby mode after 15 minutes without any operations for
saving energy. It is easily reactivated by pressing the
POWER or PLAY on the remote control or the STANDBY/
ON button on the front panel.
7
Operation
SEARCH
Basic Playback
1
2
3
4
1
Press STANDBY/ON on the front panel to turn on the DVD
player.
Press / (OPEN/CLOSE) on the front panel to open disc
loading tray.
Place the chosen disc in the tray, with the label facing up.
Press / (OPEN/CLOSE) again to close the tray.
➜ After recognizing this disc, the player begin to
playback automatically.
➜ If you press PLAY when the tray is open, this unit
closes the tray and starts playback.
2
3
DVD
CD
VCD
SVCD
To search the contents in fast speed, press 2 or 1 for fast
forward/backward searching.
Press 2 or 1 again to increase the speed for searching.
Press PLAY to return to normal playback.
Slow Motion
DVD
1
2
3
To get a slow motion effect during playback, press 3 or
4.
Press 3 or 4 again, you can get different playback
forward/backward speeds.
Press PLAY to return to normal play back.
VCD
1
2
3
SVCD
To get a slow motion effect during playback, press 4.
Press 4 again, you can get different playback forward
speeds.
Press PLAY to return to normal play back.
Note: The SLOW BACKWARD function is not available for
VCD/Super VCD discs.
Notes:
– DVDs may have a region code. Your player will not play
discs that have a region code different from the region code
of your player.
– If ‘DISC LOCK’ is set to LOCK and the disc inserted is not
authorized, the 6-digit code must be entered and/or the disc
must be authorized (see ‘DISC LOCK’).
Audio control during playback
MUTE
1
2
DVD
VCD
CD
SVCD
Press MUTE to disable the sound output.
Press MUTE again to deactivate the mute.
Audio channel selection
General Operation
VCD
Note: All instructions set out below refer to the remote
control, unless otherwise stated.
1
Video control during playback
STOP
1
DVD
VCD
PAUSE/STEP
1
2
3
2
3
DVD
VCD
VCD
CD
SVCD
CD
SVCD
Press !1 or 2@ briefly during playback to go to the next
chapter/track or to return to the beginning of the currect
chapter/track respectively.
Press !1 twice briefly to step back to the previous
chapter/track.
To go directly to any chapter/track, enter the chapter/
track number using the numeric buttons and press
ENTER/OK.
Note: Long press of the !1 or 2@ till switch on backward or
forward search.
8
SVCD
To get a still picture, press PAUSE during playback.
To step forward to the next frame picture, press PAUSE
again.
➜ It resumes to the normal playback for CD.
To resume normal playback, press PLAY.
SKIP DVD
1
CD
You can resume the play from the point at which you
stopped last time, if you just press STOP once. It will start
from the beginning if you press STOP twice to stop
playback.
2
3
CD
SVCD
Super VCD has two stereo audio channels which are
used for playing karaoke or the audio language
selection. (for instance, you can choose one channel for
only the music background of the song while you play the
karaoke.)
Press AUDIO to select the audio channels you want.
VCD has only one stereo audio channel, you can select
STEREO, MONO LEFT, MONO RIGHT or MIX-MONO by
pressing AUDIO.
➜ STEREO: Output the left and right audio channels of
the disc through the left and right audio jacks
accordingly.
➜ MONO LEFT: Output the left audio channels of the
disc through the left and right audio jacks.
➜ MONO RIGHT: Output the right audio channels of the
disc through the left and right audio jacks.
➜ MIX-MONO: each of the audio jacks can output the
same audio effect as stereo.
Operation
Repeat and Shuffle
OSD (On-Screen Display)
● Each time you press REPEAT, the Repeat/Shuffle mode
changes as follows;
Chapter Repeat*
Repeat/Shuffle Off
Title Repeat
Shuffle Repeat
Shuffle
* This feature may not be available with some discs.
SVCD
VCD
CD
With PBC OFF,
● Each time you press REPEAT, the Repeat/Shuffle mode
changes as follows;
Track Repeat
Repeat/Shuffle Off
Repeat A-B
1
2
3
1
2
This function will provide some information about your
playing disc and a rough transferring speed of the video
data on the screen.
● Press ON SCREEN.
The Status window appears on the TV.
Title/Chapter/Track selection
1
2
3
Time Search
Disc Repeat
Shuffle Repeat
DVD
VCD
Shuffle
SVCD
1
CD
DVD-Video Discs: repeat a sequence in a title
Video and Audio CDs: repeat a sequence in a track
Press Repeat A-B at your chosen starting point.
Press Repeat A-B again at your chosen end point.
➜ The repeat sequence begins.
To exit the sequence, press Repeat A-B.
2
3
Disc Resume
1
2
3
DVD
VCD
CD
SVCD
This player can resume playback of the last 5 discs, even
if the disc was ejected or the power switched off.
Load one disc, which is one of the last 5 discs.
Press PLAY when DVD player is recognizing the disc. If
the information of this disc has been stored in the
memory of DVD player, it will be played back from the
stop point last time.
VCD
DVD
VCD
Press 34 to select “TT TIME” or “CH TIME”(DVD) or
“TRACK TIME” or “DISC TIME”(VCD).
➜ “TT TIME” refers to the total time of the current title,
and the “CH TIME” refers to the total time of the current
chapter.
Press ENTER/OK.
