Epson ELPDC04 High Resolution Document Camera User`s guide

elpdc04.book Page i Tuesday, February 12, 2002 8:32 AM
EPSON ELPDC04
High Resolution Document Camera
®
User’s Guide
elpdc04.book Page ii Tuesday, February 12, 2002 8:32 AM
Important Safety Information
WARNING: Never open any cover on the document camera. Dangerous electrical voltages inside the document
camera can severely injure you. Do not attempt to service this product yourself. Refer all servicing to qualified
service personnel.
WARNING: The document camera and its accessories come packaged in plastic bags. Keep plastic bags away from
small children to avoid any risk of suffocation.
Caution: Never attempt to replace the lamps. Refer all lamp servicing to qualified service personnel.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for
use with this EPSON product. EPSON is not responsible for any use of this information as applied to other
products.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third
parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any
options or any consumable products other than those designated as Original EPSON Products or EPSON
Approved Products by SEIKO EPSON CORPORATION.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
PrivateLine and Presenters Club are registered trademarks and EPSON Connection is a service mark of Epson
America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2002 by Epson America, Inc.
Printed on recycled paper.
ii
1/02
CPD-13518
elpdc04.book Page iii Tuesday, February 12, 2002 8:32 AM
C
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Getting the Most from Your Document Camera . . . . . . . . . . 2
Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 3
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1
Setting Up the Document Camera . . . . . . . . . . . 5
2
Using the Document Camera . . . . . . . . . . . . . . . 17
Unpacking the Document Camera . . . . . . . . . . . . . . . . . . . . . 6
Installing Batteries in the Remote Control . . . . . . . . . . . . . . . 7
Positioning the Document Camera. . . . . . . . . . . . . . . . . . . . . 8
Unfolding the Document Camera . . . . . . . . . . . . . . . . . . . . . 9
Connecting to a Projector or TV/Computer Monitor. . . . . . 11
Connecting the RGB Video Cable . . . . . . . . . . . . . . . . . 11
Connecting the RCA Cable . . . . . . . . . . . . . . . . . . . . . . 12
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting a Mouse to the Document Camera . . . . . . . . . . 14
Adjusting the Camera DIP Switches . . . . . . . . . . . . . . . . . . . 15
Turning On Your Equipment. . . . . . . . . . . . . . . . . . . . . . . . 18
Turning On the Document Camera . . . . . . . . . . . . . . . 18
What To Do If You See a Blank Screen . . . . . . . . . . . . . 19
Switching Between Picture Sources. . . . . . . . . . . . . . . . . . . . 20
Adjusting the Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
iii
elpdc04.book Page iv Tuesday, February 12, 2002 8:32 AM
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Zooming and Focusing Your Image . . . . . . . . . . . . . . . . 22
Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 23
Adjusting the White Balance . . . . . . . . . . . . . . . . . . . . . 23
Using the Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Pausing the Main Display. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adjusting Settings with the On-Screen Display . . . . . . . . . . 24
Using the Camera Head as a Conventional Video Camera . . 26
Using the Image Mate Software . . . . . . . . . . . . . . . . . . . . . . 26
Turning Off and Storing the Document Camera . . . . . . . . . 27
3
Maintaining and Transporting the
Document Camera . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning the Lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cleaning the Document Camera Case . . . . . . . . . . . . . . . . . 33
Transporting the Document Camera . . . . . . . . . . . . . . . . . . 34
4
5
iv
Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Solving Problems with the Image . . . . . . . . . . . . . . . . . . . . . 36
Solving Problems with the Remote Control . . . . . . . . . . . . . 37
Where to Get Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Telephone Support Services . . . . . . . . . . . . . . . . . . . . . . 38
Technical Specifications . . . . . . . . . . . . . . . . . . . . . 39
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . . 41
elpdc04.book Page v Tuesday, February 12, 2002 8:32 AM
6
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 43
Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . . 46
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . 47
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . 48
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
v
elpdc04.book Page 1 Tuesday, February 12, 2002 8:32 AM
W
Welcome
Your versatile EPSON® ELPDC04 High Resolution Document
Camera can be connected to most types of projectors and display
devices. From boardrooms to auditoriums, you can show fine detail
with a large variety of presentation materials.
Your document camera captures images at a resolution of
1024 × 768 pixels with a maximum shooting area of 13.4 × 9.9 in.
(340 × 252 mm). With its 10× zoom capability and true XGA
resolution, even 10 point type can be read clearly. And the document
camera’s support for RGB and composite video provides additional
versatility.
You can connect the document camera to a wide range of computers,
including IBM® compatible PCs and laptops, Apple® Macintosh,®
Power Macintosh™ series (including G3 and G4 systems),
PowerBook® computers, many iMac™ and iBook™ series systems, and
high-end workstations such as the Sun® SPARCstation.™
Welcome 1
elpdc04.book Page 2 Tuesday, February 12, 2002 8:32 AM
Getting the Most from Your
Document Camera
Depending on your presentation, you can take advantage of any or all
of these options:
■
Connecting to a projector or TV/computer monitor
The document camera requires an output device, such as a
projector or TV/computer monitor, to display its image. To
connect the document camera to these devices, see page 11.
■
Connecting to a laptop or desktop computer
You can connect a video output source, such as a laptop or
desktop computer, to the document camera. This is especially
useful if your projector has only one video input port. See page 13
for more information.
■
Using the remote control
The remote control lets you control the lamps, zoom and focus
your image, and switch the display from the camera to a
computer. See Chapter 2 for details.
Using Your Documentation
This book contains all the information you need to set up and use
your document camera. Please follow these guidelines as you read
through it:
2
Welcome
■
Warnings must be followed carefully to avoid bodily injury.
■
Cautions must be observed to avoid damage to your equipment.
