Zanussi ZGF 642 Technical data

GAS HOB
MODEL ZGF 642
INSTRUCTION BOOKLET
2
Please read this instruction booklet before using the appliance
Important Safety Information
You MUST read hese warnings carefully before installing or using the hob.
If you need assistance, contact our Customer Care Department
on 01635 521313
Installation
●
This hob must be installed by qualified personnel,
according to the manufacturer’s instructions and to
the relevant British Standards.
●
Any gas installation must be carried out by a
registered CORGI installer.
●
Remove all packaging before using the hob.
●
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near
the gas supply pipe.
●
●
When using other electrical appliances, ensure the
cable does not come into contact with the hot
surfaces of the cooking appliance.
●
Unstable or misshapen pans should not be used on
the hob as unstable pans can cause an accident by
tipping or spillage.
●
Never leave the hob unattended when cooking with
oil and fats.
●
Never use plastic or aluminium foil dishes on the
hob.
●
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above or
below the hob unit.
Do not attempt to modify the hob in any way.
Child Safety
●
This hob is designed to be operated by adults. Do
not allow children to play near or with the hob.
●
The hob gets hot when it is in use.
●
Children should be kept away until it has cooled.
●
Children can also injure themselves by pulling pans
or pots off the hob.
During Use
Service
●
This hob should only be repaired or serviced by an
authorised Service Engineer and only genuine
approved spare parts should be used.
Environmental Information
●
This hob is intended for domestic cooking only. It is
not designed for commercial or industrial purposes.
●
After installation, please dispose of the packaging
with due regard to safety and the environment.
●
When in use a gas cooking appliance will produce
heat and moisture in the room in which it has been
installed. Ensure there is a continuous air supply,
keeping air vents in good condition or installing a
cooker hood with a venting hose.
●
When disposing of an old appliance, make it
unusable, by cutting off the cable.
●
When using the hob for a long period time, the
ventilation should be improved, by opening a
window or increasing the extractor speed.
●
Do not use this hob if it is in contact with water.
Do not operate the hob with wet hands.
●
Ensure the control knobs are in the ‘OFF’ position
when not in use.
Keep this instruction book for future
reference and ensure it is passed on
to any new owner.
3
Contents
For the User
For the Installer
Description
of the Hob
Technical Data
Page 10
Page
5
Operation
Page
6
Important Safety
Requirements
Page 11
Installation
Page 12
Gas Connection
Page 12
Building In
Page 13
Electrical Connection
Page 14
Wiring Diagram
Page 15
Fault Finding
Page 16
Commissioning
Page 18
Servicing
Page 19
Conversion from
natural gas to LPG
Page 19
Maintenance
and Cleaning
Page
7
Something
Not Working
Page
8
Service and
Spare Parts
Page
8
Peace of Mind
for 24 Months
Page
9
Guide to Use the instructions
The following symbols will be found in the text to
guide you throughout the Instructions:
Safety Instructions
☞
i
4
Step by step instructions for an
operation
Hints and Tips
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683
(Low VoltageDirective);
* 93/68 (General Directives);
* 89/336 (Electromagnetical
Compatibility Directive);
* 90/396 (Gas Appliances),
and subsequent modifications
Description of the Hob
2
3
3
1
5
1.
2.
3.
4.
5.
6.
7.
8.
6
7
8
4
Hob Top
Auxiliary Burner
Semi-rapid Burners
Rapid Burner
Control knob for front left burner (auxiliary)
Control knob for back left buner (semi-rapid)
Control knob for back right burner (semi-rapid)
Control knob for front right burner (rapid)
INSTALLATION
Any gas installation must be carried out by
a registered CORGI installer, and in
accordance with existing rules and
regulations.
The relevant instructions are to be found in the
second section of this manual.
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is
important to remove any protective
materials, which were put on in the factory.
Please, ensure that, once the hob is
installed, it is easily accessible for the
engineer in the event of a breakdown.
5
Operation
HOB BURNERS
To light a burner, turn the relevant knob
anticlockwise to maximum position and push down
the knob to ignite.
If the burner does not ignite, turn the control knob to
zero, and try again.
i
When switching on the mains, after
installation or a power cut, it is quite normal
for the spark generator to be activated
automatically.
To ensure maximum burner efficiency, you should
only use pots and pans with a flat bottom fitting the
size of the burner used (see table).
Burner
Large (rapid)
Medium (semi-rapid)
Small (Auxiliary)
minimum
diameter
160 mm.
120 mm.
80 mm.
maximum
diameter
240 mm.
220 mm.
160 mm.
