Bosch NPD-6001A Installation manual

High PoE Midspan 60W, Single port, AC in
NPD-6001A
en
Installation Manual
High PoE Midspan 60W,
Single port, AC in
Table of Contents | en
3
Table of contents
1
Safety
4
1.1
Conventions in this Manual
4
1.2
About this Manual
5
1.3
Important Safety Instructions
5
1.4
Customer Support and Service
7
2
Unpacking
9
2.1
Parts List
9
2.2
Additional Parts Required
9
2.3
Tools Required
10
2.4
Additional Parts Recommended But Not Required
10
3
System overview
11
4
Installation
12
5
Connection
14
6
Troubleshooting
16
Bosch Security Systems
Installation Manual
2013.03 | 1.2 | F.01U.279.929
4
High PoE Midspan 60W,
Single port, AC in
en | Safety
1
Safety
1.1
Conventions in this Manual
In this manual, the following symbols and notations are used to
draw attention to special situations:
Danger!
This symbol indicates an imminently hazardous situation such as
“Dangerous Voltage” inside the product. If not avoided, this will
result in an electrical shock, serious bodily injury, or death.
Warning!
!
Indicates a potentially hazardous situation. If not avoided, this
could result in serious bodily injury or death.
Caution!
Medium Risk
!
Indicates a potentially hazardous situation. If not avoided, this
may result in minor or moderate injury. Alerts the user to important instructions accompanying the unit.
Caution!
!
Indicates a potentially hazardous situation. If not avoided, this
may result in property damage or risk of damage to the unit.
Notice!
i
This symbol indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property.
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
High PoE Midspan 60W,
Single port, AC in
1.2
Safety | en
5
About this Manual
This manual has been compiled with great care and the
information it contains has been thoroughly verified. The text
was complete and correct at the time of printing. Because of the
ongoing development of products, the content of the manual
may change without notice. Bosch Security Systems accepts no
liability for damage resulting directly or indirectly from faults,
incompleteness, or discrepancies between the manual and the
product described.
1.3
Important Safety Instructions
Read, follow, and retain for future reference all of the following
safety instructions. Heed all warnings on the unit and in the
operating instructions before operating the unit.
–
The unit is intended only for installation in a Restricted
Access Location.
–
Installation and removal of the midspan must be carried out
by qualified personnel only.
–
Follow basic electricity safety measures whenever
connecting the midspan to its power source.
–
AC Power Cord Set: Although the High PoE Midspan 60W,
Single port ships with one (1) 120 V power cord and one
(1) 230 V power cord, please note the following as it
applies to your region:
–
The power cord must have regulatory agency approval
for the specific country in which it is being used (i.e.,
UL, CSA, VDE, etc.).
–
The power cord must be a three-conductor type (two
current carrying conductors; one ground conductor)
terminated on one end by an IEC 60320 appliance
coupler (for connection to the midspan), and on the
other end by a plug containing a ground (earthing)
contact.
Bosch Security Systems
Installation Manual
2013.03 | 1.2 | F.01U.279.929
6
High PoE Midspan 60W,
Single port, AC in
en | Safety
–
The power cord must be rated for a minimum of 250
VAC RMS operation, with a minimum rated current
capacity of 5 Amps (or a minimum wire gauge of 18
AWG (0.75mm2).
–
Midspans installed in Australia require power cords
with a minimum wire gauge of 16 AWG (1.0 mm2).
–
A voltage mismatch can cause equipment damage and may
pose a fire hazard. If the voltage indicated on the label is
different from the power outlet voltage, do not connect the
midspan to this power outlet.
–
The AC wall socket-outlet must be near the midspan and
easily accessible. You can remove AC power from the
midspan by disconnecting the AC power cord from either
the wall socket-outlet or the midspan appliance coupler.
–
The PoE injector "Data In" and "Data & Power Out" ports
are shielded RJ45 data sockets. They cannot be used as
Plain Old Telephone Service (POTS) telephone sockets.
Only RJ45 data connectors can be connected to these
sockets.
–
The Data In and Data & Power Out interfaces are qualified
as SELV (Safety Extra-Low Voltage) circuits according to
IEC 60950-1. These interfaces can only be connected to
SELV interfaces on other equipment.
Recycling and Disposal:
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
High PoE Midspan 60W,
Single port, AC in
Safety | en
7
Your Bosch product was developed and manufactured with highquality material and components that can be recycled and
reused. This symbol means that electronic and electrical
appliances, which have reached the end of their working life,
must be collected and disposed of separately from household
waste material. Separate collecting systems are usually in place
for disused electronic and electrical products. In the United
States, please dispose of these units at your local communal
waste collection point or at a recycling center. In the EU, please
dispose of these units at an environmentally compatible
recycling facility, per European Directive 2002/96/EC.
1.4
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security
Systems Service Center for authorization to return and shipping
instructions.
