Asus RT-N14U User guide

User Guide
RT-N14U
Wireless-N300 Router
E7879
First Edition
November 2012
Copyright © 2012 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described
in it, may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language in any form or by any means, except
documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired,
modified or altered, unless such repair, modification of alteration is authorized
in writing by ASUS; or (2) the serial number of the product is defaced or
missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS,
EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS
AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR
PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE
FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE
AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A
COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY
FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be
registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent
to infringe.
Table of contents
About this guide........................................................................................... 5
Package contents......................................................................................... 7
1
Getting to know your router
7
Hardware features........................................................................................ 8
Mounting placement................................................................................10
Positioning your router............................................................................11
2
Setting up your wireless network
11
What you need............................................................................................12
Setting up your wireless router.............................................................13
Wired connection................................................................................13
Wireless connection...........................................................................14
Before you proceed............................................................................15
A. Disable any configured proxy servers................................15
B. Configure TCP/IP settings.......................................................17
C. Disable dial-up networking...................................................19
Logging into the web GUI.......................................................................20
3
Network configuration using the web GUI
20
Setting up the Internet connection.....................................................21
Quick Internet Setup (QIS) with auto-detection......................21
Setting up the wireless security settings...........................................26
Managing your network clients............................................................27
Monitoring your USB device...................................................................27
Creating your Guest Network................................................................29
Using the Traffic Manager........................................................................31
Managing QoS (Quality of Service) Bandwidth........................31
Monitoring Traffic . .............................................................................32
Using the USB application.......................................................................33
Using AiDisk for File Sharing...........................................................33
Using the Servers Center..................................................................36
Using the Network Place (Samba) Share service.....................37
Using the FTP Share service............................................................39
Using the Miscellaneous setting....................................................42
Configuring Advanced settings............................................................43
Setting up the DHCP Server............................................................43
Upgrading the firmware...................................................................44
Restoring/Saving/Uploading settings.........................................45
Setting up your network printer...........................................................46
4
Using the utilities
49
Device Discovery........................................................................................49
Firmware Restoration................................................................................50
5
Troubleshooting
53
Troubleshooting.........................................................................................53
ASUS DDNS Service...................................................................................56
Frequently Asked Questions (FAQs).............................................56
Appendices
59
Notices............................................................................................................59
ASUS Contact information......................................................................71
Networks Global Hotline Information.................................................72
About this guide
This user guide contains information that you need to install and
configure the ASUS Router.
How this guide is organized
This guide contains the following sections:
• Chapter 1: Getting to know your router
This chapter provides information on the package contents,
hardware features, and LED indicators of the ASUS Router.
• Chapter 2: Setting up your wireless network
This chapter details instructions on how to set up a wireless
network.
• Chapter 3: Network configuration using the web GUI
This chapter discusses the steps to configure a wireless network
using the web GUI.
• Chapter 4: Using the utilities
This chapter provides instructions on using the utilities
included with the ASUS router.
• Chapter 5: Troubleshooting
This chapter contains a troubleshooting guide for solving
common problems you may encounter when using the ASUS
Router.
• Appendices
This chapter provides you with the regulatory Notices and
Safety Statements.
1
Getting to know
your router
Package contents
RT-N14U Wireless Router
Network cable (RJ-45)
Power adapter
Quick Start Guide
Warranty card
• If any of the items is damaged or missing, contact ASUS for
technical inquiries and support, Refer to the ASUS Support
Hotline list at the back of this user manual.
• Keep the original packaging material in case you would need
future warranty services such as repair or replacement.
Chapter 1: Getting to know your router
RT-N14U
Hardware features
Front
1
2
3
4
5
1
USB LED
Off: Indicates no power or no USB device connected.
On: Indicates a connected USB devices.
2
LAN LED
Off: No power or no connection detected.
On: Indicates a connection to a local area network (LAN).
3
Wi-Fi LED
Off: No wireless signal detected.
On: Indicates that the wireless network is ready.
Flashing: Indicates network activity via wireless connection
4
WAN LED
Off: No power or no connection detected.
On: Indicates a connection to a wide area network (WAN).
5
Power LED
Off: No power.
On: Device ready.
Flashing: Indicates WPS activity.
RT-N14U
Chapter 1: Getting to know your router
Rear
66
13
7
8
12
9
10
11
6
USB 2.0 port
Insert USB 2.0 devices such as USB hard drives and desktop printers into
this port.
7
WPS button
Press this button to launch the WPS Wizard to set up wireless security.
8
LAN 1~4 ports
Connect ethernet cables into these ports to establish a LAN connection.
9
WAN (Internet) port
Connect a network cable into this port to establish a WAN connection.
10
Power button
Press the power button to switch the device ON/OFF.
11
Power (DC-IN) port
Insert the bundled AC adapter into this port.
12
Reset button
This button resets or restores the system to its factory default settings.
13
Wall-mount hooks
Use the wall-mount hooks to mount the ASUS router to a wall or raised
surface.
Chapter 1: Getting to know your router
RT-N14U
Mounting placement
To mount the wireless router onto
its stand:
1. Locate the two mounting holes
at the bottom of the wireless
router.
2. Latch the stand’s two mounting
hooks to the wireless router’s
mounting holes.
3. Slide the wireless router towards
direction of the arrow to secure
it to its stand.
2
2
3
• Use only the power adapter that came with your package.
Using other adapters may damage the device.
• Operating Specifications:
DC Power adapter
DC Output:
+19V with max 1.58A current; +12V
with max 2A current
Operating Temperature
0~40oC
Storage
0~70oC
Operating Humidity
50~90%
Storage
20~90%
•
10
RT-N14U
Chapter 1: Getting to know your router
2
Setting up your
wireless network
Positioning your router
To get the best wireless network performance from your ASUS
router, follow the recommendations below:
• Place the wireless router at the center of your network for
maximum wireless coverage.