If you use a saucepan which is smaller than
the recommended size, the flame will spread
beyond the bottom of the vessel, causing the
handle to overheat.
i
As soon as a liquid starts boiling, turn down
the flame so that it will barely keep the
liquid simmering.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
If the control knobs become difficult to turn,
please contact your local Electrolux Service
Centre.
6
Maintenance and Cleaning
Before any maintenance or cleaning can be
carried out, you must DISCONNECT the
hob from the electricity supply.
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is left
to cool.
The Hob Top
Regularly wipe over the hob top using a soft cloth
well wrung out in warm water to which a little
wasing up liquid has been added. Avoid the use of the
following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob
Brite or Bar Keepers Friend is used.
Pan Supports
YES
The hob has two cast iron pan supports.
Take care when removing them. They are fair heavy
and could damage the hob or your kitchen furniture if
you let them fall down.
To keep the pan supports in the correct position, they
are hooked into hinges at the back of the hob. When
removing the pan supports, lift them up as shown in
the diagram. Never turn the pan supports on the
hinges, this could damage them.
Wash the pan supports using hot soapy water. If
necessary, a paste cleaner or a soap impregnated steel
wool pad can be used with caution.
The Burners
NO
The burner caps and crowns can be removed for
cleaning.
Wash the burners taps and crowns using hot soapy
water, and remove marks with a mild paste cleaner. A
well moistened soap impregnated steel wool pad can
be used with caution, if the marks are particularly
difficult to remove.
After cleaning, be sure to wipe dry with a soft cloth.
7
Something Not Working?
If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi
Service Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
SYMPTOM
■ There is no spark when lighting the gas
SOLUTION
◆ Check that the unit is plugged in and the electrical
supply is switched on
◆ Check that the RCCB has not tripped (if fitted)
◆ Check the mains fuse has not blown
◆ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
■ The gas ring burns unevenly
◆ Check the main jet is not blocked and the burner
crown is clear of food particles.
◆ Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
If after all these checks, the oven still does not work,
contact your local Zanussi Service Force Centre.
When you contact them, they will need the following
information:
1. Your name, address and post code.
2. Your telephone number
3. Clear and concise details of the fault
4. The model and the serial number (which can be
found on the rating plate)
5. Date of purchase
8
Please note that it will be necessary to provide proof
of purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.
Service and Spare Parts
If you require spare parts or an engineer contact your
local Service Force Centre by telephoning:
0870 5 929929
Your call will be routed to your local Service Force
Centre. For further details, please see the
accompanying Customer Care Booklet.
CUSTOMER CARE
For general enquiries concerning your Zanussi
appliance, contact our Customer Care Department by
letter or telephone as follows:
Customer Care Department
ZANUSSI
Zanussi House
Hambridge Road
Newbury, Berks, RG14 5EP
Tel: 01635 - 521313
Peace of Mind for 24 Months
ZANUSSI GUARANTEE CONDITIONS
We, Zanussi, undertake that if, within 24 months of
the date of the purchase, this Zanussi appliance or
any part thereof is proved to be defective by any
reason only of faulty workmanship or materials, we
will, at our option, repair or replace the same FREE
OF ANY CHARGE for labour, materials or carriage
on condition that:
* The appliance has been correctly installed and
used only on the gas and electricity supply stated
on the rating plate.
* The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
* All service work under this guarantee must be
undertaken by a Zanussi Service Centre.
* Any appliance or defective part replaced shall
become the Company's property.
* This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours, in which case a premium will be
charged.
Exclusions
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
* Appliances found to be in use within a
commercial or similar environment, plus those
which are the subject to rental agreements.
* Products of Zanussi manufacture which are not
marketed by Zanussi.
European Guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new
home subject to the following qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the
same extent for labour and parts as exist in the
new country of use for this brand or range of
products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European
Community (EC) or European Free Trade Area.
* The product is installed and used in accordance
with our instructions and is only used
domestically, i.e. a normal household
* The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest
Customer Care centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your move
and able to look after you and your appliances.
France
Senlis
+33 (0)3 44 62 29 99
Germany Nürnberg +49 (0)911 323 2600
Italy
Pordenone +39 (0)1678 47053
Sweden
Stockholm +46 (0)8 738 79 50
UK
Newbury +44 (0)1635 521 313
9
Instructions for the Installer
Engineer technical data
OVERALL DIMENSIONS
Width:
Depth:
Height:
Weight:
SUPPLY CONNECTIONS
Gas:
RC 1/2 inch (1/2 inch male) Rear right hand corner
580 mm.
510 mm.
72 mm.
12 Kg.
Electric:
230-240V 50Hz supply, 3 core flexible cable with
non rewireable plug fitted with a 3 amp cartridge
fuse.