Service Centers
USA
Repair Center
Telephone: 800-566-2283 / Fax: 800-366-1329
E-mail: repair@us.bosch.com
Customer Service
Telephone: 888-289-0096 / Fax: 585-223-9180
E-mail: security.sales@us.bosch.com
Technical Support
Telephone: 800-326-1450 / Fax: 585-223-3508 or 717-735-6560
E-mail: technical.support@us.bosch.com
Canada
Telephone: 514-738-2434 / Fax: 514-738-8480
Europe, Middle East, Africa Region
Repair Center
Telephone: 31 (0) 76-5721500 / Fax: 31 (0) 76-5721413
E-mail: RMADesk.STService@nl.bosch.com
Asia Region
Repair Center
Bosch Security Systems
Installation Manual
2013.03 | 1.2 | F.01U.279.929
8
High PoE Midspan 60W,
Single port, AC in
en | Safety
Telephone: 65 63522776 / Fax: 65 63521776
E-mail: rmahelpdesk@sg.bosch.com
Customer Service
Telephone: 86 (0) 756 7633117 or 86 (0) 756 7633121 / Fax: 86
(0) 756 7631710
E-mail: customer.service@cn.bosch.com
Warranty and additional information
For additional information and warranty queries, please contact
your Bosch Security Systems representative or visit our website
at www.boschsecurity.com.
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
High PoE Midspan 60W,
Single port, AC in
Unpacking | en
2
Unpacking
2.1
Parts List
9
The package containing the High PoE Midspan 60W, Single port
should include the following items:
Quantity Part
2.2
1
High PoE Midspan 60W, Single port, AC in
1
120 V power cord
1
230 V power cord
1
Installation Manual (this document)
Additional Parts Required
The following table lists additional parts (not supplied by
Bosch) required to install the midspan:
Quantity
Part
Size
Notes
2
Mounting
Head diameter:
1.5 mm (0.059 in.)
screws;
5.8 mm
clearance from mounting
Select either
(0.23 in.)
surface
Head diameter:
2.5 mm (0.098 in.)
7 mm
clearance from mounting
(0.27 in.)
surface
size
(but not both).
Head height:
2 mm
(0.08 in.)
2
CAT5 cables
Not to exceed
1 cable to connect to the
100 m (333 ft)
“Data & Power
each
Out“ port.
1 cable to connect to the
“Data In” port.
Bosch Security Systems
Installation Manual
2013.03 | 1.2 | F.01U.279.929
10
2.3
High PoE Midspan 60W,
Single port, AC in
en | Unpacking
Tools Required
Screwdriver
2.4
Additional Parts Recommended But Not
Required
The following table lists additional parts (not supplied by
Bosch) recommended to install the midspan:
Quantity Part
1
Surge suppressor
1
Splitter
1
Universal Power Supply (UPS)
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
High PoE Midspan 60W,
Single port, AC in
3
System overview | en
11
System overview
The High PoE Midspan 60W, Single port, AC in is a high-power
PoE (Power over Ethernet) device that provides power over
Ethernet cabling between an Ethernet (remote network) switch
and an AutoDome 7000 Series camera. It supports the
IEEE802.3at and IEEE802.3af standards, while doubling the
output power to 60 W. The midspan is designed to carry gigabit
Ethernet data and power over a standard CAT5e cable, delivered
through all 4 pairs:
–
Alt A: pin 1,2 (-) and 3,6 (+)
–
Alt B: 4,5 (+) and 7.8 (-)
Note: Do NOT use cross-over cable between the Data & Power
Out port and the AutoDome camera!
Note: The midspan is not a repeater and does not amplify the
Ethernet data signal.
Note: The Ethernet cable length must be less than 100 meters
from the Ethernet source to the AutoDome camera.
Bosch Security Systems
Installation Manual
2013.03 | 1.2 | F.01U.279.929
12
High PoE Midspan 60W,
Single port, AC in
en | Installation
4
Installation
Caution!
Installation must be made by qualified personnel and conform
to ANSI/NFPA 70 (the National Electrical Code® (NEC)), Canadi-
!
an Electrical Code, Part I (also called CE Code or CSA C22.1),
and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for any damages or losses caused by incorrect
or improper installation.
The midspan can be placed on a desktop or mounted on a wall,
bench, or shelf using the rear side mounting holes.
Before mounting the midspan to a fixed location, note the
following:
–
Do not cover the midspan or block the airflow to the PoE
–
Keep the midspan away from excessive heat and humidity
with any foreign objects.
and free from vibration and dust.
–
Ensure that the cable length from the Ethernet network
source to the terminal does not exceed 100 meters (333
feet). The midspan is not a repeater and does not amplify
the Ethernet data signal.
–
No “on-off” switch exists; simply plug the midspan into an
AC power source.
Installing the Unit
Follow these steps in sequence to install the Bosch midspan.
1.