• Keep the device away from metal obstructions and away from
direct sunlight.
• Keep the device away from 802.11g or 20MHz only Wi-Fi
devices, 2.4GHz computer peripherals, Bluetooth devices,
cordless phones, transformers, heavy-duty motors, fluorescent
lights, microwave ovens, refrigerators, and other industrial
equipment to prevent signal interference or loss.
• For the best front-to-rear coverage, place the wireless router in
an upright position.
• For the best up-and-down coverage, place the wireless router
in an inclined position.
• Always update to the latest firmware. Visit the ASUS website at
http://www.asus.com to get the latest firmware updates.
Chapter 2: Setting up your wireless network
RT-N14U
11
What you need
To set up your network, you need one or two computers that meet
the following system requirements:
•
•
•
•
Ethernet RJ-45 (LAN) port (10Base-T/100Base-TX)
IEEE 802.11 b/g/n wireless capability
An installed TCP/IP service
Web browser such as Internet Explorer, Firefox, Safari, or
Google Chrome
• If your computer does not have built-in wireless capabilities,
you may install an IEEE 802.11 b/g/n WLAN adapter to your
computer to connect to the network.
• If you are using only one computer with a single band
IEEE 802.11 b/g/n WLAN adapter, you will be limited to using
only the 2.4GHz frequency.
• Ethernet RJ-45 cables used to connect the network devices
should not exceed 100 meters.
12
RT-N14U
Chapter 2: Setting up your wireless network
Setting up your wireless router
Use a wired connection in setting up your wireless router to
avoid possible wireless setup issues.
Before setting up your ASUS wireless router, do the following:
• If you are replacing an existing router, disconnect it from
your network.
• Disconnect the cables/wires from your existing modem
setup. If your modem has a backup battery, remove it as
well.
• Reboot your computer (recommended).
Wired connection
Your wireless router has an integrated auto-crossover feature
that allows the use of either a straight-through or crossover
cable when setting up a wired connection.
4
Modem
2
3
1
To set up a wired connection:
1. Insert your wireless router’s AC adapter into the DC-In port and
plug it to a power outlet.
Chapter 2: Setting up your wireless network
RT-N14U
13
2. Using the bundled network cable, connect your computer to
your wireless router’s LAN port.
Once the ethernet cable is connected, check that the LAN LED is
blinking.
3 Using another network cable, connect your modem to your
wireless router’s WAN port.
4. Insert your modem’s AC adapter into the DC-In port and plug it
to a power outlet.
Wireless connection
3
Modem
2
1
To set up a wireless connection:
1. Insert your wireless router’s AC adapter into the DC-In port and
plug it to a power outlet.
2 Using the bundled network cable, connect your modem to your
wireless router’s WAN port.
3. Insert your modem’s AC adapter to the DC-In port and plug it
to a power outlet.
4. Install an IEEE 802.11 b/g/n WLAN adapter on your computer.
14
RT-N14U
Chapter 2: Setting up your wireless network
• For details on connecting to a wireless network, refer to the
WLAN adapter’s user manual.
• To set up the security settings for your network, refer to the
section Setting up wireless security settings.
Before you proceed
Before configuring your wireless router, apply the steps
described in this section to each computer on the network to
avoid problems conneting to the wireless network.
A. Disable any configured proxy servers.
Windows® 7
1. Click Start > Internet
Explorer.
2. Click Tools >
Internet options >
Connections tab >
LAN settings.
Chapter 2: Setting up your wireless network
RT-N14U
15
3. From the Local Area
Network (LAN) Settings
window, uncheck Use a
proxy server for your LAN.
4. Click OK then Apply.
MAC OSX
1. From your Safari
browser, click Safari
> Preferences >
Advanced. On the
Proxies item, click
Change Settings...
2. From the Network
screen, deselect FTP
Proxy and Web Proxy
(HTTP).
3. Click OK then Apply.
16
RT-N14U
Chapter 2: Setting up your wireless network
B. Configure TCP/IP settings to automatically
obtain an IP address.
Windows® 7
1. Click Start > Control Panel
> Network and Internet
> Network and Sharing
Center > Change adapter
settings.
2. On the Network Connections
window, click on Local Area
Connection.
3. On the Local Area Connection
Network Status window, click
Properties.
4. Select Internet Protocol
Version 4 (TCP/IPv4) or
Internet Protocol Version
6 (TCP/IPv6), then click
Properties.
Chapter 2: Setting up your wireless network
RT-N14U
17
6. Tick Obtain an IP address
automatically.
7. Click OK.
MAC OSX
1. Click Apple Menu
>System Preferences >
Network
2. Click Ethernet on the
left panel.
3. On the Configure IPv4,
item select Using
DHCP.
4. Cllick Apply.
18
RT-N14U
Chapter 2: Setting up your wireless network
C. Disable dial-up networking
Windows® 7
1. Click Start > Internet
Explorer.
2. Click Tools > Internet
options > Connections
tab.
3. Tick Never dial a
connection.
4. Click Apply then OK.
Chapter 2: Setting up your wireless network
RT-N14U
19
3
Network configuration
using the web GUI
Logging into the web GUI
Your ASUS Wireless Router uses a web-based user interface that
allows you to configure the router using any web browser such as
Internet Explorer, Firefox, Safari, or Google Chrome.
To log in to the web GUI:
1. Launch your web browser and manually key in the wireless
router’s default IP address: 192.168.1.1
2. On the login page, key in the default user name (admin) and
password (admin).
20
RT-N14U
Chapter 3: Network Configuration using the web GUI
3. The wireless router GUI provides access to various
configuration settings.
Setting up the Internet connection
When setting the Internet connection for the first time, press
the Reset button on your wireless router to reset it to its factory
default settings.
