Motorola Q - uick Start Instruction manual

DS9208
DS6708 Poster
Quick Start Guide
http://www.motorola.com/ds9208
CORD ATTACHMENT
See Product Reference Guide
for detailed information
1
BLACK
2
PANTONE 285
3
1
2
3
4
POST IN WORK AREA
4
LED Indicators
Scan Window
Scan Trigger
Beeper
WALL MOUNTING
TABLE TOP MOUNTING
Inserting Scanner
Removing Scanner
HOST INTERFACES
NOTE: Cables may vary depending on configuration
IBM 46XX
Keyboard Wedge
USB
RS-232
Power supply optional
TROUBLESHOOTING
Scanner not working
No power to scanner
Scanner not decoding bar code
Incorrect interface cable used
Check system power;
ensure power supply,
if required, is connected
Interface/power cables are loose
Ensure that correct
interface cable is used
Ensure all cable connections
are secure
Scanner not programmed
for bar code type
Bar code unreadable
Ensure scanner is programmed
to read type of bar code being
scanned
EnsEnsure bar code is not defaced;
try scanning test bar code of same
bar code typeure bar code is not defaced;
try scanning test bar code of same
bar code type
Scanner decoding bar code, but data not transmitting to host
Scanned data incorrectly displayed on host
Scanner not programmed for correct host interface
Scanner not programmed for correct host interface
Scan appropriate host parameter bar codes
Interface cable is loose
Ensure all cable connections are secure
Distance between scanner
and bar code incorrect
Scan appropriate host parameter bar codes
Perforation
DS9208 PROGRAMMING BAR CODES
Set Defaults
Enter Key (Carriage Return/Line Feed)
IBM 46XX Host Types
SET DEFAULTS
<DATA><SUFFIX 1>
PORT 5B
Keyboard Wedge Host Types
USB Host Types
HID KEYBOARD EMULATION
PORT 9B
SNAPI WITH IMAGING
IBM PC/AT and IBM PC COMPATIBLE
PORT 17
Scan ONE of the following country types
IBM HAND-HELD USB
SNAPI WITHOUT IMAGING
NORTH AMERICAN
ITALIAN
FRENCH
SWEDISH
RS-232 Host Types
STANDARD RS-232
NIXDORF RS-232 MODE B
FRENCH CANADIAN
ICL RS-232
FUJITSU RS-232
GERMAN
NIXDORF RS-232 MODE A
UK ENGLISH
OPOS/JPOS
SPANISH
JAPANESE
Move scanner closer to
or further from bar code
DS9208
OPTIMUM SCANNING
Hand-Held Scanning
Hands-Free Scanning
Aiming
DS6708 Poster
BLACK
012345
PANTONE 285
AVOID EXTREME WRIST ANGLES
OPTIMUM ARM POSITION
AVOID BENDING AND REACHING
AVOID BENDING
AVOID EXTREME
WRIST ANGLES
AVOID REACHING
Alternate left and right hands
taking breaks and task rotation
recommended
BEEPER INDICATIONS
LED INDICATIONS
Standard Use
Hand-Held Scanning
Low/medium/high beep
Short medium beep
Power up
4 long low beeps
Bar code decoded
Off
Transmission error
detected; data is
ignored
Scanner is on
and ready to scan,
or no power to
scanner
Red
Bar code is
successfully
decoded
Transmission
error
Hands-Free (Presentation) Scanning
Parameter Menu Scanning
High/low/high/low beep
Green
High/low beep
Successful
parameter
setting
Off
Low/high beep
Correct programming
sequence performed
Green
No power to
scanner
Incorrect
programming
sequence or
“Cancel” bar code
scanned
Off Momentarily
Scanner is ready
to scan
Bar code is
successfully
decoded
Red
Transmission Error
Local Contact:
123SCAN2
123Scan2 is an easy-to-use, PC-based software tool that enables rapid and easy customized setup via a bar code or USB
cable. For more information, visit: http://www.motorola.com/123Scan2.
Perforation
DS9208
REGULATORY INFORMATION
© 2011 MOTOROLA SOLUTIONS, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the application or
use of any product, circuit, or application described herein. No license is granted, either expressly or by
implication, estoppel, or otherwise under any patent right or patent, covering or relating to any
combination, system, apparatus, machine, material, method, or process in which Motorola products
might be used. An implied license exists only for equipment, circuits, and subsystems contained in
Motorola products. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are
trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
All other trademarks are the property of their respective owners.
This Motorola Product may include Motorola Software, Commercial Third Party Software, and Publicly
Available software. Refer to Product Reference Guide for complete copyright, conditions and disclaimer
information.
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there
is a problem with the equipment, they will contact Motorola Solutions Support at:
http://supportcentral.motorola.com.
For the latest version of this guide go to: http://supportcentral.motorola.com.
Waste Electrical and Electronic Equipment (WEEE)
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow
the recommendations below. Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety programs to prevent
employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
This guide applies to Model Number DS9208
All Motorola devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website:
http://supportcentral.motorola.com
Any changes or modifications to Motorola equipment, not expressly approved by
Motorola, could void the user’s authority to operate the equipment.
Declared maximum operating temperature: 40o C / 104o F
Radio Frequency Interference Requirements
Note: This equipment has been tested and
found to comply with the limits for a Class B
Tested to comply
with FCC Standards
digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
FOR HOME OR OFFICE USE
reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準に基づくクラスB情
報技術装置です。
この装置は、家庭環境で使用することを目的としていますが、
この装置がラ
ジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。
This is a Class B product based on the standard of the Voluntary Control Council
for Interference from Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic environment, it may cause radio
interference. Install and use the equipment according to the instruction manual.
Korea Warning Statement for Class B ITE
Class
User’s Guide
Class B
This device obtained EMC registration mainly for home use
(Broadcasting
(Class B) and may be used in all areas.
Communication
Device for Home Use)
기 종 별
B급 기기
(가정용 방송통신기기)
사용자 안내문
이 기기는 가정용(B급)으로 전자파적합등록을
한 기기로서 주로 가정에서 사용하는 것을 목적
으로 하며, 모든 지역에서 사용할 수 있습니다.
Power Supply
Use ONLY a LISTED Motorola, Type no. PWRS-14000 (5Vdc, 850mA), direct plug-in
power supply, marked Class 2 or LPS (IEC60950-1, SELV). Use of alternative Power
Supply will invalidate any approvals given to this unit and may be dangerous.
LED Devices
Complies with IEC/EN60825-1:2001 & EN 62471: 2006 and IEC62471: 2008.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Marking and European Economic Area (EEA)
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Motorola'ya
iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:
Statement of Compliance
Motorola Solutions, Inc.
One Motorola Plaza Holtsville, New York 11742-1300, USA
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks
or registered trademarks of Motorola Trademark Holdings, LLC and are used under
license. All other trademarks are the property of their respective owners.
© 2011 Motorola Solutions, Inc. All rights reserved.
72-140088-01 Revision A January 2011
DS9208
Motorola hereby declares that this device is in compliance with all the applicable
Directives, 2004/108/EC and 2006/95/EC. A Declaration of Conformity may be
obtained from http://www.motorola.com/doc
EAS
System integrator to ensure final product is compliant with all applicable EU
Directives.
Caution - use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous light exposure.
http://www.motorola.com/ds9208
Recommended Usage Guide