■
Notes contain important information about your document
camera.
elpdc04.book Page 3 Tuesday, February 12, 2002 8:32 AM
Getting More Information
Need tips on giving presentations or more information about your
document camera? Here’s where you can look for help:
■
http://www.presentersonline.com
Includes a library of articles covering presentation tips, tricks, and
technology. The site provides templates, clip art, and sound clips,
as well as Presenters Services to use on the road. Even more
resources and services are available if you register to join the
Presenters Club®—and it’s free.
■
http://support.epson.com
Download FAQs and e-mail your questions to EPSON support.
If you still need help after checking this User’s Guide and the sources
listed above, you can use the EPSON PrivateLine® Support service to
get help fast. Call (800) 637-7661 and enter the PIN on the card
included with your document camera. Or take advantage of EPSON’s
electronic support services 24 hours a day. See page 38 for more
information.
Registration
To register, simply fill out and return the enclosed registration card.
Registering allows EPSON to better understand and meet your needs.
If you want, you can also receive special updates on new accessories,
products, and services.
Welcome 3
elpdc04.book Page 4 Tuesday, February 12, 2002 8:32 AM
4
Welcome
elpdc04.book Page 5 Tuesday, February 12, 2002 8:32 AM
1
Setting Up the
Document Camera
T
his chapter explains how to set up the document camera for a video
presentation. You’ll find instructions for:
■
Unpacking the document camera
■
Installing batteries in the remote control
■
Positioning the document camera
■
Unfolding the document camera
■
Connecting to a projector or TV/computer monitor
■
Connecting to a computer
■
Connecting a mouse to the document camera
■
Adjusting the document camera’s DIP switches
Setting Up the Document Camera 5
elpdc04.book Page 6 Tuesday, February 12, 2002 8:32 AM
Unpacking the Document Camera
After unpacking the document camera, make sure you have all the
items shown below:
batteries
remote control
document camera
RGB video cable
Image Mate™
CD-ROM
mouse
power cord
RCA cable
USB cable
Save all the packaging in case you need to ship the document camera
later. Always use the original packaging (or equivalent) when you need
to send the document camera to another location. For transportation
instructions, see page 34.
6
Setting Up the Document Camera
elpdc04.book Page 7 Tuesday, February 12, 2002 8:32 AM
Installing Batteries in the
Remote Control
Before using the remote control, install its batteries.
1. Press down on the battery
cover and slide it off.
2. Insert two AAA batteries as
shown.
3. Replace the battery
compartment cover.
caution
When replacing batteries,
take the following
precautions:
■ Don’t mix old and new
batteries.
■ Replace batteries as soon as
they run out. If the
batteries leak, wipe away
battery fluid with a soft
cloth. If fluid gets on your
hands, wash them
immediately.
■ Don’t expose batteries to
heat or flame.
■ Dispose of used batteries
according to local
regulations.
■ Remove batteries if you
won’t be using the
document camera for a
long period of time.
Setting Up the Document Camera 7
elpdc04.book Page 8 Tuesday, February 12, 2002 8:32 AM
Positioning the Document Camera
caution
Don’t hold or lift the
document camera by the
camera head arm or lighting
unit arms; this may damage
them.
Before connecting the document camera, you need to decide where to
place it. Wherever you place it, be sure to follow these guidelines:
■
Place the document camera on a sturdy, level surface.
■
Make sure there is plenty of space for ventilation around and
under the document camera.
■
Make sure the document camera is within 10 feet (3 m) of a
grounded electrical outlet or extension cord, and within 5 feet
(1.5 m) of your output source.
■
Make sure you are within 23 feet (7 m) of the front or back of the
document camera to use the remote control.
■
With the control panel facing you, place the document camera
directly in front of you. Otherwise, items you place on the stage
may appear upside-down.
head arm
lighting arm
stage
lighting arm
control panel
Most presenters find it convenient to place the document camera in
front of the audience. This lets the presenter stand in the front of the
room, face the audience, and remain close enough to the equipment to
be able to control it.
8
Setting Up the Document Camera
elpdc04.book Page 9 Tuesday, February 12, 2002 8:32 AM
Unfolding the Document Camera
Follow these steps to unfold the document camera:
1. Raise the camera arm until you hear a click, then lower it slightly
until it locks into place.
2. Rotate the camera head so that the lens faces the stage
(downward).
3. Raise the right lighting arm, as shown, until it stops.
camera head
lighting arm
stage
Setting Up the Document Camera 9
elpdc04.book Page 10 Tuesday, February 12, 2002 8:32 AM
4. Rotate the lighting units forward, as shown, until they stop.
lighting unit
lighting unit
5. Tilt the lighting arms outward until they stop; then position the
lighting units so that they face the stage (downward).
10
Setting Up the Document Camera
elpdc04.book Page 11 Tuesday, February 12, 2002 8:32 AM
Connecting to a Projector or
TV/Computer Monitor
You can connect the document camera to any projector or monitor
that has a standard RGB video or composite video input port.
EPSON projectors support both connections. Most computer
monitors support only RGB video, while many television monitors
support composite video. Follow the instructions below to connect
the document camera to your output device with an RGB video cable
or an RCA cable.
Connecting the RGB Video Cable
Before you start, make sure your document camera and projector or
computer monitor are turned off.
1. Connect one end of the RGB video cable to the document
camera’s RGB OUT port.
projector
RGB OUT
AC IN
POWER
ON
RS-232C
RGB OUT
VIDEO
OUT
RGB IN
note
The RGB video input port on
the projector or monitor may
be labeled “computer,” or
“video in.”
USB
0
1
OFF
ABC
or
monitor
2. Connect the other end of the RGB video cable to the RGB video
input port on the projector or computer monitor.
3. Tighten the screws on the connectors.
Setting Up the Document Camera 11
elpdc04.book Page 12 Tuesday, February 12, 2002 8:32 AM
Connecting the RCA Cable
Before you start, make sure your document camera and projector or
TV are turned off.