Quick Internet Setup (QIS) with auto-detection
The Quick Internet Setup (QIS) feature guides you in quickly
setting up your Internet connection.
To use QIS with auto-detection:
1. Launch a web browser such as Internet Explorer, Mozilla Firefox,
Safari, or Google Chrome.
Chapter 3: Network Configuration using the web GUI
RT-N14U
21
2. Quick Internet Setup will launch automatically. Click Next.
3. Key in a new administrator password. Click Next.
4. Select Wireless router mode or Access Point (AP) mode. Click
Next.
To set up a wireless network with Internet access, use Wireless
router mode.
22
RT-N14U
Chapter 3: Network Configuration using the web GUI
5. The wireless router will attempt to identify your connection
type.
6. Select the necessary connection type and key in any necessary
information required such as your ISP username and password.
Obtain the necessary information about your Internet
connection type and additional login information from your
Internet Service Provider.
Chapter 3: Network Configuration using the web GUI
RT-N14U
23
• Auto-detection of your ISP connection type takes place when
you configure the wireless router for the first time or when
your wireless router is reset to its default settings.
• If QIS fails, you can select the connection type manually.
7. Follow the setup wizard, which will give you the option to
specify a host name, a MAC address, and a DNS server. Click
Next.
8. In the Wireless setting screen, key in a network name (SSID)
and assign a security key for your wireless connection. Click
Apply.
24
RT-N14U
Chapter 3: Network Configuration using the web GUI
9. A summary of your network settings will be displayed. Click
Next to continue.
10.The Wireless Network Connection Tutorial will be displayed.
Click Finish.
Chapter 3: Network Configuration using the web GUI
RT-N14U
25
Setting up the wireless security settings
To protect your wireless network from unauthorized access, you
need to configure the security settings of the wireless router.
To set up wireless security settings:
1. Key in 192.168.1.1 on your web browser.
2. On the login screen, key in the default user name (admin) and
password (admin), then click OK.
3. On the Network Map screen, click the System Status icon
to display the wireless security settings. The System Status
panel on the right will display the wireless network name,
authentication method, and encryption settings.
Wi-Fi security settings
26
RT-N14U
Chapter 3: Network Configuration using the web GUI
Managing your network clients
To manage your network clients:
1. On the Network Map screen, click the Client Status icon to list
currently connected network clients.
Monitoring your USB device
The ASUS Wireless Router provides one USB 2.0 port for
connecting USB devices such as a USB storage device or desktop
printer.
To use this feature, connect a USB storage device, such as a USB
hard disk or USB flash drive, to the USB 2.0 port on the rear
panel of your wireless router. The USB storage device should be
formatted and partitioned properly. Refer to the Plug-n-Share
Disk Support List for disk format, file and partition size at
http://event.asus.com/networks/disksupport
Chapter 3: Network Configuration using the web GUI
RT-N14U
27
You first need to create user accounts to allow other network
clients to access the USB device. For more details, refer to the
section Using AiDisk for File Sharing in this user manual.
To monitor your USB device:
1. On the Network Map screen, select the USB Disk Status icon to
display information about your USB device.
The wireless router works with most USB HDDs/Flash disks (up
to 2TB size) and supports read-write access for FAT16, FAT32,
EXT2, EXT3, and NTFS formatted storage.
To safely remove your USB device:
1. Click the USB icon on the upper-right corner. Click Eject USB disk.
To avoid data loss or damage to the USB storage device, always
eject your USB device before disconnecting it from the USB
port.
28
RT-N14U
Chapter 3: Network Configuration using the web GUI
Creating your Guest Network
Setting up a Guest Network provides wireless Internet
connectivity for temporary visitors while restricting access to your
private network.
To create your guest network:
1. Click Guest Network on the left navigation panel.
2. Click Enable.
3. To configure additional options, click Modify.
Chapter 3: Network Configuration using the web GUI
RT-N14U
29
4. Click Yes on the Enable Guest Network? item.
5. Assign a wireless name for your temporary network on the
Network Name (SSID) field.
6. Select an Authentication Method.
7. Select a WEP Encryption method.
8. Specify the Access time or click Limitless.
9. Select Disable or Enable on the Access Intranet item.
10. Click Apply.
30
RT-N14U
Chapter 3: Network Configuration using the web GUI
Using the Traffic Manager
Managing QoS (Quality of Service) Bandwidth
The Quality of Service feature allows you to set the bandwidth
priority and manage network traffic.
To set up QoS:
1. Click Traffic Manager on the left navigation panel and click the
QoS tab.
2. Click ON to enable QoS and click Save.
Your bandwidth information is available from your ISP.
3. If you want to prioritize specific network applications and
network services, click User-define QoS rules on the upperright hand corner.
Chapter 3: Network Configuration using the web GUI
RT-N14U
31
3. Online service types, source IP addresses, ports, and protocols
can be added and configured in the QoS rules screen.
Monitoring Traffic
Click the Traffic Monitor tab to view real-time or historical
bandwidth information of your Internet, Wired, and Wireless
connections.
32
RT-N14U
Chapter 3: Network Configuration using the web GUI
Using the USB application
The USB application menu displays several options including
AiDisk, Servers Center, and Network Printer Server.
Using AiDisk for File Sharing
AiDisk allows you to share files stored in a connected USB storage
device through the network.
Before using AiDisk, connect a USB storage device, such as a
USB hard disk or USB flash drive, to the USB 2.0 port on the rear
panel of your wireless router. The USB storage device should be
formatted and partitioned properly. Refer to the Plug-n-Share
Disk Support List for disk format, file and partition size at
http://event.asus.com/networks/disksupport
To avoid data loss or damage to the USB storage device, always
follow the steps to safely remove your USB device.
Chapter 3: Network Configuration using the web GUI
RT-N14U
33
To use AiDisk:
1. Click USB application on the left navigation panel and click
the AiDisk icon.