CUT OUT DIMENSIONS
Width:
560 mm.
Depth:
480 mm.
Thickness: 30 mm.
Ignition HT Spark
Spark Generator Ispra Control's BF 50046-06 , 220-240V 0.6 VA T 120
Spark Gap
Fixed
CHARACTERISTICS
VALUE = 37.78 MJ/m3
Ws - 50.7 MJ/ m3
VALUE = 49.92 MJ/Kg
Front Right Burner (rapid)
Heat Input 3.0 kW (10236 BTU/HR)
TYPE OF
GAS
Front Left Burner (auxiliary)
Heat Input 1.0 kW (3412 BTU/HR)
NATURAL GAS
20 mbar
Rear Right Burner (semi rapid)
Heat Input 2.0 kW (6824 BTU/HR)
LPG GAS
28-30/37 mbar
Rear Left Burner (semi rapid)
Heat Input 2.0 kW (6824 BTU/HR)
Burner
Auxiliary
Semi-rapid
Rapid
BURNER
POSITION
SEMI-RAPID
(medium)
AUXILIARY
(small)
MAX
MIN
MAX
MIN
MAX
MIN
NOMINAL THERMAL
POWER
kW
3.0
0.65
2.0
0.45
1.0
0.33
NOMINAL FLOW
RATE
m3/h
0.286
0.062
0.190
0.043
0.095
0.031
119
Adjust.
96
Adjust.
70
Adjust.
2.8
0.65
2.0
0.45
1.0
0.33
202
47
144
32
72
24
86
40
71
32
50
28
NOZZLE REFERENCE
1/100 mm
NOMINAL THERMAL
POWER
kW
NOMINAL FLOW
RATE
g/h
NOZZLE REFERENCE
1/100 mm
Dia. Tap By-pass
1/100 mm
28
32
40
Aeration adjustment none
10
RAPID
(large)
Tap colour
Blue/Blue
Black/Black
Brown/Brown
APPLIANCE CLASS : 3
APPLIANCE
CATEGORY: II2H3+
APPLIANCE
GAS SUPPLY: Natural gas G20 / 20mbar
Important safety requirements
This hob must be installed in accordance with the Gas
Safety (Installation and Use) Regulations (Current
Edition) and the IEE Wiring Regulations (Current
Edition).
Detailed recommendations are contained in the
following British Standards Codes Of Practice: B.S.
6172/ B.S. 5440, Par. 2 and B.S. 6891 Current
Editions.
The hob should not be installed in a bed sitting room
with a volume of less than 20 m3. If it is installed in a
room of volume less than 5 m3 an air vent of effective
area of 110 cm2 is required. If it is installed in a room
of volume between 5 m3 and 10 m3 an air vent of
effective area of 50 cm2 is required, while if the
volume exceeds 11 m3 no air is required.
However, if the room has a door which opens directly
to the outside no air vent is required even if the
volume is between 5 m3 and 11 m3.
If there are other fuel burning appliances in the same
room, B.S. 5440 Part 2 Current Edition, should be
consulted to determine the requisite air vent
requirements.
Location
The hob may be located in a kitchen, a kitchen/diner
or bed sitting room, but not in a bathroom or shower
room.
Before making the cut out in the worktop ensure that
there is a minimum distance of 55 mm. between the
rear edge of the hob and the wall.
A minimum distance of 100 mm. must be left
between the side edges of the hob and any adjacent
cabinets or walls.
The minimum distance combustible material can be
fitted above the hob in line with the edges of the hob
is 420 mm. If it is fitted below 420 mm. a space of 50
mm. must be allowed from the edges of the hob.
The minimum distance combustible material can be
fitted directly above the hob is 700 mm.
ICLEARANCES REQUIRED
CLEARANCES REQUIRED
WHEN FITTING THE HOB
WITH A COOKER HOOD ABOVE
WHEN FITTING THE HOB
WITHOUT A COOKER HOOD ABOVE
600 mm
700 mm
700 mm
650
420 mm
50 m
55
420 mm
mm
m
100
420 mm
mm
mm
m
100
50 m
55
50 m
420 mm
mm
m
50 m
m
FO 0812
FO 0813
11
Installation
IMPORTANT
This hob must be installed by qualified
personnel to the relevant British Standards.
Any gas installation must be carried out by
a registered CORGI installer.
The manufacturer will not accept liability,
should the above instructions or any of the
other safety instructions incorporated in this
book be ignored.
On the end of the shaft, which includes the GJ 1/2"
threaded elbow, adjustment is fixed so that the washer
is fitted between the components as shown in the
diagram. Screw the parts together without using
excessive force.