1. Connect one end of the RCA cable to the document camera’s
VIDEO OUT port.
video out
AC IN
POWER
ON
RS-232C
RGB OUT
projector
VIDEO
OUT
RGB IN
USB
0
1
OFF
ABC
or
TV
2. Connect the other end of the RCA cable to the RCA input port
on the projector or TV.
12
Setting Up the Document Camera
elpdc04.book Page 13 Tuesday, February 12, 2002 8:32 AM
Connecting to a Computer
The document camera comes with one RGB video input port. This
can be used to connect a laptop or desktop computer to the document
camera.
This is especially useful if your projector has only one input port. You
can connect a computer to the document camera’s RGB input port as
described below, and connect the document camera to the projector’s
input port as described on page 11. This way, you can use the
camera’s remote control to switch between picture sources. Follow the
instructions on page 20 to switch between the sources.
Before you start, make sure your document camera and computer are
turned off.
1. Connect one end of the RGB video cable to the document
camera’s RGB IN port.
laptop
AC IN
POWER
ON
RS-232C
RGB OUT
VIDEO
OUT
RGB IN
USB
0
1
OFF
ABC
or
computer
2. Connect the other end of the RGB video cable to your computer’s
RGB video output (monitor) port.
3. Tighten the screws on the connectors.
Setting Up the Document Camera 13
elpdc04.book Page 14 Tuesday, February 12, 2002 8:32 AM
Connecting a Mouse to the Document
Camera
The included mouse functions as a pointing device. It also gives you
access to the document camera’s on-screen display, which controls
many of the features that are selectable from the remote control. To
connect the mouse, follow the instructions below.
1. Make sure your document camera is turned off.
2. Connect the mouse cable to the RS-232C port on the back of the
document camera.
3. Make sure DIP switch C is set to 0 (up). If it is not, follow the
instructions on page 15 to change the DIP switch setting.
AC IN
POWER
ON
RS-232C
RGB OUT
VIDEO
OUT
RGB IN
USB
0
1
ABC
OFF
RS-232C port
14
Setting Up the Document Camera
elpdc04.book Page 15 Tuesday, February 12, 2002 8:32 AM
Adjusting the Camera DIP Switches
The document camera has four DIP switches that control special
settings. Refer to the table below to make sure they are set correctly for
your configuration.
DIP switches
0
1
ABC
AC IN
POWER
RGB OUT
RS-232C
ON
VIDEO
OUT
RGB IN
USB
0
1
ABC
OFF
DIP Switch
0
1
Function
—
—
—
Factory use only.
A
NTSC*
PAL
Selects the TV video output
format. Select NTSC for US
model TV sets and PAL for
European TV sets.
B
60 Hz*
50 Hz
Selects the shutter frequency. If
the image starts to flicker, try
setting the shutter frequency
to 50.
C
Mouse*
RS-232C
Selects the communication
mode of the RS-232C port. To
use a mouse, set the switch to
0. To use control codes, set the
switch to 1.
* Default
setting
note
For a list of control codes, go
to http://support.epson.com.
After selecting your product
from the list, you can access
technical information on
controlling your document
camera from your computer.
Setting Up the Document Camera 15
elpdc04.book Page 16 Tuesday, February 12, 2002 8:32 AM
16
Setting Up the Document Camera
elpdc04.book Page 17 Tuesday, February 12, 2002 8:32 AM
2
Using the
Document Camera
Once you have set up the document camera, you’re ready to turn it
on, adjust the image, and give your presentation. This chapter covers
the following:
■
Turning on the document camera and other equipment
■
Switching between picture sources
■
Adjusting the lighting
■
Adjusting the image
■
Using the pointer
■
Pausing the Main display
■
Adjusting settings with the on-screen display
■
Using the camera head as a conventional video camera
■
Using the Image Mate software
■
Turning off and storing the document camera
Using the Document Camera 17
elpdc04.book Page 18 Tuesday, February 12, 2002 8:32 AM
Turning On Your Equipment
Make sure your document camera and other equipment are set up and
connected correctly, as described in Chapter 1. Always turn on your
projector or monitor first. Then turn on your document camera, as
described below, followed by any other equipment you’ve connected
to it.
You can turn on your computer and video equipment in any order. If
you have both a computer and video source connected, you may have
to switch to the desired source to see its image, as described on
page 20.
Turning On the Document Camera
Follow these steps to plug in and turn on the document camera:
1. Connect one end of the power cord to the document camera’s
power inlet.
AC IN
POWER
RS-232C
ON
RGB OUT
VIDEO
OUT
RGB IN
USB
0
1
ABC
OFF
power
inlet
2. Connect the other end to a grounded electrical outlet.
3. Turn on the projector or monitor.
4. Turn on the document camera.
AC IN
POWER
ON
RS-232C
RGB OUT
VIDEO
OUT
RGB IN
USB
0
1
OFF
ABC
power switch
After a few moments, the upper lamps turn on.
5. Place your presentation material on the stage. You should see an
image on screen.
18
Using the Document Camera
elpdc04.book Page 19 Tuesday, February 12, 2002 8:32 AM
Once you see your image, turn to page 22 for instructions on making
adjustments.
If your image doesn’t appear, see the next section for help.
When you’re done with your presentation, turn off the document
camera as described on page 27.
note
If you turn off the document
camera, always wait a few
seconds before turning it
back on.
What To Do If You See a Blank Screen
If an image doesn’t appear, try the following:
■
Make sure the cables are connected correctly, as described on
page 11 for a projector or monitor or page 13 for a computer.
■
Make sure everything is turned on.
■
Make sure the lighting unit lamps are on.
■
If you are using a video source, such as a laptop or desktop
computer, you may need to switch video sources. Press the RGB1
button as shown on page 20.
■
If an image still doesn’t appear, refer to Chapter 4 for more help.
Using the Document Camera 19
elpdc04.book Page 20 Tuesday, February 12, 2002 8:32 AM
Switching Between Picture Sources
If you have an external video source connected to the document
camera, such as a laptop or desktop computer, you can switch between
the video source and the camera. Press the RGB1 button on the
remote control to switch the video source. Press the Main button to
switch back to the camera.