2. From the Welcome to AiDisk wizard screen, click Go.
3. Assign access rights to the USB storage device. Select limitless
access rights, limited access rights, and admin access to
define read-right privileges to files stored in the USB storage
device. Click Next.
34
RT-N14U
Chapter 3: Network Configuration using the web GUI
4. To set up your domain name via the ASUS DDNS service, select
I will use the service and accept Terms of service and key in
your preferred domain name. Your domain name will follow the
format xxx.asuscomm.com, where xxx is your host name.
5. Click Next.
6. Click Finish.
7. To access the USB storage device via FTP from a client on the
network, launch a web browser or a third-party FTP client utility
and key in the ftp link (ftp://<domain name>) you previously
created.
Chapter 3: Network Configuration using the web GUI
RT-N14U
35
Using the Servers Center
Your ASUS wireless router supports UPnP (Universal Plug and Play)
multimedia devices, such as the Sony Playstation 3 and Microsoft
XBox360. Setting up the Servers Center feature allows UPnP
devices to access multimedia files from the USB disk connected to
your wireless router.
To make use of the UPnP Media Server feature wirelessly, your
UPnP device should have a wireless adapter.
To set up your wireless router as a Server center for UPnP
devices:
1. Click USB application on the left navigation panel and click
the Servers Center icon.
2. Slide the Enabled DLNA media server switch to ON to stream
multimedia via DLNA.
Slide the Enabled iTunes server switch to ON to stream
multimedia via iTunes.
36
RT-N14U
Chapter 3: Network Configuration using the web GUI
Using the Network Place (Samba) Share service
The Network Place (Samba) Share feature allows Mac OSX,
Windows, and Linux clients to access files on the USB storage
device.
To use Samba share:
1. Click USB application on the left navigation panel and click
the Servers Center icon.
2. Click the Network place (Samba) Share tab.
3. Click the Enable Share and Share with account.
4. Click the Add button to create user accounts for users who will
be accessing the USB storage device via Samba.
Chapter 3: Network Configuration using the web GUI
RT-N14U
37
5. Assign a name for the user account and key in a password. Click
Add.
6. Use the Modify and Delete buttons to modify the password or
remove the user account.
7. Select a user and assign the type of access rights for files or
folders located in the storage device:
• R/W: Select this option to assign read/write access for a
specific file/folder.
• R: Select this option to assign read only access for a specific
file/folder.
• No: Select this option if you do not want to share a specific
file/folder.
8. Click Apply.
38
RT-N14U
Chapter 3: Network Configuration using the web GUI
Using the FTP Share service
Your ASUS wireless router can set up the connected USB storage
device as an FTP server.
To set up the FTP Share service:
1. Configure file sharing using the steps in Using AiDisk for File
Sharing.
2. Enable the DDNS service for FTP server access:
a. Click WAN on the left navigation panel, then click the
DDNS tab.
b. In the Enable the DDNS Client? field, tick Yes.
c. Select your DDNS Server from the list.
d. Key in your Host Name.
e. Click Apply.
Chapter 3: Network Configuration using the web GUI
RT-N14U
39
3. Click USB application on the left navigation panel and click
the Servers Center icon.
4. Click the FTP Share tab.
5. Click the Enable FTP and Share with account.
6. Click the Add button to create accounts for users who will be
accessing the USB storage device via FTP Server.
Assign a name for the user account and key in a password. Click
Add.
7. Use the Modify and Delete buttons to modify the password or
remove the user account.
40
RT-N14U
Chapter 3: Network Configuration using the web GUI
8. Select the type of access rights for the storage device:
• R/W: Select this option to assign read/write access for a
specific file/folder.
• W: Select this option to assign write only access for a
specific file/folder.
• R: Select this option to assign read only access for a specific
file/folder.
• No: Select this option if you do not want to share a specific
file/folder.
9. Click Apply.
10.To access the FTP server from a client on the network, key
in ftp://<hostname>.asuscomm.com on a web browser or
a third-party FTP utility. Once prompted, key in the account
username and password you set up in Step 6.
Chapter 3: Network Configuration using the web GUI
RT-N14U
41
Using the Miscellaneous setting
The Miscellaneous settings page allows you to configure
additional properties for the USB disk. You can change the
maximum number of users who can access the USB storage
device, assign a device name and work group, or specify the
language settings for the FTP server.
To configure additional USB device settings:
1. Click USB application on the left navigation panel and click
Servers Center.
2. Click the Miscellaneous setting tab.
3. Specify or change configuration settings as needed.
3. Click Apply.
42
RT-N14U
Chapter 3: Network Configuration using the web GUI
Configuring Advanced settings
Setting up the DHCP Server
You wireless router uses DHCP to assign IP addresses
automatically on your network. You can specify the IP address
range and lease time for the clients on your network.
To configure the DHCP server:
1. Click LAN on the left navigation panel.
2. Click the DHCP Server tab.
3. In the Enable the DHCP Server? field, tick Yes.
4. In the IP Pool Starting Address field, key in the starting IP
address.
5. In the IP Pool Ending Address field, key in the ending IP
address.
Chapter 3: Network Configuration using the web GUI
RT-N14U
43
6. In the Lease Time field, specify in seconds when an assigned
IP address will expire. Once it reaches this time limit, the DHCP
server will then assign a new IP address.
• ASUS recommeds that you use an IP address format of
192.168.1.xxx (where xxx can be any number between 2 and
254) when specifying an IP address range.
• An IP Pool Starting Address should not be greater than the IP
Pool Ending Address.
Upgrading the firmware
Download the latest firmware from the ASUS website at http://
www.asus.com
To upgrade the firmware:
1. Click Administration from the left navigation panel.
2. Click the Firmware Upgrade tab.
3. In the New Firmware File item, click Browse. Navigate to the
downloaded firmware file.