Select the mounting location and surface. Ensure that the
selected surface will be able to support the weight of the
unit (400 g / 0.88 lb). Note that this unit is intended only
for installation in a Restricted Access Location.
2.
Install two mounting screws in the selected mounting
surface, at a distance of 9.17 mm (3.61 in.) apart from the
center of each screw.
3.
Align the mounting slots on the unit to the screws.
4.
Proceed to the Connection chapter.
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
High PoE Midspan 60W,
Single port, AC in
Bosch Security Systems
Installation | en
Installation Manual
13
2013.03 | 1.2 | F.01U.279.929
14
High PoE Midspan 60W,
Single port, AC in
en | Connection
Connection
5
Notice!
The PoE ports “Data In“ and “Data & Power Out“ are shielded
RJ45 data sockets. They cannot be used as “Plain Old Tele-
i
phone Service” (POTS) telephone sockets. Connect only RJ45
data connectors (EIA 568A and 568B) to these ports.
The “Data In” and “Data & Power Out” interfaces are qualified
as “Safety Extra Low Voltage” (SELV) circuits according to IEC
60950-1. These interfaces can be connected only to SELV interfaces on other equipment.
1.
Connect the midspan to an AC power outlet (100 – 240
VAC), using one of the two power cords supplied, or one
that has the appropriate ratings and specifications (see the
Safety chapter).
Note: The voltage of the power outlet must match the
voltage indicated on the midspan label.
2.
Connect the Data In (input) port to the remote Ethernet
network switch.
3.
Connect the Data & Power Out (output) port to the
Ethernet port on the AutoDome camera.
Note: Do NOT use cross-over cable!
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
High PoE Midspan 60W,
Single port, AC in
Connection | en
15
Figure 5.1: Midspan_DataIn_DataOut_Connections
1 AC input connectivity indicator
2 Port connectivity indicator
3 CAT5 cable
4 Connection to AutoDome camera
5 Connection to Ethernet switch
4
If desired, connect a splitter close to the terminal, but not
on the midspan.
Bosch Security Systems
Installation Manual
2013.03 | 1.2 | F.01U.279.929
16
6
High PoE Midspan 60W,
Single port, AC in
en | Troubleshooting
Troubleshooting
LED Indicators
The following tables identify the indicators on the top of the
midspan.
AC LED
OFF
Green
Green
Power off indicator
Power on indicator
(power is active)
Port LED
–
Behavior
OFF
–
No detection or disconnected no
load is connected.
–
Yellow ON
–
Power supplied over data or spare
–
Green ON
–
Power supplied over data and spare
pairs together
–
Blinking yellow –
Over current or short circuit
at 1Hz rate
condition at one of the 2 pairs (the
other pair is OFF) - data or spare,
(PD or cable fault)
–
–
Blinking yellow –
Over current or short circuit
and green
condition at one or both pairs - data
at 1Hz rate
or/and spare, (PD or cable fault)
Blinking yellow –
Internal fault condition
or green 4Hz
rate
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
High PoE Midspan 60W,
Single port, AC in
Troubleshooting | en
17
Troubleshooting Steps
Symptom
–
Corrective Steps
The
1. Verify that a reliable power cord is used.
midspan
2. Verify that the voltage at the power inlet
does not
is between 100 and 240 VAC.
power up.
3. Remove and re-apply power to the device
and then check the indicators during power
up sequence.
–
The
1. Verify that the midspan detects the
midspan
camera.
does not
2. Verify that you are using a standard
operate, but Category 5/5e/6, straight-wired cable, with
no port
four pairs.
indicator is
3. If an external power splitter is used,
lit.
replace it with a splitter known to operate.
4. Verify that the input Ethernet cable is
connected to the Data In port.
5. Verify that the AutoDome camera is
connected to the Data & Power Out port.
6. Try to reconnect the camera to a different
midspan. If the camera works, then there is
probably a faulty port or RJ45 connection
on the midspan.
7. Verify that there is not a short over any of
the twisted pair cables or over the RJ45
connectors.
–
The
1. Verify that the port indicator on the front
AutoDome
panel is continuously lit.
camera
2. If an external power splitter is used,
operates,
replace it with a splitter known to operate.
but there is
3. Verify that for this link, you are using
no data link. standard UTP/FTP Category 5 straight (noncrossover) cabling, with all four pairs.
Bosch Security Systems
Installation Manual
2013.03 | 1.2 | F.01U.279.929
18
High PoE Midspan 60W,
Single port, AC in
en | Troubleshooting
Symptom
Corrective Steps
4. Verify that the Ethernet cable length is
less than 100 meters from the Ethernet
source to the AutoDome camera.
5. Try to reconnect the camera to a different
midspan. If the camera works, then there is
probably a faulty port or RJ45 connection
on the midspan.
2013.03 | 1.2 | F.01U.279.929
Installation Manual
Bosch Security Systems
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA, 17601
USA
www.boschsecurity.com
© Bosch Security Systems, Inc., 2013