Enter hours, minutes and seconds from left to right using
the numeric buttons. (e.g. 0:34:27)
Audio/Subtitle/Angle
DVD
You can change “AUDIO”, “SUBTITLE” or “ANGLE” if
available on the disc you are playing.
Press 34 to select “AUDIO”, “SUBTITLE” or “ANGLE”.
Press ENTER/OK.
For Audio and Subtitle,
Press 34 to highlight your selection and press ENTER/
OK.
or
For Angle,
Select an angle using the numeric buttons.
Repeat/Time Display
1
2
3
DVD
Press 34 to select “TITLE” or “CHAPTER” (DVD) or
“TRACK” (VCD).
Press ENTER/OK.
Select a title, chapter or track number using the numeric
buttons.
DVD
VCD
Press 34 to select “REPEAT” or “TIME DISP.”.
Press ENTER/OK.
Press 34 to highlight your selection and press ENTER/
OK.
Time display
CD
Each time you press ON SCREEN, the time display
changes as follows;
Total Elapsed
Total Remain
Single Remain
Single Elapsed
9
English
DVD
Operation
Zoom
1
2
DVD
VCD
Changing the Audio Language and/or
format DVD
SVCD
The Zoom function allows you to change the image size.
Press ZOOM to activate the function.
➜ Use 341 2 to view other parts of the zoomed picture.
➜ Playback will continue.
➜ Zoom function is also effective when the playback is
paused.
Press ZOOM repeatedly to return to the original size.
Special DVD Features
● Press AUDIO repeatedly to select the different
languages.
Note: The function will be activated only if the DVD is
recorded with multi-language audio tracks.
Subtitles
DVD
SVCD
● Press SUBTITLE repeatedly to select the different
subtitles.
Note: The function will be activated, only if the DVD or Super
VCD is recorded with multi-subtitles.
Playing a Title
DVD
A DVD disc may have one or more titles. This depends on
the content (a movie, video clips, a drama series, etc.) on
the disc.
● After you load a disc, information about the content
shows on the screen waiting for your selection. You can
also press TOP MENU to turn back to the title menu
during playback.
➜ Press the appropriate numeric buttons or 341 2 to
highlight your selection.
➜ Press ENTER/OK to confirm.
Playing a Chapter
DVD
When you have selected a title, it may include one or
more chapters.
● Any time you want to watch another chapter during
playback, press MENU to turn back to the chapter menu
(If disc has chapter menu).
➜ Press the appropriate numeric buttons or 341 2 on
the remote control to highlight your selection.
➜ Press ENTER/OK.
➜ After a chapter has been selected, you also can press
¡!1 or 2@ to make a change.
Camera Angle
DVD
Some discs contain scenes which have been shot
simultaneously from various angles.
This DVD player allows you to select the desired camera
angle.
● Press ANGLE on your remote control.
Note: The function is available only for the DVD discs which
have several angles recorded.
10
Special VCD & SVCD Features
Playback Control (PBC)
1
2
3
PBC function allows you to enter the index menu which is
used to select a track after loading the VCD & SVCD disc.
If you want to activate the function during the playback or
after pressing STOP twice,
Press MENU to set the PBC On.
➜ Pay attention to the hint on the screen.
Use !1 or 2@ to select the page you like.
➜ If the items of the index menus are numbered, press
the appropriate numeric buttons.
➜ Press ENTER/OK.
Press RETURN to enter the index menu during the
playback.
Notes:
– The content of the index menu depends on the disc. Please
refer to the disc’s instructions for details.
– If the disc doesn’t include the PBC information, this
function will have no effect.
If you want to skip the index menu and playback
directly from the beginning,
1
Press MENU to switch off the function.
Operation
Preview Function
This function is used to divide a disc into six parts by
regular intervals and display them on one page to help
you preview the whole disc.
SELECT DIGEST TYPE:
TRACK DIGEST
DISK INTERVAL
TRACK INTERVAL
● After you enter the menu of any digest type,
➜ To quit preview function: Press 341 2 to highlight
EXIT and press ENTER/OK.
➜ To return to the previewing menu for selecting the
other digest type: Press 341 2 to highlight MENU and
press ENTER/OK.
Note: You can select “TRACK INTERVAL” only during
playback, with PBC Off.
1 TRACK DIGEST
This function will minimize the picture of every track in
order to display every six of these tracks on the screen to
help you know the content of every track on the disc.
- To choose the desired track, press 341 2 to highlight the
second line and input your selected track number next to
“SELECT”.
➜ Select the others from the current six by pressing the
!1 or 2@ to open the previous or next page and press
ENTER/OK.
- You can also select a track by highlighting the preview
screen using 341 2 and pressing ENTER/OK.
- To choose the desired track, press 341 2 to highlight the
second line and input your numerical selection next to
“SELECT” and press ENTER/OK.
- You can also select a track by highlighting the preview
screen using 341 2 and pressing ENTER/OK.
3 TRACK INTERVAL
This function is used to divide a single track into six parts
by regular intervals and display them on one page to help
you preview the selected track.
- To choose the desired track, please press 341 2 to
highlight the second line and input your numerical
selection next to “SELECT” and press ENTER/OK.
- You can also select a track by highlighting the preview
screen using 341 2 and pressing ENTER/OK.
11
English
● Press SCAN to enter previewing menu.
● Press 34 to highlight “TRACK DIGEST”, “DISC
INTERVAL” or “TRACK INTERVAL”.
● Press ENTER/OK to open one option.