FO 0814
Gas Connection
Connection to the gas supply should be with either
rigid or semi-rigid pipe, i.e. steel or copper.
The connection should be suitable for connecting to
RC 1/2 (1/2 BSP male thread).
When the final connection has been made, it is
essential that a thorough leak test is carried out on the
hob and installation.
Ensure that the main connection pipe does not exert
any strain on the hob.
FO 0264
A) End of shaft with nut
B) Washer
C) Elbow
It is important to install the elbow correctly,
with the shoulder on the end of the thread,
fitted to the hob connecting pipe.
Failure to ensure the correct assembly will
cause leakage of gas.
Rectangular cut-out size for hob
55 m
in.
Cut Out Size
480
The dimensions of the cut-out are given in the
diagram.
560
Dimensions are given in mm.
FO 2038
12
150
100 min
Building In
Building over a cupboard or drawer
ON/OFF SWITCH
2
ON/OFF SWITCH
3
30
1
It is also recommended to carry out the electrical
connection to the hob as shown in diagrams 1 and 2.
20 min
If the hob is to be installed above a cupboard or
drawer it will be necessary to fit a heat resistant board
below the base of the hob on the underside of the
work surface.
a
60
FLEX
OUTLET
b
FLEX
OUTLET
FO 0763
FO 0764
FO 1013
Dimensions are given in mm.
Building over a kitchen unit with door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in
diagram 3.
The panel fitted under the hob ("a") should be easily
removable to allow easy access if technical assistance
is needed. The space behind the kitchen unit ("b") can
be used for connections.
Fitting the Hob into the worktop
Carry out the building in of the hob as follows:
• put the seals supplied with the hob on the
edges of the cut out, as shown in the diagram,
taking care that the seals meet without
overlapping;
• place the hob in the cut out, taking care that it
is centred;
• fix the hob with the relevant fixing clamps
and screws, as shown in the diagram. When
the screws have been tightened, the excess
seal can be removed.
☞
FO 2239
a
Seal
The edge of the hob forms a double seal which
prevents the ingress of liquids.
FO 0199
13
Electrical connections
Any electrical work required to install this
hob should be carried out by a qualified
electrician or competent person, in
accordance with the current regulations.
THIS HOB MUST BE EARTHED.
The manufacturer declines any liability
should these safety measures not be
observed.
Permanent Connection
In the case of a permanent connection, it is necessary
that you install a double pole switch between the hob
and the electricity supply (mains), with a minimum
gap of 3 mm. between the switch contacts and of a
type suitable for the required load in compliance with
the current electric regulations.
The switch must not break the yellow and green earth
cable at any point.
Ensure that the hob supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
This hob is designed to be connected to a
240V 50Hz AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this
book.
The hob is supplied with a 3 core flexible supply cord
incorporating a 3amp plug fitted. In the event of
having to change the fuse, a 3amp ASTA approved
(BS 1362) fuse must be used.
Should the plug need to be replaced for any reason,
the wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow - Earth
Blue
- Neutral
Brown
- Live
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
or
the letter 'E' or the earth symbol
coloured green and yellow.
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal
in the plug which is marked with the letter 'L'
or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
☞
A cut off plug inserted into a 13 amp
socket is a seriuos safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
14
FO 0390
Wiring Diagram
N
220
240
1
2
3
0
4
2
1
L
1. TAPS IGNITOR SWITCHES
2. IGNITOR UNIT
15
Fault Finding
PLUG (with cover removed)
Earth Wire
Green/Yellow
Brown
Blue
Green
Yellow
START
Isolate appliance
and carry out:
A: Earth Continuity
check.
Neutral Wire
Blue
SOCKET
(face view)
( )
E( )
FUSE
Preliminary Electrical Systems Check
N
L
Blue
Brown
Green
Yellow
NO
YES
Carry out:
C: Polarity check.
Has inlet fuse blown?
NO
YES
Carry out:
D: Resistance to
Earth check.
Electricity supply
should now be
satisfactory.
A. EARTH CONTINUITY CHECK Appliance must be electrically
disconnected - meter set on Ω (Ohms) x 1
scale and adjust zero if necessary.
a) Test leads from any appliance earth point
to earth pin on plug. Resistance should
be less than 0.1 Ω (Ohm), check all earth
wires for continuity and all contacts clean
and tight.
Inlet wiring
faulty.
Rectify any
fault.
B. INSULATION CHECK - Appliance
electrically disconnected, all switches ON.
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
a) meter set on Ω (Ohms) x 1 scale.