4. Click Upload.
If the upgrade process fails, the wireless router automatically
enters rescue mode and the power LED indicator on the front
panel starts flashing slowly. To recover or restore the system, use
the Firmware Restoration utility.
44
RT-N14U
Chapter 3: Network Configuration using the web GUI
Restoring/Saving/Uploading settings
To restore/save/upload the settings:
1. Click Advanced Setting from the left navigation panel.
2. Click the Restore/Save/Upload Setting tab.
3. Select the tasks that you want to do:
• To restore to the default factory settings, click Restore, and
click OK once prompted.
• To save the current system settings, click Save, navigate to
the folder where you intend to save the file and click Save.
• To restore from a saved system settings file, click Browse to
locate your file, then click Upload.
Chapter 3: Network Configuration using the web GUI
RT-N14U
45
Setting up your network printer
Use the Network Printer Setup utility to set up a USB printer on
your wireless router and share the printer with other devices on
the network.
• To check if your USB printer is compatible with your ASUS
wireless router, refer to the Plug-n-Share Disk Support List at
http://event.asus.com/networks/printersupport
• The wireless router's printer server function is not supported
on Windows® 2000.
To set up your USB Printer:
1. Click USB application from the left navigation panel, then click
Network Printer Server.
2. Click Download Now! to download the network printer utility.
3. Unzip the downloaded file and click the Printer.exe file to run
the network printer setup program.
46
RT-N14U
Chapter 3: Network Configuration using the web GUI
4. Follow the onscreen instructions to set up your hardware, then
click Next.
5. Wait for a few minutes for the initial setup to finish. Click Next.
6. Click Finish to complete the installation.
Chapter 3: Network Configuration using the web GUI
RT-N14U
47
7. Follow the Windows® OS instructions to install the printer driver.
8. After printer driver installation is complete, computers on the
network will now be able to access the printer.
48
RT-N14U
Chapter 3: Network Configuration using the web GUI
4
Using the utilities
Device Discovery
Device Discovery is an ASUS WLAN utility that detects an ASUS
wireless router device, and enables you to configure the device.
To launch the Device Discovery utility:
• From your computer’s desktop, click
Start > All Programs > ASUS Utility > RT-N14U Wireless
Router > Device Discovery.
When you set the router to Access Point mode, you need to use
Device Discovery to get the router’s IP address.
Chapter 4: Using the Utilities
RT-N14U
49
Firmware Restoration
Firmware Restoration is used on an ASUS Wireless Router after a
failed firmware upgrade. This utility uploads a firmware file to the
wireless router. The process takes about three to four minutes.
Launch rescue mode before using the Firmware Restoration
utility.
To launch rescue mode and use the Firmware Restoration
utility:
1. Unplug the wireless router from its power source.
2. While holding down the Reset button at the back of the
wireless router, plug the wireless router into a power source.
Release the Reset button when the Power LED at the front
panel begins to flash slowly, which indicates that the wireless
router is in rescue mode.
3. Use the following to set up your TCP/IP settings:
IP address: 192.168.1.x
Subnet mask: 255.255.255.0
4. From your computer’s desktop, click
Start > All Programs > ASUS Utility RT-N14U Wireless
Router > Firmware Restoration.
50
RT-N14U
Chapter 4: Using the Utilities
5. Click Browse to navigate to a firmware file, then click Upload.
The Firmware Restoration utility is not used to upgrade the
firmware of a working ASUS Wireless Router. Normal firmware
upgrades must be done through the web GUI. Refer to
Upgrading the firmware for more details.
Chapter 4: Using the Utilities
RT-N14U
51
52
RT-N14U
Chapter 4: Using the Utilities
5
Troubleshooting
Troubleshooting
I cannot access the router GUI for configuring the router.
• Delete the cookies and temporary files in your web browser. To
do this in Internet Explorer 8, follow these steps:
1. Launch your web browser, then click Tools > Internet
Options.
2. On the General tab, click Delete under Browsing history.
3. Tick Temporary Internet Files and Cookies. Click Delete.
The commands for deleting cookies and files vary with the web
browser.
• Disable the proxy server settings, cancel the dial-up connection,
and set the TCP/IP settings to obtain IP addresses automatically.
For more details, refer to the section Before you proceed in
this user manual.
The client cannot establish a wireless connection with the
router.
Out of Range:
• Place the router closer to the wireless client.
• Change the channel settings.
Authentication:
• Use a wired connection to connect to the router.
• Check the wireless security settings.
• Press the Reset button at the rear panel for more than five
seconds.
Chapter 5: Troubleshooting
RT-N14U
53
Cannot find the router:
• Press the Reset button at the rear panel for more than five
seconds.
• Check the setting in the wireless adapter such as SSID and
encryption settings.
Cannot access the Internet via wireless LAN adapter.
• Place the router closer to the wireless client.
• Check whether the wireless adapter is connected to the correct
wireless network.
• Check whether the wireless channel in use conforms to the
channels available in your country/area.
• Check the encryption settings.
• Check if the ADSL or Cable connection is connected.
• Use a different Ethernet cable.
Internet is not accessible.
• Check the status indicators on the ADSL modem and the
wireless router.
• Check if the WAN LED on the wireless router is ON. If the LED is
not ON, switch the ethernet cable and try again.
When the ADSL Modem “Link” light is ON (steady and not
blinking), this means Internet Access is possible.
• Restart your computer.
• Refer to the Quick Start Guide of the wireless router and reconfigure the settings.
• Check if the WAN LED on the wireless router is ON.
• Check the wireless encryption settings.
• Check if the computer can get an IP address (using both a
wired or wireless connection).
• Check that your web browser is configured to use the local
LAN, and is not configured to use a proxy server.
54
RT-N14U
Chapter 5: Troubleshooting
If the ADSL “LINK” light blinks continuously or stays off,
Internet access is not possible - the Router is unable to
establish a connection with the ADSL network.