2 DISC INTERVAL
Picture CD & MP3 Playback
●
●
●
●
●
●
●
●
●
●
This player can playback JPEG format pictures and MP3
files on a personally recorded CD-R/RW disc or
commercial CD, and is compatible with Kodak Picture
CD. This player does not support PROGRESSIVE JPEG.
Playback pictures or songs one by one automatically.
Album and track selection.
Repeat (disc / album / track / picture).
Select any music or pictures from the disc to playback
them together.
Maximum numbers of files in one folder are 500.
Maximum number of folders in one layer are 500.
Maximum nested directory is eight levels.
Maximum 13 characters are supported.
The file names, MP3, JPG, JPE, and JPEG, are
supported.
Maximum files Programmable is 100.
MP3 & JPEG Navigator
1
2
3
4
5
6
7
To select a different playback method, follow the steps
below.
At STOP mode, press SETUP to open the setup menu.
Press 1 2 to highlight PREFERENCE icon.
Press 4 to open the PREFERENCE menu.
Press 34 to highlight the MP3/JPEG NAV menu.
Press 2 to enter the menu.
Press 34 to highlight the WITHOUT MENU or WITH
MENU item.
➜ WITHOUT MENU: automatically playback all files in
according date sequence (MP3 only).
➜ WITH MENU: playback files in the selected folder.
Press ENTER/OK to confirm your selection.
Play Mode
General Operation
● If you choose WITH MENU in the Setup Menu (Please
refer to the MP3 & JPEG navigator below), the Picture
CD/MP3 CD menu will be shown on the screen before
playback.
● At any time during JPEG playback, press MENU to return
to the menu.
● To open the selected folder, press ENTER/OK.
● The menu shows six files or folders at a time. To move to
the next (or previous) page, press 2@ (or !1 ).
● You cannot record the MP3 audio output from digital
audio output jacks.
12
Auto Playback
If you choose WITHOUT MENU, the DVD player will
automatically play MP3 CD in sequence when it is
loaded.
Repeat / Shuffle
● When the Picture CD/MP3 CD menu is shown on the
screen, Press REPEAT repeatedly, the button beside
PLAY MODE will display different option,
➜ Repeat One: One file will be replayed time after time.
➜ Repeat Folder: All files in this folder will be replayed
time after time.
➜ Shuffle: All files in this folder will be played at random
without any repeat.
➜ Folder: All files in this folder will be played.
● If you press REPEAT during playback, the option will be
displayed on the screen accordingly.
● During Shuffle mode, you can skip tracks by pressing !1
or 2@.
Picture CD & MP3 Playback
Special JPEG Features
●
●
●
●
●
Picture CD is a disc with a collection of JPEG format
pictures, and all extension filenames should end with
‘.JPG’. The CD can be recorded on any computer, and
pictures may be from digital camera or scanner. If the
customers prefer, they can make this CD become a
Digital Album.
You can choose any general function introduced in
General Operation, besides, you also can,
Display the thumbnails of 12 pictures.
Zoom the picture.
Rotate the picture.
Flip the picture vertically or horizontally.
Scan pictures by different effects.
When displaying one picture on TV screen
● Press 341 2 to get different effects.
3: Flip the picture vertically.
4: Flip the picture horizontally.
1: rotate the picture anti-clockwise.
2: rotate the picture clockwise.
Wipe Effect
● Press ANGLE repeatedly to choose different wipe
effects.
Special MP3 Features
Function Introduction
“MP3” stands for “MPEG Audio Layer-3”. and is a part of
the MPEG standard. A CD can store up to 10 hours of
MP3 audio, which is nearly 10 times as much as an Audio
CD. Each song is recorded as a file. You can choose any
general function introduced in General Operation. You
can also choose different playback speeds.
Preview Function
1
English
Function Introduction
Playback with multi-angles
This function shows the content of the current folder or
the whole disc.
Press STOP during playback of JPEG pictures. You will
see the thumbnails of 12 pictures on the screen.
JPEG and MP3 simultaneous
playback
1
2
2
3
4
Press !1 or 2@ to display the other pictures on the next
or the previous page.
Press 341 2 to highlight one of them and press ENTER/
OK to playback, or,
Move the cursor to highlight
on the bottom of the
page to start playback from the first picture on the current
page.
Press MENU to go to the Picture CD/MP3 CD menu.
3
Firstly playback MP3 music according to the instructions
introduced in playback Selection.
Then select a picture to playback. Refer to the
instructions introduced in playback Selection.
➜ Now the pictures will be played back in sequence
together with MP3 music.
To quit simultaneous playback, press MENU to return to
the Picture CD/MP3 CD menu, then pictures will be
stopped. After that, press STOP, then MP3 music will be
stopped as well.
Note: In the function of JPEG and MP3 Simultaneous
Playback, !1 and 2@ are invalid for MP3.
Zoom picture
● During playback or pause, press ZOOM to display the
picture with different scales.
● Press 341 2 to view the rest of the zoomed picture.
13
Setup Menu
Basic Operation
1
2
3
4
5
PROGRAM (not for Picture CD/MP3)
Press SETUP in the STOP mode to enter the Setup Menu.
Press ENTER/OK to go to the next level submenu or
confirm your selection.
Press 1 2 to enter the submenu or return to the previous
menu.
Press 34 to highlight the desired menu.
Press SETUP to quit the setup menu.
➜ When you quit the setup menu, the settings will be
stored in the player’s memory even if the player is
switched to power off.