Main
20
Using the Document Camera
RGB1
elpdc04.book Page 21 Tuesday, February 12, 2002 8:32 AM
Adjusting the Lighting
If you are presenting printed material or 3-D objects, the two upper
lamps provide ample light. If the ambient lighting in the room is
sufficient, however, you may obtain a better image with the upper
lamps off.
Press the Lamp button on the remote control to turn off the lamps
one at a time from right to left (when facing the unit’s control panel).
Press it a third time to turn the lamps back on. There will be a slight
delay before the lamps turn back on.
Turn upper lamps
off or on
Using the Document Camera 21
elpdc04.book Page 22 Tuesday, February 12, 2002 8:32 AM
Adjusting the Image
Once you see your image, you may need to make certain adjustments:
■
To zoom or focus your image, see the next section.
■
If the image is too light or dark, see page 23.
■
If the image has a color cast, see page 23.
Zooming and Focusing Your Image
Use the Tele button on the control panel or remote control to enlarge
the image, and use the Wide button to reduce it. The document
camera will automatically focus the image.
Your document camera is equipped with a double speed zoom feature.
Press Tele or Wide briefly to zoom at normal speed. Press and hold in
either button to zoom at a higher rate of speed.
note
If you change items on the stage, press the Auto Focus button to
focus the image. The indicator light flashes until the image is focused.
The auto focus function
works up to a height of
approximately 5.9 in.
(15 cm) above the stage
surface.
The following objects may not focus well using the auto focus feature:
Remote Control
■
Objects with little contrast
■
Objects with a bright background or excessive contrast
■
Objects with fine repeated patterns or stripes
■
Objects that glitter or reflect bright light
■
Objects with varying depths of field
To manually focus these objects, use the Near or Far button on the
remote control.
Control Panel
Enlarge
Reduce
Far
Enlarge Reduce Near
22
Auto
Focus
Using the Document Camera
Auto Focus
elpdc04.book Page 23 Tuesday, February 12, 2002 8:32 AM
Adjusting the Brightness
The document camera is initially set to auto iris. You can manually
adjust the iris to control the amount of light that reaches the camera.
If the screen looks dark, press the Open button on the remote control
to open the iris so that more light reaches the camera. If the screen
looks too bright, press the Close button. To return to the auto iris
default setting, press the Auto Iris button.
Remote control
direction
correct
buttons
color cast
Adjusting the White Balance
In different lighting conditions it may be necessary to adjust the
document camera’s white balance. This setting automatically corrects
for color shifts in different lighting environments.
If the displayed image has a color cast, press the AWB button on the
remote control to automatically adjust the white balance. See page 24
for manual white balance adjustments using the document camera’s
on-screen display.
Using the Pointer
The pointer lets you direct attention to specific sections of your
presentation material. You can choose from two types of pointers in
four colors.
increase
brightness
reduce
brightness
To make the pointer appear on the screen, press the Pointer button
on the remote control. When the mouse is connected to the document
camera, pressing the left mouse button will also display the cursor.
To move the pointer, use the direction buttons on the remote control.
The mouse also allows you to move the pointer as you would on a
computer.
To remove the pointer from the screen, press the Pointer button on
the remote control or click the left mouse button three times (this
brings up an on-screen display before the pointer is removed).
For information on selecting different types of pointers, see page 24.
note
The pointer feature only
works when the document
camera is in the Main
display mode. It does not
work then the document
camera is in the RGB1
display mode.
Using the Document Camera 23
elpdc04.book Page 24 Tuesday, February 12, 2002 8:32 AM
Pausing the Main Display
note
The pause feature only works
when the document camera is
in the Main display mode. It
does not work then the
document camera is in the
RGB1 display mode.
During a presentation, it may be necessary to change the material you
are displaying. Press the Pause button before switching your material.
This freezes the image on screen, allowing you to change your
material. When you are ready to display the next item, press the
Pause button again.
Adjusting Settings with the On-Screen
Display
The on-screen display allows access to many of the settings available
with the document camera’s remote control. To access the on-screen
display, you must have the mouse connected to the document
camera’s RS-232C port (See “Connecting a Mouse to the Document
Camera” on page 14). When the left mouse button is clicked, the
on-screen display and the pointer appears. The table below lists the
various functions and their descriptions.
Icon
24
Name
Function
Lighting Unit
On/Off
Turns off the lamps individually. Click once to turn off the right
lamp. Click a second time to turn off the left lamp. Click a third
time to turn on both lamps (this may take a few seconds).
Color/B&W
Switches the display from Color to B&W (black and white).
Pause
On/Off
Switches the screen from Live to Still.
Using the Document Camera
elpdc04.book Page 25 Tuesday, February 12, 2002 8:32 AM
Icon
Name
Function
Auto Focus
Automatically brings objects on the stage into focus.
Zoom
Tele/Wide
Zooms in or out.
Focus
Near/Far
Manually focuses objects that do not work with the auto focus
feature.
Iris
Open/Close
Increases or reduces image brightness.
Pointer
Changes the shape and color of the on-screen pointer.
White balance
Automatic
Automatically adjusts the white balance and corrects color casts.
White balance
Manual
Enables manual white balance adjustment. Click the arrows below
to adjust the colors individually to compensate for color casts.
Aperture
selection
On/Off
Turns image enhancement (contour) on and off. This setting is on
by default.
Gamma
selection
Changes the gamma setting from 1.0 to 0.6. The default gamma
setting is 1.0.
Save settings
Saves change made to the document camera.
Restore
defaults
Restores settings to factory defaults.
Using the Document Camera 25
elpdc04.book Page 26 Tuesday, February 12, 2002 8:32 AM
Using the Camera Head as a
Conventional Video Camera
note
The camera’s shutter operates
at 15 frames per second.