• Ensure that all your cables are all properly connected .
• Disconnect the power cord from the ADSL or cable modem,
wait a few minutes, then reconnect the cord.
• If the ADSL light continues to blink or stays OFF, contact your
Internet service provider.
Network name or encryption keys are forgotten.
• Set up a wired connection and configure the wireless
encryption again.
• Press the Reset button at the rear panel of the wireless router
for more than five seconds.
How to restore the system to its default settings?
• Press the Reset button at the rear panel of the wireless router
for more than five seconds.
• Refer to the section Restoring/Saving/Uploading settings in
Chapter 3 of this user manual.
The following are the factory default settings:
User Name:
Password:
Enable DHCP:
IP address:
Domain Name:
Subnet Mask:
DNS Server 1:
DNS Server 2:
SSID:
Chapter 5: Troubleshooting
admin
admin
Yes (if WAN cable is plugged in)
192.168.1.1
(Blank)
255.255.255.0
192.168.1.1
(Blank)
ASUS
RT-N14U
55
ASUS DDNS Service
RT-N14U supports the ASUS DDNS service. When exchanging
devices at the service center, if you have registered the ASUS
DDNS service and want to keep the original domain name, you
must transfer your data in order to retain the DDNS service. Visit
your local service center for more information.
• If there is no activity in the domain - such as reconfiguring
the router or accessing the registered domain name - within
90 days, the system automatically deletes the registered
information.
• If you encounter any problem or difficulty in using your
device, contact the service center.
Frequently Asked Questions (FAQs)
1. Will the registered information be lost or registered by
others?
If you have not updated the registered information in 90 days,
the system automatically deletes the registered information
and the domain name may be registered by others.
2. I did not register the ASUS DDNS for the router I bought six
months ago. Can I still register it?
Yes, you can still register the ASUS DDNS service for your router.
The DDNS service is embedded in your router, so you can
register the ASUS DDNS service anytime. Before registering,
click Query to check if the hostname has been registered or
not. If not, the system registers the hostname automatically.
56
3. I have registered a domain name before and it has been
working well until my friends told me that they could not
access my domain name.
Check the following:
1. The internet is working properly.
2. The DNS server is working properly.
3. The last time you updated the domain name.
If there are still problems in accessing your domain name,
contact the service center.
4. Can I register two domain names to access my http and ftp
servers separately?
No, you cannot. You can only register one domain name for one
router. Use port mapping to implement security in the network.
5. After restarting the router, why is it that I see a different
WAN IP address in MS-DOS and in the router configuration
page?
This is normal. The interval time between the ISP DNS server
and ASUS DDNS results in different WAN IPs in MS-DOS and in
the router configuration page. Different ISPs may have different
interval time for IP updating.
6. Is the ASUS DDNS service free, or is it just a trial version?
The ASUS DDNS service is a free and embedded service in
some ASUS routers. Check if your ASUS router supports the
ASUS DDNS service.
57
58
Appendices
Notices
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our
commitment to the highest standards for protecting our
environment. We believe in providing solutions for you to be able
to responsibly recycle our products, batteries, other components,
as well as packaging materials. Please go to http://csr.asus.com/
english/Takeback.htm for the detailed recycling information in
different regions.
REACH
In complying with the REACH (Registration, Evaluation,
Authorisation, and Restriction of Chemicals) regulatory
framework, we published the chemical substances in our products
at ASUS REACH website at
http://csr.asus.com/english/index.aspx
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
59
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device works within the 5.15 ~ 5.25 GHz and is restricted
to indoor operations to reduce any potential for harmful
interference to co-channel MSS operations.
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the equipment.
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating
in conjunction with any other antenna or transmitter
Safety Information
To maintain compliance with FCC’s RF exposure guidelines, this
equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body. Use only
the supplied antenna.
60
Declaration of Conformity for R&TTE directive 1999/5/EC
Essential requirements – Article 3
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950-1 has been
conducted. These are considered relevant and sufficient.
Protection requirements for electromagnetic compatibility
– Article 3.1b
Testing for electromagnetic compatibility according to EN
301 489-1 and EN 301 489-17 has been conducted. These are
considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328- 2 has been
conducted. These are considered relevant and sufficient.
CE Mark Warning
This is a Class B product, in a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian ICES-003
and RSS-210.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the ASUS Wireless Device is below
the Industry Canada (IC) radio frequency exposure limits. The
ASUS Wireless Device should be used in such a manner such
61
that the potential for human contact during normal operation is
minimized.
This device has been evaluated for and shown compliant with
the IC Specific Absorption Rate (“SAR”) limits when installed in
specific host products operated in portable exposure conditions
(antennas are less than 20 centimeters of a person’s body).
This device has been certified for use in Canada. Status of the
listing in the Industry Canada’s REL (Radio Equipment List) can be
found at the following web address: http://www.ic.gc.ca/app/sitt/
reltel/srch/nwRdSrch.do?lang=eng
Additional Canadian information on RF exposure also can be
found at the following web: http://www.ic.gc.ca/eic/site/smt-gst.
nsf/eng/sf08792.html
Canada, avis d’Industry Canada (IC)
Cet appareil numérique de classe B est conforme aux normes
canadiennes ICES-003 et RSS-210.
Son fonctionnement est soumis aux deux conditions suivantes: (1)
cet appareil ne doit pas causer d’interférence et (2) cet appareil
doit accepter toute interférence, notamment les interférences qui
peuvent a ecter son fonctionnement.