1
2
3
press 34 to choose “PROGRAM”.
Press 2 to move the cursor to the field of the submenu to
choose the item Input menu.
➜ Input menu: Enter the Program item.
Press ENTER/OK to enter the program page.
Input your favorite track
General Setup menu
1
Some settings need to be made in this menu. They are:
“DISC LOCK”, “PROGRAM”, “OSD LANGUAGE” and
“SCREEN SAVER”.
Follow the steps below:
GENERAL SETUP PAGE
DISK LOCK
PROGRAM
OSD LANGUAGE
SCREEN SAVER
2
3
Input valid track number by pressing the numeric
buttons.
Press 341 2 to move the cursor to the next selected
position.
➜ If the track number is more than ten, press 2@ to open
the next page and go on programing, or press 341 2 to
highlight NEXT button, and then press ENTER/OK.
Repeat this steps to input another track number until the
whole program is completed.
Remove a track
1
2
1
2
Press SETUP to enter the setup menu.
Press 1 2 to choose the GENERAL SETUP icon
.
DISC LOCK
1
2
3
When the disc is locked, the player will store its specific
code into the memory for future identification. For the next
playback, the DVD player will prompt you to enter the
password. Then, press ENTER/OK to load the disc.
Press 34 to highlight “DISC LOCK”.
Enter its submenu by pressing 2.
➜ Lock: Lock the disc being played.
➜ Unlock: unlock the disc.
Press 1 to return to the General Setup Page.
Press 341 2 to move the cursor to the track you want to
remove.
Press ENTER/OK or PLAY to remove this track from the
program menu.
Playback tracks
1
2
When programing is completed,
Press 341 2 to move the cursor to the START button.
Press ENTER/OK.
➜ DVD player will playback the selected tracks under
the programed sequence.
Quit the program playback
1
2
In the Program menu,
Press 341 2 to move the cursor to the EXIT button.
Press ENTER/OK to quit this menu.
Stop the program playback
● During playback of the programmed tracks, press STOP
once. Then after you press PLAY, the DVD player will
start resume-playback.
● Press STOP twice to cancel the resume-function.
Repeat the program playback
● During playback of the programmed tracks, press
REPEAT. The programed tracks can be played again.
Note: If you select Shuffle mode by pressing REPEAT several
times, the DVD player cancels program playback.
14
Setup Menu
2
3
4
5
Audio Setup menu
This option is to select a language for information
displayed on TV screen.
Press 34 to highlight “OSD LANGUAGE” in the General
Setup menu.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
language.
Press ENTER/OK to confirm.
Press 1 to return to the General Setup Page.
There are items included in Audio Setup Page such as
“SPEAKER SETUP”, “DIGITAL AUDIO SETUP”,
“EQUALIZER” and “3D”.
AUDIO SETUP PAGE
SPEAKER SETUP
DIGITAL AUDIO SETUP
EQUALIZER
3D
SCREEN SAVER
1
2
3
4
5
This function is used to turn the screen saver on or off.
Press 34 to highlight “SCREEN SAVER” in the General
Setup menu.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
item.
➜ On: In STOP or No DISC mode, if no actions are
performed within 5~6 minutes, the screen saver will be
activated.
➜ Off: Screen saver is disabled.
Press ENTER/OK.
Press 1 to return to the General Setup Page.
1
2
Press SETUP to enter the setup menu.
Press 1 2 to choose the AUDIO SETUP icon
.
SPEAKER SETUP
This menu contains setup options for your analog audio
output, such as “DOWNMIX”, “DRC” (Dynamic Range
Compression) etc. which makes the setup system
reproduce high quality surround sound.
DOWNMIX
Press 34 to highlight the “DOWNMIX”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
item.
● LT/RT
➜ This option should be used only if your DVD player is
connected to a Dolby Prologic decoder.
● STEREO
➜ This option will downmix Dolby Digital signals directly
into analogue stereo from L/R jacks.
● VIRTUAL SURROUND
➜ This option will reproduce the surround channels
virtually.
4 Press ENTER/OK.
5 Press 1 to return to the Audio Setup Page.
1
2
3
DRC (Dynamic Range Compression)
1
2
3
4
5
The DVD player will compress the dynamic range of its
sound output for late-night listening.
Press 34 to highlight “DRC”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
item.
➜ ON: Enable DRC.
➜ OFF: Disable DRC.
Press ENTER/OK.
Press 1 to return to the Audio Setup Page.
15
English
1
OSD LANGUAGE
Setup Menu
DIGITAL AUDIO SETUP
EQUALIZER (Sound Mode)
In this menu, you can set up the digital audio output
signal from the digital jacks, such as coaxial etc.
The “EQUALIZER” allows you to select from various
preset modes that control the frequency bands of sound
to optimize certain musical styles.
It greatly enhances the excitement and enjoyment of your
favourite music.
Press 34 to highlight the “EQUALIZER”.
Enter its submenu “SOUND MODE” by pressing 2.
Press 2.
Move the cursor by pressing 34 to highlight the selected
item.
➜ NONE: Play the disc under the original sound effect.
Press ENTER/OK.
Press 1 to return to the Audio Setup Page.
DIGITAL OUTPUT
1
2
3
4
5
Press 34 to highlight DIGITAL OUTPUT.
Enter its submenu by pressing 2.
Press 34 to highlight the selected item.
➜ All: Original digital signals output.