By rotating the camera head to a horizontal position, you can use the
document camera as a conventional video camera. To view walls or
distant objects, flip down the close-up lens. The document camera can
resolve images from 3.6 feet (1.1 m) to infinity.
camera head in
horizontal position
close-up
lens
Using the Image Mate Software
The Image Mate software allows you to transfer images from the
document camera to the PC. You can also use the virtual remote
control feature to control the document camera and change its
settings. For more information on installing and using the Image
Mate software, see the manual.pdf file in the US folder on the Image
Mate CD-ROM. To view the PDF file, you will need to have Adobe®
Acrobat® Reader® installed on your computer. If it’s not already
installed, run ar500enu.exe in the Acrobat US folder on the
CD-ROM.
26
Using the Document Camera
elpdc04.book Page 27 Tuesday, February 12, 2002 8:32 AM
Turning Off and Storing the
Document Camera
When you’ve finished using the document camera, follow these steps
to turn off and store it. If you’re using a monitor or projector, shut it
down last.
1. Turn off the document camera.
2. Unplug the power cord and disconnect any attached video cables.
3. If the close-up lens is flipped down, close it.
4. Place the remote control inside the remote control storage
compartment and close the tray.
remote control
Using the Document Camera 27
elpdc04.book Page 28 Tuesday, February 12, 2002 8:32 AM
caution
5. Turn the lighting units toward the lighting arms until they stop;
then tilt the lighting arms toward the stage (inward).
Be careful not to let the
camera arm drop, or you may
damage it.
lighting unit
lighting arm
lighting unit
lighting arm
stage
6. Rotate the lighting units backward, as shown, until they stop.
28
Using the Document Camera
elpdc04.book Page 29 Tuesday, February 12, 2002 8:32 AM
7. Lower the right lighting arm and rotate the camera head to its
original position.
8. Raise the camera arm until you hear a click, then lower the arm
until it stops.
s
Using the Document Camera 29
elpdc04.book Page 30 Tuesday, February 12, 2002 8:32 AM
30
Using the Document Camera
elpdc04.book Page 31 Tuesday, February 12, 2002 8:32 AM
3
Maintaining and
Transporting the
Document Camera
Y
warning
Before you clean any part of
the document camera, turn it
off and unplug the power
cord. Never open any cover
on the document camera.
Dangerous electrical voltages
in the document camera can
injure you severely. Don’t try
to service this product
yourself. Refer all servicing to
qualified service personnel.
our document camera needs little maintenance. All you need to do
on a regular basis is keep the lenses and stage clean. Any dirt or smears
on the lenses or stage may show up on your presented image.
You should not replace the lamps or any other parts. If any part needs
replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■
Cleaning the lenses
■
Cleaning the document camera case
■
Transporting the document camera
Maintaining and Transporting the Document Camera 31
elpdc04.book Page 32 Tuesday, February 12, 2002 8:32 AM
Cleaning the Lenses
Clean the lenses whenever you notice dirt or dust on the surface.
■
Use a canister of compressed air to remove dust.
■
To remove dirt or smears on the lenses, use lens-cleaning paper. If
necessary, moisten a soft cloth with lens cleaner and gently wipe
the lens surface.
■
Clean both sides of the close-up lens.
main lens
close-up lens
32
Maintaining and Transporting the Document Camera
elpdc04.book Page 33 Tuesday, February 12, 2002 8:32 AM
Cleaning the Document Camera Case
Before you clean the case, first turn off the document camera and
unplug the power cord.
■
To remove dirt or dust, wipe the case with a soft, dry, lint-free
cloth.
■
To remove stubborn dirt or stains, moisten a soft cloth with water
and a neutral detergent. Then wipe the case.
■
Do not use wax, alcohol, benzene, thinner, or other chemical
detergents. These can damage the case.
■
Take special care when cleaning the stage, or you may scratch it.
Scratches on the stage may appear on your image.
stage
Maintaining and Transporting the Document Camera 33
elpdc04.book Page 34 Tuesday, February 12, 2002 8:32 AM
Transporting the Document Camera
note
EPSON shall not be liable
for any damages incurred
during transportation.
The document camera contains many glass and precision parts. If you
need to transport it, follow these guidelines to prevent damage to the
document camera:
■
Make sure to turn off and fold the document camera as described
on page 27.
■
When shipping the document camera for repairs, use the original
packaging material if possible. If you do not have the original
packaging, use equivalent materials, placing plenty of cushioning
around the document camera.
■
When transporting the document camera a long distance, pack it
in a firm box, using cushioning around the document camera.
■
When you are hand-carrying the document camera, be sure to use
the carrying handle.
■
When transporting the document camera, you may leave the
remote control inside the remote control storage compartment.
remote control
storage
compartment
carrying handle
34
Maintaining and Transporting the Document Camera
elpdc04.book Page 35 Tuesday, February 12, 2002 8:32 AM
4
Solving Problems
T
his chapter helps you solve problems with your document camera,
and tells you how to contact technical support for problems you can’t
solve yourself. This chapter explains the following:
■
Solving problems with the image
■
Solving problems with the remote control
■
Contacting technical support
Solving Problems 35
elpdc04.book Page 36 Tuesday, February 12, 2002 8:32 AM
Solving Problems with the Image
No image appears on the screen.
■
Check that all cables are properly connected (see Chapter 1) and
everything is turned on.
■
Make sure the projector or computer is not in sleep mode. Check
the projector documentation, or try pressing a key on the
computer keyboard.
■
The document camera may have been turned on too quickly after
it was turned off. Turn the document camera off, wait a few
seconds, and then turn it on again.
■
The wrong source may be selected. Try pressing the Main or
RGB1 button on the remote control.
■
You may need to change the NTSC or PAL DIP switch setting on
the document camera. See page 15 for instructions.
The image contains static or noise.
■
If you’re using cables that are longer than 6 feet (2 m), or an
extension cable, the image quality may be reduced. Try using the
cables supplied with the document camera.