NCC 警語
經型式認證合格之低功率射頻電機,非經許可,公司、商號或
使用者均不得擅自變更頻率、加大功率或變更原設計之特性及
功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通
信;經發現有干擾現象時,應立即停用,並改善至無干擾時方
得繼續使用。前項合法通信,指依電信法規定作業之無線電通
信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電
波輻射性電機設備之干擾。
62
GNU General Public License
Licensing information
This product includes copyrighted third-party software licensed
under the terms of the GNU General Public License. Please see The
GNU General Public License for the exact terms and conditions
of this license. We include a copy of the GPL with every CD
shipped with our product. All future firmware updates will also be
accompanied with their respective source code. Please visit our
web site for updated information. Note that we do not offer direct
support for the distribution.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public License is intended to guarantee your freedom to share
and change free software--to make sure the software is free for all
its users. This General Public License applies to most of the Free
Software Foundation’s software and to any other program whose
authors commit to using it. (Some other Free Software Foundation
software is covered by the GNU Library General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source code or
63
can get it if you want it, that you can change the software or use
pieces of it in new free programs; and that you know you can do
these things.
To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the
rights. These restrictions translate to certain responsibilities for
you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know
their rights.
We protect your rights with two steps: (1) copyright the software,
and (2) offer you this license which gives you legal permission to
copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make
certain that everyone understands that there is no warranty for
this free software. If the software is modified by someone else and
passed on, we want its recipients to know that what they have is
not the original, so that any problems introduced by others will
not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making
the program proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone’s free use or not
licensed at all.
The precise terms and conditions for copying, distribution and
modification follow.
64
Terms & conditions for copying, distribution, &
modification
0. This License applies to any program or other work which
contains a notice placed by the copyright holder saying it may
be distributed under the terms of this General Public License.
The “Program”, below, refers to any such program or work, and
a “work based on the Program” means either the Program or
any derivative work under copyright law: that is to say, a work
containing the Program or a portion of it, either verbatim or
with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the
term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are
not covered by this License; they are outside its scope. The act
of running the Program is not restricted, and the output from
the Program is covered only if its contents constitute a work
based on the Program (independent of having been made by
running the Program). Whether that is true depends on what
the Program does.
1. You may copy and distribute verbatim copies of the Program’s
source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy
an appropriate copyright notice and disclaimer of warranty;
keep intact all the notices that refer to this License and to the
absence of any warranty; and give any other recipients of the
Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program or any
portion of it, thus forming a work based on the Program, and
copy and distribute such modifications or work under the
terms of Section 1 above, provided that you also meet all of
these conditions:
65
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the date of any
change.
b) You must cause any work that you distribute or publish, that
in whole or in part contains or is derived from the Program or
any part thereof, to be licensed as a whole at no charge to all
third parties under the terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print or
display an announcement including an appropriate copyright
notice and a notice that there is no warranty (or else, saying
that you provide a warranty) and that users may redistribute
the program under these conditions, and telling the user how
to view a copy of this License. (Exception: if the Program itself is
interactive but does not normally print such an announcement,
your work based on the Program is not required to print an
announcement.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and
separate works in themselves, then this License, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections
as part of a whole which is a work based on the Program, the
distribution of the whole must be on the terms of this License,
whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who wrote
it.
Thus, it is not the intent of this section to claim rights or contest
your rights to work written entirely by you; rather, the intent is
to exercise the right to control the distribution of derivative or
collective works based on the Program.
In addition, mere aggregation of another work not based on
the Program with the Program (or with a work based on the
Program) on a volume of a storage or distribution medium
66
does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on
it, under Section 2) in object code or executable form under the
terms of Sections 1 and 2 above provided that you also do one
of the following:
a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of Sections 1 and 2 above on a medium customarily used
for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than your
cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to
be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the
offer to distribute corresponding source code. (This alternative
is allowed only for noncommercial distribution and only if you
received the program in object code or executable form with
such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of
the work for making modifications to it. For an executable
work, complete source code means all the source code for all
modules it contains, plus any associated interface definition
files, plus the scripts used to control compilation and
installation of the executable. However, as a special exception,
the source code distributed need not include anything that
is normally distributed (in either source or binary form) with
the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that
component itself accompanies the executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place
counts as distribution of the source code, even though third
parties are not compelled to copy the source along with the
object code.
67
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program
is void, and will automatically terminate your rights under
this License. However, parties who have received copies, or
rights, from you under this License will not have their licenses
terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have
not signed it. However, nothing else grants you permission to
modify or distribute the Program or its derivative works. These
actions are prohibited by law if you do not accept this License.
Therefore, by modifying or distributing the Program (or any
work based on the Program), you indicate your acceptance
of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Program or works based
on it.
6. Each time you redistribute the Program (or any work based
on the Program), the recipient automatically receives a license
from the original licensor to copy, distribute or modify the
Program subject to these terms and conditions. You may not
impose any further restrictions on the recipients’ exercise of
the rights granted herein. You are not responsible for enforcing
compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order,
agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this
License. If you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute
the Program at all. For example, if a patent license would not
permit royalty-free redistribution of the Program by all those
who receive copies directly or indirectly through you, then the
only way you could satisfy both it and this License would be to
refrain entirely from distribution of the Program.
68
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended to
apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose
of protecting the integrity of the free software distribution
system, which is implemented by public license practices.
Many people have made generous contributions to the wide
range of software distributed through that system in reliance
on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software
through any other system and a licensee cannot impose that
choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in
certain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the Program under
this License may add an explicit geographical distribution
limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In
such case, this License incorporates the limitation as if written
in the body of this License.
9. The Free Software Foundation may publish revised and/or new
versions of the General Public License from time to time. Such
new versions will be similar in spirit to the present version, but
may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the
Program specifies a version number of this License which
applies to it and “any later version”, you have the option of
following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If
the Program does not specify a version number of this License,
you may choose any version ever published by the Free
Software Foundation.
69
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to
the author to ask for permission.
For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing
and reuse of software generally.