➜ PCM Only: If your receiver is PCM-compatible, or your
receiver can not decode MPEG-2 or Dolby Digital,
choose this option.
Press ENTER/OK.
Press 1 and return to the Audio Setup Page.
1
2
3
4
5
6
Note: If DIGITAL OUTPUT is set to “ALL”, all audio settings
except MUTE are invalid.
Note: The sound may be distorted if the selected sound mode
is incompatible with the disc contents.
In that case, select another sound mode or “NONE”.
LPCM OUTPUT
1
2
3
4
5
In this menu, you can select PCM digital output between
48kHz and 96kHz.
Press 34 to highlight the “LPCM OUTPUT”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
item.
➜ 48K: 96kHz (if available on disc) PCM data stream will
be converted to 48kHz.
➜ 96K: If the 96kHz disc is copy protected, the digital
output will be muted to comply with the standards.
Press ENTER/OK.
Press 1 to return to the Audio Setup Page.
3D (REVERB MODE)
1
2
3
4
5
6
16
The “3D” can simulate the echoes and frequency
response of some particular places so as to make you
feel like personally on the place. The choices are OFF,
CONCERT, LIVING ROOM, HALL, ARENA, and
CHURCH.
Press 34 to highlight the “3D”.
Enter its submenu “REVERB MODE” by pressing 2.
Press 2.
Move the cursor by pressing 34 to highlight the selected
item.
➜ OFF: Play the disc under the original sound effect.
Press ENTER/OK.
Press 1 to return to the Audio Setup Page.
Setup Menu
Video Setup menu
TV DISPLAY
English
There are items included in Video Setup menu such as
“TV TYPE”, “TV DISPLAY”, “CLOSED CAPTION”,
“COMPONENT”, “PROGRESSIVE” and “PICTURE
SETTING”.
4:3
PANSCAN
4:3
LETTERBOX
VIDEO SETUP PAGE
TV TYPE
TV DISPLAY
CLOSED CAPTIONS
COMPONENT
PROGRESSIVE
PICTURE SETTING
16:9
1
2
Press SETUP to enter the setup menu.
Press 1 2 to choose the VIDEO SETUP icon
Select the aspect ratio of the TV to be connected.
4:3 PANSCAN ➜ when you connect a normal TV to the
DVD player. Displays the wide picture on the whole TV
screen with a portion automatically cut off.
4:3 LETTERBOX ➜ when you connect a normal TV to the
DVD player. Displays a wide picture with bands
displayed on the upper and lower portions of the TV
screen.
16:9 ➜ when you connect a wide-screen TV to the DVD
player.
.
TV TYPE
1
2
3
4
5
Before viewing the DVD or VCD, ensure that the PAL or
NTSC setting of the system matches your TV set.
Press 34 to highlight “TV TYPE” in the Video Setup
menu.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight one option.
Press ENTER/OK.
Press 1 to return to the Video Setup Page.
Note: Choosing “NTSC” item indicates that the player will
output NTSC signals, Similarly, you can get PAL signals by
choosing the “PAL” option. The option “MULTI” means video
output depends on the format of the DVD or VCD discs.
Setup the item as follows,
1
2
3
4
5
Press 34 to highlight the “TV DISPLAY” option in the
Video Setup menu.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
item.
Press ENTER/OK.
Press 1 to return to the Video Setup Page.
17
Setup Menu
1
2
3
4
5
CLOSED CAPTION
PROGRESSIVE
Closed Captions are data that are hidden in the video
signal on specific discs, invisible without a special
decoder. The difference between subtitles and captions
is that subtitles are intended for hearing persons and
captions are for the hearing impaired. Subtitles rarely
show all of the audio. For example, captions show sound
effects (e.g., “phone ringing” and “footsteps”), while
subtitles don’t.
Before you select this function, please ensure that the
disc contains closed captions information and your TV
set also has this function.
Press 34 to highlight “CLOSED CAPTION” in the Video
Setup menu.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight one option.
➜ ON: Enable Closed Caption.
➜ OFF: Disable Closed Caption.
Press ENTER/OK.
Press 1 to return to the Video Setup Page.
This player’s COMPONENT video jack can output
progressive signals to a progressive signal compatible
TV for an extra high-quality picture.
Press 34 to highlight “PROGRESSIVE”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight one option.
➜ ON: Enable Progressive.
➜ OFF: Disable Progressive.
If you select “ON”, the player prompt you to comfirm your
selection.
Press ENTER/OK.
Press 1 to return to the Video Setup Page.
COMPONENT
1
2
3
4
5
In this menu, you can select whether to output YUV
signals from the COMPONENT jacks or to output RGB
signals from the AV jack (SCART).
Press 34 to highlight “COMPONENT”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34 to highlight one option.
➜ YUV: Output YUV signals from the COMPONENT
jacks.
➜ RGB: Output RGB signals from the AV jack (SCART).
Press ENTER/OK.
Press 1 to return to the Video Setup Page.
1
2
3
4
5
Notes on activating Progressive:
● Ensure that your TV has progressive scan.
● Connect with YPbPr video cable.
● When the Progressive is active, the VIDEO (CVBS) and S
VIDEO jacks do not output video signals.
● If there is no picture, wait 15 seconds for auto recover or
disactivate Progressive manually.
1 Open the disc tray by pressing / (OPEN/CLOSE)on the
front panel.