■
Keep your projector, computer, and video cables away from the
power cord as much as possible to prevent interference.
■
The camera’s DIP switches may be set incorrectly. Try adjusting
the switches as described on page 15.
The image is blurry.
36
Solving Problems
■
There may be dirt on the lenses. Clean the lenses as described on
page 32.
■
Try pressing the Auto Focus button.
■
Some objects do not auto focus well (see page 22). Manually focus
these objects using the Near and Far buttons.
elpdc04.book Page 37 Tuesday, February 12, 2002 8:32 AM
■
The presentation material may be too close to the lens. Make sure
the close-up lens is closed.
■
The presentation material may be too far from the lens. Open the
lens by flipping it down.
■
Make sure there is no condensation on the lenses. You may need
to wait before using the document camera after moving it from a
cold environment to a warm environment.
Solving Problems with the
Remote Control
■
Make sure you are within 23 feet (7 m) of the document camera,
and within range of the document camera’s front or back sensor
(approximately 30° to the left or right and 15° above or below).
■
The remote control batteries may not be installed correctly or may
be low on power. Try changing the batteries as described on
page 7.
■
Dim the room lights and turn off any fluorescent lighting. Make
sure the document camera is not in direct sunlight. Strong
lighting, especially fluorescent lights, may affect the document
camera’s infrared receivers.
■
Turn off any nearby equipment that emits infrared energy, such
as a radiant room heater.
Solving Problems 37
elpdc04.book Page 38 Tuesday, February 12, 2002 8:32 AM
Where to Get Help
EPSON provides technical assistance through electronic support
services 24 hours a day, as listed in the following table:
Service
Access
World Wide Web
From the internet, you can reach EPSON’s product support at
http://support.epson.com. After selecting your product, you can access
troubleshooting information, download product documentation, and receive
technical advice through e-mail.
Presenters Online
Access tips, templates, and training for developing successful presentations at
http://www.presentersonline.com.
Telephone Support Services
To use the EPSON PrivateLine Support service, call (800) 637-7661
and enter the PIN on the EPSON PrivateLine Support card included
with your document camera. This is the fastest way of speaking to a
live representative, and it’s free. This service is available 6 AM to 6 PM,
Pacific Time, Monday through Friday, for the duration of your
warranty period.
You may also speak with an EPSON document camera support
specialist by dialing one of these numbers:
■
U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday
through Friday
■
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday
through Friday
Toll or long distance charges may apply.
Before you call, please have the following information ready:
38
Solving Problems
■
Product name (EPSON ELPDC04 High Resolution Document
Camera)
■
Product serial number (located on the rear panel of the document
camera)
■
Computer configuration, if applicable
■
Description of the problem
elpdc04.book Page 39 Tuesday, February 12, 2002 8:32 AM
5
Technical Specifications
General
CCD
1/3 inch (848,676 progressive square pixels)
Resolution
1024 × 768 pixels
Lens
F=2.8, f=5.8 to 58 mm
Frame speed
15 frames per second
Shooting area
13.4 × 9.9 in. (340 × 252 mm) max.
1.5 × 1.1 in. (38 × 28 mm) min.
Limit of focus
adjustment
5.9 in. (150 mm) from the stage surface
using the close-up lens
1.6 feet (.5 m) to infinity with the camera
positioned horizontally and without using
the close-up lens
Zoom
10× optical with double speed function
Focus
Automatic/manual
Iris
Automatic/manual
White balance
Automatic/manual
Gamma selection
ON (γ=0.6), OFF (γ=1.0)
Frequency selection
50 or 60 Hz
Video output
NTSC or PAL
Lighting
Lamps
High frequency fluorescent, 9 W × 2
Technical Specifications 39
elpdc04.book Page 40 Tuesday, February 12, 2002 8:32 AM
Remote Control
Range
23 feet (7 m)
Batteries
Alkaline AAA (2)
Dimensions
Weight
14.3 lb (6.5 kg)
Folded (h × w × d)
3.9 × 19.7 × 24.1 in.
(99 × 500 × 612 mm)
Unfolded (h × w × d)
22.6 × 27.8 × 15.9 in.
(575 × 706 × 403 mm)
Electrical
Rated frequency
50/60 Hz
Power supply
100 to 120 VAC
Power consumption
100 to 120 VAC: 55 W
Environmental
Temperature
Operating: 41 to 104 °F (5 to 40 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Humidity
Operating: 30 to 85% RH,
non-condensing
Storage: 20 to 90% RH,
non-condensing
40
Technical Specifications
elpdc04.book Page 41 Tuesday, February 12, 2002 8:32 AM
Safety
United States
FCC 47CFR Part 15B Class B (DoC)
UL1950 3rd Edition
Canada
ICES-003
CSA C22.2 No.950-95 (cUL)
Compatible Video Formats
The document camera supports NTSC and PAL video standards, as
well as the monitor display formats listed below.
Mode
Refresh Rate (Hz)
Resolution
VGA1
85.08
640 × 350
VGA2
85.08
640 × 400
VGA3
85.039
720 × 400
VGA—60
59.94
640 × 480
VGA—72
72.809
640 × 480
VGA—75
75
640 × 480
VGA—85
85.008
640 × 480
SVGA—56
56.25
800 × 600
SVGA—60
60.317
800 × 600
SVGA—72
72.188
800 × 600
SVGA—75
75
800 × 600
SVGA—85
85.061
800 × 600
XGA—60
60.004
1024 × 768
XGA—70
70.069
1024 × 768
XGA—75
75.029
1024 × 768
XGA—85
84.997
1024 × 768
SXGA1
75
1152 × 864
SXGA2
60
1280 × 960
SXGA3
85.002
1280 × 960
SXGA—60
60.02
1280 × 1024
Technical Specifications 41
elpdc04.book Page 42 Tuesday, February 12, 2002 8:32 AM
42
Technical Specifications
Mode
Refresh Rate (Hz)
Resolution
SXGA—75
75.025
1280 × 1024
SXGA—85
85.024
1280 × 1024
UXGA—60
60
1600 × 1200
UXGA—65
65
1600 × 1200
UXGA—70
70
1600 × 1200
UXGA—75
75
1600 × 1200
UXGA—85
85
1600 × 1200
MAC 13
66.667
640 × 480
MAC 16
74.55
832 × 624
MAC 19
74.927
1024 × 768
MAC 21
75.062
1152 × 870
PC98
56.42
640 × 400
elpdc04.book Page 43 Tuesday, February 12, 2002 8:32 AM
6
Notices
This chapter includes safety instructions and other important information
about your EPSON document camera.