Test leads from L to N in appliance
terminal block. If meter reads «0» then
there is a short circuit.
b) meter set on Ω (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter
reads less than ∞ (infinity) there is a fault.
NOTE - Should it be found that the fuse
has failed but no fault is indicated - a
detailed continuity check (i.e. by
disconnecting and checking each
component) is required to trace the faulty
component.
It is possible that a fault could occur as a
result of local burning/arcing but no fault
could be found under test. However a
detailed visual inspection should reveal
evidence of burning around the fault.
16
Ignition System / Gas Ignition
Ignitor does not spark
YES
Check gas supply at
burner
NO
Check plug top fuse and
replace if necessary
Light burner manually
Check polarity and earth
continuity of supply point
Check by pass simmer
adjusted
Check position of the
electrode
Check earth continuity
of appliance
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check continuity from the tip of
each electrode to the terminals 1
to 4 on the ignitor unit
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check for breaks in the insulation
of the HT leads
Check continuity from ignition
switches connector to ignitor unit
Check fitting of burners
Change the taps ignition
switches
Change the ignitor unit
17
Commissioning
When the hob has been fully installed it will be
necessary to check the minimum flame setting. To do
this, follow the procedure below.
- Turn the gas tap to the MAX position and ignite.
- Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times.
If the flame is unstable or is extinguished follow the
procedure below.
Procedure:
☞
Re-ignite the burner and set to MIN.
Remove the control knob and use a thin
bladed screwdriver to turn the adjustment
screw until the flame is steady and does not
extinguish, when the knob is turned from
MIN to MAX.
The adjustment screw may be located at the
centre of the gas tap control shaft or on the
gas tap body, left of the control shaft or
below (see diagram).
Repeat the adjustment procedure for all
burners.
Pressure Testing
☞
Remove left hand pan support and front left
burner cap and crown.
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite
another burner.
The pressure reading should be nominally
20mbar and must be between 17 mbar and
25mbar.
Turn off the burner supplies.
18
Adjustment
screw
Servicing
Repais may only be carried out by
CORGI registered engineers.
A: Removal Of Hob Top
1. Remove all control knobs, pan supports, burner caps
and burner crowns.
2. Remove 2 screws for each burner.
3. Remove 4 fixing screws from the pan support hinges,
and remove the hinges from the hob.
4. Lift hob top at the rear and remove it from the hob.
B: Removal Of the Hob Taps
(Isolate Electrical Supply)
1. Follow the procedures in Section A.
2. Loosen the pipe connection nut from the gas tap with
the aid of a 16mm spanner.
3. From the underside of the hob remove 2 self tapping
screws from the tap.
4. Reassemble in reverse order and carry out leak test.
D: Removal Of Burner
1. Follow the procedures in Section A.
2. With the aid a 12mm spanner loosen off the pipe
connection nut.
3. From the underside of the hob remove 1 self tapping
screw from the burner body.
4. Reassemble in reverse order and carry out leak test.
E: Removal of Ignitor
(Isolate Electrical Supply)
1. Follow the procedures in Section A.
2. Remove H.T. leads from the ignitor by pulling tab
connection off. Disconnect supply cable from the
ignitor unit.
3. With the aid of a pair of thin nose pliers, pull the
spring clip sideward off of the underside of the
ignitor
4. Reassemble in reverse order.
C: Removal Of Mains Terminal Block
(Isolate Electric Supply)
F: Removal of Ignitor Switch
(Isolate Electric Supply)
1. Follow the procedures in Section A.
2. Disconnect supply flex connections from terminal
block.
3. From the underside of the hob remove 1 self tapping
screw from the terminal block.
4. Reassemble in reverse order.
1. Follow the procedures in Section A.
2. Disconnect the switches connector from the ignitor
unit and remove the supply cables pulling the tabs
connection off.
3. Reassemble in reverse order and check with wiring
diagram for correct reconnection.
Conversion from Natural Gas to LPG
It is important to note that this model is designed for
use with natural gas but can be converted for use with
butane or propane gas providing the correct injectors
are fitted. The gas rate is adjusted to suit.
Method
• Ensure that the gas taps are in the 'OFF' position
• Isolate the hob from the electrical supply
• Remove all pan supports, burner caps, rings, crowns
and control knobs.
• With the aid of a 7mm box spanner the burner
injectors can then be unscrewed and replaced by the
appropriate LPG injectors.
TO ADJUST THE GAS RATE
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw, which is
located down the centre of the gas tap control shaft.
Upon completion stick the replacement rating plate
on the under side of the hob.
IMPORTANT
The replacement/conversion of the gas hob should
only be undertaken by a competent person.
19