2 Press 1.
3 Press MUTE.
● You cannot activate Progressive when “COMPONENT” is
set to “RGB”.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625
PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE CONNECTION
TO THE “STANDARD DEFINITION” OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR VIDEO MONITOR
COMPATIBILITY WITH THIS MODEL 525P AND 625P DVD
PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE
CENTER.
This unit is compatible with the complete line of YAMAHA products,
including the projectors DPX-1000, LPX-510 and the plasma
monitor PDM-4210E.
18
Setup Menu
2
PASSWORD SETUP
In this menu, you can personalize your picture color by
adjusting brightness, contrast, tint and color (saturation).
Press 34 to highlight “PICTURE SETTING” in the Video
Setup menu.
Press 2 to open its submenu.
This item is used for the parental control and disc lock.
Enter your six digit password when a hint is displayed on
the screen.
PASSWORD SETUP PAGE
BRIGHTNESS
1
2
Press 34 to highlight “BRIGHTNESS”.
Press 2 to open the level bar.
BRIGHTNESS
3
4
PASSWORD
-1
Press 1 2 to increase and decrease the brightness level.
Press ENTER/OK to return to the PICTURE SETTING
menu.
CONTRAST
1
2
3
4
Press 34 to highlight “CONTRAST”.
Press 2 to open the level bar.
Press 1 2 to increase and decrease the contrast level.
Press ENTER/OK to return to the PICTURE SETTING
menu.
1
2
3
4
5
Press SETUP to enter the setup menu.
Press 1 2 to choose the PASSWORD icon
.
Press 4 to highlight “PASSWORD”.
Press 2 to highlight “CHANGE”.
Press ENTER/OK to open the Password Change Page.
OLD PASSWORD
NEW PASSWORD
CONFIRM PWD
TINT
1
2
3
4
Press 34 to highlight “TINT”.
Press 2 to open the level bar.
Press 1 2 to increase and decrease the tint level.
Press ENTER/OK to return to the PICTURE SETTING
menu.
COLOR (saturation)
1
2
3
4
Press 34 to highlight “COLOR”.
Press 2 to open the level bar.
Press 1 2 to increase and decrease the color level.
Press ENTER/OK to return to the PICTURE SETTING
menu.
Press 4 to repeatedly until the player prompt you to enter
the old password.
7 Enter the current 6 digit code.
8 If successful, the player will prompt for a new one.
9 After that, enter the new password again to reconfirm.
10 Press ENTER/OK to return to the Password Setup Page.
6
Notes:
– You can change the setup of parental control and load a
locked disc with a valid password being entered.
– If you forget your password, you can enter the default
password 842100, then you can input your password after
logging on.
19
English
1
PICTURE SETTING
Setup Menu
Preference Setup menu
DISC MENU language
There are options included in this menu such as
“AUDIO”, “SUBTITLE”, “DISC MENU”, “PARENTAL”,
“DEFAULT” and “MP3/JPEG NAV”.
DVD discs are available with multiple disc menu
languages. This option is used to select the default disc
menu language.
Press 34 to highlight “DISC MENU”.
Enter the submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
item.
➜ If you want to choose other languages, please refer to
the following instructions.
Press ENTER/OK.
Press 1 to return to the Preference Page.
PREFERNCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
MP3/JPEG NAV
1
2
3
Press STOP twice.
Press SETUP to enter the setup menu.
Press 1 2 to choose the PREFERENCE icon
1
2
3
4
5
Note: If your DVD disc doesn’t include the DISC MENU
language you have set, the player will use another recorded
language instead.
.
If you choose “OTHERS” in AUDIO, SUBTITLE or
DISC MENU menu,
AUDIO language
1
2
3
4
5
DVD discs are available with multiple audio languages.
Use this option to select the preferred default audio
language.
Press 34 to highlight “AUDIO”.
Enter the submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
option.
➜ If you want to choose other languages, please refer to
the instructions on the next page.
Press ENTER/OK.
Press 1 to return to the Preference Page.
Note: Your DVD disc may not include the audio language
which you set in the AUDIO menu. If so, the player will use
another audio language instead.
SUBTITLE language
1
2
3
4
5
DVD discs are available with multi-subtitle languages.
Use this option to select the preferred default subtitle
language.
Press 34 to highlight “SUBTITLE”.
Enter the submenu by pressing 2.
Move the cursor by pressing 34 to highlight the selected
option.
➜ If you want to choose other languages, please refer to
the following instructions.
Press ENTER/OK.
Press 1 to return to the Preference Page.
Note: Your DVD disc may not include the subtitle which you
set in the SUBTITLE menu. If so, the player will use another
subtitle language instead.
20
1
2
3
4
You can select other languages. Please do as follows,
Move the cursor by pressing 34 to highlight “OTHERS”.
Press ENTER/OK.
➜ The DVD player will prompt you to enter a language
code (Four digits).
Input a language code by pressing numeric buttons.
➜ Please look up the preferred language code in the
chapter LANGUAGE CODE, which can be found at the
end of this manual.
Press ENTER/OK.
Setup Menu
PARENTAL Control
3
No Parental Control
Parental Control is not activated. The Disc will be played
in full.
Select 8 ADULT item.
Press ENTER/OK.
1
2
3
If problems occur while setting up the DVD player, the
“DEFAULT” function can be used to reset all options to
the factory defaults and all your personal settings will be
erased.
Press 34 to highlight “DEFAULT”.
Highlight RESET by pressing 2.
Press ENTER/OK.
Note: When this function is activated, all setups will be reset
to factory defaults.