Important Safety Instructions
Follow these safety instructions when setting up and using the document
camera:
■
■
■
■
■
■
■
■
Read Instructions – All the safety and operating instructions should be
read before the appliance is operated.
Retain Instructions – The safety and operating instructions should be
retained for future reference.
Heed Warnings – All warnings on the product appliance and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions should be
followed.
Cleaning – Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
Attachments – Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water—for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, and the like.
Accessories – Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or
sold with the product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
Notices 43
elpdc04.book Page 44 Tuesday, February 12, 2002 8:32 AM
■
■
Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect
it from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer’s instructions have been adhered to.
Place the document camera near a wall outlet where the plug can be
easily unplugged.
Placez l’appareil près d’une prise de courant où la fiche peut être débranchée
facilement.
■
■
■
■
■
44
Notices
Power Sources – This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your appliance dealer or
local power company. For products intended to operate from battery
power or other sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped with either
a polarized 2-wire AC line plug (a plug having one blade wider than the
other) or a 3-wire grounding type plug (a plug having a third grounding
pin). The 2-wire polarized plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug still fails to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug. The 3-wire grounding type plug will fit
into a grounding type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the
grounding type plug.
Power-Cord Protection – Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
Lightning – For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
Overloading – Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric
shock.
elpdc04.book Page 45 Tuesday, February 12, 2002 8:32 AM
■
■
■
■
■
■
■
A product and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the product and
cart combination to overturn.
Object and Liquid Entry – Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
Servicing – Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
Damage Requiring Service – Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
■
When the power-supply cord or plug is damaged.
■
If liquid has been spilled, or objects have fallen into the product.
■
If the product has been exposed to rain or water.
■
If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the product to its normal operation.
■
If the product has been dropped or damaged in any way.
■
When the product exhibits a distinct change in performance—this
indicates a need for service.
Replacement Parts – When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other
hazards.
Safety Check – Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
Heat – The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat.
Notices 45
elpdc04.book Page 46 Tuesday, February 12, 2002 8:32 AM
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
THIS IS A CLASS B PRODUCT. IN A DOMESTIC
ENVIRONMENT THIS PRODUCT MAY CAUSE
RADIO INTERFERENCE IN WHICH CASE THE USER
MAY BE REQUIRED TO TAKE ADEQUATE
MEASURES.
Remote Control Information
You can operate the document camera by remote control via a line-of-sight
infrared (IR) receiver at the front and rear of the document camera. The
document camera may not respond to remote control commands under the
following conditions:
■
■
■
■
■
There is an object between the remote control IR emitter and the IR
receiver on the document camera.
Ambient light is too bright.
Certain types of fluorescent lighting are used.
A strong light source shines into the IR receiver.
Other equipment that emits infrared energy, such as a radiant room
heater, is in the room.
These conditions commonly cause problems for most infrared-controlled
equipment. Try the following:
■
■
■
■
The remote control batteries may be low on power; replace them.
Dim the ambient lighting and/or turn off any fluorescent lights.
Close any window coverings and/or move the document camera out of
direct sunlight.
Turn off other equipment that emits infrared energy.
If the remote control still does not work properly, you can always use the
buttons located on the document camera control panel, even in an
environment containing one of the conditions listed above.
46
Notices
elpdc04.book Page 47 Tuesday, February 12, 2002 8:32 AM
Declaration of Conformity
According to 47CFR, Part 2 and 15 Class B Personal Computers and
Peripherals; and/or CPU Boards and Power Supplies used with Class B
Personal Computers
We:
Located at:
EPSON AMERICA, INC.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806-2469
Telephone:
(562) 290-5254
Declare under sole responsibility that the product identified herein, complies
with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each
product marketed, is identical to the representative unit tested and found to
be compliant with the standards. Records maintained continue to reflect the
equipment being produced can be expected to be within the variation
accepted, due to quantity production and testing on a statistical basis as
required by 47CFR §2.909. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Trade Name:
EPSON
Type of Product: Image Presentation Camera
Model:
ELPDC04
Notices 47
elpdc04.book Page 48 Tuesday, February 12, 2002 8:32 AM
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
■
■
■
■
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification of this device and may cause
interference levels which exceed the limits established by the FCC for this
equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than
one interface connector, do not leave cables connected to unused interfaces.
Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
For Canadian Users
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le materiel brouilleur du Canada.
48
Notices
elpdc04.book Page 49 Tuesday, February 12, 2002 8:32 AM
Warranty
Epson America, Inc. Limited Warranty
What Is Covered: Epson America, Inc. (“Epson”) warrants to the first end user
customer of the EPSON product enclosed with this limited warranty
statement that the product, if purchased and used in the United States or
Canada, conforms to the manufacturer’s specifications and will be free from
defects in workmanship and materials for a period of two (2) years from the
date of original purchase (except that the warranty period is 90 days for
lamps). For warranty service, you must provide proof of the date of original
purchase.
What Epson Will Do To Correct Problems: Should your EPSON product
prove defective during the warranty period, please bring the product securely
packaged in its original container or an equivalent, along with proof of the
date of original purchase, to your EPSON Dealer or EPSON Customer Care
Center. Epson will, at its option, repair or replace on an exchange basis the
defective unit, without charge for parts or labor. When warranty service
involves the exchange of the product or of a part, the item replaced becomes
EPSON property. The exchanged product or part may be new or previously
repaired to the EPSON standard of quality. Exchange or replacement
products or parts assume the remaining warranty period of the product
covered by this limited warranty. However, each replacement lamp carries
the limited 90-day warranty stated above.