NO WARRANTY
11BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR
ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE
THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
70
ASUS Contact information
ASUSTeK COMPUTER INC. (Asia Pacific)
Address
Website
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
www.asus.com.tw
Technical Support
Telephone
Support Fax
Online support
+886228943447
+886228907698
support.asus.com
ASUS COMPUTER INTERNATIONAL (America)
Address
Telephone
Fax
Website
Online support
800 Corporate Way, Fremont, CA 94539, USA
+15107393777
+15106084555
usa.asus.com
support.asus.com
ASUS COMPUTER GmbH (Germany and Austria)
Address
Telephone
Fax
Website
Online contact
Harkort Str. 21-23, D-40880 Ratingen, Germany
+491805010923*
+492102959911
www.asus.de
www.asus.de/sales
Technical Support
Telephone (Component, Networking)
Telephone (System/Notebook/Eee/LCD)
Fax
Online support
+491805010923*
+491805010920*
+492102959911
support.asus.com
* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.
Manufacturer:
ASUSTeK Computer Inc.
Address:
4F, No.150, LI-TE RD., PEITOU, TAIPEI 112,
TAIWAN, R.O.C.
Authorised representative in
Europe:
ASUS Computer GmbH
Address:
HARKORT STR. 21-23, 40880 RATINGEN,
GERMANY
71
Networks Global Hotline Information
Support
Languages
Working
Hour
Working
Day
8:00-20:00
9:00-18:00
9:00-17:00
9:00-17:00
Mon. to Fri.
Mon. to Fri.
Mon. to Fri.
Mon. to
Sun.
Mon. to Fri.
10:00-18:00
Mon. to Fri.
0033-170949400
English
German
Dutch /French
Simplified
Chinese
Denish/English
Finnish/English/
Swedish
France
Mon. to Fri.
Greece
00800-44-14-20-44
Greek
9:00-17:45
9:00-13:00;
14:00-18:00
Hong Kong
3582-4770
Cantonese/
Chinese/
English
Ireland
0035-31890719918
English
Italy
199-400089
Italian
Japan
0800-123-2787
Japanese
Malaysia
+603 2148 0827 (Check
Repair Detail Status
Only)
+603-6279-5077
Netherlands
/ Luxembourg
Area
Hotline Number
Australia
Austria
Belgium
1300-2787-88
0043-820240513
0032-78150231
China
400-620-6655
Denmark
0045-3832-2943
Finland
00358-9693-7969
France
10:00-20:00
Mon. to Fri.
Mon. to Fri.
10:00-17:00
9:00-17:00
09:00-13:00
14:00-18:00
9:00-18:00
9:00-17:00
Sat.
Mon. to Fri.
Bahasa Melayu/
English
10:00-19:00
Mon. to Fri.
0031-591-570290
Dutch / English
9:00-17:00
Mon. to Fri.
New Zealand
0800-278-788 /
0800-278-778
English
8:00-20:00
Mon. to Fri.
Norway
0047-2316-2682
Norwegian
/English
9:00-17:00
Mon. to Fri.
Philippine
+632-636 8504;
180014410573
00225-718-033
00225-718-040
707-500-310
English
9:00-18:00
Mon. to Fri.
Poland
Portugal
72
9:00-18:00
Polish
Portuguese
9:00-17:00
8:30-17:30
9:00-17:00
Mon. to Fri.
Mon. to Fri.
Sat. to Sun.
Mon. to Fri.
Mon. to Fri.
Area
Hotline Number
Support
Languages
Working
Hour
Working
Day
Russia
Russian/
English
9:00-18:00
Mon. to Fri.
11:00-19:00
Mon. to Fri.
Slovak
Spain
+8-800-100-ASUS; +7495-231-1999
+65-6720-3835
(Check Repair Detail
Status Only)
-66221701
00421-232-162-621
902-88-96-88
8:00-17:00
9:00-18:00
Mon. to Fri.
Mon. to Fri.
Sweden
0046-8587-6940
Czech
Spanish
Swedish/
English
German/French
French
Italian
Traditional
Chinese
9:00-17:00
Mon. to Fri.
9:00-18:00
9:00-17:45
9:00-17:00
9:00-12:00;
13:30-18:00
Mon. to Fri.
Mon. to Fri.
Mon. to Fri.
Thai/English
9:00-18:00
Mon. to Fri.
Turkish
09:00-18:00
Mon. to Fri
English
9:00-17:00
Mon. to Fri.
Mon. to Fri.
English
8:30-12:00am
EST
(5:30am9:00pm PST)
9:00am6:00pm EST
(6:00am3:00pm PST)
Singapore
Switzerland
Taiwan
Thailand
Turkey
United Kingdom
USA/Canada
0041-848111010
0041-848111014
0041-848111012
0800-093-456;
02-81439000
+662-679-8367 -70; 001
800 852 5201
+90-216-524-3000
0044-870-1208340;
0035-31890719918
1-812-282-2787
English
Mon. to Fri.
Sat. to Sun.
For more information, visit the ASUS support site at:
http://support.asus.com
73
Manufacturer:
Authorised
representative
in Europe:
Authorised
distributors
in Turkey:
ASUSTeK Computer Inc.
Tel:
+886-2-2894-3447
Address: No. 150, LI-TE RD., PEITOU,
TAIPEI 112, TAIWAN
ASUS Computer GmbH
Address: HARKORT STR. 21-23, 40880
RATINGEN, GERMANY
BOGAZICI BIL GISAYAR SAN. VE TIC.
A.S.
Tel:
+90 212 3311000
Address: AYAZAGA MAH.
KEMERBURGAZ CAD. NO.10
AYAZAGA/ISTANBUL
CIZGI Elektronik San. Tic. Ltd. Sti.
Tel:
+90 212 3567070
Address: CEMAL SURURI CD. HALIM
MERIC IS MERKEZI
No: 15/C D:5-6 34394
MECIDIYEKOY/ISTANBUL
EEE Yönetmeliğine Uygundur.
74