MP3/JPEG NAV
1
2
3
4
This menu allows you to select alternate settings when
you playback picture CD and MP3 CD.
Press 34 to highlight MP3/JPEG NAV.
Press 2 to enter the submenu.
Press 34 to highlight WITHOUT MENU or WITH MENU.
➜ WITHOUT MENU: playback all pictures or MP3 music
in sequence automatically.
➜ WITH MENU: playback pictures or MP3 music in the
selected folder.
Press ENTER/OK to confirm your selection.
Ratings 1 to 7:
Some discs contain scenes which are not suitable for
children. All scenes with a rating higher than you set will
be skipped during playback. However if the disc
contains alternate scenes, these will play automatically. If
not, the playback will stop and the six digits code will
need to be entered again.
21
English
1
2
DEFAULT Setup
DVD
Movies on DVDs may contain scenes which are not
suitable for children. Therefore, discs may contain
‘Parental Control’ information which applies to the
complete disc or to certain scenes on the disc. These
scenes are rated from 1 to 8, and alternative, more
suitable scenes are available on the disc. Ratings are
country dependent. The ‘Parental Control’ feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
● VCD, SVCD, CD have no level indication, so parental
control function has no effect on those kinds of discs.
This applies to most illegal DVD discs.
● You can follow the steps below to setup the parental
control:
1 Press 34 to highlight “PARENTAL”.
2 Move to its submenu by pressing 2.
3 Then use 34 to highlight a rating for the disc inserted.
4 Press ENTER/OK to confirm, then press 1 to return to the
Preference Page.
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed
below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and
contact the nearest authorized YAMAHA dealer or service center.
Problem
Solution
No power
– Check if the AC power cord is properly connected.
No picture
– Check if the TV is switched on.
– Check the video connection.
– If you did not use Progressive Scan connections (using the Y PB PR jacks
on the DVD Player) and you do not have a picture at the TV, please follow
the steps below to turn off Progressive Scan;
1. Press / (OPEN/CLOSE) to open the disc tray.
2. Press 1.
3. Then press MUTE to deactivate the Progressive. The DVD Player will
reset itself to Component/Interlaced video.
Distorted picture
– The disc is badly scratched or dirty.
– Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
Completely distorted picture or black/white
picture with DVD or Video CD
– Make sure the PAL/NTSC setting at the DVD player matches the video
signal of your television. (See PAL/NTSC CONVERSION)
No sound or distorted sound
– Adjust the volume.
– Check that the speakers are connected correctly.
No audio at digital output
– Check the digital connections.
– Check if your receiver can decode MPEG-2 and if not, please make sure
the digital output is set to PCM.
– Check if the audio format of the selected audio language matches your
receiver capabilities.
Disc can’t be played
–
–
–
–
No return to start-up screen when disc is
removed
– Reset the unit by switching the player off, then on again.
The player does not respond to the remote
control
–
–
–
–
Buttons do not work
– In order to completely reset the player, unplug the AC cord from the AC
outlet.
Player does not respond to some operating
commands during playback
– Operations may not be permitted by the disc. Refer to the instructions of the
disc.
DVD Video player cannot read CDs/DVDs
– Use a commonly available cleaning CD/DVD to clean the lens before
sending the DVD Video player for repair.
Cannot record MP3
– SCMS copy protected discs cannot be recorded digitally. Try recording by
analog jacks.
22
The DVD+R/DVD+RW/DVD-R/DVD-RW/CD-R/CD-RW must be finalized.
Ensure the disc label is facing up.
Check if the disc is defective by trying another disc.
If you have recorded this particular Picture CD or MP3 CD yourself, please
ensure that your disc contains at least about 6~10 pictures or 3~5MP3
music tracks before using it with the player.
Aim the remote control directly at the sensor on the front of the player.
Reduce the distance to the player.
Replace the batteries in the remote control.
Insert the batteries with their polarities (+/– signs) as indicated.
Specifications
AUDIO PERFORMANCE
DVD Video
Video CD & SVCD
CD
PICTURE CD
CD-R, CD-RW
DVD+R, DVD+RW
DVD-R, DVD-RW
DA Converter
Signal-Noise (1 kHz)
Dynamic range (1 kHz)
DVD
24 bit
105 dB
100 dB
fs 96 kHz
fs 48 kHz
SVCD
fs 48 kHz
fs 44.1 kHz
CD/VCD
fs 44.1 kHz
Distortion and Noise (1 kHz)
0.003%
VIDEO PERFORMANCE
Video (CVBS) Output
S-Video output
RGB (SCART) output
Component video output
1 Vpp into 75 ohm
Y: 1 Vpp into 75 ohm
C: 0.286 Vpp into 75 ohm
(U.S.A., Canada and Korea models)
0.3 Vpp into 75 ohm (Other models)
0.7 Vpp into 75 ohm
Y: 1 Vpp into 75 ohm
Pb/Cb Pr/Cr: 0.7 Vpp into 75 ohm
AUDIO FORMAT
Digital
Mpeg/ Dolby Digital
PCM
MP3(ISO 9660)
Compressed Digital
16, 20, 24 bits
fs, 44.1, 48, 96 kHz
24, 32, 56, 64, 96, 128, 256 kbps
fs, 16, 22.05, 24, 32, 44.1, 48 kHz
English
PLAYBACK SYSTEM
2 Hz- 44 kHz
2 Hz- 22 kHz
2 Hz- 22 kHz
2 Hz- 20 kHz
2 Hz- 20 kHz
TV STANDARD (PAL/50 Hz) (NTSC/60 Hz)
Number of lines
Playback
625
Multistandard
525
(PAL/NTSC)
CONNECTIONS
SCART
Y Output
Pb/Cb Output
Pr/Cr Output
S-Video Output
Video Output
Audio Output (L+R)
Digital Output
Euroconnector
Cinch (green)
Cinch (blue)
Cinch (red)
Mini DIN, 4 pins
Cinch
Cinch
1 coaxial, 1 optical
IEC958 for CDDA / LPCM/ MPEG1
IEC1937 for MPEG 2 and Dolby Digital
Analog Sound Stereo
CABINET
Dimensions (W x H x D)
Weight
217 x 108 x 346 mm
Approx. 2.5 Kg
POWER SUPPLY
Specifications subject to change without prior notice.