What This Warranty Does Not Cover: This warranty covers only normal use in
the United States and Canada. For lamps, 24-hour-per-day use causes
unusual strain and is not considered normal use. This warranty is not
transferable and will not apply to products purchased from an end user. This
warranty does not cover consumables (e.g., fuses), other than lamps. EPSON
is not responsible for warranty service should the EPSON label or logo or the
rating label or serial number be removed or should the product fail to be
properly maintained or fail to function properly as a result of misuse, abuse,
improper installation, neglect, improper shipping, damage caused by disasters
such as fire, flood, and lightning, improper electrical current, software
problems, interaction with non-EPSON products, or service other than by an
EPSON Authorized Servicer. Postage, insurance, or shipping costs incurred
in presenting your EPSON product for carry-in warranty service are your
responsibility. If a claimed defect cannot be identified or reproduced in
service, you will be held responsible for costs incurred.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED
WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
Notices 49
elpdc04.book Page 50 Tuesday, February 12, 2002 8:32 AM
FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW
THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS
APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE
LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE.
UNLESS STATED HEREIN, ANY STATEMENTS OR
REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM
ARE VOID. EXCEPT AS PROVIDED IN THIS WRITTEN
WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS
AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE,
OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR
INABILITY TO USE THE EPSON PRODUCT, WHETHER
RESULTING FROM BREACH OF WARRANTY OR ANY OTHER
LEGAL THEORY. IF THE REMEDY ABOVE FAILS, EPSON’S
ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE
PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS
LIMITED WARRANTY.
In Canada, warranties include both warranties and conditions.
Some jurisdictions do not allow limitations on how long an implied warranty
lasts and some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions
may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights which vary from jurisdiction to jurisdiction.
To locate an Authorized EPSON Servicer nearest you, call the EPSON
SM
Connection at (562) 276-4394 in the U.S. and (905) 709-3839 in Canada
or write to: Epson America, Inc., P. O. Box 93012, MS: 6-33, Long Beach,
CA 90809-3012.
50
Notices
elpdc04.book Page 51 Tuesday, February 12, 2002 8:32 AM
Index
Numerics
D
3-D objects, presenting, 21
Declaration of Conformity, 47
DIP switches, adjusting, 15
Document camera
cleaning, 31 to 33
connecting, 11 to 14
folding, 27 to 29
positioning, 8
specifications, 39 to 42
storing, 27 to 29
transporting, 34
turning off, 27
turning on, 18 to 19
unfolding, 9 to 10
A
Adjusting settings, 24 to 25
Auto Focus button, 22
Auto Iris button, 23
B
Batteries, installing, 7
Blank screen, 19
Blurry image, 36 to 37
Brightness, adjusting, 23
Buttons
focus, 22
iris, 23
lamp, 21
main, 20
pause, 24
RGB1, 20
zoom, 22
C
Cables, 6, 36
Cleaning, 31 to 33
Close button, 23
Close-up lens, 26, 32
Computer, connecting to, 13
Connecting document camera
to a computer, 13
to a monitor, 11 to 12
to a mouse, 14
to a projector, 11 to 12
Control codes, 15
E
Electrical specifications, 40
Enlarging, image, 22
Environmental specifications, 40
EPSON technical support, 3, 38
F
Far button, 22
FCC compliance statement, 48
Focusing image, 22
Folding document camera, 27 to 29
Frame speed, 26, 39
G
Gamma, 39
H
Help, 3, 38
Index 51
elpdc04.book Page 52 Tuesday, February 12, 2002 8:32 AM
I
Image
brightness, 23
focusing, 22
resolution, 39
shooting area, 39
shooting speed, 26, 39
sources, selecting, 20
troubleshooting, 19, 36 to 37
white balance, 23, 25
zooming, 22
Image Mate Software, 26
Iris, adjusting, 23
L
Lamp
selecting, 21
specifications, 39
Lens
cleaning, 31 to 32
specifications, 39
Lighting, adjusting, 21
M
Main button, 20
Monitor, connecting, 11 to 12
Mouse, connecting, 14
N
Near button, 22
O
On-screen display, adjusting settings, 24 to 25
Open button, 23
P
Picture, see Image
Pointer, using, 23
Positioning, document camera, 8
Power
specifications, 40
switch, 18
52
Index
PrivateLine Support, 3, 38
Problems
blank screen, 19
image, 36 to 37
remote control, 37, 46
Projector, connecting, 11 to 12
R
Reducing, image, 22
Registration, 3
Remote control
batteries, 7
specifications, 40
storing, 34
troubleshooting, 37, 46
Resolution, 39
RGB1 button, 20
S
Safety
instructions, 43 to 45
specifications, 41
Screen image, see Image
Service, see Technical support
Shooting speed, 26, 39
Software, 26
Specifications
dimensions, 40
electrical, 40
environmental, 40
general, 39
lamp, 39
lens, 39
remote control, 40
safety, 41
video formats, 41 to 42
Support, see Technical support
T
Technical support, 3, 38
Tele button, 22
Television, connecting, 11 to 12
Temperature requirements, 40
elpdc04.book Page 53 Tuesday, February 12, 2002 8:32 AM
Transporting, 34
Troubleshooting
image, 19, 36 to 37
remote control, 37, 46
Turning off document camera, 27
Turning on document camera, 18 to 19
U
Unfolding, document camera, 9 to 10
Unpacking, document camera, 6
V
Video camera, using camera as, 26
Video formats supported, 41 to 42
W
Warranty, 49 to 50
White balance, adjusting, 23, 25
Wide button, 22
Z
Zooming image, 22
Index 53