Power inlet
Power usage
Power usage standby
230 V, 50 Hz
Approx. 12 W
<1W
Maintenance
Cleaning the Cabinet
● Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol, spirits,
ammonia or abrasives.
Cleaning Discs
● When a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the center out. Do not wipe in a
circular motion.
● Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analog records.
23
Language Code
These pages can be used to select other languages.This does not affect the options in “AUDIO”, “SUBTITLE” or
“DISC MENU”.
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Avestan
Aymara
Azerbaijani
Bashkir
Basque
Belarusian
Bengali
Bihari
Bislama
Bokmål, Norwegian
Bosnian
Breton
Bulgarian
Burmese
Castilian, Spanish
Catalan
Chamorro
Chechen
Chewa; Chichewa; Nyanja
Chichewa; Chewa; Nyanja
Chinese
Chuang; Zhuang
Church Slavic; Slavonic;
Church Slavonic; Church
Chuvash
Cornish
Corsican
Croatian
Czech
Danish
Dutch
Dzongkha
English
Esperanto
Estonian
Faroese
Fijian
Finnish
French
Frisian
Gaelic; Scottish Gaelic
Gallegan
Georgian
24
6566
6565
6570
8381
6577
6582
7289
6583
6569
6589
6590
6665
6985
6669
6678
6672
6673
7866
6683
6682
6671
7789
6983
6765
6772
6769
7889
7889
9072
9065
6785
6785
6786
7587
6779
7282
6783
6865
7876
6890
6978
6979
6984
7079
7074
7073
7082
7089
7168
7176
7565
German
Gikuyu; Kikuyu
Greek,
Guarani
Gujarati
Hausa
Hebrew
Herero
Hindi
Hiri Motu
Hungarian
Icelandic
Ido
Indonesian
Interlingua (International)
Interlingue
Inuktitut
Inupiaq
Irish
Italian
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Khmer
Kikuyu; Gikuyu
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Kwanyama; Kuanyama
Lao
Latin
Latvian
Letzeburgesch;
Limburgan; Limburger;
Limburger; Limburgan;
Limburgish; Limburger;
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Malay
Malayalam
Maltese
Manx
6869
7573
6976
7178
7185
7265
7269
7290
7273
7279
7285
7383
7379
7368
7365
7369
7385
7375
7165
7384
7465
7486
7576
7578
7583
7575
7577
7573
8287
7589
7586
7579
7574
7585
7574
7679
7665
7686
7666
7673
7673
7673
7678
7684
7666
7775
7771
7783
7776
7784
7186
Language Code
These pages can be used to select other languages.This does not affect the options in “AUDIO”, “SUBTITLE” or
“DISC MENU”.
7773
7782
7772
7779
7778
7865
7886
7886
7868
7882
7871
7869
8369
7868
7879
7866
7878
7889
7878
7967
6785
6785
6785
7982
7977
7983
7983
8073
8065
7065
8076
8084
7967
8083
8185
8277
8279
8278
8285
8377
8371
8365
8367
7168
8382
8378
8368
8373
8375
8376
8379
Sotho, Southem
South Ndebele
Spanish; Castilian
Sundanese
Swahili
Swati
Swedish
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Turkish
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Walloon
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zhuang; Chuang
Zulu
English
Maori
Marathi
Marshallese
Moldavian
Mongolian
Nauru
Navaho, Navajo
Navajo; Navaho
Ndebele, North
Ndebele, South
Ndonga
Nepali
Northern Sami
North Ndebele
Norwegian
Norwegian Bokmål; Bokmål,
Norwegian Nynorsk;
Nyanja; Chichewa; Chewa
Nynorsk, Norwegian;
Occitan (post 1500); Proven
Old Bulgarian; Old Slavonic;
Old Church Slavonic; Old
Old Slavonic; Church
Oriya
Oromo
Ossetian; Ossetic
Ossetic; Ossetian
Pali
Panjabi
Persian
Polish
Portuguese
Provençal; Occitan (post)
Pushto
Quechua
Raeto-Romance
Romanian
Rundi
Russian
Samoan
Sango
Sanskrit
Sardinian
Scottish Gaelic; Gaelic
Serbian
Shona
Sindhi
Sinhalese
Slovak
Slovenian
Somali
8384
7882
6983
8385
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9065
9085
25
0100DVD-E600_EB_cover.fm Page 1 Monday, August 23, 2004 4:58 PM
EB
DVD-E600
©2004
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
Printed in Malaysia
WD90090
DVD-E600
DVD PLAYER
LECTEUR DE DVD
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES